Clean up the CQM settings code a bit and while at it
enforce that when setting the threshold to 0 (disable)
the hysteresis is also set to 0 to avoid confusion.
As we haven't enforce it, simply override userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To allow channel switch announcements within beacons, add
the channel switch command to nl80211/cfg80211. This is
implementation is intended for AP and (later) IBSS mode.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a P2P GO interface goes down, cfg80211 doesn't properly
tear it down, leading to warnings later. Add the GO interface
type to the enumeration to tear it down like AP interfaces.
Otherwise, we leave it pending and mac80211's state can get
very confused, leading to warnings later.
Cc: stable@vger.kernel.org
Reported-by: Ilan Peer <ilan.peer@intel.com>
Tested-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is similar to the race Linus had reported, but in this case
it's an older bug: nl80211_prepare_wdev_dump() uses the wiphy
index in cb->args[0] as it is and thus parses the message over
and over again instead of just once because 0 is the first valid
wiphy index. Similar code in nl80211_testmode_dump() correctly
offsets the wiphy_index by 1, do that here as well.
Cc: stable@vger.kernel.org
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The dev_attrs field of struct class is going away soon, dev_groups
should be used instead. This converts the networking wireless class
code to use the correct field.
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current regdomain was not always set by the core. This causes
cards with a custom regulatory domain to ignore user initiated changes
if done before the card was registered.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whether the wiphy supports it or not is already checked, so what is left
is to enable these channel types.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Mandatory rates for 5 and 10 MHz are different from the rates used for
20 MHz in 2.4 GHz mode, as they use OFDM only.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
To allow scanning and working with 5 MHz and 10 MHz BSS, extend the
inform bss commands and add wrappers to take 5 and 10 MHz bss into
account.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
In most cases, host that receives IPv4 and IPv6 multicast/broadcast
packets does not do anything with these packets. Therefore the
reception of these unwanted packets causes unnecessary processing
and power consumption.
Packet coalesce feature helps to reduce number of received
interrupts to host by buffering these packets in firmware/hardware
for some predefined time. Received interrupt will be generated when
one of the following events occur.
a) Expiration of hardware timer whose expiration time is set to
maximum coalescing delay of matching coalesce rule.
b) Coalescing buffer in hardware reaches it's limit.
c) Packet doesn't match any of the configured coalesce rules.
This patch adds set/get configuration support for packet coalesce.
User needs to configure following parameters for creating a coalesce
rule.
a) Maximum coalescing delay
b) List of packet patterns which needs to be matched
c) Condition for coalescence. pattern 'match' or 'no match'
Multiple such rules can be created.
This feature needs to be advertised during driver initialization.
Drivers are supposed to do required firmware/hardware settings based
on user configuration.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[fix kernel-doc, change free function, fix copy/paste error]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Currently packet patterns and it's enum/structures are used only
for WoWLAN feature. As we intend to reuse them for new feature
packet coalesce, they are renamed in this patch.
Older names are kept for backward compatibility purpose.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
RSSI threshold value used for mesh peering should be in
negative value. After range checks to mesh parameters is
introduced, this is not allowed. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
restore_regulatory_settings() requires the RTNL to be held,
add the missing locking in reg_timeout_work().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When splitting the SME implementation from the MLME code,
I introduced a few bugs:
* association failures no longer sent a connect-failure event
* getting disassociated from the AP caused deauth to be sent
but state wasn't cleaned up, leading to warnings
* authentication failures weren't cleaned up properly, causing
new connection attempts to warn and fail
Fix these bugs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
These two events were sent to the default network
namespace.
This caused AP mode in a non-default netns to not
work correctly. Mgmt tx status was multicasted to
a different (default) netns instead of the one the
AP was in.
Cc: stable@vger.kernel.org
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The following compilation issue popped up moving from v3.10-rc1 to
v3.10-rc6 after merging wireless-testing.
net/wireless/sysfs.c:86:13: error: 'cfg80211_leave_all' defined
but not used [-Werror=unused-function]
The function is only called when CONFIG_PM is enabled. Moving the
function under CONFIG_PM as well.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If it *is* still set when the netdev is being deleted,
then we are about to leak a pointer. Warn and clean up
in that case.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Should help the next person that tries to understand
the bss refcounting logic.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the potential issue that the BSS struct that we use
and later assign to wdev->current_bss is removed from the scan
list while associating.
Also warn when we don't have a BSS struct in connect_result
unless it's from a driver that only has the connect() API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing so will allow us to hold the BSS (not just ref it) over the
association process, thus ensuring that it doesn't time out and
gets invisible to the user (e.g. in 'iw wlan0 link'.)
This also fixes a leak in mac80211 where it doesn't always release
the BSS struct properly in all cases where calling this function.
This leak was reported by Ben Greear.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid parsing the original dump message again and again by
allocating a small state struct that is used by the functions
involved in the dump, storing this struct in cb->args[0].
This reduces the memory allocation size as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since my commit 3713b4e364 ("nl80211: allow splitting wiphy
information in dumps"), nl80211_dump_wiphy() uses the global
nl80211_fam.attrbuf for parsing the incoming data. This wouldn't
be a problem if it only did so on the first dump iteration which
is locked against other commands in generic netlink, but due to
space constraints in cb->args (the needed state doesn't fit) I
decided to always parse the original message. That's racy though
since nl80211_fam.attrbuf could be used by some other parsing in
generic netlink concurrently.
For now, fix this by allocating a separate parse buffer (it's a
bit too big for the stack, currently 1448 bytes on 64-bit). For
-next, I'll change the code to parse into the global buffer in
the first round only and then allocate a smaller buffer to keep
the data in cb->args.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add defines for 5 and 10 MHz channel width and fix channel
handling functions accordingly.
Also check for and report the WIPHY_FLAG_SUPPORTS_5_10_MHZ
capability.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[fix spelling in comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
only the attributes are required and not the whole netlink info, as the
function accesses the attributes only anyway. This makes it easier to
parse nested beacon IEs later.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In two wiphy dump error cases, most often when the dump allocation
must be increased, the RTNL is leaked. This quickly results in a
complete system lockup. Release the RTNL correctly.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may want to send a frame on the current channel
without specifying it.
This is particularly useful for the correct implementation
of the IBSS/RSN support in wpa_supplicant which requires to
receive and send AUTH frames.
Make mgmt_tx pass a NULL channel to the driver if none has
been specified by the user.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I (Johannes) accidentally applied the first version of the patch
("Allow TDLS peer AID to be configured for VHT"). Now apply just
the changes between v1 and v2 to get the AID verification and
prefer the new attribute over the old one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers. Previously, this inactivity time was
always 30 minutes. Now, add it to the mesh configuration
and allow it to be configured. Retain 30 minutes as a
default value.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to use atomic_inc_return() for assigning the wiphy
index made the first wiphy index 1 instead of 0. This is fine,
but we all habitually type "phy0" when we're testing, so make
it go back to 0 instead of 1 by subtracting 1 from the index.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My big locking cleanups caused a problem by registering the
rfkill instance with the RTNL held, while the callback also
acquires the RTNL. This potentially causes a deadlock since
the two locks used (rfkill mutex and RTNL) can be acquired
in two different orders. Fix this by (un)registering rfkill
without holding the RTNL. This needs to be done after the
device struct is registered, but that can also be done w/o
holding the RTNL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
get_reg_request_treatment() returns 0 in one case but is
defined to return an enum, use the proper value REG_REQ_OK.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current internal SME implementation in cfg80211 is
very mixed up with the MLME handling, which has been
causing issues for a long time. There are three things
that the implementation has to provide:
* a basic SME implementation for nl80211's connect()
call (for drivers implementing auth/assoc, which is
really just mac80211) and wireless extensions
* MLME events for the userspace SME
* SME events (connected, disconnected etc.) for all
different SME implementation possibilities (driver,
cfg80211 and userspace)
To achieve these goals it isn't necessary to track the
software SME's connection status outside of it's state
(which is the part that caused many issues.) Instead,
track it only in the SME data (wdev->conn) and in the
general case only track whether the wdev is connected
or not (via wdev->current_bss.)
Also separate the internal implementation to not have
callbacks from the SME events, but rather call it from
the API functions that the driver (or rather mac80211)
calls. This separates the code better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.
Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.
Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
genlmsg_end() can't return an error since it returns the
skb length so remove checks treating the return value as
an error code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An active monitor interface is one that is used for communication (via
injection). It is expected to ACK incoming unicast packets. This is
useful for running various 802.11 testing utilities that associate to an
AP via injection and manage the state in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the current WoWLAN configuration available to drivers
at runtime. This isn't really useful for the normal WoWLAN
behaviour and accessing it can also be racy, but drivers
may use it for testing the WoWLAN device behaviour while
the host stays up & running to observe the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reg_mutex is similar to the ones I just removed in
cfg80211 but even less useful since it protects global
data, and we hold the RTNL in all places (except module
unload) already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since it just does a quick check of the last regulatory
request, the function doesn't have to hold the reg mutex
but can use RCU instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver for some reason successfully finishes
scanning while in p2p_stop_device(), cfg80211 will
still set it to aborted. Simplify this code using the
new 'notified' value and only mark it aborted in case
the driver didn't notify cfg80211 at all (in which
case we also leak the request to not crash, this is
a driver bug.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)
Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT uses peer AID in the PARTIAL_AID field in TDLS frames. The current
design for TDLS is to first add a dummy STA entry before completing TDLS
Setup and then update information on this STA entry based on what was
received from the peer during the setup exchange.
In theory, this could use NL80211_ATTR_STA_AID to set the peer AID just
like this is used in AP mode to set the AID of an association station.
However, existing cfg80211 validation rules prevent this attribute from
being used with set_station operation. To avoid interoperability issues
between different kernel and user space version combinations, introduce
a new nl80211 attribute for the purpose of setting TDLS peer AID. This
attribute can be used in both the new_station and set_station
operations. It is not supposed to be allowed to change the AID value
during the lifetime of the STA entry, but that validation is left for
drivers to do in the change_station callback.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P-Device is present and another virtual interface triggers
the connection work, the system crash because it tries to check
if the P2P-Device's netdev (which doesn't exist) is up. Skip any
wdevs that have no netdev to fix this.
Cc: stable@vger.kernel.org
Reported-by: YanBo <dreamfly281@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication takes place in userspace, but the beacon is
generated in the kernel. Allow userspace to inform the
kernel of the authentication method so the appropriate
mesh config IE can be set prior to beacon generation when
joining the MBSS.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support auto-loading of wireless modules from netlink users, add module
alias for nl80211 family.
This also adds NL80211_GENL_NAME constant to define the "nl80211" netlink
family name as part of uapi.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add regulatory class for 60GHz band, according
to the last specification.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code sending the current WoWLAN TCP wakeup settings in
nl80211_send_wowlan_tcp() is not closing the nested attribute,
thus causing the parser to get confused on the receiver side
in userspace (iw). Fix this.
Cc: stable@vger.kernel.org [3.9]
Reported-by: Deepak Arora <deepakx.arora@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the interface goes down, there's no need to call
cfg80211_mlme_down() after __cfg80211_disconnect() as
the latter will call the former (if appropriate.)
Also, in __cfg80211_disconnect(), if the cfg80211 SME
isn't used, __cfg80211_disconnected() may still need
to be called (depending on the current state) so that
the SME state gets cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding the attributes fixes an issue with P2P Device not
working properly for management frame TX.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the device reports a non-wireless wakeup reason, the
tracing code crashes trying to dereference a NULL pointer.
Fix this by checking the pointer on all accesses and also
add a non_wireless tag to the event.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If rfkill_register() fails in wiphy_register() the struct device
is unregistered but everything else isn't (regulatory, debugfs)
and we even leave the wiphy instance on all internal lists even
though it will likely be freed soon, which is clearly a problem.
Fix this by cleaning up properly.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Don't use create_proc_read_entry() as that is deprecated, but rather use
proc_create_data() and seq_file instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Jouni Malinen <j@w1.fi>
cc: John W. Linville <linville@tuxdriver.com>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: linux-wireless@vger.kernel.org
cc: netdev@vger.kernel.org
cc: devel@driverdev.osuosl.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Some protocols need a more reliable connection to complete
successful in reasonable time. This patch adds a user-space
API to indicate the wireless driver that a critical protocol
is about to commence and when it is done, using nl80211 primitives
NL80211_CMD_CRIT_PROTOCOL_START and NL80211_CRIT_PROTOCOL_STOP.
There can be only on critical protocol session started per
registered cfg80211 device.
The driver can support this by implementing the cfg80211 callbacks
.crit_proto_start() and .crit_proto_stop(). Examples of protocols
that can benefit from this are DHCP, EAPOL, APIPA. Exactly how the
link can/should be made more reliable is up to the driver. Things
to consider are avoid scanning, no multi-channel operations, and
alter coexistence schemes.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In cfg80211_can_use_iftype_chan(), check for P2P Device
first, and then for netdevs. This doesn't really change
anything but makes the code a bit easier to read since
it may not be obvious for everyone at first that a P2P
device has no netdev.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_stop_p2p_device() requires the devlist_mtx to
be held, but nl80211_stop_p2p_device() doesn't acquire
it which is a locking error and causes a warning (when
lockdep is enabled). Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most dump callbacks, including the scan results one, use
the netdev to identify what to do, which is incorrect for
the P2P_DEVICE support, it needs to be able to get the
scan result from the wdev. Change all dumps to unify the
code, but ones other than scan don't really support being
executed on a wdev that has no netdev.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function converts a (global only!) operating
class to an internal band identifier. This will
be needed for extended channel switch support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a full scan 2.4 and 5 GHz scan is scheduled, but then the 2.4 GHz
part of the scan disables a 5.2 GHz channel due to, e.g. receiving
country or frequency information, that 5.2 GHz channel might already
be in the list of channels to scan next. Then, when the driver checks
if it should do a passive scan, that will return false and attempt an
active scan. This is not only wrong but can also lead to the iwlwifi
device firmware crashing since it checks regulatory as well.
Fix this by not setting the channel flags to just disabled but rather
OR'ing in the disabled flag. That way, even if the race happens, the
channel will be scanned passively which is still (mostly) correct.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in f9f475292d
("cfg80211: always check for scan end on P2P device")
cfg80211_conn_scan() which requires sched_scan_mtx to be held can be called
from cfg80211_conn_work(). Without this we are hitting multiple warnings like
the following:
WARNING: at net/wireless/sme.c:88 cfg80211_conn_scan+0x1dc/0x3a0 [cfg80211]()
Hardware name: 0578A21
Modules linked in: ...
Pid: 620, comm: kworker/3:1 Not tainted 3.9.0-rc4-next-20130328+ #326
Call Trace:
[<c1036992>] warn_slowpath_common+0x72/0xa0
[<c10369e2>] warn_slowpath_null+0x22/0x30
[<faa4b0ec>] cfg80211_conn_scan+0x1dc/0x3a0 [cfg80211]
[<faa4b344>] cfg80211_conn_do_work+0x94/0x380 [cfg80211]
[<faa4c3b2>] cfg80211_conn_work+0xa2/0x130 [cfg80211]
[<c1051858>] process_one_work+0x198/0x450
Signed-off-by: Artem Savkov <artem.savkov@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.
Also update all the users of this value that David Miller and
I could find to use the new constant.
Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.
As suggested by Jesse Gross.
Compile tested only.
Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a P2P device wdev is removed while it has a scan, then the
scan completion might crash later as it is already freed by
that time. To avoid the crash always check the scan completion
when the P2P device is being removed for some reason. If the
driver already canceled it, don't want and free it, otherwise
warn and leak it to avoid later crashes.
In order to do this, locking needs to be changed away from the
rdev mutex (which can't always be guaranteed). For now, use
the sched_scan_mtx instead, I'll rename it to just scan_mtx in
a later patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Arend reported a crash in tracing if the driver returns an
ERR_PTR() value from the add_virtual_intf() callback. This
is due to the tracing then still attempting to dereference
the "pointer", fix this by using IS_ERR_OR_NULL().
Reported-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If wpa_supplicant and iw/iwconfig are used together, very
rarely the system crashes. It seems to be related to the
connection parameters not being set up, but it's not all
clear to me how this happens. In any case, checking that
the conn pointer exists here is probably a good idea.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the odd case that while updating information from a beacon,
a BSS was found that is part of a hidden group, we drop the
new information. In this case, however, we leak the IE buffer
from the update, and erroneously update the entry's timestamp
so it will never time out. Fix both these issues.
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is NETDEV_ENTRY that was incorrectly assigned as WIPHY_ASSIGN,
fix it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user requested a userspace MPM, automatically
disable auto_open_plinks to fully disable the kernel MPM.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mesh station types used to refer to whether the
station was secure or nonsecure. Really the salient
information is whether it is managed by the kernel or
userspace
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Secure mesh had the implicit requirement that the Mesh
Peering Management entity be in userspace. However
userspace might want to implement an open MPM as well, so
specify a mesh setup parameter to indicate this.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For VHT, the wider bandwidths (up to 160 MHz) need
to be allowed. Since world roaming only covers the
case of connecting to an AP, it can be opened up
there, we will rely on the AP to know the local
regulations.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason TDLS should be prevented on P2P client
interfaces, and most of the code already handles it, so
allow adding stations for it.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If possible that after suspend, cfg80211 will receive request to
disconnect what require action on interface that was removed during
suspend.
Problem can manifest itself by various warnings similar to below one:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x4
Call Trace:
[<c043e0b3>] warn_slowpath_fmt+0x33/0x40
[<f83707c9>] ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]
[<f83a660a>] ieee80211_recalc_ps_vif+0x2a/0x30 [mac80211]
[<f83a6706>] ieee80211_set_disassoc+0xf6/0x500 [mac80211]
[<f83a9441>] ieee80211_mgd_deauth+0x1f1/0x280 [mac80211]
[<f8381b36>] ieee80211_deauth+0x16/0x20 [mac80211]
[<f8261e70>] cfg80211_mlme_down+0x70/0xc0 [cfg80211]
[<f8264de1>] __cfg80211_disconnect+0x1b1/0x1d0 [cfg80211]
To fix the problem disconnect from any associated network before
suspend. User space is responsible to establish connection again
after resume. This basically need to be done by user space anyway,
because associated stations can go away during suspend (for example
NetworkManager disconnects on suspend and connect on resume by default).
Patch also handle situation when driver refuse to suspend with wowlan
configured and try to suspend again without it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_CMD_UPDATE_FT_IES to support update of FT IEs to the WLAN
driver and NL80211_CMD_FT_EVENT to send FT events from the WLAN driver.
This will carry the target AP's MAC address along with the relevant
Information Elements. This event is used to report received FT IEs
(MDIE, FTIE, RSN IE, TIE, RICIE). These changes allow FT to be supported
with drivers that use an internal SME instead of user space option (like
FT implementation in wpa_supplicant with mac80211-based drivers).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's not useful to specify a 0 keepalive interval, this
would send too much data. Prohibit this to also avoid
device issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_mlme_assoc() has grown far too many arguments,
make the caller build almost all of the driver struct
and pass that to the function instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing it's sometimes useful to be able to
override certain VHT capability advertisement,
add the ability to do that in cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is the sort of thing gcc's LTO could do, but since
we don't have that yet we can also do it manually. The
advantage is reduced code, both source and binary, e.g.
on x86-64
text data bss dec hex filename
442825 56230 776 499831 7a077 cfg80211.ko (before)
441585 56230 776 498591 79b9f cfg80211.ko (after)
a reduction of ~1k.
But in order to not complicate the code move only those
functions that are simple wrappers, not those that have
functionality of their own.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add back the channel width and extended capability data
to wiphy information if split information is supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add back the previously removed TCP WoWLAN information,
but only if userspace is prepared to deal with large
wiphy capability data dumps.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If userspace is updated to deal with large split wiphy
information dumps, add back the radar information that
could otherwise push the data over the limit of the
netlink dump messages.
Cc: Simon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The per-wiphy information is getting large, to the point
where with more than the typical number of channels it's
too large and overflows, and userspace can't get any of
the information at all.
To address this (in a way that doesn't require making all
messages bigger) allow userspace to specify that it can
deal with wiphy information split across multiple parts
of the dump, and if it can split up the data. This also
splits up each channel separately so an arbitrary number
of channels can be supported.
Additionally, since GET_WIPHY has the same problem, add
support for filtering the wiphy dump and get information
for a single wiphy only, this allows userspace apps to
use dump in this case to retrieve all data from a single
device.
As userspace needs to know if all this this is supported,
add a global nl80211 feature set and include a bit for
this behaviour in it.
Cc: Dennis H Jensen <dennis.h.jensen@siemens.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The station change API isn't being checked properly before
drivers are called, and as a result it is difficult to see
what should be allowed and what not.
In order to comprehensively check the API parameters parse
everything first, and then have the driver call a function
(cfg80211_check_station_change()) with the additionally
information about the kind of station that is being changed;
this allows the function to make better decisions than the
old code could.
While at it, also add a few checks, particularly in mesh
and clarify the TDLS station lifetime in documentation.
To be able to reduce a few checks, ignore any flag set bits
when the mask isn't set, they shouldn't be applied then.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the ability to leave the plink_state unchanged not use a
magic -1 variable that isn't in the enum, but an explicit change
flag; reject invalid plink states or actions and move the needed
constants for plink actions to the right header file. Also
reject plink_state changes for non-mesh interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Given a device with many channels capabilities the wiphy
information can still overflow even though its size in
3.9 was reduced to 3.8 levels. For new userspace and
kernel 3.10 we're going to implement a new "split dump"
protocol that can use multiple messages per wiphy.
For now though, add a workaround to be able to send more
information to userspace. Since generic netlink doesn't
have a way to set the minimum dump size globally, and we
wouldn't really want to set it globally anyway, increase
the size only when needed, as described in the comments.
As userspace might not be prepared for large buffers, we
can only use 4k.
Also increase the size for the get_wiphy command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is another case of data increasing the size of the
wiphy information significantly with a new feature, for
now remove this as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Just like the radar information, the TCP WoWLAN capability
data can increase the wiphy information and make it too
big. Remove the TCP WoWLAN information; no driver supports
it and new userspace tools will be required as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wiphy information is getting very close to being too
much for a typical netlink dump message and adding the
radar attributes to channels and interface combinations
can push it over the limit, which means userspace gets no
information whatsoever. Therefore, remove these again for
now, no driver actually supports radar detection anyway
and a modified userspace is required as well.
We're working on a solution that will allow userspace to
request splitting the information across multiple netlink
messages, which will allow us to add this back.
Cc: Simon Wunderlich <simon.wunderlich@s2003.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
This probably is the last big pull request for wireless bits
for 3.9. Of course, I'm sure there will be a few stragglers here
and there...surely a few bug fixes as well... :-) (In fact, I see
that Johannes has already queued-up a few more for me while I was
preparing this...)
Included are a number of pulls...
For mac80211-next, Johannes says:
"The biggest change I have is undoubtedly Marco's mesh powersave
implementation. Beyond that, I have a patch from Emmanuel to modify the
DTIM period API in mac80211, scan improvements and a removal of some
previous workaround code from Stanislaw, dynamic short slot time from
Thomas and 64-bit station byte counters from Vladimir. I also made a
number of changes myself, some related to WoWLAN, some auth/deauth
improvements and most of them BSS list cleanups."
"This time, I have relatively large number of fixes in various areas of
the code (a memory leak in regulatory, an RX race in mac80211, the new
radar checking caused a P2P device problem, some mesh issues with
stations, an older bug in tracing and for kernel-doc) as well as a
number of small new features. The biggest (in the diffstat) is my work
on hidden SSID tracking."
"Please pull to get
* radar detection work from Simon
* mesh improvements from Thomas
* a connection monitoring/powersave fix from Wojciech
* TDLS-related station management work from Jouni
* VLAN crypto fixes from Michael Braun
* CCK support in minstrel_ht from Felix
* an SMPS (not SMSP, oops) related improvement in mac80211 (Emmanuel)
* some WoWLAN work from Amitkumar Karwar: pattern match offset and a
documentation fix
* some WoWLAN work from myself (TCP connection wakeup feature API)
* and a lot of VHT (and some HT) work (also from myself)
And a number of more random cleanups/fixes. I merged mac80211/master to
avoid a merge problem there."
And regarding iwlwifi-next, Johannes says:
"We continue work on our new driver, but I also have a WoWLAN and AP mode
improvement for the previous driver and a change to use threaded
interrupts to prepare us for working with non-PCIe devices."
Regarding wl12xx, Luca says:
"A few more patches intended for 3.9. Mostly some clean-ups I've been
doing to make it easier to support device-tree. Also including one bug
fix for wl12xx where the rates we advertise were wrong and an update in
the wlconf structure to support newer firmwares."
For the nfc-next bits, Samuel says:
"This is the second NFC pull request for 3.9.
We have:
- A few pn533 fixes on top of Waldemar refactorization of the driver, one of
them fixes target mode.
- A new driver for Inside Secure microread chipset. It supports two
physical layers: i2c and MEI. The MEI one depends on a patchset that's
been sent to Greg Kroah-Hartman for inclusion into the 3.9 kernel [1]. The
dependency is a KConfig one which means this code is not buildable as long
as the MEI API is not usptream."
"This 3rd NFC pull request for 3.9 contains a fix for the microread MEI
physical layer support, as the MEI bus API changed.
From the MEI code, we now pass the MEI id back to the driver probe routine,
and we also pass a name and a MEI id table through the mei_bus_driver
structure. A few renames as well like e.g. mei_bus_driver to mei_driver or
mei_bus_client to mei_device in order to be closer to the driver model
practices."
For the ath6kl bits, Kalle says:
"There's not anything special here, most of the patches are just code
cleanup. The only functional changes are using the beacon interval from user
space and fixing a crash which happens when inserting and removing the
module in a loop."
Also, I pulled the wireless tree in order to resolve some pending
merge issues. On top of that, there is a bunch of work on brcmfmac
that leads up to P2P support. Also, mwifiex, rtlwifi, and a variety
of other drivers see some basic cleanups and minor enhancements.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_net_remove is only used to remove proc entries
that under /proc/net,it's not a general function for
removing proc entries of netns. if we want to remove
some proc entries which under /proc/net/stat/, we still
need to call remove_proc_entry.
this patch use remove_proc_entry to replace proc_net_remove.
we can remove proc_net_remove after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, some modules such as bonding use proc_create
to create proc entries under /proc/net/, and other modules
such as ipv4 use proc_net_fops_create.
It looks a little chaos.this patch changes all of
proc_net_fops_create to proc_create. we can remove
proc_net_fops_create after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Larry noticed (and bisected) that commit df881293c6
"cfg80211: Pass TDLS peer's QoS/HT/VHT information during set_station"
broke secure connections. This is is the case only for drivers that
don't support TDLS, where any kind of change, even just the change of
authorized flag that is required for normal operation, was rejected
now. To fix this, remove the checks. I have some patches that will add
proper verification for all the different cases later.
Cc: Jouni Malinen <j@w1.fi>
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The information of the peer's capabilities is required for the driver
to perform TDLS Peer UAPSD operations. This information of the peer is
passed by the supplicant using NL80211_CMD_SET_STATION command. This
commit enhances the function nl80211_set_station to pass this
information of the peer to the driver in case this command is used
with the TDLS peer STA.
In addition, make the HT/VHT capability configuration handled more
consistently for other STA cases (reject both instead of just HT).
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The information of the peer's capabilities and extended capabilities are
required for the driver to perform TDLS Peer UAPSD operations and off
channel operations. This information of the peer is passed from user space
using NL80211_CMD_SET_STATION command. This commit enhances
the function nl80211_set_station to pass the capability information of
the peer to the driver.
Similarly, there may be need for capability information for other modes,
so allow this to be provided with both add_station and change_station.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In many cases, userspace may need to know which of the
802.11 extended capabilities ("Extended Capabilities
element") are implemented in the driver or device, to
include them e.g. in beacons, assoc request/response
or other frames. Add a new nl80211 attribute to hold
the extended capabilities bitmap for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When drivers or regulatory have limitations on
40, 80 or 160 MHz channels, advertise these to
userspace via nl80211. Also add a new feature
flag to let userspace know this is supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers might support 80 or 160 MHz only on some
channels for whatever reason, so allow them to disable
these channel widths. Also maintain the new flags when
regulatory bandwidth limitations would disable these
wide channels.
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new NL80211_CMD_RADAR_DETECT, which starts the Channel
Availability Check (CAC). This command will also notify the
usermode about events (CAC finished, CAC aborted, radar
detected, NOP finished).
Once radar detection has started it should continuously
monitor for radars as long as the channel is active.
This patch enables DFS for AP mode in nl80211/cfg80211.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
[remove WIPHY_FLAG_HAS_RADAR_DETECT again -- my mistake]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Intel Wireless devices are able to make a TCP connection
after suspending, sending some data and waking up when
the connection receives wakeup data (or breaks). Add the
WoWLAN configuration and feature advertising API for it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_find_vendor_ie() was checking only that the vendor IE would
fit in the remaining IEs buffer. If a corrupt includes a vendor IE
that is too small, we could potentially overrun the IEs buffer.
Fix this by checking that the vendor IE fits in the reported IE length
field and skip it otherwise.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <coelho@ti.com>
[change BUILD_BUG_ON to != 1 (from >= 2)]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If user knows the location of a wowlan pattern to be matched in
Rx packet, he can provide an offset with the pattern. This will
help drivers to ignore initial bytes and match the pattern
efficiently.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
[refactor pattern sending]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While technically the TSF isn't an IE, it can be
necessary to distinguish between the TSF from a
beacon and a probe response, in particular in
order to know the next DTIM TBTT, as not all APs
are spec compliant wrt. TSF==0 being a DTIM TBTT
and thus the DTIM count needs to be taken into
account as well.
To allow this, move the TSF into the IE struct
so it can be known whence it came.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no way scan BSS IEs can be NULL as even
if the allocation fails the frame is discarded.
Remove some code checking for this and document
that it is always non-NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, cfg80211 will copy beacon IEs from a previously
received hidden SSID beacon to a probe response entry, if
that entry is created after the beacon entry. However, if
it is the other way around, or if the beacon is updated,
such changes aren't propagated.
Fix this by tracking the relation between the probe
response and beacon BSS structs in this case.
In case drivers have private data stored in a BSS struct
and need access to such data from a beacon entry, cfg80211
now provides the hidden_beacon_bss pointer from the probe
response entry to the beacon entry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This prepares for using the spinlock instead of krefs
which is needed in the next patch to track the refs
of combined BSSes correctly.
Acked-by: Bing Zhao <bzhao@marvell.com> [mwifiex]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a driver requests a specific regulatory domain after cfg80211 already
has one, a struct ieee80211_regdomain is leaked.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/intel/e1000e/ethtool.c
drivers/net/vmxnet3/vmxnet3_drv.c
drivers/net/wireless/iwlwifi/dvm/tx.c
net/ipv6/route.c
The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.
The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.
The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.
The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of annotating with a comment, add a lockdep
annotation which also serves as documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The comment about allocating the IEs together with
the BSS struct is no longer true, remove it. Also
fix a typo in the same area.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As Thomas pointed out, cfg80211_get_mesh() is
unused and can be removed.
Cc: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of first checking if a BSS is an MBSS
and then doing the comparisons, inline it all
into the BSS comparison function. This avoids
doing the IE searches twice and is also a lot
less code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When trying to find a hidden SSID, the lookup function
is done wrong; the code is trying to combine the two
lookups into one, and as a consequence doesn't always
find the entry at all. To understand this, consider a
case where multiple BSS entries with the same channel
and BSSID exist but have different SSID length. Then
comparing against the probe response SSID length is
bound to cause problems since the hidden one might be
either zeroed out or zero-length.
To fix this we need to do two lookups for the two ways
to hide SSIDs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of duplicating the rbtree functions, pass
an argument to the compare function. This removes
the code duplication for the two searches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In per-station statistics, present 32bit counters are too small
for practical purposes - with gigabit speeds, it get overlapped
every few seconds.
Expand counters in the struct station_info to be 64-bit.
Driver can still fill only 32-bit and indicate in @filled
only bits like STATION_INFO_[TR]X_BYTES; in case driver provides
full 64-bit counter, it should also set in @filled
bit STATION_INFO_[TR]RX_BYTES64
Netlink sends both 32-bit and 64-bit counters, if present, to not
break userspace.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[change to also have 32-bit counters if driver advertises 64-bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that mac80211 no longer uses this API, remove
it completely. If anyone needs it again, we can
revert this patch of course, but mac80211 was the
only user right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When waking up from WoWLAN, it is useful to know
what triggered the wakeup. Support reporting the
wakeup reason(s) in cfg80211 (and a pass-through
in mac80211) to allow userspace to know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The warning here occasionally triggers but we haven't
found the cause yet. It's a valid warning since if it
triggers the SME state got confused, so add the SME
state to it to help narrow it down in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add API to enable drivers to implement MAC address based
access control in AP/P2P GO mode. Capable drivers advertise
this capability by setting the maximum number of MAC
addresses in such a list in wiphy->max_acl_mac_addrs.
An initial ACL may be given to the NL80211_CMD_START_AP
command and/or changed later with NL80211_CMD_SET_MAC_ACL.
Black- and whitelists are supported, but not simultaneously.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
[rewrite commit log, many cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit "cfg80211: check radar interface combinations" a regression
was introduced which might lead to NULL dereference if the argument
chan = NULL, which might happen in IBSS/wext case (and probably
others).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We do a:
sprintf(buf, " Last beacon: %ums ago",
elapsed_jiffies_msecs(bss->ts));
elapsed_jiffies_msecs() can return a 10 digit number so "buf" needs to
be 31 characters long.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The NL80211_ATTR_USE_MFP attribute was originally added for
NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more
useful) with NL80211_CMD_CONNECT, so process that attribute with the
connect command, too.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per email discussion Jouni Malinen pointed out that:
"P2P message exchanges can be executed on the current operating channel
of any operation (both P2P and non-P2P station). These can be on 5 GHz
and even on 60 GHz (so yes, you _can_ do GO Negotiation on 60 GHz).
As an example, it would be possible to receive a GO Negotiation Request
frame on a 5 GHz only radio and then to complete GO Negotiation on that
band. This can happen both when connected to a P2P group (through client
discoverability mechanism) and when connected to a legacy AP (assuming
the station receive Probe Request frame from full scan in the beginning
of P2P device discovery)."
This means that P2P messages can be sent over different radio devices.
However, these should use the same P2P device address so it should be
able to provision this from user-space. This patch adds a parameter for
this to struct vif_params which should only be used during creation of
the P2P device interface.
Cc: Jouni Malinen <j@w1.fi>
Cc: Greg Goldman <ggoldman@broadcom.com>
Cc: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[add error checking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the nl80211_mesh_power_mode enumeration which holds possible
values for the mesh power mode. These modes are unknown, active,
light sleep and deep sleep.
Add power_mode entry to the mesh config structure to hold the
user-configured default mesh power mode. This value will be used
for new peer links.
Add the dot11MeshAwakeWindowDuration value to the mesh config.
The awake window is a duration in TU describing how long the STA
will stay awake after transmitting its beacon in PS mode.
Add access routines to:
- get/set local link-specific power mode (STA)
- get remote STA's link-specific power mode (STA)
- get remote STA's non-peer power mode (STA)
- get/set default mesh power mode (mesh config)
- get/set mesh awake window duration (mesh config)
All config changes may be done at mesh runtime and take effect
immediately.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
[fix commit message line length, error handling in set station]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ranges are taken from IEEE 802.11-2012, common sense or current
implementation requirements.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since:
commit 2c60db0370
Author: Eric Dumazet <edumazet@google.com>
Date: Sun Sep 16 09:17:26 2012 +0000
net: provide a default dev->ethtool_ops
wireless core does not correctly assign ethtool_ops.
After alloc_netdev*() call, some cfg80211 drivers provide they own
ethtool_ops, but some do not. For them, wireless core provide generic
cfg80211_ethtool_ops, which is assigned in NETDEV_REGISTER notify call:
if (!dev->ethtool_ops)
dev->ethtool_ops = &cfg80211_ethtool_ops;
But after Eric's commit, dev->ethtool_ops is no longer NULL (on cfg80211
drivers without custom ethtool_ops), but points to &default_ethtool_ops.
In order to fix the problem, provide function which will overwrite
default_ethtool_ops and use it by wireless core.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1a9193185f "regulatory: code cleanup"
changed is_ht40_allowed without considering that IEEE80211_CHAN_NO_HT40 is
not just one flag, but two.
This is causing HT40- to be blocked completely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit 379b82f4c9
("regulatory: pass new regdomain to reset function")
broke the restore_regulatory_settings() function due
to a logic change. Consider this change:
- reset_regdomains(true);
- cfg80211_regdomain = cfg80211_world_regdom;
+ reset_regdomains(true, cfg80211_world_regdom);
This looks innocent enough, until you realise that the
called function (reset_regdomains) also resets the
cfg80211_world_regdom pointer, so that the old version
of the code would use the new object it pointed to and
the new version of the code uses the old object. This
lead to a double-free of this object.
Since reset_regdomains() sets it to &world_regdom, use
that directly.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Bob Copeland <me@bobcopeland.com>
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The uevent callback doesn't protect its access to
last_request, which now causes a warning since
the conversion to get_last_request(). Fix this by
allowing to use RCU protection for last_request.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following changes are invalid and should be
disallowed when a station already exists:
* supported rates changes, except for TDLS peers
* listen interval changes
* HT capability changes
Disallow them and also update a mac80211 comment
explaining how they would be racy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.
To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should not add new beacon hints even if the wiphy
is not world roaming. Without this we were always adding
a beacon hint if not world roaming for every non world
roaming wiphy interface.
Tested-by: Ben Greear <greearb@candelatech.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[fix locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be used later by other code. This has no
functional change.
Tested-by: Ben Greear <greearb@candelatech.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Regulatory beacon hints are used to help with world roaming
and as it is right now we learn from a beacon hint processed
on one wiphy to all other wiphys. The processing of beacon
hints however is scheduled and if we have a lot of interfaces
we may hit the case that we'll queue a the same beacon hint
many times until its processed.
To avoid this do a lookup on the queued up beacon hints prior
to adding a new beacon hint. If the beacon hint is removed
from the pending reg beacon hint list then it would be processed
and we'd ensure all wiphys would have learned from it, if its
on the pending reg beacon list we'd now find it prior to it
being processed.
Tested-by: Ben Greear <greearb@candelatech.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of returning an error and filling a pointer
return the pointer and an ERR_PTR value in error cases.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will allow making freq_reg_info() lock-free.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To simplify the locking and not require cfg80211_mutex
(which nl80211 uses to access the global regdomain) and
also to make it possible for drivers to access their
wiphy->regd safely, use RCU to protect these pointers.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assigning after calling the function do
it inside the function. This will later avoid a
period of time where the pointer is NULL.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel bandwidth handling isn't really quite right,
it assumes that a 40 MHz channel is really two 20 MHz
channels, which isn't strictly true. This is the way the
regulatory database handling is defined right now though
so remove the logic to handle other channel widths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a bug with the world regulatory domain, it
can be updated any time which is different from all
other regdomains that can only be updated once after
a request for them. Fix this by adding a check for
"processed" to the reg_is_valid_request() function
and clear that when doing a request.
While looking at this I also found another locking
bug, last_request is protected by the reg_mutex not
the cfg80211_mutex so the code in nl80211 is racy.
Remove that code as it only tries to prevent an
allocation in an error case, which isn't necessary.
Then the function can also become static and locking
in nl80211 can have a smaller scope.
Also change __set_regdom() to do the checks earlier
and not different for world/other regdomains.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wiphy_apply_custom_regulatory() doesn't have to hold
the regulatory mutex as it only modifies the given
wiphy with the given regulatory domain, it doesn't
access any global regulatory data.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many places that currently check that cfg80211_mutex
is held don't actually use any data protected by it.
The functions that need to hold the cfg80211_mutex
are the ones using the cfg80211_regdomain variable,
so add the lock assertion to those and clarify this
in the comments.
The reason for this is that nl80211 uses the regdom
without being able to hold reg_mutex.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function itself has dual-purpose: it can
retrieve from a given regdomain or from the
globally installed one. Change it to have a
single purpose only: to look up from a given
regdomain. Pass the correct regdomain in the
freq_reg_info() function instead.
This also changes the locking rules for it,
no locking is required any more.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even if it never happens and is hidden behind the
debug config option, it's completely useless: the
calltrace will only show module loading.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
toupper() only modifies lower-case letters, so
the isalpha() check is redundant; remove it.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use list_splice_tail_init() and also simplify the locking.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code is a bit too BUG_ON happy, remove all
instances and while doing so make some code a bit
smarter by passing the right pointer instead of
indices into arrays.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is pretty much useless since get_wiphy_idx()
always returns true since it's always called with
a valid wiphy pointer.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>