Trivial fix to spelling mistake in dev_err error message and also
split overly long line to avoid a checkpatch warning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reporting any return code for a receive buffer as an "rx error" only
produces alarming noise and the only values that have been observed to be
used in this field are not error conditions. Change this to a netdev_dbg
with a more descriptive message.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without CONFIG_PCI_IOV, we get a harmless warning about an
unused function:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:2273:13: error: 'hclge_disable_sriov' defined but not used [-Werror=unused-function]
The #ifdefs in this driver are obviously wrong, so this just
removes them and uses an IS_ENABLED() check that does the same
thing correctly in a more readable way.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiDoAAAoJEEg/ir3gV/o+594H/RH5kRwC719s/5YQFJXvGsVC
fjtj3UUJPLrWB8XBh7a4PRcxXPIHaFKJuY3MU7KHFIeZQFklJcit3njjpxDlUINo
F5S1LHBSYBkeMD/ksWBA8OLCBprNGN6WQ2tuFfAjZlQQ44zqv8LJmegoDtW9bGRy
aGAkjUmALEblQsq81y0BQwN2/8DA8HAywrs8L2dkH1LHwijoIeYMZFOtKugv1FbB
ABSKxcU7D/NYw6rsVdZG59fHFQ+eKOspDFqBZrUzfQ+zUU2hFFo96ovfXBfIqYCV
7BtJuKXu2LeGPzFLsuw4h1131iqFT1iSMy9fEhf/4OwaL/KPP/+Umy8vP/XfM+U=
=wCpd
-----END PGP SIGNATURE-----
Merge tag 'mlx5-shared-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-shared-2017-08-07
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prio is not cls_flower specific, but it is meaningful for all
classifiers. Seems that only mlxsw cares about the value. Obviously,
cls offload in other drivers is broken.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the rest offloaders of mqprio, no need to check handle.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the flows a bit in preparation of follow-up changes in
ndo_setup_tc args. Also, change the error code to align with the rest of
the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To sync-up with the naming in the rest of the driver, rename the cls arg.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let mlxsw_sp_setup_tc be a splitter for specific setup_tc types and push
out cls_flower and cls_matchall specific codes into separate functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let mlx5e_rep_setup_tc (former mlx5e_rep_ndo_setup_tc) be a splitter for
specific setup_tc types and push out cls_flower specific code into
a separate function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let mlx5e_setup_tc (former mlx5e_ndo_setup_tc) be a splitter for specific
setup_tc types and push out cls_flower and mqprio specific codes into
separate functions. Also change the return values so they are the same
as in the rest of the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let __ixgbe_setup_tc be a splitter for specific setup_tc types and push out
cls_u32 and mqprio specific codes into separate functions. Also change
the return values so they are the same as in the rest of the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let cxgb_setup_tc be a splitter for specific setup_tc types and push out
cls_u32 specific code into a separate function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this is specific to flower now, make it part of the flower offload
struct.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be aligned with the rest of the types, rename
TC_SETUP_MATCHALL to TC_SETUP_CLSMATCHALL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read new NIC capability field which represnts 16 MSBs of the max flow
counters number supported (max_flow_counter_31_16).
Backward compatibility with older firmware is preserved, the modified
driver reads max_flow_counter_31_16 as 0 from the older firmware and
uses up to 64K counters.
Changed flow counter id from 16 bits to 32 bits. Backward compatibility
with older firmware is preserved as we kept the 16 LSBs of the counter
id in place and added 16 MSBs from reserved field.
Changed the background bulk reading of flow counters to work in chunks
of at most 32K counters, to make sure we don't attempt to allocate very
large buffers.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When mlx5_ib registers itself to mlx5_core as an interface, it will
call mlx5_add_device which will call mlx5_ib interface add callback,
in case the latter successfully returns, only then mlx5_core will add
it to the interface list and async events will be forwarded to mlx5_ib.
Between mlx5_ib interface add callback and mlx5_core adding the mlx5_ib
interface to its devices list, arriving mlx5_core events can be missed
by the new mlx5_ib registering interface.
In other words:
thread 1: mlx5_ib: mlx5_register_interface(dev)
thread 1: mlx5_core: mlx5_add_device(dev)
thread 1: mlx5_core: ctx = dev->add => (mlx5_ib)->mlx5_ib_add
thread 2: mlx5_core_event: **new event arrives, forward to dev_list
thread 1: mlx5_core: add_ctx_to_dev_list(ctx)
/* previous event was missed by the new interface.*/
It is ok to miss events before dev->add (mlx5_ib)->mlx5_ib_add_device
but not after.
We fix this race by accumulating the events that come between the
ib_register_device (inside mlx5_add_device->(dev->add)) till the adding
to the list completes and fire them to the new registering interface
after that.
Fixes: f1ee87fe55 ("net/mlx5: Organize device list API in one place")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Allow to selectively build the driver with or without sriov eswitch, VF
representors and TC offloads.
Also remove the need of two ndo ops structures (sriov & basic)
and keep only one unified ndo ops, compile out VF SRIOV ndos when not
needed (MLX5_ESWITCH=n), and for VF netdev calling those ndos will result
in returning -EPERM.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Jes Sorensen <jsorensen@fb.com>
Cc: kernel-team@fb.com
Multi-Physical Function Switch (MPFs) is required for when multi-PF
configuration is enabled to allow passing user configured unicast MAC
addresses to the requesting PF.
Before this patch eswitch.c used to manage the HW MPFS l2 table,
E-Switch always (regardless of sriov) enabled vport(0) (NIC PF) vport's
contexts update on unicast mac address list changes, to populate the PF's
MPFS L2 table accordingly.
In downstream patch we would like to allow compiling the driver without
E-Switch functionalities, for that we move MPFS l2 table logic out
of eswitch.c into its own file, and provide Kconfig flag (MLX5_MPFS) to
allow compiling out MPFS for those who don't want Multi-PF support.
NIC PF netdevice will now directly update MPFS l2 table via the new MPFS
API. VF netdevice has no access to MPFS L2 table, so E-Switch will remain
responsible of updating its MPFS l2 table on behalf of its VFs.
Due to this change we also don't require enabling vport(0) (PF vport)
unicast mac changes events anymore, for when SRIOV is not enabled.
Which means E-Switch is now activated only on SRIOV activation, and not
required otherwise.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jes Sorensen <jsorensen@fb.com>
Cc: kernel-team@fb.com
Expose MLX5_VPORT_MANAGER macro to check for strict vport manager
E-switch and MPFS (Multi Physical Function Switch) abilities.
VPORT manager must be a PF with an ethernet link and with FW advertised
vport group manager capability
Replace older checks with the new macro and use it where needed in
eswitch.c and mlx5e netdev eswitch related flows.
The same macro will be reused in MPFS separation downstream patch.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove redundant call to unregister vport representor in mlx5e_add error
flow.
Hide the representor priv and eswitch internal structures from en_main.c
as preparation step for downstream patches which would allow building
the driver without support for representors and eswitch.
Fixes: 6f08a22c5f ("net/mlx5e: Register/unregister vport representors on interface attach/detach")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Since we are going to allow building the driver without eswitch support,
it would be possible to compile out the sriov netdevice ops struct such
that the basic ops instance will be used for non VF devices too.
Add missing udp tunnel ndos into mlx5e_netdev_ops_basic.
While here, rearrange some ndos in the sriov ops struct and put
vf/eswitch related ndos towards the end of it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Before the GMAC on the Anarion chip can be used, the PHY interface
selection must be configured with the DWMAC block in reset.
This layer covers a block containing only two registers. Although it
is possible to model this as a reset controller and use the "resets"
property of stmmac, it's much more intuitive to include this in the
glue layer instead.
At this time only RGMII is supported, because it is the only mode
which has been validated hardware-wise.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using Broadcom Systemport device in 32bit Platform, ifconfig can
only report up to 4G tx,rx status, which will be wrapped to 0 when the
number of incoming or outgoing packets exceeds 4G, only taking
around 2 hours in busy network environment (such as streaming).
Therefore, it makes hard for network diagnostic tool to get reliable
statistical result, so the patch is used to add 64bit support for
Broadcom Systemport device in 32bit Platform.
This patch provides 64bit statistics capability on both ethtool and ifconfig.
Signed-off-by: Jianming.qiao <kiki-good@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving PF module param console_bitmask to lio_main.c for consistency.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's supposed to be a one-to-one correspondence between the 18 macros
that #define the OCT_DEV states (in octeon_device.h) and the strings in the
oct_dev_state_str array, but there are only 14 strings in the array.
Add the missing strings (so they become 18 in total), and also revise some
incorrect/outdated text of existing strings.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for GRO (generic receive offload) for aQuantia Atlantic driver.
This results in a perfomance improvement when GRO is enabled.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rest of the helpers are named tcf_exts_*, so change the name of
the action number helpers to be aligned. While at it, change to inline
functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the __udivdi3 undefined error reported by
test robot.
Fixes: b8c17f7088 ("net: hns: Add self-adaptive interrupt coalesce support in hns driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have all the necessary IPv6 infrastructure in place, so stop
ignoring these notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without resorting to ACLs, the device performs route lookup solely based
on the destination IP address.
In case source-specific routing is needed, an error is returned and the
abort mechanism is activated, thus allowing the kernel to take over
forwarding decisions.
Instead of aborting, we can trap specific destination prefixes where
source-specific routes are present, but this will result in a lot more
code that is unlikely to ever be used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we got a replace event, then the replaced route must exist. If
the route isn't capable of multipath, then replace first matching
non-multipath capable route.
If the route is capable of multipath and matching multipath capable
route is found, then replace it. Otherwise, replace first matching
non-multipath capable route.
The new route is inserted before the replaced one. In case the replaced
route is currently offloaded, then it's overwritten in the device's table
by the new route and later deleted, thus not impacting routed traffic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow directly connected and remote unicast IPv6 routes to be programmed
to the device's tables.
As with IPv4, identical routes - sharing the same destination prefix -
are ordered in a FIB node according to their table ID and then the
metric. While the kernel doesn't share the same trie for the local and
main table, this does happen in the device, so ordering according to
table ID is needed.
Since individual nexthops can be added and deleted in IPv6, each FIB
entry stores a linked list of the rt6_info structs it represents. Upon
the addition or deletion of a nexthop, a new nexthop group is allocated
according to the new configuration and the old one is destroyed.
Identical groups aren't currently consolidated, but will be in a
follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only allow FIB offload in the presence of default rules or an l3mdev
rule. In a similar fashion to IPv4 FIB rules, sanitize IPv6 rules.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification block currently only handles IPv4 events, but we
want to start handling IPv6 events soon, so lay the groundwork now.
Do that by preparing the work item and process it according to the
notified address family.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As in previous patch, ignore IPv6 notifications since the driver doesn't
support these.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to add IPv6 notifications in the FIB notification chain, but
the driver currently doesn't support these, so ignore them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification chain is currently soley used by IPv4 code.
However, we're going to introduce IPv6 FIB offload support, which
requires these notification as well.
As explained in commit c3852ef7f2 ("ipv4: fib: Replay events when
registering FIB notifier"), upon registration to the chain, the callee
receives a full dump of the FIB tables and rules by traversing all the
net namespaces. The integrity of the dump is ensured by a per-namespace
sequence counter that is incremented whenever a change to the tables or
rules occurs.
In order to allow more address families to use the chain, each family is
expected to register its fib_notifier_ops in its pernet init. These
operations allow the common code to read the family's sequence counter
as well as dump its tables and rules in the given net namespace.
Additionally, a 'family' parameter is added to sent notifications, so
that listeners could distinguish between the different families.
Implement the common code that allows listeners to register to the chain
and for address families to register their fib_notifier_ops. Subsequent
patches will implement these operations in IPv6.
In the future, ipmr and ip6mr will be extended to provide these
notifications as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the support for two related features:
- Support for TX interrupts, with one interrupt for each CPU
- Support for different RX queue distribution modes
MVPP2_QDIST_SINGLE_MODE where a single interrupt, shared by all
CPUs, receives the RX events, and MVPP2_QDIST_MULTI_MODE, where the
per-CPU interrupts used for TX events are also used for RX events.
Since additional interrupts are needed, an update to the Device Tree
binding is needed. However, backward compatibility is preserved with
the old Device Tree binding, by gracefully degrading to the original
behavior, with only one RX interrupt, and TX completion being handled
by an hrtimer.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to the introduction of TX interrupts and improved RX
queue distribution, this commit introduces the concept of "queue
vector". A queue vector represents a number of RX and/or TX queues,
and an associated NAPI instance and interrupt.
This commit currently only creates a single queue_vector, so there are
no changes in behavior, but it paves the way for additional
queue_vector in the next commits.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 IP has a concept of "software thread", with all registers
of the PPv2.2 mapped 8 times, for concurrent accesses by 8 "software
threads". In addition, interrupts on RX queues are associated to such
"software thread".
For most cases, we map a "software thread" to the more conventional
concept of CPU, but we will soon have one exception: we will have a
model where we have one TX interrupt per CPU (each using one software
thread), and all RX events mapped to another software thread
(associated to another interrupt).
In preparation for this change, it makes sense to change the naming
from MVPP2_MAX_CPUS to MVPP2_MAX_THREADS, and plan for 8 software
threads instead of 4 currently.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the global variables rxq_number and txq_number hold the
number of per-port TXQs and RXQs. Until now, such numbers were
constant regardless of the driver configuration. As we are going to
introduce different modes for TX and RX queues, these numbers will
depend on the configuration (PPv2.1 vs. PPv2.2, exact queue
distribution logic).
Therefore, as a preparation, we move the number of RXQs and TXQs in
the 'struct mvpp2_port' structure, next to the RXQs and TXQs
descriptor arrays.
For now, they remain initialized to the same default values as
rxq_number/txq_number used to be initialized, but this will change in
future commits.
The only non-mechanical change in this patch is that the check to
verify hardware constraints on the number of RXQs and TXQs is moved
from mvpp2_probe() to mvpp2_port_probe(), since it's now in
mvpp2_port_probe() that we initialize the per-port count of RXQ and
TXQ.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX queue group allocation is anyway re-done later in
mvpp2_port_init(), so resetting it in mvpp2_init() is not very useful,
and will be annoying as we are going to rework the RX queue group
allocation logic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MVPP21_ISR_RXQ_GROUP_REG register is not indexed by rxq, but by
port, so we fix the parameter name accordingly. There are no
functional changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This operation is required for handling ioctl commands like SIOCGMIIREG,
when debugging MDIO registers from userspace.
This commit adds support for this operation.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the MAINTAINERS file with HNS3 Ethernet driver
maintainers names and other details. This also introduces the new
Makefiles required to build the HNS3 Ethernet driver and updates
the existing Kconfig file in the hisilicon folder.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
