Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
Added one additional parameter to thermal_zone_device_update() to provide
caller with an optional capability to specify reason.
Currently this event is used by user space governor to trigger different
processing based on event code. Also it saves an additional call to read
temperature when the event is received.
The following events are cuurently defined:
- Unspecified event
- New temperature sample
- Trip point violated
- Trip point changed
- thermal device up and down
- thermal device power capability changed
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_thermal_zone_of_sensor_register() case doesn't need to call
thermal_zone_device_unregister().
Otherwise, rcar-thermal can't register thermal zone again after rebind.
This patch fixes it.
Signed-off-by: Bui Duc Phuc <bd-phuc@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
rcar-thermal is supporting both thermal_zone_of_sensor_register() and
thermal_zone_device_register(). But thermal_zone_of_sensor_register()
doesn't enable hwmon as default.
This patch enables it to keep compatibility
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
In case thermal_zone_xxx_register() returns an error, priv->zone
isn't NULL any more, but contains the error code.
This is passed to thermal_zone_device_unregister(), then. This checks
for priv->zone being NULL, but the error code is != NULL. So it works
with the error code as a pointer. Crashing immediately.
To fix this, reset priv->zone to NULL before entering
rcar_gen3_thermal_remove().
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch enables to use thermal-zone on DT if it was calles as
"renesas,rcar-thermal-gen2".
Previous style (= non thermal-zone) is still supported by
"renesas,rcar-thermal" to keep compatibility for "git bisect".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Current rcar thermal driver sometimes checks irq possibility when it
calls rcar_thermal_irq_enable/disable(), but sometimes not.
This patch checks it inside rcar_thermal_irq_enable/disable().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Every rcar_thermal_update_temp() return value will be checked.
And also, rcar_thermal_get_temp() always call
rcar_thermal_update_temp() by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This patch is prepare for of-thermal support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Probe error operation and remove operation are same.
Let's use same function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Swap interrupt disable and thermal zone unregistration in the error and
remove paths, to make them more symmetrical with the initialization
path.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As soon as the interrupt has been enabled by devm_request_irq(), the
interrupt routine may be called, depending on the current status of the
hardware.
However, at that point rcar_thermal_common hasn't been initialized
complely yet. E.g. rcar_thermal_common.base is still NULL, causing a
NULL pointer dereference:
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
pgd = c0004000
[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc7-ape6evm-04564-gb6e46cb7cbe82389 #30
Hardware name: Generic R8A73A4 (Flattened Device Tree)
task: ee8953c0 ti: ee896000 task.ti: ee896000
PC is at rcar_thermal_irq+0x1c/0xf0
LR is at _raw_spin_lock_irqsave+0x48/0x54
Postpone the call to devm_request_irq() until all initialization has
been done to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Since the ctemp is used for rcar_thermal_write() in
rcar_thermal_update_temp(), the type of 'ctemp' should be "u32" instead
of "int". This patch also changes type of the helper variables 'old'
and 'new'.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
On R-Mobile APE6, since it has 3 thermal zones, ENR register
has enable bits in bit 19-16, bit 11-8 and bit 3-0.
However, on R-Car gen2, since it has 1 thermal zone, ENR register has
enable bits in bit 3-0. (In other words, the write value should always
be 0 for bit 31-4 of ENR register.)
So, this patch fixes the ENR register value using I/O resource sets.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Avoid updating the thermal zone in case an IRQ was triggered but the
temperature didn't effectively change.
Note this is not a driver issue.
Below is a captured debug trace illustrating the purpose of this patch:
out of 8 thermal zone updates, only 2 are actually necessary.
[ 41.120000] rcar_thermal_work(): cctemp=25000
[ 41.120000] rcar_thermal_work(): nctemp=30000
[ 41.120000] rcar_thermal_work(): temp is now 30000C, update thermal zone
[ 58.990000] rcar_thermal_work(): cctemp=30000
[ 58.990000] rcar_thermal_work(): nctemp=30000
[ 58.990000] rcar_thermal_work(): same temp, do not update thermal zone
[ 59.290000] rcar_thermal_work(): cctemp=30000
[ 59.290000] rcar_thermal_work(): nctemp=30000
[ 59.290000] rcar_thermal_work(): same temp, do not update thermal zone
[ 59.590000] rcar_thermal_work(): cctemp=30000
[ 59.590000] rcar_thermal_work(): nctemp=30000
[ 59.590000] rcar_thermal_work(): same temp, do not update thermal zone
[ 59.890000] rcar_thermal_work(): cctemp=30000
[ 59.890000] rcar_thermal_work(): nctemp=30000
[ 59.890000] rcar_thermal_work(): same temp, do not update thermal zone
[ 60.190000] rcar_thermal_work(): cctemp=30000
[ 60.190000] rcar_thermal_work(): nctemp=30000
[ 60.190000] rcar_thermal_work(): same temp, do not update thermal zone
[ 60.490000] rcar_thermal_work(): cctemp=30000
[ 60.490000] rcar_thermal_work(): nctemp=30000
[ 60.490000] rcar_thermal_work(): same temp, do not update thermal zone
[ 60.790000] rcar_thermal_work(): cctemp=30000
[ 60.790000] rcar_thermal_work(): nctemp=35000
[ 60.790000] rcar_thermal_work(): temp is now 35000C, update thermal zone
I suspect this may be due to sensor sampling accuracy / fluctuation,
but no formal proof.
Signed-off-by: Patrick Titiano <ptitiano@baylibre.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Mask is already applied preceding the if statement.
Remove the second mask.
Signed-off-by: Patrick Titiano <ptitiano@baylibre.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Current rcar_thermal() didn't care about own power.
Without this patch, rcar_thermal doesn't work on APE6 board
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Current rcar_thermal driver didn't care about rcar_theraml_irq_disable()
when registration failure case on _probe(), and _remove().
And, it returns without unregistering thermal zone when
registration failure case on _probe().
This patch fixes these issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
thermal_zone_device_register returns a value contained in the pointer itself
use PTR_ERR to obtain the address and return it at the end.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Add the missing unlock before return from function rcar_thermal_update_temp()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
commit 76cc18874 "thermal: rcar: add Device Tree support"
added device tree support for this driver, but also added
an instance of __devinitconst, which is no longer defined
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Support for loading the Renesas R-Car thermal module via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Machine/System power-off is run in thermal frame work if
it become critical temperature.
This patch removed pointless machine_power_off()
from thermal_zone_device_ops :: .notify
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds interrupt support for R-Car thermal driver.
New generation R-Car thermal sensor interrupt controller was
different from old generation.
This patch supports new generation sensor only,
since the old generation interrupt controller had never been used before,
and will never be used in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
R-Car thermal driver will use struct common in next
feature (interrupt support).
But the register address is different between struct priv and common.
This patch adds read/write functions for struct common,
and use macro technique to avoid wrong register access.
This is preparation patch for next feature (interrupt support),
therefore, there is no user to use this common read/write
function at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
R-Car thermal sensor will be multi channel sensor in next generation.
But "IRQ controlling method" and "register mapping" are
different between old/new chip.
This patch adds multi sensor support.
Then, this driver assumes there is common register
if platform has IRQ resource.
The IRQ will be supported soon.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Current R-Car thermal driver is using spin lock for each
registers read/write, but it is pointless lock.
This lock is required while reading temperature,
but it needs long wait (= 300ms).
So, this patch used mutex lock while reading temperature,
instead of spin lock for each registers.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
If CPCTL was 1 on R-Car thermal, the thermal comparator offset
is automatically decided by hardware.
And this CPCTL is the conditions which validate interrupt.
This patch enabled CPCTL.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds .get_trip_type(), .get_trip_temp(), and .notify()
on rcar_thermal_zone_ops.
Driver will try platform power OFF if it reached to
critical temperature.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds rcar_zone_to_priv()
which is a helper macro for gettign private data.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The unit of temperature is Milli-Celsius.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
devm_kfree and devm_iounmap should not have to be explicitly used
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds the thermal zone parameter as an argument to
the tzd_register() function call; and updates other drivers
using this function.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
following were the errors reported
drivers/thermal/rcar_thermal.c: In function ‘rcar_thermal_probe’:
drivers/thermal/rcar_thermal.c:214:10: warning: passing argument 3 of ‘thermal_zone_device_register’ makes integer from pointer without a cast [enabled by default]
include/linux/thermal.h:166:29: note: expected ‘int’ but argument is of type ‘struct rcar_thermal_priv *’
drivers/thermal/rcar_thermal.c:214:10: error: too few arguments to function ‘thermal_zone_device_register’
include/linux/thermal.h:166:29: note: declared here
make[1]: *** [drivers/thermal/rcar_thermal.o] Error 1
make: *** [drivers/thermal/rcar_thermal.o] Error 2
with gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5)
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch add basic Renesas R-Car thermal sensor support.
It was tested on R-Car H1 Marzen board.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
