Neither the m25_div_clk nor the m250_div_clk or m250_mux_clk are used in
RMII mode. The m25_div_clk output is routed to the RGMII PHY's "RGMII
clock".
This means that we don't need to configure the clocks in RMII mode. The
driver however did this - with no effect since the clocks are not routed
to the PHY in RMII mode.
While here also rename meson8b_init_clk to meson8b_init_rgmii_tx_clk to
make it easier to understand the code.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_div_table are not supposed to change at runtime.
meson8b_dwmac structure is working with const clk_div_table.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As documented in Documentation/devicetree/bindings/net/ethernet.txt,
in RGMII_ID and RGMII_TXID mode the MAC should not add a tx delay.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch we were using a hardcoded RGMII TX clock delay of
2ns (= 1/4 cycle of the 125MHz RGMII TX clock). This value works for
many boards, but unfortunately not for all (due to the way the actual
circuit is designed, sometimes because the TX delay is enabled in the
PHY, etc.). Making the TX delay on the MAC side configurable allows us
to support all possible hardware combinations.
This allows fixing a compatibility issue on some boards, where the
RTL8211F PHY is configured to generate the TX delay. We can now turn
off the TX delay in the MAC, because otherwise we would be applying the
delay twice (which results in non-working TX traffic).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to deregister and free any fixed-link phy registered during
probe on probe errors and on driver unbind by adding a new glue helper
function.
Drop the of-node reference taken in the same path also on late probe
errors (and not just on driver unbind) by moving the put from
stmmac_dvr_remove() to the new helper.
Fixes: 277323814e ("stmmac: add fixed-link device-tree support")
Fixes: 4613b279be ("ethernet: stmicro: stmmac: add missing of_node_put
after calling of_parse_phandle")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to disable clocks before returning on late probe errors.
Fixes: 566e825162 ("net: stmmac: add a glue driver for the Amlogic
Meson 8b / GXBB DWMAC")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet controller available in Meson8b and GXBB SoCs is a Synopsys
DesignWare MAC IP core which is already supported by the stmmac driver.
In addition to the standard stmmac driver some Meson8b / GXBB specific
registers have to be configured for the PHY clocks. These SoC specific
registers are called PRG_ETHERNET_ADDR0 and PRG_ETHERNET_ADDR1 in the
datasheet.
These registers are not backwards compatible with those on Meson 6b,
which is why a new glue driver is introduced. This worked for many
boards because the bootloader programs the PRG_ETHERNET registers
correctly. Additionally the meson6-dwmac driver only sets bit 1 of
PRG_ETHERNET_ADDR0 which (according to the datasheet) is only used
during reset.
Currently all configuration values can be determined automatically,
based on the configured phy-mode (which is mandatory for the stmmac
driver). If required the tx-delay and the mux clock (so it supports
the MPLL2 clock as well) can be made configurable in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
