Use 'clock-frequency' binding for the i2c node that will put the I2C driver
into the standard operating mode. 'speed-mode' was not a valid binding for
the I2C driver, remove it.
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the Altera Arria10 System Resource Reset Controller to the MFD
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v2 change commit header to ARM: dts: socfpga.
Memory nodes in Arria5, Cyclone5 and Arria10 do not have a unit name.
This will trigger several warnings like this one (when compiled with
W=1):
Node /memory has a reg or ranges property, but no unit name
Add the corresponding unit name to each node.
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
On the Arria10, because of hardware bug, watchdog0 cannot reliably trigger
a reset to the CPU. The workaround would be to use watchdog1 instead.
Also for watchdog1, there is a dependency on the bootloader to enable the
boot_clk source to be from the cb_intosc_hs_clk/2, versus from EOSC1. This
corresponds to the (SWCTRLBTCLKEN & SWCTRLBTCLKSEL) bits enabled in the
control register in the clock manager module of Arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the LED framework to the Arria10 System Resource chip GPIO hooks.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the Altera Arria10 System Resource node. This is a Multi-Function
device with GPIO expander support.
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The notion of which uart instance is serial0 or serial1
is board specific rather than generic to the chip. This
patch removes the serial aliases from generic chip dtsi
and adds an appropriate alias to the board specific dtsi.
By making the alias for serial0 point to uart1 for the arria10_socdk,
the linux boot command line supports specifying console=ttyS0,115200
for backwards compatibility, and it supports not specifying
the console at all.
Signed-off-by: Matthew Gerlach <mgerlach@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Without having an ethernet alias, ethernet will have a random MAC address,
versus take an address that was provided from the bootloader.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
On the Arria10 Devkit, the I2C bus has a serial EEPROM and an RTC
hanging off it. Also, enable the USB node.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Update the arria10 gmac nodes with all the necessary properties for ethernet
to function on the Arria10 devkit.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Rename the socfpga_arria10_socdk board file to socfpga_arria10_socdk_sdmmc
as Arria 10 devkit cannot support SDMMC and QSPI at the same time. Thus
we will need to have 2 separate board files, one for SDMMC and one for
QSPI. We also add a new base board dtsi file, socfpga_arria10_socdk.dtsi
so that we use common peripherals for each flavor of the devkits.
Add the sdmmc node to the socfpga_arria10_socdk_sdmmc.dts board file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
