Currently the unsigned variable tmp is being checked for an negative
error return from the call to bcm_phy_read_rdb and this can never
be true since tmp is unsigned. Fix this by making tmp a plain int.
Addresses-Coverity: ("Unsigned compared against 0")
Fixes: 4406d36dfd ("net: phy: bcm54140: add hwmon support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear the link partner advertisement, speed, duplex and pause when
the link goes down, as other phylib drivers do. This avoids the
stale link partner, speed and duplex settings being reported via
ethtool.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_ll2.c:2334:20: warning: symbol 'll2_cbs'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soft lock should be taken in place of hard lock.
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x25_lapb_receive_frame() invokes x25_get_neigh(), which returns a
reference of the specified x25_neigh object to "nb" with increased
refcnt.
When x25_lapb_receive_frame() returns, local variable "nb" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one path of
x25_lapb_receive_frame(). When pskb_may_pull() returns false, the
function forgets to decrease the refcnt increased by x25_get_neigh(),
causing a refcnt leak.
Fix this issue by calling x25_neigh_put() when pskb_may_pull() returns
false.
Fixes: cb101ed2c3 ("x25: Handle undersized/fragmented skbs")
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn>
Signed-off-by: Xin Tan <tanxin.ctf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Normal there should be checked for nla_put_in6_addr like other
usage in net.
Detected by CoverityScan, CID# 1461639
Fixes: 01cacb00b3 ("mptcp: add netlink-based PM")
Signed-off-by: Bo YU <tsu.yubo@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ixp4xx_eth_probe() does not perform sufficient error
checking after executing devm_ioremap_resource(), which can result
in crashes if a critical error path is encountered.
Fixes: f458ac4797 ("ARM/net: ixp4xx: Pass ethernet physical base as resource")
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SIGCHLD fix from Eric Biederman:
"Christof Meerwald reported that do_notify_parent has not been
successfully populating si_pid and si_uid for multi-threaded
processes.
This is the one-liner fix. Strictly speaking a one-liner plus
comment"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signal: Avoid corrupting si_pid and si_uid in do_notify_parent
The CPSW misc IRQ need be enabled for CPTS event_pend IRQs processing. This
patch adds corresponding support to CPSW driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hence CPTS IRQ support is in place the W_TS_PUSH events can be added.
PWM capable DmTimers can be used to generete input signals for CPTS on TI
AM335x/AM437x/DRA7 SoCs to be timestamped:
AM335x/AM437x: timer4 - timer7
DRA7/AM57xx: timer13 - timer16
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CPTS IRQ support, but do not enable it. By default, the CPTS driver
will continue working using polling mode which is required for CPTS to
continue working on platforms other than CPSW, like Keystone 2.
The CPTS IRQ support is required to enable support for HW_TS_PUSH events.
The CPSW CPTS IRQ and HW_TS_PUSH events support will be enabled in follow
up patches.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now spinlock is used to synchronize everything which is not required. Add
mutex and use to sync access to PTP interface and PTP worker and use
spinlock only to sync FIFO/events processing.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the tx timestamp processing happens from different contexts - softirq
and thread/PTP worker. Enabling IRQ will add one more hard_irq context.
This makes over all defered TX timestamp processing and locking
overcomplicated. Move tx timestamp processing to PTP worker always instead.
napi_rx->cpts_tx_timestamp
if ptp_packet then
push to txq
ptp_schedule_worker()
do_aux_work->cpts_overflow_check
cpts_process_events()
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the CPTS driver performs packet (skb) parsing every time when it needs
to match packet to CPTS event (including ptp_classify_raw() calls).
This patch optimizes matching process by parsing packet only once upon
arrival and stores PTP specific data in skb->cb using the same fromat as in
CPTS HW event. As result, all future matching reduces to comparing two u32
values.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPTS HW latches and saves CPTS counter value in CPTS fifo immediately
after writing to CPSW_CPTS_PUSH.TS_PUSH (bit 0), so the total time that the
driver needs to read the CPTS timestamp is the time required CPSW_CPTS_PUSH
write to actually reach HW.
Hence switch CPTS driver to implement new .gettimex64() callback for more
precise measurement of the offset between a PHC and the system clock which
is measured as time between
write(CPSW_CPTS_PUSH)
read(CPSW_CPTS_PUSH)
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPTS driver .adjfreq() generates request to read CPTS current time
(CPTS_EV_PUSH) with intention to process all pending event using previous
frequency adjustment values before switching to the new ones. So
CPTS_EV_PUSH works as a marker to switch to the new frequency adjustment
values. Current code assumes that all job is done in .adjfreq(), but after
enabling IRQ this will not be true any more.
Hence save new frequency adjustment values (mult) and perform actual freq
adjustment in cpts_fifo_read() immediately after CPTS_EV_PUSH is received.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPTS HW time reading code is implemented in timecounter->cyclecounter
.read() callback and performs following operations:
timecounter_read() ->cc.read() -> cpts_systim_read()
- request current CPTS HW time CPTS_TS_PUSH.TS_PUSH = 1
- poll CPTS FIFO for CPTS_EV_PUSH event with current HW timestamp
This approach need to be changed for the future switch to PTP PHC
.gettimex64() callback, which require to separate requesting current CPTS
HW time and processing CPTS FIFO. And for the follow up patch, which
improves .adjfreq() implementation.
This patch moves code accessing CPTS HW out of timecounter code as
following:
- convert HW timestamp of every CPTS event to PTP time (us) and store it as
part struct cpts_event;
- add CPTS context field to store current CPTS HW time (counter) value and
update it on CPTS_EV_PUSH reception;
- move code accessing CPTS HW out of timecounter code and use current CPTS
HW time (counter) from CPTS context instead;
- ensure timecounter->cycle_last is updated on CPTS_EV_PUSH reception.
After this change CPTS timecounter will only perform timekeeper role
without actually accessing CPTS HW.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_yy() API instead of pr_yy() for log outputs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: napi: addition of napi_defer_hard_irqs
This patch series augments gro_glush_timeout feature with napi_defer_hard_irqs
As extensively described in first patch changelog, this can suppresss
the chit-chat traffic between NIC and host to signal interrupts and re-arming
them, since this can be an issue on high speed NIC with many queues.
The last patch in this series converts mlx4 TX completion to
napi_complete_done(), to enable this new mechanism.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to benefit from the new napi_defer_hard_irqs feature,
we need to use napi_complete_done() variant in this driver.
RX path is already using it, this patch implements TX completion side.
mlx4_en_process_tx_cq() now returns the amount of retired packets,
instead of a boolean, so that mlx4_en_poll_tx_cq() can pass
this value to napi_complete_done().
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gro_flush_timeout and napi_defer_hard_irqs can be read
from napi_complete_done() while other cpus write the value,
whithout explicit synchronization.
Use READ_ONCE()/WRITE_ONCE() to annotate the races.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in commit 3b47d30396 ("net: gro: add a per device gro flush timer")
we added the ability to arm one high resolution timer, that we used
to keep not-complete packets in GRO engine a bit longer, hoping that further
frames might be added to them.
Since then, we added the napi_complete_done() interface, and commit
364b605573 ("net: busy-poll: return busypolling status to drivers")
allowed drivers to avoid re-arming NIC interrupts if we made a promise
that their NAPI poll() handler would be called in the near future.
This infrastructure can be leveraged, thanks to a new device parameter,
which allows to arm the napi hrtimer, instead of re-arming the device
hard IRQ.
We have noticed that on some servers with 32 RX queues or more, the chit-chat
between the NIC and the host caused by IRQ delivery and re-arming could hurt
throughput by ~20% on 100Gbit NIC.
In contrast, hrtimers are using local (percpu) resources and might have lower
cost.
The new tunable, named napi_defer_hard_irqs, is placed in the same hierarchy
than gro_flush_timeout (/sys/class/net/ethX/)
By default, both gro_flush_timeout and napi_defer_hard_irqs are zero.
This patch does not change the prior behavior of gro_flush_timeout
if used alone : NIC hard irqs should be rearmed as before.
One concrete usage can be :
echo 20000 >/sys/class/net/eth1/gro_flush_timeout
echo 10 >/sys/class/net/eth1/napi_defer_hard_irqs
If at least one packet is retired, then we will reset napi counter
to 10 (napi_defer_hard_irqs), ensuring at least 10 periodic scans
of the queue.
On busy queues, this should avoid NIC hard IRQ, while before this patch IRQ
avoidance was only possible if napi->poll() was exhausting its budget
and not call napi_complete_done().
This feature also can be used to work around some non-optimal NIC irq
coalescing strategies.
Having the ability to insert XX usec delays between each napi->poll()
can increase cache efficiency, since we increase batch sizes.
It also keeps serving cpus not idle too long, reducing tail latencies.
Co-developed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the absence of MC1, the size calculation function
cudbg_mem_region_size() was returing wrong MC size and
resulted in adapter crash. This patch adds new argument
to cudbg_mem_region_size() which will have actual size
and returns error to caller in the absence of MC1.
Fixes: a1c69520f7 ("cxgb4: collect MC memory dump")
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>"
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca says:
====================
net: vxlan/geneve: use the correct nlattr array for extack
The ->validate callbacks for vxlan and geneve have a couple of typos
in extack, where the nlattr array for IFLA_* attributes is used
instead of the link-specific one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_GENEVE_* attributes are in the data array, which is correctly
used when fetching the value, but not when setting the extended
ack. Because IFLA_GENEVE_MAX < IFLA_MAX, we avoid out of bounds
array accesses, but we don't provide a pointer to the invalid
attribute to userspace.
Fixes: a025fb5f49 ("geneve: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_VXLAN_* attributes are in the data array, which is correctly
used when fetching the value, but not when setting the extended
ack. Because IFLA_VXLAN_MAX < IFLA_MAX, we avoid out of bounds
array accesses, but we don't provide a pointer to the invalid
attribute to userspace.
Fixes: 653ef6a3e4 ("vxlan: change vxlan_[config_]validate() to use netlink_ext_ack for error reporting")
Fixes: b4d3069783 ("vxlan: Allow configuration of DF behaviour")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru says:
====================
qed*: Add support for pcie advanced error recovery.
The patch series adds qed/qede driver changes for PCIe Advanced Error
Recovery (AER) support.
Patch (1) adds qed changes to enable the device to send error messages
to root port when detected.
Patch (2) adds qede support for handling the detected errors (AERs).
Changes from previous version:
-------------------------------
v2: use pci_num_vf() instead of caching the value in edev.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The error recovery is handled by management firmware (MFW) with the help of
qed/qede drivers. Upon detecting the errors, driver informs MFW about this
event which in turn starts a recovery process. MFW sends ERROR_RECOVERY
notification to the driver which performs the required cleanup/recovery
from the driver side.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch enables the device to send error messages to root port when
an error is detected.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw_sp_acl_rulei_create() function is supposed to return an error
pointer from mlxsw_afa_block_create(). The problem is that these
functions both return NULL instead of error pointers. Half the callers
expect NULL and half expect error pointers so it could lead to a NULL
dereference on failure.
This patch changes both of them to return error pointers and changes all
the callers which checked for NULL to check for IS_ERR() instead.
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gro_cells lib is used by different encapsulating netdevices, such as
geneve, macsec, vxlan etc. to speed up decapsulated traffic processing.
CPU tag is a sort of "encapsulation", and we can use the same mechs to
greatly improve overall DSA performance.
skbs are passed to the GRO layer after removing CPU tags, so we don't
need any new packet offload types as it was firstly proposed by me in
the first GRO-over-DSA variant [1].
The size of struct gro_cells is sizeof(void *), so hot struct
dsa_slave_priv becomes only 4/8 bytes bigger, and all critical fields
remain in one 32-byte cacheline.
The other positive side effect is that drivers for network devices
that can be shipped as CPU ports of DSA-driven switches can now use
napi_gro_frags() to pass skbs to kernel. Packets built that way are
completely non-linear and are likely being dropped without GRO.
This was tested on to-be-mainlined-soon Ethernet driver that uses
napi_gro_frags(), and the overall performance was on par with the
variant from [1], sometimes even better due to minimal overhead.
net.core.gro_normal_batch tuning may help to push it to the limit
on particular setups and platforms.
iperf3 IPoE VLAN NAT TCP forwarding (port1.218 -> port0) setup
on 1.2 GHz MIPS board:
5.7-rc2 baseline:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 9.00 GBytes 644 Mbits/sec 413 sender
[ 5] 0.00-120.00 sec 8.99 GBytes 644 Mbits/sec receiver
Iface RX packets TX packets
eth0 7097731 7097702
port0 426050 6671829
port1 6671681 425862
port1.218 6671677 425851
With this patch:
[ID] Interval Transfer Bitrate Retr
[ 5] 0.00-120.01 sec 12.2 GBytes 870 Mbits/sec 122 sender
[ 5] 0.00-120.00 sec 12.2 GBytes 870 Mbits/sec receiver
Iface RX packets TX packets
eth0 9474792 9474777
port0 455200 353288
port1 9019592 455035
port1.218 353144 455024
v2:
- Add some performance examples in the commit message;
- No functional changes.
[1] https://lore.kernel.org/netdev/20191230143028.27313-1-alobakin@dlink.ru/
Signed-off-by: Alexander Lobakin <bloodyreaper@yandex.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV_V2_PORT_CTRL_SWRST bit in MV_V2_PORT_CTRL is reserved on 88E2110.
Setting SWRST on 88E2110 breaks packets transfer after interface down/up
cycle.
Fixes: 8f48c2ac85 ("net: marvell10g: soft-reset the PHY when coming out of low power")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4862 5.5.3 e) prevents received Router Advertisements from reducing
the Valid Lifetime of configured addresses to less than two hours, thus
preventing hosts from reacting to the information provided by a router
that has positive knowledge that a prefix has become invalid.
This patch makes hosts honor all Valid Lifetime values, as per
draft-gont-6man-slaac-renum-06, Section 4.2. This is meant to help
mitigate the problem discussed in draft-ietf-v6ops-slaac-renum.
Note: Attacks aiming at disabling an advertised prefix via a Valid
Lifetime of 0 are not really more harmful than other attacks
that can be performed via forged RA messages, such as those
aiming at completely disabling a next-hop router via an RA that
advertises a Router Lifetime of 0, or performing a Denial of
Service (DoS) attack by advertising illegitimate prefixes via
forged PIOs. In scenarios where RA-based attacks are of concern,
proper mitigations such as RA-Guard [RFC6105] [RFC7113] should
be implemented.
Signed-off-by: Fernando Gont <fgont@si6networks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=aONb
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Workaround Apex TPU class code issue that prevents resource
assignment (Bjorn Helgaas)
- Update MAINTAINERS to add Rob Herring for native PCI controller
drivers (Lorenzo Pieralisi)
* tag 'pci-v5.7-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add Rob Herring and remove Andy Murray as PCI reviewers
PCI: Move Apex Edge TPU class quirk to fix BAR assignment
A few smaller fixes for v5.7-rc3: The majority are fixes for bugs I found
after restarting my randconfig build testing that had been dormant for
a while.
On the Nokia N950/N9 phone, a DT fix is required to address a boot
regression.
For the bcm283x (Raspberry Pi), two DT fixes address minor issues.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=K1jH
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few smaller fixes for v5.7-rc3: The majority are fixes for bugs I
found after restarting my randconfig build testing that had been
dormant for a while.
On the Nokia N950/N9 phone, a DT fix is required to address a boot
regression.
For the bcm283x (Raspberry Pi), two DT fixes address minor issues"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: imx8: select SOC_BUS
soc: tegra: fix tegra_pmc_get_suspend_mode definition
soc: fsl: dpio: avoid stack usage warning
soc: fsl: dpio: fix incorrect pointer conversions
ARM: imx: provide v7_cpu_resume() only on ARM_CPU_SUSPEND=y
ARM: dts: bcm283x: Disable dsi0 node
firmware: xilinx: make firmware_debugfs_root static
drivers: soc: xilinx: fix firmware driver Kconfig dependency
ARM: dts: bcm283x: Add cells encoding format to firmware bus
ARM: dts: OMAP3: disable RNG on N950/N9
- Address several use-after-free and memory leak bugs
- Prevent a backchannel livelock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Zoup
-----END PGP SIGNATURE-----
Merge tag 'nfsd-5.7-rc-1' of git://git.linux-nfs.org/projects/cel/cel-2.6
Pull nfsd fixes from Chuck Lever:
"The first set of 5.7-rc fixes for NFS server issues.
These were all unresolved at the time the 5.7 window opened, and
needed some additional time to ensure they were correctly addressed.
They are ready now.
At the moment I know of one more urgent issue regarding the NFS
server. A fix has been tested and is under review. I expect to send
one more pull request, containing this fix (which now consists of 3
patches).
Fixes:
- Address several use-after-free and memory leak bugs
- Prevent a backchannel livelock"
* tag 'nfsd-5.7-rc-1' of git://git.linux-nfs.org/projects/cel/cel-2.6:
svcrdma: Fix leak of svc_rdma_recv_ctxt objects
svcrdma: Fix trace point use-after-free race
SUNRPC: Fix backchannel RPC soft lockups
SUNRPC/cache: Fix unsafe traverse caused double-free in cache_purge
nfsd: memory corruption in nfsd4_lock()
This fixes a regression in the probe error path of the Qualcomm modem
remoteproc driver and a mix up of phy_addr_t and dma_addr_t in the
Mediatek SCP control driver.
-----BEGIN PGP SIGNATURE-----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=WDtr
-----END PGP SIGNATURE-----
Merge tag 'rproc-v5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc fixes from Bjorn Andersson:
"This fixes a regression in the probe error path of the Qualcomm modem
remoteproc driver and a mix up of phy_addr_t and dma_addr_t in the
Mediatek SCP control driver"
* tag 'rproc-v5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
remoteproc: mtk_scp: use dma_addr_t for DMA API
remoteproc: qcom_q6v5_mss: fix q6v5_probe() error paths
remoteproc: qcom_q6v5_mss: fix a bug in q6v5_probe()
-----BEGIN PGP SIGNATURE-----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=Qn3Z
-----END PGP SIGNATURE-----
Merge tag 'audit-pr-20200422' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"One small audit patch fix, fixing a missing length check on input from
userspace, nothing crazy"
* tag 'audit-pr-20200422' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: check the length of userspace generated audit records
Move all zoned mode related code from null_blk_main.c to
null_blk_zoned.c, avoiding an ugly #ifdef in the process.
Rename null_zone_init() into null_init_zoned_dev(), null_zone_exit()
into null_free_zoned_dev() and add the new function
null_register_zoned_dev() to finalize the zoned dev setup before
add_disk().
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For write operations issued to a null_blk device with zoned mode
enabled, the state and write pointer position of the zone targeted by
the command should be checked before badblocks and memory backing
are handled as the write may be first failed due to, for instance, a
sector position not aligned with the zone write pointer. This order of
checking for errors reflects more accuratly the behavior of physical
zoned devices.
Furthermore, the write pointer position of the target zone should be
incremented only and only if no errors are reported by badblocks and
memory backing handling.
To fix this, introduce the small helper function null_process_cmd()
which execute null_handle_badblocks() and null_handle_memory_backed()
and use this function in null_zone_write() to correctly handle write
requests to zoned null devices depending on the type and state of the
write target zone. Also call this function in null_handle_zoned() to
process read requests to zoned null devices.
null_process_cmd() is called directly from null_handle_cmd() for
regular null devices, resulting in no functional change for these type
of devices. To have symmetric names, the function null_handle_zoned()
is renamed to null_process_zoned_cmd().
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
5.7, please pull the following:
- Nicolas provides a fix for 55c7c06210 ("ARM: dts: bcm283x: Fix vc4's
firmware bus DMA limitations") which missed adding proper
#address-cells and #size-cells properties and he also disables the DSI
node which should have been disabled by default but was not.
-----BEGIN PGP SIGNATURE-----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=6CKq
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.7/devicetree-fixes' of https://github.com/Broadcom/stblinux into arm/fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.7, please pull the following:
- Nicolas provides a fix for 55c7c06210 ("ARM: dts: bcm283x: Fix vc4's
firmware bus DMA limitations") which missed adding proper
#address-cells and #size-cells properties and he also disables the DSI
node which should have been disabled by default but was not.
* tag 'arm-soc/for-5.7/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Disable dsi0 node
ARM: dts: bcm283x: Add cells encoding format to firmware bus
Link: https://lore.kernel.org/r/20200417171725.1084-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
HD-audio codec driver applies a tricky procedure to forcibly perform
the runtime resume by mimicking the usage count even if the device has
been runtime-suspended beforehand. This was needed to assure to
trigger the jack detection update after the system resume.
And recently we also applied the similar logic to the HD-audio
controller side. However this seems leading to some inconsistency,
and eventually PCI controller gets screwed up.
This patch is an attempt to fix and clean up those behavior: instead
of the tricky runtime resume procedure, the existing jackpoll work is
scheduled when such a forced codec resume is required. The jackpoll
work will power up the codec, and this alone should suffice for the
jack status update in usual cases. If the extra polling is requested
(by checking codec->jackpoll_interval), the manual update is invoked
after that, and the codec is powered down again.
Also, we filter the spurious wake up of the codec from the controller
runtime resume by checking codec->relaxed_resume flag. If this flag
is set, basically we don't need to wake up explicitly, but it's
supposed to be done via the audio component notifier.
Fixes: c4c8dd6ef8 ("ALSA: hda: Skip controller resume if not needed")
Link: https://lore.kernel.org/r/20200422203744.26299-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
