This patch unregisters the gpio chip before bcma gets unloaded.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old bcm47xx gpio code had support for gpio_to_irq, but the new
code did not provide this function, but returned -ENXIO all the time.
This patch adds the missing function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sanity checks allow 1 and 2 byte reads/writes of the extended
PCI config space to proceed; however, the code only supports 4
byte reads/writes. This patch adds support for 1 and 2 byte
reads/writes of the extended PCI config space.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PCI config space access offsets < 256 for device '0',
bcma_extpci_write_config performs an 'ioremap_nocache' on a 4 byte
section of the PCI config space (an area that has already
previously been mapped), and then subsequently unmaps that 4 byte
section. This can't be a good thing for future read access from
that now unmapped location. Modify the config space writes to use
the existing access functions (similar to how it is done for the reads).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consistently jump to the 'out' label for error conditions (adds
missing check for 'func' validity in bcma_extpci_write_config).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'val' has already been read by the prior call to 'mips_busprobe32';
this 'readl' is unnecessary.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default irqflag assignment for the I2S core on some Broadcom
4716/4748 devices is invalid and needs to be corrected (from the
Broadcom SDK).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the PCI configuration for BCM4706 and BCM4716 per the 2011
Broadcom SDK.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The irq signal numbers that are send by the cpu are increased by 2 from
the number programmed into the mips core by bcma.
Return the irq number on which the irqs are send in bcma_core_irq() now.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This error was introduced in:
commit e3f05a42fa
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Fri Jan 4 00:51:21 2013 +0100
bcma: mips: explicit assign IRQ numbers
CC drivers/bcma/driver_mips.o
drivers/bcma/driver_mips.c: In function 'bcma_core_mips_init':
drivers/bcma/driver_mips.c:302:4: error: implicit declaration of
function 'bcma_core_irq' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[6]: *** [drivers/bcma/driver_mips.o] Error 1
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new name better matches the use of this variable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some cores do not have a IRQ assigned and some do not support when an
IRQ is assigned to them, this is now handled and printed out in the
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assignment of the IRQs to the cores of the chips by iterating over
the cores is complicated and causes problems with SoC like the BCM4706
with two GMAC core where just one should get a dedicated IRQ number.
Now the code assigns the same IRQs to the cores as the code from the
Broadcom SDK does. If the SoC is not know the current assigned IRQs are
only read out and an error message is printed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This bcma_find_core_unit() is needed by the mips driver in the next
patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit cf0936b06d ("bcma: add GPIO driver")
added BCMA_DRIVER_GPIO, which unconditionally selects GPIOLIB, causing
a Kconfig warning:
warning: (ARCH_REQUIRE_GPIOLIB && SSB_DRIVER_GPIO && BCMA_DRIVER_GPIO && MFD_TC6393XB && FB_VIA) selects GPIOLIB which has unmet direct dependencies (ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB)
and build failure for m68k/allmodconfig:
In file included from include/linux/bcma/bcma.h:8,
from drivers/bcma/bcma_private.h:9,
from drivers/bcma/main.c:9:
include/linux/bcma/bcma_driver_chipcommon.h:582: error: field ‘gpio’ has incomplete type
In file included from include/linux/bcma/bcma.h:12,
from drivers/bcma/bcma_private.h:9,
from drivers/bcma/main.c:9:
include/linux/ssb/ssb.h:440: error: field ‘gpio’ has incomplete type
make[4]: *** [drivers/bcma/main.o] Error 1
make[3]: *** [drivers/bcma/] Error 2
Turn the select into a dependency to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlDSAa4ACgkQdwG7hYl686MMcACeNYa//ghPtccb5L+IRXsqaFDL
Yi4AoLWOaOjN8qM4KUF/bfMEkwNGAePz
=DaAQ
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd
Pull MTD updates from David Woodhouse:
- Various cleanups especially in NAND tests
- Add support for NAND flash on BCMA bus
- DT support for sh_flctl and denali NAND drivers
- Kill obsolete/superceded drivers (fortunet, nomadik_nand)
- Fix JFFS2 locking bug in ENOMEM failure path
- New SPI flash chips, as usual
- Support writing in 'reliable mode' for DiskOnChip G4
- Debugfs support in nandsim
* tag 'for-linus-20121219' of git://git.infradead.org/linux-mtd: (96 commits)
mtd: nand: typo in nand_id_has_period() comments
mtd: nand/gpio: use io{read,write}*_rep accessors
mtd: block2mtd: throttle writes by calling balance_dirty_pages_ratelimited.
mtd: nand: gpmi: reset BCH earlier, too, to avoid NAND startup problems
mtd: nand/docg4: fix and improve read of factory bbt
mtd: nand/docg4: reserve bb marker area in ecclayout
mtd: nand/docg4: add support for writing in reliable mode
mtd: mxc_nand: reorder part_probes to let cmdline override other sources
mtd: mxc_nand: fix unbalanced clk_disable() in error path
mtd: nandsim: Introduce debugfs infrastructure
mtd: physmap_of: error checking to prevent a NULL pointer dereference
mtg: docg3: potential divide by zero in doc_write_oob()
mtd: bcm47xxnflash: writing support
mtd: tests/read: initialize buffer for whole next page
mtd: at91: atmel_nand: return bit flips for the PMECC read_page()
mtd: fix recovery after failed write-buffer operation in cfi_cmdset_0002.c
mtd: nand: onfi need to be probed in 8 bits mode
mtd: nand: add NAND_BUSWIDTH_AUTO to autodetect bus width
mtd: nand: print flash size during detection
mted: nand_wait_ready timeout fix
...
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
We were using wrong IRQ number so clearing wasn't working at all.
Depending on a platform this could result in a one device having two
interrupts assigned. On BCM4706 this resulted in all IRQs being broken.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register the watchdog driver to the system if this is a SoC. Using the
watchdog on a non SoC device, like a PCIe card, will make the PCIe
card die when the timeout expired, but starting it again is not
supported by bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, which is depending on the SoC type and the clock.
Calculate the number of ticks per millisecond and provide two functions
for the watchdog driver. Also return the ticks or millisecond the timer
was set to in case the provided value was bigger than the max allowed
value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mostly all bcma based devices have a PMU and the PMU watchdog should be
used and not the old one in chip common. This patch also calculates the
maximal number the watchdog could be set to.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For devices without a PMU the alp clock is always 20000000.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the following warning:
CC drivers/bcma/driver_pci_host.o
drivers/bcma/driver_pci_host.c: In function 'bcma_core_pci_fixup_addresses':
drivers/bcma/driver_pci_host.c:555:23: error: ignoring return value of
'pci_assign_resource', declared with attribute warn_unused_result
[-Werror=unused-result]
Reported-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required by NAND flash driver for initializing wait counters.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Register a GPIO driver to access the GPIOs provided by the chip.
The GPIOs of the SoC should always start at 0 and the other GPIOs could
start at a random position. There is just one SoC in a system and when
they start at 0 the number is predictable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4587
Acked-by: Florian Fainelli <florian@openwrt.org>
Add functions to access the GPIO registers for pullup and pulldown.
These are needed for handling gpio registration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4586
Acked-by: Florian Fainelli <florian@openwrt.org>
The GPIOs are access through some registers in the chip common core.
We need locking around these GPIO accesses, all GPIOs are accessed
through the same registers and parallel writes will cause problems.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4585
Acked-by: Florian Fainelli <florian@openwrt.org>
This will fix warnings like following when CONFIG_PM_SLEEP is not set:
warning: 'xxx_suspend' defined but not used [-Wunused-function]
warning: 'xxx_resume' defined but not used [-Wunused-function]
Because
SET_SYSTEM_SLEEP_PM_OPS(suspend_fn, resume_fn)
Only references the callbacks on CONFIG_PM_SLEEP (instead of CONFIG_PM).
Cc: John W. Linville <linville@tuxdriver.com>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before it was tried to initialize the deactivated PCIe core in client
mode, but this causes the SoC to hang. Just do not initialize it at all
and ignore the core it is not working and nothing is connected to it
when the specific bit is set in the boardflags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCM4706 has two PCIe host controller on the bcma bus. For PCIe
client mode it is assumed that there is only one PCIe controller so the
PCIe driver, like b43 and brcmsmac are accessing the first PCIe
controller when they want to issue a operation on the host controller.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes the PCIe card indicates that it has a sprom somewhere and we
are able to read the memory region, but it is empty and not valid. In
these cases we should try to use the fallback sprom as a last chance.
This is the case for the PCIe cards in my ASUS RT-N66U (BCM4706 + 2
times BCM4331) and I have heard of someone having the same problem with
an other PCIe card connected to an other Broadcom SoC.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some devices which are able to boot from nand flash and other
are using a serial flash for booting. Add a bool to indicate that the
device is booted from that flash chip and not from some other chip also
connected to the SoC. This is needed to find the nvram, as it is stored
on the flash the devices booted from.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIe host driver and the chip common initialisation accesses the
sprom struct, but it is not initialized when these functions are run.
Move the sprom parsing up in to do it earlier.
As we need the chip common core rev and some other attributes from the
chip common core, the early initialization is done before accessing the
sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some parts of the initialization for chip common and the pcie core are
accessing the sprom struct, but it is not initialized at that stage.
Just do the necessary thing in the early register on SoCs and not the
complete initialization to read out the nvram from the flash chip.
After it is possible to read out the nvram, the sprom should be parsed
from it and the full initialization of the cores should be run.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
