Willem de Bruijn says:
====================
virtio-net tx napi
Add napi for virtio-net transmit completion processing.
Changes:
v2 -> v3:
- convert __netif_tx_trylock to __netif_tx_lock on tx napi poll
ensure that the handler always cleans, to avoid deadlock
- unconditionally clean in start_xmit
avoid adding an unnecessary "if (use_napi)" branch
- remove virtqueue_disable_cb in patch 5/5
a noop in the common event_idx based loop
- document affinity_hint_set constraint
v1 -> v2:
- disable by default
- disable unless affinity_hint_set
because cache misses add up to a third higher cycle cost,
e.g., in TCP_RR tests. This is not limited to the patch
that enables tx completion cleaning in rx napi.
- use trylock to avoid contention between tx and rx napi
- keep interrupts masked during xmit_more (new patch 5/5)
this improves cycles especially for multi UDP_STREAM, which
does not benefit from cleaning tx completions on rx napi.
- move free_old_xmit_skbs (new patch 3/5)
to avoid forward declaration
not changed:
- deduplicate virnet_poll_tx and virtnet_poll_txclean
they look similar, but have differ too much to make it
worthwhile.
- delay netif_wake_subqueue for more than 2 + MAX_SKB_FRAGS
evaluated, but made no difference
- patch 1/5
RFC -> v1:
- dropped vhost interrupt moderation patch:
not needed and likely expensive at light load
- remove tx napi weight
- always clean all tx completions
- use boolean to toggle tx-napi, instead
- only clean tx in rx if tx-napi is enabled
- then clean tx before rx
- fix: add missing braces in virtnet_freeze_down
- testing: add 4KB TCP_RR + UDP test results
Based on previous patchsets by Jason Wang:
[RFC V7 PATCH 0/7] enable tx interrupts for virtio-net
http://lkml.iu.edu/hypermail/linux/kernel/1505.3/00245.html
Before commit b0c39dbdc2 ("virtio_net: don't free buffers in xmit
ring") the virtio-net driver would free transmitted packets on
transmission of new packets in ndo_start_xmit and, to catch the edge
case when no new packet is sent, also in a timer at 10HZ.
A timer can cause long stalls. VIRTIO_F_NOTIFY_ON_EMPTY avoids stalls
due to low free descriptor count. It does not address a stalls due to
low socket SO_SNDBUF. Increasing timer frequency decreases that stall
time, but increases interrupt rate and, thus, cycle count.
Currently, with no timer, packets are freed only at ndo_start_xmit.
Latency of consume_skb is now unbounded. To avoid a deadlock if a sock
reaches SO_SNDBUF, packets are orphaned on tx. This breaks TCP small
queues.
Reenable TCP small queues by removing the orphan. Instead of using a
timer, convert the driver to regular tx napi. This does not have the
unresolved stall issue and does not have any frequency to tune.
By keeping interrupts enabled by default, napi increases tx
interrupt rate. VIRTIO_F_EVENT_IDX avoids sending an interrupt if
one is already unacknowledged, so makes this more feasible today.
Combine that with an optimization that brings interrupt rate
back in line with the existing version for most workloads:
Tx completion cleaning on rx interrupts elides most explicit tx
interrupts by relying on the fact that many rx interrupts fire.
Tested by running {1, 10, 100} {TCP, UDP} STREAM, RR, 4K_RR benchmarks
from a guest to a server on the host, on an x86_64 Haswell. The guest
runs 4 vCPUs pinned to 4 cores. vhost and the test server are
pinned to a core each.
All results are the median of 5 runs, with variance well < 10%.
Used neper (github.com/google/neper) as test process.
Napi increases single stream throughput, but increases cycle cost.
The optimizations bring this down. The previous patchset saw a
regression with UDP_STREAM, which does not benefit from cleaning tx
interrupts in rx napi. This regression is now gone for 10x, 100x.
Remaining difference is higher 1x TCP_STREAM, lower 1x UDP_STREAM.
The latest results are with process, rx napi and tx napi affine to
the same core. All numbers are lower than the previous patchset.
upstream napi
TCP_STREAM:
1x:
Mbps 27816 39805
Gcycles 274 285
10x:
Mbps 42947 42531
Gcycles 300 296
100x:
Mbps 31830 28042
Gcycles 279 269
TCP_RR Latency (us):
1x:
p50 21 21
p99 27 27
Gcycles 180 167
10x:
p50 40 39
p99 52 52
Gcycles 214 211
100x:
p50 281 241
p99 411 337
Gcycles 218 226
TCP_RR 4K:
1x:
p50 28 29
p99 34 36
Gcycles 177 167
10x:
p50 70 71
p99 85 134
Gcycles 213 214
100x:
p50 442 611
p99 802 785
Gcycles 237 216
UDP_STREAM:
1x:
Mbps 29468 26800
Gcycles 284 293
10x:
Mbps 29891 29978
Gcycles 285 312
100x:
Mbps 30269 30304
Gcycles 318 316
UDP_RR:
1x:
p50 19 19
p99 23 23
Gcycles 180 173
10x:
p50 35 40
p99 54 64
Gcycles 245 237
100x:
p50 234 286
p99 484 473
Gcycles 224 214
Note that GSO is enabled, so 4K RR still translates to one packet
per request.
Lower throughput at 100x vs 10x can be (at least in part)
explained by looking at bytes per packet sent (nstat). It likely
also explains the lower throughput of 1x for some variants.
upstream:
N=1 bytes/pkt=16581
N=10 bytes/pkt=61513
N=100 bytes/pkt=51558
at_rx:
N=1 bytes/pkt=65204
N=10 bytes/pkt=65148
N=100 bytes/pkt=56840
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tx napi mode increases the rate of transmit interrupts. Suppress some
by masking interrupts while more packets are expected. The interrupts
will be reenabled before the last packet is sent.
This optimization reduces the througput drop with tx napi for
unidirectional flows such as UDP_STREAM that do not benefit from
cleaning tx completions in the the receive napi handler.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amortize the cost of virtual interrupts by doing both rx and tx work
on reception of a receive interrupt if tx napi is enabled. With
VIRTIO_F_EVENT_IDX, this suppresses most explicit tx completion
interrupts for bidirectional workloads.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An upcoming patch will call free_old_xmit_skbs indirectly from
virtnet_poll. Move the function above this to avoid having to
introduce a forward declaration.
This is a pure move: no code changes.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert virtio-net to a standard napi tx completion path. This enables
better TCP pacing using TCP small queues and increases single stream
throughput.
The virtio-net driver currently cleans tx descriptors on transmission
of new packets in ndo_start_xmit. Latency depends on new traffic, so
is unbounded. To avoid deadlock when a socket reaches its snd limit,
packets are orphaned on tranmission. This breaks socket backpressure,
including TSQ.
Napi increases the number of interrupts generated compared to the
current model, which keeps interrupts disabled as long as the ring
has enough free descriptors. Keep tx napi optional and disabled for
now. Follow-on patches will reduce the interrupt cost.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare virtio-net for tx napi by converting existing napi code to
use helper functions. This also deduplicates some logic.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doing a full 64-bit decomposition is really stupid especially for
simple values like 0 and -1.
But if we are going to optimize this, go all the way and try for all 2
and 3 instruction sequences not requiring a temporary register as
well.
First we do the easy cases where it's a zero or sign extended 32-bit
number (sethi+or, sethi+xor, respectively).
Then we try to find a range of set bits we can load simply then shift
up into place, in various ways.
Then we try negating the constant and see if we can do a simple
sequence using that with a xor at the end. (f.e. the range of set
bits can't be loaded simply, but for the negated value it can)
The final optimized strategy involves 4 instructions sequences not
needing a temporary register.
Otherwise we sadly fully decompose using a temp..
Example, from ALU64_XOR_K: 0x0000ffffffff0000 ^ 0x0 = 0x0000ffffffff0000:
0000000000000000 <foo>:
0: 9d e3 bf 50 save %sp, -176, %sp
4: 01 00 00 00 nop
8: 90 10 00 18 mov %i0, %o0
c: 13 3f ff ff sethi %hi(0xfffffc00), %o1
10: 92 12 63 ff or %o1, 0x3ff, %o1 ! ffffffff <foo+0xffffffff>
14: 93 2a 70 10 sllx %o1, 0x10, %o1
18: 15 3f ff ff sethi %hi(0xfffffc00), %o2
1c: 94 12 a3 ff or %o2, 0x3ff, %o2 ! ffffffff <foo+0xffffffff>
20: 95 2a b0 10 sllx %o2, 0x10, %o2
24: 92 1a 60 00 xor %o1, 0, %o1
28: 12 e2 40 8a cxbe %o1, %o2, 38 <foo+0x38>
2c: 9a 10 20 02 mov 2, %o5
30: 10 60 00 03 b,pn %xcc, 3c <foo+0x3c>
34: 01 00 00 00 nop
38: 9a 10 20 01 mov 1, %o5 ! 1 <foo+0x1>
3c: 81 c7 e0 08 ret
40: 91 eb 40 00 restore %o5, %g0, %o0
Signed-off-by: David S. Miller <davem@davemloft.net>
cbcond combines a compare with a branch into a single instruction.
The limitations are:
1) Only newer chips support it
2) For immediate compares we are limited to 5-bit signed immediate
values
3) The branch displacement is limited to 10-bit signed
4) We cannot use it for JSET
Also, cbcond (unlike all other sparc control transfers) lacks a delay
slot.
Currently we don't have a useful instruction we can push into the
delay slot of normal branches. So using cbcond pretty much always
increases code density, and is therefore a win.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Alemayhu says:
====================
Misc BPF cleanup
while looking into making the Makefile in samples/bpf better handle O= I saw
several warnings when running `make clean && make samples/bpf/`. This series
reduces those warnings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following warning
samples/bpf/test_lru_dist.c:28:0: warning: "offsetof" redefined
#define offsetof(TYPE, MEMBER) ((size_t)&((TYPE *)0)->MEMBER)
In file included from ./tools/lib/bpf/bpf.h:25:0,
from samples/bpf/libbpf.h:5,
from samples/bpf/test_lru_dist.c:24:
/usr/lib/gcc/x86_64-redhat-linux/6.3.1/include/stddef.h:417:0: note: this is the location of the previous definition
#define offsetof(TYPE, MEMBER) __builtin_offsetof (TYPE, MEMBER)
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following warning
samples/bpf/cookie_uid_helper_example.c: At top level:
samples/bpf/cookie_uid_helper_example.c:276:6: warning: no previous prototype for ‘finish’ [-Wmissing-prototypes]
void finish(int ret)
^~~~~~
HOSTLD samples/bpf/per_socket_stats_example
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was initially going to remove '-Wno-address-of-packed-member' because I
thought it was not supposed to be there but Daniel suggested using
'-Wno-unknown-warning-option'.
This silences several warnings similiar to the one below
warning: unknown warning option '-Wno-address-of-packed-member' [-Wunknown-warning-option]
1 warning generated.
clang -nostdinc -isystem /usr/lib/gcc/x86_64-redhat-linux/6.3.1/include -I./arch/x86/include -I./arch/x86/include/generated/uapi -I./arch/x86/include/generated -I./include
-I./arch/x86/include/uapi -I./include/uapi -I./include/generated/uapi -include ./include/linux/kconfig.h \
-D__KERNEL__ -D__ASM_SYSREG_H -Wno-unused-value -Wno-pointer-sign \
-Wno-compare-distinct-pointer-types \
-Wno-gnu-variable-sized-type-not-at-end \
-Wno-address-of-packed-member -Wno-tautological-compare \
-O2 -emit-llvm -c samples/bpf/xdp_tx_iptunnel_kern.c -o -| llc -march=bpf -filetype=obj -o samples/bpf/xdp_tx_iptunnel_kern.o
$ clang --version
clang version 3.9.1 (tags/RELEASE_391/final)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /usr/bin
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that also the last in-tree user of the xdp_adjust_head bit has
been removed, we can remove the flag from struct bpf_prog altogether.
This, at the same time, also makes sure that any future driver for
XDP comes with bpf_xdp_adjust_head() support right away.
A rejection based on this flag would also mean that tail calls
couldn't be used with such driver as per c2002f9837 ("bpf: fix
checking xdp_adjust_head on tail calls") fix, thus lets not allow
for it in the first place.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function pci_find_ext_capability() may return 0, which is an invalid
address. In function qlcnic_sriov_virtid_fn(), its return value is used
without validation. This may result in invalid memory access bugs. This
patch fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function pc300_pci_init_one(), on the ioremap error path, function
pc300_pci_remove_one() is called to free the allocated memory. However,
the path is not terminated, and the freed memory will be used later,
resulting in use-after-free bugs. This path fixes the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function nlmsg_new() will return a NULL pointer if there is no enough
memory, and its return value should be checked before it is used.
However, in function tipc_nl_node_get_monitor(), the validation of the
return value of function nlmsg_new() is missed. This patch fixes the
bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function nla_nest_start() may return a NULL pointer on error. However,
in function lwtunnel_fill_encap(), the return value of nla_nest_start()
is not validated before it is used. This patch checks the return value
of nla_nest_start() against NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: DMA flags, adjust head and fixes
This series takes advantage of Alex's DMA_ATTR_SKIP_CPU_SYNC to make
XDP packet modifications "correct" from DMA API point of view. It
also allows us to parse the metadata before we run XDP at no additional
DMA sync cost. That way we can get rid of the metadata memcpy, and
remove the last upstream user of bpf_prog->xdp_adjust_head.
David's patch adds a way to read capabilities from the management
firmware.
There are also two net-next fixes. Patch 4 which fixes what seems to
be a result of a botched rebase on my part. Patch 5 corrects locking
when state of ethernet ports is being refreshed.
v3: move the sync from alloc func to the actual give to hw func
v2: sync rx buffers before giving them to the card (Alex)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code refreshing the eth port state was trying to update state
of all ports of the card. Unfortunately to safely walk the port
list we would have to hold the port lock, which we can't due to
lock ordering constraints against rtnl.
Make the per-port sync refresh and async refresh of all ports
completely separate routines.
Fixes: 172f638c93 ("nfp: add port state refresh")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP headroom should not be included in free list buffer size.
Fixes: 6fe0c3b438 ("nfp: add support for xdp_adjust_head()")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve identifying information from the NSP. For now it only
contains versions of firmware subcomponents.
Signed-off-by: David Brunecz <david.brunecz@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling memcpy to shift metadata out of the way for XDP to run
seems like an overkill. The most common metadata contents are
8 bytes containing type and flow hash. Simply parse the metadata
before we run XDP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA unmap may destroy changes CPU made to the buffer. To make XDP
run correctly on non-x86 platforms we should use the
DMA_ATTR_SKIP_CPU_SYNC attribute.
Thanks to using the attribute we can now push the sync operation to the
common code path from XDP handler.
A little bit of variable name reshuffling is required to bring the
code back to readable state.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin LaHaise says:
====================
flower: add MPLS matching support
This patch series adds support for parsing MPLS flows in the flow dissector
and the flower classifier. Each of the MPLS TTL, BOS, TC and Label fields
can be used for matching.
v2: incorporate style feedback, move #defines to linux/include/mpls.h
Note: this omits Jiri's request to remove tabs between the type and
field names in struct declarations. This would be inconsistent with
numerous other struct definitions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to the tc flower classifier to match based on fields in MPLS
labels (TTL, Bottom of Stack, TC field, Label).
Signed-off-by: Benjamin LaHaise <benjamin.lahaise@netronome.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Cc: Gao Feng <fgao@ikuai8.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for parsing MPLS flows to the flow dissector in preparation for
adding MPLS match support to cls_flower.
Signed-off-by: Benjamin LaHaise <benjamin.lahaise@netronome.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Eric Dumazet <jhs@mojatatu.com>
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Cc: Gao Feng <fgao@ikuai8.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang says:
====================
net/tcp_fastopen: Fix for various TFO firewall issues
Currently there are still some firewall issues in the middlebox
which make the middlebox drop packets silently for TFO sockets.
This kind of issue is hard to be detected by the end client.
This patch series tries to detect such issues in the kernel and disable
TFO temporarily.
More details about the issues and the fixes are included in the following
patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Paasch from Apple found another firewall issue for TFO:
After successful 3WHS using TFO, server and client starts to exchange
data. Afterwards, a 10s idle time occurs on this connection. After that,
firewall starts to drop every packet on this connection.
The fix for this issue is to extend existing firewall blackhole detection
logic in tcp_write_timeout() by removing the mss check.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This counter records the number of times the firewall blackhole issue is
detected and active TFO is disabled.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Middlebox firewall issues can potentially cause server's data being
blackholed after a successful 3WHS using TFO. Following are the related
reports from Apple:
https://www.nanog.org/sites/default/files/Paasch_Network_Support.pdf
Slide 31 identifies an issue where the client ACK to the server's data
sent during a TFO'd handshake is dropped.
C ---> syn-data ---> S
C <--- syn/ack ----- S
C (accept & write)
C <---- data ------- S
C ----- ACK -> X S
[retry and timeout]
https://www.ietf.org/proceedings/94/slides/slides-94-tcpm-13.pdf
Slide 5 shows a similar situation that the server's data gets dropped
after 3WHS.
C ---- syn-data ---> S
C <--- syn/ack ----- S
C ---- ack --------> S
S (accept & write)
C? X <- data ------ S
[retry and timeout]
This is the worst failure b/c the client can not detect such behavior to
mitigate the situation (such as disabling TFO). Failing to proceed, the
application (e.g., SSL library) may simply timeout and retry with TFO
again, and the process repeats indefinitely.
The proposed solution is to disable active TFO globally under the
following circumstances:
1. client side TFO socket detects out of order FIN
2. client side TFO socket receives out of order RST
We disable active side TFO globally for 1hr at first. Then if it
happens again, we disable it for 2h, then 4h, 8h, ...
And we reset the timeout to 1hr if a client side TFO sockets not opened
on loopback has successfully received data segs from server.
And we examine this condition during close().
The rational behind it is that when such firewall issue happens,
application running on the client should eventually close the socket as
it is not able to get the data it is expecting. Or application running
on the server should close the socket as it is not able to receive any
response from client.
In both cases, out of order FIN or RST will get received on the client
given that the firewall will not block them as no data are in those
frames.
And we want to disable active TFO globally as it helps if the middle box
is very close to the client and most of the connections are likely to
fail.
Also, add a debug sysctl:
tcp_fastopen_blackhole_detect_timeout_sec:
the initial timeout to use when firewall blackhole issue happens.
This can be set and read.
When setting it to 0, it means to disable the active disable logic.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse and compiler warnings fixes from Stephen Hemminger.
From Roi Dayan and Or Gerlitz, Add devlink and mlx5 support for controlling
E-Switch encapsulation mode, this knob will enable HW support for applying
encapsulation/decapsulation to VF traffic as part of SRIOV e-switch offloading.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJY+5cRAAoJEEg/ir3gV/o+5c8H/1/khPzy26B2lWyjPC8CRCQF
eSd0tiHLgIqbZTbnIHTR+NbZ/SUFaukoJi8OKn1fGFHCCajWvPP4xkENVKrUdi3q
kOgNZb/R1V0j6SdELyoMalFPjAscTgdmwYMnry+vcjOxJ+H2uUTnMKXwFf8IsBjz
EINy8oZ5jZcejmft0c2O5HN4Bt/7U5ttM3CroAdcvPT9lq2DFJL2uCABhTO/1DdY
b7uVa47FnkqxX19Ebn7fjp5r3diGYOmCPMjdC89C//rbkLB8FN61EkcSLpGY3YNm
djmCPQ+xaa3ielmBpOk3AMayFEtYW0nDMj9eWECVByadRQZ2qz9wTVXBp5CX9zg=
=E3Jt
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-04-22' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-04-22
Sparse and compiler warnings fixes from Stephen Hemminger.
From Roi Dayan and Or Gerlitz, Add devlink and mlx5 support for controlling
E-Switch encapsulation mode, this knob will enable HW support for applying
encapsulation/decapsulation to VF traffic as part of SRIOV e-switch offloading.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-04-22
Here are some more Bluetooth patches (and one 802.15.4 patch) in the
bluetooth-next tree targeting the 4.12 kernel. Most of them are pure
fixes.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err message and rejoin
line.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use offset_in_page() macro instead of open-coding.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Updates for net-next.
Miscellaneous updates include passing DCBX RoCE VLAN priority to firmware,
checking one more new firmware flag before allowing DCBX to run on the host,
adding 100Gbps speed support, adding check to disallow speed settings on
Multi-host NICs, and a minor fix for reporting VF attributes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change restricts the PF in multi-host mode from setting any port
level PHY configuration. The settings are controlled by firmware in
Multi-Host mode.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the additional flag in bnxt_hwrm_func_qcfg() before allowing
DCBX to be done in host mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for 100G link speed reporting for Broadcom BCM57454
ASIC in ethtool command.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .ndo_get_vf_config() is returning the wrong qos attribute. Fix
the code that checks and reports the qos and spoofchk attributes. The
BNXT_VF_QOS and BNXT_VF_LINK_UP flags should not be set by default
during init. time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver gets the RoCE app priority set/delete call through DCBNL,
the driver will send the information to the firmware to set up the
priority VLAN tag for RDMA traffic.
[ New version using the common ETH_P_IBOE constant in if_ether.h ]
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new optional conntrack action attribute OVS_CT_ATTR_EVENTMASK,
which can be used in conjunction with the commit flag
(OVS_CT_ATTR_COMMIT) to set the mask of bits specifying which
conntrack events (IPCT_*) should be delivered via the Netfilter
netlink multicast groups. Default behavior depends on the system
configuration, but typically a lot of events are delivered. This can be
very chatty for the NFNLGRP_CONNTRACK_UPDATE group, even if only some
types of events are of interest.
Netfilter core init_conntrack() adds the event cache extension, so we
only need to set the ctmask value. However, if the system is
configured without support for events, the setting will be skipped due
to extension not being found.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Reviewed-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typo in a comment.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Greg Rose <gvrose8192@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Fontenot says:
====================
ibmvnic: Additional updates and bug fixes
This set of patches is an additional set of updates and bug fixes to
the ibmvnic driver which applies on top of the previous set of updates
sent out on 4/19.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error is encountered during transmit we need to free the
skb instead of returning TX_BUSY.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate that the napi structs exist before trying to disable them
at driver close.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a common routine for setting the link state for the vnic adapter.
This update moves the sending of the crq and waiting for the link state
response to a common place. The new routine also adds handling of
resending the crq in cases of getting a partial success response.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should be initializing the stats token in the same place we
initialize the other resources for the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling a fatal error in the driver, there can be additional
error information provided by the vios. This information is not
always present, so only retrieve the additional error information
when present.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a modification in the PAPR+ specification which now
defines a previously reserved value for vNIC capabilities. It indicates
whether the system firmware performs a VLAN header stripping on all VLAN
tagged received frames, in case it does, the behavior expected is for
the ibmvnic driver to be responsible for inserting the VLAN header.
Reported-by: Manvanthara B. Puttashankar <mputtash@in.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
