Drop old license header and switch to SPDX-License-Identifier.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the ssm2603 data sheet (control register sequencing), the
digital core should be activated only after all necessary bits in the
power register are enabled, and a delay determined by the decoupling
capacitor on the VMID pin has passed. If the digital core is activated
too early, or even before the ADC is powered up, audible artifacts
appear at the beginning of the recorded signal.
The digital core is also needed for playback, so when recording starts
it may already be enabled. This means we cannot get the power sequence
correct when we want to be able to start recording after playback.
As a workaround put the MIC mute switch into the DAPM routes. This
way we can keep the recording disabled until the MIC Bias has settled
and thus get rid of audible artifacts.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
m.felsch@pengutronix.de: adapt commit message
m.felsch@pengutronix.de: drop of configuration as mentioned by Mark:
https://patchwork.kernel.org/patch/10407449/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSM2602 driver is broken on recent kernels (at least
since 4.9). User space applications such as amixer or
alsamixer get EIO when attempting to access codec
controls via the relevant IOCTLs.
Root cause of these failures is the regcache_hw_init
function in drivers/base/regmap/regcache.c, which
prevents regmap cache initalization from the
reg_defaults_raw element of the regmap_config structure
when registers are write only. It also disables the
regmap cache entirely when all registers are write only
or volatile as is the case for the SSM2602 driver.
Using the reg_defaults element of the regmap_config
structure rather than the reg_defaults_raw element to
initalize the regmap cache avoids the logic in the
regcache_hw_init function entirely. It also makes this
driver consistent with other ASoC codec drivers, as
this driver was the ONLY codec driver that used the
reg_defaults_raw element to initalize the cache.
Tested on Digilent Zybo Z7 development board which has
a SSM2603 codec chip connected to a Xilinx Zynq SoC.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Declare snd_soc_codec_driver structures as const as they are only passed
as an argument to the function snd_soc_register_codec. This argument is
of type const, so declare the structures with this property as const.
In file codecs/sn95031.c, snd_soc_codec_driver structure is also used in
a copy operation along with getting passed to snd_soc_register_codec.
So, it can be made const too.
Done using Coccinelle:
@match disable optional_qualifier@
identifier s;
position p;
@@
static struct snd_soc_codec_driver s@p={...};
@good1@
identifier match.s;
position p;
@@
snd_soc_register_codec(...,&s@p,...)
@bad@
identifier match.s;
position p!={match.p,good1.p};
@@
s@p
@depends on !bad disable optional_qualifier@
identifier match.s;
@@
static
+const
struct snd_soc_codec_driver s={...};
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DECLARE_TLV_DB_RANGE() has the advantage over using TLV_DB_RANGE_HEAD()
that it automatically calculates the number of items in the TLV and is
hence less prone to manual error.
Generate using the following coccinelle script
// <smpl>
@@
declarer name DECLARE_TLV_DB_RANGE;
identifier tlv;
constant x;
@@
-unsigned int tlv[] = {
- TLV_DB_RANGE_HEAD(x),
+DECLARE_TLV_DB_RANGE(tlv,
...
-};
+);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
All drivers have the same line at the end of the set_bias_level callback to
update the bias_level state. Move this update into
snd_soc_dapm_force_bias_level() and remove them from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds the necessary values to the constraint list and
register values to the coefficient table in order to
configure the device for 11.025kHz and 22.5kHz sample rates.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
The correct type (SSM2602/SSM2603/SSM2604) is passed down
from the ssm2602_spi_probe()/ssm2602_spi_probe() functions,
so use that instead of hardcoding it to SSM2602 in
ssm2602_probe().
Fixes: c924dc68f7 ("ASoC: ssm2602: Split SPI and I2C code into different modules")
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner. While we are at it also remove the
regcache_cache_only() calls from suspend/resume as there shouldn't be any IO
between suspend and resume.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some CODEC drivers like who act as the MFDs children are ignored
by this patch.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The array contains too many elements although it should have only
two.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register? Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus allows the registration of the other bus driver
to continue without problems if one of them fails.
This patch splits the ssm2602 driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.
While we are at it also cleanup the include section of the ssm2602 driver and
remove unneeded includes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The rate constraints in this driver are shared between all device instances. It
should not be (and is not) modified at runtime, so make them const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
SSM260x also supports 16kHz with external master clocks of 12.000MHz,
12.288MHz and 18.432MHz.
Add matching coefficients, update constraints and announced rates.
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let the core take care of applying sample rate and sample bits constraints
instead of open-coding this in the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Using the IS_ENABLED() macro can make the code shorter and simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ssm2602 uses regmap for caching not soc-cache, so we need to use
regcache_sync() instead of snd_soc_cache_sync().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mostly a one to one converion. On one occasion the patch replaces a
snd_soc_read-snd_soc_write sequence with regmap_update_bits though as it helps
to keep the conversion simple.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have never really updated that version number and probably never will, so
just remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Not all advertised rates are available for all sysclk frequencies. Add
additional sysclk based rate constraints.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to support CODEC<->CODEC links remove the assumption that there
is only a single CODEC on a DAI link by removing the use of the CODEC
pointer in the rtd from the CODEC drivers. They are already being passed
their DAI whenever they are passed an rtd and can get the CODEC from
there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The existence of this parameter is purely historical. None of the CODEC drivers
uses it and we always pass in the same value anyway, so it should be safe to
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the oscillator is always enabled and the clock output is always
disabled. This patch adds support for controlling the oscillator and clock
output state through snd_soc_dai_set_sysclk. Which makes it possible to
disable or enable them dynamically according to the requirements of the board
on which the CODEC is used.
This patch also slightly modifies the behavior as to when the oscillator is
going to be disabled in low-power states. Previously it would only be disabled
in BIAS_OFF, now it is also going to be disabled in BIAS_STANDBY, since no
components which depend on it should be active in this state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set the initial bias level to standby during CODEC probe instead of leaving the
CODEC powered off.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the the internal oscillator is powered down when entering BIAS_OFF
state, but not re-enabled when going back to BIAS_STANDBY. As a result the
CODEC will stop working after suspend if the internal oscillator is used to
generate the sysclock signal. This patch fixes it by clearing the appropriate
bit in the power down register when the CODEC is re-enabled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
The driver assumes that control_data points to the drivers i2c_client struct,
but this is no longer the case since the ASoC core has switched to regmap.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
sparse complains if 0 is used as a NULL pointer constant.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Also fix the maximum value for the capture volume control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Model the power supply for the digital core as a DAPM_SUPPLY widget. This allows
to cleanup the code a bit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SSM2603 is mostly register compatible with the SSM2602 and can be supported
by the current driver without any changes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The SSM2604 is basically a lightweight variant of the SSM2602 with a compatible
register layout. Thus we can easily support both devices by the same driver,
by providing a slightly set of controls, widgets and routes.
Compared to the SSM2602 the SSM2604 has no microphone input and no headphone
output.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is not required to have the codec powered at this stage and DAPM will power
the ADC and DAC down again after probe has run anyway.
Thus we avoid some unnecessary writes by this change.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some of the values in the default register cache did not represent the codecs
state after reset. This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There are currently two controls which allow selecting the capture source, one
as a normal control, the other as part of a DAPM_MUX widget.
Remove the normal control.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
