This patch set adds interrupt support for the igc interfaces.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have the ability to configure the basic settings on the device
we can start allocating and configuring a netdev for the interface.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the basic defines and structures needed by the PF for
operation. With this it is possible to bring up the interface,
but without being able to configure any of the filters on
the interface itself.
Add skeleton for a function pointers.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the beginning framework onto which I am going to add
the igc driver which supports the Intel(R) I225-LM/I225-V 2.5G
Ethernet Controller.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When sending a big fragment using multiple buffer descriptor,
hns3 does one maping, but do multiple unmapping when tx is done,
which may cause unmapping problem.
To fix it, this patch makes sure the value of desc_cb.length of
the non-first bd is zero. If desc_cb.length is zero, we do not
unmap the buffer.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep symmetrical, this patch renames hns_nic_dma_unmap to
hns3_clear_desc.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch unifies big tx fragment handling for tso and non-tso
case.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To solve the L3 checksum error problem which happens when driver
does not clear L3 checksum, DMA map should be done after calling
skb_cow_head.
This patch moves DMA map into hns3_fill_desc to ensure that DMA
map is done after calling skb_cow_head.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes hns3_fill_desc_tso in preparation for
fixing some desc filling bug, because for tso or non-tso
case, we will use the unified hns3_fill_desc.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newly added link modes are required to be added
during setting link modes. If the new link mode
is not available during qed_set_link, it may cause
link getting down due to empty supported capability,
being passed to MFW, after setting autoneg off/on
with current/supported speed.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set link mode after checking available "supported" link caps
of the port.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added transceiver type, speed capability and board types
in HSI, are utilizing to display the accurate link
information in ethtool.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added transceiver modes with different speed and media type,
speed capability and supported board types in HSI, which
will be utilizing to display correct specification of link
modes and speed type.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the use of local PTT to propagate through the qed_mcp* API's.
Global ptt should not be used.
Register access should be done through layers. Register address is
mapped into a PTT, PF translation table. Several interface functions
require a PTT to direct read/write into register. There is a pool of
PTT maintained, and several PTT are used simultaneously to access
device registers in different flows. Same PTT should not be used in
flows that can run concurrently.
To avoid running out of PTT resources, too many PTT should not be
acquired without releasing them. Every PF has a global PTT, which is
used throughout the life of PF, in most important flows for register
access. Generic functions acquire the PTT locally and release after
the use. This patch aligns the use of Global PTT and Local PTT
accordingly.
Signed-off-by: Rahul Verma <rahul.verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils_fw2x.c:282:5: warning:
symbol 'aq_fw2x_update_stats' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new poll function that polls for NQ events. If the NQ event is
a CQ notification, we locate the CP ring from the cq_handle and call
__bnxt_poll_work() to handle RX/TX events on the CP ring.
Add a new has_more_work field in struct bnxt_cp_ring_info to indicate
budget has been reached. __bnxt_poll_cqs_done() is called to update or
ARM the CP rings if budget has not been reached or not. If budget
has been reached, the next bnxt_poll_p5() call will continue to poll
from the CQ rings directly. Otherwise, the NQ will be ARMed for the
next IRQ.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the CP ring polling logic in bnxt_poll_work() into 2 separate
functions __bnxt_poll_work() and __bnxt_poll_work_done(). Since the logic
is separated, we need to add tx_pkts and events fields to struct bnxt_napi
to keep track of the events to handle between the 2 functions. We also
add had_work_done field to struct bnxt_cp_ring_info to indicate whether
some work was performed on the CP ring.
This is needed to better support the 57500 chips. We need to poll up to
2 separate CP rings before we update or ARM the CP rings on the 57500 chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On legacy chips, the CP ring may be shared between RX and TX and so only
setup the RX coalescing parameters in such a case. On 57500 chips, we
always have a dedicated CP ring for TX so we can always set up the
TX coalescing parameters in bnxt_hwrm_set_coal().
Also, the min_timer coalescing parameter applies to the NQ on the new
chips and a separate firmware call needs to be made to set it up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the RX code path, we current use the bnxt_napi struct pointer to
identify the associated RX/CP rings. Change it to use the struct
bnxt_cp_ring_info pointer instead since there are now up to 2
CP rings per MSIX.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS context allocation and RSS indirection table setup are very different
on the new chip. Refactor bnxt_setup_vnic() to call 2 different functions
to set up RSS for the vnic based on chip type. On the new chip, the
number of RSS contexts and the indirection table size depends on the
number of RX rings. Each indirection table entry is also different
on the new chip since ring groups are no longer used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the new 57500 chips, we need to allocate one RSS context for every
64 RX rings. In previous chips, only one RSS context per vnic is
required regardless of the number of RX rings. So increase the max
RSS context array count to 8.
Hardware ring groups are not used on the new chips. Note that the
software ring group structure is still maintained in the driver to
keep track of the rings associated with the vnic.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the new 57500 chips, we allocate/free one CP ring for each RX ring or
TX ring separately. Using separate CP rings for RX/TX is an improvement
as TX events will no longer be stuck behind RX events.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware ring allocation semantics are slightly different for most
ring types on 57500 chips. Allocation/deallocation for NQ rings are
also added for the new chips.
A CP ring handle is also added so that from the NQ interrupt event,
we can locate the CP ring.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the new 57500 chips, getting the associated CP ring ID associated with
an RX ring or TX ring is different than before. On the legacy chips,
we find the associated ring group and look up the CP ring ID. On the
57500 chips, each RX ring and TX ring has a dedicated CP ring even if
they share the MSIX. Use these helper functions at appropriate places
to get the CP ring ID.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 57500 chips, the original bnxt_cp_ring_info struct now refers to the
NQ. bp->cp_nr_rings refer to the number of NQs on 57500 chips. There
are now 2 pointers for the CP rings associated with RX and TX rings.
Modify bnxt_alloc_cp_rings() and bnxt_free_cp_rings() accordingly.
With multiple CP rings per NAPI, we need to add a pointer in
bnxt_cp_ring_info struct to point back to the bnxt_napi struct.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ring reservation functions have to be modified for P5 chips in the
following ways:
- bnxt_cp_ring_info structs map to internal NQs as well as CP rings.
- Ring groups are not used.
- 1 CP ring must be available for each RX or TX ring.
- number of RSS contexts to reserve is multiples of 64 RX rings.
- RFS currently not supported.
Also, RX AGG rings are only used for jumbo frames, so we need to
unconditionally call bnxt_reserve_rings() in __bnxt_open_nic()
to see if we need to reserve AGG rings in case MTU has changed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the maximum MSIX capability in PCIe config. space earlier. When
we call firmware to query capability, we need to compare the PCIe
MSIX max count with the firmware count and use the smaller one as
the MSIX count for 57500 (P5) chips.
The new chips don't use ring groups. But previous chips do and
the existing logic limits the available rings based on resource
calculations including ring groups. Setting the max ring groups to
the max rx rings will work on the new chips without changing the
existing logic.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57500 series chips have a new 64-bit doorbell format. Use a new
bnxt_db_info structure to unify the new and the old 32-bit doorbells.
Add a new bnxt_set_db() function to set up the doorbell addreses and
doorbell keys ahead of time. Modify and introduce new doorbell
helpers to help abstract and unify the old and new doorbells.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
57500 series is a new chip class (P5) that requires some driver changes
in the next several patches. This adds basic chip ID, doorbells, and
the notification queue (NQ) structures. Each MSIX is associated with an
NQ instead of a CP ring in legacy chips. Each NQ has up to 2 associated
CP rings for RX and TX. The same bnxt_cp_ring_info struct will be used
for the NQ.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call firmware to configure the DMA addresses of all context memory
pages on new devices requiring context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New device requires host context memory as a backing store. Call
firmware to check for context memory requirements and store the
parameters. Allocate host pages accordingly.
We also need to move the call bnxt_hwrm_queue_qportcfg() earlier
so that all the supported hardware queues and the IDs are known
before checking and allocating context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips require the PTU_PTE_VALID bit to be set for every page
table entry for context memory and rings. Additional bits are also
required for page table entries for all rings. Add a flags field to
bnxt_ring_mem_info struct to specify these additional bits to be used
when setting up the pages tables as needed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DMA page table and vmem fields in bnxt_ring_struct to a new
bnxt_ring_mem_info struct. This will allow context memory management
for a new device to re-use some of the existing infrastructure.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware spec. allows interrupt coalescing parameters, such as
maximums, timer units, supported features to be queried. Update
the driver to make use of the new call to query these parameters
and provide the legacy defaults if the call is not available.
Replace the hard-coded values with these parameters.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the max_ext_req_len field from the HWRM_VER_GET_RESPONSE.
If this field is valid and greater than the mailbox size, use the
short command format to send firmware messages greater than the
mailbox size. Newer devices use this method to send larger messages
to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest firmware spec. has some additional rx extended port stats and new
tx extended port stats added. We now need to check the size of the
returned rx and tx extended stats and determine how many counters are
valid. New counters added include CoS byte and packet counts for rx
and tx.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Among the new changes are trusted VF support, 200Gbps support, and new
API to dump ring information on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_device_detach() stops all tx queues already, so we don't need
this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify this function, no functional change intended.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added driver causes a warning about a function that is
not used anywhere:
drivers/net/ethernet/marvell/octeontx2/af/cgx.c:320:12: error: 'cgx_fwi_link_change' defined but not used [-Werror=unused-function]
Remove it for now, until a user gets added. If we want to use this
function from another module, we also need a declaration in a header
file, which is currently missing, so it would have to change anyway.
Fixes: 1463f382f5 ("octeontx2-af: Add support for CGX link management")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes it possible to use devlink to split the 100G CXP
Netronome into two 40G interfaces. Currently when you ask for 2
interfaces, the math in src/nfp_devlink.c:nfp_devlink_port_split
calculates that you want 5 lanes per port because for some reason
eth_port.port_lanes=10 (shouldn't this be 12 for CXP?). What we really
want when asking for 2 breakout interfaces is 4 lanes per port. This
commit makes that happen by calculating based on 8 lanes if 10 are
present.
Signed-off-by: Ryan C Goodfellow <rgoodfel@isi.edu>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Greg Weeks <greg.weeks@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the hardware ArchDef, the PTV1 field in FD[CTRL]
is ignored by WRIOP, so setting it for Tx FDs is pointless.
Remove all references to it from the code.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ch parameter is never used in the dpaa2_eth_tx_conf function but
since its prototype must match the type defined in the consume field of
struct dpaa2_eth_fq, just mark it as __always_unused.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The priv parameter is never used in the build_linear_skb and
drain_channel function. Remove it from the function definitions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All 3 cases of possible uninitialized variables are false
positives since they are used only as output parameters.
Nonetheless, fix the warnings.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dpaa2_eth_set_dist_key function is only used in a single file.
Make it static.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both ARCH_LAYERSCAPE and COMPILE_TEST dependencies are already implied
through the FSL_MC_BUS dep, so there's no need to state it explicitly.
Also, the fsl-mc bus depends on COMPILE_TEST only for some
architectures (arm, arm64, ppc, x86), so it's not correct to
claim build support unconditionally.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dual-emac mode the cpsw driver sends directed packets, that means
that packets go to the directed port, but an ALE lookup is performed
to determine untagged egress only. It means that on tx side no need
to add port bit for ALE mcast entry mask, and basically ALE entry
for port identification is needed only on rx side.
So, add only host port in dual_emac mode as used directed
transmission, and no need in one more port. For single port boards
and switch mode all ports used, as usual, so no changes for them.
Also it simplifies farther changes.
In other words, mcast entries for dual-emac should behave exactly
like unicast. It also can help avoid leaking packets between ports
with same vlan on h/w level if ports could became members of same vid.
So now, for instance, if mcast address 33:33:00:00:00:01 is added then
entries in ALE table:
vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x1
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x1
Instead of:
vid = 1, addr = 33:33:00:00:00:01, port_mask = 0x3
vid = 2, addr = 33:33:00:00:00:01, port_mask = 0x5
With the same considerations, set only host port for unregistered
mcast for dual-emac mode in case of IFF_ALLMULTI is set, exactly like
it's done in cpsw_ale_set_allmulti().
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever kernel or user decides to call rx mode update, it clears
every multicast entry from forwarding table and in some time adds
it again. This time can be enough to drop incoming multicast packets.
That's why clear only staled multicast entries and update or add new
one afterwards.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
