Some userspace will open a PCM device and then configure mixers
for routing before triggering. This patch allows userspace to do
this sequence.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix spelling mistake in "High-Performance" option of twl6040 power mode.
Signed-off-by: Simon Wilson <simonwilson@google.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use dev_ style logging throughout soc_new_pcm()
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If an audio interface is configured to use ASYNCCLK then update the
asynchronous sample rate rather than one of our primary sample rates.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mx27pdk board also has a mc13783 codec.
Add support for it and do a run-time machine type check to perform the correct
audiomux settings.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we don't set IMX_AUDMUX_V2_PTCR_TCLKDIR in the AUDMUX PTCR
register (means Tx clock pin is input), we don't need to set
IMX_AUDMUX_V2_PTCR_TCSEL as well. Since both i.MX35, i.MX51 and
i.MX6 datasheet says "When Tx clock pin set as an input, the TCSEL
settings are ignored".
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow any BCLK which can be divided down to generate LRCLK, not just the
lowest possible BCLK to clock out the samples.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the user to select which of the system clocks each AIF is referenced
to and constran the DAI to the set of frequencies which can be generated
from that clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
They're the rates for the BCLK, not for the sample rate, so rename so that
we don't confuse ourselves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements the spdif out driver for ST peripheral. This
peripheral implements IEC60958 standard
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The STA529 is a digital stereo class-D audio amplifier. It includes an
audio DSP, an ST proprietary high-efficiency class-D driver and CMOS
power output stage. It is intended for high-efficiency
digital-to-power-audio conversion for portable applications.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds missing register default values to cache.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds register and bit shift definitions in header file.
Changes are for TLV320AIC310x based on data sheet.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Leave it up to the machine driver to disable accessory detection if
desired, the common pattern is to have accessory detection be a wake
source.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since most new drivers are expected to use regmap and since frequently the
only thing we need to do in the CODEC probe function is configure the I/O
try to initialise the register I/O using regmap if the driver hasn't done
so after probe().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Use the dmaengine based Tegra APB DMA driver for
data transfer between SPI fifo and memory in
place of legacy Tegra APB DMA.
Because generic soc-dmaengine-pcm uses the DMAs API
based on dmaengine, using the exported APIs provided
by this generic driver.
The new driver is selected if legacy driver is not
selected and new dma driver is enabled through config
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Stereo is not yet supported by dapm widgets, so remove stereo code from
snd_soc_dapm_get_volsw(), and warn if stereo controls are detected.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current method for machine driver to register with the ASoC core is to use
snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_dapm_put_volsw() sets connect incorrectly in the case max > 1 with
invert. In that case, the raw disconnect value should be max, which corresponds
to the userspace value 0.
This use case currently does not appear upstream, but it could break
SOC_DAPM_SINGLE() or SOC_DAPM_SINGLE_TLV() elsewhere or in the future.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we fail to link when building as modules due to multiple
init/exit functions.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the support for spdif in audio codec.
Signed-off-by: vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patches for stubbing out the generic clock API still haven't been
applied so we need to either add ifdefs here or add a dependency until
someone decides to actually apply them.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This gets the registers set up as early as possible, mainly useful for the
GPIOs to ensure that they're in the correct mode.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is only one caller and this allows us to cleanly leave the CODEC
with the internal LDO powered down which is the default state we're
looking for and means that we can robustly disable the register cache
only when we either disable the LDO or power down the external
regulators.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get it done as early as possible, it's neater and minimises the time the
pins aren't configured as requested.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even though the WM8904 is able to use idle_bias_off during both probe
and resume we were needlessly leaving the device in standby mode. Instead
power the device down as soon as we've confirmed that we can talk to it
and don't manage the bias level at all over suspend and resume, the core
will take us down to our minimum power level.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
/HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
=H8t8
-----END PGP SIGNATURE-----
Merge tag 'v3.5-rc4' into for-3.6
Linux 3.5-rc4 contains some bug fixes which overlap with new features.
The WM5102 is a highly-integrated low-power audio system for smartphones,
tablets and other portable audio devices based on the Arizona platform.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Wolfson Arizona series of audio hub CODECs can share a large amount
of their driver code as the result of a common register map. This patch
adds some of this core support, providing a basis for the initial WM5102
audio driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We may as well print as many errors as we can in one go rather than
requiring developers to iterate through all their typos.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This patch implements the spdif IN driver for ST peripheral
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add support for the SPEAr ASoC pcm layer in ASoC
framework. The pcm layer uses common snd_dmaengine framework.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add support for synopsys I2S controller as per the ASoC
framework.
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the sound dmaengine pcm helper functions implement the pcm_pointer
callback by trying to count the number of elapsed periods. This is done by
advancing the stream position in the dmaengine callback by one period.
Unfortunately there is no guarantee that the callback will be called for each
elapsed period. It may be possible that under high system load it is only called
once for multiple elapsed periods. This patch addresses the issue by
implementing support for querying the current stream position directly from the
dmaengine driver. Since not all dmaengine drivers support reporting the stream
position yet the old period counting implementation is kept for now.
Furthermore the new mechanism allows to report the stream position with a
sub-period granularity, given that the dmaengine driver supports this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the sound dmaengine pcm helper functions implement the pcm_pointer
callback by trying to count the number of elapsed periods. This is done by
advancing the stream position in the dmaengine callback by one period.
Unfortunately there is no guarantee that the callback will be called for each
elapsed period. It may be possible that under high system load it is only called
once for multiple elapsed periods. This patch renames the current implementation
and documents its shortcomings and that it should not be used anymore in new
drivers.
The next patch will introduce a new snd_dmaengine_pcm_pointer which will be
implemented based on querying the current stream position from the dma device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver enables i2s mode support on blackfin bf6xx platform.
We reuse bf5xx-i2s-pcm.c as its i2s pcm driver because it's the same
for both bf5xx and bf6xx soc.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SPORT(Serial Port) module on bf6xx soc has a totally different ip
comparing to bf5xx soc. An individual SPORT module consists of two
independently configurable SPORT halves with identical functionality.
Each SPORT half can be configured for either transmitter or receiver.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
