The ehci-hcd driver is a little haphazard about keeping track of the
state of the USBCMD register. The ehci->command field is supposed to
hold the register's value (apart from a few special bits) at all
times, but it isn't maintained properly.
This patch (as1543) cleans up the situation. It keeps ehci->command
up-to-date, and uses that value rather than reading the register from
the hardware whenever possible.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the conflict in:
drivers/usb/host/ehci-fsl.c
And picks up loads of xhci bugfixes to make it easier for others to test
with.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gHlK
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Zack Parsons <k3bacon@gmail.com>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Cesar Miquel <miquel@df.uba.ar>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Juergen Stuber <starblue@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Michael Hund <mhund@ld-didactic.de>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
err() was a very old USB-specific macro that I thought had
gone away. This patch removes it from being used in the
driver and uses dev_err() instead.
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: David Howells <dhowells@redhat.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed too small hardcoded timeout values for usb_control_msg
in driver for SiliconLabs cp210x-based usb-to-serial adapters.
Replaced with USB_CTRL_GET_TIMEOUT/USB_CTRL_SET_TIMEOUT.
Signed-off-by: Yuri Matylitski <ym@tekinsoft.com>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the recent change to remove the module parameters from the ipaq
driver, we ended up with a duplicate id in the driver. This patch
removes it.
Reported-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch added the support of MCS7810 device for the mos7840 driver.
The MCS7810 device supports single USB2.0-to-Serial port with
a LED indicator for reflecting transmission or reception activity.
Signed-off-by: Donald Lee <donald@asix.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add EHCI driver for MIPS SEAD-3 development platform.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We changed the API here a couple months ago. It suspend() only takes
one argument now. GCC complains about this:
drivers/usb/host/bcma-hcd.c:320:2: warning: initialization from
incompatible pointer type [enabled by default]
drivers/usb/host/bcma-hcd.c:320:2: warning: (near initialization
for ‘bcma_hcd_driver.suspend’) [enabled by default]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the ClearPortFeature/USB_PORT_FEAT_ENABLE case, ehci_hub_control()
would read from status_reg, clear PORT_PE, and write the result back to
status_reg. This would clear any bits in PORT_RWC_BITS that were set in
the registers. Fix this by masking these bits off before the write.
Since this masking is common across all ClearPortFeature cases, move it
into a single early location to avoid duplicating it.
Remove the same bugfix from ehci-tegra.c's tegra_ehci_hub_control(), now
that this case is correctly handled by the core.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is for devices that are no longer being made, so the ability
to add new device ids when loading the module is not a feature that
anyone uses anymore. So remove it, which simplifies the startup code a
lot, and saves space.
If you still need to dynamically load device ids, that can be done
through sysfs.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is for devices that are no longer being made, so the ability
to add new device ids when loading the module is not a feature that
anyone uses anymore. So remove it, which simplifies the startup code a
lot, and saves space.
If you still need to dynamically load device ids, that can be done
through sysfs.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
these drivers are used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for them.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This call is not needed; the IRQ controller should (and does) set up
interrupts correctly. set_irq_flags() isn't exported to modules, to
this also fixes compilation of ehci-tegra.c as a module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb
structure, and this causes BUG_ON with some USB host implementations.
This patch fixes the issue.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removes allocation of coherent buffer for the control-request setup-packet
buffer from the yurex driver. Using coherent buffers for setup-packet is
obsolete and does not work with some USB host implementations.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Free the two previously allocated buffers before exiting the function in an
error case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed the assignment statements found in if statements by the
checkpatch.pl tool.
Signed-off-by: Adhir Ramjiawan <adhirramjiawan0@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1541) corrects a small mistake in ehci-hcd. The IAAD
(Interrupt on Async Advance Doorbell) bit in the USBCMD register is
designed, as its name says, to act as a "doorbell". That is, the
driver activates the bit by setting it to 1, and the hardware
deactivates it later by setting it back to 0. The driver cannot clear
the bit by writing a 0 to it; such writes are simply ignored.
Therefore there is no reason for ehci-hcd to try to clear the bit.
The patch removes the two instances where such attempts occur.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support to configure the SPEAr EHCI & OHCI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds clock gating to suspend and resume functions.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In devices using ehci-sh, initialization of the PHY may be necessary.
This adds platform data to ehci-sh and provide function to initialize PHY.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Shimoda, Yoshihiro <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
release_firmware() tests for a NULL pointer, so it's redundant to do
that checking before calling it.
Additionally, in ene_load_bincode(), 'sd_fw' is a local variable so
setting it to NULL just before it goes out of scope is completely
pointless, so remove that assignment.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Re-arranged EHCI generic and tegra specific functions
into two separate groups for more readability.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After packetize_urb was called, we could still run into an error path
and will not hand over the prepared qtd to the qtd_list. Make sure to
free the prepared qtd in that case to avoid memory leaks.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that dequeued urbs get handled first
by collect_qtds. To achieve that we better move them
up to the head in the qh list.
This for instance fixes hanging serial devices, which wait
for dequeued urbs to properly close their device node.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DEBUG is defined, the kmem_cache_create call a
WARN_ON if the name of the cache uses a space.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this patch, the prepared disable routines
will not be called on module unloading.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for ULPI and UTMI PHYs based on usb controller
version info read from device-tree
Example of USB Controller versioning info:
Version 1.2 and below : MPC8536, MPC8315, etc
Version 1.6 : P1020, P1010, P2020, P5020, etc
Version 2.2 : PSC9131, PSC9132, P3060, etc
No changes for non-DT users
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It displays wrong debug message if we plug in a full/low
speed device at port for builtin TT controller. We can get
device/port speed information at following code of hub_port_init,
so it is better to replace it with debug message of "reset complete".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch:
1. Renamed structure and function names to be more meaningful.
2. Removed unnecessary local variables.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is now replaced by the new ssb USB driver, which also supports
devices with an EHCI controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a USB driver using the generic platform device driver for the
USB controller found on the Broadcom ssb bus. The ssb bus just
exposes one device which serves the OHCI and the EHCI controller at the
same time. This driver probes for this USB controller and creates and
registers two new platform devices which will be probed by the new
generic platform device driver. This makes it possible to use the EHCI
and the OCHI controller on the ssb bus at the same time.
The old ssb OHCI USB driver will be removed in the next step as this
driver also provide an OHCI driver and an EHCI for the cores supporting
it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
