Allow an application to enable Strong Access Ordering on specific pages of
memory on Power 7 hardware. Currently, power has a weaker memory model than
x86. Implementing a stronger memory model allows an emulator to more
efficiently translate x86 code into power code, resulting in faster code
execution.
On Power 7 hardware, storing 0b1110 in the WIMG bits of the hpte enables
strong access ordering mode for the memory page. This patchset allows a
user to specify which pages are thus enabled by passing a new protection
bit through mmap() and mprotect(). I have defined PROT_SAO to be 0x10.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This changes the oops and backtrace code to use the new %pS
printk extension to print out symbols rather than manually
calling print_symbol.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Move device_to_mask() to dma-mapping.h because we need to use it from
outside dma_64.c in a later patch.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update powerpc to use the new dma_*map*_attrs() interfaces. In doing so
update struct dma_mapping_ops to accept a struct dma_attrs and propagate
these changes through to all users of the code (generic IOMMU and the
64bit DMA code, and the iseries and ps3 platform code).
The old dma_*map_*() interfaces are reimplemented as calls to the
corresponding new interfaces.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make iommu_map_sg take a struct iommu_table. It did so before commit
740c3ce667 (iommu sg merging: ppc: make
iommu respect the segment size limits).
This stops the function looking in the archdata.dma_data for the iommu
table because in the future it will be called with a device that has
no table there.
This also has the nice side effect of making iommu_map_sg() match the
other map functions.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is dma_mask in of_device upon of_platform_device_create()
but we don't actually set coherent_dma_mask. This may cause weird
behavior of USB subsystem using of_device USB host drivers.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A recent patch to legacy_serial.c factored out some code by
using the of_match_node() facility to match a node against
an array of possible matches. However, the patch didn't properly
terminate the array causing potential crashes in cases where no
match is found. In addition, the name of the array was poorly
chosen for a static symbol making debugging harder.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updates the cputable to include the 440 processor found in the
Xilinx Virtex5 FXT FPGA.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Today's linux-next build (powerpc ppc64_defconfig) failed like this:
arch/powerpc/mm/tlb_64.c: In function 'pgtable_free_now':
arch/powerpc/mm/tlb_64.c:66: error: too many arguments to function 'smp_call_function'
arch/powerpc/kernel/machine_kexec_64.c: In function 'kexec_prepare_cpus':
arch/powerpc/kernel/machine_kexec_64.c:175: error: too many arguments to function 'smp_call_function'
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: <linuxppc-dev@ozlabs.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since Roland's ptrace cleanup starting with commit
f65255e8d5 ("[POWERPC] Use user_regset
accessors for FP regs"), the dump_task_* functions are no longer being
used.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges and cleans up some of the ugly copy/to from user code
which is required for the new fpr and vsx layout in the thread_struct.
Also fixes some hard coded buffer sizes and removes a redundant
fpr_flush_to_thread.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To allow for a single kernel image on e500 v1/v2/mc we need to fixup lwsync
at runtime. On e500v1/v2 lwsync causes an illop so we need to patch up
the code. We default to 'sync' since that is always safe and if the cpu
is capable we will replace 'sync' with 'lwsync'.
We introduce CPU_FTR_LWSYNC as a way to determine at runtime if this is
needed. This flag could be moved elsewhere since we dont really use it
for the normal CPU_FTR purpose.
Finally we only store the relative offset in the fixup section to keep it
as small as possible rather than using a full fixup_entry.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The legacy serial driver does not work with an 8250 type UART that is
described in the device tree with the reg-offset and reg-shift
properties. This change makes legacy_serial ignore these devices.
Signed-off-by: John Linn <john.linn@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This correctly hooks the VSX dump into Roland McGrath core file
infrastructure. It adds the VSX dump information as an additional elf
note in the core file (after talking more to the tool chain/gdb guys).
This also ensures the formats are consistent between signals, ptrace
and core files.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix compile error when CONFIG_VSX is enabled.
arch/powerpc/kernel/signal_64.c: In function 'restore_sigcontext':
arch/powerpc/kernel/signal_64.c:241: error: 'i' undeclared (first use in this function)
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Gcc 4.3 produced this warning:
arch/powerpc/kernel/signal_64.c: In function 'restore_sigcontext':
arch/powerpc/kernel/signal_64.c:161: warning: array subscript is above array bounds
This is caused by us copying to aliases of elements of the pt_regs
structure. Make those explicit.
This adds one extra __get_user and unrolls a loop.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch extends the floating point save and restore code to use the
VSX load/stores when VSX is available. This will make FP context
save/restore marginally slower on FP only code, when VSX is available,
as it has to load/store 128bits rather than just 64bits.
Mixing FP, VMX and VSX code will get constant architected state.
The signals interface is extended to enable access to VSR 0-31
doubleword 1 after discussions with tool chain maintainers. Backward
compatibility is maintained.
The ptrace interface is also extended to allow access to VSR 0-31 full
registers.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the macros for the VSX load/store instruction as most
binutils are not going to support this for a while.
Also add VSX register save/restore macros and vsr[0-63] register definitions.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a VSX CPU feature. Also add code to detect if VSX is available
from the device tree.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The layout of the new VSR registers and how they overlap on top of the
legacy FPR and VR registers is:
VSR doubleword 0 VSR doubleword 1
----------------------------------------------------------------
VSR[0] | FPR[0] | |
----------------------------------------------------------------
VSR[1] | FPR[1] | |
----------------------------------------------------------------
| ... | |
| ... | |
----------------------------------------------------------------
VSR[30] | FPR[30] | |
----------------------------------------------------------------
VSR[31] | FPR[31] | |
----------------------------------------------------------------
VSR[32] | VR[0] |
----------------------------------------------------------------
VSR[33] | VR[1] |
----------------------------------------------------------------
| ... |
| ... |
----------------------------------------------------------------
VSR[62] | VR[30] |
----------------------------------------------------------------
VSR[63] | VR[31] |
----------------------------------------------------------------
VSX has 64 128bit registers. The first 32 regs overlap with the FP
registers and hence extend them with and additional 64 bits. The
second 32 regs overlap with the VMX registers.
This commit introduces the thread_struct changes required to reflect
this register layout. Ptrace and signals code is updated so that the
floating point registers are correctly accessed from the thread_struct
when CONFIG_VSX is enabled.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make load_up_fpu and load_up_altivec callable so they can be reused by
the VSX code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the altivec_unavailable code, to make room at 0xf40 where the
vsx_unavailable exception will be.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We are going to change where the floating point registers are stored
in the thread_struct, so in preparation add some macros to access the
floating point registers. Update all code to use these new macros.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we set the SPE MSR bit in save_user_regs we can blow away the VEC
bit. This doesn't matter in reality as they are in fact the same bit
but looks bad.
Also, when we add VSX in a later patch, we need to be able to set two
separate MSR bits here.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use an alternative feature section in _switch. There are three cases
handled here, either we don't have an SLB, in which case we jump over the
entire code section, or if we do we either do or don't have 1TB segments.
Boot tested on Power3, Power5 and Power5+.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current feature section logic only supports nop'ing out code, this means
if you want to choose at runtime between instruction sequences, one or both
cases will have to execute the nop'ed out contents of the other section, eg:
BEGIN_FTR_SECTION
or 1,1,1
END_FTR_SECTION_IFSET(FOO)
BEGIN_FTR_SECTION
or 2,2,2
END_FTR_SECTION_IFCLR(FOO)
and the resulting code will be either,
or 1,1,1
nop
or,
nop
or 2,2,2
For small code segments this is fine, but for larger code blocks and in
performance criticial code segments, it would be nice to avoid the nops.
This commit starts to implement logic to allow the following:
BEGIN_FTR_SECTION
or 1,1,1
FTR_SECTION_ELSE
or 2,2,2
ALT_FTR_SECTION_END_IFSET(FOO)
and the resulting code will be:
or 1,1,1
or,
or 2,2,2
We achieve this by extending the existing FTR macros. The current feature
section semantic just becomes a special case, ie. if the else case is empty
we nop out the default case.
The key limitation is that the size of the else case must be less than or
equal to the size of the default case. If the else case is smaller the
remainder of the section is nop'ed.
We let the linker put the else case code in with the rest of the text,
so that relative branches from the else case are more likley to link,
this has the disadvantage that we can't free the unused else cases.
This commit introduces the required macro and linker script changes, but
does not enable the patching of the alternative sections.
We also need to update two hand-made section entries in reg.h and timex.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The logic to patch CPU feature sections lives in cputable.c, but these days
it's used for CPU features as well as firmware features. Move it into
it's own file for neatness and as preparation for some additions.
While we're moving the code, we pull the loop body logic into a separate
routine, and remove a comment which doesn't apply anymore.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A bunch of code has hard-coded the value for a "nop" instruction, it
would be nice to have a #define for it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently create_branch() creates a branch instruction for you, and
patches it into the call site. In some circumstances it would be nice
to be able to create the instruction and patch it later, and also some
code might want to check for errors in the branch creation before
doing the patching. A future commit will change create_branch() to
check for errors.
For callers that don't care, replace create_branch() with
patch_branch(), which just creates the branch and patches it directly.
While we're touching all the callers, change to using unsigned int *,
as this seems to match usage better. That allows (and requires) us to
remove the volatile in the definition of vector in powermac/smp.c and
mpc86xx_smp.c, that's correct because now that we're passing vector as
an unsigned int * the compiler knows that it's value might change
across the patch_branch() call.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We currently have a few routines for patching code in asm/system.h, because
they didn't fit anywhere else. I'd like to clean them up a little and add
some more, so first move them into a dedicated C file - they don't need to
be inlined.
While we're moving the code, drop create_function_call(), it's intended
caller never got merged and will be replaced in future with something
different.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Refactor common code between ppc32 and ppc64 module handling into a
shared filed.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the bits to the architecture-vec so that ibm,client-architecture
lets the firmware know we support the 2.06 architecture.
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add an entry for Power7 architected mode and add "(raw)" to Power7 raw
mode to distinguish it more clearly.
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a cputable entry for the POWER7 processor.
Also tell firmware that we know about POWER7.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are now two potential callers of machine_crash_shutdown,
so increase the limit accordingly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts ppc to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single().
ppc loses the timeout functionality of smp_call_function_mask() with
this change, as the generic code does not provide that.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch is based on work done by Madhvesh. R. Sulibhavi back in
March 2007.
We refactor some of the single step handling since it differs between
"classic" and "booke" powerpc cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Mark __flush_icache_range as a function that can't be probed since its
used by the kprobe code.
* Fix an issue with single stepping and async exceptions. We need to
ensure that we dont get an async exception (external, decrementer, etc)
while we are attempting to single step the probe point.
Added a check to ensure we only handle a single step if its really
intended for the instruction in question.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we have an L2CSR register (e500mc) we need to flush the L2 before going
to nap. We use the HW flush mechanism provided in that register.
The code reuses the CPU_FTR_604_PERF_MON bit as it is no longer used by
any code in the kernel. Additionally we didn't reuse the exist L2CR
feature bit as this is intended for the 7xxx L2CR register and L2CSR
is part of the new Freescale "Book-E" registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The e500 core enter DOZE/NAP power-saving modes when the core go to
cpu_idle routine.
The power management default running mode is DOZE, If the user
echo 1 > /proc/sys/kernel/powersave-nap
the system will change to NAP running mode.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Record the address of the mcount call-site. Currently all archs except sparc64
record the address of the instruction following the mcount call-site. Some
general cleanups are entailed. Storing mcount addresses in rec->ip enables
looking them up in the kprobe hash table later on to check if they're kprobe'd.
Signed-off-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Cc: davem@davemloft.net
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
KAMEZAWA Hiroyuki and Oleg Nesterov point out that since the commit
557ed1fa26 ("remove ZERO_PAGE") removed
the ZERO_PAGE from the VM mappings, any users of get_user_pages() will
generally now populate the VM with real empty pages needlessly.
We used to get the ZERO_PAGE when we did the "handle_mm_fault()", but
since fault handling no longer uses ZERO_PAGE for new anonymous pages,
we now need to handle that special case in follow_page() instead.
In particular, the removal of ZERO_PAGE effectively removed the core
file writing optimization where we would skip writing pages that had not
been populated at all, and increased memory pressure a lot by allocating
all those useless newly zeroed pages.
This reinstates the optimization by making the unmapped PTE case the
same as for a non-existent page table, which already did this correctly.
While at it, this also fixes the XIP case for follow_page(), where the
caller could not differentiate between the case of a page that simply
could not be used (because it had no "struct page" associated with it)
and a page that just wasn't mapped.
We do that by simply returning an error pointer for pages that could not
be turned into a "struct page *". The error is arbitrarily picked to be
EFAULT, since that was what get_user_pages() already used for the
equivalent IO-mapped page case.
[ Also removed an impossible test for pte_offset_map_lock() failing:
that's not how that function works ]
Acked-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Nick Piggin <npiggin@suse.de>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new e500mc core from Freescale is based on the e500v2 but with the
following changes:
* Supports only the Enhanced Debug Architecture (DSRR0/1, etc)
* Floating Point
* No SPE
* Supports lwsync
* Doorbell Exceptions
* Hypervisor
* Cache line size is now 64-bytes (e500v1/v2 have a 32-byte cache line)
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A recent commit added support for the new 440x6 and 464 cores that have the
added WL1, IL1I, IL1D, IL2I, and ILD2 bits for the caching attributes in the
TLBs. The new bits were cleared in the finish_tlb_load function, however a
similar bit of code was missed in the DataStorage interrupt vector.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are no in-tree uses of the export any more and in linux-next there
is a change that exports it globally which causes warnings:
WARNING: vmlinux: 'console_drivers' exported twice. Previous export was in vmlinux
and in one case (mpc85xx_defconfig) a build error:
kernel/built-in.o: In function `__crc_console_drivers':
(*ABS*+0x1eb0e6f5): multiple definition of `__crc_console_drivers'
So remove the export now. Also, there is no longer any need to include
linux/console.h.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
GCC 4.4.x looks to be adding support for generating out-of-line register
saves/restores based on:
http://gcc.gnu.org/ml/gcc-patches/2008-04/msg01678.html
This breaks the kernel if we enable CONFIG_CC_OPTIMIZE_FOR_SIZE. To fix
this we add the use the save/restore code from gcc and simplified it down
for our needs (integer only).
Additionally, we have to link this code into each module. The other
solution was to add EXPORT_SYMBOL() which meant going through the
trampoline which seemed nonsensical for these out-of-line routines.
Finally, we add some checks to prom_init_check.sh to ignore the
out-of-line save/restore functions.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
debugfs_create_file() returns a non-NULL (non-zero) value in case of
success, not a NULL value.
This fixes this non-critical boot-time debugging error message:
[ 1.316386] calling irq_debugfs_init+0x0/0x50
[ 1.316399] initcall irq_debugfs_init+0x0/0x50 returned -12 after 0 msecs
[ 1.316411] initcall irq_debugfs_init+0x0/0x50 returned with error code -12
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit acb0142bf0.
AMCC has indicated that the PPC 460GT does have FPU support. This
revert enables the FPU for those chips again.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
When I changed irq_alloc_host() to take an of_node
(52964f87c6: "Add an optional
device_node pointer to the irq_host"), I botched the reference
counting semantics.
Stephen pointed out that it's irq_alloc_host()'s business if
it needs to take an additional reference to the device_node,
the caller shouldn't need to care.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This eliminates this minor boot-time debugging error message:
[ 1.316451] calling add_pcspkr+0x0/0x84
[ 1.316478] initcall add_pcspkr+0x0/0x84 returned -19 after 0 msecs
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During the next merge window, pci_name()'s return value will become
const, so use the new dev_set_name() instead to avoid the warning (from
linux-next):
arch/powerpc/kernel/pci_64.c: In function 'of_create_pci_dev':
arch/powerpc/kernel/pci_64.c:193: warning: passing argument 1 of 'sprintf' discards qualifiers from pointer target type
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When building a signal or a ucontext, we can incorrectly set the MSR_VEC
bit of the kernel pt_regs->msr before returning to userspace if the task
-ever- used VMX.
This can lead to funny result if that stack used it in the past, then
"lost" it (ie. it wasn't enabled after a context switch for example)
and then called get_context. It can end up with VMX enabled and the
registers containing values from some other task.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On machines with more than one exception level any system register that
might be modified by the "normal" exception level needs to be saved and
restored on taking a higher level exception. We already are saving
and restoring ESR and DEAR.
For critical level add SRR0/1.
For debug level add CSRR0/1 and SRR0/1.
For machine check level add DSRR0/1, CSRR0/1, and SRR0/1.
On FSL Book-E parts we always save/restore the MAS registers for critical,
debug, and machine check level exceptions. On 44x we always save/restore
the MMUCR.
Additionally, we save and restore the ksp_limit since we have to adjust it
for each exception level.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
* Cleanup the code a bit my allocating an INT_FRAME on our exception
stack there by make references go from GPR11-INT_FRAME_SIZE(r8) to
just GPR11(r8)
* simplify {lvl}_transfer_to_handler code by moving the copying of the
temp registers we use if we come from user space into the PROLOG
* If the exception came from kernel mode copy thread_info flags,
preempt, and task pointer from the process thread_info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
For the additonal exception levels (critical, debug, machine check) on
40x/book-e we were using "static" allocations of the stack in the
associated head.S.
Move to a runtime allocation to make the code a bit easier to read as
we mimic how we handle IRQ stacks. Its also a bit easier to setup the
stack with a "dummy" thread_info in C code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Paul Mackerras <paulus@samba.org>
This patch cleans up the ftrace code in PowerPC based on the comments from
Michael Ellerman.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: proski@gnu.org
Cc: a.p.zijlstra@chello.nl
Cc: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: linuxppc-dev@ozlabs.org
Cc: Soeren Sandmann Pedersen <sandmann@redhat.com>
Cc: paulus@samba.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds full support for ftrace for PowerPC (both 64 and 32 bit).
This includes dynamic tracing and function filtering.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since commit "85xx: Add support for relocatable kernel (and
booting at non-zero)" (37dd2badcf),
PHYSICAL_START is #defined as kernstart_addr if RELOCATABLE
and FLATMEM is enabled.
PHYSICAL_START is used in prom_init.c and so kernstart_addr
needs to be added to the list of allowed symbols that
prom_init.c can access.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
func_descr_t->entry is already an unsigned long. Mea culpa.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This works around bugs in older binutils' objcopy.
The placement of these sections does not really matter,
but it confused the buggy old BFD libraries.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 140b932f8c ("Create modalias file
in sysfs for of_platform bus") needs this to avoid breaking the sparc
builds.
Just move the code and add whitespace around some binary operators.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This provides a way to defer processing of an interrupt that wakes the
processor out of sleep mode. On 32-bit platforms that use an
interrupt to wake the processor, we have to have interrupts enabled in
hardware at the point where we go to sleep, otherwise the processor
will never wake up. However, because interrupts are logically
disabled at this point, we don't want to process the interrupt
straight away.
This is handled by setting the _TLF_SLEEPING flag. When we get an
interrupt and _TLF_SLEEPING is set, we firstly clear the MSR_EE
(external interrupt enable) bit in the saved MSR value, and secondly
we then return to the address in the link register, like we do for
_TLF_NAPPING, but without actually handling the interrupt.
Note that this is handled somewhat differently on powerbooks, so this
new code will only be used on non-Apple machines.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make a few things static in lparcfg.c
Make init and exit routines static in rtas_flash.c
Make things static in rtas_pci.c
Make some functions static in rtas.c
Make fops static in rtas-proc.c
Remove unneeded extern for do_gtod in smp.c
Make clocksource_init() static in time.c
Make last_tick_len and ticklen_to_xs static in time.c
Move the declaration of the pvr per-cpu into smp.h
Make kexec_smp_down() and kexec_stack static in machine_kexec_64.c
Don't return void in arch_teardown_msi_irqs() in msi.c
Move declaration of GregorianDay()into asm/time.h
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We use the low bits of regs->trap as flag bits. We already indicate
critical and machine check level exceptions via this mechanism. Extend it
to indicate debug level exceptions.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Replace TIF_RESTORE_SIGMASK with TLF_RESTORE_SIGMASK and define
our own set_restore_sigmask() function. This saves the costly
SMP-safe set_bit operation, which we do not need for the sigmask
flag since TIF_SIGPENDING always has to be set too.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 76bc080ef5 ("POWERPC] Make default
cputable entries reflect selected CPU family") added default entries
for the e200 and e500 families, but missed a closing brace on those
entries, as pointed out by David Gibson. This adds the closing braces.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This printk() appears twice in the same function. Only the latter one
in the inval_range: section appears to be legitimate.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove duplicate #include of <asm/prom.h> in
arch/powerpc/kernel/btext.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves lockdep_init() to before udbg_early_init() as the later
can call things that acquire spinlocks etc... This also makes printk
safer to use earlier.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When debugging early boot problems, it's common to sprinkle printk's
all over the place. However, on 64-bit powerpc, this can lead to
memory corruption if done too early due to the PACA pointer and
lockdep core not being initialized.
This adds some comments to early_setup() that document when it is
safe to do so in order to save time for whoever has to debug that
stuff next.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When doing lockdep, I had two patches to initialize paca->_current
early, one bogus, and one correct. Unfortunately both got merged
as the bad one ended up being part of the main lockdep patch by
mistake. This causes memory corruption at boot. This removes
the offending code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Changes the cputable so that various CPU families that have an exclusive
CONFIG_ option have a more sensible default entry to use if the specific
processor hasn't been identified.
This makes the kernel more generally useful when booted on an unknown
PVR for things like new 4xx variants.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new 440x6 core used on AMCC 460EX/GT introduces new storage attibure
fields to the TLB2 word. Those are:
Bit 11 12 13 14 15
WL1 IL1I IL1D IL2I IL2D
With these bits the cache (L1 and L2) can be configured in a more flexible
way, instruction- and data-cache independently now. The "old" I and W bits
are still available and setting these old bits will automically set these
new bits too (for backward compatibilty).
The current code does not clear these fields resulting in disabling the cache
by chance. This patch now makes sure that these new bits are cleared when
the TLB2 word is written.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This replaces the duplicated arch-specific versions of "sys_pipe()" with
one unified implementation. This removes almost 250 lines of duplicated
code.
It's marked __weak, so that *if* an architecture wants to override the
default implementation it can do so by simply having its own replacement
version, since many architectures use alternate calling conventions for
the 'pipe()' system call for legacy reasons (ie traditional UNIX
implementations often return the two file descriptors in registers)
I still haven't changed the cris version even though Linus says the BKL
isn't needed. The arch maintainer can easily do it if there are really
no obstacles.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
This fixes a regression reported by Kamalesh Bulabel where a POWER4
machine would crash because of an SLB miss at a point where the SLB
miss exception was unrecoverable. This regression is tracked at:
http://bugzilla.kernel.org/show_bug.cgi?id=10082
SLB misses at such points shouldn't happen because the kernel stack is
the only memory accessed other than things in the first segment of the
linear mapping (which is mapped at all times by entry 0 of the SLB).
The context switch code ensures that SLB entry 2 covers the kernel
stack, if it is not already covered by entry 0. None of entries 0
to 2 are ever replaced by the SLB miss handler.
Where this went wrong is that the context switch code assumes it
doesn't have to write to SLB entry 2 if the new kernel stack is in the
same segment as the old kernel stack, since entry 2 should already be
correct. However, when we start up a secondary cpu, it calls
slb_initialize, which doesn't set up entry 2. This is correct for
the boot cpu, where we will be using a stack in the kernel BSS at this
point (i.e. init_thread_union), but not necessarily for secondary
cpus, whose initial stack can be allocated anywhere. This doesn't
cause any immediate problem since the SLB miss handler will just
create an SLB entry somewhere else to cover the initial stack.
In fact it's possible for the cpu to go quite a long time without SLB
entry 2 being valid. Eventually, though, the entry created by the SLB
miss handler will get overwritten by some other entry, and if the next
access to the stack is at an unrecoverable point, we get the crash.
This fixes the problem by making slb_initialize create a suitable
entry for the kernel stack, if we are on a secondary cpu and the stack
isn't covered by SLB entry 0. This requires initializing the
get_paca()->kstack field earlier, so I do that in smp_create_idle
where the current field is initialized. This also abstracts a bit of
the computation that mk_esid_data in slb.c does so that it can be used
in slb_initialize.
Signed-off-by: Paul Mackerras <paulus@samba.org>
As TICK_LENGTH_SHIFT is used for more than just the tick length, the name
isn't quite approriate anymore, so this renames it to NTP_SCALE_SHIFT.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This changes time_freq to a 64bit value and makes it static (the only outside
user had no real need to modify it). Intermediate values were already 64bit,
so the change isn't that big, but it saves a little in shifts by replacing
SHIFT_NSEC with TICK_LENGTH_SHIFT. PPM_SCALE is then used to convert between
user space and kernel space representation.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a minimalistic braille screen reader support. This is meant to
be used by blind people e.g. on boot failures or when / cannot be mounted
etc and thus the userland screen readers can not work.
[akpm@linux-foundation.org: fix exports]
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jiri Kosina <jikos@jikos.cz>
Cc: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit edd8ce6743 (Use extended crashkernel
command line on ppc64), changed the logic in reserve_crashkernel()
which deals with the crashkernel= command line option.
This introduced a bug in the case when there is no crashkernel= option,
or it is incorrect. We would fall through and calculate the crash_size
based on the existing values in crashk_res. If both start and end are 0,
the default, we calculate the crash_size as 1 byte - which is wrong.
Rework the logic so that we use crashk_res, regardless of whether it's
set by the command line or via the device tree (see prom.c). Then check
if we have an empty range (end == start), and if so make sure to set
both end and start to zero (this is checked in machine_kexec_64.c). Then
we calculate the crash_size once we know we have a non-zero range.
Finally we always want to warn the user if they specify a base != 32MB,
so remove the special case for that in the command line parsing case.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current_thread_info() macro, used by preempt_count(), assumes the
base address and size of the stack are THREAD_SIZE aligned.
The emergency stack currently isn't either of these things, which
could potentially cause problems anytime we're running on the
emergency stack. That includes when we detect a bad kernel stack
pointer, and also during early_setup_secondary().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[RAPIDIO] Change RapidIO doorbell source and target ID field to 16-bit
[RAPIDIO] Add RapidIO connection info print out and re-training for broken connections
[RAPIDIO] Add serial RapidIO controller support, which includes MPC8548, MPC8641
[RAPIDIO] Add RapidIO node probing into MPC86xx_HPCN board id table
[RAPIDIO] Add RapidIO node into MPC8641HPCN dts file
[RAPIDIO] Auto-probe the RapidIO system size
[RAPIDIO] Add OF-tree support to RapidIO controller driver
[RAPIDIO] Add RapidIO multi mport support
[RAPIDIO] Move include/asm-ppc/rio.h to asm-powerpc
[RAPIDIO] Add RapidIO option to kernel configuration
[RAPIDIO] Change RIO function mpc85xx_ to fsl_
[POWERPC] Provide walk_memory_resource() for powerpc
[POWERPC] Update lmb data structures for hotplug memory add/remove
[POWERPC] Hotplug memory remove notifications for powerpc
[POWERPC] windfarm: Add PowerMac 12,1 support
[POWERPC] Fix building of pmac32 when CONFIG_NVRAM=m
[POWERPC] Add IRQSTACKS support on ppc32
[POWERPC] Use __always_inline for xchg* and cmpxchg*
[POWERPC] Add fast little-endian switch system call
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use proc_create()/proc_create_data() to make sure that ->proc_fops and ->data
be setup before gluing PDE to main tree.
Add correct ->owner to proc_fops to fix reading/module unloading race.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This initializes the RapidIO controller driver using addresses and
interrupt numbers obtained from the firmware device tree, rather than
using hardcoded constants.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes it possible to use separate stacks for hard and soft IRQs
on 32-bit powerpc as well as on 64-bit. The code for 32-bit is just
the 32-bit analog of the 64-bit code.
* Added allocation and initialization of the irq stacks. We limit the
stacks to be in lowmem for ppc32.
* Implemented ppc32 versions of call_do_softirq() and call_handle_irq()
to switch the stack pointers
* Reworked how we do stack overflow detection. We now keep around the
limit of the stack in the thread_struct and compare against the limit
to see if we've overflowed. We can now use this on ppc64 if desired.
[ paulus@samba.org: Fixed bug on 6xx where we need to reload r9 with the
thread_info pointer. ]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a system call on 64-bit platforms for switching between
little-endian and big-endian modes that is much faster than doing a
prctl call. This system call is handled as a special case right at
the start of the system call entry code, and because it is a special
case, it uses a system call number which is out of the range of
normal system calls, namely 0x1ebe.
Measurements with lmbench on a 4.2GHz POWER6 showed no measurable
change in the speed of normal system calls with this patch.
Switching endianness with this new system call takes around 60ns on a
4.2GHz POWER6, compared with around 300ns to switch endian mode with a
prctl. This can provide a significant performance advantage for
emulators for little-endian architectures that want to switch between
big-endian and little-endian mode frequently, e.g. because they are
generating instructions sequences on the fly and they want to run
those sequences in little-endian mode.
The other thing about this system call is that it doesn't clobber as
many registers as a normal system call. It only clobbers r12.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This functionality is definitely experimental, but is capable of running
unmodified PowerPC 440 Linux kernels as guests on a PowerPC 440 host. (Only
tested with 440EP "Bamboo" guests so far, but with appropriate userspace
support other SoC/board combinations should work.)
See Documentation/powerpc/kvm_440.txt for technical details.
[stephen: build fix]
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The AMCC 460GT doesn't have an FPU so let's not enable support for it.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This splits cell io-workaround code into spider-pci dependent code and
a generic part, and also moves io-workarounds initialization into
cell_setup_phb.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The udbg console should be safe to call basically at any time after boot.
It does not need any per-cpu resources or for the cpu to be online, as
long as there is a udbg_putc routine hooked up it should work. So mark it
as CON_ANYTIME.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because the udbg_console has CON_ENABLED set, it's possible that when we
register it with the console code the index won't be set. This leads to
slightly confusing boot messages like:
[ 0.000000] console [udbg-1] enabled
We could remove CON_ENABLED, but we don't want to do that, we always
want the udbg console to be activated, even if the user specified some
other console on the command line.
The simplest fix seems to be just to set the index to 0 by hand. There
is no issue with duplicate udbg consoles, as we guard against registering
multiple times in register_early_udbg_console().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the required functionality to fill in all pacas at runtime.
With NR_CPUS=1024
text data bss dec hex filename
137 1704032 0 1704169 1a00e9 arch/powerpc/kernel/paca.o :Before
121 1179744 524288 1704153 1a00d9 arch/powerpc/kernel/paca.o :After
Also remove unneeded #includes from arch/powerpc/kernel/paca.c
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Removed get_msr(), get_srr0(), and get_srr1() - not used anywhere
* Use STACK_FRAME_OVERHEAD instead of magic number
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As BenH said the other day, it is an "accident" that prom_init.o is
linked with the rest of the kernel. The truth is a little more
subtle, prom_init isn't truly bootloader, it does access kernel data
in a few places.
What we can do is discourage people from adding new code that accesses
data outside of prom_init. And hence this patch; from the script:
# This script checks prom_init.o to see what external symbols it
# is using, if it finds symbols not in the whitelist it returns
# an error. The point of this is to discourage people from
# intentionally or accidentally adding new code to prom_init.c
# which has side effects on other parts of the kernel.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Removed TI_EXECDOMAIN define as its not used anywhere
* Use STACK_INT_FRAME_SIZE to allow common define of INT_FRAME_SIZE
* Define TI_CPU on both ppc32 & ppc64 (removes an ifdef).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use (31-THREAD_SHIFT) to get to thread_info from stack pointer. This makes
the code a bit easier to read and more robust if we ever change THREAD_SHIFT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the inclusion of asm-offsets.h from stacktrace.c. It isn't
supposed to be included in C code and it causes problems with multiple
definitions of things.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added support to allow an 85xx kernel to be run from a non-zero physical
address (useful for cooperative asymmetric multiprocessing situations and
kdump). The support can be configured at compile time by setting
CONFIG_PAGE_OFFSET, CONFIG_KERNEL_START, and CONFIG_PHYSICAL_START as
desired.
Alternatively, the kernel build can set CONFIG_RELOCATABLE. Setting this
config option causes the kernel to determine at runtime the physical
addresses of CONFIG_PAGE_OFFSET and CONFIG_KERNEL_START. If
CONFIG_RELOCATABLE is set, then CONFIG_PHYSICAL_START has no meaning.
However, CONFIG_PHYSICAL_START will always be used to set the LOAD program
header physical address field in the resulting ELF image.
Currently we are limited to running at a physical address that is a
multiple of 256M. This is due to how we map TLBs to cover
lowmem. This should be fixed to allow 64M or maybe even 16M alignment
in the future. It is considered an error to try and run a kernel at a
non-aligned physical address.
All the magic for this support is accomplished by proper initialization
of the kernel memory subsystem and use of ARCH_PFN_OFFSET.
The use of ARCH_PFN_OFFSET only affects normal memory and not IO mappings.
ioremap uses map_page and isn't affected by ARCH_PFN_OFFSET.
/dev/mem continues to allow access to any physical address in the system
regardless of how CONFIG_PHYSICAL_START is set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc kernel stacks need to be naturally aligned, as they
contain the thread info at the bottom, which is obtained by
clearing the low bits of the stack pointer.
However, when using 64K pages, the stack is smaller than a page,
so we use kmalloc to allocate it, but that doesn't provide the
alignment guarantee we need.
It appeared to work so far... until one enables SLUB debugging
which then returns unaligned pointers. Ooops...
This fixes it by using a slab cache with enforced alignment. It
relies on my previous patch that adds a thread_info_cache_init()
callback.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This reverts commit e4cc58944c, as
requested by Roland McGrath, because compat_ptrace_request (added in
commit e16b278164, "ptrace:
compat_ptrace_request siginfo") now handles this case.
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
603 CPUs have the same issue that some 750 CPUs have in that they can crash
in funny ways if a store from an FPU register instruction is executed on a
register that has never been initialized since power on. This patch fixes
it by making sure all FP registers have been properly initialized at kernel
boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the generic pci_enable_resources() instead of the arch-specific code.
The generic version is functionally equivalent, but uses dev_printk.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Define the copy_siginfo_from_user32 entry point for powerpc, so
that generic CONFIG_COMPAT code can call it. We already had the
code rolled into compat_sys_rt_sigqueueinfo, this just moves it
out into the canonical function that other arch's define.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Current versions of gdb require a working implementation of
PTRACE_GETSIGINFO for proper watchpoint support. Since struct siginfo
contains pointers it must be converted when passed to a 32-bit debugger.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
This adds the low level irq tracing hooks to the powerpc architecture
needed to enable full lockdep functionality.
This is partly based on Johannes Berg's initial version. I removed
the asm trampoline that isn't needed (thus improving performance) and
modified all sorts of bits and pieces, reworking most of the assembly,
etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds stacktrace support for powerpc, which will be needed for
lockdep.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves various definitions used all over the place to parse stack
frames to ptrace.h so only one definition is needed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Lockdep found out that we can occasionally take the device-tree
lock for reading from softirq time (from rtas_token called
by the rtas real time clock code called by the NTP code),
while we take it occasionally for writing without masking
interrupts. The combination of those two can thus deadlock.
While some of those cases of interrupt read lock could be fixed
(such as caching the RTAS tokens) I figured that taking the
lock for writing is so rare (device-tree modification) that we
may as well penalize that case and allow reading from interrupts.
Thus, this turns all the writers to take the lock with irqs
masked to avoid the situation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Add special cases for pplus and prep to ide_default_{irq,io_base}()
(+ FIXMEs about the need to use IDE platform host driver instead).
* Remove no longer needed ppc_ide_md and struct ide_machdep_calls.
* Then remove <linux/ide.h> include from:
- arch/powerpc/kernel/setup_32.c
- arch/ppc/kernel/ppc_ksyms.c
- arch/ppc/kernel/setup.c
- arch/ppc/platforms/pplus.c
- arch/ppc/platforms/prep_setup.c
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
global_dbcr0 needs to be a per cpu set of save areas instead of a single
global on all processors.
Also, we switch to using DBCR0_IDM to determine if the user space app is
being debugged as its a more consistent way. In the future we should
support features like hardware breakpoint and watchpoints which will
have DBCR0_IDM set but not necessarily DBCR0_IC (single step).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The architecture allows for "Book-E" style debug interrupts to either go
to critial interrupts of their own debug interrupt level. To allow for
a dynamic kernel to support machines of either type we want to be able to
compile in the interrupt handling code for both exception levels.
Towards this goal we renamed the debug handling macros to specify the
interrupt level in their name (DEBUG_CRIT_EXCEPTION/DebugCrit and
DEBUG_DEBUG_EXCEPTION/DebugDebug).
Additionally, on the Freescale Book-e parts we expanded the exception
stacks to cover the maximum case of needing three exception stacks (normal,
machine check and debug).
There is some kernel text space optimization to be gained if a kernel is
configured for a specific Freescale implementation but we aren't handling
that now to allow for the single kernel image support.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This changes the way we calculate how much space to reserve for the
pHyp dump. Currently we reserve 256MB only. With this change, the
code first checks to see if an amount has been specified on the boot
command line with the "phyp_dump_reserve_size" option, and if so, uses
that much.
Otherwise it computes 5% of total ram and rounds it down to a multiple
of 256MB, and uses the larger of that or 256MB.
This is for large systems with a lot of memory (10GB or more). The
aim is to have more space available for the kernel on reboot on
machines with more resources. Although the dump will be collected
pretty fast and the memory released really early on allowing the
machine to have the full memory available, this alleviates any issues
that can be caused by having way too little memory on very very large
systems during those few minutes.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can set LOAD_OFFSET and use the AT attribute on sections and the
linker will properly set the physical address of the LOAD program
header for us.
This allows us to know how the PHYSICAL_START the user configured a
kernel with by just looking at the resulting vmlinux ELF.
This is pretty much stolen from how x86 does things in their linker
scripts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* PAGE_OFFSET is not always the start of code, use _stext instead.
* grab PAGE_SIZE and KERNELBASE from asm/page.h like ppc64 does. Makes the
code a bit more common and provide a single place to manipulate the
defines for things like kdump.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Determine the RPN we are running the kernel at runtime rather
than using compile time constant for initial TLB
* Cleanup adjust_total_lowmem() to respect memstart_addr and
be a bit more clear on variables that are sizes vs addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fedora 9 works on Efika without the separate 'device-tree supplement',
thanks to the kernel's own fixups. With one exception -- because 'CHRP'
still appears on the 'machine:' line in /proc/cpuinfo, the installer
misdetects the platform and misconfigures yaboot, putting it into a PReP
boot partition instead of in the /boot filesystem where the Efika's
firmware could find it.
The kernel's fixups for Efika already correct one instance of 'chrp', in
the 'device_type' property. This fixes it in the 'CODEGEN,description'
property too, since that's what's exposed to userspace in /proc/cpuinfo.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the handling of the preempt count when switching
interrupt stacks so that HW interrupt properly get the softirq
mask copied over from the previous stack.
It also initializes the softirq stack preempt_count to 0 instead
of SOFTIRQ_OFFSET, like x86, as __do_softirq() does the increment,
and we hit some lockdep checks if we have it twice.
That means we do run for a little while off the softirq stack
with the preempt-count set to 0, which could be deadly if we
try to take a softirq at that point, however we do so with
interrupts disabled, so I think we are ok.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, we initialize the "current" pointer in the PACA (which
is used by the "current" macro in the kernel) before calling
setup_system(). That means that early_setup() is called with
current still "NULL" which is -not- a good idea. It happens to
work so far but breaks with lockdep when early code calls printk.
This changes it so that all PACAs are statically initialized with
__current pointing to the init task. For non-0 CPUs, this is fixed
up before use.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we have the alpaca, the reg_save_ptr is no longer needed in the
paca. Eradicate all global uses of it and make it static in the iSeries
lpardata.c
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The iSeries HV only needs the first two fields of the paca statically
initialised, so create an alternate paca that contains only those and
switch to our real paca immediately after boot.
This is in order to make the 1024 cpu patches easier since they will no
longer have to statically initialise the pacas for iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an SLB miss interrupt happens while the RI bit of MSR is zero, we
can't just return, because RI being zero indicates that SRR0/SRR1
potentially had live values in them, and the process of taking an
interrupt overwrites them.
This should never happen, but if it does, we try to print a nice oops
message. That doesn't work, however, because the code at unrecov_slb
assumes that the MMU has been turned on, but we call it with the MMU
off (and have done so since the SLB miss handler was rewritten to run
without turning the MMU on) -- except on iSeries, where everything runs
with the MMU on.
This fixes it by adding the necessary code to turn the MMU on if
necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A couple of places are duplicating the function of
of_device_is_available; convert them to use it.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have an assembly version of strncmp for the bootwrapper, but not
for the kernel, so we end up using the C version in the kernel. This
takes the strncmp code from the bootup and copies it to the kernel
proper, adding two instructions so it copes correctly with len==0.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Handling of the proc_dir_entry->count was changed in 2.6.24-rc5.
After this change, the default value for pde->count is 1 and not 0 as
before. Therefore, if we want to check whether our procfs file is
already opened (already in use), we have to check if pde->count is
greater than 2 rather than 1.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A subtle bug sneaked into iSeries recently. On this platform, we must
not normally clear MSR:EE (the hardware external interrupt enable)
except for short periods of time. Taking an interrupt while
soft-disabled doesn't cause us to clear it for example.
The iSeries kernel expects to mostly run with MSR:EE enabled at all
times except in a few exception entry/exit code paths. Thus
local_irq_enable() doesn't check if it needs to hard-enable as it
expects this to be unnecessary on iSeries.
However, hard_irq_disable() _does_ cause MSR:EE to be cleared,
including on iSeries. A call to it was recently added to the
context switch code, thus causing interrupts to become disabled
for a long periods of time, causing the iSeries watchdog to kick
in under some circumstances and other nasty things.
This patch fixes it by making local_irq_enable() properly re-enable
MSR:EE on iSeries. It basically removes a return statement here
to make iSeries use the same code path as everybody else. That does
mean that we might occasionally get spurious decrementer interrupts
but I don't think that matters.
Another option would have been to make hard_irq_disable() a nop
on iSeries but I didn't like it much, in case we have good reasons
to hard-disable.
Part of the patch is fixes to make sure the hard_enabled PACA field
is properly set on iSeries as it used not to be before, since it
was mostly unused.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Old-world powermacs don't set L2CR or L3CR on processor upgrade cards.
This simple patch allows the setting of L3CR via a kernel parameter
(like the existing kernel parameter to set L2CR).
Signed-off-by: Robert Brose <bob@qbjnet.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x1e4c0): Section mismatch in reference from the
function .move_device_tree() to the function .init.text:.lmb_alloc_base()
The function .move_device_tree() references
the function __init .lmb_alloc_base().
This is often because .move_device_tree lacks a __init
annotation or the annotation of .lmb_alloc_base is wrong.
move_device_tree() is called from early_init_devtree() only, which is __init
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is a bug in the powerpc DABR (data access breakpoint) handling,
which can result in us missing breakpoints if several threads are trying
to break on the same address.
The circumstances are that do_page_fault() calls do_dabr(), this clears
the DABR (sets it to 0) and sets up the signal which will report to
userspace that the DABR was hit. The do_signal() code will restore the DABR
value on the way out to userspace.
If we reschedule before calling do_signal(), __switch_to() will check the
cached DABR value and compare it to the new thread's value, if they match
we don't set the DABR in hardware.
So if two threads have the same DABR value, and we schedule from one to
the other after taking the interrupt for the first thread hitting the DABR,
the second thread will run without the DABR set in hardware.
The cleanest fix is to move the cache update into set_dabr(), that way we
can't forget to do it.
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds basic support for the AMCC 460EX/460GT PPC's to arch/powerpc.
Currently those PPC's are still based on a 440 core and *not* a 460 core.
Here some basic features of those SoC's:
460EX:
- Up to 1.2GHz, 32kB L1 I-cache and D-cache, 256kB L2-cache, FPU
- 1 * PCI (max 66MHz), 2 * PCIe (one 4-lane, one 1-lane)
- 2 * GBit Ethernet with TCP/IP acceleration
- USB 2.0 Host/Device OTG and Host interface
- SATA controller
- Optional security feature
460GT (only changes to 460EX):
- 4 * GBit Ethernet with TCP/IP acceleration
- RapidIO
- No SATA
- No USB
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a kernel command line option "phyp_dump", which takes a 0/1
value for disabling/ enabling phyp_dump at boot time. Kdump can use
this on cmdline (phyp_dump=0) to disable phyp-dump during boot when
enabling itself. This will ensure only one dumping mechanism is active
at any given time.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Initial patch for reserving memory in early boot, and freeing it
later. If the previous boot had ended with a crash, the reserved
memory would contain a copy of the crashed kernel data.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These items in asm-offsets.c are not used anywhere. This removes them.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PT_DTRACE flag is meaningless and obsolete.
Don't touch it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It was being protected by CONFIG_PPC32, but we want to export it on
64-bit also. This moves it out of the ifdef.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Print out 'model' property of '/' node as a machine name
in generic show_cpuinfo() routine.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the PMU is an NMI now, it can come at any time we are only soft
disabled. We must hard disable around the two places we allow the kernel
stack SLB and r1 to go out of sync. Otherwise the PMU exception can
force a kernel stack SLB into another slot, which can lead to it
getting evicted, which can lead to a nasty unrecoverable SLB miss
in the exception entry code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PTRACE_SETREGS request was only recently added on powerpc,
and gdb does not use it. So it slipped through without getting
all the testing it should have had.
The user_regset changes had a simple bug in storing to all of
the 32-bit general registers block on 64-bit kernels. This bug
only comes up with PTRACE_SETREGS, not PPC_PTRACE_SETREGS.
It causes a BUG_ON to hit, so this fix needs to go in ASAP.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Once again, this time with feeling....
- Ted
>From c91cfaabc17f8a53807a2f31f067a732e34a1550 Mon Sep 17 00:00:00 2001
From: Theodore Ts'o <tytso@mit.edu>
Date: Wed, 12 Mar 2008 11:50:39 -0400
Subject: Export empty_zero_page
The empty_zero_page symbol is exported by most other architectures
(s390, ia64, x86, um), and an upcoming ext4 patch needs it because
ZERO_PAGE() references empty_zero_page, and we need it to zero out an
unitialized extents in ext4 files.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A bogus test for unassigned resources that came from our 32-bit
PCI code ended up being "merged" by my previous patch series,
breaking some 64-bit setups where devices have legal resources
ending at 0xffffffff.
This fixes it by completely changing the test. We now test for
res->start == 0, as the generic code expects, and we also only
do so on platforms that don't have the PPC_PCI_PROBE_ONLY flag
set, as there are cases of pSeries and iSeries where it could
be a valid value and those can't reassign devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers (such as V4L2) have code that causes gcc to generate
calls to __ucmpdi2 when compiling for 32-bit powerpc, which results
in either a link-time error or a module that can't be loaded, as
we don't currently have a __ucmpdi2. This adds one so these drivers
can be used.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes swap routines operate correctly on the ppc_8xx based machines.
Code has been revalidated on mpc885ads (8M sdram) with recent kernel. Based
on patch from Yuri Tikhonov <yur@emcraft.com> to do the same on arch/ppc
instance.
Recent kernel's size makes swap feature very important on low-memory platforms,
those are actually non-operable without it.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This code isn't referenced anywhere, so remove it.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dt_mem_next_cell() currently does of_read_ulong(). This does not
allow for the case where #size-cells and/or #address-cells = 2 on a
32-bit system, as it will end up reading 32 bits instead of the
expected 64. Change it to use of_read_number instead and always
return a u64.
Signed-off-by: Becky Bruce <becky.bruce at freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix sparse warnings in powerpc kprobes:
CHECK arch/powerpc/kernel/kprobes.c
arch/powerpc/kernel/kprobes.c:277:6: warning: symbol 'kretprobe_trampoline_holder' was not declared. Should it be static?
arch/powerpc/kernel/kprobes.c:287:15: warning: symbol 'trampoline_probe_handler' was not declared. Should it be static?
arch/powerpc/kernel/kprobes.c:525:16: warning: symbol 'jprobe_return_end' was not declared. Should it be static?
Fix along the same lines as http://lkml.org/lkml/2008/2/13/642
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the following section mismatches:
<-- snip -->
...
WARNING: vmlinux.o(.text+0xe49c): Section mismatch in reference from the function .vdso_do_func_patch64() to the function .init.text:.find_symbol64()
WARNING: vmlinux.o(.text+0xe4d0): Section mismatch in reference from the function .vdso_do_func_patch64() to the function .init.text:.find_symbol64()
WARNING: vmlinux.o(.text+0xe56c): Section mismatch in reference from the function .vdso_do_func_patch32() to the function .init.text:.find_symbol32()
WARNING: vmlinux.o(.text+0xe5a0): Section mismatch in reference from the function .vdso_do_func_patch32() to the function .init.text:.find_symbol32()
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc show_regs prints CPU using smp_processor_id: change that to
raw_smp_processor_id, so that when it's showing a WARN_ON backtrace without
preemption disabled, DEBUG_PREEMPT doesn't mess up that warning with its own.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit ad7f71674a ("[POWERPC] Use a
sensible default for clock_getres() in the VDSO") corrected the clock
resolution reported by the VDSO clock_getres() but introduced another
problem in that older versions of gcc (gcc-4.0 and earlier) fail to
compile the new code in arch/powerpc/kernel/asm-offsets.c.
This fixes it by introducing a new MONOTONIC_RES_NSEC define in the
generic code which is equivalent to KTIME_MONOTONIC_RES but is just an
integer constant, not a ktime union.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the SPE register data appear in ELF core dumps, using the
new n_type value NT_PPC_SPE (0x101). This new note type is not used
by any consumers of core files yet, but support can be added. I don't
even have any hardware with SPE capabilities, so I've never seen such
a note. But this demonstrates how simple it is to export register
information in core dumps when the user_regset style is used for the
low-level code.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up the 32-bit ptrace syscall support to use user_regset calls
to get at the register data for PTRACE_*REGS* calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This replaces powerpc's compat_sys_ptrace with a compat_arch_ptrace and
enables the new generic definition of compat_sys_ptrace instead.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes some duplicated code by calling the new generic
compat_ptrace_request from powerpc's compat_sys_ptrace.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that ptrace_request handles these, we can drop some more boilerplate.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This replaces all the code for powerpc PTRACE_*REGS* requests with
simple calls to copy_regset_from_user and copy_regset_to_user. All
the ptrace formats are either the whole corresponding user_regset
format (core dump format) or a leading subset of it, so we can get
rid of all the remaining embedded knowledge of both those layouts
and of the internal data structures they correspond to. Only the
user_regset accessors need to implement that.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This switches the CONFIG_PPC64 support for 32-bit ELF to use the
generic fs/compat_binfmt_elf.c implementation instead of our own
binfmt_elf32.c. Since so much is the same between 32/64, there is
only one macro we have to define to make the generic support work out
of the box.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This extends task_user_regset_view CONFIG_PPC64 with support for the
32-bit view of register state, compatible with what a CONFIG_PPC32
kernel provides. This will enable generic machine-independent code to
access user-mode threads' registers for debugging and dumping.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This provides the task_user_regset_view entry point and support for
all the native-mode (64 on CONFIG_PPC64, 32 on CONFIG_PPC32) thread
register state. This will enable generic machine-independent code to
access user-mode threads' registers for debugging and dumping.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements user_regset-style accessors for the powerpc general
registers. In the future these functions will be the only place that
needs to understand the user_regset layout (core dump format) and how
it maps to the internal representation of user thread state.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This isolates the ptrace code for the special-case registers msr and trap
from the ptrace-layout dispatch code. This should inline away completely.
It cleanly separates the low-level machine magic that has to be done for
deep reasons, from the superficial details of the ptrace interface.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements user_regset-style accessors for the powerpc SPE data,
and rewrites the existing ptrace code in terms of those calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements user_regset-style accessors for the powerpc Altivec data,
and rewrites the existing ptrace code in terms of those calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements user_regset-style accessors for the powerpc FPU data,
and rewrites the existing ptrace code in terms of those calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Looks like "[POWERPC] kdump shutdown hook support" broke builds when
CONFIG_DEBUGGER=n and CONFIG_KEXEC=y, such as in g5_defconfig:
arch/powerpc/kernel/crash.c: In function 'default_machine_crash_shutdown':
arch/powerpc/kernel/crash.c:388: error: '__debugger_fault_handler' undeclared (first use in this function)
arch/powerpc/kernel/crash.c:388: error: (Each undeclared identifier is reported only once
arch/powerpc/kernel/crash.c:388: error: for each function it appears in.)
Move the debugger hooks to under CONFIG_DEBUGGER || CONFIG_KEXEC, since
that's when the crash code is enabled.
(I should have caught this with my build-script pre-merge, my bad. :( )
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the ability to scale cputime into generic code. This allows us
to fix the issue in kernel/timer.c (noticed by Balbir) where we could only
add an unscaled value to the scaled utime/stime.
This adds a cputime_to_scaled function. As before, the POWERPC version
does the scaling based on the last SPURR/PURR ratio calculated. The
generic and s390 (only other arch to implement asm/cputime.h) versions are
both NOPs.
Also moves the SPURR and PURR snapshots closer.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: Jay Lan <jlan@engr.sgi.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The e300 c3 and c4 variants support hardware performance monitor counters
which are identical to those found in the e500.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some of the more recent e300 cores have the same performance monitor
implementation as the e500. e300 isn't book-e, so the name isn't
really appropriate. In preparation for e300 support, rename a bunch
of fsl_booke things to say fsl_emb (Freescale Embedded Performance Monitors).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch to legacy_serial.c (1a7507c7da,
Reduce code duplication in legacy_serial, add UART parent types) changed
the semantics for opb ports from type = "opb" || compatible = "ibm,opb"
to type = "opb" && compatible = "ibm,opb".
The result is serial ports on our QS21s (Cell blades) don't get found,
and for some reason the machine doesn't boot at all - possibly it's
panicking due to lack of a console?
The fix is to add two entries to the of_device_id table, one that looks
for type = "opb" and the other compatible = "ibm,opb".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This ensures that the syscall and the (fast) vdso versions of
clock_getres() will return the same resolution.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x3017c): Section mismatch in reference from the function .vio_create_viodasd() to the function .devinit.text:.vio_register_device_node()
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously, during initialization of the IOMMU tables, the last entry
at each 4GB boundary is marked as used since there are many adapters
which cannot handle DMAing across any 4GB boundary.
The IOMMU doesn't allocate a memory area spanning LLD's segment
boundary anymore. The segment boundary of devices are set to 4GB by
default. So we can remove 4GB boundary protection now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts PPC's IOMMU to use the IOMMU helper functions. The IOMMU
doesn't allocate a memory area spanning LLD's segment boundary anymore.
iseries_hv_alloc and iseries_hv_map don't have proper device
struct. 4GB boundary is used for them.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
PPC: Fix powerpc vio_find_name to not use devices_subsys
Driver core: add bus_find_device_by_name function
Module: check to see if we have a built in module with the same name
x86: fix runtime error in arch/x86/kernel/cpu/mcheck/mce_amd_64.c
Driver core: Fix up build when CONFIG_BLOCK=N
This removes the handling for PTRACE_CONT et al from the powerpc
ptrace code, so it uses the new generic code via ptrace_request.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This defines the new standard arch_has_single_step macro. It makes the
existing set_single_step and clear_single_step entry points global, and
renames them to the new standard names user_enable_single_step and
user_disable_single_step, respectively.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the deprecated __attribute_used__.
[Introduce __section in a few places to silence checkpatch /sam]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
All current 85xx/e500 implementations only have two TLB
arrays. We are wasting cycles by invalidating TLB2 and TLB3.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The legacy_serial was treating each UART parent in a separate code block.
Rather than continue this trend for the new parent IDs, this condenses
all (soc, tsi, opb, plus two more new types) into one of_device_id array.
The new types are wrs,epld-localbus for the Wind River sbc8560, and a
more generic "simple-bus" as requested by Scott Wood.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes vio_find_name() in arch/powerpc/kernel/vio.c, which is
currently broken because it tries to use devices_subsys. That is bad
for two reasons: (1) it's doing (or trying to do) a scan of all
devices when it should only be scanning those on the vio bus, and
(2) devices_subsys was an internal symbol of the device system code
which was never meant for external use and has now gone away, and
thus the kernel fails to compile on pSeries.
The new version uses bus_find_device_by_name() on the vio bus
(vio_bus_type).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prune back Efika fixups to only include changes that are actually required
to get a working system. Most of the drivers can accept the compatible
properties, even if they don't match the what is recommented in the generic
names recommended practice document.
This patch also adds extra checks so that fixups are not performed blindly.
Instead, the code first verifies that the device tree is faulty before
making any changes. This way, if the Efika firmware is updated to fix
these issues, then the fixups will no longer get applied.
At this point; here is the list of fixups needed for the efika:
1. If the device_type property on the root node is 'chrp', then Linux won't
boot. Change device_type to 'efika' to avoid this condition
2. Add full interrupt list to the bestcomm node. In actual fact, the
bestcomm interrupts property is technically correct, it just doesn't
expose the same granularity as the device driver expects. All other
5200 device trees provide a separate irq number for each bestcomm
channel. Rather than hack the driver, it's simpler to fix it up
3. /builtin/sound node is missing an interrupts property
4. /builtin/ethernet node is missing a phy-handle property and the
device driver doesn't know what to do without one.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds the 440EP revision C PVR to the CPU table. The chip has an
FPU on it, so we also match the logical PVR
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds the 405EXr to the powerpc cuptable. Basically the 405EXr
is a 405EX with only one EMAC and only one PCIe interface.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since commit c80d9133e9 (Make direct DMA use
node local allocations) went in this comment makes no sense.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We no longer need the global dma_direct_offset, update the comment to
reflect the new reality.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that all platforms using dma_direct_offset setup the
archdata.dma_data correctly, we can change the dma_direct_ops to
retrieve the offset from the dma_data, rather than directly from the
global.
While we're here, change the way the offset is used - instead of
or'ing it into the value, add it. This should have no effect on
current implementations where the offset is far larger than memory,
however in future we may want to use smaller offsets.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We must always hookup the pci_bus resource 0 to the PHB io_resource
even if the latter is empty (the bus has no IO support). Otherwise,
some other code will end up hooking it up to something bogus and the
resource tree will end up being broken.
This fixes boot on QS20 Cell blades where the IDE driver failed to
allocate the IO resources due to breakage of the resource tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds hooks into the default_machine_crash_shutdown so drivers can
register a function to be run in the first kernel before we hand off
to the second kernel. This should only be used in exceptional
circumstances, like where the device can't be reset in the second
kernel alone (as is the case with eHEA). To emphasize this, the
number of handles allowed to be registered is currently #def to 1.
This uses the setjmp/longjmp code around the call out to the
registered hooks, so any bogus exceptions we encounter will hopefully
be recoverable.
Tested with bogus data and instruction exceptions.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the setjmp/longjmp code used by xmon, generically available
to other code. It also removes the requirement for debugger hooks to
be only called on 0x300 (data storage) exception.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Export copy_page() on 32-bit powerpc; unionfs needs it.
Unionfs already builds as a module on 64bit powerpc, so the export is
placed within an existing CONFIG_PPC32 #ifdef.
Signed-off-by: Joseph Fannin <jfannin@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
smp_send_stop() will send an IPI to all other cpus to shut them down.
However, for the case of xmon-based reboots (as well as potentially some
panics), the other cpus are (or might be) spinning with interrupts off,
and won't take the IPI.
Current code will drop us into the debugger when the IPI fails, which
means we're in an infinite loop that we can't get out of without an
external reset of some sort.
Instead, make the smp_send_stop() IPI call path just print the warning
about being unable to send IPIs, but make it return so the rest of the
shutdown sequence can continue. It's not perfect, but the lesser of
two evils.
Also move the call_lock handling outside of smp_call_function_map so we
can avoid deadlocks in smp_send_stop().
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
smp_call_function_map should be static, and for consistency prepend it
with __ like other local helper functions in the same file.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Do just enough to move the RapidIO support code for 85xx over from arch/ppc
into arch/powerpc and make it still build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The e500 MMU init code previously assumed KERNELBASE always equaled
PAGE_OFFSET and PHYSICAL_START was 0. This is useful for kdump
support as well as asymetric multicore.
For the initial kdump support the secondary kernel will run at 32M
but need access to all of memory so we bump the initial TLB up to
64M. This also matches with the forth coming ePAPR spec.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For transparent P2P bridges the first 3 resources may get set from based on
BAR registers and need to get fixed up. Where as the remainder come from the
parent bus and have already been fixed up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The fixup code that handles the case for PowerMac's that leave bridge
windows open over an inaccessible region should only be applied to
memory resources (IORESOURCE_MEM). If not we can get it trying to fixup
IORESOURCE_IO on some systems since the other conditions that are used to
detect the case can easily match for IORESOURCE_IO.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Using 64k pages on 64-bit PowerPC systems makes life difficult for
emulators that are trying to emulate an ISA, such as x86, which use a
smaller page size, since the emulator can no longer use the MMU and
the normal system calls for controlling page protections. Of course,
the emulator can emulate the MMU by checking and possibly remapping
the address for each memory access in software, but that is pretty
slow.
This provides a facility for such programs to control the access
permissions on individual 4k sub-pages of 64k pages. The idea is
that the emulator supplies an array of protection masks to apply to a
specified range of virtual addresses. These masks are applied at the
level where hardware PTEs are inserted into the hardware page table
based on the Linux PTEs, so the Linux PTEs are not affected. Note
that this new mechanism does not allow any access that would otherwise
be prohibited; it can only prohibit accesses that would otherwise be
allowed. This new facility is only available on 64-bit PowerPC and
only when the kernel is configured for 64k pages.
The masks are supplied using a new subpage_prot system call, which
takes a starting virtual address and length, and a pointer to an array
of protection masks in memory. The array has a 32-bit word per 64k
page to be protected; each 32-bit word consists of 16 2-bit fields,
for which 0 allows any access (that is otherwise allowed), 1 prevents
write accesses, and 2 or 3 prevent any access.
Implicit in this is that the regions of the address space that are
protected are switched to use 4k hardware pages rather than 64k
hardware pages (on machines with hardware 64k page support). In fact
the whole process is switched to use 4k hardware pages when the
subpage_prot system call is used, but this could be improved in future
to switch only the affected segments.
The subpage protection bits are stored in a 3 level tree akin to the
page table tree. The top level of this tree is stored in a structure
that is appended to the top level of the page table tree, i.e., the
pgd array. Since it will often only be 32-bit addresses (below 4GB)
that are protected, the pointers to the first four bottom level pages
are also stored in this structure (each bottom level page contains the
protection bits for 1GB of address space), so the protection bits for
addresses below 4GB can be accessed with one fewer loads than those
for higher addresses.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Also check that __NR_syscalls has been updated appropriately.
Hopefully this will catch any out of order additions to the
table in the future.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
xlate_iomm_address() really wants the ds_addr to pass to the HV, so store
that value (instead of the BAR number) when we allocate the device bars.
This is not a fast path, so we can look up the device_node property
there instead of using the bussubno field of the pci_dn.
The other user of iseries_ds_addr() was already scanning the device tree,
so looking up a property will not slow it down any more.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Similar to of_find_compatible_node(), of_find_matching_node() and
for_each_matching_node() allow you to iterate over the device tree
looking for specific nodes, except that they take of_device_id
tables instead of strings.
This also moves of_match_node() from driver/of/device.c to
driver/of/base.c to colocate it with the of_find_matching_node which
depends on it.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 5d2efba64b changed our iommu code
so that it always uses an iommu page size of 4kB. That means with our
current code, drivers may do a dma_map_sg() of a 64kB page and obtain
a dma_addr_t that is only 4k aligned.
This works fine in most cases except for some infiniband HW it seems,
where they tell the HW about the page size and it ignores the low bits
of the DMA address.
This works around it by making our IOMMU code enforce a PAGE_SIZE alignment
for mappings of objects that are page aligned in the first place and whose
size is larger or equal to a page.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new network driver fec_mpc52xx will not work on efika because the
firmware does not provide all required properties.
http://www.powerdeveloper.org/asset/by-id/46 has a Forth script to
create more properties. But only the phy stuff is required to get a
working network.
This should go into the kernel because its appearently
impossible to boot the script via tftp and then load the real boot
binary (yaboot or zimage).
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This reverts commit 553aa7659b at Ben H's
request, because it confused IORESOURCE_* flags with command register
bits.
Requested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The e200 and e500 platforms are separated in various parts of the kernel with
ifdefs, most notably reg_booke.h and traps.c. The new machine_check rework
requires them to be similarly separated in cputable.c to avoid compile errors.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Renaming the CPU nodes with generic names put the CPU model in
the "model" property and thus broke the PowerPC 440EP(x)/440GR(x)
identical PVR workaround. The updates it to use the new model property
for CPU identification.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The mechanism to do the setup for 440A cores changed recently. This fixes
the 440grx setup function to call __fixup_440A_mcheck.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds some basic real mode based early udbg support for 40x
in order to debug things more easily
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a cputable function pointer for the CPU-side machine
check handling. The semantic is still the same as the old one,
the one in ppc_md. overrides the one in cputable, though
ultimately we'll want to change that so the CPU gets first.
This removes CONFIG_440A which was a problem for multiplatform
kernels and instead fixes up the IVOR at runtime from a setup_cpu
function. The "A" version of the machine check also tweaks the
regs->trap value to differenciate the 2 versions at the C level.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This will allow us to declare const all the statically declared arrrays
of these.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit PCI code tests if "bus" is non-NULL after calling
pci_scan_bus_parented() in one place but not another before
dereferencing it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These hooks ensure that a decrementer interrupt is not pending when
suspending; otherwise, problems may occur on 6xx/7xx/7xxx-based
systems (except for powermacs, which use a separate suspend path).
For example, with deep sleep on the 831x, a pending decrementer will
cause a system freeze because the SoC thinks the decrementer interrupt
would have woken the system, but the core must have interrupts
disabled due to the setup required for deep sleep.
Changed via-pmu.c to use the new ppc_md hooks, and made the arch_*
functions call the generic_* functions unconditionally. -- paulus
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When a module has relocation sections with tens of thousands of
entries, counting the distinct/unique entries only (i.e. no
duplicates) at load time can take tens of seconds and up to minutes.
The sore point is the count_relocs() function which is called as part
of the architecture specific module loading processing path:
-> load_module() generic
-> module_frob_arch_sections() arch specific
-> get_plt_size() 32-bit
-> get_stubs_size() 64-bit
-> count_relocs()
Here count_relocs is being called to find out how many distinct
targets of R_PPC_REL24 relocations there are, since each distinct
target needs a PLT entry or a stub created for it.
The previous counting algorithm has O(n^2) complexity. Basically two
solutions were proposed on the e-mail list: a hash based approach and
a sort based approach.
The hash based approach is the fastest (O(n)) but the has it needs
additional memory and for certain corner cases it could take lots of
memory due to the degeneration of the hash. One such proposal was
submitted here:
http://ozlabs.org/pipermail/linuxppc-dev/2007-June/037641.html
The sort based approach is slower (O(n * log n + n)) but if the
sorting is done "in place" it doesn't need additional memory.
This has O(n + n * log n) complexity with no additional memory
requirements.
This commit implements the in-place sort option.
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Lucas Woods <woodzy@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We were using -mno-minimal-toc on everything in arch/powerpc/kernel,
which means that all the functions in there were putting all their
TOC entries in the top-level TOC, and it was overflowing on an
allyesconfig build. For various reasons, prom_init.c does need
-mno-minimal-toc, but the other .c files in there can use sub-TOCs
quite happily. This change is sufficient for now to stop the TOC
overflowing; other directories under arch/powerpc also use
-mno-minimal-toc and could also be changed later if necessary.
Lmbench runs with and without this patch showed no significant speed
differences.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PCI IRQ code has a fallback when the device-tree parsing fails, that
tries to map the interrupt indicated by PCI_INTERRUPT_LINE if the firmware
set something in there. This is a bit fragile but has proven useful in some
cases so far. However, it's causing us to incorrectly try to map interrupt 0
on various setups, so let's prevent that case, as none of the cases where
the fallback is legit should have an IRQ 0.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch changes the PowerPC PCI code to disable IO and/or Memory
decoding on a PCI device when a resource of that type failed to be
allocated. This is done to avoid having unallocated dangling BARs
enabled that might try to decode on top of other devices.
If a proper resource is assigned later on, then pci_enable_device()
will take care of re-enabling decoding.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apple firmware has a strange way to "close" bridge resources by setting
them to some bogus values that overlap RAM (strangely, I haven't seen it
conflicting with DMA so far...). This explicitely closes them to avoid
problems. Previously, they would be closed as a consequence of failing
to be allocated, but this makes it more explicit, and thus the log
message is more explicit too.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our implementation of pcibios_enable_device() has a couple of problems.
One is that it should not check IORESOURCE_UNSET, as this might be
left dangling after resource assignment (shouldn't but there are
bugs), but instead, we make it check resource->parent which should
be a reliable indication that the resource has been successfully
claimed (it's in the resource tree).
Then, we also need to skip ROM resources that haven't been enabled
as x86 does.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merge the two implementations, based on the previously
fixed up 32 bits one. The pcibios_enable_device_hook in ppc_md
is now available for ppc64 use. Also remove the new unused
"initial" parameter from it and fixup users.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our implementation of pcibios_enable_device() incorrectly ignores
the mask argument and always checks that all resources have been
allocated, which isn't the right thing to do anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The way iSeries manages PCI IO and Memory resources is a bit strange
and is based on overriding the content of those resources with home
cooked ones afterward.
This changes it a bit to better integrate with the new resource handling
so that the "virtual" tokens that iSeries replaces resources with are
done from the proper per-device fixup hook, and bridge resources are
set to enclose that token space. This fixes various things such as
the output of /proc/iomem & ioports, among others. This also fixes up
various boot messages as well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PCI code now uses the generic code for assigning unassigned
resources and an algorithm similar to x86 for claiming existing ones.
This works far better than the 64 bits code which basically can only
claim existing ones (pci_probe_only=1) or would fall apart completely.
This merges them so that the new 32 bits implementation is used for both.
64 bits now gets the new PCI flags for controlling the behaviour, though
the old pci_probe_only global is still there for now to be cleared if you
want to.
I kept a pcibios_claim_one_bus() function mostly based on the old 64
bits code for use by the DLPAR hotplug. This will have to be cleaned
up, thought I hope it will work in the meantime.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PCI code in 32 and 64 bits fixes up resources differently.
32 bits uses a header quirk plus handles bridges in pcibios_fixup_bus()
while 64 bits does things in various places depending on whether you
are using OF probing, using PCI hotplug, etc...
This merges those by basically using the 32 bits approach for both,
with various tweaks to make 64 bits work with the new approach.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges the PowerPC 32 and 64 bits version of pcibios_resource_to_bus
and pcibios_bus_to_resource().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds flags the platforms can use to enable domain numbers
in /proc/bus/pci.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PCI code carries an old hack that was only useful for G5
machines. Nowdays, the 32 bits kernel doesn't support any of those
machines anymore so the hack is basically never used, so remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds to the 32 bits PCI code some flags, replacing the old
pci_assign_all_busses global, that allow us to control various
aspects of the PCI probing, such as whether to re-assign all
resources or not, or to not try to assign anything at all.
This also adds the flag x86 already has to avoid ISA alignment
on bridges that don't have ISA forwarding enabled (no legacy
devices on the top level bus) and sets it for PowerMacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PowerPC PCI code has a hack for use by some PowerMacs
to try to re-open PCI<->PCI bridge IO resources that were closed
by the firmware. This is no longer necessary as the generic code
will now do that for us.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the 32 bits PowerPC PCI code use the generic code to assign
resources to devices that had unassigned or conflicting resources.
This allow us to remove the local implementation that was incomplete and
could not assign for example a PCI<->PCI bridge from scratch, which is
needed on various embedded platforms.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There's a stale & bogus piece of code in 32 bits PCI code that
complains about ISA related alignment issues. Just remove it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerPC currently doesn't implement pci_set_dma_mask(), which means drivers
calling it will get the generic version in drivers/pci/pci.c.
The powerpc dma mapping ops include a dma_set_mask() hook, which luckily is
not implemented by anyone - so there is no bug in the fact that the hook
is currently never called.
However in future we'll add implementation(s) of dma_set_mask(), and so we
need pci_set_dma_mask() to call the hook.
To save adding a hook to the dma mapping ops, pci-set_consistent_dma_mask()
simply calls the dma_set_mask() hook and then copies the new mask into
dev.coherenet_dma_mask.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have multiple calls to has_feature being inlined, but gcc can't
be sure that the store via get_paca() doesn't alias the path to
cur_cpu_spec->feature.
Reorder to put the calls to read_purr and read_spurr adjacent to each
other. To add a sense of consistency, reorder the remaining lines to
perform parallel steps on purr and scaled purr of each line instead of
calculating and then using one value before going on to the next.
In addition, we can tell gcc that no SPURR means no PURR. The test is
completely hidden in the PURR case, and in the !PURR case the second test
is eliminated resulting in the simple register copy in the out-of-line
branch.
Further, gcc sees get_paca()->system_time referenced several times and
allocates a register to address it (shadowing r13) instead of caching its
value. Reading into a local varable saves the shadow of r13 and removes
a potentially duplicate load (between the nested if and its parent).
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If CPU_FTR_PURR is not set, we will never set cpu_purr_data->initialized.
Checking via __get_cpu_var on 64 bit avoids one dependent load compared
to cpu_has_feature in the not-present case, and is always required when
it is present. The code is under CONFIG_VIRT_CPU_ACCOUNTING so 32 bit
will not be affected.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
timer_interrupt() was calculating per_cpu_offset several times, having to
start from the toc because of potential aliasing issues.
Placing both decrementer per_cpu varables in a struct and calculating
the address once with __get_cpu_var results in better code on both 32
and 64 bit.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use __get_cpu_var(x) instead of per_cpu(x, smp_processor_id()), as it
is optimized on ppc64 to access the current cpu's per-cpu offset directly;
it's local_paca.offset instead of TOC->paca[local_paca->processor_id].offset.
This is the trivial portion, two functions with one use each.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
as its only called from time_init, which is __init.
Also remove unneeded forward declaration.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove exports of __res and cpm_install_handler/cpm_free_handler. Remove
cpm_install_handler/cpm_free_handler from the commproc.h as well. Both
were used for ARCH=ppc and aren't defined for ARCH=powerpc.
CC arch/powerpc/kernel/ppc_ksyms.o
arch/powerpc/kernel/ppc_ksyms.c:180: error: '__res' undeclared here (not in a function)
arch/powerpc/kernel/ppc_ksyms.c:180: warning: type defaults to 'int' in declaration of '__res'
make[1]: *** [arch/powerpc/kernel/ppc_ksyms.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
LD .tmp_vmlinux1
arch/powerpc/kernel/built-in.o:(__ksymtab+0x198): undefined reference to `cpm_free_handler'
arch/powerpc/kernel/built-in.o:(__ksymtab+0x1a0): undefined reference to `cpm_install_handler'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
isel (Integer Select) is a new user space instruction in the
PowerISA 2.04 spec. Not all processors implement it so lets emulate
to ensure code built with isel will run everywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This makes the early debug option force the console loglevel
to the max. The early debug option is meant to catch messages very
early in the kernel boot process, in many cases, before the kernel
has a chance to parse the "debug" command line argument. Thus it
makes sense when CONFIG_PPC_EARLY_DEBUG is set, to force the console
log level to the max at boot time.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a variant of of_translate_address that uses the dma-ranges
property instead of "ranges", it's to be used by PCI code in parsing
the dma-ranges property.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes "volatile" from the MMIO pointer udbg_comport
in udbg_16550.c driver, it's useless and makes checkpatch.pl
complain when adding things to this file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32 bits PCI code will display a rather scary error message
PCI: Cannot allocate resource region N of device XXX
at boot when the existing setup of a device as left by the
firmware doesn't match the kernel needs and the device needs
to be moved. This is often not an error at all, as the kernel
will generally easily reallocate the device elsewhere.
This changes the message to something less scary and lowers
its level from error to warning.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The 32-bit powerpc resource fixup code uses unsigned longs to do the
offsetting of resources which overflows on platforms such as 4xx where
resources can be 64 bits.
This fixes it by using resource_size_t instead.
However, the IO stuff does rely on some 32 bits arithmetic, so we hack
by cropping the result of the fixups for IO resources with a 32 bits
mask.
This isn't the prettiest but should work for now until we change the
32 bits PCI code to do IO mappings like 64 bits does, within a reserved
are of the kernel address space.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This merges the 32-bit and 64-bit implementations of
pci_process_bridge_OF_ranges(). The new function is cleaner than both
the old ones, and supports 64 bits ranges on ppc32 which is necessary
for the 4xx port.
It also adds some better (hopefully) output to the kernel log which
should help diagnose problems and makes better use of existing OF
parsing helpers (avoiding a few bugs of both implementations along
the way).
There are still a few unfortunate ifdef's but there is no way around
these for now at least not until some other bits of the PCI code are
made common.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This defines isa_mem_base on both 32 and 64 bits (it used to be 32 bits
only). This avoids a few ifdef's in later patches and potentially can
allow support for VGA text mode on 64 bits powerpc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently we hardwire the number of SLBs to 64, but PAPR says we
should use the ibm,slb-size property to obtain the number of SLB
entries. This uses this property instead of assuming 64. If no
property is found, we assume 64 entries as before.
This soft patches the SLB handler, so it shouldn't change performance
at all.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
