commit df73de9b0d ("mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON
is not enabled") introduced fallbacks for APIs, but missed out on adding
the header file. This would work only if linux/err.h is also included
in the source code from where this file is included. It would be better
to include linux/err.h in file to remove possible build errors.
Without this patch, we get following and similar build errors if this
header file is included in some source file and CONFIG_MFD_SYSCON is
not enabled.
include/linux/mfd/syscon.h: In function ‘syscon_node_to_regmap’:
include/linux/mfd/syscon.h:30:2: error: implicit declaration of function ‘ERR_PTR’ [-Werror=implicit-function-declaration]
return ERR_PTR(-ENOSYS);
^
include/linux/mfd/syscon.h:30:18: error: ‘ENOSYS’ undeclared (first use in this function)
return ERR_PTR(-ENOSYS);
^
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch introduces the preliminary support for PMICs X-Powers AXP202
and AXP209. The AXP209 and AXP202 are the PMUs (Power Management Unit)
used by A10, A13 and A20 SoCs and developed by X-Powers, a sister company
of Allwinner.
The core enables support for two subsystems:
- PEK (Power Enable Key)
- Regulators
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The pm8xxx read/write wrappers are no longer necessary now that
all the sub-device drivers are using the regmap API. Remove it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The device type was stored in sec_pmic_dev state container twice:
- unsigned long type (initialized from of_device_id or i2c_device_id)
- int device_type (initialized as above or from board files when there
is no DTS)
The 'type' field was never used outside of probe so it can be safely
removed.
Change also the device_type in sec_pmic_dev and sec_platform_data to
unsigned long to avoid any casts.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In certain boards the source for the clk32k clock can be gated. In these
boards the clk32k clock can be provided to the driver and it is going to be
enabled/disabled when it is needed.
If the clk32k clock is not provided the driver will assume that it is always
running.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All boards using twl6040 configures the i2c bus to 400KHz. While twl6040's
defaults to normal mode (100KHz). So far twl6040 has no problem with i2c
communication in this configuration it is safer to select fast i2c mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The valid gpio is GPIO0 ~ GPIO58, so ngpio should be 59.
This patch also renames RDC321X_MAX_GPIO to RDC321X_NUM_GPIO because it
actually means the number of available GPIOs.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Update the documentation for sec_pmic state container structure to
reflect current code.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The rtc-s5m driver does not support all of S2M and S5M chipsets
supported by main MFD sec-core driver. For such chipsets unsupported by
rtc-s5m, the MFD sec-core driver initialized regmap with default config.
This config in such cases wouldn't work at all.
The main MFD sec-core driver shouldn't initialize regmap for child
drivers which is not used by them and even not valid.
Move the allocation of RTC I2C dummy device and initialization of RTC
regmap from main MFD sec-core driver to the rtc-s5m driver. The rtc-s5m
driver will use proper regmap config for supported devices.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The *rdev[] is not used since commit 413be59e2f
"regulator: tps65218: Remove unnecessary regulator_unregister call".
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On systems with CONFIG_FRAME_WARN=1024, compiler warns the allocation of
an object of struct device on stack. Make the allocation dynamically to
fix the warning. Also change the caller's return type to int so as to
account for error handling.
drivers/mfd/abx500-core.c: In function ‘abx500_dump_all_banks’:
drivers/mfd/abx500-core.c:167:1: warning: the frame size of 1032 bytes
is larger than 1024 bytes [-Wframe-larger-than=]
Signed-off-by: Aurabindo J <mail@aurabindo.in>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds attributes to the Kontron PLD driver to allow
applications to retrieve firmware information.
Additionally the format has been changed to conform with the
representation in other Kontron software.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are two different variants of the tps658640 with slightly
different feature sets.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KGD4
-----END PGP SIGNATURE-----
Merge tag 'regulator-tps658640' into ib-from-regulator-3.16
regulator: Support newer revisions of tps658640
There are two different variants of the tps658640 with slightly
different feature sets.
The TPS658640 has a different set of output voltage for most LDO and
the RTC LDO isn't settable. This chip also report 2 different version
ID, as the datasheet doesn't list the possible values the second ID
has simply been named TPS658640v2.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The only platform using the STMPE expander now boots from
device tree using all-dynamic GPIO and IRQ number assignments, so
remove the mechanism to pass this from the device tree entirely.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The STMPE has VCC and VIO supply lines, and sometimes (as on
Ux500) this comes from a software-controlled regulator. Make
it possible to supply the STMPE with power from these
regulators.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit c42deffd5b.
commit <mmc: rtsx: add support for pre_req and post_req> did use
mutex_unlock() in tasklet, but mutex_unlock() can't be used in
tasklet(atomic context). The driver needs to use mutex to avoid
concurrency, so we can't use tasklet here, the patch need to be
removed.
The spinlock host->lock and pcr->lock may deadlock, one way to solve
the deadlock is remove host->lock in sd_isr_done_transfer(), but if
using workqueue the we can avoid using the spinlock and also avoid
the problem.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 chipset and its additional two LDO regulators.
These LDO regulators are controlled by the PMIC block with additional
regmap (different I2C slave address).
The MAX77836 charger and safeout regulators are almost identical to
MAX14577. The registers layout is the same, except values for charger's
current. The patch adds simple mapping between device type and supported
current by the charger regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for MAX77836 chipset to the max14577 extcon driver. The
MAX77836 MUIC has additional interrupts (VIDRM, ADC1K) so IRQ handling
is split up into two functions: max14577_parse_irq() and
max77836_parse_irq().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add Maxim 77836 support to max14577 driver. The chipsets have same MUIC
component so the extcon, charger and regulators are almost the same. The
MAX77836 however has also PMIC and Fuel Gauge.
The MAX77836 uses three I2C slave addresses and has additional interrupts
(related to PMIC and Fuel Gauge). It has also Interrupt Source register,
just like MAX77686 and MAX77693.
The MAX77836 PMIC's TOPSYS and INTSRC interrupts are reported in the
PMIC block. The PMIC block has different I2C slave address and uses own
regmap so another regmap_irq_chip is needed.
Since we have two regmap_irq_chip, use shared interrupts on MAX77836.
This patch adds additional defines and functions to the max14577 MFD core
driver so the driver will handle both chipsets. Also this patch replaces
"0x1 << N" with BIT(N) in defines for register masks.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch prepares for adding support for MAX77836 device to existing
max14577 driver by adding MAX14577 prefix to defines of interrupts.
This is only a rename-like patch, new code is not added.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch continues the preparation for adding support for MAX77836
device to existing max14577 driver.
Add enum for types of devices supported by this driver. The device type
will be detected by matching of_device_id, or i2c_device_id as a
fallback.
The patch also moves to separate function the code related to displaying
DeviceID register values.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add muic prefix to regmap config to differentiate between another regmap
config for MAX77836 PMIC node. Additionally remove unused
symbols: MAX14577_REG_INVALID and max14577_irq_source.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Nearly all of the registers in tps65090 combine control bits and
status bits. Turn off caching of all registers except the select few
that can be cached.
In order to avoid adding more duplicate #defines, we also move some
register offset definitions to the mfd driver (and resolve
inconsistent names).
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch factors out the reading of GPIOs for the Arizona devices
into a helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull LED updates from Bryan Wu:
"This cycle we got:
- new driver for leds-mc13783
- bug fixes
- code cleanup"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: make sure we unregister a trigger only once
leds: leds-pwm: properly clean up after probe failure
leds: clevo-mail: Make probe function __init
leds-ot200: Fix dependencies
leds-gpio: of: introduce MODULE_DEVICE_TABLE for module autoloading
leds: clevo-mail: remove __initdata marker
leds: leds-ss4200: remove __initdata marker
leds: blinkm: remove unnecessary spaces
leds: lp5562: remove unnecessary parentheses
leds: leds-ss4200: remove DEFINE_PCI_DEVICE_TABLE macro
leds: leds-s3c24xx: Trivial cleanup in header file
drivers/leds: delete non-required instances of include <linux/init.h>
leds: leds-gpio: add retain-state-suspended property
leds: leds-mc13783: Add devicetree support
leds: leds-mc13783: Remove unnecessary cleaning of registers on exit
leds: leds-mc13783: Use proper "max_brightness" value fo LEDs
leds: leds-mc13783: Use LED core PM functions
leds: leds-mc13783: Add MC34708 LED support
leds: Turn off led if blinking is disabled
ledtrig-cpu: Handle CPU hot(un)plugging
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
Lots of changes specific to one of the SoC families. Some that
stick out are:
* mach-qcom gains new features, most importantly SMP support for
the newer chips (Stephen Boyd, Rohit Vaswani)
* mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
* SMP support for Rockchips (Heiko Stübner)
* Lots of i.MX changes (Shawn Guo)
* Added support for BCM5301x SoC (Hauke Mehrtens)
* Multiplatform support for Marvell Kirkwood and Dove
(Andrew Lunn and Sebastian Hesselbarth doing the final part
of a long journey)
* Unify davinci platforms and remove obsolete ones (Sekhar Nori,
Arnd Bergmann)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=AGpV
-----END PGP SIGNATURE-----
Merge tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"Lots of changes specific to one of the SoC families. Some that stick
out are:
- mach-qcom gains new features, most importantly SMP support for the
newer chips (Stephen Boyd, Rohit Vaswani)
- mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
- SMP support for Rockchips (Heiko Stübner)
- Lots of i.MX changes (Shawn Guo)
- Added support for BCM5301x SoC (Hauke Mehrtens)
- Multiplatform support for Marvell Kirkwood and Dove (Andrew Lunn
and Sebastian Hesselbarth doing the final part of a long journey)
- Unify davinci platforms and remove obsolete ones (Sekhar Nori, Arnd
Bergmann)"
* tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (126 commits)
ARM: sunxi: Select HAVE_ARM_ARCH_TIMER
ARM: cache-tauros2: remove ARMv6 code
ARM: mvebu: don't select CONFIG_NEON
ARM: davinci: fix DT booting with default defconfig
ARM: configs: bcm_defconfig: enable bcm590xx regulator support
ARM: davinci: remove tnetv107x support
MAINTAINERS: Update ARM STi maintainers
ARM: restrict BCM_KONA_UART to ARCH_BCM_MOBILE
ARM: bcm21664: Add board support.
ARM: sunxi: Add the new watchog compatibles to the reboot code
ARM: enable ARM_HAS_SG_CHAIN for multiplatform
ARM: davinci: remove da8xx_omapl_defconfig
ARM: davinci: da8xx: fix multiple watchdog device registration
ARM: davinci: add da8xx specific configs to davinci_all_defconfig
ARM: davinci: enable da8xx build concurrently with older devices
ARM: BCM5301X: workaround suppress fault
ARM: BCM5301X: add early debugging support
ARM: BCM5301X: initial support for the BCM5301X/BCM470X SoCs with ARM CPU
ARM: mach-bcm: Remove GENERIC_TIME
ARM: shmobile: APMU: Fix warnings due to improper printk formats
...
Add support for describing the PM8921/PM8058 RTC in device tree.
Additionally:
- drop support for describing the RTC using platform data,
as there are no current in tree users who do so.
- make allow_set_time a device-specific flag, instead of mucking
with the rtc_ops
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There have been lots of changes in ALSA core, HD-audio and ASoC, also
most of PCI drivers touched by conversions of printks. All these
resulted in a high volume and wide ranged patch sets in this release.
Many changes are fairly trivial, but also lots of nice cleanups and
refactors. There are a few new drivers, most notably, the Intel
Haswell and Baytrail ASoC driver.
Core changes:
- A bit modernization; embed the device struct into snd_card struct,
so that it may be referred from the beginning. A new snd_card_new()
function is introduced for that, and all drivers have been
converted.
- Simplification in the device management code in ALSA core;
now managed by a simple priority list instead
- Converted many kernel messages to use the standard dev_err() & co;
this would be the pretty visible difference, especially for
HD-audio.
HD-audio:
- Conexant codecs use the auto-parser as default now;
the old static code still remains in case of regressions.
Some old quirks have been rewritten with the fixups for auto-parser.
- C-Media codecs also use the auto-parser as default now, too.
- A device struct is assigned to each HD-audio codec, and the formerly
hwdep attributes are accessible over the codec sysfs, too.
hwdep attributes still remain for compatibility.
- Split the PCI-specific stuff for HD-audio controller into a separate
module, ane make a helper module for the generic controller driver.
This is a preliminary change for supporting Tegra HDMI controller in
near future, which slipped from 3.15 merge.
- Device-specific fixes: mute LED support for Lenovo Ideapad,
mic LED fix for HP laptops, more ASUS subwoofer quirks, yet more
Dell laptop headset quirks
- Make the HD-audio codec response a bit more robust
- A few improvements on Realtek ALC282 / 283 about the pop noises
- A couple of Intel HDMI fixes
ASoC:
- Lots of cleanups for enumerations; refactored lots of error prone
original codes to use more modern APIs
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues
- DPCM support for Intel Haswell and Bay Trail platforms, lots of
fixes
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC, TLV320AIC31XXX, Armada 370 DB, Cirrus cs42xx8
- Fixes for the simple-card DAI format DT mess
- DT support for a couple more devices.
- Use of the tdm_slot mapping in a few drivers
Others:
- Support of reset_resume callback for improved S4 in USB-audio driver;
the device with boot quirks have been little tested, which we need
to watch out in this development cycle
- Add PM support for ICE1712 driver (finally!);
it's still pretty partial support, only for M-Audio devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Y476
-----END PGP SIGNATURE-----
Merge tag 'sound-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been lots of changes in ALSA core, HD-audio and ASoC, also
most of PCI drivers touched by conversions of printks. All these
resulted in a high volume and wide ranged patch sets in this release.
Many changes are fairly trivial, but also lots of nice cleanups and
refactors. There are a few new drivers, most notably, the Intel
Haswell and Baytrail ASoC driver.
Core changes:
- A bit modernization; embed the device struct into snd_card struct,
so that it may be referred from the beginning. A new
snd_card_new() function is introduced for that, and all drivers
have been converted.
- Simplification in the device management code in ALSA core; now
managed by a simple priority list instead
- Converted many kernel messages to use the standard dev_err() & co;
this would be the pretty visible difference, especially for
HD-audio.
HD-audio:
- Conexant codecs use the auto-parser as default now; the old static
code still remains in case of regressions. Some old quirks have
been rewritten with the fixups for auto-parser.
- C-Media codecs also use the auto-parser as default now, too.
- A device struct is assigned to each HD-audio codec, and the
formerly hwdep attributes are accessible over the codec sysfs, too.
hwdep attributes still remain for compatibility.
- Split the PCI-specific stuff for HD-audio controller into a
separate module, ane make a helper module for the generic
controller driver. This is a preliminary change for supporting
Tegra HDMI controller in near future, which slipped from 3.15
merge.
- Device-specific fixes: mute LED support for Lenovo Ideapad, mic LED
fix for HP laptops, more ASUS subwoofer quirks, yet more Dell
laptop headset quirks
- Make the HD-audio codec response a bit more robust
- A few improvements on Realtek ALC282 / 283 about the pop noises
- A couple of Intel HDMI fixes
ASoC:
- Lots of cleanups for enumerations; refactored lots of error prone
original codes to use more modern APIs
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle
- Provide both manually and transparently locked DAPM APIs rather
than a mix of the two fixing some concurrency issues
- Start converting CODEC drivers to use separate bus interface
drivers rather than having them all in one file helping avoid
dependency issues
- DPCM support for Intel Haswell and Bay Trail platforms, lots of
fixes
- Lots of work on improvements for simple-card, DaVinci and the
Renesas rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of
the CSR SiRF SoC, TLV320AIC31XXX, Armada 370 DB, Cirrus cs42xx8
- Fixes for the simple-card DAI format DT mess
- DT support for a couple more devices.
- Use of the tdm_slot mapping in a few drivers
Others:
- Support of reset_resume callback for improved S4 in USB-audio
driver; the device with boot quirks have been little tested, which
we need to watch out in this development cycle
- Add PM support for ICE1712 driver (finally!); it's still pretty
partial support, only for M-Audio devices"
* tag 'sound-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (610 commits)
ALSA: ice1712: Add suspend support for M-Audio ICE1712-based cards
ALSA: ice1712: add suspend support for ICE1712 chip
ALSA: hda - Enable beep for ASUS 1015E
ALSA: asihpi: fix some indenting in snd_card_asihpi_pcm_new()
ALSA: hda - add headset mic detect quirks for three Dell laptops
ASoC: tegra: move AC97 clock handling to the machine driver
ASoC: simple-card: Handle many DAI links
ASoC: simple-card: Add DT documentation for multi-DAI links
ASoC: simple-card: dynamically allocate the DAI link and properties
ASoC: imx-ssi: Add .xlate_tdm_slot_mask() support.
ASoC: fsl-esai: Add .xlate_tdm_slot_mask() support.
ASoC: fsl-utils: Add fsl_asoc_xlate_tdm_slot_mask() support.
ASoC: core: remove the 'of_' prefix of of_xlate_tdm_slot_mask.
ASoC: rcar: subnode tidyup for renesas,rsnd.txt
ASoC: Remove name_prefix unset during DAI link init hack
ALSA: hda - Inform the unexpectedly ignored pins by auto-parser
ASoC: rcar: bugfix: it cares about the non-src case
ARM: bockw: fixup SND_SOC_DAIFMT_CBx_CFx flags
ASoC: pcm: Drop incorrect double/extra frees
ASoC: mfld_machine: Fix compile error
...
S2MPS14 regulators support suspend mode where their status is controlled
by PWREN coming from SoC. This patch implements the set_suspend_disable
for S2MPS14 regulators.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some newer Atom CPUs, eg Avoton and Bay Trail, use slightly different
register layouts for the iTCO than the current v1 and v2 iTCO.
Differences from previous iTCO versions include:
- The ACPI space is enabled in the "ACPI base address" register instead
of the "ACPI control register"
- The "no reboot" functionality is set in the "Power Management
Configuration" register instead of the "General Control and Status"
(GCS) register or PCI configuration space.
- The "ACPI Control Register" is not present on v3. The "Power
Management Configuration Base Address" register resides at the same
address is Avoton/Bay Trail.
To differentiate these newer chipsets create a new v3 iTCO version and
update the MFD driver to support them.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a driver for the BCM590xx PMU multi-function devices. The driver
initially supports regmap initialization and instantiation of the
voltage regulator device function of the PMU.
Signed-off-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch updates the register definitions for DA9063 to support the
production silicon variant code ID (0x5). These changes are not backwards
compatible with the previous register definitions and can only be used
with the production variant of DA9063.
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert this driver to use irqdomains so that the PMIC's child
devices can be converted to devicetree.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The pm8xxx-irq.c code is practically mandatory given that the
pm8921-core driver will WARN about it missing and the Kconfig
marks it as default y when a PM8xxx chips is enabled. The only
reason the file was split out was because we planned to support
other pm8xxx chips with different pm8xxx-core.c files. Now that
we have DT on ARM this isn't necessary because we should be able
to support all the ssbi based PM8xxx chips in one driver and one
file with no data bloat. Let's move this code into the only
driver that uses it right now (pm8921) so that it's always compiled when
needed. In the future we can rename pm8921-core.c to something
more generic.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the hash define for the new variant of the DA9053 PMIC called BC.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
All those IDs are arbitrary and so can be encapsulated into an enumeration.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the correct silicon variant code ID (0x5) to the driver. This
new code is the 'production' variant code ID for DA9063.
This patch will remove the older variant code ID which matches the
pre-production silicon ID (0x3) for the DA9063 chip.
There is also some small amount of correction done in this patch:
it splits the revision code and correctly names it according to
the hardware specification and moves the dev_info() call before
the variant ID test.
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Realtek USB card reader provides a channel to transfer command or data to flash
memory cards. This driver exports host instances for mmc and memstick subsystems
and handles basic works.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The TPS65218 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Regulators.
- Over Temperature warning and Shut down.
This patch adds support for tps65218 mfd device. At this time only
the regulator functionality is made available.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Expose some DSP registers which are useful for DSP users to be able to
access whilst debugging their firmware.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Expose some DSP registers which are useful for DSP users to be able to
access whilst debugging their firmware.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove not needed max14577-private.h header inclusion in the main driver
header. Remove obvious comment.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
