This patch is using the DCB netlink to set rate limit per ETS TC
Values are accepted in Kbps and rounded up to the nearest multiply of 100Mbps.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since vlan egress map is only good for tagged traffic, need to have other
mapping to be used by untagged traffic.
For that, the driver uses sch_mqprio mapping. This mapping could be set by
using tc tool from iproute2 package.
Mapped UP will be used by the HW for QoS purposes, but won't go out on the
wire.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set TSA, promised BW and PFC using IEEE 802.1qaz netlink commands.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding QoS firmware commands:
- mlx4_en_SET_PORT_PRIO2TC - set UP <=> TC
- mlx4_en_SET_PORT_SCHEDULER - set promised BW, max BW and PG number
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on HW to change schedule queue by UP, schedule
queue is fixed for a tx_ring, and UP in WQE is ignored in this aspect. This
resolves two issues with untagged traffic:
1. untagged traffic has no UP in packet which is needed for QoS. The change
above allows setting the schedule queue (and by that the UP) of such a stream.
2. BlueFlame uses the same field used by vlan tag. So forcing UP from QPC
allows using BF for untagged but prioritized traffic.
In old firmware that force UP is not supported, untagged traffic will not subject to
QoS.
Because UP is set by QP, need to always have a tx ring per UP, even if pfcrx
module paramter is false.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R8A7740 has a Gigabit Ethernet MAC. This patch supports it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original driver from chip manufacturer, but nearly full rewite.
Tested and used in production with Blackfin BF531 embedded processor.
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on original driver from chip manufacturer, but nearly full rewite.
Tested and used in production with Blackfin BF531 embedded processor.
Signed-off-by: Mike Sinkovsky <msink@permonline.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a 2-order allocation, which is too much on architectures
like ppc64, which has a 64KiB page. This particular allocation is used
for large packet fragments that may have a size of 512, 1024, 4096 or
fill the whole allocation. So, a minimum size of 16384 is good enough
and will be the same size that is used in architectures of 4KiB sized
pages.
This will avoid allocation failures that we see when the system is under
stress, but still has plenty of memory, like the one below.
This will also allow us to set the interface MTU to higher values like
9000, which was not possible on ppc64 without this patch.
Node 1 DMA: 737*64kB 37*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB 0*8192kB 0*16384kB = 51904kB
83137 total pagecache pages
0 pages in swap cache
Swap cache stats: add 0, delete 0, find 0/0
Free swap = 10420096kB
Total swap = 10420096kB
107776 pages RAM
1184 pages reserved
147343 pages shared
28152 pages non-shared
netstat: page allocation failure. order:2, mode:0x4020
Call Trace:
[c0000001a4fa3770] [c000000000012f04] .show_stack+0x74/0x1c0 (unreliable)
[c0000001a4fa3820] [c00000000016af38] .__alloc_pages_nodemask+0x618/0x930
[c0000001a4fa39a0] [c0000000001a71a0] .alloc_pages_current+0xb0/0x170
[c0000001a4fa3a40] [d00000000dcc3e00] .mlx4_en_alloc_frag+0x200/0x240 [mlx4_en]
[c0000001a4fa3b10] [d00000000dcc3f8c] .mlx4_en_complete_rx_desc+0x14c/0x250 [mlx4_en]
[c0000001a4fa3be0] [d00000000dcc4eec] .mlx4_en_process_rx_cq+0x62c/0x850 [mlx4_en]
[c0000001a4fa3d20] [d00000000dcc5150] .mlx4_en_poll_rx_cq+0x40/0x90 [mlx4_en]
[c0000001a4fa3dc0] [c0000000004e2bb8] .net_rx_action+0x178/0x450
[c0000001a4fa3eb0] [c00000000009c9b8] .__do_softirq+0x118/0x290
[c0000001a4fa3f90] [c000000000031df8] .call_do_softirq+0x14/0x24
[c000000184c3b520] [c00000000000e700] .do_softirq+0xf0/0x110
[c000000184c3b5c0] [c00000000009c6d4] .irq_exit+0xb4/0xc0
[c000000184c3b640] [c00000000000e964] .do_IRQ+0x144/0x230
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Tested-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the macro to inline function to check the arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces new team mode. It's TX port is selected by
user-set BPF hash function.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For transfering generic binary data (e.g. BPF code), introduce new
binary option type.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a specific clk_csr value is passed from the platform
this means that the CSR Clock Range selection cannot be
changed at run-time and it is fixed (as reported in the driver
documentation). Viceversa the driver will try to set the MDC
clock dynamically according to the actual clock input.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CSR Clock Range has been reworked and new macros has
been added in the platform header to allow the CSR Clock
Range selection in the GMII Address Register.
The previous work didn't add the other fields
that can be used to achieve MDC clock of frequency
higher than the IEEE 802.3 specified frequency limit
of 2.5 MHz and program a clock divider of lower value.
On such platforms, these are used indeed so this patch
adds them.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds the way to enable/disable the MAC
clock when call the open/close and resume/restore
functions.
This has been tested on ST platforms and SPEAr; thanks
to Francesco and Deepak.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Tested-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the infinite waits from the mdio read and
write interfaces. These infinite waits have been replaced by
the timeout handling. In case if a time out occurs, an error is
returned.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-works the internal GMAC DMA parameters
passed from the platform.
In the past, we only passed the pbl but, with new core,
other parameters can be passed and are mandatory on some
platforms.
New parameters are documented in stmmac.txt because this
patch has an impact for many platforms.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sanities the RX coe and adds the Type-1 Rx checksum offload engine (COE).
So the RX COE can be passed through the platform but can be fixed
at run-time in case of the core has the HW capability register.
Also to support the Type-1 Rx COE the driver must append the
HW checksum at the end of payload in case the Rx checksum
engine was used to offload the HW checksum.
This v2 version also fixes the IPC that has to be enabled and verified.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As stmmac mdio bus name prefix is hardcoded in the driver, this allows
only phys on stmmac mdio buses to connect, however stmmac should allow
phys on other mdio buses too.
This patch adds new variable phy_bus_name to plat_stmmacenet_data
struct to let the BSP decide which phy bus to be used by stmmac driver.
A typical use-case is to have generic MDIO buses like mdio-gpio on top
of stmmac.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit (bfab27a stmmac: add the experimental PCI support) the
IFF_UNICAST_FLT flag has been removed from the stmmac_mac_device_setup()
function. This patch re-adds the flag.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clears a warning message of "MDC/MDIO access timeout" which may
appear when interface is loaded due to missing clock setting before resetting
the LED, and starting periodic function too early.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a link problem on the second port of BCM57711 + BCM84823 boards due to
incorrect macro usage.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a link problem on BCM57712 + BCM8727 designs in which the TX
laser is controller by GPIO, after 1.60.xx drivers were previously loaded.
On these designs the TX_LASER is enabled by logic AND between the PHY
(through MDIO), and the GPIO. When an old driver is used, it disables the
MDIO part, hence the GPIO control had no affect de facto.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix no-LED problem when link speed is 1G on BCM57712 + BCM8727 designs, by
removing a logic error checking for a different PHY.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 578x0-SFI pre-emphasis settings per HW recommendations to achieve better
link strength.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM57810-KR link may not come up in 1G after running loopback test, so set
the relevant registers to their default values before starting KR autoneg.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 57810-KR flow-control handling link is achieved via CL37 AN.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem in which PFC frames are not honored, due to incorrect link
attributes synchronization following PMF migration, and verify PFC XON is not
stuck from previous link change.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renamed following functions:
bnad_cleanup_tx to bnad_destroy_tx
bnad_free_all_txbufs to bnad_txq_cleanup
bnad_free_txbufs to bnad_txcmpl_process
bnad_tx to bnad_tx_complete
bnad_cleanup_rx to bnad_destroy_rx
bnad_reset_rcb to bnad_rcb_cleanup
bnad_free_all_rxbufs to bnad_rxq_cleanup
bnad_cq_cmpl_init to bnad_cq_cleanup
bnad_alloc_n_post_rxbufs to bnad_rxq_post
bnad_poll_cq to bnad_cq_process
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scheduling of tasklet and keeping the interrupts enabled makes interrupt
reduntant. 20% of the Tx interrupts have nothing left to process or could not
process as Tx tasklet was running.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes busy wait in tx/rx cleanup. bnad_cb_tx_cleanup() and
bnad_cb_rx_cleanup() functions are called from irq context, and currently
they do busy wait for the in-flight transmit or the currently executing napi
polling routine to complete. To fix the issue, we create a workqueue to defer
tx & rx cleanup processing, an in the tx rx cleanup handler, we will
wait respective in flight processing to complete, before freeing the buffers.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove irrelevant code. Change to start Hearbeat failure moniter after IOC
become operational.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added NFC pause/resume logic. We only do NFC pause/resume if NFC version
is greater than 0x143 and it was halted before, otherwise we revert to
old NFC halt mechanism.
Made changes to avoid clearing off the interrupts during the initial
pll initialization.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use init semaphore to serialize execution of the "unlock IOC semaphore"
code. Added bfa_ioc_fwver_clear() function to clear the firmware header if
last firmwar boot is not from driver.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modified from original patch from Chris.
The sky2 driver has to have 8 byte alignment of receive buffer
on some chip versions. On architectures which don't support efficient
unaligned access this doesn't work very well. The solution is to
just copy all received packets which is what the driver already
does for small packets.
This allows the driver to be used on the Tilera TILEmpower-Gx, since
the tile architecture doesn't currently handle kernel unaligned accesses,
just userspace.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implemenation was buggy for slaves who use ndo_neigh_setup,
since the networking stack invokes the bonding device ndo entry (from
neigh_params_alloc) before any devices are enslaved, and the bonding
driver can't further delegate the call at that point in time. As a
result when bonding IPoIB devices, the neigh_cleanup hasn't been called.
Fix that by deferring the actual call into the slave ndo_neigh_setup
from the time the bonding neigh_setup is called.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 7d26bb103c "bonding: emit event when bonding changes MAC" didn't
take care to emit the NETDEV_CHANGEADDR event in bond_release, where bonding
actually changes the mac address (to all zeroes). As a result the neighbours
aren't deleted by the core networking code (which does so upon getting that
event).
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The platform is removed, so there are no users of this driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Probably a leftover from ancient code...
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b475d78 lacked two pairs of parenthesis, causing an overflow in the
congestion management.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM fixes from Russell King:
"Nothing too big here, just small fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: fix more fallout from 9f97da78bf (Disintegrate asm/system.h for ARM)
ARM: fix bios32.c build warning
ARM: 7337/1: ptrace: fix ptrace_read_user for !CONFIG_MMU platforms
ARM: fix missing bug.h include in arch/arm/kernel/insn.c
ARM: sa11x0: fix build errors from DMA engine API updates
This commit removes the legacy timecompare code from the igb driver and
offers a tunable PHC instead.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a source file implementing a PHC. Only the basic
clock operations have been implemented, although the hardware
would offer some ancillary functions. The code is fairly self
contained and is not yet used in the main igb driver.
Every timestamp and clock read operation must consult the overflow
counter to form a correct time value. Access to the counter is
protected by a spin lock, and the counter is implemented using the
standard cyclecounter/timecounter code.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies ixgbe_get_pcie_msix_count_generic() to support
all current HW and removes the 82598 specific function.
- change the type of ixgbe_get_pcie_msix_count_generic() to u16
- include a check to make sure the maximum allowed number of vectors
is not exceeded.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some Rx and Tx specific registers are arrays indexed by the queue number.
For clarity, specify the intended queue rather than obscuring it behind a
define.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename NAPI polling routine and a parameter with more appropriate names,
refactor a conditional branch to get rid of an unnecessary goto/label and
fix a line exceeding 80 columns.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the first phrase of a multi-line comment to the second line.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This allows the NIC to receive errored frames (bad FCS, etc)
and pass them up the stack. This can be useful when using
sniffers.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A semantic patch, fixing style issues in the bnx2x's link code.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch revises the way by which rss are configured, removing
an unnecessary module paramater and unrequired modes.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The congestion management code has migrated into a common location,
allowing all fw writes controlling mf congestion to be made in a
single function in the code. This is a semantic change.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Notice this patch includes lines with over 80 characters, as to not
break strings.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore remote-faule detection, which periodically checks for
remote-fault on the MAC layer. In case physical link appear to be
up but fault is set, it will provide a link down indication, and
when the fault is cleared, it will indicate link up again.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the bnx2x driver needed at least 2 available msix interrupt
vectors in order to use msix. This patch add the possibility of configuring
msix when only one interrupt vector is available.
Notice this patch contains lines with over 80 characters, as it keeps print
strings in a single line.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During boot-from-SAN, if msix interrupts are unavailable and inta
is requested, it is possible that inta would be disabled in the
pci bus. This patch enables inta when requested.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed uninformative debug prints, as well as two functions
which were hardly used in the code.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI is disabled during suspend and needs to be enabled on resume. Without
this the driver locks up during resume in rtl_reset_work() trying to disable
NAPI again.
Signed-off-by: Artem Savkov <artem.savkov@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 621b4d6 updated the bnx2x driver to a new FW version, but lacked
a commit to a header file with changes to the firmware's interface.
The missing interface change causes iscsi and fcoe to misbehave with the
updated firmware.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
ret = phy_write(x, y , z)
if (ret < 0)
return ret;
return 0;
As phy_write returns error code, we dont need to do not need extra check
before returning.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
ret = phy_write(x, y , z)
if (ret < 0)
return ret;
return 0;
As phy_write returns error code, we dont need to do not need extra check
before returning.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compile tested.
remove unnecessary code that matches this coccinelle pattern
ret = phy_write(x, y , z)
if (ret < 0)
return ret;
return 0;
As phy_write returns error code, we dont need to do not need extra check
before returning.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use for_each_set_bit_from to iterate over all the set bit in a memory
region.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Dmitry Kozlov <xeb@mail.ru>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes Auto Power Saving configuration in ip101a_config_init
which was broken as there is no phy register write followed after
setting IP101A_APS_ON flag.
This patch also fixes the return value of ip101a_config_init.
Without this patch ip101a_config_init returns 2 which is not an error
accroding to IS_ERR and the mac driver will continue accessing 2 as
valid pointer to phy_dev resulting in memory fault.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the adapter is closed while it is simultaneously going through a
reset, it can cause a null-pointer dereference when the two different code
paths simultaneously cleanup up the Tx/Rx resources.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up code so that changes in DCB settings
are detected only when ixgbe_dcbnl_set_all is called.
Previously, a series of 'change' commands followed by
a call to ixgbe_dcbnl_set_all() would always be handled
as a HW change - even if the net change was zero.
This patch checks for this case of no actual change and
skips going through the HW set process.
Without this fix, the link could reset and result in
a link flap.
The core change in this patch is to check for changes
in the ixgbe_copy_dcb_cfg() routine - and return
a bitmask of detected changes. The other
places where changes were detected previously can be removed.
Signed-off-by: Eric Multanen <eric.w.multanen@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This macro doesn't need a terminating ; so just remove it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the existing code, we only stop queue when the ringbuffer is full,
so the current packet has to be dropped or retried from upper layer.
This patch stops the tx queue when available ringbuffer is below
the low watermark. So the ringbuffer still has small amount of space
available for the current packet. This will reduce the overhead of
retries on sending.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For every transmitted packet, ppp_start_xmit() will stop the netdev
queue and then, if appropriate, restart it. This causes the TX softirq
to run, entirely gratuitously.
This is "only" a waste of CPU time in the normal case, but it's actively
harmful when the PPP device is a TEQL slave — the wakeup will cause the
offending device to receive the next TX packet from the TEQL queue, when
it *should* have gone to the next slave in the list. We end up seeing
large bursts of packets on just *one* slave device, rather than using
the full available bandwidth over all slaves.
This patch fixes the problem by *not* unconditionally stopping the queue
in ppp_start_xmit(). It adds a return value from ppp_xmit_process()
which indicates whether the queue should be stopped or not.
It *doesn't* remove the call to netif_wake_queue() from
ppp_xmit_process(), because other code paths (especially from
ppp_output_wakeup()) need it there and it's messy to push it out to the
other callers to do it based on the return value. So we leave it in
place — it's a no-op in the case where the queue wasn't stopped, so it's
harmless in the TX path.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sky2_test_msi() the temporarily set SW IRQ in B0 register is not reset in case
that request_irq() fails.
With this patch we only set the interrupt mask if request_irq() was successful.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
This patch corrects a bug in function sky2_open() of the Marvell Yukon 2 driver
in which the settings for PHY quick link are overwritten.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Acked-by: Stephen Hemminger <shemminger@vyattta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If port 0 of a 5717 serdes device powers down, it hides the phy from
port 1. This patch works around the problem by keeping port 0's phy
powered up.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit dae2e9f430 changed dev_alloc_skb()
to netdev_alloc_skb(), adding a dev pointer, but erroneously used "->"
instead of "." for a struct member when accessing the dev pointer.
This change fixes the build breakage.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
This commit fixes a number of issues seen with the driver:
- Improve handling of return credits to the hardware shim
- Use skb_frag_size() appropriately
- Fix driver so it works properly with netpoll for console over UDP
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros contain a hidden goto, and are thus extremely error
prone and make code hard to audit.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make CDC EEM recalculate the hard_mtu after adjusting the
hard_header_len.
Without this, usbnet adjusts the MTU down to 1494 bytes, and the host is
unable to receive standard 1500-byte frames from the device.
Tested with the Linux USB Ethernet gadget.
Cc: Oliver Neukum <oliver@neukum.name>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
SuperH has the "CONFIG_CPU_LITTLE_ENDIAN" and the "__LITTLE_ENDIAN__".
But, other architecture doesn't have them. So, this patch fixes it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There exist duplicated macro definitions in rtl8150.c, remove them.
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rionet_active is allocated from the page allocator and the allocation
order is calculated on the assumption that the page size is 4KB, so it
wastes memory on more than 4K page systems.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug appeared in a384a33bb1
("via-rhine: RHINE_WAIT_FOR macro removal). It can be noticed
during suspend/resume.
Signed-off-by: Andreas Mohr <andi@lisas.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: David Lv <DavidLv@viatech.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In parallel to the integration of lpc_eth.c, dev_hw_addr_random() has been
renamed to eth_hw_addr_random(). This patch fixes it also in the new driver
lpc_eth.c.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
Usage of /etc/modprobe.conf file was deprecated by module-init-tools and
is no longer parsed by new kmod tool. References to this file are
replaced in Documentation, comments and Kconfig according to the
context.
There are also some references to the old /etc/modules.conf from 2.4
kernels that are being removed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent merge of the sa11x0 code into mainline had silent conflicts
with further development of the DMA engine API, leading to build errors
and warnings:
drivers/net/irda/sa1100_ir.c: In function 'sa1100_irda_dma_start':
drivers/net/irda/sa1100_ir.c:151: error: too few arguments to function 'chan->device->device_prep_slave_sg'
drivers/dma/sa11x0-dma.c: In function 'sa11x0_dma_probe':
drivers/dma/sa11x0-dma.c:950: warning: assignment from incompatible pointer type
Fix these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
When a bonding device is configured with fail_over_mac=active,
we expect to see the MAC address of the new active slave as the source MAC
address after failover. But we see that the source MAC address is the MAC
address of previous active slave.
Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order
to let arp_netdev_event flush neighbour cache and route cache.
How to reproduce this bug ?
-----------hostB----------------
hostA ----- switch ---|-- eth0--bond0(192.168.100.2/24)|
(192.168.100.1/24 \--|-- eth1-/ |
--------------------------------
1 on hostB,
modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000
num_grat_arp=1
ifconfig bond0 192.168.100.2/24 up
ifenslave bond0 eth0
ifenslave bond0 eth1
then eth0 is the active slave, and MAC of bond0 is MAC of eth0.
2 on hostA, ping 192.168.100.2
3 on hostB,
tcpdump -i bond0 -p icmp -XXX
you will see bond0 uses MAC of eth0 as source MAC in icmp reply.
4 on hostB,
ifconfig eth0 down
tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3)
you will see first bond0 uses MAC of eth1 as source MAC in icmp
reply, then it will use MAC of eth0 as source MAC.
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPC8569 Rev2.0 has the correct SNUM table as QE Reference Manual, we
must follow it.
However the Rev1.0 silicon need the old SNUM table as workaround due to
Rev1.0 silicon SNUM erratum.
So, we support both snum table, and choose the one FDT tell us.
And u-boot will fixup FDT according to SPRN_SVR.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Pull a few more things for powerpc by Benjamin Herrenschmidt:
- Anton's did some recent improvements to EPOW event reporting on
pSeries (power supply failures and such). The patches are self
contained enough and replace really nasty code so I felt it should
still go in
- I did the vio driver registration change Greg requested, I don't see
the point of leaving that til the next merge window
- The remaining EEH changes I said were still pending to get rid of the
EEH references from the generic struct device_node
- A few more iSeries removal bits
- A perf bug fix on 970
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: Fix instruction address sampling on 970 and Power4
powerpc+sparc/vio: Modernize driver registration
powerpc: Random little legacy iSeries removal tidy ups
powerpc: Remove NO_IRQ_IGNORE
powerpc/pseries: Cut down on enthusiastic use of defines in RAS code
powerpc/pseries: Clean up ras_error_interrupt code
powerpc/pseries: Remove RTAS_POWERMGM_EVENTS
powerpc/pseries: Use rtas_get_sensor in RAS code
powerpc/pseries: Parse and handle EPOW interrupts
powerpc: Make function that parses RTAS error logs global
powerpc/eeh: Retrieve PHB from global list
powerpc/eeh: Remove eeh information from pci_dn
powerpc/eeh: Remove eeh device from OF node
The commit "ath9k: Remove aggregation flags" changed how
nodes were being initialized. Use the HW HT cap bits
to initialize/de-initialize nodes, else we would be
accessing an uninitialized entry during a suspend/resume cycle,
resulting in a panic.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With flag 'GFP_ATOMIC', probability of allocation failure is more.
Add error handling after kmalloc() call to avoid null dereference.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
Disintegrate asm/system.h for ARM.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Russell King <linux@arm.linux.org.uk>
cc: linux-arm-kernel@lists.infradead.org
While it is desirable to rate limit certain messages, it is not
desirable to rate limit the incrementing of counters associated
with those messages.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version number to better match version of out of tree
driver that has similar functionality.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This was pointed out to me by Xiaojun Zhang on Source Forge.
CC: Xiaojun Zhang <zhangxiaojun@sourceforge.net>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Dan Carpenter noticed that ixgbevf initial default was different than
the rest. But the problem is broader than that, only one Intel driver (ixgb)
was doing it almost right.
The convention for default debug level should be consistent among
Intel drivers and follow established convention.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now skb_add_rx_frag() has a truesize parameter, we can fix cdc-phonet to
properly account truesize of each fragment : a full page.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HZ is more likely to be 1000 these days.
timer handlers are run from softirq, no need to disable bh
skb priority 1 is TC_PRIO_FILLER
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the bug that may prevent from mac to be configured,
while there is an empty slot for it.
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flow in which the bnx2x driver starts after a previous driver
has been terminated in an 'unclean' manner has several bugs and
FW risks, which makes it possible for the driver to fail after
boot-from-SAN or kdump.
This patch contains a revised flow which performs a safer
initialization, solving the possible crash scenarios.
Notice this patch contains lines with over 80 characters, as it
keeps print-strings in a single line.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added Vendor/Device Id of Motorola Rokr E6 (22b8:6027) so it can be
recognized by the "zaurus" USBNet driver.
Applies to Linux 3.2.13 and 2.6.39.4.
Signed-off-by: Guan Xin <guanx.bac@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add define of SH7734 register and sh_eth_reset_hw_crc function.
V3: Rebase net/HEAD.
V2: Do not split line of #if defined.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way the USB variant of the driver uses usb_make_path in order to
provide bus-info compatible to other USB drivers (like e.g. asix.c).
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This happened on a machine with a custom hotplug script calling nameif,
probably due to slow firmware loading. At the time nameif uses ethtool
to gather interface information, i2400m->fw_name is zero and so a null
pointer dereference occurs from within i2400m_get_drvinfo().
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a regression introduced by commit "e1000: do vlan
cleanup (799d531)".
Apparently some e1000 chips (not mine) are sensitive about the order of
setting vlan filter and vlan stripping/inserting functionality. So this
patch changes the order so it's the same as before vlan cleanup.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
This makes vio_register_driver() get the module owner & name at compile
time like PCI drivers do, and adds a name pointer directly in struct
vio_driver to avoid having to explicitly initialize the embedded
struct device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Name string overrun fix in gianfar driver from Joe Perches.
2) VHOST bug fixes from Michael S. Tsirkin and Nadav Har'El
3) Fix dependencies on xt_LOG netfilter module, from Pablo Neira Ayuso.
4) Fix RCU locking in xt_CT, also from Pablo Neira Ayuso.
5) Add a parameter to skb_add_rx_frag() so we can fix the truesize
adjustments in the drivers that use it. The individual drivers
aren't fixed by this commit, but will be dealt with using follow-on
commits. From Eric Dumazet.
6) Add some device IDs to qmi_wwan driver, from Andrew Bird.
7) Fix a potential rcu_read_lock() imbalancein rt6_fill_node(). From
Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: fix a potential rcu_read_lock() imbalance in rt6_fill_node()
net: add a truesize parameter to skb_add_rx_frag()
gianfar: Fix possible overrun and simplify interrupt name field creation
USB: qmi_wwan: Add ZTE (Vodafone) K3570-Z and K3571-Z net interfaces
USB: option: Ignore ZTE (Vodafone) K3570/71 net interfaces
USB: qmi_wwan: Add ZTE (Vodafone) K3565-Z and K4505-Z net interfaces
qlcnic: Bug fix for LRO
netfilter: nf_conntrack: permanently attach timeout policy to conntrack
netfilter: xt_CT: fix assignation of the generic protocol tracker
netfilter: xt_CT: missing rcu_read_lock section in timeout assignment
netfilter: cttimeout: fix dependency with l4protocol conntrack module
netfilter: xt_LOG: use CONFIG_IP6_NF_IPTABLES instead of CONFIG_IPV6
vhost: fix release path lockdep checks
vhost: don't forget to schedule()
tools/virtio: stub out strong barriers
tools/virtio: add linux/hrtimer.h stub
tools/virtio: add linux/module.h stub
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
As of bb0eb217, MTD_FAIL_ADDR_UNKNOWN should be used to indicate mtd
erase failure not specific to any particular block.
Use MTD_FAIL_ADDR_UNKNOWN instead of 0xffffffff when setting
'erase->fail_addr' in 'efx_mtd_erase()'.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch renames all MTD functions by adding a "_" prefix:
mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In https://bugzilla.redhat.com/show_bug.cgi?id=770207, slowdowns of driver
rtl8192ce are reported. One fix (commit a9b89e2) has already been applied,
and it helped, but the maximum RX speed would still drop to 1 Mbps. As in
the previous fix, the initial gain was determined to be the problem; however,
the problem arises from a setting of the gain when scans are started.
Driver rtl8192de also has the same code structure - this one is fixed as well.
Reported-and-Tested-by: Ivan Pesin <ivan.pesin@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another good catch from Jakub Kicinski. This patch fixes my
recent commit: ed61e2b020
"rt2x00: rt2800usb: rework txdone code"
We should reread status register only when nobody else start already
reading status i.e. test_and_set_bit(TX_STATUS_READING, flags) return 0.
Reported-by: Jakub Kicinski <moorray@wp.pl>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is fix for my current commit
ed61e2b020
"rt2x00: rt2800usb: rework txdone code"
We should schedule txdone work on timeout, otherwise if newer get
tx status from hardware, we will never report tx status to mac80211
and eventually never wakeup tx queue.
Reported-by: Jakub Kicinski <moorray@wp.pl>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 0d95521ea7 (ath9k: use split rx buffers to get rid of order-1 skb
allocations) added in memory leak in error path.
sc->rx.frag should be cleared after the pskb_expand_head() call, or else
we jump to requeue_drop_frag and leak an skb.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we have downlink traffic alone and the station is going thru
bgscan, the client is out of operating channel for around 1000ms which
is too long. The mac80211 decides when to switch back to oper channel
based on tx queue, bad latency and listen time. As the station does not
have tx traffic, the bgscan can easily affect downlink throughput. By
reducing the listen time, it helps the associated AP to retain the
downstream rate.
Cc: Paul Stewart <pstew@google.com>
Tested-by: Gary Morain <gmorain@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current commit 0775f9f90c
"mac80211: remove spurious BSSID change flag" exposed bug on iwlegacy,
that we do not set BSSID address correctly and then device was not able
to receive frames after successful associate.
On the way fix scan canceling comment. Apparently ->post_associate()
do cancel scan itself, but scan cancel on BSS_CHANGED_BSSID is needed.
I'm not sure why, but when I removed it, I had frequent auth failures:
wlan4: send auth to 54:e6:fc:98:63:fe (try 1/3)
wlan4: send auth to 54:e6:fc:98:63:fe (try 2/3)
wlan4: send auth to 54:e6:fc:98:63:fe (try 3/3)
wlan4: authentication with 54:e6:fc:98:63:fe timed out
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the maximum noise floor limit is set as too high (-60dB). The
assumption of having a higher threshold limit is that it would help
de-sensitize the receiver (reduce phy errors) from continuous
interference. But when we have a bursty interference where there are
collisions and then free air time and if the receiver is desensitized too
much, it will miss the normal packets too. Lets make use of chips
specific min, nom and max limits always. This patch helps to improve the
connection stability in congested networks.
Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@google.com>
Tested-by: Gary Morain <gmorain@google.com>
Signed-off-by: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This il->vif is dereferenced in different part of iwlegacy code, so do
not nullify it. This should fix random crashes observed in companion
with microcode errors i.e. crash in il3945_config_ap().
Additionally this should address also
WARNING: at drivers/net/wireless/iwlegacy/common.c:4656 il_mac_remove_interface
at least one of the possible reasons of that warning.
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skb_add_rx_frag() API is misleading.
Network skbs built with this helper can use uncharged kernel memory and
eventually stress/crash machine in OOM.
Add a 'truesize' parameter and then fix drivers in followup patches.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Space allocated for int_name_<foo> is insufficient for
maximal device name, expand it.
Code to create int_name_<foo> is obscure, simplify it
by using sprintf.
Found by looking for unnecessary \ line continuations.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the beginnings of an OSS method to use the network
interfaces on these USB broadband modems, add the ZTE manufactured
Vodafone items to the whitelist
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the beginnings of an OSS method to use the network
interfaces on these USB broadband modems, add the ZTE manufactured
Vodafone items to the whitelist
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Add fast-EOI acking of interrupts (clear a bit instead of hypercall)
And bug-fixes:
* Fix CPU bring-up code missing a call to notify other subsystems.
* Fix reading /sys/hypervisor even if PVonHVM drivers are not loaded.
* In Xen ACPI processor driver: remove too verbose WARN messages, fix up
the Kconfig dependency to be a module by default, and add dependency on
CPU_FREQ.
* Disable CPU frequency drivers from loading when booting under Xen
(as we want the Xen ACPI processor to be used instead).
* Cleanups in tmem code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPbc3DAAoJEFjIrFwIi8fJTQkIAMnH2fPhcHAb4mNaz+3gdmsZ
Flo6V1gMBcO8xKZlUkFgKKPYoOm7lLmvoceXLVSH5oOKSnSJo1zSinzKmcdJQo/D
kPo4/EguNwtzcAcQh2dmT6/IM9O3ihMKUli7Oajif9PLCFFFqTaG3Y3YNBo/rxTY
D3HAnJrIfmIyG0NpLnaFCWhCzUvcB4M7ysutECqcF8l5gnbHxRVeCKD0blM+n9GH
Wyum00dQCwo6h6wTduhPOAxHAM4rncyR3heOB2vDxq9YJHSUhhcva5QCgQ+tdUVt
6U2TQT1L2Px8iXXzr2w9YBpepOVajZReoKhajLjJ5VbkpBZFz5dVNfJ8LpF8RV8=
=z8IB
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.4-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull more xen updates from Konrad Rzeszutek Wilk:
"One tiny feature that accidentally got lost in the initial git pull:
* Add fast-EOI acking of interrupts (clear a bit instead of
hypercall)
And bug-fixes:
* Fix CPU bring-up code missing a call to notify other subsystems.
* Fix reading /sys/hypervisor even if PVonHVM drivers are not loaded.
* In Xen ACPI processor driver: remove too verbose WARN messages, fix
up the Kconfig dependency to be a module by default, and add
dependency on CPU_FREQ.
* Disable CPU frequency drivers from loading when booting under Xen
(as we want the Xen ACPI processor to be used instead).
* Cleanups in tmem code."
* tag 'stable/for-linus-3.4-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/acpi: Fix Kconfig dependency on CPU_FREQ
xen: initialize platform-pci even if xen_emul_unplug=never
xen/smp: Fix bringup bug in AP code.
xen/acpi: Remove the WARN's as they just create noise.
xen/tmem: cleanup
xen: support pirq_eoi_map
xen/acpi-processor: Do not depend on CPU frequency scaling drivers.
xen/cpufreq: Disable the cpu frequency scaling drivers from loading.
provide disable_cpufreq() function to disable the API.
- After FW reset, IP addresses need to be reprogrammed to FW for LRO to work. This
was not happening in context reset path. Fixed it here.
- Updated driver version to 5.0.27
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) L2TP doesn't get autoloaded when you try to open an L2TP socket due
to a missing module alias, fix from Benjamin LaHaise.
2) Netlabel and RDS should propagate gfp flags given to them by
callers, fixes from Dan Carpeneter.
3) Recursive locking fix in usbnet wasn't bulletproof and can result in
objects going away mid-flight due to races, fix from Ming Lei.
4) Fix up some confusion about a bool module parameter in netfilter's
iptable_filter and ip6table_filter, from Rusty Russell.
5) If SKB recycling is used via napi_reuse_skb() we end up with
different amounts of headroom reserved than we had at the original
SKB allocation. Fix from Eric Dumazet.
6) Fix races in TG3 driver ring refilling, from Michael Chan.
7) We have callbacks for IPSEC replay notifiers, but some call sites
were not using the ops method and instead were calling one of the
implementations directly. Oops. Fix from Steffen Klassert.
8) Fix IP address validation properly in the bonding driver, the
previous fix only works with netlink where the subnet mask and IP
address are changed in one atomic operation. When 'ifconfig' ioctls
are used the IP address and the subnet mask are changed in two
distinct operations. Fix from Andy Gospodarek.
9) Provide a sky2 module operation to work around power management
issues with some BIOSes. From Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
usbnet: consider device busy at each recieved packet
bonding: remove entries for master_ip and vlan_ip and query devices instead
netfilter: remove forward module param confusion.
usbnet: don't clear urb->dev in tx_complete
usbnet: increase URB reference count before usb_unlink_urb
xfrm: Access the replay notify functions via the registered callbacks
xfrm: Remove unused xfrm_state from xfrm_state_check_space
RDS: use gfp flags from caller in conn_alloc()
netlabel: use GFP flags from caller instead of GFP_ATOMIC
l2tp: enable automatic module loading for l2tp_ppp
cnic: Fix parity error code conflict
tg3: Fix RSS ring refill race condition
sky2: override for PCI legacy power management
net: fix napi_reuse_skb() skb reserve
usbnet should centrally handle busy reporting in the rx path
so subdrivers need not worry. This hurts use cases which do
rx only or predominantly.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch aimed to resolve an issue where secondary, tertiary,
etc. addresses added to bond interfaces could overwrite the
bond->master_ip and vlan_ip values.
commit 917fbdb32f
Author: Henrik Saavedra Persson <henrik.e.persson@ericsson.com>
Date: Wed Nov 23 23:37:15 2011 +0000
bonding: only use primary address for ARP
That patch was good because it prevented bonds using ARP monitoring from
sending frames with an invalid source IP address. Unfortunately, it
didn't always work as expected.
When using an ioctl (like ifconfig does) to set the IP address and
netmask, 2 separate ioctls are actually called to set the IP and netmask
if the mask chosen doesn't match the standard mask for that class of
address. The first ioctl did not have a mask that matched the one in
the primary address and would still cause the device address to be
overwritten. The second ioctl that was called to set the mask would
then detect as secondary and ignored, but the damage was already done.
This was not an issue when using an application that used netlink
sockets as the setting of IP and netmask came down at once. The
inconsistent behavior between those two interfaces was something that
needed to be resolved.
While I was thinking about how I wanted to resolve this, Ralf Zeidler
came with a patch that resolved this on a RHEL kernel by keeping a full
shadow of the entries in dev->ifa_list for the bonding device and vlan
devices in the bonding driver. I didn't like the duplication of the
list as I want to see the 'bonding' struct and code shrink rather than
grow, but liked the general idea.
As the Subject indicates this patch drops the master_ip and vlan_ip
elements from the 'bonding' and 'vlan_entry' structs, respectively.
This can be done because a device's address-list is now traversed to
determine the optimal source IP address for ARP requests and for checks
to see if the bonding device has a particular IP address. This code
could have all be contained inside the bonding driver, but it made more
sense to me to EXPORT and call inet_confirm_addr since it did exactly
what was needed.
I tested this and a backported patch and everything works as expected.
Ralf also helped with verification of the backported patch.
Thanks to Ralf for all his help on this.
v2: Whitespace and organizational changes based on suggestions from Jay
Vosburgh and Dave Miller.
v3: Fixup incorrect usage of rcu_read_unlock based on Dave Miller's
suggestion.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Ralf Zeidler <ralf.zeidler@nsn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
URB unlinking is always racing with its completion and tx_complete
may be called before or during running usb_unlink_urb, so tx_complete
must not clear urb->dev since it will be used in unlink path,
otherwise invalid memory accesses or usb device leak may be caused
inside usb_unlink_urb.
Cc: stable@kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4231d47e6fe69f061f96c98c30eaf9fb4c14b96d(net/usbnet: avoid
recursive locking in usbnet_stop()) fixes the recursive locking
problem by releasing the skb queue lock, but it makes usb_unlink_urb
racing with defer_bh, and the URB to being unlinked may be freed before
or during calling usb_unlink_urb, so use-after-free problem may be
triggerd inside usb_unlink_urb.
The patch fixes the use-after-free problem by increasing URB
reference count with skb queue lock held before calling
usb_unlink_urb, so the URB won't be freed until return from
usb_unlink_urb.
Cc: stable@kernel.org
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oliver@neukum.org>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When xen_emul_unplug=never is specified on kernel command line
reading files from /sys/hypervisor is broken (returns -EBUSY).
It is caused by xen_bus dependency on platform-pci and
platform-pci isn't initialized when xen_emul_unplug=never is
specified.
Fix it by allowing platform-pci to ignore xen_emul_unplug=never,
and do not intialize xen_[blk|net]front instead.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The recently added parity error handling used an error code that was
already defined for a different error. This could lead to bnx2x
firmware assert. We need to fix this with new error codes that are
defined for parity error only.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RSS feature in tg3 hardware has only one rx producer ring for all
RSS rings. NAPI vector 1 is special and handles the refilling of the
rx producer ring on behalf of all RSS rings. There is a race condition
between these RSS NAPIs and the NAPI[1]. If NAPI[1] finishes checking
for refill and then another RSS ring empties the rx producer ring
before NAPI[1] exits NAPI, the chip will be completely out of SKBs in
the rx producer ring.
We fix this by adding a flag tp->rx_refill and rely on napi_schedule()/
napi_complete() to help synchronize it to close the race condition.
Update driver version to 3.123.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some BIOS's don't setup power management correctly (what else is
new) and don't allow use of PCI Express power control. Add a special
exception module parameter to allow working around this issue.
Based on slightly different patch by Knut Petersen.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs pile 1 from Al Viro:
"This is _not_ all; in particular, Miklos' and Jan's stuff is not there
yet."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (64 commits)
ext4: initialization of ext4_li_mtx needs to be done earlier
debugfs-related mode_t whack-a-mole
hfsplus: add an ioctl to bless files
hfsplus: change finder_info to u32
hfsplus: initialise userflags
qnx4: new helper - try_extent()
qnx4: get rid of qnx4_bread/qnx4_getblk
take removal of PF_FORKNOEXEC to flush_old_exec()
trim includes in inode.c
um: uml_dup_mmap() relies on ->mmap_sem being held, but activate_mm() doesn't hold it
um: embed ->stub_pages[] into mmu_context
gadgetfs: list_for_each_safe() misuse
ocfs2: fix leaks on failure exits in module_init
ecryptfs: make register_filesystem() the last potential failure exit
ntfs: forgets to unregister sysctls on register_filesystem() failure
logfs: missing cleanup on register_filesystem() failure
jfs: mising cleanup on register_filesystem() failure
make configfs_pin_fs() return root dentry on success
configfs: configfs_create_dir() has parent dentry in dentry->d_parent
configfs: sanitize configfs_create()
...
Pull security subsystem updates for 3.4 from James Morris:
"The main addition here is the new Yama security module from Kees Cook,
which was discussed at the Linux Security Summit last year. Its
purpose is to collect miscellaneous DAC security enhancements in one
place. This also marks a departure in policy for LSM modules, which
were previously limited to being standalone access control systems.
Chromium OS is using Yama, and I believe there are plans for Ubuntu,
at least.
This patchset also includes maintenance updates for AppArmor, TOMOYO
and others."
Fix trivial conflict in <net/sock.h> due to the jumo_label->static_key
rename.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (38 commits)
AppArmor: Fix location of const qualifier on generated string tables
TOMOYO: Return error if fails to delete a domain
AppArmor: add const qualifiers to string arrays
AppArmor: Add ability to load extended policy
TOMOYO: Return appropriate value to poll().
AppArmor: Move path failure information into aa_get_name and rename
AppArmor: Update dfa matching routines.
AppArmor: Minor cleanup of d_namespace_path to consolidate error handling
AppArmor: Retrieve the dentry_path for error reporting when path lookup fails
AppArmor: Add const qualifiers to generated string tables
AppArmor: Fix oops in policy unpack auditing
AppArmor: Fix error returned when a path lookup is disconnected
KEYS: testing wrong bit for KEY_FLAG_REVOKED
TOMOYO: Fix mount flags checking order.
security: fix ima kconfig warning
AppArmor: Fix the error case for chroot relative path name lookup
AppArmor: fix mapping of META_READ to audit and quiet flags
AppArmor: Fix underflow in xindex calculation
AppArmor: Fix dropping of allowed operations that are force audited
AppArmor: Add mising end of structure test to caps unpacking
...
stands out; by patch count lots of fixes to the mlx4 driver plus some
cleanups and fixes to the core and other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DbLx
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes for the 3.4 merge window from Roland Dreier:
"Nothing big really stands out; by patch count lots of fixes to the
mlx4 driver plus some cleanups and fixes to the core and other
drivers."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (28 commits)
mlx4_core: Scale size of MTT table with system RAM
mlx4_core: Allow dynamic MTU configuration for IB ports
IB/mlx4: Fix info returned when querying IBoE ports
IB/mlx4: Fix possible missed completion event
mlx4_core: Report thermal error events
mlx4_core: Fix one more static exported function
IB: Change CQE "csum_ok" field to a bit flag
RDMA/iwcm: Reject connect requests if cmid is not in LISTEN state
RDMA/cxgb3: Don't pass irq flags to flush_qp()
mlx4_core: Get rid of redundant ext_port_cap flags
RDMA/ucma: Fix AB-BA deadlock
IB/ehca: Fix ilog2() compile failure
IB: Use central enum for speed instead of hard-coded values
IB/iser: Post initial receive buffers before sending the final login request
IB/iser: Free IB connection resources in the proper place
IB/srp: Consolidate repetitive sysfs code
IB/srp: Use pr_fmt() and pr_err()/pr_warn()
IB/core: Fix SDR rates in sysfs
mlx4: Enforce device max FMR maps in FMR alloc
IB/mlx4: Set bad_wr for invalid send opcode
...
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPZ1yiAAoJEEFnBt12D9kB4yIQAJvCfTPL65sCYVD6i9RnVHtR
ahwddtd0AtT+UYLU8Xg2fZgVi6cmupDGnqkBixzZD3xxSTERqm7Snqa0ugklfeAi
B6Zqf/K17H5hJNaoQ3fkNauow8m7ZYOeEH2vVUvkb3woWS9Wm7OGd+BvcIBgYSGe
Aaoumhu7kDxFkii0qz3x/+kvsb6DRp2HtSPWj+APL/kNjdiO4JBOihtcc/lX6d47
bsZLiEMzHUFV4ApJNwqmfDnf54oMrHmrRJxgQHIMjeJC5or9I3Do8wDGe/aTF5xO
5GVpxCQsTlJMjTBWlAFtpTwCJB6y76EHQrHc7WzLlq8OJSsxApOke8M0BzXFrfMy
CU7UUpTvNZTLpZibLCEQKemv1+oNOkfFylsHxfek2MCqx0W6W4FHEGV3qE/GtgV9
+vurA9hNNp7VM0FGRGigcUr3woYdHLdEVQrlnL7Z9AgBu1W44MZLaai7iRVZOeCT
ZQ9++v2PJJ8vHT8kdkgTdiRpnEhmv84MX/GBT7ilWFEMIVeT5zhGkIBojzNgyzGc
7cvermmM0P8h+unkDgmzmSbDxo0PboqVKeoO71AOBhA6MmR9iom7XkuNdHhoOwy2
4A5xT1srbhJDbuv15BBREBV24TywpZ4a1+4nwQT4L1fXe+HfCxeEWexGcKQMRcIt
dAelOHTQ+ZGkOKvXeW05
=ruGA
-----END PGP SIGNATURE-----
Merge tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull irq_domain support for all architectures from Grant Likely:
"Generialize powerpc's irq_host as irq_domain
This branch takes the PowerPC irq_host infrastructure (reverse mapping
from Linux IRQ numbers to hardware irq numbering), generalizes it,
renames it to irq_domain, and makes it available to all architectures.
Originally the plan has been to create an all-new irq_domain
implementation which addresses some of the powerpc shortcomings such
as not handling 1:1 mappings well, but doing that proved to be far
more difficult and invasive than generalizing the working code and
refactoring it in-place. So, this branch rips out the 'new'
irq_domain and replaces it with the modified powerpc version (in a
fully bisectable way of course). It converts all users over to the
new API and makes irq_domain selectable on any architecture.
No architecture is forced to enable irq_domain, but the infrastructure
is required for doing OpenFirmware style irq translations. It will
even work on SPARC even though SPARC has it's own mechanism for
translating irqs at boot time. MIPS, microblaze, embedded x86 and c6x
are converted too.
The resulting irq_domain code is probably still too verbose and can be
optimized more, but that can be done incrementally and is a task for
follow-on patches."
* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6: (31 commits)
dt: fix twl4030 for non-dt compile on x86
mfd: twl-core: Add IRQ_DOMAIN dependency
devicetree: Add empty of_platform_populate() for !CONFIG_OF_ADDRESS (sparc)
irq_domain: Centralize definition of irq_dispose_mapping()
irq_domain/mips: Allow irq_domain on MIPS
irq_domain/x86: Convert x86 (embedded) to use common irq_domain
ppc-6xx: fix build failure in flipper-pic.c and hlwd-pic.c
irq_domain/microblaze: Convert microblaze to use irq_domains
irq_domain/powerpc: Replace custom xlate functions with library functions
irq_domain/powerpc: constify irq_domain_ops
irq_domain/c6x: Use library of xlate functions
irq_domain/c6x: constify irq_domain structures
irq_domain/c6x: Convert c6x to use generic irq_domain support.
irq_domain: constify irq_domain_ops
irq_domain: Create common xlate functions that device drivers can use
irq_domain: Remove irq_domain_add_simple()
irq_domain: Remove 'new' irq_domain in favour of the ppc one
mfd: twl-core.c: Fix the number of interrupts managed by twl4030
of/address: add empty static inlines for !CONFIG_OF
irq_domain: Add support for base irq and hwirq in legacy mappings
...
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
Conflicts:
arch/arm/mach-lpc32xx/clock.c
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The conflicts with pxa are non-obvious, we have multiple branches
adding and removing the same clock settings. According to
Haojian Zhuang, removing the sa1100 rtc dummy clock is the correct
fix here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and other
various minor things.
There are some patches touching arch code, but they have all been acked
by the various arch maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9njL8ACgkQMUfUDdst+ylQ9wCfbBOnIT01lGOorkaE9pom0hhk
HfMAoKq1xzCR2B+OS3UMyUQffk+Ri9Ri
=KIQ2
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB merge for 3.4-rc1 from Greg KH:
"Here's the big USB merge for the 3.4-rc1 merge window.
Lots of gadget driver reworks here, driver updates, xhci changes, some
new drivers added, usb-serial core reworking to fix some bugs, and
other various minor things.
There are some patches touching arch code, but they have all been
acked by the various arch maintainers."
* tag 'usb-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (302 commits)
net: qmi_wwan: add support for ZTE MF820D
USB: option: add ZTE MF820D
usb: gadget: f_fs: Remove lock is held before freeing checks
USB: option: make interface blacklist work again
usb/ub: deprecate & schedule for removal the "Low Performance USB Block" driver
USB: ohci-pxa27x: add clk_prepare/clk_unprepare calls
USB: use generic platform driver on ath79
USB: EHCI: Add a generic platform device driver
USB: OHCI: Add a generic platform device driver
USB: ftdi_sio: new PID: LUMEL PD12
USB: ftdi_sio: add support for FT-X series devices
USB: serial: mos7840: Fixed MCS7820 device attach problem
usb: Don't make USB_ARCH_HAS_{XHCI,OHCI,EHCI} depend on USB_SUPPORT.
usb gadget: fix a section mismatch when compiling g_ffs with CONFIG_USB_FUNCTIONFS_ETH
USB: ohci-nxp: Remove i2c_write(), use smbus
USB: ohci-nxp: Support for LPC32xx
USB: ohci-nxp: Rename symbols from pnx4008 to nxp
USB: OHCI-HCD: Rename ohci-pnx4008 to ohci-nxp
usb: gadget: Kconfig: fix typo for 'different'
usb: dwc3: pci: fix another failure path in dwc3_pci_probe()
...
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty layer,
and a number of patches from Alan to help try to wrestle the vt layer
into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9nihQACgkQMUfUDdst+ylXTQCdFuwVuZgjCts+xDVa1jX2ac84
UogAn3Wr+P7NYFN6gvaGm52KbGbZs405
=2b/l
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/serial patches from Greg KH:
"tty and serial merge for 3.4-rc1
Here's the big serial and tty merge for the 3.4-rc1 tree.
There's loads of fixes and reworks in here from Jiri for the tty
layer, and a number of patches from Alan to help try to wrestle the vt
layer into a sane model.
Other than that, lots of driver updates and fixes, and other minor
stuff, all detailed in the shortlog."
* tag 'tty-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (132 commits)
serial: pxa: add clk_prepare/clk_unprepare calls
TTY: Wrong unicode value copied in con_set_unimap()
serial: PL011: clear pending interrupts
serial: bfin-uart: Don't access tty circular buffer in TX DMA interrupt after it is reset.
vt: NULL dereference in vt_do_kdsk_ioctl()
tty: serial: vt8500: fix annotations for probe/remove
serial: remove back and forth conversions in serial_out_sync
serial: use serial_port_in/out vs serial_in/out in 8250
serial: introduce generic port in/out helpers
serial: reduce number of indirections in 8250 code
serial: delete useless void casts in 8250.c
serial: make 8250's serial_in shareable to other drivers.
serial: delete last unused traces of pausing I/O in 8250
pch_uart: Add module parameter descriptions
pch_uart: Use existing default_baud in setup_console
pch_uart: Add user_uartclk parameter
pch_uart: Add Fish River Island II uart clock quirks
pch_uart: Use uartclk instead of base_baud
mpc5200b/uart: select more tolerant uart prescaler on low baudrates
tty: moxa: fix bit test in moxa_start()
...
Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink breakage
reverted), dynamic debugging updates, w1 drivers, hyperv driver updates,
and a variety of other bits and pieces, full information in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9neCsACgkQMUfUDdst+ylyQwCfY2eizvzw5HhjQs8gOiBRDADe
yrgAnj1Zan2QkoCnQIFJNAoxqNX9yAhd
=biH6
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches for 3.4-rc1 from Greg KH:
"Here's the big driver core merge for 3.4-rc1.
Lots of various things here, sysfs fixes/tweaks (with the nlink
breakage reverted), dynamic debugging updates, w1 drivers, hyperv
driver updates, and a variety of other bits and pieces, full
information in the shortlog."
* tag 'driver-core-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (78 commits)
Tools: hv: Support enumeration from all the pools
Tools: hv: Fully support the new KVP verbs in the user level daemon
Drivers: hv: Support the newly introduced KVP messages in the driver
Drivers: hv: Add new message types to enhance KVP
regulator: Support driver probe deferral
Revert "sysfs: Kill nlink counting."
uevent: send events in correct order according to seqnum (v3)
driver core: minor comment formatting cleanups
driver core: move the deferred probe pointer into the private area
drivercore: Add driver probe deferral mechanism
DS2781 Maxim Stand-Alone Fuel Gauge battery and w1 slave drivers
w1_bq27000: Only one thread can access the bq27000 at a time.
w1_bq27000 - remove w1_bq27000_write
w1_bq27000: remove unnecessary NULL test.
sysfs: Fix memory leak in sysfs_sd_setsecdata().
intel_idle: Revert change of auto_demotion_disable_flags for Nehalem
w1: Fix w1_bq27000
driver-core: documentation: fix up Greg's email address
powernow-k6: Really enable auto-loading
powernow-k7: Fix CPU family number
...
Fixes:
drivers/built-in.o: In function `qmi_wwan_bind_shared':
qmi_wwan.c:(.text+0x25b686): undefined reference to `usb_cdc_wdm_register'
make[1]: *** [.tmp_vmlinux1] Error 1
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for TI's CPSW driver.
The three port switch gigabit ethernet subsystem provides ethernet packet
communication and can be configured as an ethernet switch. Supports
10/100/1000 Mbps.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPSW ethernet switch has a built-in address lookup engine. This patch adds
the code necessary for programming this module.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
