If set_fmt callback is called with format->width or format->height set to
zero and HACTIVE_CNT or VACTIVE_CNT bits (respectively) in chip are zero
we will divide by zero later in this callback when we try to calculate
HSC or VSC values.
Fix this by explicitly rejecting these values.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A 0b1100 value in 4 LSBs of "General Status 1" register (AFD_FMT_STAT) has
known meaning for CX2584x-series chips - it means that a SECAM signal is
currently detected by the chip.
Use this opportunity to also fix wrong binary values that were present
as comments attached to some entries in an array where
chip register -> V4L2 standard mappings are stored.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As we're now using SPDX identifiers, on the several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.
As we're now using the short license, it doesn't make sense to
keep the original license text.
Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As of_node_full_name() now returns only the basename, the endpoint
information printed became useless:
adv748x 4-0070: Endpoint endpoint on port 7
adv748x 4-0070: Endpoint endpoint on port 8
adv748x 4-0070: Endpoint endpoint on port 10
adv748x 4-0070: Endpoint endpoint on port 11
Restore the old behavior by using "%pOF" instead:
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@7/endpoint on port 7
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@8/endpoint on port 8
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@10/endpoint on port 10
adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@11/endpoint on port 11
Fixes: a7e4cfb0a7 ("of/fdt: only store the device node basename in full_name")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A 'return' was missing when detecting Arbitration Lost and
calling transmit_done. With the return transmit_done could be
called a second time, confusing the CEC framework. Luckily
the Arbitration Lost condition is very rare.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since i2c_unregister_device() became NULL-aware we may remove duplicate checks.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The current implementation has to search the list of controls for the
pixel rate control, each time it is set. This can be optimised easily
by storing the ctrl pointer in the CSI/TX object, and referencing that
directly.
While at it, fix up a missing blank line also highlighted in review
comments.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mt9v032_power_on() leaves clk enabled in case of errors,
but it is not expected by its callers.
There is a similar problem in mt9v032_registered().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov7670 has the test pattern generator features. This makes use of
it through V4L2_CID_TEST_PATTERN control.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The sub-device for ov7670 is registered by v4l2_async_register_subdev().
So it should be unregistered by v4l2_async_unregister_subdev() instead of
v4l2_device_unregister_subdev().
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the missing MAINTAINERS entry for imx274, fix error handling in driver
probe and unregister the correct control handler in driver remove.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_async_register_subdev_sensor_common() is only provided when
CONFIG_V4L2_FWNODE is enabled, otherwise we get a link failure:
drivers/media/i2c/et8ek8/et8ek8_driver.o: In function `et8ek8_probe':
et8ek8_driver.c:(.text+0x884): undefined reference to `v4l2_async_register_subdev_sensor_common'
This adds a Kconfig 'select' statement like all the other users of
this interface have.
Fixes: d8932f38c1 ("media: et8ek8: Add support for flash and lens devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov13858 driver depends on the V4L2 fwnode, thus add that to Kconfig.
Fixes: 5fcf092e0c ("[media] ov13858: add support for OV13858 sensor")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several comments are wrongly tagged as kernel-doc, causing
those warnings:
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'irq'
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'data'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'solo_dev'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'ch'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'qp'
drivers/media/usb/pwc/pwc-dec23.c:652: warning: Cannot understand *
on line 652 - I thought it was a doc line
drivers/media/usb/dvb-usb/cinergyT2-fe.c:40: warning: No description found for parameter 'op'
drivers/media/usb/dvb-usb/friio-fe.c:301: warning: Cannot understand * (reg, val) commad list to initialize this module.
on line 301 - I thought it was a doc line
drivers/media/rc/streamzap.c:201: warning: No description found for parameter 'urb'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'intf'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'id'
drivers/media/rc/streamzap.c:464: warning: No description found for parameter 'interface'
drivers/media/i2c/ov5647.c:432: warning: Cannot understand * @short Subdev core operations registration
on line 432 - I thought it was a doc line
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'd'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'addr'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wlen'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rlen'
drivers/media/platform/vim2m.c:350: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/tua6100.c:34: warning: cannot understand function prototype: 'struct tua6100_priv '
drivers/media/platform/sti/hva/hva-h264.c:140: warning: cannot understand function prototype: 'struct hva_h264_stereo_video_sei '
drivers/media/platform/sti/hva/hva-h264.c:150: warning: Cannot understand * @frame_width: width in pixels of the buffer containing the input frame
on line 150 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:356: warning: Cannot understand * @ slice_size: slice size
on line 356 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:369: warning: Cannot understand * @ bitstream_size: bitstream size
on line 369 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:395: warning: Cannot understand * @seq_info: sequence information buffer
on line 395 - I thought it was a doc line
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fe'
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fw'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'n'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'd'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_i'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_f'
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:83: warning: cannot understand function prototype: 'struct ttusb '
drivers/media/platform/sh_veu.c:277: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/zl10036.c:33: warning: cannot understand function prototype: 'int zl10036_debug; '
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'frequency'
drivers/media/platform/rcar_fdp1.c:1139: warning: No description found for parameter 'priv'
drivers/media/platform/ti-vpe/vpe.c:933: warning: No description found for parameter 'priv'
drivers/media/usb/gspca/ov519.c:36: warning: No description found for parameter 'fmt'
drivers/media/usb/dvb-usb/dib0700_devices.c:3367: warning: No description found for parameter 'adap'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix this warning:
drivers/media/i2c/lm3560.c:69: warning: No description found for parameter 'dev'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are some struct fields that aren't documented, and some
consts whose comments start with /**, but they aren't kernel-doc
annotations. So, fix it:
drivers/media/i2c/tvp514x.c:127: warning: No description found for parameter 'hdl'
drivers/media/i2c/tvp514x.c:127: warning: No description found for parameter 'pad'
drivers/media/i2c/tvp514x.c:127: warning: No description found for parameter 'format'
drivers/media/i2c/tvp514x.c:127: warning: No description found for parameter 'int_seq'
drivers/media/i2c/tvp514x.c:219: warning: cannot understand function prototype: 'const struct v4l2_fmtdesc tvp514x_fmt_list[] = '
drivers/media/i2c/tvp514x.c:235: warning: cannot understand function prototype: 'const struct tvp514x_std_info tvp514x_std_list[] = '
drivers/media/i2c/tvp514x.c:941: warning: No description found for parameter 'fmt'
drivers/media/i2c/tvp514x.c:941: warning: Excess function parameter 'format' description in 'tvp514x_set_pad_format'
drivers/media/i2c/tvp514x.c:1208: warning: cannot understand function prototype: 'const struct i2c_device_id tvp514x_id[] = '
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
as warned:
drivers/media/i2c/s5k6aa.c:429: warning: No description found for parameter 's5k6aa'
drivers/media/i2c/s5k6aa.c:679: warning: No description found for parameter 's5k6aa'
drivers/media/i2c/s5k6aa.c:733: warning: No description found for parameter 's5k6aa'
drivers/media/i2c/s5k6aa.c:733: warning: No description found for parameter 'preset'
drivers/media/i2c/s5k6aa.c:787: warning: No description found for parameter 'sd'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/i2c/s5k6a3.c:68: warning: No description found for parameter 'clock'
drivers/media/i2c/s5k6a3.c:68: warning: No description found for parameter 'clock_frequency'
drivers/media/i2c/s5k6a3.c:68: warning: No description found for parameter 'power_count'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix those warnings:
drivers/media/i2c/m5mols/m5mols_capture.c:42: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_capture.c:42: warning: No description found for parameter 'addr_num'
drivers/media/i2c/m5mols/m5mols_capture.c:42: warning: No description found for parameter 'addr_den'
drivers/media/i2c/m5mols/m5mols_capture.c:42: warning: No description found for parameter 'val'
drivers/media/i2c/m5mols/m5mols_capture.c:60: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_controls.c:134: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_core.c:124: warning: No description found for parameter 'data'
drivers/media/i2c/m5mols/m5mols_core.c:124: warning: No description found for parameter 'length'
drivers/media/i2c/m5mols/m5mols_core.c:124: warning: Excess function parameter 'size' description in 'm5mols_swap_byte'
drivers/media/i2c/m5mols/m5mols_core.c:142: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:241: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:299: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:324: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:324: warning: No description found for parameter 'reg'
drivers/media/i2c/m5mols/m5mols_core.c:357: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:357: warning: No description found for parameter 'mode'
drivers/media/i2c/m5mols/m5mols_core.c:374: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_core.c:429: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:503: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:671: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_core.c:694: warning: No description found for parameter 'info'
drivers/media/i2c/m5mols/m5mols_core.c:798: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:853: warning: No description found for parameter 'sd'
drivers/media/i2c/m5mols/m5mols_core.c:853: warning: No description found for parameter 'on'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
The variable ret is being checked for failure however it is not being set
from the return status from the call to imx274_mode_regs. Currently ret is
alwayus zero and the check is redundant. Fix this by assigning it.
Detected by CoverityScan, CID#1460278 ("Logically dead code")
Fixes: 0985dd306f ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
These types devices aren't directly related to the sensor, but are
nevertheless handled by the smiapp driver due to the relationship of these
component to the main part of the camera module --- the sensor.
This does not yet address providing the user space with information on how
to associate the sensor or lens devices but the kernel now has the
necessary information to do that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The test_pattern_menu[] array has two valid items and a null terminated
item. So the control's maximum value which is passed to
v4l2_ctrl_new_std_menu_items() should be one. However,
'ARRAY_SIZE(test_pattern_menu) - 1' is actually passed and it's not
correct.
Fix it by removing unnecessary terminated entry and let the correct
control's maximum value be passed to v4l2_ctrl_new_std_menu_items().
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_i2c_subdev_init() sets V4L2_SUBDEV_FL_IS_I2C flag in the
subdev->flags. But this driver overwrites subdev->flags immediately after
calling v4l2_i2c_subdev_init(). So V4L2_SUBDEV_FL_IS_I2C is not set after
all.
This stops breaking subdev->flags and preserves V4L2_SUBDEV_FL_IS_I2C.
Side note: According to the comment in v4l2_device_unregister(), this is
problematic only if the device is platform bus device. Device tree or
ACPI based devices are not affected.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The TC358743 does not support more than 4 data lanes. Check that the
lane count is valid.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When I was supporting Rpi Camera Module on the ASUS Tinker board,
I found this driver have some issues with rockchip's mipi-csi driver.
It didn't place clock lane in LP-11 state before performing
D-PHY initialisation.
>From our experience, on some OV sensors,
LP-11 state is not achieved while BIT(5)-0x4800 is cleared.
So let's set BIT(5) and BIT(0) both while not streaming, in order to
coax the clock lane into LP-11 state.
0x4800 : MIPI CTRL 00
BIT(5) : clock lane gate enable
0: continuous
1: none-continuous
BIT(0) : manually set clock lane
0: Not used
1: used
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the ov7670_s_power function which is responsible for
manipulating the power dowm mode through the PWDN pin and the reset
operation through the RESET pin, and keep it powered at all times.
[sakari.ailus@linux.intel.com: set pwdn_gpio direction only once]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the get_fmt callback, also enable V4L2_SUBDEV_FL_HAS_DEVNODE flag
to make this subdev has device node.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the media entity pads initialization.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The imx274 is a Sony CMOS image sensor that has 1/2.5 image size.
It supports up to 3840x2160 (4K) 60fps, 1080p 120fps. The interface
is 4-lane MIPI CSI-2 running at 1.44Gbps each.
This driver has been tested on Xilinx ZCU102 platform with a Leopard
LI-IMX274MIPI-FMC camera board.
Support for the following features:
-Resolutions: 3840x2160, 1920x1080, 1280x720
-Frame rate: 3840x2160 : 5 – 60fps
1920x1080 : 5 – 120fps
1280x720 : 5 – 120fps
-Exposure time: 16 – (frame interval) micro-seconds
-Gain: 1x - 180x
-VFLIP: enable/disabledrivers/media/i2c/imx274.c
-Test pattern: 12 test patterns
Signed-off-by: Leon Luo <leonl@leopardimaging.com>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TC358743 is an HDMI to MIPI CSI2-2 bridge.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We can remove the check for if "state->cec_adap" is NULL. The
cec_allocate_adapter() function never returns NULL and also we verified
that "state->cec_adap" is an error pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It should be "LP-11".
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of relying on a mix of runtime PM and the s_power() callback, drop
the s_power() callback altogether and use runtime PM solely.
As device access is required during device power-on and power-off
sequences, runtime PM alone cannot tell whether the device is available.
Thus the "active" field is introduced in struct smiapp_sensor to tell
whether it is safe to write to the device.
Consequently there is no need to power on the device whenever a file
handle is open. This functionality is removed as well. The user may still
control the device power management through sysfs. Autosuspend remains
enabled, with 1 s delay.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use unlocked __v4l2_ctrl_handler_setup() in order to make the
control setup atomic.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The clock control is not explicitly controlled by the driver in two cases:
ACPI based systems and when the clock is part of the power sequence of the
camera module.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Obtain the clock rate from the clock framework if it's not available
through DT. The assumption is that the parent device (camera module)
defines the rate as clock control is a part of the power on and power off
sequences --- which are camera module specific.
Also use the clock rate from DT if no clock is provided.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The external clock frequency was set by the driver but the obtained
frequency was never verified. Do that.
Being able to obtain the exact frequency is important as the value is used
for PLL calculations which may result in frequencies that violate the PLL
tree limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The error handling code in smiapp_power_on() returned in case of a failed
I2C write instead of cleaning up the mess. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ov13858 contained a 64-bit division. Use do_div() for calculating it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, with crop (0, 0), (4255, 3167), VTS < 0xC9E was resulting in
blank frames sometimes. This appeared as video flickering. But we need VTS
< 0xC9E to get ~30fps.
Omni Vision recommends to use crop (0,8), (4255, 3159) for 4224x3136. With
this crop, VTS 0xC8E is supported and yields ~30fps.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calculate pixel-rate at run time instead of compile time.
Instead of using hardcoded pixels-per-line, extract it from current sensor
mode.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't populate the array reset_seq on the stack, instead make it
static. Makes the object code smaller by over 50 bytes:
Before:
text data bss dec hex filename
11737 6000 64 17801 4589 drivers/media/i2c/ov2640.o
After:
text data bss dec hex filename
11582 6096 64 17742 454e drivers/media/i2c/ov2640.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the specification of a data structure by pointer dereferences
as the parameter for the operator "sizeof" to make size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensource.com: merged similar patches]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Omit extra messages for memory allocation failures.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensource.com: merged similar patches]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, the sensor was not streaming after resume from suspend,
i.e. on S0->S3->S0 transition. Due to this, camera app preview appeared
as stuck.
Now, handle streaming state correctly in case of suspend-resume.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Current v4l2 focus ctrl step value of 16, limits the minimum granularity
of focus positions to 16. Setting this value as 1, enables more accurate
focus positions.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
devm_clk_get() may return different error codes other than -EPROBE_DEFER,
so it is better to return the real error code instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
v4l2_clk_get() may return different error codes other than -EPROBE_DEFER,
so it is better to return the real error code instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, images were relatively darker due to non-optimal
settings for black target level and bias.
Now, use recommended settings for black target level and output bias
as default values. The same default settings apply to all the resolutions.
Given these recommeneded settings do not change dynamically, add these to
existing mode register settings.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This converts to use setup_timer() to set callback and data, though it
doesn't look like this would have worked with timer checking enabled
since no init_timer() was ever called before.
Cc: Mats Randgaard <matrandg@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video standard was not mapped to the corresponding value of the
internal video standard in adv748x_afe_querystd, causing the wrong
video standard to be selected.
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
[Kieran: Obtain the std from the afe->curr_norm]
Signed-off-by: Simon Yuan <simon.yuan@navico.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rc scancode drivers without change_protocol should have all
protocols enabled at all time. This was only true for cec and
ir-kbd-i2c.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't populate the arrays res_x and resy_y on the stack, instead make them
static const. Makes the object code smaller by over 160 bytes:
Before:
text data bss dec hex filename
10509 2800 64 13373 343d ov9640.o
After:
text data bss dec hex filename
10184 2960 64 13208 3398 ov9640.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the array syds on the stack, instead make it static const.
Makes the object code smaller by over 280 bytes:
Before:
text data bss dec hex filename
81451 12784 704 94939 172db cx25840-core.o
text data bss dec hex filename
81070 12880 704 94654 171be cx25840-core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written !…
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensoure.com: merge similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensource.com: fold several similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add CEC support for the tc358743 HDMI-CSI bridge.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When devm_clk_get() fails we should return the real error code
instead of always returning -ENODEV.
This allows defer probe to happen in the case the clock provider has
not been enabled by the time max2175 driver gets probed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, and the driver is only exporting the OF ID
table entries as module aliases.
So if the driver is built as module, autoload won't work since udev/kmod
won't be able to match the registered OF device with its driver module.
Before this patch:
$ modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
After this patch:
modinfo drivers/media/i2c/adv748x/adv748x.ko | grep alias
alias: of:N*T*Cadi,adv7482C*
alias: of:N*T*Cadi,adv7482
alias: of:N*T*Cadi,adv7481C*
alias: of:N*T*Cadi,adv7481
alias: i2c:adv7482
alias: i2c:adv7481
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check memory allocation failure and return -ENOMEM in such a case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ACPI match table is empty. Remove it.
Also convert the drive to use probe_new callback in struct i2c_driver.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, vblank range given to user was too big, falling outside
of permissible range for a given resolution. Sometimes, too low vblank
resulted in errors.
Now, limit vblank to only permissible range for a given resolution.
This change limits lower-bounds of vblank, doesn't affect upper bounds.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, vblank range given to user was too big, falling outside
of permissible range for a given resolution. Sometimes, too low vblank
resulted in errors.
Now, limit vblank to only permissible range for a given resolution.
This change limits lower-bounds of vblank, doesn't affect upper bounds.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The et8ek8 driver combines I²C register writes to a single array that it
passes to i2c_transfer(). The maximum number of writes is 48 at once,
decrease it to 8 and make more transfers if needed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_subdev_ops structure is only passed as the third argument
of v4l2_i2c_subdev_init, which is const, so the v4l2_subdev_ops
structure can be const as well. The other structures are only
stored in the v4l2_subdev_ops structure, all the fields of which are
const, so these structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The v4l2_subdev_ops structure is only passed as the third argument of
v4l2_i2c_subdev_init, which is const, so the v4l2_subdev_ops structure
can be const as well. The other structures are only stored in the
v4l2_subdev_ops structure, all the fields of which are const, so these
structures can also be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, pixel-rate/(pixels-per-line * lines-per-frame) was
yielding incorrect frame timing for the user.
OV sensor is using internal timing and this requires
conversion (internal timing -> PPL) for correct HBLANK calculation.
Now, change pixels-per-line domain from internal sensor clock to
pixels domain. Set HBLANK read-only because fixed PPL is used for all
resolutions. And, use more accurate link-frequency 422.4MHz instead of
rounding down to 420MHz.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The structure vs6624_default_fmt is only copied into another
structure field, so it can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, possible digital gains were just 1x, 2x and 4x. These
coarse gains were not sufficient in fine-tuning the image capture.
Now, digital gain range is [0, 16x] with each step 1/1024, default 1x.
This is achieved through OV13858 MWB R/G/B gain controls.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously both link-frequency and pixel-rate reported by
the sensor was incorrect, resulting in incorrect FPS.
Report link-frequency in Hz rather than link data rate in bps.
Calculate pixel-rate from link-frequency.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously, initial exposure max was set incorrectly to (0x7fff - 8).
Now, limit exposure max to current resolution (VTS - 8).
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On format change, sometimes, sensor was streaming at a much higher
FPS than the default. This was resulting in various problems like
frame drops/corruption.
Upon format change, set default vblank as current vblank. This will
ensure that sensor will start streaming at default fps.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These can only be accessed with CAP_SYS_ADMIN so it's not a critical
security issue. The problem is that "page" is controlled by the user in
the ioctl(). The test to see if the bit is set in state->info->page_mask
is not sufficient because "page" can be very high and shift wrap around
to a bit which is set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the new CEC_CAP_DEFAULTS define in the adv, vivid, pulse8 and
rainshadow CEC drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The new ov5670 driver fails to build when VIDEO_V4L2_SUBDEV_API
or MEDIA_CONTROLLER are disabled:
drivers/media/i2c/ov5670.c: In function 'ov5670_open':
drivers/media/i2c/ov5670.c:1917:5: error: implicit declaration of function 'v4l2_subdev_get_try_format'; did you mean 'v4l2_subdev_notify_event'? [-Werror=implicit-function-declaration]
v4l2_subdev_get_try_format(sd, fh->pad, 0);
^~~~~~~~~~~~~~~~~~~~~~~~~~
v4l2_subdev_notify_event
drivers/media/i2c/ov5670.c:1917:38: error: 'struct v4l2_subdev_fh' has no member named 'pad'
v4l2_subdev_get_try_format(sd, fh->pad, 0);
^~
drivers/media/i2c/ov5670.c: In function 'ov5670_do_get_pad_format':
drivers/media/i2c/ov5670.c:2198:17: error: invalid type argument of unary '*' (have 'int')
fmt->format = *v4l2_subdev_get_try_format(&ov5670->sd, cfg,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
fmt->pad);
~~~~~~~~~
drivers/media/i2c/ov5670.c: At top level:
drivers/media/i2c/ov5670.c:2444:19: error: 'v4l2_subdev_link_validate' undeclared here (not in a function); did you mean 'v4l2_subdev_init'?
.link_validate = v4l2_subdev_link_validate,
^~~~~~~~~~~~~~~~~~~~~~~~~
v4l2_subdev_init
drivers/media/i2c/ov5670.c: In function 'ov5670_probe':
drivers/media/i2c/ov5670.c:2492:12: error: 'struct v4l2_subdev' has no member named 'entity'
This adds both to the Kconfig entry.
Fixes: 5de35c9b8d ("media: i2c: Add Omnivision OV5670 5M sensor support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix missing mutex_destroy() when probe fails and
when driver is removed.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When devm_clk_get() fails the real error code should be propagated,
instead of always returning -EPROBE_DEFER.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove unnecessary static on local variable rtype. Such variable
is initialized before being used, on every execution path throughout
the function. The static has no benefit and, removing it reduces
the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
there is a significant difference in the bss segment. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
27765 5656 320 33741 83cd drivers/media/i2c/s5k5baf.o
after:
text data bss dec hex filename
27733 5600 256 33589 8335 drivers/media/i2c/s5k5baf.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/i2c/adv748x/adv748x-csi2.c: In function 'adv748x_csi2_init_controls':
drivers/media/i2c/adv748x/adv748x-csi2.c:251:20: warning: variable 'ctrl' set but not used [-Wunused-but-set-variable]
struct v4l2_ctrl *ctrl;
^~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provide support for the ADV7481 and ADV7482.
The driver is modelled with 4 subdevices to allow simultaneous streaming
from the AFE (Analog front end) and HDMI inputs though two CSI TX
entities.
The HDMI entity is linked to the TXA CSI bus, whilst the AFE is linked
to the TXB CSI bus.
The driver is based on a prototype by Koji Matsuoka in the Renesas BSP,
and an earlier rework by Niklas Söderlund.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Provides single source pad with up to 2592x1944 pixels at 10-bit raw
bayer format over MIPI CSI2 two lanes at 840Mbps/lane.
The driver supports following features:
- up to 30fps at 5M pixels
- manual exposure
- digital/analog gain
- V-blank/H-blank
- test pattern
- media controller
- runtime pm
[mchehab@s-opensource.com: fix a trivial merge conflict at Makefile]
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate const arrays on the stack but instead make them static.
Makes the object code smaller and saves nearly 550 bytes.
Before:
text data bss dec hex filename
3638 752 0 4390 1126 smiapp-quirk.o
After:
text data bss dec hex filename
2802 1040 0 3842 f02 smiapp-quirk.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suport for standard integer menu V4L2_CID_LINK_FREQ control.
The CSI2 link frequency value is specific for each sensor mode so the
sensor mode structure is extended to add this. The control is made
read-only and its value is updated when the sensor mode is changed -
on set_format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suport for standard V4L2_CID_PIXEL_RATE control. The pixel clock
frequency value is specific for each sensor mode so the sensor mode
structure is extended to add this. The control is read-only and its
value is updated when the sensor mode is changed - on set_format.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set media entity function to MEDIA_ENT_F_CAM_SENSOR.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for CCP2 connected SMIA sensors as found
on the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in v4l2_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Trivial fix to spelling mistake in v4l2_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove the soc_camera dependencies and move the diver to i2c
Lost features, fortunately not used or not critical on test platform:
- soc_camera power on/off callback - replaced with clock enable/disable
only, no support for platform provided regulators nor power callback,
- soc_camera sense request - replaced with arbitrarily selected default
master clock rate and pixel clock limit, no support for platform
requested values,
- soc_camera board flags - no support for platform requested mbus config
tweaks.
Tested on Amstrad Delta with now out of tree but still locally
maintained omap1_camera host driver.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Value assigned to variable _type_ at line 678 is overwritten at line 688
before it can be used. This makes such variable assignment useless.
Remove this variable assignment and fix some coding style issues.
Addresses-Coverity-ID: 1226968
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This one got applied twice, causing a build error with clang:
drivers/media/i2c/et8ek8/et8ek8_driver.c:1499:1: error: redefinition of '__mod_of__et8ek8_of_table_device_table'
Fixes: 9ae05fd1e7 ("[media] et8ek8: Export OF device ID as module aliases")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Commit e789029761 ("i2c: sh_mobile: don't send a stop condition by
default inside transfers") makes the i2c_sh_mobile I2C-adapter emit a
stop/start sequence between messages in a single transfer only when
explicitly requested with I2C_M_STOP.
This breaks the ov772x driver in the SH4 Migo-R board as the Omnivision
sensor uses the I2C-like SCCB protocol that doesn't support repeated
starts:
i2c-sh_mobile i2c-sh_mobile.0: Transfer request timed out
ov772x 0-0021: Product ID error 92:92
Fix it by marking the client as SCCB, forcing the emission of a
stop/start sequence between all messages.
As I2C_M_STOP requires the I2C adapter to support protocol mangling,
ensure that the I2C_FUNC_PROTOCOL_MANGLING functionality is available.
Tested on SH4 Migo-R board, with OV772x now successfully probing
soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0
ov772x 0-0021: ov7725 Product ID 77:21 Manufacturer ID 7f:a2
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove useless variable assignment in function tc358743_isr().
The value stored in variable _intstatus_ at line 1299 is
overwritten at line 1302, just before it can be used.
Addresses-Coverity-ID: 1397678
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is no need to split long string literals.
Join them back.
No functional change intended.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
DW9714 is a 10 bit DAC, designed for linear
control of voice coil motor.
This driver creates a V4L2 subdevice and
provides control to set the desired focus.
[Sakari Ailus: Add MAINTAINERS entry.]
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver for Omnivision's ov13858
sensor, the driver supports following features:
- manual exposure/gain(analog and digital) control support
- two link frequencies
- VBLANK/HBLANK support
- test pattern support
- media controller support
- runtime pm support
- supported resolutions
+ 4224x3136 at 30FPS
+ 2112x1568 at 30FPS(default) and 60FPS
+ 2112x1188 at 30FPS(default) and 60FPS
+ 1056x784 at 30FPS(default) and 60FPS
[Sakari Ailus: use V4L2_CID_DIGITAL_GAIN instead, add MAINTAINERS entry.]
Signed-off-by: Hyungwoo Yang <hyungwoo.yang@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver is based on ov5640_mipi.c from Freescale imx_3.10.17_1.0.0_beta
branch, modified heavily to bring forward to latest interfaces and code
cleanup.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
load is an unsigned integer. So, it is always bigger or equal
to zero, as reported by gcc:
drivers/media/i2c/max2175.c: In function 'max2175_refout_load_to_bits':
drivers/media/i2c/max2175.c:1272:11: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if (load >= 0 && load <= 40)
^~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch adds driver support for the MAX2175 chip. This is Maxim
Integrated's RF to Bits tuner front end chip designed for software-defined
radio solutions. This driver exposes the tuner as a sub-device instance
with standard and custom controls to configure the device.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As this is not in atomic context and it does not seem like a critical
timing setting a range of 1ms allows the timer subsystem to optimize
the hrtimer here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The async sub-device was not unregistered in ad5820_remove() as it should
have been; do it now. Also remove the now-redundant
v4l2_device_unregister_subdev().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
interrupts is listed as an optional property in the DT
binding, but in reality the driver didn't work without it.
The existing driver relied on having the interrupt line
connected to the SoC to trigger handling various events.
Add the option to poll the interrupt status register via
a timer if no interrupt source is defined.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Previously the mbus_fmt_code was set after the device was
registered. If a connected sub-device called tc358743_get_fmt
prior to that point it would get an invalid code back.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There was no way to query the supported mbus formats from this
driver. enum_mbus_code is the function to expose that, so
implement it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=+jBV
-----END PGP SIGNATURE-----
Merge tag 'media/v4.12-2' into patchwork
media fixes for v4.12-rc4
* tag 'media/v4.12-2': (598 commits)
[media] rc-core: race condition during ir_raw_event_register()
[media] cec: drop MEDIA_CEC_DEBUG
[media] cec: rename MEDIA_CEC_NOTIFIER to CEC_NOTIFIER
[media] cec: select CEC_CORE instead of depend on it
[media] rainshadow-cec: ensure exit_loop is intialized
[media] atomisp: don't treat warnings as errors
Linux 4.12-rc3
x86/ftrace: Make sure that ftrace trampolines are not RWX
x86/mm/ftrace: Do not bug in early boot on irqs_disabled in cpu_flush_range()
selftests/ftrace: Add a testcase for many kprobe events
kprobes/x86: Fix to set RWX bits correctly before releasing trampoline
ftrace: Fix memory leak in ftrace_graph_release()
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
PCI/msi: fix the pci_alloc_irq_vectors_affinity stub
blk-mq: Only register debugfs attributes for blk-mq queues
x86/timers: Move simple_udelay_calibration past init_hypervisor_platform
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Used to differentiate between models with 3 and 6 inputs.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Switch users of the v4l2_of_ APIs to the more generic v4l2_fwnode_ APIs.
Async OF matching is replaced by fwnode matching and OF matching support
is removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Benoit Parrot <bparrot@ti.com> # i2c/ov2569.c, am437x/am437x-vpfe.c and ti-vpe/cal.c
Tested-by: Hans Verkuil <hans.verkuil@cisco.com> # Atmel sama5d3 board + ov2640 sensor
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Initialize scalar variables _pid_ and _ver_ to avoid a possible misbehavior.
Addresses-Coverity-ID: 1324239
Addresses-Coverity-ID: 1324240
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In functions cx25840_initialize(), cx231xx_initialize(), and
cx23885_initialize(), the return value of create_singlethread_workqueue()
is used without validation. This may result in NULL dereference and cause
kernel crash. This patch fixes it.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The CEC framework is used by both drm and media. That makes it tricky
to get the dependencies right.
This patch moves the CEC_CORE and MEDIA_CEC_NOTIFIER config options
out of the media menu and instead drivers that want to use CEC should
select CEC_CORE and MEDIA_CEC_NOTIFIER (if needed).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid warnings like those:
drivers/media/pci/ddbridge/ddbridge-core.c: In function 'dvb_input_detach':
drivers/media/pci/ddbridge/ddbridge-core.c:787:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (input->fe) {
^
drivers/media/pci/ddbridge/ddbridge-core.c:792:2: note: here
case 4:
^~~~
...
On several cases, it is just that gcc 7.1 is not capable of
understanding the comment, but on other places, we need an
annotation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The below mentioned fix contains a small but severe bug,
fix it to make the driver work again.
Fixes: 3538aa6ecf ("[media] tc358743: fix register i2c_rd/wr functions")
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
devm_gpiod_get_optional() can return -ENOSYS if GPIOLIB is
disabled, causing probe to fail. Warn the user if this
happens.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Enabling vflip currently causes wrong colors.
It seems that (at least with the current sensor setup) REG04_VFLIP_IMG only
changes the vertical readout direction.
Because pixels are arranged RGRG... in odd lines and GBGB... in even lines,
either a one line shift or even/odd line swap is required, too, but
apparently this doesn't happen.
I finally figured out that this can be done manually by setting
REG04_VREF_EN.
Looking at hflip, it turns out that bit REG04_HREF_EN is set there
permanetly, but according to my tests has no effect on the pixel readout
order.
So my conclusion is that the current documentation of sensor register 0x04
is wrong (has changed after preliminary datasheet version 2.2).
I'm pretty sure that automatic vertical line shift/switch can be enabled,
too, but until anyone finds ot how this works, we have to stick with manual
switching.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ov2640_select_win() returns height and width values as part of struct
ov2640_win_size, so there is no point in modifying the passed height and
width parameters, too.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
HSIZE and VSIZE bits 0 to 2 and HSIZE bit 11 are encoded in DSP register
SIZEL.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to ov2640 software application notes, there are two Automatic
White Balance (AWB) modes, which are selected by DSP register 0xc7:
1) Simple AWB: assumes the average color is gray
+ independent from lens
- doesn't work well if captured area contains unbalanced colors
(e.g. large blue background)
2) Advanced AWB: uses color temperature information
+ more accurate, works with all image contents
- lens specific, requires calibration
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While we are at it, remove a misleading comment (copy/paste mistake)
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by kbuild test robot:
warning: (VIDEO_EM28XX_V4L2) selects VIDEO_OV2640 which has unmet direct dependencies (MEDIA_SUPPORT && VIDEO_V4L2 && I2C && GPIOLIB && MEDIA_CAMERA_SUPPORT)
The em28xx driver can use ov2640, but it doesn't depend
(or use) the GPIOLIB in order to power off/on the sensor.
So, as we want to allow both usages with and without
GPIOLIB, make its dependency optional.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Kconfig options for the CEC subsystem were a bit messy. In
addition there were two cec sources (cec-edid.c and cec-notifier.c)
that were outside of the media/cec directory, which was weird.
Move those sources to media/cec as well.
The cec-edid and cec-notifier functionality is now part of the cec
module and these are no longer separate modules.
Also remove the MEDIA_CEC_EDID config option and include it with the
main CEC config option (which defined CEC_EDID anyway).
Added static inlines to cec-edid.h for dummy functions when CEC_CORE
isn't defined.
CEC drivers should now depend on CEC_CORE.
CEC drivers that need the cec-notifier functionality must explicitly
select CEC_NOTIFIER.
The s5p-cec and stih-cec drivers depended on VIDEO_DEV instead of
CEC_CORE, fix that as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
After this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
alias: of:N*T*Ctoshiba,et8ek8C*
alias: of:N*T*Ctoshiba,et8ek8
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The OV5647 sensor from Omnivision supports up to 2592x1944 @ 15 fps, RAW 8
and RAW 10 output formats, and MIPI CSI-2 interface.
The driver adds support for 640x480 RAW 8.
Signed-off-by: Ramiro Oliveira <roliveir@synopsys.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ov5645 sensor from Omnivision supports up to 2592x1944
and CSI2 interface.
The driver adds support for the following modes:
- 1280x960
- 1920x1080
- 2592x1944
Output format is packed 8bit UYVY.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even if field order is set to V4L2_FIELD_ALTERNATE, the width and height
values in struct v4l2_mbus_framefmt still refer to frame size, not field
size.
Fixes: 4f57d27be2 ("[media] tvp5150: fix tvp5150_fill_fmt()")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
To let userspace propagate formats downstream in a media controller
scenario, the video source pad (now pad 1, DEMOD_PAD_VID_OUT) must allow
setting and getting the format. Incidentally, tvp5150_fill_fmt was
implemented for this pad, not for the new analog input pad (now pad 0,
DEMOD_PAD_IF_INPUT).
Fixes: 55606310e7 ("[media] tvp5150: create the expected number of pads")
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MC support is needed by the em28xx driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert v4l2_clk to normal clk and enable the clock.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert ov2640 to a standard subdev driver. The soc-camera driver no longer
uses this driver, so it can safely be converted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The colorspace is independent of whether YUV or RGB is sent to the SoC.
Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add DT support. Use it to get the reset and pwdn pins (if there are any).
Tested with one sensor requiring reset/pwdn and one sensor that doesn't
have reset/pwdn pins.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Get the clock for this sensor.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Drop unnecesary memset. Drop the unnecessary extendedmode check and
set the V4L2_CAP_TIMEPERFRAME capability.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add v4l2-async support for this driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use helper function to get driver private data from CEC
adapter.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
After changes to v4l2_clk API introduced in v4.1 by commits a37462b919
'[media] V4L: remove clock name from v4l2_clk API' and 4f528afcfb
'[media] V4L: add CCF support to the v4l2_clk API', ov6650 sensor
stopped responding because v4l2_clk_get(), still called with
depreciated V4L2 clock name "mclk", started to return respective CCF
clock instead of the V4l2 one registered by soc_camera. Fix it by
calling v4l2_clk_get() with NULL clock name.
Created and tested on Amstrad Delta against Linux-4.7-rc3 with
omap1_camera fixes.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
After this patch:
$ modinfo drivers/media/i2c/et8ek8/et8ek8.ko | grep alias
alias: i2c:et8ek8
alias: of:N*T*Ctoshiba,et8ek8C*
alias: of:N*T*Ctoshiba,et8ek8
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without calling tc358743_set_csi after stopping streaming (or calling
tc358743_s_dv_timings or tc358743_set_fmt from userspace after stopping
the stream), the i.MX6 MIPI CSI2 input fails waiting for lanes to enter
STOP state when streaming is started again.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While testing with CONFIG_UBSAN, I got this warning:
drivers/media/i2c/tc358743.c: In function 'tc358743_probe':
drivers/media/i2c/tc358743.c:1930:1: error: the frame size of 2480 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
The problem is that the i2c_rd8/wr8/rd16/... functions in this driver pass
a pointer to a local variable into a common function, and each call to one
of them adds another variable plus redzone to the stack.
I also noticed that the way this is done is broken on big-endian machines,
as we copy the registers in CPU byte order.
To address both those problems, I'm adding two helper functions for reading
a register of up to 32 bits with correct endianess and change all other
functions to use that instead. Just to be sure we don't get the problem
back with changed optimizations in gcc, I'm also marking the new functions
as 'noinline', although my tests with gcc-7 don't require that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix typos and add the following to the scripts/spelling.txt:
swithc||switch
swithced||switched
swithcing||switching
Link: http://lkml.kernel.org/r/1481573103-11329-3-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a compiler warning due to an unused but assigned variable.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The control for +5V Power detection must also be updated when the EDID is
not present.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Originally Toshiba told us that the only way to disable HDCP was to
set the receiver in repeater mode, that would make the authentication
fail because of missing software support. It has worked fine with all
the sources we and our customers has used, until it was reported
problems with Apple MacBook (Retina, 12-inch, Early 2015)
(https://support.apple.com/kb/SP712?locale=en_US&viewlocale=en_US)
with Apple A1612 USB type-C multiport adapter
(http://www.apple.com/shop/product/MJ1K2AM/A/usb-c-digital-av-multiport-adapter)
Finally Toshiba came up with a hidden bit that is named "Manual HDCP
authentication". In this patch the original "repeater mode" concept is
removed, and the new bit is set instead.
With his patch HDCP is disabled when connected to the Apple MacBook
and all other sources we have tested so far. The Apple MacBook is
constantly trying to authenticate, but fails and continues to transmit
unencrypted video.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The number of CSI lanes that should be used is set to the CSI_CONTROL
register by indirectly writing to the CSI_CONFW register. When the
number of lanes is read back from the CSI_CONTROL register the value
is usually correct, but we have seen that it suddenly is 1 for a short
moment before the correct value is restored again.
Toshiba have not figured out why that happen, but we have found it
safer to store the value in the driver.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
v4l2_i2c_subdev_init(...,&i@p)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_ops i;
File size before:
text data bss dec hex filename
2732 608 8 3348 d14 drivers/media/i2c/ml86v7667.o
File size after:
text data bss dec hex filename
3100 232 8 3340 d0c drivers/media/i2c/ml86v7667.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File size before:
text data bss dec hex filename
1809 872 0 2681 a79 drivers/media/i2c/ak881x.o
File size after:
text data bss dec hex filename
2185 496 0 2681 a79 drivers/media/i2c/ak881x.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_pad_ops structures are stored in the pad field
of the v4l2_subdev_ops structure and this field is of type const.
As the v4l2_subdev_pad_ops structures are never modified, they can be
declared as const.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_pad_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.pad=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_pad_ops i;
File size before:
text data bss dec hex filename
7633 512 20 8165 1fe5 media/i2c/m5mols/m5mols_core.o
File size after:
text data bss dec hex filename
7761 384 20 8165 1fe5 media/i2c/m5mols/m5mols_core.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This delay is in non-atomic context and it does not seem to be
time-critical so relax it to allow the timer subsystem to optimize
hrtimers.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2_subdev_{core/pad/video}_ops structures are stored in the
fields of the v4l2_subdev_ops structure which are of type const.
Also, v4l2_subdev_ops structure is passed to a function
having its argument of type const. As these structures are never
modified, so declare them as const.
Done using Coccinelle: (One of the scripts used)
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct v4l2_subdev_video_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
struct v4l2_subdev_ops obj;
@@
obj.video=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct v4l2_subdev_video_ops i;
File sizes before:
text data bss dec hex filename
7810 736 16 8562 2172 drivers/media/i2c/mt9p031.o
9652 736 24 10412 28ac drivers/media/i2c/mt9v032.o
4613 552 20 5185 1441 drivers/media/i2c/noon010pc30.o
2615 552 8 3175 c67 drivers/media/i2c/s5k6a3.o
File sizes after:
text data bss dec hex filename
8322 232 16 8570 217a drivers/media/i2c/mt9p031.o
10164 232 24 10420 28b4 drivers/media/i2c/mt9v032.o
4933 232 20 5185 1441 drivers/media/i2c/noon010pc30.o
2935 232 8 3175 c67 drivers/media/i2c/s5k6a3.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
ulseep_range() uses hrtimers and provides no advantage over msleep()
for larger delays. Fix up the 25ms delays here to use msleep() and
reduce the load on the hrtimer subsystem.
Link: http://lkml.org/lkml/2017/1/11/377
Reviwed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
