This patch reads charge delay from tsc DT node and writes to
REG_CHARGEDELAY register. If the charge delay is not specified in DT then
default value of 0x400(CHARGEDLY_OPENDLY) is used.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
TSC interrupt handler had udelay to avoid reporting of false pen-up
interrupt to user space. This patch implements workaround suggesting in
Advisory 1.0.31 of silicon errata for am335x, thus eliminating udelay and
touchscreen lag. This also improves performance of touchscreen and
eliminates sudden jump of cursor at touch release.
IDLECONFIG and CHARGECONFIG registers are to be configured with same values
in order to eliminate false pen-up events. This workaround may result in
false pen-down to be detected, hence considerable charge step delay needs
to be added. The charge delay is set to 0xB000 (in terms of ADC clock
cycles) by default.
TSC steps are disabled at the end of every sampling cycle and EOS bit is
set. Once the EOS bit is set, the TSC steps need to be re-enabled to begin
next sampling cycle.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch makes the initial changes required to workaround TSC-false
pen-up interrupts. It is required to implement these changes in order to
remove udelay in the TSC interrupt handler and false pen-up events. The
charge step is to be executed immediately after sampling X+. Hence TSC is
made to use higher numbered steps (steps 5 to 16 for 5 co-ordinate
readouts, 4 wire TSC configuration) and ADC to use lower ones. Further X
co-ordinate readouts must be the last to be sampled, thus co-ordinates are
sampled in the order Y-Z-X.
Signed-off-by: Brad Griffis <bgriffis@ti.com>
[vigneshr@ti.com: Ported the patch from v3.12 to v3.19rc1]
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer updates from Dmitry Torokhov:
"Just a few quirks for PS/2 this time"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add more Fujtisu notebooks to force crc_enabled
Input: i8042 - add noloop quirk for Medion Akoya E7225 (MD98857)
Input: synaptics - adjust min/max for Lenovo ThinkPad X1 Carbon 2nd
Add two more Fujitsu LIFEBOOK models that also ship with the Elantech
touchpad and don't work with crc_disabled to the quirk list.
Signed-off-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices are not fast enough to differentiate between a fast-moving
contact and a new contact. This problem cannot be fully resolved because
information is truly missing, but it is possible to safe-guard against
obvious mistakes by restricting movement with a maximum displacement.
The new problem formulation for dmax > 0 cannot benefit from the speedup
for positive definite matrices, but since the convergence is faster, the
result is about the same. For a handful of contacts, the latency difference
is truly negligible.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a I2C driver, so it's wrong to use platform prefix for the
modalias. We have all needed i2c aliases coming form MODULE_DEVICE_TABLE,
so let's remove the wrong and unneeded drv2667-haptics modalias.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a I2C driver, so it's wrong to use platform prefix for the
modalias. We have all needed i2c aliases coming form MODULE_DEVICE_TABLE,
so let's remove the wrong and unneeded drv260x-haptics modalias.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a I2C driver, so it's wrong to use platform prefix for the
modalias. We have all needed i2c aliases coming form MODULE_DEVICE_TABLE,
so let's remove the wrong and unneeded cap11xx modalias.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Daniel Mack <linux@zonque.org>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Allwinner A31 SoC (sun6i) has the same resistive touchpanel controller
as on other sunxi platforms. The only difference between the variants is
the control bits for enabling operations are left-shifted by 1 on the A31.
Also update the comment for the original temperature sensor with
information from Allwinner.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver implements support for PS2 controller found on Allwinner A10,
A20 SOCs. It has been tested on A20 Olimex-Lime2 board and also on A10.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To allow for different firmware sizes let's replace the original size check
with with checking the signature in the firmware data.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The fixes to the X.org driver have been applied long time ago and
the patch on kernel.org has long since gone so let's remove the
comment.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Without this the aux port does not get detected, and consequently the touchpad
will not work.
With this patch the touchpad is detected:
$ dmesg | grep -E "(SYN|i8042|serio)"
pnp 00:03: Plug and Play ACPI device, IDs SYN1d22 PNP0f13 (active)
i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd00123/0x840300/0x126800, board id: 2863, fw id: 1473085
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6
dmidecode excerpt for this laptop is:
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: Medion
Product Name: Akoya E7225
Version: 1.0
Cc: stable@vger.kernel.org
Signed-off-by: Jochen Hein <jochen@jochen.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If "(count == NAME_MAX)" then we could end up putting the NUL terminator
one space beyond the end of the fw_name[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the warning regarding variable being dereferenced before check
'gen5_pip->resp_len'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gen5_bl_metadata_row_params structure has its fields specified with
explicit endianness, so we should not be trying to convert to native CPU
endianness when filling the structure.
Also fix firmware validation checks and misspelled field in
gen5_bl_metadata_row_params.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Dudley Du <dudl@cypress.com>
Tested-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem fixes from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: uinput - fix ioctl nr overflow for UI_GET_SYSNAME/VERSION
Input: I8042 - add Acer Aspire 7738 to the nomux list
Input: elantech - support new ICs types for version 4
Input: i8042 - reset keyboard to fix Elantech touchpad detection
MAINTAINERS: remove Dmitry Torokhov's alternate address
Add acpi device tree support.
acpi device id "CYAP0000" is for old gen3 trackpad devices.
acpi device id "CYAP0001" is for new gen5 trackpad devices.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add force re-calibrate function support for gen5 trackpad device, it can be
used through sysfs calibrate interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add read baseline function support for gen5 trackpad device, it can be used
through sysfs baseline interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add firmware image update support for gen5 trackpad device, it can be used
through sysfs update_fw interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add force re-calibrate function support for gen3 trackpad device, it can be
used through sysfs calibrate interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add read baseline function supported for gen3 trackpad device, it can be
used through sysfs baseline interface.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for firmware image update for gen3 trackpad devices; the
firmware update is initiated by writing to update_fw sysfs attribute.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Introduce control interfaces that are commonly used in pre- and after
production, for trackpad device state checking, managing and firmware image
updating. These interfaces include mode, firmware_version and product_id
interfaces for reading firmware version and trackpad device product id
values, and update_fw interface to command firmware image update process.
There are also baseline and calibrate interfaces for reading and checking
trackpad device's sensors states.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change implements runtime PM support in the driver and adds
runtime_suspend_scanrate_ms power management interface in device's power
group, so users or applications can control the runtime power management
strategy of trackpad device according to their requirements.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add suspend_scanrate_ms power management interfaces in device's
power group, so users or applications can control the power management
strategy of trackpad device according to their requirements.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds support for Gen5 Cypress trackpads. The driver detects
generation of the device at probe time and automatically selects
appropriate protocol.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to support multiple different chipsets and communication protocols
trackpad devices in one cyapa driver, the new cyapa driver is re-designed
with one cyapa driver core and multiple device specific functions component.
The cyapa driver core is contained in this patch, it supplies basic functions
that working with kernel and input subsystem, and also supplies the interfaces
that the specific devices' component can connect and work together with as
one driver.
Signed-off-by: Dudley Du <dudl@cypress.com>
Tested-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen controller has a temperature sensor embedded in the SoC,
which already has hwmon support in the driver.
Add DT thermal zone support so we can use it with cpufreq for thermal
throttling.
This also adds a comment stating that we do not know the actual formula
for calculating the temperature.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUsuDQAAoJEHm+PkMAQRiGnecH/0RO9UKnEduOTRPaZGXAjGI8
N0FvNia8qn7f+XnvN62pG/YZZqi2uvuy37vwAXMtS6KXEgaDG9Wq4fVrhOaJ5VgL
QOmPdVGUa+1PuPcMYj/QLIFRfIHvIY/XVZWXrcIyYfQdBAAoJ2q23qx/yFmdyTwf
+enAv+PV4ZVNMEANyN9KS7xX5gPbSDl36AOhm6lXDvrlem4mbnhRuUtYez9R8KTK
VNfkKZQRDOgl4/ns0ndzpAUhaDj1JJGoLRgMXKna33XgtzSEL4XijvImdnoIXp5N
Z98Jc1N5Vg5OcUFeGJC3bRR27m39xoOHQk2ufY43uAIfB3Ez/C7m/r7b50ZVWfs=
=J7TO
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rc4' into next
Merge with mainline to bring in the latest thermal and other changes.
When client changes the type of clock used for the time stamps in input
events flush pending events from the client's queue (since client would not
know which events have old time stamps and which ones have new ones) and
and queue SYN_DROPPED event.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure that driver does not process bogus packets as trackstick data
when there is no trackstick present and emit warnings in dmesg so potential
issues with trackstick handling will be visible for debugging.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change fixes name, product and version of dev2 input device based on
format used in function psmouse_switch_protocol() in file psmouse-base.c.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All the use cases in this driver has a regulator_haptic_toggle() call after
regulator_haptic_set_voltage(). So make regulator_haptic_set_voltage() call
regulator_haptic_toggle() to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When KBC is in active multiplexing mode the touchpad on this laptop does
not work.
Reported-by: Bilal Koc <koc.bilo@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of registering device attributes individually let's use attribute
groups and also devm_* infrastructure to ease cleanup.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds support for the Power Enable Key found on MFD AXP202
and AXP209. Besides the basic support for the button, the driver adds
two entries in sysfs to configure the time delay for power on/off.
Signed-off-by: Carlo Caione <carlo@caione.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[wens@csie.org: made axp20x_pek_remove() static; removed driver owner
field; fixed path for sysfs entries]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If given input handler is not a filter there is no point is iterating list
of events in a packet to see if some of them need to be filtered out.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a device does not support autorepeat or does not emit any key events we
should not be scanning all events in a packet to decide if we should start
or stop autorepeat function.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change allows the driver to recognize newer Elantech touchpads.
Cc: stable@vger.kernel.org
Signed-off-by: Yi ju Hong <sam.hung@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some laptops, keyboard needs to be reset in order to successfully detect
touchpad (e.g., some Gigabyte laptop models with Elantech touchpads).
Without resettin keyboard touchpad pretends to be completely dead.
Based on the original patch by Mateusz Jończyk this version has been
expanded to include DMI based detection & application of the fix
automatically on the affected models of laptops. This has been confirmed to
fix problem by three users already on three different models of laptops.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81331
Cc: stable@vger.kernel.org
Signed-off-by: Srihari Vijayaraghavan <linux.bug.reporting@gmail.com>
Acked-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Tested-by: Srihari Vijayaraghavan <linux.bug.reporting@gmail.com>
Tested by: Zakariya Dehlawi <zdehlawi@gmail.com>
Tested-by: Guillaum Bouchard <guillaum.bouchard@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Documentation/CodingStyle - Chapter 14:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."
So do it as recommended.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fixes from Dmitry Torokhov:
"Fixes for v7 protocol for ALPS devices and few other driver fixes.
Also users can request input events to be stamped with boot time
timestamps, in addition to real and monotonic timestamps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: hil_kbd - fix incorrect use of init_completion
Input: alps - v7: document the v7 touchpad packet protocol
Input: alps - v7: fix finger counting for > 2 fingers on clickpads
Input: alps - v7: sometimes a single touch is reported in mt[1]
Input: alps - v7: ignore new packets
Input: evdev - add CLOCK_BOOTTIME support
Input: psmouse - expose drift duration for IBM trackpoints
Input: stmpe - bias keypad columns properly
Input: stmpe - enforce device tree only mode
mfd: stmpe: add pull up/down register offsets for STMPE
Input: optimize events_per_packet count calculation
Input: edt-ft5x06 - fixed a macro coding style issue
Input: gpio_keys - replace timer and workqueue with delayed workqueue
Input: gpio_keys - allow separating gpio and irq in device tree
synaptics_profile_sensor_process() and synaptics_report_mt_data() now
share the exact same code. Remove one implementation and rely on the
other where it was used.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current code tries to consider all states and transitions to properly
detect which finger is attached to which slot. The code is quite huge
and difficult to read.
If the sensor manages to group the touch points but is not reliable in
giving tracking ids, we can simply use the kernel tracking method. Note
that it is already used by Cr-48 Chromebooks.
Incidentaly, this fixes a bug reported by Peter Hutterer:
"""
on the Lenovo T440, run:
evemu-record /dev/input/event4 | grep BTN_
then put one, two, three, two fingers down
when you go from 3 to 2 fingers the driver sends a spurious BTN_TOUCH 0
event:
E: 0.000000 0001 014a 0001 # EV_KEY / BTN_TOUCH 1
E: 0.000000 0001 0145 0001 # EV_KEY / BTN_TOOL_FINGER 1
E: 0.770008 0001 0145 0000 # EV_KEY / BTN_TOOL_FINGER 0
E: 0.770008 0001 014d 0001 # EV_KEY / BTN_TOOL_DOUBLETAP 1
E: 1.924716 0001 014d 0000 # EV_KEY / BTN_TOOL_DOUBLETAP 0
E: 1.924716 0001 014e 0001 # EV_KEY / BTN_TOOL_TRIPLETAP 1
.. changing from 3 to 2 fingers now
E: 3.152641 0001 014a 0000 # EV_KEY / BTN_TOUCH 0
E: 3.152641 0001 014d 0001 # EV_KEY / BTN_TOOL_DOUBLETAP 1
E: 3.152641 0001 014e 0000 # EV_KEY / BTN_TOOL_TRIPLETAP 0
E: 3.176948 0001 014a 0001 # EV_KEY / BTN_TOUCH 1
quick look in the kernel shows it's caused by hw.z going to 0 for a packet,
so probably a firmware bug. either way, it makes it hard to track BTN_TOUCH
as signal that at least one finger is down.
"""
The in-kernel tracking is enough to remove this spurious BTN_TOUCH 0.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Most of the protocol for these touchpads has been reverse engineered. This
commit adds a basic multitouch-capable driver.
A lot of the protocol is still unknown. Especially, we don't know how to
identify the device yet apart from the PNP ID.
The previous workaround for these devices has been left in place in case
the driver is not compiled into the kernel or in case some other device
with the same PNP ID is not recognized by the driver yet still has the same
problems with the device probing code.
Signed-off-by: Mathias Gottschlag <mgottschlag@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The successive init_completion calls should be reinit_completion calls.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With this driver, we can report KEY_POWER on AM437x SK. This patch has been
tested with said board.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Allwinnner sunxi SoCs have a low resolution adc (called lradc) which is
specifically designed to have various (tablet) keys (ie home, back, search,
etc). attached to it using a resistor network. This adds a driver for this.
There are 2 channels, currently this driver only supports chan0 since there
are no boards known to use chan1.
This has been tested on an olimex a10s-olinuxino-micro, a13-olinuxino, and
a20-olinuxino-micro.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change adds support for haptic driver controlled by voltage of a
regulator. Userspace can control the device via Force Feedback interface
from input framework.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyunhee Kim <hyunhee.kim@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a table documenting where all the bits are in the v7 touchpad packets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Protocol v7 uses the middle / right button bits on clickpads to communicate
"location" information of a 3th touch (and possible 4th) touch on
clickpads.
Specifically when 3 touches are down, if one of the 3 touches is in the
left / right button area, this will get reported in the middle / right
button bits and the touchpad will still send a TWO type packet rather then
a MULTI type packet, so when this happens we must add the finger reported
in the button area to the finger count.
Likewise we must also add fingers reported this way to the finger count
when we get MULTI packets.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=86338
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The v7 proto differentiates between a primary touch (with high precision)
and a secondary touch (with lower precision). Normally when 2 fingers are
down and one is lifted the still present touch becomes the primary touch,
but some traces have shown that this does not happen always.
This commit deals with this by making alps_get_mt_count() not stop at the
first empty mt slot, and if a touch is present in mt[1] and not mt[0]
moving the data to mt[0] (for input_mt_assign_slots).
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=86338
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
NEW packets are send to indicate a discontinuity in the finger coordinate
reporting. Specifically a finger may have moved from slot 0 to 1 or vice
versa. INPUT_MT_TRACK takes care of this for us.
NEW packets have 3 problems:
1) They do not contain middle / right button info (on non clickpads)
this can be worked around by preserving the old button state
2) They do not contain an accurate fingercount, and they are
typically send when the number of fingers changes. We cannot use
the old finger count as that may mismatch with the amount of
touch coordinates we've available in the NEW packet
3) Their x data for the second touch is inaccurate leading to
a possible jump of the x coordinate by 16 units when the first
non NEW packet comes in
Since problems 2 & 3 cannot be worked around, just ignore them.
BugLink: https://bugs.freedesktop.org/show_bug.cgi?id=86338
Cc: stable@vger.kernel.org # 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds support for CLOCK_BOOTTIME for input event timestamp.
CLOCK_BOOTTIME includes suspend time, so it would allow aplications
to get correct time difference between two events even when system
resumes from suspend state.
Signed-off-by: Aniroop Mathur <a.mathur@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
IBM Trackpoints have a feature to compensate for drift by recalibrating
themselves periodically. By default, if for 0.5 seconds there is no change
in position, it's used as the new zero. This duration is too low. Often,
the calibration happens when the trackpoint is in fact being used.
IBM's Trackpoint Engineering Specifications show a configuration register
that allows changing this duration, rstdft1.
Expose it via sysfs among the other settings.
Signed-off-by: Mike Murdoch <main.haarp@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"Two new drivers for Elan hardware (for I2C touchpad and touchscreen
found in several Chromebooks and other devices), a driver for Goodix
touch panel, and small fixes to Cypress I2C trackpad and other input
drivers.
Also we switched to use __maybe_unused instead of gating suspend/
resume code with #ifdef guards to get better compile coverage"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (27 commits)
Input: gpio_keys - fix warning regarding uninitialized 'button' variable
Input: add support for Elan eKTH I2C touchscreens
Input: gpio_keys - fix warning regarding uninitialized 'irq' variable
Input: cyapa - use 'error' for error codes
Input: cyapa - fix resuming the device
Input: gpio_keys - add device tree support for interrupt only keys
Input: amikbd - allocate temporary keymap buffer on the stack
Input: amikbd - fix build if !CONFIG_HW_CONSOLE
Input: lm8323 - missing error check in lm8323_set_disable()
Input: initialize device counter variables with -1
Input: initialize input_no to -1 to avoid subtraction
Input: i8042 - do not try to load on Intel NUC D54250WYK
Input: atkbd - correct MSC_SCAN events for force_release keys
Input: cyapa - switch to using managed resources
Input: lifebook - use "static inline" instead of "inline" in lifebook.h
Input: touchscreen - use __maybe_unused instead of ifdef around suspend/resume
Input: mouse - use __maybe_unused instead of ifdef around suspend/resume
Input: misc - use __maybe_unused instead of ifdef around suspend/resume
Input: cap11xx - support for irq-active-high option
Input: cap11xx - add support for various cap11xx devices
...
All keypad column pins used as inputs should be pulled up on the STMPE24xx,
but this is not done by the current driver. Add some logic that will do
this properly. The STMPE1601 also has a keypad controller, but explicitly
does *NOT* require you to set up any pull-ups.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The STMPE keypad controller is only used with device tree configured
systems, so force the configuration to come from device tree only, and now
actually get the rows and cols from the device tree too.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch avoids unnecessary operations while estimating events per
packet for an input device when event type is not set.
Signed-off-by: Anshul Garg <anshul.g@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixed a coding style error, macros with complex values should be
enclosed in parentheses.
Signed-off-by: Asaf Vertz <asaf.vertz@tandemg.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We do not need to roll our own implementation of delayed work now that we
have proper implementation of mod_delayed_work.
For interrupt-only driven buttons we retain the timer, but we rename
it to release_timer to better reflect its purpose.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change allows specify interrupt for buttons separately form gpio,
potentially allowing to form several "clusters" of buttons on
different interrupts.
Button defined without both gpio and irq in device tree is a hared error
instead of a warning now.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Commit af906faabc ("Input: gpio_keys - fix warning regarding uninitialized
'irq' variable") introduced the following build warning:
drivers/input/keyboard/gpio_keys.c:625:16: warning: 'button' may be used uninitialized in this function [-Wmaybe-uninitialized]
Move the 'button' initialization to a proper location to avoid such warning.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* device-properties:
leds: leds-gpio: Fix multiple instances registration without 'label' property
leds: leds-gpio: Fix legacy GPIO number case
ACPI / property: Drop size_prop from acpi_dev_get_property_reference()
leds: leds-gpio: Convert gpio_blink_set() to use GPIO descriptors
ACPI / GPIO: Document ACPI GPIO mappings API
net: rfkill: gpio: Add default GPIO driver mappings for ACPI
ACPI / GPIO: Driver GPIO mappings for ACPI GPIOs
input: gpio_keys_polled: Make use of device property API
leds: leds-gpio: Make use of device property API
gpio: Support for unified device properties interface
Driver core: Unified interface for firmware node properties
input: gpio_keys_polled: Add support for GPIO descriptors
leds: leds-gpio: Add support for GPIO descriptors
gpio: sch: Consolidate core and resume banks
gpio / ACPI: Add support for _DSD device properties
misc: at25: Make use of device property API
ACPI: Allow drivers to match using Device Tree compatible property
Driver core: Unified device properties interface for platform firmware
ACPI: Add support for device specific properties
This driver supports Elan eKTH I2C touchscreen controllers. Note that these
are using custom protocol, as opposed to other Elan parts that use
HID-over-I2C and are supported by the standard HID-multitouch driver.
Signed-off-by: Scott Liu <scott.liu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit f2d347ff70 ("Input: gpio_keys - add device tree support for
interrupt only keys") caused the following build warning:
drivers/input/keyboard/gpio_keys.c: In function 'gpio_keys_probe':
drivers/input/keyboard/gpio_keys.c:647:15: warning: 'irq' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/input/keyboard/gpio_keys.c:622:7: note: 'irq' was declared here
Move button->irq initialization into proper branch and get rid of the
temporary.
Reported-by: Olof's autobuilder <build@lixom.net>
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
The alternative of CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME may be
replaced with CONFIG_PM too.
Make these changes in 2 files under drivers/input/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's use 'error' variable instead of 'ret' when we need to store erro
codes.
Signed-off-by: Dudley Du <dudley.dulixin@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Chage b1cfa7b438 tried to get away form using
irq in cyapa structure and use client->irq instead, but missed a couple of
spots making the touchpad inoperative after resume.
Reported-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Dudley Du <dudley.dulixin@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This features already exists for board config setups. Add support for
device tree based systems.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Allocate the temporary buffer needed for initialization of the console
keyboard maps (512 bytes, as NR_KEYS = 256) on the stack instead of
statically, to reduce kernel size.
add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-512 (-512)
function old new delta
temp_map 512 - -512
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If CONFIG_HW_CONSOLE is not set:
drivers/built-in.o: In function `amikbd_probe':
amikbd.c:(.init.text+0x3e4e): undefined reference to `key_maps'
amikbd.c:(.init.text+0x3dd4): undefined reference to `key_maps'
To fix this, extract the initialization of the console keyboard maps
into amikbd_init_console_keymaps(), protected by #ifdef
CONFIG_HW_CONSOLE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The missing error handling here is not especially harmful but static
checkers complain that "i" can be used uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's initialize atomic_t variables keeping track of number of various
devices created so far with -1 in order to avoid extra subtraction
operation.
Signed-off-by: Aniroop Mathur <aniroop.mathur@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If kzalloc() failed and then evdev_open_device() fails, evdev_open()
will pass a vmalloc'ed pointer to kfree.
This might fix https://bugzilla.kernel.org/show_bug.cgi?id=88401, where
there was a crash in kfree().
Reported-by: Christian Casteyde <casteyde.christian@free.fr>
Belatedly-Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let's initializes input_no to -1 in order to avoid extra subtraction
operation performed every time we allocate an input device.
Signed-off-by: Aniroop Mathur <aniroop.mathur@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Intel NUC D54250WYK has no PS/2 controller, however the DSDT declares
PS/2 devices which trigger the loading of the i8042 driver.
Signed-off-by: Todor Minchev <todor.minchev@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fixes from Dmitry Torokhov:
"The main change is to fix breakage in Elantech driver introduced by
the recent commit adding trackpoint reporting to protocol v4. Now we
are trusting the hardware to advertise the trackpoint properly and do
not try to decode the data as trackpoint if firmware told us it is not
present"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - use proper endpoint type
Input: elantech - trust firmware about trackpoint presence
Input: synaptics - adjust min/max on Thinkpad E540
The xpad wireless endpoint is not a bulk endpoint on my devices, but
rather an interrupt one, so the USB core complains when it is submitted.
I'm guessing that the author really did mean that this should be an
interrupt urb, but as there are a zillion different xpad devices out
there, let's cover out bases and handle both bulk and interrupt
endpoints just as easily.
Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Only try to parse data as coming from trackpoint if firmware told us that
trackpoint is present.
Fixes commit caeb0d37fa
Reported-and-tested-by: Marcus Overhagen <marcus.overhagen@gmail.com>
Reported-and-tested-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Without the change either no scancode would be reported on release of
force_release keys, or - if the key is marked as force_release erroneously
- the release event and the scancode would be reported in separate reports
to the input layer.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The LEN2006 Synaptics touchpad (as found in Thinkpad E540) returns wrong
min max values.
touchpad-edge-detector output:
> Touchpad SynPS/2 Synaptics TouchPad on /dev/input/event6
> Move one finger around the touchpad to detect the actual edges
> Kernel says: x [1472..5674], y [1408..4684]
> Touchpad sends: x [1264..5675], y [1171..4688]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88211
Cc: stable@vger.kernel.org
Signed-off-by: Binyamin Sagal <bensagal@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"Mostly small fixups to PS/2 tochpad drivers (ALPS, Elantech,
Synaptics) to better deal with specific hardware"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - update the documentation
Input: elantech - provide a sysfs knob for crc_enabled
Input: elantech - report the middle button of the touchpad
Input: alps - ignore bad data on Dell Latitudes E6440 and E7440
Input: alps - allow up to 2 invalid packets without resetting device
Input: alps - ignore potential bare packets when device is out of sync
Input: elantech - fix crc_enabled for Fujitsu H730
Input: elantech - use elantech_report_trackpoint for hardware v4 too
Input: twl4030-pwrbutton - ensure a wakeup event is recorded.
Input: synaptics - add min/max quirk for Lenovo T440s
The detection of crc_enabled is known to fail for Fujitsu H730. A DMI
blacklist is added for that, but it can be expected that other laptops will
pop up with this.
Here a sysfs knob is provided to alter the behaviour of crc_enabled.
Writing 0 or 1 to it sets the variable to 0 or 1. Reading it will show the
crc_enabled variable (0 or 1).
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the past, no elantech was known with 3 touchpad mouse buttons.
Fujitsu H730 is the first known elantech with a middle button. This commit
enables this middle button. For backwards compatibility, the Fujitsu is
detected via DMI, and only for this one 3 buttons will be announced.
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sometimes on Dell Latitude laptops psmouse/alps driver receive invalid ALPS
protocol V3 packets with bit7 set in last byte. More often it can be
reproduced on Dell Latitude E6440 or E7440 with closed lid and pushing
cover above touchpad.
If bit7 in last packet byte is set then it is not valid ALPS packet. I was
told that ALPS devices never send these packets. It is not know yet who
send those packets, it could be Dell EC, bug in BIOS and also bug in
touchpad firmware...
With this patch alps driver does not process those invalid packets, but
instead of reporting PSMOUSE_BAD_DATA, getting into out of sync state,
getting back in sync with the next byte and spam dmesg we return
PSMOUSE_FULL_PACKET. If driver is truly out of sync we'll fail the checks
on the next byte and report PSMOUSE_BAD_DATA then.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use of managed resources simplifies error handling and device removal code.
Signed-off-by: Dudley Du <dudl@cypress.com>
[Dmitry: added open/close methods so cyapa_remove is no longer needed.]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For functions defined in header files we should use static inline rather
than inline, which breaks under the latest upstream gcc (which is really
gcc issue, but static inline is better suited regardless).
The related error (with allmodconfig under tile):
MODPOST 4002 modules
ERROR: "lifebook_detect" [drivers/input/mouse/psmouse.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some Dell Latitude laptops ALPS device or Dell EC send one invalid byte
in 6 bytes ALPS packet. In this case psmouse driver enter out of sync
state. It looks like that all other bytes in packets are valid and also
device working properly. So there is no need to do full device reset, just
need to wait for byte which match condition for first byte (start of
packet). Because ALPS packets are bigger (6 or 8 bytes) default limit is
small.
This patch increase number of invalid bytes to size of 2 ALPS packets which
psmouse driver can drop before do full reset.
Resetting ALPS devices take some time and when doing reset on some Dell
laptops touchpad, trackstick and also keyboard do not respond. So it is
better to do it only if really necessary.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
5th and 6th byte of ALPS trackstick V3 protocol match condition for first
byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS
trackstick is sending data then driver match 5th, 6th and next 1st bytes as
PS/2.
It basically means if user is using trackstick when driver is in out of
sync state driver will never resync. Processing these bytes as 3 bytes PS/2
data cause total mess (random cursor movements, random clicks) and make
trackstick unusable until psmouse driver decide to do full device reset.
Lot of users reported problems with ALPS devices on Dell Latitude E6440,
E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send
some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like
that i8042 and psmouse/alps driver always receive group of 6 bytes packets
so there are no missing bytes and no bytes were inserted between valid
ones.
This patch does not fix root of problem with ALPS devices found in Dell
Latitude laptops but it does not allow to process some (invalid)
subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of
sync.
So with this patch trackstick input device does not report bogus data when
also driver is out of sync, so trackstick should be usable on those
machines.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Fujitsu H730 does not work with crc_enabled = 0, even though the
crc_enabled bit in the firmware version indicated it would. When switching
this value to crc_enabled to 1, the touchpad works. This patch uses DMI to
detect H730.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Fujitsu H730 has hardware v4 with a trackpoint. This enables the
elantech_report_trackpoint for v4.
Reported-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Stefan Valouch <stefan@valouch.com>
Tested-by: Alfredo Gemma <alfredo.gemma@gmail.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This button is treated as a wakeup source, so we need to initialise it
correctly.
Without the device_init_wakeup() call, dev->power.wakeup will
be NULL, and pm_wakeup_event() will do nothing.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The new Lenovo T440s laptop has a different PnP ID "LEN0039", and it
needs the similar min/max quirk to make its clickpad working.
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=903748
Reported-and-tested-by: Joschi Brauchle <joschibrauchle@gmx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make use of device property API in this driver so that both OF based
system and ACPI based system can use this driver.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
GPIO descriptors are the preferred way over legacy GPIO numbers
nowadays. Convert the driver to use GPIO descriptors internally but
still allow passing legacy GPIO numbers from platform data to support
existing platforms.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use __maybe_unused instead of ifdef guards around suspend/resume
functions, in order to increase build coverage and fix build warnings.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some applications need to use the irq-active-high push-pull option.
This allows it be enabled in the device tree child node.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are variants of the cap11xx device with a varying number of
capacitance detection channels.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are several devices in cap11xx family besides cap1106. The driver can
be made to support all of them, so let's give it more generic name.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
Use them devm_ managed resources API to simplify error handling in
altera_ps2_probe() and to reduce the size of altera_ps2_remove() and the
ps2if struct.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a driver for the Goodix touchscreen panel found in Onda v975w tablets.
The driver is based off the Android driver gt9xx.c found in some Android
code dumps, but now bears no resemblance to the original driver.
The driver was tested on the aforementioned tablet.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 68da166491.
It turns out that the assertion about scope of regressions due to
always keeping keyboard controller in legacy mode was proven wrong.
There are laptops, such as Clevo W650SH, that only have internal
touchpad (no external PS/2 ports), that require active multiplexing
mode to switch the touchpad (Elantech) into native mode instead of
basic PS/2 emulation.
Reported-by: Roel Aaij <roel.aaij@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The irq function altera_ps2_rxint returns an irqreturn_t, so use the
same type for variable storing the return value.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In altera_ps2_close, the data register (offset 0) is written instead of
the control register (offset 4), leading to the RX interrupt not being
disabled. Fix this by calling writel() with the offset for the proper
register.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Expression haptic->pwm_dev->period * haptic->magnitude is of type
'unsigned int' and may overflow. We need to convert one of the operands
to u64 before multiplying, instead of casting result (potentially
overflown) to u64.
Reported by Coverity: CID 1248753
Acked-by : Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
psmouse_reconnect() will not be called if psmouse driver is not bound to
the serio port, so there is no point in checking that. Also, as coded, it
introduces potential NULL dereference in psmouse_dbg() in case psmouse is
indeed NULL. Let's just remove it.
Detected by Coverity: CID 146528
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I believe the intent of the code was to drop oldest bytes from the queue,
not the latest if we drop one byte and both latest and some oldest of we
are dropping more than one.
Acked-by: Jan-Benedict Glaw <jbglaw@lug-owl.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Coverity pointed out that at return point error is always 0 so the
conditional is not needed.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sharp SL-6000 (tosa) touchscreen needs wider limits to properly map all
points on the screen. Expand ranges in abs_x and abs_y arrays according
to the touchscreen area.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bitmask comment says it will enable GPIO 8-14 and 16-20 for keypad use,
but it actually enables GPIO 8-11 and 13-20 due to a bit error.
Instead of masking of the "hole" at GPIO 12 (which is used for keypad
output 4) mask of the proper "hole" at GPIO 15.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the new flags argument to calls of (devm_)gpiod_get*().
Currently both forms (with or without the flags argument) are valid thanks
to transitional macros in <linux/gpio/consumer.h>. These macros will be
removed once all consumers are updated and the flags argument will become
compulsory.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver supports Elan I2C/SMbus touchpads found in some laptops and
also in many Chromebooks.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change switches to using devm_* managed resources APIs to
request the resources in probe to simplify probe error path and
module unloading.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change switches ithe driver to use devm_* APIs to allocate resources.
This helps to simplify failure path in probe function and module unloading
and does away with remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change switches the driver to use devm_* managed resources APIs to
request the resources in probe to simplify probe error path and module
unloading and does away with remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull second round of input updates from Dmitry Torokhov:
"Mostly simple bug fixes, although we do have one brand new driver for
Microchip AR1021 i2c touchscreen.
Also there is the change to stop trying to use i8042 active
multiplexing by default (it is still possible to activate it via
i8042.nomux=0 on boxes that implement it)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add Thrustmaster as Xbox 360 controller vendor
Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
Input: max77693-haptic - fix state check in imax77693_haptic_disable()
Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
Input: alps - fix v4 button press recognition
Input: i8042 - disable active multiplexing by default
Input: i8042 - add noloop quirk for Asus X750LN
Input: synaptics - gate forcepad support by DMI check
Input: Add Microchip AR1021 i2c touchscreen
Input: cros_ec_keyb - add of match table
Input: serio - avoid negative serio device numbers
Input: avoid negative input device numbers
Input: automatically set EV_ABS bit in input_set_abs_params
Input: adp5588-keys - cancel workqueue in failure path
Input: opencores-kbd - switch to using managed resources
Input: evdev - fix EVIOCG{type} ioctl
Add Thrustmaster as Xbox 360 controller vendor. This is required for
example to make the GP XID (044f:b326) gamepad work.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the USB ID for the Xbox 360 Thrustmaster Ferrari 458 Racing Wheel.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The check to see whether the device is already disabled in
max77693_haptic_disable() was inversed, this change corrects it.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
xenkbd_disconnect_backend doesn't free grant table entry. This bug affects
live migration.
xenkbd_disconnect_backend uses gnttab_end_foreign_access_ref to handle
grant table entry which doesn't really free an entry.
Thus every time we do xenkbd_resume, grant table entry increses by one. As
an grant table entry occupies 8 bytes, an grant table page has at most 512
entries. Every 512 times we do xenkdb_resume, grant table pages increses by
one.
After around 3500 times of live migration, grant table pages will increase
by 7, causing too many pages to populate and hitting max_pages limit when
assigning pages.Thus assign_pages will fail, so will live migration.
Signed-off-by: Chang Huaixin <huaixin.chx@alibaba-inc.com>
Acked-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since the change to struct input_mt_pos some variables are now bitfields
instead of integers. Automatic conversion from integer to bitfield entry
destroys information, therefore enforce boolean interpretation instead.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1114768
Fixes: 02d04254a5 ("Input: alps - use struct input_mt_pos to track coordinates")
Signed-off-by: Andreas Bosch <linux@progandy.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xxsZ
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Changes to existing drivers:
- DT clean-ups in da9055-core, max14577, rn5t618, arizona, hi6421, stmpe, twl4030
- Export symbols for use in modules in max14577
- Plenty of static code analysis/Coccinelle fixes throughout the SS
- Regmap clean-ups in arizona, wm5102, wm5110, da9052, tps65217, rk808
- Remove unused/duplicate code in da9052, 88pm860x, ti_ssp, lpc_sch, arizona
- Bug fixes in ti_am335x_tscadc, da9052, ti_am335x_tscadc, rtsx_pcr
- IRQ fixups in arizona, stmpe, max14577
- Regulator related changes in axp20x
- Pass DMA coherency information from parent => child in MFD core
- Rename DT document files for consistency
- Add ACPI support to the MFD core
- Add Andreas Werner to MAINTAINERS for MEN F21BMC
New drivers/supported devices:
- New driver for MEN 14F021P00 Board Management Controller
- New driver for Ricoh RN5T618 PMIC
- New driver for Rockchip RK808
- New driver for HiSilicon Hi6421 PMIC
- New driver for Qualcomm SPMI PMICs
- Add support for Intel Braswell in lpc_ich
- Add support for Intel 9 Series PCH in lpc_ich
- Add support for Intel Quark ILB in lpc_sch"
[ Delayed to after the poweer/reset pull due to Kconfig problems with
recursive Kconfig select/depends-on chains. - Linus ]
* tag 'mfd-for-linus-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (79 commits)
mfd: cros_ec: wait for completion of commands that return IN_PROGRESS
i2c: i2c-cros-ec-tunnel: Set retries to 3
mfd: cros_ec: move locking into cros_ec_cmd_xfer
mfd: cros_ec: stop calling ->cmd_xfer() directly
mfd: cros_ec: Delay for 50ms when we see EC_CMD_REBOOT_EC
MAINTAINERS: Adds Andreas Werner to maintainers list for MEN F21BMC
mfd: arizona: Correct mask to allow setting micbias external cap
mfd: Add ACPI support
Revert "mfd: wm5102: Manually apply register patch"
mfd: ti_am335x_tscadc: Update logic in CTRL register for 5-wire TS
mfd: dt-bindings: atmel-gpbr: Rename doc file to conform to naming convention
mfd: dt-bindings: qcom-pm8xxx: Rename doc file to conform to naming convention
mfd: Inherit coherent_dma_mask from parent device
mfd: Document DT bindings for Qualcomm SPMI PMICs
mfd: Add support for Qualcomm SPMI PMICs
mfd: dt-bindings: pm8xxx: Add new compatible string
mfd: axp209x: Drop the parent supplies field
mfd: twl4030-power: Use 'ti,system-power-controller' as alternative way to support system power off
mfd: dt-bindings: twl4030-power: Use the standard property to mark power control
mfd: syscon: Add Atmel GPBR DT bindings documention
...
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics and
a slightly buggy strncasecmp. The latter is the POSIX name, so strnicmp
was renamed to strncasecmp, and strnicmp made into a wrapper for the new
strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in the
future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUNonmAAoJEFxbo/MsZsTRHAQH/inCjpCT+pkvTB0YAVfVvgMI
gUogT8G+iB2MuCNpMffGIt8TAVXwcVtnOLH9ABH3IBVehzgipIbIiVEM9YhjrYvU
1rgIKBpmZqSpjDHoIHpdHeCH67cVnRzA/PyoxZWLxPNmQ0t6bNf9yeAcCXK9PfUc
7EAblUDmPGSx9x/EUnOKNNaZSEiUJZHDBXbMBLllk1+5H1vfKnpFCRGMG0IrfI44
KVP2NX9Gfa05edMZYtH887FYyjFe2KNV6LJvE7+w7h2Dy0yIzf7y86t0l4n8gETb
plvEUJ/lu9RYzTiZY/RxgBFYVTV59EqT45brSUtoe2Jcp8GSwiHslTHdfyFBwSo=
=gw4d
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
Active multiplexing is a nice feature as it allows several pointing devices
(such as touchpad and external mouse) use their native protocols at the
same time. Unfortunately many manufacturers do not implement the feature
properly even though they advertise it. The problematic implementations are
never fixed, since Windows by default does not use this mode, and move from
one BIOS/model of laptop to another. When active multiplexing is broken
turning it on usually results in touchpad, keyboard, or both unresponsive.
With PS/2 usage on decline (most of PS/2 devices in use nowadays are
internal laptop touchpads), I expect number of users who have laptops with
working MUX implementation, docking stations with external PS/2 ports, and
who are still using external PS/2 mice, to be rather small. Let's flip the
default to be OFF and allow activating it through i8042.nomux=0 kernel
option. We'll also keep DMI table where we can record known good models.
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately, ForcePad capability is not actually exported over PS/2, so
we have to resort to DMI checks.
Cc: stable@vger.kernel.org
Reported-by: Nicole Faerber <nicole.faerber@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUMZqoAAoJEHm+PkMAQRiGFC4H/i0b9vxCwe6VCXonpaDW03fI
JKE7v/zwDfhDngKSYfBWRSf3jXwfSHLvAvCgIvqTw5qBW3XSWF8xB7kJpWptQxIi
M6ePfaETt2mPYhEWWWxJK8boykiOXObDrFJVhfjHGsjbvmKiLPMaGYwXTSwZJ32V
fQDaA9Piugjc9wEY0d+6cjqUUEwlb4+GFz4Wv2oJgbpzxwgJS/XjQYk+3PrcdAXz
lmwPXQ+6ntJaducVu3JM2YYvaJLzTw+T+MPsWiTvaE4ILmuiw492VNY5XdyQQtb2
DSActOKCF2hIwnG+DMg63XV5FH81HqczwORDygBuxko0cURxupxMnaLPkVRpksk=
=+PRQ
-----END PGP SIGNATURE-----
Merge tag 'v3.17' into next
Synchronize with mainline to bring in changes to Synaptics and i8042
drivers.
This patch adds support for the ar1021 i2c based touchscreen.
The driver is quite simple and only supports the Touch
Reporting Protocol.
This is the final version for an RFC patch send a while ago.
http://www.spinics.net/lists/linux-input/msg29419.html
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To enable the cros_ec_keyb driver to be auto-loaded when build as
module add an of match table (and export it) to match the modalias
information passed on to userspace as the Cros EC MFD driver registers
the MFD subdevices with an of_compatibility string.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the format string for serio device name generation to avoid negative
device numbers when the id exceeds the maximum signed integer value.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the format string for input device name generation to avoid negative
device numbers when the id exceeds the maximum signed integer value.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
Let's automatically set EV_ABS bit in device's event type list when calling
input_set_abs_params() so that drivers do not have to do it explicitly.
These calls are never in a hot paths so we won't lose much time by setting
the same bit several times.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In case we start with the device not fully quiesced we should make sure we
cancel the workqueue after freeing interrupt.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change switch to managed resources to simplifies error handling
and module unloading and does away with platform_driver remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 'max' size passed into the function is measured in number of bits
(KEY_MAX, LED_MAX, etc) so we need to convert it accordingly before trying
to copy the data out, otherwise we will try copying too much and end up
with up with a page fault.
Reported-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of having users of the ChromeOS EC call the interface-specific
cmd_xfer() callback directly, introduce a central cros_ec_cmd_xfer()
to use instead. This will allow us to put all the locking and retry
logic in one place instead of duplicating it across the different
drivers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.
Replace the uses with standard structure definitions instead. This is
similar to pci and usb device registration.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Pull input fix from Dmitry Torokhov:
"A small fixup to i8042 adding Asus X450LCP to the nomux list"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - fix Asus X450LCP touchpad detection
ACPI device enumeration mechanism changed a lot since 3.16-rc1.
ACPI device objects with _HID will be enumerated to platform bus by default.
For the existing PNP drivers that probe the PNPACPI devices, the device ids
are listed explicitly in drivers/acpi/acpi_pnp.c.
But ACPI folks will continue their effort on shrinking this id list by
converting the PNP drivers to platform drivers, for the devices that don't
belong to PNP bus in nature.
Signed-off-by: Jin Yao <yao.jin@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to add this module to the nomux table to be able to detect the
touchpad.
Cc: stablevger.kernel.org
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull input updates from Dmitry Torokhov:
"A few quirks for i8042/AT keyboards and a small device tree doc fix
for Atmel Touchscreens"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - fix merge in DT documentation
Input: i8042 - also set the firmware id for MUXed ports
Input: i8042 - add nomux quirk for Avatar AVIU-145A6
Input: i8042 - add Fujitsu U574 to no_timeout dmi table
Input: atkbd - do not try 'deactivate' keyboard on any LG laptops
make C=2 CHECK="scripts/coccicheck" MODE=report COCCI=scripts/coccinelle/misc/irqf_oneshot.cocci ./drivers/input/misc/palmas-pwrbutton.o
Reports:
drivers/input/misc/palmas-pwrbutton.c:213:9-29: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT
Palmas power button just needs threaded IRQ handler since I2C operations
are involved and there is nothing in non-threaded primary handler we could
do.
So mark the request with ONESHOT as it should have been done in these
cases.
Fixes: adff5962fd ("Input: introduce palmas-pwrbutton")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Asus X450 and X550 laptops use a PS/2 touchpad from a new
manufacturer called FocalTech:
https://bugzilla.kernel.org/show_bug.cgi?id=77391https://bugzilla.redhat.com/show_bug.cgi?id=1110011
The protocol for these devices is not known at this time, but even
without knowing the protocol they need some special handling. They get
upset by some of our other PS/2 device probing, and once upset generate
random mouse events making things unusable even with an external mouse.
This patch adds detection of these devices based on their pnp ids, and
when they are detected, treats them as a bare ps/2 mouse. Doing things
this way they at least work in their ps/2 mouse emulation mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The matches_pnp_id function from the synaptics driver is useful for other
drivers too. Make it a generic psmouse helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current codes in gameport and analog joystick drivers for the time
accounting have a long-standing problem when the system is running
with CPU freq; since the timing is measured via TSC or sample counter,
the calculation isn't reliable.
In this patch, as a simple fix, use the standard ktime to measure the
timing. In case where no high resolution timer is available,
use_ktime bool option is provided to both modules. Setting
use_ktime=false switches to the old methods.
Tested-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver to supports the haptic controller on MAX77693 Multifunction
device with PMIC, CHARGER, LED, MUIC, HAPTIC.
This driver supports external pwm and LRA (Linear Resonant Actuator) motor.
User can control the haptic device via force feedback framework.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many palmas family of PMICs have support for interrupt based power button.
This allows the device to notify the processor of external push button
events over the shared palmas interrupt. However, this event is generated
only during a "press" operation. Software is supposed to poll(sigh!) for
detecting a release event.
The PMIC also supports ability to power off independent of the software
decisions when the button is pressed for a long duration if the PMIC is
appropriately configured on the platform.
Even though the function is similar to twl4030_pwrbutton, it is
substantially different in operation to belong to a new driver of it's own.
Based on original work done by Girish S Ghongdemath <girishsg@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
So that firmware-id matching can be used with multiplexed aux ports too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The sys_vendor / product_name are somewhat generic unfortunately, so this
may lead to some false positives. But nomux usually does no harm, where as
not having it clearly is causing problems on the Avatar AVIU-145A6.
https://bugzilla.kernel.org/show_bug.cgi?id=77391
Cc: stable@vger.kernel.org
Reported-by: Hugo P <saurosii@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are getting more and more reports about LG laptops not having
functioning keyboard if we try to deactivate keyboard during probe.
Given that having keyboard deactivated is merely "nice to have"
instead of a hard requirement for probing, let's disable it on all
LG boxes instead of trying to hunt down particular models.
This change is prompted by patches trying to add "LG Electronics"/"ROCKY"
and "LG Electronics"/"LW60-F27B" to the DMI list.
https://bugzilla.kernel.org/show_bug.cgi?id=77051
Cc: stable@vger.kernel.org
Reported-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Reported-by: Georgios Tsalikis <georgios@tsalikis.net>
Tested-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"An update to Synaptics PS/2 driver to handle "ForcePads" (currently
found in HP EliteBook 1040 laptops), a change for Elan PS/2 driver to
detect newer touchpads, bunch of devices get annotated as Trackpoint
and/or Pointer to help userspace classify and handle them, plus
assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: serport - add compat handling for SPIOCSTYPE ioctl
Input: atmel_mxt_ts - fix double free of input device
Input: synaptics - add support for ForcePads
Input: matrix_keypad - use request_any_context_irq()
Input: atmel_mxt_ts - downgrade warning about empty interrupts
Input: wm971x - fix typo in module parameter description
Input: cap1106 - fix register definition
Input: add missing POINTER / DIRECT properties to a bunch of drivers
Input: add INPUT_PROP_POINTING_STICK property
Input: elantech - fix detection of touchpad on ASUS s301l
When running a 32-bit inputattach utility in a 64-bit system, there will be
error code "inputattach: can't set device type". This is caused by the
serport device driver not supporting compat_ioctl, so that SPIOCSTYPE ioctl
fails.
Cc: stable@vger.kernel.org
Signed-off-by: John Sung <penmount.touch@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
[Nick Dyer: reworked to move free of input device into separate function
and only call in paths that require it.]
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
ForcePads are found on HP EliteBook 1040 laptops. They lack any kind of
physical buttons, instead they generate primary button click when user
presses somewhat hard on the surface of the touchpad. Unfortunately they
also report primary button click whenever there are 2 or more contacts
on the pad, messing up all multi-finger gestures (2-finger scrolling,
multi-finger tapping, etc). To cope with this behavior we introduce a
delay (currently 50 msecs) in reporting primary press in case more
contacts appear.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When trying to use the matrix-keypad driver with GPIO drivers that
require nested irq handlers (e.g. I2C GPIO adapters like PCA9554),
request_irq() fails because the GPIO driver requires a threaded
interrupt handler.
Use request_any_context_irq() to be able to use any GPIO driver as
keypad driver.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the case where the CHG/interrupt line mode is not configured correctly,
this warning is output to dmesg output for each interrupt. Downgrade the
message to debug.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adding support for the DRV2667 haptic driver. This device has the ability
to store vibration patterns in RAM and execute them once the GO bit is set.
The initial driver sets a basic waveform in the first waveform sequence and
will play the waveform when the GO bit is set and will continously play the
waveform until the GO bit is unset.
Data sheet is here: http://www.ti.com/product/drv2667
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the correct register address for Calibration Active and Interrupt
Enable.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
I've not done a full audit of all mouse drivers, I noticed these ones were
missing the POINTER property while working on the POINTING_STICK property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is useful for userspace to know that there not dealing with a regular
mouse but rather with a pointing stick (e.g. a trackpoint) so that
userspace can e.g. automatically enable middle button scrollwheel
emulation.
It is impossible to tell the difference from the evdev info without
resorting to putting a list of device / driver names in userspace, this is
undesirable.
Add a property which allows userspace to see if a device is a pointing
stick, and set it on all the pointing stick drivers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The userspace xboxdrv driver knows some more device ids than the kernel.
This patch adds the missing xbox gamepads from [1] to xpad.c
[1] https://github.com/Grumbel/xboxdrv/blob/master/src/xpad_device.cpp
Signed-off-by: Benjamin Valentin <benpicco@zedat.fu-berlin.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The xpad driver recognizes Razer Sabertooth controllers as generic xbox
controller, while it is really a 360 controller. This patch adds pid/vid
mappings for the controller so that it is correctly recognized.
Signed-off-by: Frank Razenberg <frank@zzattack.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"A fix for MT breakage, enhancement to Elantech PS/2 driver and a
couple of assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add support for trackpoint found on some v3 models
Input: elantech - reset the device when elantech probe fails
Input: ALPS - suppress message about 'Unknown touchpad'
Input: fix used slots detection breakage
Input: sparc - i8042-sparcio.h: fix unused kbd_res warning
Input: atmel_mxt_ts - improve description of gpio-keymap property
Previous algorithm was a bit conservative and complicating with respect to
identifying key ghosting. This CL uses the bitops hamming weight function
(hweight8) to count the number of matching rows for colM & colN. If that
number is > 1 ghosting is present.
Additionally it removes NULL keys and our one virtual keypress KEY_BATTERY
from consideration as these inputs are never physical keypresses.
Signed-off-by: Todd Broch <tbroch@chromium.org>
Reviewed-by: Vincent Palatin <vpalatin@chromium.org>
Reviewed-by: Luigi Semenzato <semenzato@chromium.org>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUA8qAAAoJEHm+PkMAQRiGRNwH/194A8PirGSXmM83dMoW2RHU
j597TT0frxfHiDDcHpIYZBg5Z0qV6ZvY2982HzYJr3eEDzXYzz0nI5TlNBeNPy1i
yRb2c74/BKvIvSSj9s4MZ9918HbYWE7L1bJAoVs7uc50iANgVSuesOrWVzTylSor
/cNwFV1GMjIVEGwP1/lZy40NQD92ZG1kkttzMnrrH9E5TQ7UK+DIAfJViFIYv8Cp
fw2U5VKrZ7qZm0XlOq5keN/mD6lKicSBTlPdvSICHkzOBbUlS35tTnW3co9jmpba
XUKNqM4YvXJWzbgrAGT8CHBaQTOMylRO/a2AOIwqOciODJJB0CqfJ0CtHUffOnE=
=yN6O
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc3' into next
Sync with mainline to bring in Chrome EC changes.
Add a check to ensure that LRA libraries are not mixed with the ERM mode.
If ERM mode and the Library is empty "OR" the LRA library then exit, as the
LRA and empty libraries are not applicable for the ERM actuator.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Removing some #defines that are not and should never be used pertaining to
I2C.
Removing:
define DRV260X_ALLOWED_R_BYTES 25
define DRV260X_ALLOWED_W_BYTES 2
define DRV260X_MAX_RW_RETRIES 5
define DRV260X_I2C_RETRY_DELAY 10
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some elantech v3 touchpad equipped laptops also have a trackpoint, before
this commit, these give sync errors. With this patch, the trackpoint is
provided as another input device: 'Elantech PS/2 TrackPoint'
The patch will also output messages that do not follow the expected pattern.
In the mean time I've seen 2 unknown packets occasionally:
0x04 , 0x00 , 0x00 , 0x00 , 0x00 , 0x00
0x00 , 0x00 , 0x00 , 0x02 , 0x00 , 0x00
I don't know what those are for, but they can be safely ignored.
Currently all packets that are not known to v3 touchpad and where
packet[3] (the fourth byte) lowest nibble is 6 are now recognized as
PACKET_TRACKPOINT and processed by the new elantech_report_trackpoint.
This has been verified to work on a laptop Lenovo L530 where the
touchpad/trackpoint combined identify themselves as:
psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x350f02)
psmouse serio1: elantech: Synaptics capabilities query result 0xb9, 0x15, 0x0c.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
elantech_init() calls elantech_set_absolute_mode which sets the driver in
an absolute mode. When after this the elantech_init fails, it is best to
turn the ps/2 mouse emulation mode back on by calling psmouse_reset() so
that it can work as a regular mouse.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When we fail to match data returned by E7 and EC reports we state that we
found "Unknown ALPS touchpad" whereas it is most likely it is not ALPS
touchpad at all. Change wording a bit and reduce the message to debug so
that it does not litter users logs and confuse them.
Reported-by: Paul Menzel <paulepanter@users.sourceforge.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit f8ec894945 allowed external callers
use slot dropping logic, unfortunately it also broke external users of
input_mt_is_used() as we stopped incrementing frame count unless input
device was set up to automatically drop unused slots.
Fixes: f8ec894945 ("Input: MT - make slot cleanup callable outside
mt_sync_frame()")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=83081
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the TI drv260x haptics/vibrator driver. This device uses the input
force feedback to produce a wave form to driver an ERM or LRA actuator
device.
The initial driver supports the devices real time playback mode. But the
device has additional wave patterns in ROM. This functionality will be
added in future patchsets.
Product data sheet is located here: http://www.ti.com/product/drv2605
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
kbd_res is used only when CONFIG_PCI is defined; condition its declaration as
well. This fixes the following compilation warning:
drivers/input/serio/i8042-sparcio.h:20:25: warning: ‘kbd_res’ defined but not used [-Wunused-variable]
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fixes from Dmitry Torokhov:
"Second round of updates for the input subsystem. Mostly small fixups
to the code merged in the first round (atmel_mxt_ts, wacom) but also a
smallish patch to xbox driver to support Xbox One controllers and a
patch to better handle Synaptics profile sensors found in Cr-48
Chromebooks that should not affect any other devices"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: edt-ft5x06 - remove superfluous assignment
Input: xpad - add support for Xbox One controllers
Input: atmel_mxt_ts - fix a few issues reported by Coverity
Input: atmel_mxt_ts - split config update a bit
Input: atmel_mxt_ts - simplify mxt_initialize a bit
Input: joystick - use get_cycles on ARMv8
Input: wacom - fix compiler warning if !CONFIG_PM
Input: cap1106 - allow changing key mapping from userspace
Input: synaptics - use firmware data for Cr-48
Input: synaptics - properly initialize slots for semi-MT
Input: MT - make slot cleanup callable outside mt_sync_frame()
Input: atmel_mxt_ts - mXT224 DMA quirk was fixed in firmware v2.0.AA
Somehow we ended up with a duplicate line in edt_ft5x06_register_write()
Signed-off-by: Maks Naumov <maksqwe1@ukr.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Xbox One controllers require an initialization message to start sending
data, so xpad_init_output becomes a required function. The Xbox One
controller does not have LEDs like the Xbox 360 controller, so that
functionality is not implemented. The format of messages controlling rumble
is currently undocumented, so rumble support is not yet implemented.
Note that Xbox One controller advertises three interfaces with the same
interface class, subclass and protocol, so we have to also match against
interface number.
Signed-off-by: Ted Mielczarek <ted@mielczarek.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This should fix the following issues reported by Coverity:
*** CID 1230625: Logically dead code (DEADCODE)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1692 in mxt_initialize()
*** CID 1230627: Missing break in switch (MISSING_BREAK)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1436 in mxt_get_object_table()
*** CID 1230629: Out-of-bounds write (OVERRUN)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1267 in mxt_update_cfg()
*** CID 1230632: Unused pointer value (UNUSED_VALUE)
/drivers/input/touchscreen/atmel_mxt_ts.c: 1211 in mxt_update_cfg()
Acked-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's split config update code a bit so it is hopefully a bit easier to
read. Also, the firmware update callback should be the entity releasing
firmware blob, not lower layers.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
I think having control flow with 2 goto/labels/flags is quite hard to read,
this version is a bit more readable IMO.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
As with ARM the ARMv8 architecture provides a cycle counter which can be
used to provide a high resolution time for the joystick driver and
silence the build warning that results from not having a precise timer
on ARMv8, making allmodconfig and allyesconfig quieter.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- big update to Wacom driver by Benjamin Tissoires, converting it to
HID infrastructure and unifying USB and Bluetooth models
- large update to ALPS driver by Hans de Goede, which adds support for
newer touchpad models as well as cleans up and restructures the code
- more changes to Atmel MXT driver, including device tree support
- new driver for iPaq x3xxx touchscreen
- driver for serial Wacom tablets
- driver for Microchip's CAP1106
- assorted cleanups and improvements to existing drover and input core
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (93 commits)
Input: wacom - update the ABI doc according to latest changes
Input: wacom - only register once the MODULE_* macros
Input: HID - remove hid-wacom Bluetooth driver
Input: wacom - add copyright note and bump version to 2.0
Input: wacom - remove passing id for wacom_set_report
Input: wacom - check for bluetooth protocol while setting OLEDs
Input: wacom - handle Intuos 4 BT in wacom.ko
Input: wacom - handle Graphire BT tablets in wacom.ko
Input: wacom - prepare the driver to include BT devices
Input: hyperv-keyboard - register as a wakeup source
Input: imx_keypad - remove ifdef round PM methods
Input: jornada720_ts - get rid of space indentation and use tab
Input: jornada720_ts - switch to using managed resources
Input: alps - Rushmore and v7 resolution support
Input: mcs5000_ts - remove ifdef around power management methods
Input: mcs5000_ts - protect PM functions with CONFIG_PM_SLEEP
Input: ads7846 - release resources on failure for clean exit
Input: wacom - add support for 0x12C ISDv4 sensor
Input: atmel_mxt_ts - use deep sleep mode when stopped
ARM: dts: am437x-gp-evm: Update binding for touchscreen size
...
Wire up support for EVIOC{G|S}KEYCODE to allow users change key mappings
from userspace.
Reviewed-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The profile sensor clickpad in a Cr-48 Chromebook does a reasonable job
of tracking individual fingers. This tracking isn't perfect, but,
experiments show that it works better than just passing "semi-mt" data
to userspace, and making userspace try to deduce where the fingers are
given a bounding box.
This patch tries to report correct two-finger positions instead of the
{(min_x, min_y), (max_x, max_y)} for profile sensor clickpads on Cr-48
chromebooks. Note that this device's firmware always reports the higher
(smaller y) finger in the "sgm" packet, and the lower (larger y) finger
in the "agm" packet. Thus, when a new finger arrives on the pad, the
kernel driver uses input core's contact tracking facilities to match
contacts with slots.
Inspired by patch by Daniel Kurtz <djkurtz@chromium.org> and Chung-yih
Wang <cywang@chromium.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Semi-MT devices are pointers too, so let's tell that to
input_mt_init_slots(), as well as let it set up the devices as semi-MT,
instead of us doing it manually.
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some semi-mt drivers use the slots in a manual way, but may still
want to call parts of the frame synchronization logic. This patch
makes input_mt_drop_unused callable from those drivers.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
With this patch, we can press a key to wake up the VM after the VM executes
"echo freeze > /sys/power/state".
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull sparc updates from David Miller:
1) Add sparc RAM output to /proc/iomem, from Bob Picco.
2) Allow seeks on /dev/mdesc, from Khalid Aziz.
3) Cleanup sparc64 I/O accessors, from Sam Ravnborg.
4) If update_mmu_cache{,_pmd}() is called with an not-valid mapping, do
not insert it into the TLB miss hash tables otherwise we'll
livelock. Based upon work by Christopher Alexander Tobias Schulze.
5) Fix BREAK detection in sunsab driver when no actual characters are
pending, from Christopher Alexander Tobias Schulze.
6) Because we have modules --> openfirmware --> vmalloc ordering of
virtual memory, the lazy VMAP TLB flusher can cons up an invocation
of flush_tlb_kernel_range() that covers the openfirmware address
range. Unfortunately this will flush out the firmware's locked TLB
mapping which causes all kinds of trouble. Just split up the flush
request if this happens, but in the long term the lazy VMAP flusher
should probably be made a little bit smarter.
Based upon work by Christopher Alexander Tobias Schulze.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next:
sparc64: Fix up merge thinko.
sparc: Add "install" target
arch/sparc/math-emu/math_32.c: drop stray break operator
sparc64: ldc_connect() should not return EINVAL when handshake is in progress.
sparc64: Guard against flushing openfirmware mappings.
sunsab: Fix detection of BREAK on sunsab serial console
bbc-i2c: Fix BBC I2C envctrl on SunBlade 2000
sparc64: Do not insert non-valid PTEs into the TSB hash table.
sparc64: avoid code duplication in io_64.h
sparc64: reorder functions in io_64.h
sparc64: drop unused SLOW_DOWN_IO definitions
sparc64: remove macro indirection in io_64.h
sparc64: update IO access functions in PeeCeeI
sparcspkr: use sbus_*() primitives for IO
sparc: Add support for seek and shorter read to /dev/mdesc
sparc: use %s for unaligned panic
drivers/sbus/char: Micro-optimization in display7seg.c
display7seg: Introduce the use of the managed version of kzalloc
sparc64 - add mem to iomem resource
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
We can annotate the suspend/resume functions with '__maybe_unused' and get
rid of the ifdef, which makes the code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This switches the driver to using managed resources to simplify error
handling and to do away with remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for querying the physical size from the touchpad for Rushmore
and v7 touchpads, and use that to tell userspace the device resolution.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We can annonate the suspend/resume functions with '__maybe_unused' and get
rid of the ifdef, which makes the code smaller and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When a kernel has CONFIG_PM=y and CONFIG_PM_SLEEP=n the following warnings are
seen:
drivers/input/touchscreen/mcs5000_ts.c:252:12: warning: 'mcs5000_ts_suspend' defined but not used [-Wunused-function]
static int mcs5000_ts_suspend(struct device *dev)
^
drivers/input/touchscreen/mcs5000_ts.c:262:12: warning: 'mcs5000_ts_resume' defined but not used [-Wunused-function]
static int mcs5000_ts_resume(struct device *dev)
Protect the suspend/resume functions with CONFIG_PM_SLEEP in order to fix these
build warnings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Input device must be released(input_free_device) when ads7846_probe_dt
fails. This fixes the same by releasing resources on failure.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By writing zero to both the active and idle cycle times the maXTouch device
is put into a deep sleep mode when it consumes minimal power. It is
unnecessary to change the configuration of any other objects (for example
to disable T9 touchscreen).
It is counterproductive to reset the chip on resume, it will result in a
long delay. However it is necessary to issue a calibrate command after the
chip has spent any time in deep sleep.
This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide device tree support and binding information. Also provide support
for a new chip "pixcir_tangoc".
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some variants of the Pixcir touch controller support up to 5 simultaneous
fingers and hardware tracking IDs. Prepare the driver for that.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch to using the Type-B Multi-Touch protocol.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Such as found on the new Toshiba Portégé Z30-A and Z40-A.
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
[hdegoede@redhat.com: Remove softbutton handling, this is done in userspace]
[hdegoede@redhat.com: Report INPUT_PROP_BUTTONPAD]
[hdegoede@redhat.com: Do not report fake PRESSURE, reporting BTN_TOUCH is
enough]
[hdegoede@redhat.com: Various cleanups / refactoring]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
So that decode functions can return a failure when appropriate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If we detect more then 2 fingers report 2 touches, rather then only
reporting the upper left corner of the bounding box.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move all the semi-mt specific handling shared between the v3 and v4
handling code to a common helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For v3 protocol devices, use the more accurate single touch data when the
mt data contains only one finger. Note the mt data reporting a finger count
of 1 should never happen, but better safe then sorry.
This brings the v3 bitmap handling in line with what the v4 code does,
allowing to factor out the common bits into a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When there are 2 fingers on the pad we don't know which one is which, so
use input_mt_assign_slots to make sure the right set of coordinates ends
up in the right slot.
Besides ensuring things end up in the right slot, this also results in a
nice cleanup, since sync_frame also handles non mt position and btn_touch
reporting.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a preparation patch for switching the DIY mt handling to using
input_mt_assign_slots && input_mt_sync_frame.
struct alps_fields is quite large, so while making changes to almost all uses
of it lets put it in our priv data instead of on the stack.
Having it in our priv data also allows using it directly for storing values
which need to be cached, rather then having separate x, y, z, fingers, etc.
copies in our priv data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes 2 fingers at the same height or width on the touchpad getting
reported at different y / x coordinates.
Note num_bits is always at least 1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
alps_process_bitmap was resetting the point bit-count as soon as it saw
2 0 bits in a row. This means that unless the high point actually is at
the end of the bitmap, it would always get its num_bits set to 0.
Instead reset num_bits to 0 on a 0->1 transition, so that with > 2 fingers
we only count the number of bits occupied by the highest finger.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out the identical code for getting the bitmap points for x and y into
a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rushmore models don't have the Y-axis data in the bitmap inverted. Since
we now have 2 different Y orientations, make the Y bitmap data processing
use a forward loop like the X bitmap data processing, unifying the 2,
and invert the data later, except on Rushmore.
So far no-one has noticed this because the synaptics driver only uses the
non mt coordinates (except on clickpads, and there are no alps clickpads
using process_bitmap).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
V3 models only report mt bitmap data when there are 2 or more fingers on
the touchpad. So always generate 2 positions in alps_process_bitmap, and
for v3 models only fall back to st data when there was no mt data in a
mt packet (which should never happen).
This fixes 2 finger scrolling not working when using 2 fingers close to
each other.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wacom.ko is now a full HID driver, we have to move it into the proper
subdirectory: drivers/hid.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
No Functional changes, just some reordering.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
pktlen is now overwritten by the driver directly by reading the hid
report descriptor. There is no need to declare it statically.
We also move down the position of the field in the struct so that
we can keep the current declaration of Wacom devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This may infer a small difference with the previous implementation
due to the DIV_ROUND_CLOSEST() in the hid implementation.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
HID already parses the report descriptor, so use it instead of implementing
our own. The special case for Bamboo PT 3rd gen is also removed and
handled in the same way Intuos 5 is treated, by hardcoding it in the
driver. Last, the unit_exponent stored into the hid field already is
signed, so there is no need to handle a two's complement anymore.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Removes one more need of usb and intf.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the HID device as the parent for the power device when dealing with
a wireless receiver.
Removes one more usb dependency and does not break user space.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wacom tablets can share different physical sensors on one physical device.
These are called siblings in the code. The current way of implementation
relies on the USB topology to be able to share data amongs those sensors.
We can replace the code to match a HID subsystem, without involving the USB
topology:
- the first probed sensor does not find any siblings in the list
wacom_udev_list, so it creates its own wacom_hdev_data with its own
struct hid_device
- the other sensor checks the current list of siblings in wacom_hdev_data,
and if there is a match, it associates itself to the matched device.
To be sure that we are not associating different sensors from different
physical devices, we also check for the phys path of the hid device which
contains the USB topology.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Matches the current behavior of the HID subsystem and removes one more
dependency over USB.
The current user space clients which relies on this to fetch the
LEDs path need an update. However, we already break them in the
kernel v3.11 for the Bluetooth Wacom devices. They are going to be fixed
soon.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Removes one more dependency over USB, but requires some changes in
the user space to find the sysfs files correctly.
This patch breaks the user space. However, the number of program
accessing the LEDs is quite limited and we can easily patch them
to handle the new HID behavior.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This removes an USB dependency and is more accurate: the computed pktlen
is the actual maximum size of the reports forwarded by the device.
Given that the pktlen is correctly computed/validated, we can store it now
in the features struct instead of having a special handling in the rest of
the code.
Likewise, this information is not mandatory anymore in the description
of devices in wacom_wac.c. They will be removed in a separate patch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
HID core already retrieves the report descritor. There is no need
to ask ourself for one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wacom.ko was a plain USB driver for a HID device. The communications
from/to the devices can actually be replaced with the HID API.
At the USB level, the reports are exactly the same.
This will allow to use uhid virtual devices instead of true USB devices.
This step is necessary to implement regression tests.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All USB Wacom tablets are actually HID devices.
For historical reasons, they are handled as plain USB devices.
The current code makes more and more reference to the HID subsystem
like implementing its own HID report descriptor parser to handle new
devices.
From the user point of view, we can transparently switch from this state
to a driver handled in the HID subsystem and clean up a lot of USB specific
code in the wacom.ko driver.
The other benefit once the USB dependecies have been removed is that we can
use a tool like uhid to make regression tests and allow further cleanup or
new implementations without risking breaking current behaviors.
To match the current handling of devices in wacom_wac.c, we rely on the
hid_type set by usbhid. usbhid sets the hid_type to HID_TYPE_USBMOUSE when
it sees a USB boot mouse protocol declared and HID_TYPE_USBNONE when the
device is plain HID. There is thus a one to one matching between the list
of supported devices before and after the switch from USB to HID.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current wacom code redefines constants that are already in linux/hid.h
This patch includes the official implementation and use it accross the code.
There is a conflict with HID_USAGE and others at the same level:
- in the wacom.ko implementation, those are the #define regarding the
value of the field in the report descriptor
- in the hid.h, those are bitmask
So add HDESC_ in their current definition.
Also, the struct hid_descriptor slightly differs from the linux/hid.h
point of view, so mark it as custom for this driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Wireless Receiver should also behave in the same way than regular
USB devices.
To simplify the unregistering of the different devices,
wacom_unregister_inputs() is introduced.
For consistency, the function wacom_register_input() is renamed into
wacom_register_inputs().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely removed from pad devices. If it is not
here, xf86-input-wacom correctly generates ones for its internal
use.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely removed from the pad device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We rely on the return code of wacom_bpt*() to do the input_sync().
wacom_wac_irq() then properly sync the input devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely dropped for pad input devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, the pad events are sent through the stylus input device
for the Intuos/Cintiqs, and through the touch input device for the
Bamboos.
To differentiate the buttons pressed on the pad from the ones pressed
on the stylus, the Intuos/Cintiq uses MISC_SERIAL and ABS_MISC. This
lead to a multiplexing of the events into one device, which are then
splitted out in xf86-input-wacom. Bamboos are not using MISC events
because the pad is attached to the touch interface, and only BTN_TOUCH
is used for the finger (and DOUBLE_TAP, etc...). However, the user space
driver still splits out the pad from the touch interface in the same
way it does for the pro line devices.
The other problem we can see with this fact is that some of the Intuos
and Cintiq have a wheel, and the effective range of the reported values
is [0..71]. Unfortunately, the airbrush stylus also sends wheel events
(there is a small wheel on it), but in the range [0..1023]. From the user
space point of view it is kind of difficult to understand that because
the wheel on the pad are quite common, while the airbrush tool is not.
A solution to fix all of these problems is to split out the pad device
from the stylus/touch. This decision makes more sense because the pad is
not linked to the absolute position of the finger or pen, and usually, the
events from the pad are filtered out by the compositor, which then convert
them into actions or keyboard shortcuts.
For backward compatibility with current xf86-input-wacom, the pad devices
still present the ABS_X, ABS_Y and ABS_MISC events, but they can be
completely ignored in the new implementation.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This field was not used for 9 years, it is time to assign it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 1b2faaf7e2.
The Intuos4 series presents a bug in which it hangs if it receives
a set feature command while switching to the enhanced mode.
This bug is triggered when plugging an Intuos 4 while having
a gnome user session up and running.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wacom_wac.h will be moving to drivers/hid. Since we only need 3 definitions
from it let's simply copy them over.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wire up open/close so we do not try to send events until someone uses them;
this also allows us to remove micro_ts_remove() and rely fully on managed
resources.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a driver for the touchscreen connected to the Atmel
microcontroller on the iPAQ h3xxx series.
Based on a driver from handhelds.org 2.6.21 kernel, written by Alessandro
GARDICH, with the bulk of the code for the new input architecture rewritten
by Dmitry Atamonow, and the final polish by Linus Walleij.
Signed-off-by: Alessandro GARDICH <gremlin@gremlin.it>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTzJFGAAoJEHm+PkMAQRiGNzQH/087gQch5K+A2HKvPzjUXq57
G82DJHLONMMq8+NY3Vqhp8g2V8zRbXGJEvMJMsyuscO37Vo7ADcrYo8lqY9w5bIl
h+Zarhkqz0rqRs2SfMMIVzdd2W7MzL+lqj3GplGPxHztw0+qk7PRKILx6eRppGaH
JaD4NfkD5+1vfve/2d1ze9D5pCiw6PFNzjesKZxScQhNhIyLdRamfSTY4r9XeURo
CxpwjphEYfvAcgc39mwzEHPHyKSqULu0By6R8FXQpJ9QjVtzcGEiF+cPqGncpZOR
5ZSyU5e1CpBl9w8o6Lm9ewXmaCSnBU/VFrOwWvZrXfokZedXBOz7KdShU93XFjU=
=0VJM
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc6' into next
Merge with mainline to bring in changes to MFD to allow merging
ipaq-micro-ts driver.
maXTouch chips allow the reading of multiple messages in a single I2C
transaction, which reduces bus overhead and improves performance/latency. The
number of messages available to be read is given by the value in the T44
object which is located directly before the T5 object.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is in preparation for support of the T44 message count object.
Also, cache T5 address to avoid lookup on every interrupt cycle.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By storing the previous T6 status byte multiple debug output of the same
status can be suppressed (for example CFGERR).
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The T5 object may have various sizes depending on the objects used on the
particular maXTouch chip and firmware version, therefore it can't be
hardcoded in the driver. Allocate a buffer on probe instead.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MXT device may be in bootloader mode on probe, due to:
1) APP CRC failure, either:
a) flash corruption
b) bad power or other intermittent problem while checking CRC
2) If the device has been reset 10 or more times without accessing comms
3) Warm probe, device was in bootloader mode already
This code attempts to recover from 1(b) and 3.
There is an additional complexity: we have to try two possible bootloader
addresses because the mapping is not one-to-one and we don't know the exact
model yet.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Later chips (for example mXT1664S) different mappings for bootloader
addresses. This means that we must look at the family ID to determine
which address to use.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On a warm probe, the device might be in a state where an flash operation was
not completed.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the bootloader on the touchscreen controller fails to initialise the
firmware image, it stays in bootloader mode and reports a failure. It is
possible to reflash a working firmware image from this state.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By validating the checksum, we can identify if the configuration is
corrupt. In addition, this patch writes the configuration in a short
series of block writes rather than as many individual values.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The existing implementation which encodes the configuration as a binary
blob in platform data is unsatisfactory since it requires a kernel
recompile for the configuration to be changed, and it doesn't deal well
with firmware changes that move values around on the chip.
Atmel define an ASCII format for the configuration which can be exported
from their tools. This patch implements a parser for that format which
loads the configuration via the firmware loader and sends it to the MXT
chip.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Touchpads are pointers, so make sure to pass the correct values to
input_mt_report_pointer_emulation(). Without this, tap-to-click doesn't
work.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is useful to initialise the input device later:
- Screen parameters may not be not known yet, for instance if waiting for
firmware loader to return.
- Device may be in bootloader mode on probe (but could still be recovered by
firmware download).
In addition, later devices have a different touchscreen object (T100) which
requires handling differently.
This also reduces the complexity of the probe function.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The maXTouch chips use the CHG line to generate status events in bootloader
mode, and during configuration download, before there is enough information
to configure the input device. Therefore set up the interrupt handler
earlier.
However, this introduces states where parts of the interrupt processing
must not run. Use data->object_table as a way to tell whether the chip
information is valid, and data->input_dev as a way to tell whether it is
valid to generate input report.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the monotonic timestamp with ktime_mono_to_real() in
evdev_events().
In evdev_queue_syn_dropped() we can call either ktime_get() or
ktime_get_real() depending on the clkid. No point in having two calls
for CLOCK_REALTIME.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The memory are mapped using of_ioremap() which is
an indication this is sbus memory.
Shift all uses of inb/outb to the sbus variants.
The inb/outb methods uses ASI_PHYS_BYPASS_EC_E_L,
whereas sbus_ variants uses ASI_PHYS_BYPASS_EC_E.
The difference is if the reads/writes are done in
native or little endian.
But for byte reads/writes there is no difference
so this does not matter for inb/outb - and this
driver only uses the byte variants.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ioctl is the counterpart to EVIOCGVERSION and returns the
uinput-version the kernel was compiled with.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This moves basic checks and setup from uinput_setup_device() into
uinput_validate_absbits() to make it easier to use. This way, we can call
it from other places without copying the boilerplate code.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
