Only a single allowed and enabled protocol mask currently exists in
struct rc_dev, however to support a separate wakeup filter protocol two
of each are needed, ideally as an array.
Therefore make both rc_dev::allowed_protos and rc_dev::enabled_protocols
arrays, update all users to reference the first element
(RC_FILTER_NORMAL), and add a couple more helper functions for drivers
to use for setting the allowed and enabled wakeup protocols.
We also rename allowed_protos to allowed_protocols while we're at it,
which is more consistent with enabled_protocols.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add generic scancode filtering of RC input events, and fall back to
permitting any RC_FILTER_NORMAL scancode filter to be set if no s_filter
callback exists. This allows raw IR decoder events to be filtered, and
potentially allows hardware decoders to set looser filters and rely on
generic code to filter out the corner cases.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
On certain motherboards (mainly Intel NUC series) bios keeps the
Nuvoton CIR device disabled at boot.
This patch adds a call to kernel PNP layer to activate the device if it
is not already activated. This will improve the chances of the PNP probe
actually succeeding on Intel NUC platforms.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Propagate errors returned by drivers from the s_filter callback back to
userland when updating scancode filters. This allows userland to see
when the filter couldn't be updated, usually because it's not a valid
filter for the hardware.
Previously the filter was being updated conditionally on success of
s_filter, but the write always reported success back to userland.
Reported-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change 32bit NEC scancode format (used by Apple and TiVo remotes) to
encode the data with the correct bit order. Previously the raw bits were
used without being bit reversed, now each 16bit half is bit reversed
compared to before.
So for the raw NEC data:
(LSB/First) 0xAAaaCCcc (MSB/Last)
(where traditionally AA=address, aa=~address, CC=command, cc=~command)
We now generate the scancodes:
(MSB) 0x0000AACC (LSB) (normal NEC)
(MSB) 0x00AAaaCC (LSB) (extended NEC, address check wrong)
(MSB) 0xaaAAccCC (LSB) (32-bit NEC, command check wrong)
Note that the address byte order in 32-bit NEC scancodes is different to
that of the extended NEC scancodes. I chose this way as it maintains the
order of the bits in the address/command fields, and CC is clearly
intended to be the LSB of the command if the TiVo codes are anything to
go by so it makes sense for AA to also be the LSB.
The TiVo keymap is updated accordingly.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add and document a generic sysfs based scancode filtering interface for
making use of IR data matching hardware to filter out uninteresting
scancodes. Two filters exist, one for normal operation and one for
filtering scancodes which are permitted to wake the system from suspend.
The following files are added to /sys/class/rc/rc?/:
- filter: normal scancode filter value
- filter_mask: normal scancode filter mask
- wakeup_filter: wakeup scancode filter value
- wakeup_filter_mask: wakeup scancode filter mask
A new s_filter() driver callback is added which must arrange for the
specified filter to be applied at the right time. Drivers can convert
the scancode filter into a raw IR data filter, which can be applied
immediately or later (for wake up filters).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 1d184b0bc1 ([media] media: rc: add raw decoder for Sharp
protocol) added a new raw IR decoder for the sharp protocol, but didn't
add the code to load the module at init as is done for other raw
decoders, so add that code now.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are reports[1] that on some motherboards loading the nuvoton-cir
disables PS/2 keyboard input. This is caused by an erroneous write of
CIR_INTR_MOUSE_IRQ_BIT to ACPI control register.
According to datasheet the write enables mouse power management event
interrupts which will probably have ill effects if the motherboard has
only one PS/2 port with keyboard in it.
The cir hardware does not need mouse interrupts to function and should
not touch them. This patch removes the illegal writes and registry
definitions.
[1] http://ubuntuforums.org/showthread.php?t=2106277&p=12461912&mode=threaded#post12461912
Reported-by: Bruno Maire <bruno.maire@besonet.ch>
Tested-by: Bruno Maire <bruno.maire@besonet.ch>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
A number of recent bug reports involve usb_submit_urb() failing which was
only reported with debug parameter on. In addition, remove custom debug
function.
[m.chehab@samsung.com: patch rebased, as one of the patches on this
series need changes]
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a raw decoder for the Sharp protocol. It uses a pulse distance
modulation with a pulse of 320us and a bit period of 2ms for a logical 1
and 1ms for a logical 0. The first part of the message consists of a
5-bit address, an 8-bit command, and two other bits, followed by a 40ms
gap before the echo message which is an inverted version of the main
message except for the address bits.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since v3.12, specifically 153a60bb0f ([media] rc: add feedback led
trigger for rc keypresses), an LED trigger is activated on IR keydown
whether or not a keypress is generated (i.e. even if there's no matching
keycode). However the repeat and keyup logic isn't used unless there is
a keypress, which results in non-keypress keydown events turning on the
LED and not turning it off again.
On the assumption that the intent was for the LED only to light up on
valid key presses (you probably don't want it lighting up for the wrong
remote control for example), move the led_trigger_event() call inside
the keycode check.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix sparse warning:
drivers/media/rc/rc-main.c:27:1: sparse: symbol 'ir_core_dev_number' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Before changeset d8b4b5822f, the remote controller device numbers
were released when the device were unregistered. That helped to maintain
some sanity, as, when USB devices are replugged, the remote controller
would get the same number.
Restore the same behaviour.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some of the SOCs hold the IRB IP in softreset state by default.
For this IP to work driver needs to bring it out of softreset.
This patch adds support to reset the IP via reset framework.
Without this patch the driver can not work with SoCs which holds the IP
in softreset.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Emitting an OOM message isn't necessary after input_allocate_device
as there's a generic OOM and a dump_stack already done.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add usb id of Hauppauge WinTV-HVR-930C HD to mceusb RC driver.
This device has no IR transmitter (according to eeprom content decoded
by tveeprom).
Set the rc mapping to Hauppauge, every key of the deliviered remote
control works correctly.
[m.chehab@samsung.com: fix merge conflicts and unmangled whitespace]
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media build fixes from Mauro Carvalho Chehab:
"A series of patches that fix compilation on non-x86 archs.
While most of them are just build fixes, there are some fixes for real
bugs, as there are a number of drivers using dynamic stack allocation.
A few of those might be considered a security risk, if the i2c-dev
module is loaded, as someone could be sending very long I2C data that
could potentially overflow the Kernel stack. Ok, as using /dev/i2c-*
devnodes usually requires root on usual distros, and exploiting it
would require a DVB board or USB stick, the risk is not high"
* 'topic/kbuild-fixes-for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (28 commits)
[media] platform drivers: Fix build on frv arch
[media] lirc_zilog: Don't use dynamic static allocation
[media] mxl111sf: Don't use dynamic static allocation
[media] af9035: Don't use dynamic static allocation
[media] af9015: Don't use dynamic static allocation
[media] dw2102: Don't use dynamic static allocation
[media] dibusb-common: Don't use dynamic static allocation
[media] cxusb: Don't use dynamic static allocation
[media] v4l2-async: Don't use dynamic static allocation
[media] cimax2: Don't use dynamic static allocation
[media] tuner-xc2028: Don't use dynamic static allocation
[media] tuners: Don't use dynamic static allocation
[media] av7110_hw: Don't use dynamic static allocation
[media] stv090x: Don't use dynamic static allocation
[media] stv0367: Don't use dynamic static allocation
[media] stb0899_drv: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] dvb-frontends: Don't use dynamic static allocation
[media] s5h1420: Don't use dynamic static allocation
[media] uvc/lirc_serial: Fix some warnings on parisc arch
...
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the following warnings:
drivers/media/rc/fintek-cir.c: In function 'fintek_cr_write':
drivers/media/rc/fintek-cir.c:45:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c:46:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c: In function 'fintek_cr_read':
drivers/media/rc/fintek-cir.c:54:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c:55:8: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c: In function 'fintek_config_mode_enable':
drivers/media/rc/fintek-cir.c:80:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c:81:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/fintek-cir.c: In function 'fintek_config_mode_disable':
drivers/media/rc/fintek-cir.c:87:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_cr_write':
drivers/media/rc/nuvoton-cir.c:45:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c:46:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_cr_read':
drivers/media/rc/nuvoton-cir.c:52:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c:53:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_efm_enable':
drivers/media/rc/nuvoton-cir.c:74:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c:75:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_efm_disable':
drivers/media/rc/nuvoton-cir.c:81:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c: In function 'nvt_select_logical_dev':
drivers/media/rc/nuvoton-cir.c:91:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/media/rc/nuvoton-cir.c:92:2: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Those are caused because the I/O port is u32, instead of u8.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Simplify the logic that calculates the carrier, and removes a warning
on avr32 arch:
drivers/media/rc/iguanair.c: In function 'iguanair_set_tx_carrier':
drivers/media/rc/iguanair.c:304: warning: 'sevens' may be used uninitialized in this function
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support to ST RC driver, which is basically a IR/UHF
receiver and transmitter. This IP (IRB) is common across all the ST
parts for settop box platforms. IRB is embedded in ST COMMS IP block.
It supports both Rx & Tx functionality.
This driver adds only Rx functionality via LIRC codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
At least technisat-usb2.c doesn't set these...
Signed-off-by: Juergen Lock <nox@jelal.kn-bremen.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Note that with the rc-feedback trigger, the cir-rx trigger is now
redundant. The cir-tx trigger is not used by default; if this
functionality is desired then it should exist in rc-core, not in
a driver.
Also make sure that the led is suspended on suspend.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Many devices with an ir receiver also have a feedback led. Add the
led trigger to support this.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The length in the header excludes the header itself, so we're getting
spurious readings.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The use case is simple, if any rc device has allowed protocols =
RC_TYPE_LIRC and map_name = RC_MAP_LIRC set, the driver open will be never
called. The reason for this is, all of the key maps except lirc have some
KEYS in there map, so during rc_register_device process these keys are
matched against the input drivers and open is performed, so for the case
of RC_MAP_EMPTY, a vt/keyboard is matched and the driver open is
performed.
In case of lirc, there is no match and result is that there is no open
performed, however the lirc-dev will go ahead and create a /dev/lirc0
node. Now when lircd/mode2 opens this device, no data is available
because the driver was never opened.
Other case pointed by Sean Young, As rc device gets opened via the
input interface. If the input device is never opened (e.g. embedded with
no console) then the rc open is never called and lirc will not work
either. So that's another case.
lirc_dev seems to have no link with actual rc device w.r.t open/close.
This patch adds rc_dev pointer to lirc_driver structure for cases like
this, so that it can do the open/close of the real driver in accordance
to lircd/mode2 open/close.
Without this patch its impossible to open a rc device which has
RC_TYPE_LIRC ad RC_MAP_LIRC set.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds user count to rc_dev structure, the reason to add this
new member is to allow other code like lirc to open rc device directly.
In the existing code, rc device is only opened by input subsystem which
works ok if we have any input drivers to match. But in case like lirc
where there will be no input driver, rc device will be never opened.
Having this user count variable will be usefull to allow rc device to be
opened from code other than rc-main.
This patch also adds rc_open and rc_close functions for other drivers
like lirc to open and close rc devices. This functions safely increment
and decrement the user count. Other driver wanting to open rc device
should call rc_open and rc_close, rather than directly modifying the
rc_dev structure.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All lirc drivers that can transmit, return EINVAL when they are passed
more than IR data than they can send. That is, except for two drivers
which I touched.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The lirc interface allows 255 u32 spaces and pulses, which are usec. If
the driver can handle this (e.g. winbond-cir) you can produce hours of
meaningless IR data and there is no method of interrupting it.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In an usb disconnect handler, the urbs have already been cancelled so the
attempt to disable the IR receiver just results in errors:
[ 899.638862] redrat3 7-2:1.0: redrat3_send_cmd: Error sending rr3 cmd res -110, data 0
[ 899.638870] redrat3 7-2:1.0: redrat3_disable_detector: detector status: 251, should be 0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This way to only way to get debug info is to use dynamic debug, but I
left debugging prints to debug hardware issues, and so I want this to be
enabled by module param.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It doesn't hurt and on my notebook despite clearing the
wake flag the remote still wakes up the system.
This way it doesn't.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While we can delay IRQ intialization, we need the interrupt number
right away because unusually hardware have programable interrupt number,
and thus we give it the number that was allocated by BIOS
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the keytable for the remote that comes with the Delock 61959.
NEC protocol with address 0x866b.
Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
send_packet() is used during initialization, before send_packet_delay
is set. So, move ictx->send_packet_delay to happen earlier.
[mchehab@redhat.com: fold two patches into one to make git history clearer]
Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix mceusb_cmdsize() which returns incorrect datasize=0 for
sub-commands MCE_RSP_GETPORTSTATUS, MCE_RSP_GETWAKESOURCE,
MCE_RSP_EQDEVDETAILS, MCE_RSP_EQEMVER, and MCE_RSP_EQIRNUMPORTS.
While here, change mceusb_cmdsize() name to reflect that it returns
data size not cmd size.
Signed-off-by: William Steidtmann <billstei@hbci.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is very similar than rc-msi-digivox-iii but new keytable is needed
as there is one existing scancode mapped to different button. Also that
one has less buttons.
NEC extended protocol with address 0x61d6.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument, the subsequently
call to rc_free_device() on the same variable will cause a double
free bug. Fix by set argument to NULL, thus when fall through to
rc_free_device(), nothing will be done there.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument, the subsequently
call to rc_free_device() on the same variable will cause a double
free bug. Fix by set argument to NULL, thus when fall through to
rc_free_device(), nothing will be done there.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument, the subsequently
call to rc_free_device() on the same variable will cause a double
free bug. Fix by set argument to NULL, thus when fall through to
rc_free_device(), nothing will be done there.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument, the subsequently
call to rc_free_device() on the same variable will cause a double
free bug. Fix by set argument to NULL, thus when fall through to
rc_free_device(), nothing will be done there.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rc_unregister_device already calls rc_free_device to free the passed
device. But in one of ttusbir's probe fail paths, we call
rc_unregister_device _and_ rc_free_device. This is wrong and results
in a double free.
Instead, set rc to NULL resulting in rc_free_device being a noop.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into patchwork
Linux 3.9-rc5
* tag 'v3.9-rc5': (1080 commits)
Linux 3.9-rc5
Revert "lockdep: check that no locks held at freeze time"
dw_dmac: adjust slave_id accordingly to request line base
dmaengine: dw_dma: fix endianess for DT xlate function
PNP: List Rafael Wysocki as a maintainer
rbd: don't zero-fill non-image object requests
ia64 idle: delete stale (*idle)() function pointer
Btrfs: don't drop path when printing out tree errors in scrub
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
Revert "mm: introduce VM_POPULATE flag to better deal with racy userspace programs"
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
mg_disk: fix error return code in mg_probe()
Btrfs: fix wrong return value of btrfs_lookup_csum()
Btrfs: fix wrong reservation of csums
Btrfs: fix double free in the btrfs_qgroup_account_ref()
Btrfs: limit the global reserve to 512mb
Btrfs: hold the ordered operations mutex when waiting on ordered extents
Btrfs: fix space accounting for unlink and rename
Btrfs: fix space leak when we fail to reserve metadata space
...
store_protocols() treats dev->rc_map.rc_type as a bitmap which is wrong for
two reasons. First of all, it is pretty bogus to change the protocol type of
the keymap just because the hardware has been asked to decode a different
protocol.
Second, dev->rc_map.rc_type is an enum (i.e. a single protocol) as pointed
out by James Hogan <james.hogan@imgtec.com>.
Fix both issues by introducing a separate enabled_protocols member to
struct rc_dev.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some imon devices (like 15c2:0036) need a higher delay between
send_packet calls.
Default value is still 5ms to avoid regressions on already working
hardware.
Also use interruptible wait to avoid load average going too high (and
let caller handle signals).
Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The name is already misleading and will be more so in the future as the
connection to the input subsystem is obscured away further.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
rc-core is a subsystem so it should be registered earlier if built into the
kernel.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In stead of doing a memcpy from #defined offset, declare structs which
describe the incoming and outgoing data accurately.
Tested on first generation RedRat.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The redrat hardware cannot handle periods of larger than 32767us,
limit appropriately. Also fix memory leak in redrat3_get_timeout.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver can be enabled on OMAP1 at the moment, which breaks
allyesconfig for that platform. Let's mark it OMAP2PLUS-only
in Kconfig, since that is the only thing it builds on.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Even if bus is not hot-pluggable, the devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
Similarly probe() methods should not be marked __init unless
platform_driver_probe() is used.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
file argument is a struct file being passed to ->open() or
already opened; none of the checks in lirc_get_pdata()
can fail.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull media updates from Mauro Carvalho Chehab:
- Some cleanups at V4L2 documentation
- new drivers: ts2020 frontend, ov9650 sensor, s5c73m3 sensor,
sh-mobile veu mem2mem driver, radio-ma901, davinci_vpfe staging
driver
- Lots of missing MAINTAINERS entries added
- several em28xx driver improvements, including its conversion to
videobuf2
- several fixups on drivers to make them to better comply with the API
- DVB core: add support for DVBv5 stats, allowing the implementation of
statistics for new standards like ISDB
- mb86a20s: add statistics to the driver
- lots of new board additions, cleanups, and driver improvements.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (596 commits)
[media] media: Add 0x3009 USB PID to ttusb2 driver (fixed diff)
[media] rtl28xxu: Add USB IDs for Compro VideoMate U620F
[media] em28xx: add usb id for terratec h5 rev. 3
[media] media: rc: gpio-ir-recv: add support for device tree parsing
[media] mceusb: move check earlier to make smatch happy
[media] radio-si470x doc: add info about v4l2-ctl and sox+alsa
[media] staging: media: Remove unnecessary OOM messages
[media] sh_vou: Use vou_dev instead of vou_file wherever possible
[media] sh_vou: Use video_drvdata()
[media] drivers/media/platform/soc_camera/pxa_camera.c: use devm_ functions
[media] mt9t112: mt9t111 format set up differs from mt9t112
[media] sh-mobile-ceu-camera: fix SHARPNESS control default
Revert "[media] fc0011: Return early, if the frequency is already tuned"
[media] cx18/ivtv: fix regression: remove __init from a non-init function
[media] em28xx: fix analog streaming with USB bulk transfers
[media] stv0900: remove unnecessary null pointer check
[media] fc0011: Return early, if the frequency is already tuned
[media] fc0011: Add some sanity checks and cleanups
[media] fc0011: Fix xin value clamping
Revert "[media] [PATH,1/2] mxl5007 move reset to attach"
...
This patch adds device tree parsing for gpio_ir_recv platform_data and
the mandatory binding documentation. It basically follows what we already
have for e.g. gpio_keys. All required device tree properties are OS
independent but an optional property allows linux specific support for rc
maps.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Smatch complains that "cmdbuf[cmdcount - length]" might go past the end
of the array. It's an easy warning to silence by moving the limit
check earlier.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If more than 127 different lengths are transmitted then the driver causes
an overrun on sample_lens. Try to send as much as possible and return the
amount sent.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This transceiver expects the set IR TX ports and IR data as seperate
packets, like the Windows driver does. Remove unnecessary kzalloc.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The GET_REVISION command puts the device in an unresponsive state,
although it continues to report any IR activity. Note that GET_REVISION
command is not documented, nor is any possible response to it parsed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On cold boot the device does not initialize until the first packet is
received, and that packet is not processed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A sample resolution of 2us generates more than 300 interrupts per key
and this resolution is not needed unless carrier reports are enabled.
Revert to a resolution of 10us unless carrier reports are needed. This
generates up to a fifth of the interrupts.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Events for the iMon Knob pad where not correctly interpreted on ARM,
resulting in buggy mouse movements (cursor going straight out of the
screen), key pad only generating KEY_RIGHT and KEY_DOWN events.
A reproducer is:
int main(int argc, char ** argv)
{
char rel_x = 0x00; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x = 0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x |= ~0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
return 0;
}
(running on x86 or amd64)
$ ./test
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:-1 @test.c:8
(running on armv6)
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:255 @test.c:8
Forcing the rel_x and rel_y variables as signed char fixes the issue.
Reference: http://www.arm.linux.org.uk/docs/faqs/signedchar.php
Signed-off-by: Alexandre Lissy <alexandrelissy@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
We still need to fix up few places for multiplatform support,
but that can proceed separately. Fix the issue by making the
problem drivers depends !ARCH_MULTIPLATFORM for now.
The remaining pieces that are not multiplatform compatible
for omap2+ SoCs are:
1. Some drivers are using custom omap_dm_timer calls
There are two drivers that are directly usign omap hardware
timers for PWM and DSP clocking: drivers/media/rc/ir-rx51.c and
drivers/staging/tidspbridge/core/dsp-clock.c. These can be
fixed for multiplatform by allowing a minimal set of hardware
timers to be accessed, and for some functionality by using the
hrtimer framework.
2. Hardware OMAP4_ERRATA_I688 needs to be fixed up
This can't be enabled for multiplatform configurations in
it's current form. It may be possible to fix it up to do
instruction replacement early on during init. Luckily it
looks like this errata does not seem to get hit with
mainline kernel code alone at least currently.
3. Legacy header needed for omap-sham.c
Looks like it still needs mach/irqs.h for omap1 that
does not exist for multiplatform systems. Just ifdef
it for now.
4. Mailbox is waiting to get moved to drivers
Disable it for now to avoid adding a dependency to the
mailbox patches.
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Sean Young <sean@mess.org>
Cc: "Víctor Manuel Jáquez Leal" <vjaquez@igalia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
[tony@atomide.com: updated to disable mailbox]
Signed-off-by: Tony Lindgren <tony@atomide.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During modiles initialization rc-core schedules work which calls
request_module() several times to load ir-*-decoder modules, but
it does not wait or cancel this work on module unloading.
rc-core should use request_module_nowait() instead, because it
anyway cannot load modules synchronously or cancel/wait pending
work on unloading, because this leads to deadlock on modules_mutex
between several "modprobe" processes.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This error path is missing the unlock.
[mchehab@redhat.com: Merged two equal patches into one]
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ1QqgAAoJEHm+PkMAQRiG3GMIAJZjN2+0EGFpcq0LDrjIMyLG
PFuCkn9wNybAVR38DuVJkYclLclN2T1CevWZib+GgRLZO2IU5Qu1xh+fCLRn1u5i
qrxq8g4HYVMYXDixdZzXA2eXCLF7YLzPEdlowoBItGl9OJjQdzk3zBATtJGxfKaP
zvmaXP0CyoQekrZmmpMEl2/PLY/X0Ett6I5tlKcTvYKbbowG1SoAwVEVokCZC/vi
I+y8/8M68eDfOfYZ8BoRd5Lsygxfw8uvOce4qUeKawiZPO8bWP1s9NFyK6Ank6+s
hNXM9dNm6l0JfS+Ykb2FXleuEmOaaloRswOxukU1gKC3V0HdxwKx0Ir4P3z1dHM=
=5Iln
-----END PGP SIGNATURE-----
Merge tag 'v3.8-rc1' into staging/for_v3.9
Linux 3.8-rc1
* tag 'v3.8-rc1': (10696 commits)
Linux 3.8-rc1
Revert "nfsd: warn on odd reply state in nfsd_vfs_read"
ARM: dts: fix duplicated build target and alphabetical sort out for exynos
dm stripe: add WRITE SAME support
dm: remove map_info
dm snapshot: do not use map_context
dm thin: dont use map_context
dm raid1: dont use map_context
dm flakey: dont use map_context
dm raid1: rename read_record to bio_record
dm: move target request nr to dm_target_io
dm snapshot: use per_bio_data
dm verity: use per_bio_data
dm raid1: use per_bio_data
dm: introduce per_bio_data
dm kcopyd: add WRITE SAME support to dm_kcopyd_zero
dm linear: add WRITE SAME support
dm: add WRITE SAME support
dm: prepare to support WRITE SAME
dm ioctl: use kmalloc if possible
...
Conflicts:
MAINTAINERS
We recently introduced a new return -ENODEV in this function but we need
to unlock before returning.
[mchehab@redhat.com: found two patches with the same fix. Merged SOB's/acks into one patch]
Acked-by: Herton R. Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Douglas Bagnall <douglas@paradise.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This should fix a potential race condition, when the irq handler
triggers while rc_register_device is still setting up the rdev->raw
device.
This crash has not been observed in practice, but there should be a very
small window where it could occur. Since ir_raw_event_store_with_filter
checks if rdev->raw is not NULL before using it, this bug is not
triggered if the request_irq triggers a pending irq directly (since
rdev->raw will still be NULL then).
This commit was tested on nuvoton-cir only.
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a problem in fintek-cir and nuvoton-cir where the
irq handler would trigger during module load before the rdev member was
set, causing a NULL pointer crash.
It seems this crash is very reproducible (just bombard the receiver with
IR signals during module load), probably because when request_irq is
called, any pending intterupt is handled immediately, before
request_irq returns and rdev can be set.
This same crash was supposed to be fixed by commit
9ef449c6b3 ("[media] rc: Postpone ISR
registration"), but the crash was still observed on the nuvoton-cir
driver.
This commit was tested on nuvoton-cir only.
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before, labels were simply numbered. Now, the labels are named after the
cleanup action they'll perform (first), based on how the winbond-cir
driver does it. This makes the code a bit more clear and makes changes
in the ordering of labels easier to review.
This change is applied only to the rc drivers that do significant
cleanup in their probe functions: ati-remote, ene-ir, fintek-cir,
gpio-ir-recv, ite-cir, nuvoton-cir.
This commit should not change any code, it just renames goto labels.
[mchehab@redhat.com: removed changes at gpio-ir-recv.c, due to
merge conflicts]
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
