The SoC file defines the location and type of the ethernet
adapter, this should be in the per-board file, as it is by no
means necessary to have an ethernet adapter connected to this
memory space.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This extra data line for high-speed MMC transfers was unrouted,
set it up properly in the dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The idea to use two GPIO pins for bit-banged I2C is an S8815
pecularity, so move this over to the board-specific file and
out of the SoC core DTSI file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pushes the setting of the card detect GPIO pin down into
the top-level file for the board, since it is not a property of
the ASIC (which this DTSI is about) but a property of the board
design.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
John W. Linville says:
====================
pull request: wireless 2014-10-31
Please pull this small batch of spooky fixes intended for the 3.18
stream...boo!
Cyril Brulebois adds an rt2x00 device ID.
Dan Carpenter provides a one-line masking fix for an ath9k debugfs
entry.
Larry Finger gives us a package of small rtlwifi fixes which add some
bits that were left out of some feature updates that were included
in the merge window. Hopefully this isn't a sign that the rtlwifi
base is getting too big...
Marc Yang brings a fix for a temporary mwifiex stall when doing 11n
RX reordering.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver did not support the IFF_ALLMULTI flag which makes dynamic
multicast routing not work. Related to this, when enabling IFF_PROMISC
in switch mode, all registered multicast addresses are flushed, resulting
in only broadcast and unicast traffic being received.
A new cpsw_ale_set_allmulti function now scans through the ALE entry
table and adds/removes the host port from the unregistered multicast
port mask of each vlan entry depending on the state of IFF_ALLMULTI.
In promiscious mode, cpsw_ale_set_allmulti is used to force reception
of all multicast traffic in addition to the unicast and broadcast traffic.
With this change dynamic multicast and promiscious mode both work in
switch mode.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
0d961b3b52 (drivers: net: cpsw: fix buggy
loop condition) accidentally fixed a loop comparison in too many places
while fixing a real bug.
It was correct to fix the dual_emac mode section since there 'i' is used
as an index into priv->slaves which is a 0 based array.
However the other two changes (which are only used in switch mode)
are wrong since there 'i' is actually the ALE port number, and port 0
is the host port, while port 1 and up are the slave ports.
Putting the loop condition back in the switch mode section fixes it.
A comment has been added to point out the intent clearly to avoid future
confusion. Also a comment is fixed that said the opposite of what was
actually happening.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a driver supports reading EEPROM but no EEPROM is installed in the system,
the driver's get_eeprom_len function returns 0. ethtool will subsequently
try to read that zero-length EEPROM anyway. If the driver does not support
EEPROM access at all, this operation will return -EOPNOTSUPP. If the driver
does support EEPROM access but no EEPROM is installed, the operation will
return -EINVAL. Return -EOPNOTSUPP in both cases for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3b57de958e brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast and ucast filter entries)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.
Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.
And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VD_OP_GET_VTOC operation will succeed only if the vdisk backend has a
VTOC label, otherwise it will fail. In particular, it will return error
48 (ENOTSUP) if the disk has an EFI label. VTOC disk labels are already
handled by directly reading the disk in block/partitions/sun.c (enabled by
CONFIG_SUN_PARTITION which defaults to y on SPARC). Since port->label is
unused in the driver, remove the call and the field.
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kconfig already allows mpls to be built as module. Following patch
fixes Makefile to do same.
CC: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mpls gso handler needs to pull skb after segmenting skb.
CC: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core fixes from Ingo Molnar:
"The tree contains two RCU fixes and a compiler quirk comment fix"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make rcu_barrier() understand about missing rcuo kthreads
compiler/gcc4+: Remove inaccurate comment about 'asm goto' miscompiles
rcu: More on deadlock between CPU hotplug and expedited grace periods
Pull timer fixes from Thomas Gleixner:
"As you requested in the rc2 release mail the timer department serves
you a few real bug fixes:
- Fix the probe logic of the architected arm/arm64 timer
- Plug a stack info leak in posix-timers
- Prevent a shift out of bounds issue in the clockevents core"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM/ARM64: arch-timer: fix arch_timer_probed logic
clockevents: Prevent shift out of bounds
posix-timers: Fix stack info leak in timer_create()
tracing system does not support that and without checks, it can cause
an oops to be reported.
Rabin Vincent added checks in the return code on syscall events to make
sure that the system call number is within the range that tracing
knows about, and if not, simply ignores the system call.
The system call tracing infrastructure needs to be rewritten to handle these
cases better, but for now, to keep from oopsing, this patch will do.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUUt+4AAoJEEjnJuOKh9ld3HgH/0RL7neY1tp05+v0GRvABmGr
6T47GEmZi9NiQOWjFC4SxNHLQSjpQX7eLD2CC6bljDfFpgKiIqarWHegEBUoBF9K
Dlg2jPpCwwwKbTXlAKTmv9QTGzvBEYyVZxhSC7mEbziV4Rbt7CVZJlogVdeYP5y0
4mWyHJg11Dt9SiZJCIv8sIrx2Xka2eX+Aq30dwYd9JGco3vVCH8NZ09ZgYBHaxIm
YrL6yUVnHP3nqKiEL4qCMUqUzexzdwUhrGPddLANaSRTWT+EAGYPD113bA76jAKc
cd3eaFwFkmCA0yfmjjBSb23FsPvKHc7j6BtZA6Q3uKPZUVlX+DyVNisUfEnaLQs=
=9NTR
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"ARM has system calls outside the NR_syscalls range, and the generic
tracing system does not support that and without checks, it can cause
an oops to be reported.
Rabin Vincent added checks in the return code on syscall events to
make sure that the system call number is within the range that tracing
knows about, and if not, simply ignores the system call.
The system call tracing infrastructure needs to be rewritten to handle
these cases better, but for now, to keep from oopsing, this patch will
do"
* tag 'trace-fixes-v3.18-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/syscalls: Ignore numbers outside NR_syscalls' range
Pull documentation fixes from Jonathan Corbet:
"So this is my first pull request since I rashly agreed to look after
the documentation subtree. It contains some typo fixes, a few minor
documentation improvements, and, most importantly, fixes for a couple
of build problems in various bits of sample code.
I fully intend to start sending pull requests with signed tags.
However, due to poor planning on my part and the general obnoxiousness
of life, I'm 2000 miles away from my private key which is sitting on a
powered-down machine. This should be fixed before my next request.
Meanwhile git.lwn.net is a machine under my control, the patches are
all trivial, and all have done time in linux-next"
* tag 'docs-for-linus' of git://git.lwn.net/linux-2.6:
Documentation/SubmittingPatches: Reported-by tags and permission
Documentation: remove outdated references to the linux-next wiki
Documentation: Restrict TSC test code to x86
doc: kernel-parameters.txt: Add ide-generic.probe-mask
vdso: don't require 64-bit math in standalone test
Documentation: Add CONFIG_DEBUG_KMEMLEAK_DEFAULT_OFF case
Documentation: Add default kmemleak off case in kernel-parameters.txt
Docs: Document that the sticky bit is understood by hugetlbfs
DocBook: Reduce noise from make cleandocs
Documentation: fix vdso_standalone_test_x86 on 32-bit
Documentation: dt-bindings: Explain order in patch series
Documentation/ABI/testing/sysfs-ibft: fix a typo
For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.
[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 68da166491.
It turns out that the assertion about scope of regressions due to
always keeping keyboard controller in legacy mode was proven wrong.
There are laptops, such as Clevo W650SH, that only have internal
touchpad (no external PS/2 ports), that require active multiplexing
mode to switch the touchpad (Elantech) into native mode instead of
basic PS/2 emulation.
Reported-by: Roel Aaij <roel.aaij@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The irq function altera_ps2_rxint returns an irqreturn_t, so use the
same type for variable storing the return value.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In altera_ps2_close, the data register (offset 0) is written instead of
the control register (offset 4), leading to the RX interrupt not being
disabled. Fix this by calling writel() with the offset for the proper
register.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Expression haptic->pwm_dev->period * haptic->magnitude is of type
'unsigned int' and may overflow. We need to convert one of the operands
to u64 before multiplying, instead of casting result (potentially
overflown) to u64.
Reported by Coverity: CID 1248753
Acked-by : Jaewon Kim <jaewon02.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pablo Neira Ayuso says:
====================
netfilter/ipvs fixes for net
The following patchset contains fixes for netfilter/ipvs. This round of
fixes is larger than usual at this stage, specifically because of the
nf_tables bridge reject fixes that I would like to see in 3.18. The
patches are:
1) Fix a null-pointer dereference that may occur when logging
errors. This problem was introduced by 4a4739d56b ("ipvs: Pull
out crosses_local_route_boundary logic") in v3.17-rc5.
2) Update hook mask in nft_reject_bridge so we can also filter out
packets from there. This fixes 36d2af5 ("netfilter: nf_tables: allow
to filter from prerouting and postrouting"), which needs this chunk
to work.
3) Two patches to refactor common code to forge the IPv4 and IPv6
reject packets from the bridge. These are required by the nf_tables
reject bridge fix.
4) Fix nft_reject_bridge by avoiding the use of the IP stack to reject
packets from the bridge. The idea is to forge the reject packets and
inject them to the original port via br_deliver() which is now
exported for that purpose.
5) Restrict nft_reject_bridge to bridge prerouting and input hooks.
the original skbuff may cloned after prerouting when the bridge stack
needs to flood it to several bridge ports, it is too late to reject
the traffic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict the reject expression to the prerouting and input bridge
hooks. If we allow this to be used from forward or any other later
bridge hook, if the frame is flooded to several ports, we'll end up
sending several reject packets, one per cloned packet.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the packet is received via the bridge stack, this cannot reject
packets from the IP stack.
This adds functions to build the reject packet and send it from the
bridge stack. Comments and assumptions on this patch:
1) Validate the IPv4 and IPv6 headers before further processing,
given that the packet comes from the bridge stack, we cannot assume
they are clean. Truncated packets are dropped, we follow similar
approach in the existing iptables match/target extensions that need
to inspect layer 4 headers that is not available. This also includes
packets that are directed to multicast and broadcast ethernet
addresses.
2) br_deliver() is exported to inject the reject packet via
bridge localout -> postrouting. So the approach is similar to what
we already do in the iptables reject target. The reject packet is
sent to the bridge port from which we have received the original
packet.
3) The reject packet is forged based on the original packet. The TTL
is set based on sysctl_ip_default_ttl for IPv4 and per-net
ipv6.devconf_all hoplimit for IPv6.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
That can be reused by the reject bridge expression to build the reject
packet. The new functions are:
* nf_reject_ip6_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_ip6hdr_put(): to build the IPv6 header.
* nf_reject_ip6_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
That can be reused by the reject bridge expression to build the reject
packet. The new functions are:
* nf_reject_ip_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_iphdr_put(): to build the IPv4 header.
* nf_reject_ip_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds all clock defines for clockgen C0,D0,D2 and D3
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Author: David Jeffery <djeffery@redhat.com>
Changes to the basic direct I/O code have broken the raw driver when reading
to the end of a raw device. Instead of returning a short read for a read that
extends partially beyond the device's end or 0 when at the end of the device,
these reads now return EIO.
The raw driver needs the same end of device handling as was added for normal
block devices. Using blkdev_read_iter, which has the needed size checks,
prevents the EIO conditions at the end of the device.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
ARM: DT: STi: STiH416: Add DT node for ST's SATA device
Cc: devicetree@vger.kernel.org
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The MiPHY365x is a Generic PHY which can serve various SATA or PCIe
devices. It has 2 ports which it can use for either; both SATA, both
PCIe or one of each in any configuration.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
We supply two of these. The first is controlled by the System Configuration
registers and the second one provided is a more traditional 'memory mapped'
variant. Each are handled by they own sub-driver.
Signed-off-by: Ajit Pal Singh <ajitpal.singh@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The second controller is only present on the stih416 SoC. Also
mark this as non-removeable as its eMMC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Because the first sdhci controller is present on both stih415 and
stih416 SoC which can both populate the b2020 board, it can be
enabled in the generic DT file.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds device tree config for the sdhci controller
on the stih415 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the required pin config for the sdhci controller
present in the stih415 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds device tree config for both sdhci controllers
on the stih416 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This adds the required pin config for both SDHCI controllers on
the stih416 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the reset controller DT nodes for the powerdown,
softreset and picophy controllers.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The STiH407 is a STMicroelectronics Digital Consumer electronics
family, targetted at set-top-box and other audio/video applications.
This patch selects the reset controller driver for this family which
is essential to take various IP's on the SoC out of powerdown / reset.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
When screen objects are enabled, the bpp is assumed to be 32, otherwise
it is set to 16.
v2:
* Use u32 instead of u64 for assumed_bpp.
* Fixed mechanism to check for screen objects
* Limit the back buffer size to VRAM.
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Cc: <stable@vger.kernel.org>
