[ Upstream commit 4b2d8ca9208be636b30e924b1cbcb267b0740c93 ]
On this system the M.2 PCIe WiFi card isn't detected after reboot, only
after cold boot. reboot=pci fixes this behavior. In [0] the same issue
is described, although on another system and with another Intel WiFi
card. In case it's relevant, both systems have Celeron CPUs.
Add a PCI reboot quirk on affected systems until a more generic fix is
available.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202399
[ bp: Massage commit message. ]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/1524eafd-f89c-cfa4-ed70-0bde9e45eec9@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f31559af97a0eabd467e4719253675b7dccb8a46 ]
When fw_core_add_address_handler() fails, we need to destroy
the port by tty_port_destroy(). Also we need to unregister
the address handler by fw_core_remove_address_handler() on
failure.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20201221122437.10274-1-dinghao.liu@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c13d7ff81e6d2f01f62ccbfa49d1b8d87f274d0 ]
Those were only laptops and are very very unlikely to have ECC memory.
Currently, when the driver attempts to load, it issues:
EDAC amd64: Error: F1 not found: device 0x1601 (broken BIOS?)
because the PCI device is the wrong one (it uses the F15h default one).
So do not load the driver on them as that is pointless.
Reported-by: Don Curtis <bugrprt21882@online.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Don Curtis <bugrprt21882@online.de>
Link: http://bugzilla.opensuse.org/show_bug.cgi?id=1179763
Link: https://lkml.kernel.org/r/20201218160622.20146-1-bp@alien8.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 287431463e786766e05e4dc26d0a11d5f8ac8815 ]
The interrupt handling of the RS911x is particularly heavy. For each RX
packet, the card does three SDIO transactions, one to read interrupt
status register, one to RX buffer length, one to read the RX packet(s).
This translates to ~330 uS per one cycle of interrupt handler. In case
there is more incoming traffic, this will be more.
The drivers/mmc/core/sdio_irq.c has the following comment, quote "Just
like traditional hard IRQ handlers, we expect SDIO IRQ handlers to be
quick and to the point, so that the holding of the host lock does not
cover too much work that doesn't require that lock to be held."
The RS911x interrupt handler does not fit that. This patch therefore
changes it such that the entire IRQ handler is moved to the RX thread
instead, and the interrupt handler only wakes the RX thread.
This is OK, because the interrupt handler only does things which can
also be done in the RX thread, that is, it checks for firmware loading
error(s), it checks buffer status, it checks whether a packet arrived
and if so, reads out the packet and passes it to network stack.
Moreover, this change permits removal of a code which allocated an
skbuff only to get 4-byte-aligned buffer, read up to 8kiB of data
into the skbuff, queue this skbuff into local private queue, then in
RX thread, this buffer is dequeued, the data in the skbuff as passed
to the RSI driver core, and the skbuff is deallocated. All this is
replaced by directly calling the RSI driver core with local buffer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103180941.443528-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65277100caa2f2c62b6f3c4648b90d6f0435f3bc ]
In case RSI9116 SDIO WiFi operates in STA mode against Intel 9260 in AP mode,
the association fails. The former is using wpa_supplicant during association,
the later is set up using hostapd:
iwl$ cat hostapd.conf
interface=wlp1s0
ssid=test
country_code=DE
hw_mode=g
channel=1
wpa=2
wpa_passphrase=test
wpa_key_mgmt=WPA-PSK
iwl$ hostapd -d hostapd.conf
rsi$ wpa_supplicant -i wlan0 -c <(wpa_passphrase test test)
The problem is that the TX EAPOL data descriptor RSI_DESC_REQUIRE_CFM_TO_HOST
flag and extended descriptor EAPOL4_CONFIRM frame type are not set in case the
AP is iwlwifi, because in that case the TX EAPOL packet is 2 bytes shorter.
The downstream vendor driver has this change in place already [1], however
there is no explanation for it, neither is there any commit history from which
such explanation could be obtained.
[1] https://github.com/SiliconLabs/RS911X-nLink-OSD/blob/master/rsi/rsi_91x_hal.c#L238
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015111616.429220-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 16117beb16f01a470d40339960ffae1e287c03be upstream.
This looks like a left over debug print that tells us that HDMI is
enabled. Let's remove it as that's definitely not an error to have HDMI
enabled.
Cc: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Cc: Srinivasa Rao <srivasam@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Fixes: 7cb37b7bd0 ("ASoC: qcom: Add support for lpass hdmi driver")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210115034327.617223-2-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 322322d15b9b912bc8710c367a95a7de62220a72 upstream.
The original fixed-link.txt allowed a pause property for fixed link.
This has been missed in the conversion to yaml format.
Fixes: 9d3de3c583 ("dt-bindings: net: Add YAML schemas for the generic Ethernet options")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1l6W2G-0002Ga-0O@rmk-PC.armlinux.org.uk
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b23a32a63219f51a5298bc55a65ecee866e79d0 upstream.
dev_ifsioc_locked() is called with only RCU read lock, so when
there is a parallel writer changing the mac address, it could
get a partially updated mac address, as shown below:
Thread 1 Thread 2
// eth_commit_mac_addr_change()
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
// dev_ifsioc_locked()
memcpy(ifr->ifr_hwaddr.sa_data,
dev->dev_addr,...);
Close this race condition by guarding them with a RW semaphore,
like netdev_get_name(). We can not use seqlock here as it does not
allow blocking. The writers already take RTNL anyway, so this does
not affect the slow path. To avoid bothering existing
dev_set_mac_address() callers in drivers, introduce a new wrapper
just for user-facing callers on ioctl and rtnetlink paths.
Note, bonding also changes slave mac addresses but that requires
a separate patch due to the complexity of bonding code.
Fixes: 3710becf8a ("net: RCU locking for simple ioctl()")
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a93dcaada2ddb58dbc72652b42548adedd646d7a upstream.
Currently, the psample netlink skb is allocated with a size that does
not account for the nested 'PSAMPLE_ATTR_TUNNEL' attribute and the
padding required for the 64-bit attribute 'PSAMPLE_TUNNEL_KEY_ATTR_ID'.
This can result in failure to add attributes to the netlink skb due
to insufficient tail room. The following error message is printed to
the kernel log: "Could not create psample log message".
Fix this by adjusting the allocation size to take into account the
nested attribute and the padding.
Fixes: d8bed686ab ("net: psample: Add tunnel support")
CC: Yotam Gigi <yotam.gi@gmail.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Chris Mi <cmi@nvidia.com>
Link: https://lore.kernel.org/r/20210225075145.184314-1-cmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f176411401127a07a9360dec14eca448eb2e9d45 upstream.
In IEC 62439-3 EntryForgetTime is defined with a value of 400 ms. When a
node does not send any frame within this time, the sequence number check
for can be ignored. This solves communication issues with Cisco IE 2000
in Redbox mode.
Fixes: f421436a59 ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Marco Wenzel <marco.wenzel@a-eberle.de>
Reviewed-by: George McCollister <george.mccollister@gmail.com>
Tested-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210224094653.1440-1-marco.wenzel@a-eberle.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b385f325080157ab1b5f8ce1b1de07ce0d9e27 upstream.
2 bytes of the MTU are reserved for Atheros DSA tag, but DSA core
has already handled that since commit dc0fe7d47f.
Remove the unnecessary reservation.
Fixes: d51b6ce441 ("net: ethernet: add ag71xx driver")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210218034514.3421-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86dd9868b8788a9063893a97649594af93cd5aa6 upstream.
Support also transmitting frames using the custom "8899 A"
4 byte tag.
Qingfang came up with the solution: we need to pad the
ethernet frame to 60 bytes using eth_skb_pad(), then the
switch will happily accept frames with custom tags.
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reported-by: DENG Qingfang <dqfext@gmail.com>
Fixes: efd7fe68f0 ("net: dsa: tag_rtl4_a: Implement Realtek 4 byte A tag")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8043c845b63a2dd88daf2d2d268a33e1872800f0 upstream.
Looking through patchwork I don't see that there was any consensus to
use switchdev notifiers only in case of netlink provided port flags but
not sysfs (as a sort of deprecation, punishment or anything like that),
so we should probably keep the user interface consistent in terms of
functionality.
http://patchwork.ozlabs.org/project/netdev/patch/20170605092043.3523-3-jiri@resnulli.us/http://patchwork.ozlabs.org/project/netdev/patch/20170608064428.4785-3-jiri@resnulli.us/
Fixes: 3922285d96 ("net: bridge: Add support for offloading port attributes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 52557dbc7538ecceb27ef2206719a47a8039a335 upstream.
MPJ subflows are not exposed as fds to user spaces. As such,
incoming MPJ subflows are removed from the accept queue by
tcp_check_req()/tcp_get_cookie_sock().
Later tcp_child_process() invokes subflow_data_ready() on the
parent socket regardless of the subflow kind, leading to poll
wakeups even if the later accept will block.
Address the issue by double-checking the queue state before
waking the user-space.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/164
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d1be91254bbdd189796041561fd430f7553bb88 upstream.
tcp_rmem[1] has been changed to 131072, we should update the documentation
to reflect this.
Fixes: a337531b94 ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Zhibin Liu <zhibinliu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8ae7ddb48a1b81fd1e67da34a0cb59daf0445d6 upstream.
We do not need to wait for REG_MR completion, so remove the
SIGNAL flag.
Fixes: 9cb8374804 ("RDMA/rtrs: server: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-18-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aaed465f761700dace9ab39521013cddaae4f5a3 upstream.
We may want to add new flags, so it's better to use bitmask to check flags.
Fixes: 6a98d71dae ("RDMA/rtrs: client: main functionality")
Link: https://lore.kernel.org/r/20201217141915.56989-17-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b38041d50add1c881fbc60eb2be93b58fc58ea21 upstream.
For HB, there is no need to generate signal for completion.
Also remove a comment accordingly.
Fixes: c0894b3ea6 ("RDMA/rtrs: core: lib functions shared between client and server modules")
Link: https://lore.kernel.org/r/20201217141915.56989-16-jinpu.wang@cloud.ionos.com
Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Reported-by: Gioh Kim <gi-oh.kim@cloud.ionos.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1ba9da8f0f9a37d900ff7eff66482cf7de8015e upstream.
The current code would unnecessarily expand the address range. Consider
one example, (start, end) = (1G-2M, 3G+2M), and (vm_start, vm_end) =
(1G-4M, 3G+4M), the expected adjustment should be keep (1G-2M, 3G+2M)
without expand. But the current result will be (1G-4M, 3G+4M). Actually,
the range (1G-4M, 1G) and (3G, 3G+4M) would never been involved in pmd
sharing.
After this patch, we will check that the vma span at least one PUD aligned
size and the start,end range overlap the aligned range of vma.
With above example, the aligned vma range is (1G, 3G), so if (start, end)
range is within (1G-4M, 1G), or within (3G, 3G+4M), then no adjustment to
both start and end. Otherwise, we will have chance to adjust start
downwards or end upwards without exceeding (vm_start, vm_end).
Mike:
: The 'adjusted range' is used for calls to mmu notifiers and cache(tlb)
: flushing. Since the current code unnecessarily expands the range in some
: cases, more entries than necessary would be flushed. This would/could
: result in performance degradation. However, this is highly dependent on
: the user runtime. Is there a combination of vma layout and calls to
: actually hit this issue? If the issue is hit, will those entries
: unnecessarily flushed be used again and need to be unnecessarily reloaded?
Link: https://lkml.kernel.org/r/20210104081631.2921415-1-lixinhai.lxh@gmail.com
Fixes: 75802ca663 ("mm/hugetlb: fix calculation of adjust_range_if_pmd_sharing_possible")
Signed-off-by: Li Xinhai <lixinhai.lxh@gmail.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f02de4481da684aad6589aed0ea47bd1ab391c9 upstream.
At early boot stage, we have a whole PGDIR to map the kernel, so there
is no need to restrict the early mapping size to 128MB. Removing this
define also allows us to simplify some compile time logic.
This fixes large kernel mappings with a size greater than 128MB, as it
is the case for syzbot kernels whose size was just ~130MB.
Note that on rv64, for now, we are then limited to PGDIR size for early
mapping as we can't use PGD mappings (see [1]). That should be enough
given the relative small size of syzbot kernels compared to PGDIR_SIZE
which is 1GB.
[1] https://lore.kernel.org/lkml/20200603153608.30056-1-alex@ghiti.fr/
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 097b9146c0e26aabaa6ff3e5ea536a53f5254a79 upstream.
Avoid the assumption that ksize(kmalloc(S)) == ksize(kmalloc(S)): when
cloning an skb, save and restore truesize after pskb_expand_head(). This
can occur if the allocator decides to service an allocation of the same
size differently (e.g. use a different size class, or pass the
allocation on to KFENCE).
Because truesize is used for bookkeeping (such as sk_wmem_queued), a
modified truesize of a cloned skb may result in corrupt bookkeeping and
relevant warnings (such as in sk_stream_kill_queues()).
Link: https://lkml.kernel.org/r/X9JR/J6dMMOy1obu@elver.google.com
Reported-by: syzbot+7b99aafdcc2eedea6178@syzkaller.appspotmail.com
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Marco Elver <elver@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210201160420.2826895-1-elver@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5797e861e402fff2bedce4ec8b7c89f4248b6073 upstream.
syzbot is reporting that tomoyo's quota check is racy [1]. But this check
is tolerant of some degree of inaccuracy. Thus, teach KCSAN to ignore
this data race.
[1] https://syzkaller.appspot.com/bug?id=999533deec7ba6337f8aa25d8bd1a4d5f7e50476
Reported-by: syzbot <syzbot+0789a72b46fd91431bd8@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ef4c19d245f3dc233fd4be5acea436edd1d83d8 upstream.
syzbot found WARNINGs in several smackfs write operations where
bytes count is passed to memdup_user_nul which exceeds
GFP MAX_ORDER. Check count size if bigger than PAGE_SIZE.
Per smackfs doc, smk_write_net4addr accepts any label or -CIPSO,
smk_write_net6addr accepts any label or -DELETE. I couldn't find
any general rule for other label lengths except SMK_LABELLEN,
SMK_LONGLABEL, SMK_CIPSOMAX which are documented.
Let's constrain, in general, smackfs label lengths for PAGE_SIZE.
Although fuzzer crashes write to smackfs/netlabel on 0x400000 length.
Here is a quick way to reproduce the WARNING:
python -c "print('A' * 0x400000)" > /sys/fs/smackfs/netlabel
Reported-by: syzbot+a71a442385a0b2815497@syzkaller.appspotmail.com
Signed-off-by: Sabyrzhan Tasbolatov <snovitoll@gmail.com>
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 88a9e03beef22cc5fabea344f54b9a0dfe63de08 upstream.
An assert failure is triggered by syzkaller test due to
ATTR_KILL_PRIV is not cleared before xfs_setattr_size.
As ATTR_KILL_PRIV is not checked/used by xfs_setattr_size,
just remove it from the assert.
Signed-off-by: Yumei Huang <yuhuang@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 048c96e28674f15c0403deba2104ffba64544a06 upstream.
If a menu has more than 64 items, then don't check menu_skip_mask
for items 65 and up.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: syzbot+42d8c7c3d3e594b34346@syzkaller.appspotmail.com
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9dec0f48a75e0dadca498002d25ef4e143e60194 upstream.
prescaler larger than 8 would mean the carrier is at most 152Hz,
which does not make sense for IR carriers.
Reported-by: syzbot+6d31bf169a8265204b8d@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b7af295541d75535374325fd617944534853919 upstream.
The try_invoke_on_locked_down_task() function currently requires
that interrupts be enabled, but it is called with interrupts
disabled from rcu_print_task_stall(), resulting in an "IRQs not
enabled as expected" diagnostic. This commit therefore updates
try_invoke_on_locked_down_task() to use raw_spin_lock_irqsave() instead
of raw_spin_lock_irq(), thus allowing use from either context.
Link: https://lore.kernel.org/lkml/000000000000903d5805ab908fc4@google.com/
Link: https://lore.kernel.org/lkml/20200928075729.GC2611@hirez.programming.kicks-ass.net/
Reported-by: syzbot+cb3b69ae80afd6535b0e@syzkaller.appspotmail.com
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bef198f1b17d1bb89260bad947ef084c0a2d1a6 upstream.
syzbot is feeding invalid superblock data to JFS for mount testing.
JFS does not check several of the fields -- just assumes that they
are good since the JFS_MAGIC and version fields are good.
In this case (syzbot reproducer), we have s_l2bsize == 0xda0c,
pad == 0xf045, and s_state == 0x50, all of which are invalid IMO.
Having s_l2bsize == 0xda0c causes this UBSAN warning:
UBSAN: shift-out-of-bounds in fs/jfs/jfs_mount.c:373:25
shift exponent -9716 is negative
s_l2bsize can be tested for correctness. pad can be tested for non-0
and punted. s_state can be tested for its valid values and punted.
Do those 3 tests and if any of them fails, report the superblock as
invalid/corrupt and let fsck handle it.
With this patch, chkSuper() says this when JFS_DEBUG is enabled:
jfs_mount: Mount Failure: superblock is corrupt!
Mount JFS Failure: -22
jfs_mount failed w/return code = -22
The obvious problem with this method is that next week there could
be another syzbot test that uses different fields for invalid values,
this making this like a game of whack-a-mole.
syzkaller link: https://syzkaller.appspot.com/bug?extid=36315852ece4132ec193
Reported-by: syzbot+36315852ece4132ec193@syzkaller.appspotmail.com
Reported-by: kernel test robot <lkp@intel.com> # v2
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Cc: jfs-discussion@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb73d07148c405c293e576b40af37737faf23a6a upstream.
This is similar to commit
b21ebf2fb4 ("x86: Treat R_X86_64_PLT32 as R_X86_64_PC32")
but for i386. As far as the kernel is concerned, R_386_PLT32 can be
treated the same as R_386_PC32.
R_386_PLT32/R_X86_64_PLT32 are PC-relative relocation types which
can only be used by branches. If the referenced symbol is defined
externally, a PLT will be used.
R_386_PC32/R_X86_64_PC32 are PC-relative relocation types which can be
used by address taking operations and branches. If the referenced symbol
is defined externally, a copy relocation/canonical PLT entry will be
created in the executable.
On x86-64, there is no PIC vs non-PIC PLT distinction and an
R_X86_64_PLT32 relocation is produced for both `call/jmp foo` and
`call/jmp foo@PLT` with newer (2018) GNU as/LLVM integrated assembler.
This avoids canonical PLT entries (st_shndx=0, st_value!=0).
On i386, there are 2 types of PLTs, PIC and non-PIC. Currently,
the GCC/GNU as convention is to use R_386_PC32 for non-PIC PLT and
R_386_PLT32 for PIC PLT. Copy relocations/canonical PLT entries
are possible ABI issues but GCC/GNU as will likely keep the status
quo because (1) the ABI is legacy (2) the change will drop a GNU
ld diagnostic for non-default visibility ifunc in shared objects.
clang-12 -fno-pic (since [1]) can emit R_386_PLT32 for compiler
generated function declarations, because preventing canonical PLT
entries is weighed over the rare ifunc diagnostic.
Further info for the more interested:
https://github.com/ClangBuiltLinux/linux/issues/1210https://sourceware.org/bugzilla/show_bug.cgi?id=27169a084c0388e [1]
[ bp: Massage commit message. ]
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fangrui Song <maskray@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Link: https://lkml.kernel.org/r/20210127205600.1227437-1-maskray@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ea86f3defd55f141a44146e66cbf8ffb683d60da upstream.
We observed that some of virtio_gpu_object_shmem_init() allocations
can be rather costly - order 6 - which can be difficult to fulfill
under memory pressure conditions. Switch to kvmalloc_array() in
virtio_gpu_object_shmem_init() and let the kernel vmalloc the entries
array.
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20201105014744.1662226-1-senozhatsky@chromium.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Doug Horn <doughorn@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 056115daede8d01f71732bc7d778fb85acee8eb6 upstream.
The 0x5F is a new trackpoint report type used by some modules.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071511.32349-1-jingle.wu@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Nikolai Kostrigin <nickel@basealt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4c9062717feda88900b566463228d1c4910af6d upstream.
There are some version of Elan trackpads that send incorrect data when
in SMbus mode, unless they are switched to use 0x5f reports instead of
standard 0x5e. This patch implements querying device to retrieve chips
identifying data, and switching it, when needed to the alternative
report.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071531.32413-1-jingle.wu@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d050d049f8b8077025292c1ecf456c4ee7f96861 upstream.
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201202051634.490-2-wangzhiqiang.bj@bytedance.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d349f997686887906b1183b5be96933c5452362a upstream.
tcf_action_init_1() loads tc action modules automatically with
request_module() after parsing the tc action names, and it drops RTNL
lock and re-holds it before and after request_module(). This causes a
lot of troubles, as discovered by syzbot, because we can be in the
middle of batch initializations when we create an array of tc actions.
One of the problem is deadlock:
CPU 0 CPU 1
rtnl_lock();
for (...) {
tcf_action_init_1();
-> rtnl_unlock();
-> request_module();
rtnl_lock();
for (...) {
tcf_action_init_1();
-> tcf_idr_check_alloc();
// Insert one action into idr,
// but it is not committed until
// tcf_idr_insert_many(), then drop
// the RTNL lock in the _next_
// iteration
-> rtnl_unlock();
-> rtnl_lock();
-> a_o->init();
-> tcf_idr_check_alloc();
// Now waiting for the same index
// to be committed
-> request_module();
-> rtnl_lock()
// Now waiting for RTNL lock
}
rtnl_unlock();
}
rtnl_unlock();
This is not easy to solve, we can move the request_module() before
this loop and pre-load all the modules we need for this netlink
message and then do the rest initializations. So the loop breaks down
to two now:
for (i = 1; i <= TCA_ACT_MAX_PRIO && tb[i]; i++) {
struct tc_action_ops *a_o;
a_o = tc_action_load_ops(name, tb[i]...);
ops[i - 1] = a_o;
}
for (i = 1; i <= TCA_ACT_MAX_PRIO && tb[i]; i++) {
act = tcf_action_init_1(ops[i - 1]...);
}
Although this looks serious, it only has been reported by syzbot, so it
seems hard to trigger this by humans. And given the size of this patch,
I'd suggest to make it to net-next and not to backport to stable.
This patch has been tested by syzbot and tested with tdc.py by me.
Fixes: 0fedc63fad ("net_sched: commit action insertions together")
Reported-and-tested-by: syzbot+82752bc5331601cf4899@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+b3b63b6bff456bd95294@syzkaller.appspotmail.com
Reported-by: syzbot+ba67b12b1ca729912834@syzkaller.appspotmail.com
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20210117005657.14810-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b5553ace83cced775eefd0f3f18b5c6214ccf7a upstream.
Having two ring buffers per-peer means that every peer results in two
massive ring allocations. On an 8-core x86_64 machine, this commit
reduces the per-peer allocation from 18,688 bytes to 1,856 bytes, which
is an 90% reduction. Ninety percent! With some single-machine
deployments approaching 500,000 peers, we're talking about a reduction
from 7 gigs of memory down to 700 megs of memory.
In order to get rid of these per-peer allocations, this commit switches
to using a list-based queueing approach. Currently GSO fragments are
chained together using the skb->next pointer (the skb_list_* singly
linked list approach), so we form the per-peer queue around the unused
skb->prev pointer (which sort of makes sense because the links are
pointing backwards). Use of skb_queue_* is not possible here, because
that is based on doubly linked lists and spinlocks. Multiple cores can
write into the queue at any given time, because its writes occur in the
start_xmit path or in the udp_recv path. But reads happen in a single
workqueue item per-peer, amounting to a multi-producer, single-consumer
paradigm.
The MPSC queue is implemented locklessly and never blocks. However, it
is not linearizable (though it is serializable), with a very tight and
unlikely race on writes, which, when hit (some tiny fraction of the
0.15% of partial adds on a fully loaded 16-core x86_64 system), causes
the queue reader to terminate early. However, because every packet sent
queues up the same workqueue item after it is fully added, the worker
resumes again, and stopping early isn't actually a problem, since at
that point the packet wouldn't have yet been added to the encryption
queue. These properties allow us to avoid disabling interrupts or
spinning. The design is based on Dmitry Vyukov's algorithm [1].
Performance-wise, ordinarily list-based queues aren't preferable to
ringbuffers, because of cache misses when following pointers around.
However, we *already* have to follow the adjacent pointers when working
through fragments, so there shouldn't actually be any change there. A
potential downside is that dequeueing is a bit more complicated, but the
ptr_ring structure used prior had a spinlock when dequeueing, so all and
all the difference appears to be a wash.
Actually, from profiling, the biggest performance hit, by far, of this
commit winds up being atomic_add_unless(count, 1, max) and atomic_
dec(count), which account for the majority of CPU time, according to
perf. In that sense, the previous ring buffer was superior in that it
could check if it was full by head==tail, which the list-based approach
cannot do.
But all and all, this enables us to get massive memory savings, allowing
WireGuard to scale for real world deployments, without taking much of a
performance hit.
[1] http://www.1024cores.net/home/lock-free-algorithms/queues/intrusive-mpsc-node-based-queue
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d5a49aa6c3e264a93a7d08485d66e346be0969dd upstream.
In order to test ndo_start_xmit being called in parallel, explicitly add
separate tests, which should all run on different cores. This should
help tease out bugs associated with queueing up packets from different
cores in parallel. Currently, it hasn't found those types of bugs, but
given future planned work, this is a useful regression to avoid.
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee576c47db60432c37e54b1e2b43a8ca6d3a8dca upstream.
The icmp{,v6}_send functions make all sorts of use of skb->cb, casting
it with IPCB or IP6CB, assuming the skb to have come directly from the
inet layer. But when the packet comes from the ndo layer, especially
when forwarded, there's no telling what might be in skb->cb at that
point. As a result, the icmp sending code risks reading bogus memory
contents, which can result in nasty stack overflows such as this one
reported by a user:
panic+0x108/0x2ea
__stack_chk_fail+0x14/0x20
__icmp_send+0x5bd/0x5c0
icmp_ndo_send+0x148/0x160
In icmp_send, skb->cb is cast with IPCB and an ip_options struct is read
from it. The optlen parameter there is of particular note, as it can
induce writes beyond bounds. There are quite a few ways that can happen
in __ip_options_echo. For example:
// sptr/skb are attacker-controlled skb bytes
sptr = skb_network_header(skb);
// dptr/dopt points to stack memory allocated by __icmp_send
dptr = dopt->__data;
// sopt is the corrupt skb->cb in question
if (sopt->rr) {
optlen = sptr[sopt->rr+1]; // corrupt skb->cb + skb->data
soffset = sptr[sopt->rr+2]; // corrupt skb->cb + skb->data
// this now writes potentially attacker-controlled data, over
// flowing the stack:
memcpy(dptr, sptr+sopt->rr, optlen);
}
In the icmpv6_send case, the story is similar, but not as dire, as only
IP6CB(skb)->iif and IP6CB(skb)->dsthao are used. The dsthao case is
worse than the iif case, but it is passed to ipv6_find_tlv, which does
a bit of bounds checking on the value.
This is easy to simulate by doing a `memset(skb->cb, 0x41,
sizeof(skb->cb));` before calling icmp{,v6}_ndo_send, and it's only by
good fortune and the rarity of icmp sending from that context that we've
avoided reports like this until now. For example, in KASAN:
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0xa0e/0x12b0
Write of size 38 at addr ffff888006f1f80e by task ping/89
CPU: 2 PID: 89 Comm: ping Not tainted 5.10.0-rc7-debug+ #5
Call Trace:
dump_stack+0x9a/0xcc
print_address_description.constprop.0+0x1a/0x160
__kasan_report.cold+0x20/0x38
kasan_report+0x32/0x40
check_memory_region+0x145/0x1a0
memcpy+0x39/0x60
__ip_options_echo+0xa0e/0x12b0
__icmp_send+0x744/0x1700
Actually, out of the 4 drivers that do this, only gtp zeroed the cb for
the v4 case, while the rest did not. So this commit actually removes the
gtp-specific zeroing, while putting the code where it belongs in the
shared infrastructure of icmp{,v6}_ndo_send.
This commit fixes the issue by passing an empty IPCB or IP6CB along to
the functions that actually do the work. For the icmp_send, this was
already trivial, thanks to __icmp_send providing the plumbing function.
For icmpv6_send, this required a tiny bit of refactoring to make it
behave like the v4 case, after which it was straight forward.
Fixes: a2b78e9b2c ("sunvnet: generate ICMP PTMUD messages for smaller port MTUs")
Reported-by: SinYu <liuxyon@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/netdev/CAF=yD-LOF116aHub6RMe8vB8ZpnrrnoTdqhobEx+bvoA8AsP0w@mail.gmail.com/T/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20210223131858.72082-1-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1faba27f11c8da244e793546a1b35a9b1da8208e upstream.
The W=1 compilation of allmodconfig generates the following warning:
net/ipv6/icmp.c:448:6: warning: no previous prototype for 'icmp6_send' [-Wmissing-prototypes]
448 | void icmp6_send(struct sk_buff *skb, u8 type, u8 code, __u32 info,
| ^~~~~~~~~~
Fix it by providing function declaration for builds with ipv6 as a module.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d54ce6158e354f5358a547b96299ecd7f3725393 upstream.
Currently breakpoints in kernel .init.text section are not handled
correctly while allowing to remove them even after corresponding pages
have been freed.
Fix it via killing .init.text section breakpoints just prior to initmem
pages being freed.
Doug: "HW breakpoints aren't handled by this patch but it's probably
not such a big deal".
Link: https://lkml.kernel.org/r/20210224081652.587785-1-sumit.garg@linaro.org
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Suggested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Doug Anderson <dianders@chromium.org>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a6c6243b44a439bda4bf099032be35ebcf53406 upstream.
The BXT/GLK DPLL can't generate certain frequencies. We already
reject the 233-240MHz range on both. But on GLK the DPLL max
frequency was bumped from 300MHz to 594MHz, so now we get to
also worry about the 446-480MHz range (double the original
problem range). Reject any frequency within the higher
problematic range as well.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3000
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210203093044.30532-1-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
(cherry picked from commit 41751b3e5c1ac656a86f8d45a8891115281b729e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
