Modules such as nouveau.ko and i915.ko have a link time dependency on
acpi_lid_open(), and due to its use of acpi_bus_register_driver(),
the button.ko module that provides it is only loadable when booted in
ACPI mode. However, the ACPI button driver can be built into the core
kernel as well, in which case the dependency can always be satisfied,
and the dependent modules can be loaded regardless of whether the
system was booted in ACPI mode or not.
So let's fix this asymmetry by making the ACPI button driver loadable
as a module even if not booted in ACPI mode, so it can provide the
acpi_lid_open() symbol in the same way as when built into the kernel.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[ rjw: Minor adjustments of comments, whitespace and names. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes the behavior where we return error if there are no valid PCC
subspace for a given performance domain.
The ACPI spec does not mandate the use PCC, so it is possible to have
platforms where a PCC subspace may not be present, so we need to check
for a valid PCC subspace ID only if the register is a PCC register.
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPPC V3 introduces two new entries to make it easier to convert between
abstract processor performance and frequency. The two new entries are
lowest frequency and nominal frequency. These are the frequencies
corresponding to lowest and nominal abstract performance.
Add support to read the new entries and populate them as part of the
CPPC performance capabilities which can be used by cpufreq drivers
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
WDAT table on Lenovo Z50-70 is using RTC SRAM (ports 0x70 and 0x71) to
store state of the timer. This conflicts with Linux RTC driver
(rtc-cmos.c) who fails to reserve those ports for itself preventing RTC
from functioning. In addition the WDAT table seems not to be fully
functional because it does not reset the system when the watchdog times
out.
On this system iTCO_wdt works just fine so we simply prefer to use it
instead of WDAT. This makes RTC working again and also results working
watchdog via iTCO_wdt.
Reported-by: Peter Milley <pbmilley@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199033
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Per the PCI Firmware spec r3.2, sec 4.5, an ACPI-based OS should use _OSC
to request control of Latency Tolerance Reporting (LTR) before using it.
Request control of LTR, and if the platform does not grant control, don't
use it.
N.B. If the hardware supports LTR and the ASPM L1.2 substate but the BIOS
doesn't support LTR in _OSC, we previously would enable ASPM L1.2. This
patch will prevent us from enabling ASPM L1.2 in that case. It does not
prevent us from enabling PCI-PM L1.2, since that doesn't depend on LTR.
See PCIe r40, sec 5.5.1, for the L1 PM substate entry conditions.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
At least on one Dell system the PNP motherboard resources device
includes resources used by WDAT table. Since PNP gets initialized before
WDAT it results following error and no watchdog:
platform wdat_wdt: failed to claim resource 3: [io 0x046a-0x046c]
ACPI: watchdog: Device creation failed: -16
Now, the PNP system driver is already accustomed with the situation that
it cannot reserve all those motherboard resources because drivers using
those might have reserved them already. In addition putting WDAT table
resources under motherboard resources device makes sense in general.
Fix this by initializing WDAT right before PNP. This allows WDAT to
reserve all its resources and still keeps PNP system driver happy.
Reported-by: Shubhrata.Priyadarsh@dell.com
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ThinkPad X1 Tablet(2016) is reported to have issues with
the Low Power S0 Idle _DSM interface and since this machine
model generally can do ACPI S3 just fine, and user would
like to use S3 as default sleep model, add a blacklist
entry to disable that interface for ThinkPad X1 Tablet(2016).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199057
Reported-and-tested-by: Robin Lee <robinlee.sysu@gmail.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEhRJncuj2BJSl0Jf3sN6d1ii/Ey8FAlrPnM8ACgkQsN6d1ii/
Ey9Kzwf/eQVb6zzn7FDHAb6pLaZ5i2xi2xohsKmhAVQIEa94rZ3mLoRegtnIfyjO
RcjjSAzHSZO9NQgNA2ALdu6bBdzu4/ywQEQCnY2Gqxp0ocG/+k3p/FqLHZGdcqPo
e3gpcVxHSFWUCCGm1t3umI25driqrUq4xa6UFi2IB4djDvTrK/JsSygKx6GiVujL
2eV7v7rgqaaVZQyo8iOd+LlWuKZewKLfnALUDC21X5J2HmvfoyTdn85kldzbiIsG
YR7mcfgAtAVTyCfgXI3eqAGpRFEyqR4ga87oahdV3/iW+4wreh4hm2Xd/IETXklv
Epxyet8IlMB9886PuZhZqgnW6o1RDA==
=z3bP
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"A few fixes of Xen related core code and drivers"
* tag 'for-linus-4.17-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/pvh: Indicate XENFEAT_linux_rsdp_unrestricted to Xen
xen/acpi: off by one in read_acpi_id()
xen/acpi: upload _PSD info for non Dom0 CPUs too
x86/xen: Delay get_cpu_cap until stack canary is established
xen: xenbus_dev_frontend: Verify body of XS_TRANSACTION_END
xen: xenbus: Catch closing of non existent transactions
xen: xenbus_dev_frontend: Fix XS_TRANSACTION_END handling
These updates come with:
- OF_IOMMU support for the Rockchip iommu driver so that it can
use generic DT bindings
- Rework of locking in the AMD IOMMU interrupt remapping code to
make it work better in RT kernels
- Support for improved iotlb flushing in the AMD IOMMU driver
- Support for 52-bit physical and virtual addressing in the
ARM-SMMU
- Various other small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJazi2BAAoJECvwRC2XARrjYVwP/AyXK7CjRvaiHFopIUO0WpwY
V3GiKrODtSNHqPSKuFnqIssIhxZPw/SKFz6E/pe08pZ/pxHYTxeTL78Wz7D1+4Sp
n0YokSM5qLb660OTQVnyKNCku8cEMCb9hkQ/75SFgwcILQYF93cZBDIdBn93OKVO
6xAOE+tqd8Daulnk0YpdiCTFTJPzYHPl6B7scoUav26uaKxWeMJxeYe+EXC+4WQG
U1u/jDiVXyllzGgRqqfrmO4L2acmsK8HL97hD4+m1URJKDlb8ho6xwaRThFZWqXS
SbrYnvH0ruWGrLiQKmVUssw8FqbcXCzq3236g2O8jE4jqWSm70twg+q31iMjwD7v
bwsJGMkk7aLrquv9Zpaylpf8tRECk5bjhTFC2zB0pdum5XLx47j0IHKWMLPYhkCz
E0pBefvuhoSTbt/5X0urSRzH2Hk4ljEsM+QjlfH8SN3ALTljFjay607wbxC7t35M
LEL5AuNsDDBddoJIi9D13CdJEZa4lps8dbpB8m40lQVvmiLPLcKraaG0RfKQ397T
wsxhsDOQYM2FCwfUP3n8RTsMKRIp/UVkKY+2G7AsKofciSeulK6nDbrV7jFnitx4
vTxbRgpNejJpqzKZG/W9lCGWk1BhmQK/Cbu6JW5IA4+ew9omWkFp61U6rtc645Te
6cNEYBiMz/RZIiC2b18J
=kte5
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- OF_IOMMU support for the Rockchip iommu driver so that it can use
generic DT bindings
- rework of locking in the AMD IOMMU interrupt remapping code to make
it work better in RT kernels
- support for improved iotlb flushing in the AMD IOMMU driver
- support for 52-bit physical and virtual addressing in the ARM-SMMU
- various other small fixes and cleanups
* tag 'iommu-updates-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (53 commits)
iommu/io-pgtable-arm: Avoid warning with 32-bit phys_addr_t
iommu/rockchip: Support sharing IOMMU between masters
iommu/rockchip: Add runtime PM support
iommu/rockchip: Fix error handling in init
iommu/rockchip: Use OF_IOMMU to attach devices automatically
iommu/rockchip: Use IOMMU device for dma mapping operations
dt-bindings: iommu/rockchip: Add clock property
iommu/rockchip: Control clocks needed to access the IOMMU
iommu/rockchip: Fix TLB flush of secondary IOMMUs
iommu/rockchip: Use iopoll helpers to wait for hardware
iommu/rockchip: Fix error handling in attach
iommu/rockchip: Request irqs in rk_iommu_probe()
iommu/rockchip: Fix error handling in probe
iommu/rockchip: Prohibit unbind and remove
iommu/amd: Return proper error code in irq_remapping_alloc()
iommu/amd: Make amd_iommu_devtable_lock a spin_lock
iommu/amd: Drop the lock while allocating new irq remap table
iommu/amd: Factor out setting the remap table for a devid
iommu/amd: Use `table' instead `irt' as variable name in amd_iommu_update_ga()
iommu/amd: Remove the special case from alloc_irq_table()
...
* A rework of the filesytem-dax implementation provides for detection of
unmap operations (truncate / hole punch) colliding with in-progress
device-DMA. A fix for these collisions remains a work-in-progress
pending resolution of truncate latency and starvation regressions.
* The of_pmem driver expands the users of libnvdimm outside of x86 and
ACPI to describe an implementation of persistent memory on PowerPC with
Open Firmware / Device tree.
* Address Range Scrub (ARS) handling is completely rewritten to account for
the fact that ARS may run for 100s of seconds and there is no platform
defined way to cancel it. ARS will now no longer block namespace
initialization.
* The NVDIMM Namespace Label implementation is updated to handle label
areas as small as 1K, down from 128K.
* Miscellaneous cleanups and updates to unit test infrastructure.
-----BEGIN PGP SIGNATURE-----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=acZQ
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This cycle was was not something I ever want to repeat as there were
several late changes that have only now just settled.
Half of the branch up to commit d2c997c0f1 ("fs, dax: use
page->mapping to warn...") have been in -next for several releases.
The of_pmem driver and the address range scrub rework were late
arrivals, and the dax work was scaled back at the last moment.
The of_pmem driver missed a previous merge window due to an oversight.
A sense of obligation to rectify that miss is why it is included for
4.17. It has acks from PowerPC folks. Stephen reported a build failure
that only occurs when merging it with your latest tree, for now I have
fixed that up by disabling modular builds of of_pmem. A test merge
with your tree has received a build success report from the 0day robot
over 156 configs.
An initial version of the ARS rework was submitted before the merge
window. It is self contained to libnvdimm, a net code reduction, and
passing all unit tests.
The filesystem-dax changes are based on the wait_var_event()
functionality from tip/sched/core. However, late review feedback
showed that those changes regressed truncate performance to a large
degree. The branch was rewound to drop the truncate behavior change
and now only includes preparation patches and cleanups (with full acks
and reviews). The finalization of this dax-dma-vs-trnucate work will
need to wait for 4.18.
Summary:
- A rework of the filesytem-dax implementation provides for detection
of unmap operations (truncate / hole punch) colliding with
in-progress device-DMA. A fix for these collisions remains a
work-in-progress pending resolution of truncate latency and
starvation regressions.
- The of_pmem driver expands the users of libnvdimm outside of x86
and ACPI to describe an implementation of persistent memory on
PowerPC with Open Firmware / Device tree.
- Address Range Scrub (ARS) handling is completely rewritten to
account for the fact that ARS may run for 100s of seconds and there
is no platform defined way to cancel it. ARS will now no longer
block namespace initialization.
- The NVDIMM Namespace Label implementation is updated to handle
label areas as small as 1K, down from 128K.
- Miscellaneous cleanups and updates to unit test infrastructure"
* tag 'libnvdimm-for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (39 commits)
libnvdimm, of_pmem: workaround OF_NUMA=n build error
nfit, address-range-scrub: add module option to skip initial ars
nfit, address-range-scrub: rework and simplify ARS state machine
nfit, address-range-scrub: determine one platform max_ars value
powerpc/powernv: Create platform devs for nvdimm buses
doc/devicetree: Persistent memory region bindings
libnvdimm: Add device-tree based driver
libnvdimm: Add of_node to region and bus descriptors
libnvdimm, region: quiet region probe
libnvdimm, namespace: use a safe lookup for dimm device name
libnvdimm, dimm: fix dpa reservation vs uninitialized label area
libnvdimm, testing: update the default smart ctrl_temperature
libnvdimm, testing: Add emulation for smart injection commands
nfit, address-range-scrub: introduce nfit_spa->ars_state
libnvdimm: add an api to cast a 'struct nd_region' to its 'struct device'
nfit, address-range-scrub: fix scrub in-progress reporting
dax, dm: allow device-mapper to operate without dax support
dax: introduce CONFIG_DAX_DRIVER
fs, dax: use page->mapping to warn if truncate collides with a busy page
ext2, dax: introduce ext2_dax_aops
...
After attempting to quickly retrieve known errors the kernel proceeds to
kick off a long running ARS. Add a module option to disable this
behavior at initialization time, or at new region discovery time.
Otherwise, ARS can be started manually regardless of the state of this
setting.
Co-developed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ARS is an operation that can take 10s to 100s of seconds to find media
errors that should rarely be present. If the platform crashes due to
media errors in persistent memory, the expectation is that the BIOS will
report those known errors in a 'short' ARS request.
A 'short' ARS request asks platform firmware to return an ARS payload
with all known errors, but without issuing a 'long' scrub. At driver
init a short request is issued to all PMEM ranges before registering
regions. Then, in the background, a long ARS is scheduled for each
region.
The ARS implementation is simplified to centralize ARS completion work
in the ars_complete() helper. The timeout is removed since there is no
facility to cancel ARS, and this otherwise arranges for system init to
never be blocked waiting for a 'long' ARS. The ars_state flags are used
to coordinate ARS requests from driver init, ARS requests from
userspace, and ARS requests in response to media error notifications.
Given that there is no notification of ARS completion the implementation
still needs to poll. It backs off exponentially to a maximum poll period
of 30 minutes.
Suggested-by: Toshi Kani <toshi.kani@hpe.com>
Co-developed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
acpi_nfit_query_poison() is awkward in that it requires an nfit_spa
argument in order to determine what max_ars value to use. Instead probe
for the minimum max_ars across all scrub-capable ranges in the system
and drop the nfit_spa argument.
This enables a larger rework / simplification of the ARS state machine
whereby the status can be retrieved once and then iterated over all
address ranges to reap completions.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
-----BEGIN PGP SIGNATURE-----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=T++R
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- move pci_uevent_ers() out of pci.h (Michael Ellerman)
- skip ASPM common clock warning if BIOS already configured it (Sinan
Kaya)
- fix ASPM Coverity warning about threshold_ns (Gustavo A. R. Silva)
- remove last user of pci_get_bus_and_slot() and the function itself
(Sinan Kaya)
- add decoding for 16 GT/s link speed (Jay Fang)
- add interfaces to get max link speed and width (Tal Gilboa)
- add pcie_bandwidth_capable() to compute max supported link bandwidth
(Tal Gilboa)
- add pcie_bandwidth_available() to compute bandwidth available to
device (Tal Gilboa)
- add pcie_print_link_status() to log link speed and whether it's
limited (Tal Gilboa)
- use PCI core interfaces to report when device performance may be
limited by its slot instead of doing it in each driver (Tal Gilboa)
- fix possible cpqphp NULL pointer dereference (Shawn Lin)
- rescan more of the hierarchy on ACPI hotplug to fix Thunderbolt/xHCI
hotplug (Mika Westerberg)
- add support for PCI I/O port space that's neither directly accessible
via CPU in/out instructions nor directly mapped into CPU physical
memory space. This is fairly intrusive and includes minor changes to
interfaces used for I/O space on most platforms (Zhichang Yuan, John
Garry)
- add support for HiSilicon Hip06/Hip07 LPC I/O space (Zhichang Yuan,
John Garry)
- use PCI_EXP_DEVCTL2_COMP_TIMEOUT in rapidio/tsi721 (Bjorn Helgaas)
- remove possible NULL pointer dereference in of_pci_bus_find_domain_nr()
(Shawn Lin)
- report quirk timings with dev_info (Bjorn Helgaas)
- report quirks that take longer than 10ms (Bjorn Helgaas)
- add and use Altera Vendor ID (Johannes Thumshirn)
- tidy Makefiles and comments (Bjorn Helgaas)
- don't set up INTx if MSI or MSI-X is enabled to align cris, frv,
ia64, and mn10300 with x86 (Bjorn Helgaas)
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
- use generic pci_mmap_resource_range() instead of powerpc and xtensa
arch-specific versions (David Woodhouse)
- support arbitrary PCI host bridge offsets on sparc (Yinghai Lu)
- remove System and Video ROM reservations on sparc (Bjorn Helgaas)
- probe for device reset support during enumeration instead of runtime
(Bjorn Helgaas)
- add ACS quirk for Ampere (née APM) root ports (Feng Kan)
- add function 1 DMA alias quirk for Marvell 88SE9220 (Thomas
Vincent-Cross)
- protect device restore with device lock (Sinan Kaya)
- handle failure of FLR gracefully (Sinan Kaya)
- handle CRS (config retry status) after device resets (Sinan Kaya)
- skip various config reads for SR-IOV VFs as an optimization
(KarimAllah Ahmed)
- consolidate VPD code in vpd.c (Bjorn Helgaas)
- add Tegra dependency on PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
- add DT support for R-Car r8a7743 (Biju Das)
- fix a PCI_EJECT vs PCI_BUS_RELATIONS race condition in Hyper-V host
bridge driver that causes a general protection fault (Dexuan Cui)
- fix Hyper-V host bridge hang in MSI setup on 1-vCPU VMs with SR-IOV
(Dexuan Cui)
- fix Hyper-V host bridge hang when ejecting a VF before setting up MSI
(Dexuan Cui)
- make several structures static (Fengguang Wu)
- increase number of MSI IRQs supported by Synopsys DesignWare bridges
from 32 to 256 (Gustavo Pimentel)
- implemented multiplexed IRQ domain API and remove obsolete MSI IRQ
API from DesignWare drivers (Gustavo Pimentel)
- add Tegra power management support (Manikanta Maddireddy)
- add Tegra loadable module support (Manikanta Maddireddy)
- handle 64-bit BARs correctly in endpoint support (Niklas Cassel)
- support optional regulator for HiSilicon STB (Shawn Guo)
- use regulator bulk API for Qualcomm apq8064 (Srinivas Kandagatla)
- support power supplies for Qualcomm msm8996 (Srinivas Kandagatla)
* tag 'pci-v4.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (123 commits)
MAINTAINERS: Add John Garry as maintainer for HiSilicon LPC driver
HISI LPC: Add ACPI support
ACPI / scan: Do not enumerate Indirect IO host children
ACPI / scan: Rename acpi_is_serial_bus_slave() for more general use
HISI LPC: Support the LPC host on Hip06/Hip07 with DT bindings
of: Add missing I/O range exception for indirect-IO devices
PCI: Apply the new generic I/O management on PCI IO hosts
PCI: Add fwnode handler as input param of pci_register_io_range()
PCI: Remove __weak tag from pci_register_io_range()
MAINTAINERS: Add missing /drivers/pci/cadence directory entry
fm10k: Report PCIe link properties with pcie_print_link_status()
net/mlx5e: Use pcie_bandwidth_available() to compute bandwidth
net/mlx5: Report PCIe link properties with pcie_print_link_status()
net/mlx4_core: Report PCIe link properties with pcie_print_link_status()
PCI: Add pcie_print_link_status() to log link speed and whether it's limited
PCI: Add pcie_bandwidth_available() to compute bandwidth available to device
misc: pci_endpoint_test: Handle 64-bit BARs properly
PCI: designware-ep: Make dw_pcie_ep_reset_bar() handle 64-bit BARs properly
PCI: endpoint: Make sure that BAR_5 does not have 64-bit flag set when clearing
PCI: endpoint: Make epc->ops->clear_bar()/pci_epc_clear_bar() take struct *epf_bar
...
In preparation for re-working the ARS implementation to better handle
short vs long ARS runs, introduce nfit_spa->ars_state. For now this just
replaces the nfit_spa->ars_required bit-field/flag, but going forward it
will be used to track ARS completion and make short vs long ARS
requests.
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* misc fixes
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEzv7L6UO9uDPlPSfHEsHwGGHeVUoFAlrDZ6EACgkQEsHwGGHe
VUpWWA//RG9WqqdXxPa05TxiRFWMiNSH/HSGJQZsc3K7xm2TEGVdDv5thYsxXCaW
kA0oiUJA3zd62HeUIWMeGypm+hLM8T73836aIKcfxMduxQ6DR9nk51IV4RmHsLvT
rd4bUsrjCov6spapqS265LOxZVnpKvxZv0NVTj6pIk0pkeghWMZh63vZtrxVkLsS
6dHsdIDBr0fMhcFBVQ67SEDpMIyMAqziPOP9sv6NNElG4Q93RnZr6KYvQdE32Iev
Z6lIUU/sjVJEuhgp6FjJrhvjc+FmGJGERsFqo3Z8RT9P26Cj3wq0ov8IY/KSBazG
mfJFGbL+O3lppGKjjuAwMGr4R3fZMLQpgLxdYe7VNvOHB9ea7732q9MDGiNkN/u7
z8o+dtvmPWr0Y1ir8te+7LnSQXIAwxMkKP/lMStzzuFUETQDd0RWr7GAKlbrgPOU
+DhiQRPBFS7qpslA7BdqV6Ybr3nhDVZciDYWsvNpDMwdem05TxlFwC5l/BzP9NtM
FmQ3B0rQ5we6gib6UZWUjW3BH9wUgFUpu/WXKJl1unMHwYNe3CvdM8yD5W7mUylh
6SVYAmkZyuJ1Du40+YMeimroe77XV60IqoUFNEzMSFeB4/GxMG6+u2gUqNuTpHpZ
aMmCRj9DxWGxZyDsTc49An0X/JbVyIE/Aq6heMTYScgBvCaD1VE=
=K89j
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"Noteworthy is the NVDIMM support:
- NVDIMM support to EDAC (Tony Luck)
- misc fixes"
* tag 'edac_for_4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, sb_edac: Remove variable length array usage
EDAC, skx_edac: Detect non-volatile DIMMs
firmware, DMI: Add function to look up a handle and return DIMM size
acpi, nfit: Add function to look up nvdimm device and provide SMBIOS handle
EDAC: Add new memory type for non-volatile DIMMs
EDAC: Drop duplicated array of strings for memory type names
EDAC, layerscape: Allow building for LS1021A
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
Nothing particularly stands out here, probably because people were tied
up with spectre/meltdown stuff last time around. Still, the main pieces
are:
- Rework of our CPU features framework so that we can whitelist CPUs that
don't require kpti even in a heterogeneous system
- Support for the IDC/DIC architecture extensions, which allow us to elide
instruction and data cache maintenance when writing out instructions
- Removal of the large memory model which resulted in suboptimal codegen
by the compiler and increased the use of literal pools, which could
potentially be used as ROP gadgets since they are mapped as executable
- Rework of forced signal delivery so that the siginfo_t is well-formed
and handling of show_unhandled_signals is consolidated and made
consistent between different fault types
- More siginfo cleanup based on the initial patches from Eric Biederman
- Workaround for Cortex-A55 erratum #1024718
- Some small ACPI IORT updates and cleanups from Lorenzo Pieralisi
- Misc cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJaw1TCAAoJELescNyEwWM0gyQIAJVMK4QveBW+LwF96NYdZo16
p90Aa+nqKelh/s93govQArDMv1gxyuXdFlQZVOGPQHfqpz6RhJWmBA2tFsUbQrUc
OBcioPrRihqTmKBe+1r1XORwZxkVX6GGmCn0LYpPR7I3TjxXZpvxqaxGxiUvHkci
yVxWlDTyN/7eL3akhCpCDagN3Fxwk3QnJLqE3fxOFMlY7NvQcmUxcITiUl/s469q
xK6SWH9SRH1JK8jTHPitwUBiU//3FfCqSI9HLEdDIDoTuPcVM8UetWvi4QzrzJL1
UYg8lmU0CXNmflDzZJDaMf+qFApOrGxR0YVPpBzlQvxe0JIY69g48f+JzDPz8nc=
=+gNa
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Nothing particularly stands out here, probably because people were
tied up with spectre/meltdown stuff last time around. Still, the main
pieces are:
- Rework of our CPU features framework so that we can whitelist CPUs
that don't require kpti even in a heterogeneous system
- Support for the IDC/DIC architecture extensions, which allow us to
elide instruction and data cache maintenance when writing out
instructions
- Removal of the large memory model which resulted in suboptimal
codegen by the compiler and increased the use of literal pools,
which could potentially be used as ROP gadgets since they are
mapped as executable
- Rework of forced signal delivery so that the siginfo_t is
well-formed and handling of show_unhandled_signals is consolidated
and made consistent between different fault types
- More siginfo cleanup based on the initial patches from Eric
Biederman
- Workaround for Cortex-A55 erratum #1024718
- Some small ACPI IORT updates and cleanups from Lorenzo Pieralisi
- Misc cleanups and non-critical fixes"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (70 commits)
arm64: uaccess: Fix omissions from usercopy whitelist
arm64: fpsimd: Split cpu field out from struct fpsimd_state
arm64: tlbflush: avoid writing RES0 bits
arm64: cmpxchg: Include linux/compiler.h in asm/cmpxchg.h
arm64: move percpu cmpxchg implementation from cmpxchg.h to percpu.h
arm64: cmpxchg: Include build_bug.h instead of bug.h for BUILD_BUG
arm64: lse: Include compiler_types.h and export.h for out-of-line LL/SC
arm64: fpsimd: include <linux/init.h> in fpsimd.h
drivers/perf: arm_pmu_platform: do not warn about affinity on uniprocessor
perf: arm_spe: include linux/vmalloc.h for vmap()
Revert "arm64: Revert L1_CACHE_SHIFT back to 6 (64-byte cache line size)"
arm64: cpufeature: Avoid warnings due to unused symbols
arm64: Add work around for Arm Cortex-A55 Erratum 1024718
arm64: Delay enabling hardware DBM feature
arm64: Add MIDR encoding for Arm Cortex-A55 and Cortex-A35
arm64: capabilities: Handle shared entries
arm64: capabilities: Add support for checks based on a list of MIDRs
arm64: Add helpers for checking CPU MIDR against a range
arm64: capabilities: Clean up midr range helpers
arm64: capabilities: Change scope of VHE to Boot CPU feature
...
- move pcieport_if.h to drivers/pci/pcie/ to encapsulate it (Frederick
Lawler)
- merge pcieport_if.h into portdrv.h (Bjorn Helgaas)
- move workaround for BIOS PME issue from portdrv to PCI core (Bjorn
Helgaas)
- completely disable portdrv with "pcie_ports=compat" (Bjorn Helgaas)
- remove portdrv link order dependency (Bjorn Helgaas)
- remove support for unused VC portdrv service (Bjorn Helgaas)
- simplify portdrv feature permission checking (Bjorn Helgaas)
- remove "pcie_hp=nomsi" parameter (use "pci=nomsi" instead) (Bjorn
Helgaas)
- remove unnecessary "pcie_ports=auto" parameter (Bjorn Helgaas)
- use cached AER capability offset (Frederick Lawler)
- don't enable DPC if BIOS hasn't granted AER control (Mika Westerberg)
- rename pcie-dpc.c to dpc.c (Bjorn Helgaas)
* pci/portdrv:
PCI/DPC: Rename from pcie-dpc.c to dpc.c
PCI/DPC: Do not enable DPC if AER control is not allowed by the BIOS
PCI/AER: Use cached AER Capability offset
PCI/portdrv: Rename and reverse sense of pcie_ports_auto
PCI/portdrv: Encapsulate pcie_ports_auto inside the port driver
PCI/portdrv: Remove unnecessary "pcie_ports=auto" parameter
PCI/portdrv: Remove "pcie_hp=nomsi" kernel parameter
PCI/portdrv: Remove unnecessary include of <linux/pci-aspm.h>
PCI/portdrv: Simplify PCIe feature permission checking
PCI/portdrv: Remove unused PCIE_PORT_SERVICE_VC
PCI/portdrv: Remove pcie_port_bus_type link order dependency
PCI/portdrv: Disable port driver in compat mode
PCI/PM: Clear PCIe PME Status bit for Root Complex Event Collectors
PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver
PCI/PM: Move pcie_clear_root_pme_status() to core
PCI/portdrv: Merge pcieport_if.h into portdrv.h
PCI/portdrv: Move pcieport_if.h to drivers/pci/pcie/
Conflicts:
drivers/pci/pcie/Makefile
drivers/pci/pcie/portdrv.h
Through the logical PIO framework, systems which otherwise have no IO space
access to legacy ISA/LPC devices may access these devices through so-called
"indirect IO" method. In this, IO space accesses for non-PCI hosts are
redirected to a host LLDD to manually generate the IO space (bus) accesses.
Hosts are able to register a region in logical PIO space to map to its bus
address range.
Indirect IO child devices have an associated host-specific bus address.
Special translation is required to map between a logical PIO address for a
device and its host bus address.
Since in the ACPI tables the child device IO resources would be the
host-specific values, it is required the ACPI scan code should not
enumerate these devices, and that this should be the responsibility of the
host driver so that it can "fixup" the resources so that they map to the
appropriate logical PIO addresses.
To avoid enumerating these child devices, add a check from
acpi_device_enumeration_by_parent() as to whether the parent for a device
is a member of a known list of "indirect IO" hosts. For now, the HiSilicon
LPC host controller ID is added.
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the ACPI scan has special handling for serial bus slaves, in that
it makes it the responsibility of the slave device's parent to enumerate
the device.
To support other types of slave devices which require the same special
handling but where the bus is not strictly a serial bus, such as devices on
the HiSilicon LPC controller bus, rename acpi_is_serial_bus_slave() to
acpi_device_enumeration_by_parent(), so that the name can fit the wider
purpose.
Also rename the associated device flag acpi_device_flags.serial_bus_slave
to .enumeration_by_parent.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In preparation for having the PCI MMIO helpers use the new generic I/O
space management (logical PIO) we need to add the fwnode handler as an
extra input parameter.
Changes the signature of pci_register_io_range() and its callers as
needed.
Tested-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
There is a small window whereby ARS scan requests can schedule work that
userspace will miss when polling scrub_show. Hold the init_mutex lock
over calls to report the status to close this potential escape. Also,
make sure that requests to cancel the ARS workqueue are treated as an
idle event.
Cc: <stable@vger.kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Fixes: 37b137ff8c ("nfit, libnvdimm: allow an ARS scrub...")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the
PM core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI
if both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and
drop it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of
DT bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core
(Viresh Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian,
Viresh Kumar).
- Drop memory allocation error messages from a few places in
cpufreq and cpuildle drivers (Markus Elfring).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6JC2
-----END PGP SIGNATURE-----
Merge tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update the cpuidle poll state definition to reduce excessive
energy usage related to it, add new CPU ID to the RAPL power capping
driver, update the ACPI system suspend code to handle some special
cases better, extend the PM core's device links code slightly, add new
sysfs attribute for better suspend-to-idle diagnostics and easier
hibernation handling, update power management tools and clean up
cpufreq quite a bit.
Specifics:
- Modify the cpuidle poll state implementation to prevent CPUs from
staying in the loop in there for excessive times (Rafael Wysocki).
- Add Intel Cannon Lake chips support to the RAPL power capping
driver (Joe Konno).
- Add reference counting to the device links handling code in the PM
core (Lukas Wunner).
- Avoid reconfiguring GPEs on suspend-to-idle in the ACPI system
suspend code (Rafael Wysocki).
- Allow devices to be put into deeper low-power states via ACPI if
both _SxD and _SxW are missing (Daniel Drake).
- Reorganize the core ACPI suspend-to-idle wakeup code to avoid a
keyboard wakeup issue on Asus UX331UA (Chris Chiu).
- Prevent the PCMCIA library code from aborting suspend-to-idle due
to noirq suspend failures resulting from incorrect assumptions
(Rafael Wysocki).
- Add coupled cpuidle supprt to the Exynos3250 platform (Marek
Szyprowski).
- Add new sysfs file to make it easier to specify the image storage
location during hibernation (Mario Limonciello).
- Add sysfs files for collecting suspend-to-idle usage and time
statistics for CPU idle states (Rafael Wysocki).
- Update the pm-graph utilities (Todd Brandt).
- Reduce the kernel log noise related to reporting Low-power Idle
constraings by the ACPI system suspend code (Rafael Wysocki).
- Make it easier to distinguish dedicated wakeup IRQs in the
/proc/interrupts output (Tony Lindgren).
- Add the frequency table validation in cpufreq to the core and drop
it from a number of cpufreq drivers (Viresh Kumar).
- Drop "cooling-{min|max}-level" for CPU nodes from a couple of DT
bindings (Viresh Kumar).
- Clean up the CPU online error code path in the cpufreq core (Viresh
Kumar).
- Fix assorted issues in the SCPI, CPPC, mediatek and tegra186
cpufreq drivers (Arnd Bergmann, Chunyu Hu, George Cherian, Viresh
Kumar).
- Drop memory allocation error messages from a few places in cpufreq
and cpuildle drivers (Markus Elfring)"
* tag 'pm-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (56 commits)
ACPI / PM: Fix keyboard wakeup from suspend-to-idle on ASUS UX331UA
cpufreq: CPPC: Use transition_delay_us depending transition_latency
PM / hibernate: Change message when writing to /sys/power/resume
PM / hibernate: Make passing hibernate offsets more friendly
cpuidle: poll_state: Avoid invoking local_clock() too often
PM: cpuidle/suspend: Add s2idle usage and time state attributes
cpuidle: Enable coupled cpuidle support on Exynos3250 platform
cpuidle: poll_state: Add time limit to poll_idle()
cpufreq: tegra186: Don't validate the frequency table twice
cpufreq: speedstep: Don't validate the frequency table twice
cpufreq: sparc: Don't validate the frequency table twice
cpufreq: sh: Don't validate the frequency table twice
cpufreq: sfi: Don't validate the frequency table twice
cpufreq: scpi: Don't validate the frequency table twice
cpufreq: sc520: Don't validate the frequency table twice
cpufreq: s3c24xx: Don't validate the frequency table twice
cpufreq: qoirq: Don't validate the frequency table twice
cpufreq: pxa: Don't validate the frequency table twice
cpufreq: ppc_cbe: Don't validate the frequency table twice
cpufreq: powernow: Don't validate the frequency table twice
...
- Update the in-kernel ACPICA code to upstream revision 20180313
including:
* Module-level AML code handling fixes and simplifications (Bob
Moore, Erik Schmauss).
* Fixes and cleanups related to messaging (Bob Moore).
* Events handling fixes related to disabling and enabling GPEs
(Erik Schmauss).
* Introduction of SPDX license identifiers and removal of license
boilerplate in multiple files (Erik Schmauss).
* Assorted fixes and cleanups (Bob Moore, Erik Schmauss, Hans
de Goede, Seunghun Han).
- Add new basic driver for the ACPI Time and Alarm Device (Rafael
Wysocki).
- Modify the ACPI battery driver to support battery thresholds on
Lenovo ThinkPads (Ognjen Galic, Colin Ian King).
- Avoid reporting battery capacity over 100 in the ACPI battery
driver in some cases (Laszlo Toth).
- Make the kernel recognize an OEM _OSI string from Dell to avoid
power management issues with NVidia GPUs in Dell platforms (Alex
Hung).
- Make the PCI IRQ management code handle missing _PRS cleanly (Alex
Hung).
- Fix uevent notifications related to device hotplut (Lee, Chun-Yi).
- Prevent the ACPI PAD driver from leaking memory (Lenny Szubowicz).
- Update the ACPI CPPC library code to include subspace IDs in the
kernel messages logged by it (George Cherian).
- Add backlight quirk for Samsung 670Z5E (Hans de Goede).
- Add the NFIT and HMAT tables to the list of ACPI tables that can
be overridden via initrd (Dan Williams).
- Fix and clean up some ACPI documentation and Kconfig help language
(Aishwarya Pant, Randy Dunlap).
- Replace license boilerplate with an SPDX license ID in the ACPI
PMIC operation region handling code (Rajmohan Mani).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=pVZ/
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to follow upstream revision
20180313 which includes fixes related to the so-called module-level
AML (mostly "if" type of statements outside of any methods) that
should improve the handling of systems that load alternative SSDTs
depending on the current configuration, for example, and event
handling fixes related to disabling and enabling GPEs on system
startup and on suspend/resume.
Moreover, the ACPICA license boilerplate is replaced with SPDX license
IDs which alone reduces the number of lines of ACPICA code in the
kernel quite a bit.
Also added is a new driver for the generic ACPI Time and Alarm Device
(TAD). At the moment it only handles the most basic capabilities of
the TAD, however.
In addition to that the ACPI battery driver is improved to handle
battery thresholds on ThinkPads, among other things, some bugs are
fixed, a new backlight quirk is added and some documentation is
updated.
Specifics:
- Update the in-kernel ACPICA code to upstream revision 20180313
including:
* Module-level AML code handling fixes and simplifications (Bob
Moore, Erik Schmauss).
* Fixes and cleanups related to messaging (Bob Moore).
* Events handling fixes related to disabling and enabling GPEs
(Erik Schmauss).
* Introduction of SPDX license identifiers and removal of license
boilerplate in multiple files (Erik Schmauss).
* Assorted fixes and cleanups (Bob Moore, Erik Schmauss, Hans de
Goede, Seunghun Han).
- Add new basic driver for the ACPI Time and Alarm Device (Rafael
Wysocki).
- Modify the ACPI battery driver to support battery thresholds on
Lenovo ThinkPads (Ognjen Galic, Colin Ian King).
- Avoid reporting battery capacity over 100 in the ACPI battery
driver in some cases (Laszlo Toth).
- Make the kernel recognize an OEM _OSI string from Dell to avoid
power management issues with NVidia GPUs in Dell platforms (Alex
Hung).
- Make the PCI IRQ management code handle missing _PRS cleanly (Alex
Hung).
- Fix uevent notifications related to device hotplut (Lee, Chun-Yi).
- Prevent the ACPI PAD driver from leaking memory (Lenny Szubowicz).
- Update the ACPI CPPC library code to include subspace IDs in the
kernel messages logged by it (George Cherian).
- Add backlight quirk for Samsung 670Z5E (Hans de Goede).
- Add the NFIT and HMAT tables to the list of ACPI tables that can be
overridden via initrd (Dan Williams).
- Fix and clean up some ACPI documentation and Kconfig help language
(Aishwarya Pant, Randy Dunlap).
- Replace license boilerplate with an SPDX license ID in the ACPI
PMIC operation region handling code (Rajmohan Mani)"
* tag 'acpi-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (39 commits)
ACPI: acpi_pad: Fix memory leak in power saving threads
ACPI / video: Add quirk to force acpi-video backlight on Samsung 670Z5E
ACPI: Add Time and Alarm Device (TAD) driver
ACPI / scan: Send change uevent with offine environmental data
ACPI / Kconfig: Update ACPI_PROCFS_POWER help text
ACPI / OSI: Add OEM _OSI strings to disable NVidia RTD3
ACPICA: Update version to 20180313
ACPICA: Cleanup/simplify module-level code support
ACPICA: Events: add a return on failure from acpi_hw_register_read
ACPICA: adding SPDX headers
ACPICA: Rename a global for clarity, no functional change
ACPICA: macros: fix ACPI_ERROR_NAMESPACE macro
ACPICA: Change a compile-time option to a runtime option
ACPICA: Remove calling of _STA from acpi_get_object_info()
ACPICA: AML Debug Object: Don't ignore output of zero-length strings
ACPICA: Fix memory leak on unusual memory leak
ACPICA: Events: Dispatch GPEs after enabling for the first time
ACPICA: Events: Add parallel GPE handling support to fix potential redundant _Exx evaluations
ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume
ACPICA: acpi: acpica: fix acpi operand cache leak in nseval.c
...
Commit 1cf03c00e7 "nfit: scrub and register regions in a workqueue"
mistakenly attempts to register a region per BLK aperture. There is
nothing to register for individual apertures as they belong as a set to
a BLK aperture group that are registered with a corresponding
DIMM-control-region. Filter them for registration to prevent some
needless devm_kzalloc() allocations.
Cc: <stable@vger.kernel.org>
Fixes: 1cf03c00e7 ("nfit: scrub and register regions in a workqueue")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle were:
- Add "Jailhouse" hypervisor support (Jan Kiszka)
- Update DeviceTree support (Ivan Gorinov)
- Improve DMI date handling (Andy Shevchenko)"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/PCI: Fix a potential regression when using dmi_get_bios_year()
firmware/dmi_scan: Uninline dmi_get_bios_year() helper
x86/devicetree: Use CPU description from Device Tree
of/Documentation: Specify local APIC ID in "reg"
MAINTAINERS: Add entry for Jailhouse
x86/jailhouse: Allow to use PCI_MMCONFIG without ACPI
x86: Consolidate PCI_MMCONFIG configs
x86: Align x86_64 PCI_MMCONFIG with 32-bit variant
x86/jailhouse: Enable PCI mmconfig access in inmates
PCI: Scan all functions when running over Jailhouse
jailhouse: Provide detection for non-x86 systems
x86/devicetree: Fix device IRQ settings in DT
x86/devicetree: Initialize device tree before using it
pci: Simplify code by using the new dmi_get_bios_year() helper
ACPI/sleep: Simplify code by using the new dmi_get_bios_year() helper
x86/pci: Simplify code by using the new dmi_get_bios_year() helper
dmi: Introduce the dmi_get_bios_year() helper function
x86/platform/quark: Re-use DEFINE_SHOW_ATTRIBUTE() macro
x86/platform/atom: Re-use DEFINE_SHOW_ATTRIBUTE() macro
* acpi-tables:
ACPI: add NFIT and HMAT to the initrd override list
* acpi-cppc:
ACPI / CPPC: Update all pr_(debug/err) messages to log the susbspace id
* acpi-pci:
ACPI / PCI: pci_link: Allow the absence of _PRS and change log level
* acpi-battery:
Revert "ACPI: battery: Add the ThinkPad "Not Charging" quirk"
ACPI: battery: do not export degraded capacity values over 100
ACPI: battery: make function __battery_hook_unregister() static
ACPI: battery: Add the ThinkPad "Not Charging" quirk
thinkpad_acpi: Add support for battery thresholds
power: add to_power_supply macro to the API
battery: Add the battery hooking API
* acpi-doc:
ACPI: sysfs: Update device object sysfs documentation
* acpi-pmic:
ACPI / PMIC: Replace license boilerplate with SPDX license identifier
* acpica: (21 commits)
ACPICA: Update version to 20180313
ACPICA: Cleanup/simplify module-level code support
ACPICA: Events: add a return on failure from acpi_hw_register_read
ACPICA: adding SPDX headers
ACPICA: Rename a global for clarity, no functional change
ACPICA: macros: fix ACPI_ERROR_NAMESPACE macro
ACPICA: Change a compile-time option to a runtime option
ACPICA: Remove calling of _STA from acpi_get_object_info()
ACPICA: AML Debug Object: Don't ignore output of zero-length strings
ACPICA: Fix memory leak on unusual memory leak
ACPICA: Events: Dispatch GPEs after enabling for the first time
ACPICA: Events: Add parallel GPE handling support to fix potential redundant _Exx evaluations
ACPICA: Events: Stop unconditionally clearing ACPI IRQs during suspend/resume
ACPICA: acpi: acpica: fix acpi operand cache leak in nseval.c
ACPICA: Update version to 20180209
ACPICA: Add option to disable Package object name resolution errors
ACPICA: Integrate package handling with module-level code
ACPICA: Revert "Fix for implicit result conversion for the To____ functions"
ACPICA: Update for some debug output. No functional change
ACPICA: Update error message, no functional change
...
This issue happens on new ASUS laptop UX331UA which has modern
standby mode (suspend-to-idle). Pressing keys on the PS2 keyboard
can't wake up the system from suspend-to-idle which is not expected.
However, pressing power button can wake up without problem.
Per the engineers of ASUS, the keypress event is routed to Embedded
Controller (EC) in standby mode. EC then signals the SCI event to
BIOS so BIOS would Notify() power button to wake up the system. It's
from BIOS perspective. What we observe here is that kernel receives
the SCI event from SCI interrupt handler which informs that the GPE
status bit belongs to EC needs to be handled and then queries the EC
to find out what event is pending. Then execute the following ACPI
_QDF method which defined in ACPI DSDT for EC to notify power button.
Method (_QDF, 0, NotSerialized) // _Qxx: EC Query
{
Notify (PWRB, 0x80) // Status Change
}
With more debug messages added to analyze this problem, we find that
the keypress does wake up the system from suspend-to-idle but it's back
to suspend again almost immediately. As we see in the following messages,
the acpi_button_notify() is invoked but acpi_pm_wakeup_event() can not
really wake up the system here because acpi_s2idle_wakeup() is false.
The acpi_s2idle_wakeup() returnd false because the acpi_s2idle_sync() has
alrealdy exited.
[ 52.987048] s2idle_loop going s2idle
[ 59.713392] acpi_s2idle_wake enter
[ 59.713394] acpi_s2idle_wake exit
[ 59.760888] acpi_ev_gpe_detect enter
[ 59.760893] acpi_s2idle_sync enter
[ 59.760893] acpi_ec_query_flushed ec pending queries 0
[ 59.760953] Read registers for GPE 50-57: Status=01, Enable=01, RunEnable=01, WakeEnable=00
[ 59.760955] ACPI: EC: ===== IRQ (1) =====
[ 59.760972] ACPI: EC: EC_SC(R) = 0x28 SCI_EVT=1 BURST=0 CMD=1 IBF=0 OBF=0
[ 59.760979] ACPI: EC: +++++ Polling enabled +++++
[ 59.760979] ACPI: EC: ##### Command(QR_EC) submitted/blocked #####
[ 59.761003] acpi_s2idle_sync exit
[ 59.769587] ACPI: EC: ##### Query(0xdf) started #####
[ 59.769611] ACPI: EC: ##### Query(0xdf) stopped #####
[ 59.774154] acpi_button_notify button type 1
[ 59.813175] s2idle_loop going s2idle
acpi_s2idle_sync() already makes an effort to flush the EC event
queue, but in this case, the EC event has yet to be generated when
the call to acpi_ec_flush_work() is made. The event is generated
shortly after, through the ongoing handling of the SCI interrupt
which is happening on another CPU, and we must synchronize that
to make sure that it has run and completed. Adding another call to
acpi_os_wait_events_complete() solves this issue, since that
function synchronizes with SCI interrupt completion.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some PCIe features (AER, DPC, hotplug, PME) can be managed by either the
platform firmware or the OS, so the host bridge driver may have to request
permission from the platform before using them. On ACPI systems, this is
done by negotiate_os_control() in acpi_pci_root_add().
The PCIe port driver later uses pcie_port_platform_notify() and
pcie_port_acpi_setup() to figure out whether it can use these features.
But all we need is a single bit for each service, so these interfaces are
needlessly complicated.
Simplify this by adding bits in the struct pci_host_bridge to show when the
OS has permission to use each feature:
+ unsigned int native_aer:1; /* OS may use PCIe AER */
+ unsigned int native_hotplug:1; /* OS may use PCIe hotplug */
+ unsigned int native_pme:1; /* OS may use PCIe PME */
These are set when we create a host bridge, and the host bridge driver can
clear the bits corresponding to any feature the platform doesn't want us to
use.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix once per second (round_robin_time) memory leak of about 1 KB in
each acpi_pad kernel idling thread that is activated.
Found by testing with kmemleak.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some BIOSen do not handle 0-byte transfer lengths for the _LSR and _LSW
(label storage read/write) methods. This causes Linux to fallback to the
deprecated _DSM path, or otherwise disable label support.
Introduce acpi_nvdimm_has_method() to detect whether a method is
available rather than calling the method, require _LSI and _LSR to be
paired, and require read support before enabling write support.
Cc: <stable@vger.kernel.org>
Fixes: 4b27db7e26 ("acpi, nfit: add support for the _LS...")
Suggested-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some functions definitions have either the initial open brace and/or
the closing brace outside of column 1.
Move those braces to column 1.
This allows various function analyzers like gnu complexity to work
properly for these modified functions.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull libnvdimm fixes from Dan Williams:
"Two regression fixes, two bug fixes for older issues, two fixes for
new functionality added this cycle that have userspace ABI concerns,
and a small cleanup. These have appeared in a linux-next release and
have a build success report from the 0day robot.
* The 4.16 rework of altmap handling led to some configurations
leaking page table allocations due to freeing from the altmap
reservation rather than the page allocator.
The impact without the fix is leaked memory and a WARN() message
when tearing down libnvdimm namespaces. The rework also missed a
place where error handling code needed to be removed that can lead
to a crash if devm_memremap_pages() fails.
* acpi_map_pxm_to_node() had a latent bug whereby it could
misidentify the closest online node to a given proximity domain.
* Block integrity handling was reworked several kernels back to allow
calling add_disk() after setting up the integrity profile.
The nd_btt and nd_blk drivers are just now catching up to fix
automatic partition detection at driver load time.
* The new peristence_domain attribute, a platform indicator of
whether cpu caches are powerfail protected for example, is meant to
be a single value enum and not a set of flags.
This oversight was caught while reviewing new userspace code in
libndctl to communicate the attribute.
Fix this new enabling up so that we are not stuck with an unwanted
userspace ABI"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, nfit: fix persistence domain reporting
libnvdimm, region: hide persistence_domain when unknown
acpi, numa: fix pxm to online numa node associations
x86, memremap: fix altmap accounting at free
libnvdimm: remove redundant assignment to pointer 'dev'
libnvdimm, {btt, blk}: do integrity setup before add_disk()
kernel/memremap: Remove stale devres_free() call
Per the ACPI specification the only functional purpose for a DIMM
Control Region to be mapped into the system physical address space, from
an OSPM perspective, is to support block-apertures. However, there are
some BIOSen that publish DIMM Control Region SPA entries for pre-boot
environment consumption. Undo the kernel policy of generating disabled
'ndblk' regions when this configuration is detected.
Cc: <stable@vger.kernel.org>
Fixes: 1f7df6f88b ("libnvdimm, nfit: regions (block-data-window...)")
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The persistence domain is a point in the platform where once writes
reach that destination the platform claims it will make them persistent
relative to power loss. In the ACPI NFIT this is currently communicated
as 2 bits in the "NFIT - Platform Capabilities Structure". The bits
comprise a hierarchy, i.e. bit0 "CPU Cache Flush to NVDIMM Durability on
Power Loss Capable" implies bit1 "Memory Controller Flush to NVDIMM
Durability on Power Loss Capable".
Commit 96c3a23905 "libnvdimm: expose platform persistence attr..."
shows the persistence domain as flags, but it's really an enumerated
hierarchy.
Fix this newly introduced user ABI to show the closest available
persistence domain before userspace develops dependencies on seeing, or
needing to develop code to tolerate, the raw NFIT flags communicated
through the libnvdimm-generic region attribute.
Fixes: 96c3a23905 ("libnvdimm: expose platform persistence attr...")
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
All uploaded PM data from non-dom0 CPUs takes the info from vCPU 0 and
changing only the acpi_id. For processors which P-state coordination type
is HW_ALL (0xFD) it is OK to upload bogus P-state dependency information
(_PSD), because Xen will ignore any cpufreq domains created for past CPUs.
Albeit for platforms which expose coordination types as SW_ANY or SW_ALL,
this will have some unintended side effects. Effectively, it will look at
the P-state domain existence and *if it already exists* it will skip the
acpi-cpufreq initialization and thus inherit the policy from the first CPU
in the cpufreq domain. This will finally lead to the original cpu not
changing target freq to P0 other than the first in the domain. Which will
make turbo boost not getting enabled (e.g. for 'performance' governor) for
all cpus.
This patch fixes that, by also evaluating _PSD when we enumerate all ACPI
processors and thus always uploading the correct info to Xen. We export
acpi_processor_get_psd() for that this purpose, but change signature
to not assume an existent of acpi_processor given that ACPI isn't creating
an acpi_processor for non-dom0 CPUs.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Just like many other Samsung models, the 670Z5E needs to use the acpi-video
backlight interface rather then the native one for backlight control to
work, add a quirk for this.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1557060
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce a driver for the ACPI Time and Alarm Device (TAD) based on
Section 9.18 of ACPI 6.2.
This driver only supports the system wakeup capabilities of the TAD
which are mandatory. Support for the RTC capabilities of the TAD
will be added to it in the future.
This driver is entirely sysfs-based. It provides attributes (under
the TAD platform device) to allow user space to manage the AC and DC
wakeup timers of the TAD: set and read their values, set and check
their expire timer wake policies, check and clear their status and
check the capabilities of the TAD reported by AML. The DC timer
attributes are only present if the TAD supports a separate DC alarm
timer.
The wakeup events handling and power management of the TAD is
expected to be taken care of by the ACPI PM domain attached to its
platform device.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In current design of ACPI container offline, Kernel emits
KOBJ_CHANGE uevent to user space to indidate that the ejection of
the container was triggered by platform. (caa73ea15 patch)
A pure KOBJ_CHANGE uevent is not enough for user space to identify
the purpose. For example, a "udevadm trigger" command can also
be used to emit change event to all udev rules. A udev rule can not
identify that the event is from kernel for offline or from udevadm
for other purpose. Then the offline action in udev rule may also be
triggered by udevadm tool.
So, similar to the change uevent of dock, kernel sends the
KOBJ_CHANGE uevent with a offline environmental data to indicate
purpose. It's useful by udev rule for using ENV{EVENT} filter.
Acked-by: Michal Hocko <mhocko@suse.com>
Tested-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: "Lee, Chun-Yi" <jlee@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_dev_pm_get_state() is used to determine the range of allowable
device power states when going into S3 suspend. This is implemented
by executing the _S3D and _S3W ACPI methods.
Linux follows the ACPI spec behaviour in that when _S3D is implemented
and _S3W is not, Linux will not go into a power state deeper than the one
returned by _S3D for a wakeup-enabled device.
However, this same logic is being applied to the case when neither
_S3D nor _S3W are present, and the result is that this function
decides that the device must stay in D0 (fully on) state.
This is breaking USB wakeups on Asus V222GA and Acer XC-830. _S3D and
_S3W are not present, so the USB controller is left in the D0 running
state during S3, and hence it is unable to generate a PME# wake event.
The ACPI spec is unclear on which power states are permissable for
wakeup-enabled devices when both _S3D and _S3W are missing.
However, USB wakeups work fine on these platforms under Windows, where
device manager shows that they are using D3 device state for the USB
controller in S3.
I assume that the "max = min" clamping done by the code here is
specifically written for the _S3D but no _S3W case. By making the
code true to those conditions, avoiding them on these platforms,
the controller will be put into D3 state and USB wakeups start working.
Additionally I feel that this change makes the code more directly
mirror the wording of the ACPI spec and it's associated lack of clarity.
Thanks to Mathias Nyman for pointing us in the right direction.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Link: http://lkml.kernel.org/r/CAB4CAwf_k-WsF3zL4epm9TKAOu0h=Bv1XhXV_gY3bziOo_NPKA@mail.gmail.comhttps://phabricator.endlessm.com/T21410
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The resource allocation in WDAT watchdog has off-one-by error, it sets
one byte more than the actual end address. This may eventually lead
to unexpected resource conflicts.
Fixes: 058dfc7670 (ACPI / watchdog: Add support for WDAT hardware watchdog)
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Revert commit c68f0676ef ("ACPI / battery: Add quirk for Asus
GL502VSK and UX305LA") and commit 4446823e25 ("ACPI / battery: Add
quirk for Asus UX360UA and UX410UAK").
On many many Asus products, the battery is sometimes reported as
charging or discharging even when it is full and you are on AC power.
This change quirked the kernel to avoid advertising the discharging
state when this happens on 4 laptop models, under the belief that
this was incorrect information. I presume it originates from user
reports who are confused that their battery status icon says that it
is discharging.
However, the reported information is indeed correct, and the quirk
approach taken is inadequate and more thought is needed first.
Specifically:
1. It only quirks discharging state, not charging
2. There are so many different Asus products and DMI naming variants
within those product families that behave this way; Linux could
grow to quirk hundreds of products and still not even be close at
"winning" this battle.
3. Asus previously clarified that this behaviour is intentional. The
platform will periodically do a partial discharge/charge cycle
when the battery is full, because this is one way to extend the
lifetime of the battery (leaving a battery at 100% charge and
unused will decrease its usable capacity over time).
My understanding is that any decent consumer product will have
this behaviour, but it appears that Asus is different in that
they expose this info through ACPI.
However, the behaviour seems correct. The ACPI spec does not
suggest in that the platform should hide the truth. It lets you
report that the battery is full of charge, and discharging, and
with external power connected; and Asus does this.
4. In terms of not confusing the user, this seems like something that
could/should be handled by userspace, which can also detect these
same (accurate) conditions in the general case.
Revert this quirk before it gets included in a release, while we look
for better approaches.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a device referred to by ACPI LPI constrains (coming from function 1
of the Low Power S0 Idle _DSM interface) is not power-manageable via
ACPI (no _PS0 method and no power resources), the code generating
diagnostic information for the LPI constraints will print a message
about that to the kernel log on every system suspend-resume cycle
(possibly for multiple times).
That is not very useful and noisy, so modify that code to disregard
the LPI list entries corresponding to the devices that are not power-
manageable after printing that information for them once.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Fix grammar and punctuation (end sentences with a period) in the
Kconfig help text for ACPI_PROCFS_POWER.
I was looking at this since it appears to be going away (again,
some day) and I have a working script that uses this info to tell me
battery usage. I can update the script to use /sys/class/power_supply
(in theory) but the contents (with units) should be documented in
Documentation/ABI/ before /proc/acpi/battery/ is removed (IMO).
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A number of Dell systems require an OEM _OSI string "Linux-Dell-Video"
as a BIOS workaround to disable RTD3 which causes systems hangs when
NVidia graphics cards are installed. The affected Dell systems are
with system IDs: 0818, 0819, 0820, 0850, 0851, 086F, 0870, 0885 and
0886.
The form of the OEM _OSI strings is defined by each OEMs and is
discussed in Documentation/acpi/osi.txt.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This prepares the code for eventual removal of the original
style of deferred execution of the MLC.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This ensures that acpi_ev_fixed_event_detect() does not use fixed_status
and and fixed_enable as uninitialized variables.
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Was acpi_gbl_parse_table_as_term_list, changed to:
acpi_gbl_execute_tables_as_methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixing the ACPI_ERROR_NAMESPACE macros created an "unused variable"
compile error when ACPI_NO_ERROR_MESSAGES was defined. This commit
also fixes the above compilation errors by surrounding variables
meant for debugging inside a new ACPI_ERROR_ONLY macro.
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Changes the option to ignore package resolution errors into
a runtime option.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As the documentatuon above its declaration indicates, acpi_get_object_info()
is intended for early probe usage and as such should not call any methods
which may rely on op_regions, before this commit it was also calling _STA,
which on some systems does rely on op_regions.
Calling _STA before things are ready leads to errors such as these
(under Linux, on some hardware):
[ 0.123579] ACPI Error: No handler for Region [ECRM] (00000000ba9edc4c)
[generic_serial_bus] (20170831/evregion-166)
[ 0.123601] ACPI Error: Region generic_serial_bus (ID=9) has no handler
(20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (20170831/psparse-550)
End 2015 support for the _SUB method was removed for exactly the same
reason. Removing current_status from struct acpi_device_info only has a limited
impact. Within ACPICA it is only used by 2 debug messages, both
of which are modified to no longer print it with this commit.
Outside of ACPICA, there was one user in Linux, which has been patched to
no longer use current_status in Torvald's current master.
I've not checked if free_BSD or others are using the current_status field.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The implementation previously ignored null strings (""), but
these could be important, especially for debug.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes a single-object memory leak on a store-to-reference method
invocation. ACPICA BZ 1439.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After being enabled for the first time, the GPEs may have STS bits already
set. Setting EN bits is not sufficient to trigger the GPEs again, so this
patch polls GPEs after enabling them for the first time.
This is a cleaner version on top of the "GPE clear" fix generated according
to Mika's report and Rafael's original Linux based fix. Based on Linux
commit originated from Rafael J. Wysocki, fixed by Lv Zheng.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is a risk that a GPE method/handler may be invoked twice. Let's
consider a case, both GPE0(RAW_HANDLER) and GPE1(_Exx) is triggered.
=======================================+=============================
IRQ handler (top-half) |IRQ polling
=======================================+=============================
acpi_ev_detect_gpe() |
LOCK() |
READ (GPE0-7 enable/status registers)|
^^^^^^^^^^^^ROOT CAUSE^^^^^^^^^^^^^^^|
Walk GPE0 |
UNLOCK() |LOCK()
Invoke GPE0 RAW_HANDLER |READ (GPE1 enable/status bit)
|acpi_ev_gpe_dispatch(irq=false)
| CLEAR (GPE1 enable bit)
| CLEAR (GPE1 status bit)
LOCK() |UNLOCK()
Walk GPE1 +=============================
acpi_ev_gpe_dispatch(irq=true) |IRQ polling (defer)
CLEAR (GPE1 enable bit) +=============================
CLEAR (GPE1 status bit) |acpi_ev_async_execute_gpe_method()
Walk others | Evaluate GPE1 _Exx
fi | acpi_ev_async_enable_gpe()
UNLOCK() | LOCK()
=======================================+ SET (GPE enable bit)
IRQ handler (bottom-half) | UNLOCK()
=======================================+
acpi_ev_async_execute_gpe_method() |
Evaluate GPE1 _Exx |
acpi_ev_async_enable_gpe() |
LOCK() |
SET (GPE1 enable bit) |
UNLOCK() |
=======================================+=============================
If acpi_ev_detect_gpe() is only invoked from the IRQ context, there won't be
more than one _Lxx/_Exx evaluations for one status bit flagging if the IRQ
handlers controlled by the underlying IRQ chip/driver (ex. APIC) are run in
serial. Note that, this is a known potential gap and we had an approach,
locking entire non-raw-handler processes in the top-half IRQ handler and
handling all raw-handlers out of the locked loop to be friendly to those
IRQ chip/driver. But the approach is too complicated while the issue is not
so real, thus ACPICA treated such issue (if any) as a parallelism/quality
issue of the underlying IRQ chip/driver to stop putting it on the radar.
Bug in link #1 is suspiciously reflecting the same cause, and if so, it can
also be fixed by this simpler approach.
But it will be no excuse an ACPICA problem now if ACPICA starts to poll
IRQs itself. In the changed scenario, _Exx will be evaluated from the task
context due to new ACPICA provided "polling after enabling GPEs" mechanism.
And the above figure uses edge-triggered GPEs demonstrating the possibility
of evaluating _Exx twice for one status bit flagging.
As a conclusion, there is now an increased chance of evaluating _Lxx/_Exx
more than once for one status bit flagging.
However this is still not a real problem if the _Lxx/_Exx checks the
underlying hardware IRQ reasoning and finally just changes the 2nd and the
follow-up evaluations into no-ops. Note that _Lxx should always be written
in this way as a level-trigger GPE could have it's status wrongly
duplicated by the underlying IRQ delivery mechanisms. But _Exx may have
very low quality BIOS by BIOS to trigger real issues. For example, trigger
duplicated button notifications.
To solve this issue, we need to stop reading a bunch of enable/status
register bits, but read only one GPE's enable/status bit. And GPE status
register's W1C nature ensures that acknowledging one GPE won't affect
another GPEs' status bits. Thus the hardware GPE architecture has already
provided us with the mechanism of implementing such parallelism.
So we can lock around one GPE handling process to achieve the parallelism:
1. If we can incorporate GPE enable bit check in detection and ensure the
atomicity of the following process (top-half IRQ handler):
READ (enable/status bit)
if (enabled && raised)
CLEAR (enable bit)
and handle the GPE after this process, we can ensure that we will only
invoke GPE handler once for one status bit flagging.
2. In addtion for edge-triggered GPEs, if we can ensure the atomicity of
the following process (top-half IRQ handler):
READ (enable/status bit)
if (enabled && raised)
CLEAR (enable bit)
CLEAR (status bit)
and handle the GPE after this process, we can ensure that we will only
invoke GPE handler once for one status bit flagging.
By doing a cleanup in this way, we can remove duplicate GPE handling code
and ensure that all logics are collected in 1 function. And the function
will be safe for both IRQ interrupt and IRQ polling, and will be safe for
us to release and re-acquire acpi_gbl_gpe_lock at any time rather than raw
handler only during the top-half IRQ handler. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196703 [#1]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Unconditionally clearing ACPI IRQs during suspend/resume can lead to
unexpected IRQ losts. This patch fixes this issue by removing such IRQ
clearing code.
If this patch triggers regression, the regression should be in the GPE
handlers that cannot correctly determine some spurious triggered events as
no-ops. Please report any regression related to this commit to the ACPI
component on kernel bugzilla. Lv Zheng.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196249
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Eric Bakula-Davis <ericbakuladavis@gmail.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 99759869fa "acpi: Add acpi_map_pxm_to_online_node()" added
support for mapping a given proximity to its nearest, by SLIT distance,
online node. However, it sometimes returns unexpected results due to the
fact that it switches from comparing the PXM node to the last node that
was closer than the current max.
for_each_online_node(n) {
dist = node_distance(node, n);
if (dist < min_dist) {
min_dist = dist;
node = n; <---- from this point we're using the
wrong node for node_distance()
Fixes: 99759869fa ("acpi: Add acpi_map_pxm_to_online_node()")
Cc: <stable@vger.kernel.org>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
EDAC driver needs to look up attributes of NVDIMMs provided in SMBIOS.
Provide a function that looks up an acpi_nfit_memory_map from a device
handle (node/socket/mc/channel/dimm) and returns the SMBIOS handle.
Also pass back the "flags" so we can see if the NVDIMM is OK.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Erik Schmauss <erik.schmauss@intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Robert Moore <robert.moore@intel.com>
Cc: devel@acpica.org
Cc: linux-acpi@vger.kernel.org
Cc: linux-nvdimm@lists.01.org
Link: http://lkml.kernel.org/r/20180312182430.10335-4-tony.luck@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Revert commit 91eea70e5e (ACPI: battery: Add the ThinkPad "Not
Charging" quirk) as it is reported to cause user space to misbehave.
That appears to be due to bugs in user space, so this commit will go
in again after the bugs have been fixed and the fixes have been
delivered to users.
Link: https://marc.info/?l=linux-acpi&m=152089585129589&w=2
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To defeat ACPICA<->kernel merge order dependencies a preprocessor define
value was introduced in the IORT compilation unit according to IORT
revision C, IORT_SMMU_V3_CAVIUM_CN99XX, so that even if the value was
not defined in ACPICA headers the IORT kernel layer would still be able
to function and use it.
Since commit 0c2021c047 ("ACPICA: IORT: Update SMMU models for
revision C") finally added the define in ACPICA headers, as required by
ACPICA IORT support, the preprocessor definition in the IORT kernel
compilation unit has become obsolete and can be removed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
In IORT issue C SMMUv3 IORT nodes gained an additional field (DeviceID
mapping index) so that the SMMUv3 can describe its MSI interrupts.
Referring to it in the kernel requires ACPICA changes and in order
to prevent kernel<->ACPICA dependencies kernel code depending on the
SMMUv3 DeviceID mapping index field was guarded with an ACPICA version
conditional.
ACPICA changes introducing DeviceID mapping index in the IORT structs
were integrated in the kernel with:
commit 4c106aa411 ("ACPICA: iasl: Add SMMUv3 device ID mapping index
support")
so the temporary ACPICA guard has become stale and can be removed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Dynamic debug can be instructed to add the function name to the debug
output using the +f switch, so there is no need for the nfit module to
do it again. If a user decides to add the +f switch for nfit's dynamic
debug this results in double prints of the function name like the
following:
[ 2391.935383] acpi_nfit_ctl: nfit ACPI0012:00: acpi_nfit_ctl:nmem8 cmd: 10: func: 1 input length: 0
Thus remove the stray __func__ printing.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
With a degraded battery, full_charge_capacity can be less
than design_capacity, however it's not sure that capacity_now's
max will follow.
Example from an affected machine:
/sys/class/power_supply/BAT0/charge_full -> 4290000
/sys/class/power_supply/BAT0/charge_full_design -> 5900000
/sys/class/power_supply/BAT0/charge_now -> 5900000
/sys/class/power_supply/BAT0/capacity -> 137
The battery is a degraded one with a full charge, and
charge_now is the value of charge_full_design instead of
charge_full.
Added a new quirk to test and correct this, and
a new function to check if the battery is a degraded one
or not. This keeps the possibility to be over 100 if
it's really the case.
Signed-off-by: Laszlo Toth <laszlth@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In recent Intel hardware the IRQs become non-configurable after BIOS
initializes them in PEI phase and _PRS objects are no longer included in
ASL.
This is the same as "static (non-configurable) devices do not
specify a _PRS object" in ACPI spec. As a result, error messages
saying "ACPI Exception: AE_NOT_FOUND, Evaluating _PRS" does not need to
be in kernel messenges all the time but only when debug is enabled, and
acpi_pci_link_get_possible should not return -ENODEV when _PRS is
absent.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function __battery_hook_unregister is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/acpi/battery.c:654:6: warning: symbol '__battery_hook_unregister'
was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add an architecture specific function to get the address of the RSDP
table. Per default it will just return 0 indicating falling back to
the current mechanism.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: boris.ostrovsky@oracle.com
Cc: lenb@kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20180219100906.14265-2-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
...instead of open coding its functionality.
No changes in functionality.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-acpi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Link: http://lkml.kernel.org/r/20180222125923.57385-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove the GPL v2 license boilerplate and update with
the SPDX license identifier.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CPPC dirver is aware of multiple PCC subspace IDs. Enhance the debug
and error messages in the driver to print the subspace id. In case of
error it will be helpful to find which particular subspace is failing.
Signed-off-by: George Cherian <george.cherian@cavium.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These tables, NFIT and HMAT, are essential for describing
next-generation platform memory topologies and performance
characteristics. Allow them to be overridden for debug and test and
purposes.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is reported that commit 235d81a630 (ACPI / PM: Clean up device
wakeup enable/disable code) broke wakeup from suspend-to-idle on
some platforms. That is due to the acpi_enable_all_wakeup_gpes() in
acpi_s2idle_prepare() which needs acpi_enable_wakeup_devices() to be
called before it as the latter sets up the GPE masks used by the
former and commit 235d81a630 removed acpi_enable_wakeup_devices()
invocation from the suspend-to-idle path.
However, acpi_enable_wakeup_devices() does more than just setting
the GPE masks and the remaining part of it is not necessary for
suspend-to-idle. Moreover, non-wakeup GPEs are disabled on suspend-
to-idle entry to avoid spurious wakeups, but that should not be
strictly necessary any more after commit 33e4f80ee6 (ACPI / PM:
Ignore spurious SCI wakeups from suspend-to-idle) which prevents
spurious GPE wakeups from resuming the system. The only consequence
of leaving non-wakeup GPEs enabled may be more interrupt-related
activity while suspended, which is not ideal (more energy is used
if that happens), but it is not critical too.
For this reason, drop the GPE reconfiguration from the suspend-to-idle
path entirely.
This change also allows Dells XPS13 9360 blacklisted by commit
71630b7a83 (ACPI / PM: Blacklist Low Power S0 Idle _DSM for Dell
XPS13 9360) to use the power button for waking up from suspend-
to-idle and it helps at least one other older Dell system (the
wakeup button GPE on that one is not listed in _PRW for any
devices, so it is not regarded as a wakeup one and gets disabled
on suspend-to-idle entry today).
Fixes: 235d81a630 (ACPI / PM: Clean up device wakeup enable/disable code)
Reported-by: Du Wenkai <wenkai.du@intel.com>
Tested-by: Du Wenkai <wenkai.du@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit a6c3c725c44dd44ad9d3f2b2a64351fdbe6e0014
For the kernel-resident ACPICA, optionally be silent about the
NOT_FOUND case. Although this is potentially a serious problem,
it can generate a lot of noise/errors on platforms whose
firmware carries around a bunch of unused Package objects.
To disable these errors, define ACPI_IGNORE_PACKAGE_RESOLUTION_ERRORS
in the OS-specific header.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198167
Link: https://github.com/acpica/acpica/commit/a6c3c725
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 8faf6fca445eb7219963d80543fb802302a7a8c7
This change completes the integration of the recent changes to
package object handling with the module-level code support.
For acpi_exec, the -ep flag is removed.
This change allows table load to behave as if it were a method
invocation. Before this, the definition block definition below would
have loaded all named objects at the root scope. After loading, it
would execute the if statements at the root scope.
DefinitionBlock (...)
{
Name(OBJ1, 0)
if (1)
{
Device (DEV1)
{
Name (_HID,0x0)
}
}
Scope (DEV1)
{
Name (OBJ2)
}
}
The above code would load OBJ1 to the namespace, defer the execution
of the if statement and attempt to add OBJ2 within the scope of DEV1.
Since DEV1 is not in scope, this would incur an AE_NOT_FOUND error.
After this error is emitted, the if block is invoked and DEV1 and its
_HID is added to the namespace.
This commit changes the behavior to execute the if block in place
rather than deferring it until all tables are loaded. The new
behavior is as follows: insert OBJ1 in the namespace, invoke the if
statement and add DEV1 and its _HID to the namespace, add OBJ2 to the
scope of DEV1.
Bug report links:
Link: https://bugs.acpica.org/show_bug.cgi?id=963
Link: https://bugzilla.kernel.org/show_bug.cgi?id=153541
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196165
Link: https://bugzilla.kernel.org/show_bug.cgi?id=192621
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197207
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198051
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198515
ACPICA repo:
Link: https://github.com/acpica/acpica/commit/8faf6fca
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 0e44fee13434766ebbb4d156e3ed45604508d7c3
This reverts commit e1342c9f2dde37a67e916099658b65984ef8a434.
Implicit conversion should in fact be disabled for the "explicit
conversion" operators. This is stated in the ACPI specification.
The operators affected are:
to_integer
to_string
to_buffer
to_decimal_string
to_hex_string
to_BCD
from_BCD
Link: https://github.com/acpica/acpica/commit/0e44fee1
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 3a08436fe3bff297a6de162252964e955946c7d3
Improve/simplify some of the debug messages.
Link: https://github.com/acpica/acpica/commit/3a08436f
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 0787fda3b224a78369e26ac6046658beb2b64c12
Clarify error when an attempt is made to evaluate things like
devices, events, etc. -- these objects have no data and cannot
be "evaluated".
Link: https://github.com/acpica/acpica/commit/0787fda3
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The EC/ACPI firmware on Lenovo ThinkPads used to report a status
of "Unknown" when the battery is between the charge start and
charge stop thresholds. On Windows, it reports "Not Charging"
so the quirk has been added to also report correctly.
Now the "status" attribute returns "Not Charging" when the
battery on ThinkPads is not physicaly charging.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ognjen Galic <smclt30p@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is a patch that implements a generic hooking API for the
generic ACPI battery driver.
With this new generic API, drivers can expose platform specific
behaviour via sysfs attributes in /sys/class/power_supply/BATn/
in a generic way.
A perfect example of the need for this API are Lenovo ThinkPads.
Lenovo ThinkPads have a ACPI extension that allows the setting of
start and stop charge thresholds in the EC and battery firmware
via ACPI. The thinkpad_acpi module can use this API to expose
sysfs attributes that it controls inside the ACPI battery driver
sysfs tree, under /sys/class/power_supply/BATN/.
The file drivers/acpi/battery.h has been moved to
include/acpi/battery.h and the includes inside ac.c, sbs.c, and
battery.c have been adjusted to reflect that.
When drivers hooks into the API, the API calls add_battery() for
each battery in the system that passes it a acpi_battery
struct. Then, the drivers can use device_create_file() to create
new sysfs attributes with that struct and identify the batteries
for per-battery attributes.
Signed-off-by: Ognjen Galic <smclt30p@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On some platforms msi parent address regions have to be excluded from
normal IOVA allocation in that they are detected and decoded in a HW
specific way by system components and so they cannot be considered normal
IOVA address space.
Add a helper function that retrieves ITS address regions - the msi
parent - through IORT device <-> ITS mappings and reserves it so that
these regions will not be translated by IOMMU and will be excluded from
IOVA allocations. The function checks for the smmu model number and
only applies the msi reservation if the platform requires it.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[For the ITS part]
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Constify device_get_match_data() as OF and ACPI variants return
constant value.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Do the renaming to be consistent with its sibling, i.e.
of_device_get_match_data().
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As well as its sibling of_device_get_match_data() has no such checks,
no need to do it in acpi_get_match_data().
First of all, we are not supposed to call fwnode API like this without
driver attached.
Second, since __acpi_match_device() does check input parameter there is
no need to duplicate it outside.
And last but not least one, the API should still serve the cases when
ACPI device is enumerated via PRP0001. In such case driver has neither
ACPI table nor driver data there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When __acpi_match_device() is called it would be possible to have
ACPI ID table a NULL pointer. To avoid potential dereference,
check for this before traverse.
While here, remove redundant 'else'.
Note, this patch implies a bit of refactoring acpi_of_match_device()
to return pointer to OF ID when matched followed by refactoring
__acpi_match_device() to return either ACPI or OF ID when matches.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1465078
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 662591461c (ACPI / EC: Drop EC noirq hooks to fix a
regression) modified the ACPI EC driver so that it doesn't switch
over to busy polling mode during noirq stages of system suspend and
resume in an attempt to fix an issue resulting from that behavior.
However, that modification introduced a system resume regression on
Thinkpad X240, so make the EC driver switch over to the polling mode
during noirq stages of system suspend and resume again, which
effectively reverts the problematic commit.
Fixes: 662591461c (ACPI / EC: Drop EC noirq hooks to fix a regression)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197863
Reported-by: Markus Demleitner <m@tfiu.de>
Tested-by: Markus Demleitner <m@tfiu.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Update the ACPICA kernel code to upstream revision 20180105 including:
* Assorted fixes (Jung-uk Kim).
* Support for X32 ABI compilation (Anuj Mittal).
* Update of ACPICA copyrights to 2018 (Bob Moore).
- Prepare for future modifications to avoid executing the _STA control
method too early (Hans de Goede).
- Make the processor performance control library code ignore _PPC
notifications if they cannot be handled and fix up the C1 idle
state definition when it is used as a fallback state (Chen Yu,
Yazen Ghannam).
- Make it possible to use the SPCR table on x86 and to replace the
original IORT table with a new one from initrd (Prarit Bhargava,
Shunyong Yang).
- Add battery-related quirks for Asus UX360UA and UX410UAK and add
quirks for table parsing on Dell XPS 9570 and Precision M5530
(Kai Heng Feng).
- Address static checker warnings in the CPPC code (Gustavo Silva).
- Avoid printing a raw pointer to the kernel log in the smart
battery driver (Greg Kroah-Hartman).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=rVdp
-----END PGP SIGNATURE-----
Merge tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups, a few new quirks, a couple of
updates related to the handling of ACPI tables and ACPICA copyrights
refreshment.
Specifics:
- Update the ACPICA kernel code to upstream revision 20180105
including:
* Assorted fixes (Jung-uk Kim)
* Support for X32 ABI compilation (Anuj Mittal)
* Update of ACPICA copyrights to 2018 (Bob Moore)
- Prepare for future modifications to avoid executing the _STA
control method too early (Hans de Goede)
- Make the processor performance control library code ignore _PPC
notifications if they cannot be handled and fix up the C1 idle
state definition when it is used as a fallback state (Chen Yu,
Yazen Ghannam)
- Make it possible to use the SPCR table on x86 and to replace the
original IORT table with a new one from initrd (Prarit Bhargava,
Shunyong Yang)
- Add battery-related quirks for Asus UX360UA and UX410UAK and add
quirks for table parsing on Dell XPS 9570 and Precision M5530 (Kai
Heng Feng)
- Address static checker warnings in the CPPC code (Gustavo Silva)
- Avoid printing a raw pointer to the kernel log in the smart battery
driver (Greg Kroah-Hartman)"
* tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: sbshc: remove raw pointer from printk() message
ACPI: SPCR: Make SPCR available to x86
ACPI / CPPC: Use 64-bit arithmetic instead of 32-bit
ACPI / tables: Add IORT to injectable table list
ACPI / bus: Parse tables as term_list for Dell XPS 9570 and Precision M5530
ACPICA: Update version to 20180105
ACPICA: All acpica: Update copyrights to 2018
ACPI / processor: Set default C1 idle state description
ACPI / battery: Add quirk for Asus UX360UA and UX410UAK
ACPI: processor_perflib: Do not send _PPC change notification if not ready
ACPI / scan: Use acpi_bus_get_status() to initialize ACPI_TYPE_DEVICE devs
ACPI / bus: Do not call _STA on battery devices with unmet dependencies
PCI: acpiphp_ibm: prepare for acpi_get_object_info() no longer returning status
ACPI: export acpi_bus_get_status_handle()
ACPICA: Add a missing pair of parentheses
ACPICA: Prefer ACPI_TO_POINTER() over ACPI_ADD_PTR()
ACPICA: Avoid NULL pointer arithmetic
ACPICA: Linux: add support for X32 ABI compilation
ACPI / video: Use true for boolean value
* acpi-video:
ACPI / video: Use true for boolean value
* acpi-battery:
ACPI / battery: Add quirk for Asus UX360UA and UX410UAK
* acpi-cppc:
ACPI / CPPC: Use 64-bit arithmetic instead of 32-bit
* acpi-tables:
ACPI: SPCR: Make SPCR available to x86
ACPI / tables: Add IORT to injectable table list
* acpi-bus:
ACPI / bus: Parse tables as term_list for Dell XPS 9570 and Precision M5530
ACPI / scan: Use acpi_bus_get_status() to initialize ACPI_TYPE_DEVICE devs
ACPI / bus: Do not call _STA on battery devices with unmet dependencies
PCI: acpiphp_ibm: prepare for acpi_get_object_info() no longer returning status
ACPI: export acpi_bus_get_status_handle()
* acpi-processor:
ACPI / processor: Set default C1 idle state description
ACPI: processor_perflib: Do not send _PPC change notification if not ready
* acpica:
ACPICA: Update version to 20180105
ACPICA: All acpica: Update copyrights to 2018
ACPICA: Add a missing pair of parentheses
ACPICA: Prefer ACPI_TO_POINTER() over ACPI_ADD_PTR()
ACPICA: Avoid NULL pointer arithmetic
ACPICA: Linux: add support for X32 ABI compilation
There's no need to be printing a raw kernel pointer to the kernel log at
every boot. So just remove it, and change the whole message to use the
correct dev_info() call at the same time.
Reported-by: Wang Qize <wang_qize@venustech.com.cn>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SPCR is currently only enabled or ARM64 and x86 can use SPCR to setup
an early console.
General fixes include updating Documentation & Kconfig (for x86),
updating comments, and changing parse_spcr() to acpi_parse_spcr(),
and earlycon_init_is_deferred to earlycon_acpi_spcr_enable to be
more descriptive.
On x86, many systems have a valid SPCR table but the table version is
not 2 so the table version check must be a warning.
On ARM64 when the kernel parameter earlycon is used both the early console
and console are enabled. On x86, only the earlycon should be enabled by
by default. Modify acpi_parse_spcr() to allow options for initializing
the early console and console separately.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Mark Salter <msalter@redhat.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add suffix ULL to constant 500 in order to give the compiler complete
information about the proper arithmetic to use. Notice that this
constant is used in a context that expects an expression of type
u64 (64 bits, unsigned).
The expression NUM_RETRIES * cppc_ss->latency at line 578, which at
preprocessing time translates to 500 * cppc_ss->latency is currently
being evaluated using 32-bit arithmetic.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Loading IORT table from initrd can be used to fix severe firmware
IORT defects temporarily before platform/BIOS vendor releases an
upgraded BIOS binary.
Moreover, it is very powerful to debug SMMU node/device probe, MSI
allocation, stream id translation and IORT table from firmware.
It is also very useful to enable SMMU and devices behind SMMU before
firmware is ready.
This patch adds ACPI_SIG_IORT to the table, which enables IORT
from initrd to override which from firmware.
Signed-off-by: Yang Shunyong <shunyong.yang@hxt-semitech.com>
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
New model support added for Dell, Ideapad, Acer, Asus, Thinkpad, and GPD
laptops. Improvements to the common intel-vbtn driver, including tablet
mode, rotate, and front button support. Intel CPU support added for
Cannonlake and platform support for Dollar Cove power button.
Overhaul of the mellanox platform driver, creating a new
platform/mellanox directory for the newly multi-architecture regmap
interface.
Significant Intel PMC update with CannonLake support, Coffeelake update,
CPUID enumeration, module support, new read64 API, refactoring and
cleanups.
Revert the apple-gmux iGP IO lock, addressing reported issues with
non-binary drivers, leaving Nvidia binary driver users to comment out
conflicting code.
Miscellaneous fixes and cleanups.
Previously merged during the 4.15-rc cycle:
- e20a8e771d platform/x86: dell-laptop: Fix keyboard max lighting for Dell Latitude E6410
- 9cd5cf3710 platform/x86: asus-wireless: send an EV_SYN/SYN_REPORT between state changes
- 91c73e8092 platform/x86: dell-wmi: check for kmalloc() errors
- 9a1a625918 platform/x86: wmi: Call acpi_wmi_init() later
The following is an automated git shortlog grouped by driver:
ACPI / LPIT:
- Export lpit_read_residency_count_address()
Input:
- add KEY_ROTATE_LOCK_TOGGLE
MAINTAINERS:
- Update tree for platform-drivers-x86
x86/cpu:
- Add Cannonlake to Intel family
acer-wireless:
- Add Acer Wireless Radio Control driver
intel_chtdc_ti_pwrbtn:
- Add support for Dollar Cove TI power button
GPD pocket fan:
- Add driver for GPD pocket custom fan controller
- Stop work on suspend
- Use a min-speed of 2 while charging
- Set speed to max on get_temp failure
apple-gmux:
- Revert: lock iGP IO to protect from vgaarb changes
alienware-wmi:
- lightbar LED support for Dell Inspiron 5675
asus-nb-wmi:
- Support ALS on the Zenbook UX430UQ
dell-laptop:
- Allocate buffer on heap rather than globally
- Add 2-in-1 devices to the DMI whitelist
- Filter out spurious keyboard backlight change events
- make some local functions static
- Use bool in struct quirk_entry for true/false fields
dell-smbios:
- Correct notation for filtering
dell-wmi:
- Add an event created by Dell Latitude 5495
Kconfig
- have ACPI_CMPC use depends instead of select for INPUT
ideapad-laptop:
- Add Y720-15IKB to no_hw_rfkill
- add lenovo RESCUER R720-15IKBN to no_hw_rfkill_list
- Use __func__ instead of write_ec_cmd in pr_err
- Remove unnecessary else
intel-hid:
- add a DMI quirk to support Wacom MobileStudio Pro
intel-vbtn:
- Replace License by SDPX identifier
- Remove redundant inclusions
- Support tablet mode switch
- Simplify autorelease logic
- support panel front button
- support KEY_ROTATE_LOCK_TOGGLE
- Support separate press/release events
- support SW_TABLET_MODE
intel_int0002_vgpio:
- Remove IRQF_NO_THREAD irq flag
intel_pmc_core:
- Special case for Coffeelake
- Add CannonLake PCH support
- Read base address from LPIT
- Remove unused header file
- Convert to ICPU macro
- Substitute PCI with CPUID enumeration
- Refactor debugfs entries
- Update Kconfig
- Fix file permission warnings
- Change driver to a module
- Fix kernel doc for pmc_dev
- Remove unused variable
- Remove unused EXPORTED API
intel_pmc_ipc:
- Add read64 API
intel_telemetry:
- Remove redundancies
- Improve S0ix logs
- Fix suspend stats
mlx-platform:
- Fix an ERR_PTR vs NULL issue
- Add hotplug device unregister to error path
- fix module aliases
- Add IO access verification callbacks
- Document pdev_hotplug field
- Allow compilation for 32 bit arch
platform/mellanox:
- mlxreg-hotplug: Add check for negative adapter number
- mlxreg-hotplug: Enable building for ARM
- mlxreg-hotplug: Modify to use a regmap interface
- Group create/destroy with attribute functions
- Rename i2c bus to nr
- mlxreg-hotplug: Remove unused wait.h include
- Move Mellanox platform hotplug driver to platform/mellanox
pmc_atom:
- introduce DEFINE_SHOW_ATTRIBUTE() macro
samsung-laptop:
- Grammar s/are can/can/
silead_dmi:
- Add Teclast X3 Plus tablet support
- Add entry for newer BIOS for Trekstor Surftab 7.0
- Add entry for the Teclast X98 Plus II
- Add entry for the Trekstor Primebook C13
- Add entry for the Chuwi Vi8 tablet
- add entry for Chuwi Hi8 tablet
- Add support for the Onda oBook 20 Plus tablet
- Add touchscreen info for SurfTab twin 10.1
thinkpad_acpi:
- suppress warning about palm detection
- Accept flat mode for type 4 multi mode status
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaegMmAAoJEKbMaAwKp364TvUH/3D9qNtsbXpZuc3ZMNHjIysU
hdW6hOVfBN0Rk049mjw7nWv/udhWZ/6ChJDlXHX0ZugtNGnRnzbdtWGg4y38pDF1
LRuKjWfDeyMeJ11itD2xcxEaE6YsseWCKGZJ5D3T+sN4+1jgS4RLAa9cUJMl8QAo
xZsT1MKpmGuj5eTLf5GgOVL2yfMZhZHabt3kGRY0eQqNqZBgpJw/GQNI1l6v4nAH
MHPA7Gtj4HXHK8jGviZXpD9tg/iwahiUjGugG4HcxbMcpJ96a8CGyeaXmq2FlfNC
/PpmVvhVVqzLuXKWAI+DZFLAiwIvPpxzVfOKF2Lty5Rejxf7pdmHq7aCNcALys0=
=cKm9
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.16-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform-driver updates from Darren Hart:
"New model support added for Dell, Ideapad, Acer, Asus, Thinkpad, and
GPD laptops. Improvements to the common intel-vbtn driver, including
tablet mode, rotate, and front button support. Intel CPU support added
for Cannonlake and platform support for Dollar Cove power button.
Overhaul of the mellanox platform driver, creating a new
platform/mellanox directory for the newly multi-architecture regmap
interface.
Significant Intel PMC update with CannonLake support, Coffeelake
update, CPUID enumeration, module support, new read64 API, refactoring
and cleanups.
Revert the apple-gmux iGP IO lock, addressing reported issues with
non-binary drivers, leaving Nvidia binary driver users to comment out
conflicting code.
Miscellaneous fixes and cleanups"
* tag 'platform-drivers-x86-v4.16-1' of git://git.infradead.org/linux-platform-drivers-x86: (81 commits)
platform/x86: mlx-platform: Fix an ERR_PTR vs NULL issue
platform/x86: intel_pmc_core: Special case for Coffeelake
platform/x86: intel_pmc_core: Add CannonLake PCH support
x86/cpu: Add Cannonlake to Intel family
platform/x86: intel_pmc_core: Read base address from LPIT
ACPI / LPIT: Export lpit_read_residency_count_address()
platform/x86: intel-vbtn: Replace License by SDPX identifier
platform/x86: intel-vbtn: Remove redundant inclusions
platform/x86: intel-vbtn: Support tablet mode switch
platform/x86: dell-laptop: Allocate buffer on heap rather than globally
platform/x86: intel_pmc_core: Remove unused header file
platform/x86: mlx-platform: Add hotplug device unregister to error path
platform/x86: mlx-platform: fix module aliases
platform/mellanox: mlxreg-hotplug: Add check for negative adapter number
platform/x86: mlx-platform: Add IO access verification callbacks
platform/x86: mlx-platform: Document pdev_hotplug field
platform/x86: mlx-platform: Allow compilation for 32 bit arch
platform/mellanox: mlxreg-hotplug: Enable building for ARM
platform/mellanox: mlxreg-hotplug: Modify to use a regmap interface
platform/mellanox: Group create/destroy with attribute functions
...
* Require struct page by default for filesystem DAX to remove a number of
surprising failure cases. This includes failures with direct I/O, gdb and
fork(2).
* Add support for the new Platform Capabilities Structure added to the NFIT in
ACPI 6.2a. This new table tells us whether the platform supports flushing
of CPU and memory controller caches on unexpected power loss events.
* Revamp vmem_altmap and dev_pagemap handling to clean up code and better
support future future PCI P2P uses.
* Deprecate the ND_IOCTL_SMART_THRESHOLD command whose payload has become
out-of-sync with recent versions of the NVDIMM_FAMILY_INTEL spec, and
instead rely on the generic ND_CMD_CALL approach used by the two other IOCTL
families, NVDIMM_FAMILY_{HPE,MSFT}.
* Enhance nfit_test so we can test some of the new things added in version 1.6
of the DSM specification. This includes testing firmware download and
simulating the Last Shutdown State (LSS) status.
-----BEGIN PGP SIGNATURE-----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=MIMX
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Ross Zwisler:
- Require struct page by default for filesystem DAX to remove a number
of surprising failure cases. This includes failures with direct I/O,
gdb and fork(2).
- Add support for the new Platform Capabilities Structure added to the
NFIT in ACPI 6.2a. This new table tells us whether the platform
supports flushing of CPU and memory controller caches on unexpected
power loss events.
- Revamp vmem_altmap and dev_pagemap handling to clean up code and
better support future future PCI P2P uses.
- Deprecate the ND_IOCTL_SMART_THRESHOLD command whose payload has
become out-of-sync with recent versions of the NVDIMM_FAMILY_INTEL
spec, and instead rely on the generic ND_CMD_CALL approach used by
the two other IOCTL families, NVDIMM_FAMILY_{HPE,MSFT}.
- Enhance nfit_test so we can test some of the new things added in
version 1.6 of the DSM specification. This includes testing firmware
download and simulating the Last Shutdown State (LSS) status.
* tag 'libnvdimm-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (37 commits)
libnvdimm, namespace: remove redundant initialization of 'nd_mapping'
acpi, nfit: fix register dimm error handling
libnvdimm, namespace: make min namespace size 4K
tools/testing/nvdimm: force nfit_test to depend on instrumented modules
libnvdimm/nfit_test: adding support for unit testing enable LSS status
libnvdimm/nfit_test: add firmware download emulation
nfit-test: Add platform cap support from ACPI 6.2a to test
libnvdimm: expose platform persistence attribute for nd_region
acpi: nfit: add persistent memory control flag for nd_region
acpi: nfit: Add support for detect platform CPU cache flush on power loss
device-dax: Fix trailing semicolon
libnvdimm, btt: fix uninitialized err_lock
dax: require 'struct page' by default for filesystem dax
ext2: auto disable dax instead of failing mount
ext4: auto disable dax instead of failing mount
mm, dax: introduce pfn_t_special()
mm: Fix devm_memremap_pages() collision handling
mm: Fix memory size alignment in devm_memremap_pages_release()
memremap: merge find_dev_pagemap into get_dev_pagemap
memremap: change devm_memremap_pages interface to use struct dev_pagemap
...
The i2c touchpad on Dell XPS 9570 and Precision M5530 doesn't work out
of box.
The touchpad relies on its _INI method to update its _HID value from
XXXX0000 to SYNA2393.
Also, the _STA relies on value of I2CN to report correct status.
Set acpi_gbl_parse_table_as_term_list so the value of I2CN can be
correctly set up, and _INI can get run. The ACPI table in this machine
is designed to get parsed this way.
Also, change the quirk table to a more generic name.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198515
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
including tool signons.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export lpit_read_residency_count_address(), so that it can be used from
drivers built as module. With the recent changes, the builtin_pci
functionality of the intel_pmc_core driver is removed and now it can be
built as a module to read this exported interface to calculate the PMC base
address.
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: linux-acpi@vger.kernel.org
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The ACPI idle driver will default to ACPI_CSTATE_HALT for C1 if a _CST
object for C1 is not defined. However, the description will not be set,
so users will see "<null>" when reading the description from sysfs.
Set the C1 state description when defaulting to ACPI_CSTATE_HALT.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Same issue as other Asus laptops, ACPI incorrectly reports discharging
when battery is full and AC is plugged.
Use the same battery quirk can workaround the issue.
Link: https://bugs.launchpad.net/bugs/1661876
Link: https://bugs.launchpad.net/bugs/1745032
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following warning was triggered after resumed from S3 -
if all the nonboot CPUs were put offline before suspend:
[ 1840.329515] unchecked MSR access error: RDMSR from 0x771 at rIP: 0xffffffff86061e3a (native_read_msr+0xa/0x30)
[ 1840.329516] Call Trace:
[ 1840.329521] __rdmsr_on_cpu+0x33/0x50
[ 1840.329525] generic_exec_single+0x81/0xb0
[ 1840.329527] smp_call_function_single+0xd2/0x100
[ 1840.329530] ? acpi_ds_result_pop+0xdd/0xf2
[ 1840.329532] ? acpi_ds_create_operand+0x215/0x23c
[ 1840.329534] rdmsrl_on_cpu+0x57/0x80
[ 1840.329536] ? cpumask_next+0x1b/0x20
[ 1840.329538] ? rdmsrl_on_cpu+0x57/0x80
[ 1840.329541] intel_pstate_update_perf_limits+0xf3/0x220
[ 1840.329544] ? notifier_call_chain+0x4a/0x70
[ 1840.329546] intel_pstate_set_policy+0x4e/0x150
[ 1840.329548] cpufreq_set_policy+0xcd/0x2f0
[ 1840.329550] cpufreq_update_policy+0xb2/0x130
[ 1840.329552] ? cpufreq_update_policy+0x130/0x130
[ 1840.329556] acpi_processor_ppc_has_changed+0x65/0x80
[ 1840.329558] acpi_processor_notify+0x80/0x100
[ 1840.329561] acpi_ev_notify_dispatch+0x44/0x5c
[ 1840.329563] acpi_os_execute_deferred+0x14/0x20
[ 1840.329565] process_one_work+0x193/0x3c0
[ 1840.329567] worker_thread+0x35/0x3b0
[ 1840.329569] kthread+0x125/0x140
[ 1840.329571] ? process_one_work+0x3c0/0x3c0
[ 1840.329572] ? kthread_park+0x60/0x60
[ 1840.329575] ? do_syscall_64+0x67/0x180
[ 1840.329577] ret_from_fork+0x25/0x30
[ 1840.329585] unchecked MSR access error: WRMSR to 0x774 (tried to write 0x0000000000000000) at rIP: 0xffffffff86061f78 (native_write_msr+0x8/0x30)
[ 1840.329586] Call Trace:
[ 1840.329587] __wrmsr_on_cpu+0x37/0x40
[ 1840.329589] generic_exec_single+0x81/0xb0
[ 1840.329592] smp_call_function_single+0xd2/0x100
[ 1840.329594] ? acpi_ds_create_operand+0x215/0x23c
[ 1840.329595] ? cpumask_next+0x1b/0x20
[ 1840.329597] wrmsrl_on_cpu+0x57/0x70
[ 1840.329598] ? rdmsrl_on_cpu+0x57/0x80
[ 1840.329599] ? wrmsrl_on_cpu+0x57/0x70
[ 1840.329602] intel_pstate_hwp_set+0xd3/0x150
[ 1840.329604] intel_pstate_set_policy+0x119/0x150
[ 1840.329606] cpufreq_set_policy+0xcd/0x2f0
[ 1840.329607] cpufreq_update_policy+0xb2/0x130
[ 1840.329610] ? cpufreq_update_policy+0x130/0x130
[ 1840.329613] acpi_processor_ppc_has_changed+0x65/0x80
[ 1840.329615] acpi_processor_notify+0x80/0x100
[ 1840.329617] acpi_ev_notify_dispatch+0x44/0x5c
[ 1840.329619] acpi_os_execute_deferred+0x14/0x20
[ 1840.329620] process_one_work+0x193/0x3c0
[ 1840.329622] worker_thread+0x35/0x3b0
[ 1840.329624] kthread+0x125/0x140
[ 1840.329625] ? process_one_work+0x3c0/0x3c0
[ 1840.329626] ? kthread_park+0x60/0x60
[ 1840.329628] ? do_syscall_64+0x67/0x180
[ 1840.329631] ret_from_fork+0x25/0x30
This is because if there's only one online CPU, the MSR_PM_ENABLE
(package wide)can not be enabled after resumed, due to
intel_pstate_hwp_enable() will only be invoked on AP's online
process after resumed - if there's no AP online, the HWP remains
disabled after resumed (BIOS has disabled it in S3). Then if
there comes a _PPC change notification which touches HWP register
during this stage, the warning is triggered.
Since we don't call acpi_processor_register_performance() when
HWP is enabled, the pr->performance will be NULL. When this is
NULL we don't need to do _PPC change notification.
Reported-by: Doug Smythies <dsmythies@telus.net>
Suggested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Yu Chen <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_get_bus_status wrapper for acpi_bus_get_status_handle has some
code to handle certain device quirks, in some cases we also need this
quirk handling for the initial _STA call.
Specifically on some devices calling _STA before all _DEP dependencies
are met results in errors like these:
[ 0.123579] ACPI Error: No handler for Region [ECRM] (00000000ba9edc4c)
[GenericSerialBus] (20170831/evregion-166)
[ 0.123601] ACPI Error: Region GenericSerialBus (ID=9) has no handler
(20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (20170831/psparse-550)
acpi_get_bus_status already has code to avoid this, so by using it we
also silence these errors from the initial _STA call.
Note that in order for the acpi_get_bus_status handling for this to work,
we initialize dep_unmet to 1 until acpi_device_dep_initialize gets called,
this means that battery devices will be instantiated with an initial
status of 0. This is not a problem, acpi_bus_attach will get called soon
after the instantiation anyways and it will update the status as first
point of order.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The battery code uses acpi_device->dep_unmet to check for unmet deps and
if there are unmet deps it does not bind to the device to avoid errors
about missing OpRegions when calling ACPI methods on the device.
The missing OpRegions when there are unmet deps problem also applies to
the _STA method of some battery devices and calling it too early results
in errors like these:
[ 0.123579] ACPI Error: No handler for Region [ECRM] (00000000ba9edc4c)
[GenericSerialBus] (20170831/evregion-166)
[ 0.123601] ACPI Error: Region GenericSerialBus (ID=9) has no handler
(20170831/exfldio-299)
[ 0.123618] ACPI Error: Method parse/execution failed
\_SB.I2C1.BAT1._STA, AE_NOT_EXIST (20170831/psparse-550)
This commit fixes these errors happening when acpi_get_bus_status gets
called by checking dep_unmet for battery devices and reporting a status
of 0 until all dependencies are met.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some modular drivers need this, export it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A NULL pointer reference kernel bug was observed when
acpi_nfit_add_dimm() called in acpi_nfit_register_dimms() failed. This
error path does not set nfit_mem->nvdimm, but the 2nd
list_for_each_entry() loop in the function assumes it's always set. Add
a check to nfit_mem->nvdimm.
Cc: <stable@vger.kernel.org>
Fixes: ba9c8dd3c2 ("acpi, nfit: add dimm device notification support")
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Propagate the ADR attribute flag from the NFIT platform capabilities
sub-table to nd_region.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
In ACPI 6.2a the platform capability structure has been added to the NFIT
tables. That provides software the ability to determine whether a system
supports the auto flushing of CPU caches on power loss. If the capability
is supported, we do not need to do dax_flush(). Plumbing the path to set the
property on per region from the NFIT tables.
This patch depends on the ACPI NFIT 6.2a platform capabilities support code
in include/acpi/actbl1.h.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
This cycle we have small update for:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- Add support for race free transfer termination and updating
for users for that
- Support for new rev of hidma with addition new APIs to
get device match data in ACPI/OF
- Random updates to bunch of other drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7bH/
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time is smallish update with updates mainly to drivers:
- updates to xilinx and zynqmp dma controllers
- update reside calculation for rcar controller
- more RSTify fixes for documentation
- add support for race free transfer termination and updating for
users for that
- support for new rev of hidma with addition new APIs to get device
match data in ACPI/OF
- random updates to bunch of other drivers"
* tag 'dmaengine-4.16-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (47 commits)
dmaengine: dmatest: fix container_of member in dmatest_callback
dmaengine: stm32-dmamux: Remove unnecessary platform_get_resource() error check
dmaengine: sprd: statify 'sprd_dma_prep_dma_memcpy'
dmaengine: qcom_hidma: simplify DT resource parsing
dmaengine: xilinx_dma: Free BD consistent memory
dmaengine: xilinx_dma: Fix warning variable prev set but not used
dmaengine: xilinx_dma: properly configure the SG mode bit in the driver for cdma
dmaengine: doc: format struct fields using monospace
dmaengine: doc: fix bullet list formatting
dmaengine: ti-dma-crossbar: Fix event mapping for TPCC_EVT_MUX_60_63
dmaengine: cppi41: Fix channel queues array size check
dmaengine: imx-sdma: Add MODULE_FIRMWARE
dmaengine: xilinx_dma: Fix typos
dmaengine: xilinx_dma: Differentiate probe based on the ip type
dmaengine: xilinx_dma: fix style issues from checkpatch
dmaengine: xilinx_dma: Fix kernel doc warnings
dmaengine: xilinx_dma: Fix race condition in the driver for multiple descriptor scenario
dmaeninge: xilinx_dma: Fix bug in multiple frame stores scenario in vdma
dmaengine: xilinx_dma: Check for channel idle state before submitting dma descriptor
dmaengine: zynqmp_dma: Fix race condition in the probe
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Pull siginfo cleanups from Eric Biederman:
"Long ago when 2.4 was just a testing release copy_siginfo_to_user was
made to copy individual fields to userspace, possibly for efficiency
and to ensure initialized values were not copied to userspace.
Unfortunately the design was complex, it's assumptions unstated, and
humans are fallible and so while it worked much of the time that
design failed to ensure unitialized memory is not copied to userspace.
This set of changes is part of a new design to clean up siginfo and
simplify things, and hopefully make the siginfo handling robust enough
that a simple inspection of the code can be made to ensure we don't
copy any unitializied fields to userspace.
The design is to unify struct siginfo and struct compat_siginfo into a
single definition that is shared between all architectures so that
anyone adding to the set of information shared with struct siginfo can
see the whole picture. Hopefully ensuring all future si_code
assignments are arch independent.
The design is to unify copy_siginfo_to_user32 and
copy_siginfo_from_user32 so that those function are complete and cope
with all of the different cases documented in signinfo_layout. I don't
think there was a single implementation of either of those functions
that was complete and correct before my changes unified them.
The design is to introduce a series of helpers including
force_siginfo_fault that take the values that are needed in struct
siginfo and build the siginfo structure for their callers. Ensuring
struct siginfo is built correctly.
The remaining work for 4.17 (unless someone thinks it is post -rc1
material) is to push usage of those helpers down into the
architectures so that architecture specific code will not need to deal
with the fiddly work of intializing struct siginfo, and then when
struct siginfo is guaranteed to be fully initialized change copy
siginfo_to_user into a simple wrapper around copy_to_user.
Further there is work in progress on the issues that have been
documented requires arch specific knowledge to sort out.
The changes below fix or at least document all of the issues that have
been found with siginfo generation. Then proceed to unify struct
siginfo the 32 bit helpers that copy siginfo to and from userspace,
and generally clean up anything that is not arch specific with regards
to siginfo generation.
It is a lot but with the unification you can of siginfo you can
already see the code reduction in the kernel"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (45 commits)
signal/memory-failure: Use force_sig_mceerr and send_sig_mceerr
mm/memory_failure: Remove unused trapno from memory_failure
signal/ptrace: Add force_sig_ptrace_errno_trap and use it where needed
signal/powerpc: Remove unnecessary signal_code parameter of do_send_trap
signal: Helpers for faults with specialized siginfo layouts
signal: Add send_sig_fault and force_sig_fault
signal: Replace memset(info,...) with clear_siginfo for clarity
signal: Don't use structure initializers for struct siginfo
signal/arm64: Better isolate the COMPAT_TASK portion of ptrace_hbptriggered
ptrace: Use copy_siginfo in setsiginfo and getsiginfo
signal: Unify and correct copy_siginfo_to_user32
signal: Remove the code to clear siginfo before calling copy_siginfo_from_user32
signal: Unify and correct copy_siginfo_from_user32
signal/blackfin: Remove pointless UID16_SIGINFO_COMPAT_NEEDED
signal/blackfin: Move the blackfin specific si_codes to asm-generic/siginfo.h
signal/tile: Move the tile specific si_codes to asm-generic/siginfo.h
signal/frv: Move the frv specific si_codes to asm-generic/siginfo.h
signal/ia64: Move the ia64 specific si_codes to asm-generic/siginfo.h
signal/powerpc: Remove redefinition of NSIGTRAP on powerpc
signal: Move addr_lsb into the _sigfault union for clarity
...
Pull x86 timer updates from Thomas Gleixner:
"A small set of updates for x86 specific timers:
- Mark TSC invariant on a subset of Centaur CPUs
- Allow TSC calibration without PIT on mobile platforms which lack
legacy devices"
* 'x86-timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/centaur: Mark TSC invariant
x86/tsc: Introduce early tsc clocksource
x86/time: Unconditionally register legacy timer interrupt
x86/tsc: Allow TSC calibration without PIT
Pull x86 platform updates from Thomas Gleixner:
"The platform support for x86 contains the following updates:
- A set of updates for the UV platform to support new CPUs and to fix
some of the UV4A BAU MRRs
- The initial platform support for the jailhouse hypervisor to allow
native Linux guests (inmates) in non-root cells.
- A fix for the PCI initialization on Intel MID platforms"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86/jailhouse: Respect pci=lastbus command line settings
x86/jailhouse: Set X86_FEATURE_TSC_KNOWN_FREQ
x86/platform/intel-mid: Move PCI initialization to arch_init()
x86/platform/uv/BAU: Replace hard-coded values with MMR definitions
x86/platform/UV: Fix UV4A BAU MMRs
x86/platform/UV: Fix GAM MMR references in the UV x2apic code
x86/platform/UV: Fix GAM MMR changes in UV4A
x86/platform/UV: Add references to access fixed UV4A HUB MMRs
x86/platform/UV: Fix UV4A support on new Intel Processors
x86/platform/UV: Update uv_mmrs.h to prepare for UV4A fixes
x86/jailhouse: Add PCI dependency
x86/jailhouse: Hide x2apic code when CONFIG_X86_X2APIC=n
x86/jailhouse: Initialize PCI support
x86/jailhouse: Wire up IOAPIC for legacy UART ports
x86/jailhouse: Halt instead of failing to restart
x86/jailhouse: Silence ACPI warning
x86/jailhouse: Avoid access of unsupported platform resources
x86/jailhouse: Set up timekeeping
x86/jailhouse: Enable PMTIMER
x86/jailhouse: Enable APIC and SMP support
...
- Update the ACPICA kernel code to upstream revision 20171215 including:
* Support for ACPI 6.0A changes in the NFIT table (Bob Moore).
* Local 64-bit divide in string conversions (Bob Moore).
* Fix for a regression in acpi_evaluate_object_type() (Bob Moore).
* Fixes for memory leaks during package object resolution (Bob Moore).
* Deployment of safe version of strncpy() (Bob Moore).
* Debug and messaging updates (Bob Moore).
* Support for PDTT, SDEV, TPM2 tables in iASL and tools (Bob Moore).
* Null pointer dereference avoidance in Op and cleanups (Colin Ian King).
* Fix for memory leak from building prefixed pathname (Erik Schmauss).
* Coding style fixes, disassembler and compiler updates (Hanjun Guo,
Erik Schmauss).
* Additional PPTT flags from ACPI 6.2 (Jeremy Linton).
* Fix for an off-by-one error in acpi_get_timer_duration() (Jung-uk Kim).
* Infinite loop detection timeout and utilities cleanups (Lv Zheng).
* Windows 10 version 1607 and 1703 OSI strings (Mario Limonciello).
- Update ACPICA information in MAINTAINERS to reflect the current
status of ACPICA maintenance and rename a local variable in one
function to match the corresponding upstream code (Rafael Wysocki).
- Clean up ACPI-related initialization on x86 (Andy Shevchenko).
- Add support for Intel Merrifield to the ACPI GPIO code (Andy
Shevchenko).
- Clean up ACPI PMIC drivers (Andy Shevchenko, Arvind Yadav).
- Fix the ACPI Generic Event Device (GED) driver to free IRQs on
shutdown and clean up the PCI IRQ Link driver (Sinan Kaya).
- Make the GHES code call into the AER driver on all errors and
clean up the ACPI APEI code (Colin Ian King, Tyler Baicar).
- Make the IA64 ACPI NUMA code parse all SRAT entries (Ganapatrao
Kulkarni).
- Add a lid switch blacklist to the ACPI button driver and make it
print extra debug messages on lid events (Hans de Goede).
- Add quirks for Asus GL502VSK and UX305LA to the ACPI battery
driver and clean it up somewhat (Bjørn Mork, Kai-Heng Feng).
- Add device link for CHT SD card dependency on I2C to the ACPI
LPSS (Intel SoCs) driver and make it avoid creating platform
device objects for devices without MMIO resources (Adrian Hunter,
Hans de Goede).
- Fix the ACPI GPE mask kernel command line parameter handling
(Prarit Bhargava).
- Fix the handling of (incorrectly exposed) backlight interfaces
without LCD (Hans de Goede).
- Fix the usage of debugfs_create_*() in the ACPI EC driver (Geert
Uytterhoeven).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/eCQ
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"The majority of this is an update of the ACPICA kernel code to
upstream revision 20171215 with a cosmetic change and a maintainers
information update on top of it.
The rest is mostly some minor fixes and cleanups in the ACPI drivers
and cleanups to initialization on x86.
Specifics:
- Update the ACPICA kernel code to upstream revision 20171215 including:
* Support for ACPI 6.0A changes in the NFIT table (Bob Moore)
* Local 64-bit divide in string conversions (Bob Moore)
* Fix for a regression in acpi_evaluate_object_type() (Bob Moore)
* Fixes for memory leaks during package object resolution (Bob
Moore)
* Deployment of safe version of strncpy() (Bob Moore)
* Debug and messaging updates (Bob Moore)
* Support for PDTT, SDEV, TPM2 tables in iASL and tools (Bob
Moore)
* Null pointer dereference avoidance in Op and cleanups (Colin Ian
King)
* Fix for memory leak from building prefixed pathname (Erik
Schmauss)
* Coding style fixes, disassembler and compiler updates (Hanjun
Guo, Erik Schmauss)
* Additional PPTT flags from ACPI 6.2 (Jeremy Linton)
* Fix for an off-by-one error in acpi_get_timer_duration()
(Jung-uk Kim)
* Infinite loop detection timeout and utilities cleanups (Lv
Zheng)
* Windows 10 version 1607 and 1703 OSI strings (Mario
Limonciello)
- Update ACPICA information in MAINTAINERS to reflect the current
status of ACPICA maintenance and rename a local variable in one
function to match the corresponding upstream code (Rafael Wysocki)
- Clean up ACPI-related initialization on x86 (Andy Shevchenko)
- Add support for Intel Merrifield to the ACPI GPIO code (Andy
Shevchenko)
- Clean up ACPI PMIC drivers (Andy Shevchenko, Arvind Yadav)
- Fix the ACPI Generic Event Device (GED) driver to free IRQs on
shutdown and clean up the PCI IRQ Link driver (Sinan Kaya)
- Make the GHES code call into the AER driver on all errors and clean
up the ACPI APEI code (Colin Ian King, Tyler Baicar)
- Make the IA64 ACPI NUMA code parse all SRAT entries (Ganapatrao
Kulkarni)
- Add a lid switch blacklist to the ACPI button driver and make it
print extra debug messages on lid events (Hans de Goede)
- Add quirks for Asus GL502VSK and UX305LA to the ACPI battery driver
and clean it up somewhat (Bjørn Mork, Kai-Heng Feng)
- Add device link for CHT SD card dependency on I2C to the ACPI LPSS
(Intel SoCs) driver and make it avoid creating platform device
objects for devices without MMIO resources (Adrian Hunter, Hans de
Goede)
- Fix the ACPI GPE mask kernel command line parameter handling
(Prarit Bhargava)
- Fix the handling of (incorrectly exposed) backlight interfaces
without LCD (Hans de Goede)
- Fix the usage of debugfs_create_*() in the ACPI EC driver (Geert
Uytterhoeven)"
* tag 'acpi-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (62 commits)
ACPI/PCI: pci_link: reduce verbosity when IRQ is enabled
ACPI / LPSS: Do not instiate platform_dev for devs without MMIO resources
ACPI / PMIC: Convert to use builtin_platform_driver() macro
ACPI / x86: boot: Propagate error code in acpi_gsi_to_irq()
ACPICA: Update version to 20171215
ACPICA: trivial style fix, no functional change
ACPICA: Fix a couple memory leaks during package object resolution
ACPICA: Recognize the Windows 10 version 1607 and 1703 OSI strings
ACPICA: DT compiler: prevent error if optional field at the end of table is not present
ACPICA: Rename a global variable, no functional change
ACPICA: Create and deploy safe version of strncpy
ACPICA: Cleanup the global variables and update comments
ACPICA: Debugger: fix slight indentation issue
ACPICA: Fix a regression in the acpi_evaluate_object_type() interface
ACPICA: Update for a few debug output statements
ACPICA: Debug output, no functional change
ACPI: EC: Fix debugfs_create_*() usage
ACPI / video: Default lcd_only to true on Win8-ready and newer machines
ACPI / x86: boot: Don't setup SCI on HW-reduced platforms
ACPI / x86: boot: Use INVALID_ACPI_IRQ instead of 0 for acpi_sci_override_gsi
...
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver
PM flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of
genpd (Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the
ACPI core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal
and clean up the governor management code in the cpufreq core
(Rafael Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id
from the PSCI driver and drop dependency on arm_big_little from
the SCPI cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=dnb7
-----END PGP SIGNATURE-----
Merge tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This includes some infrastructure changes in the PM core, mostly
related to integration between runtime PM and system-wide suspend and
hibernation, plus some driver changes depending on them and fixes for
issues in that area which have become quite apparent recently.
Also included are changes making more x86-based systems use the Low
Power Sleep S0 _DSM interface by default, which turned out to be
necessary to handle power button wakeups from suspend-to-idle on
Surface Pro3.
On the cpufreq front we have fixes and cleanups in the core, some new
hardware support, driver updates and the removal of some unused code
from the CPU cooling thermal driver.
Apart from this, the Operating Performance Points (OPP) framework is
prepared to be used with power domains in the future and there is a
usual bunch of assorted fixes and cleanups.
Specifics:
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver PM
flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of genpd
(Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the ACPI
core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal and
clean up the governor management code in the cpufreq core (Rafael
Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh
Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri
Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id from
the PSCI driver and drop dependency on arm_big_little from the SCPI
cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy
Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott)"
* tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
PCI / PM: Remove spurious semicolon
cpufreq: scpi: remove arm_big_little dependency
drivers: psci: remove cluster terminology and dependency on physical_package_id
powercap: intel_rapl: Fix trailing semicolon
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / hibernate: Drop unused parameter of enough_swap
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()
cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
cpufreq: intel_pstate: Add Skylake servers support
cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
ACPI / PM: Use Low Power S0 Idle on more systems
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / domains: Don't skip driver's ->suspend|resume_noirq() callbacks
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
powercap: add suspend and resume mechanism for SOC power limit
...
Centaur CPU has a constant frequency TSC and that TSC does not stop in
C-States. But because the corresponding TSC feature flags are not set for
that CPU, the TSC is treated as not constant frequency and assumed to stop
in C-States, which makes it an unreliable and unusable clock source.
Setting those flags tells the kernel that the TSC is usable, so it will
select it over HPET. The effect of this is that reading time stamps (from
kernel or user space) will be faster and more efficent.
Signed-off-by: davidwang <davidwang@zhaoxin.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: qiyuanwang@zhaoxin.com
Cc: linux-pm@vger.kernel.org
Cc: brucechang@via-alliance.com
Cc: cooperyan@zhaoxin.com
Cc: benjaminpan@viatech.com
Link: https://lkml.kernel.org/r/1516616057-5158-1-git-send-email-davidwang@zhaoxin.com
Today 4 architectures set ARCH_SUPPORTS_MEMORY_FAILURE (arm64, parisc,
powerpc, and x86), while 4 other architectures set __ARCH_SI_TRAPNO
(alpha, metag, sparc, and tile). These two sets of architectures do
not interesect so remove the trapno paramater to remove confusion.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
* acpi-gpio:
gpio: merrifield: Add support of ACPI enabled platforms
ACPI: utils: Introduce acpi_dev_get_first_match_name()
* acpi-button:
ACPI: button: Add a LID switch blacklist and add 1 model to it
ACPI: button: Add a debug message when we're sending a LID event
* acpi-battery:
ACPI / battery: Add quirk for Asus GL502VSK and UX305LA
ACPI: battery: Drop redundant test for failure
* acpi-video:
ACPI / video: Default lcd_only to true on Win8-ready and newer machines
* acpica: (40 commits)
ACPICA: Update version to 20171215
ACPICA: trivial style fix, no functional change
ACPICA: Fix a couple memory leaks during package object resolution
ACPICA: Recognize the Windows 10 version 1607 and 1703 OSI strings
ACPICA: DT compiler: prevent error if optional field at the end of table is not present
ACPICA: Rename a global variable, no functional change
ACPICA: Create and deploy safe version of strncpy
ACPICA: Cleanup the global variables and update comments
ACPICA: Debugger: fix slight indentation issue
ACPICA: Fix a regression in the acpi_evaluate_object_type() interface
ACPICA: Update for a few debug output statements
ACPICA: Debug output, no functional change
ACPICA: Update information in MAINTAINERS
ACPICA: Rename variable to match upstream
ACPICA: Update version to 20171110
ACPICA: ACPI 6.2: Additional PPTT flags
ACPICA: Update linkage for get mutex name interface
ACPICA: Update mutex error messages, no functional change
ACPICA: Debugger: add "background" command for method execution
ACPICA: Small typo fix, no functional change
...
* acpi-pm:
platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
ACPI / PM: Use Low Power S0 Idle on more systems
ACPI / PM: Make it possible to ignore the system sleep blacklist
* pm-sleep:
PM / hibernate: Drop unused parameter of enough_swap
block, scsi: Fix race between SPI domain validation and system suspend
PM / sleep: Make lock/unlock_system_sleep() available to kernel modules
PM: hibernate: Do not subtract NR_FILE_MAPPED in minimum_image_size()
* pm-core: (29 commits)
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
PM: i2c-designware-platdrv: Optimize power management
PM: i2c-designware-platdrv: Use DPM_FLAG_SMART_PREPARE
PM / mfd: intel-lpss: Use DPM_FLAG_SMART_SUSPEND
PCI / PM: Use SMART_SUSPEND and LEAVE_SUSPENDED flags for PCIe ports
PM / wakeup: Add device_set_wakeup_path() helper to control wakeup path
PM / core: Assign the wakeup_path status flag in __device_prepare()
PM / wakeup: Do not fail dev_pm_attach_wake_irq() unnecessarily
PM / core: Direct DPM_FLAG_LEAVE_SUSPENDED handling
PM / core: Direct DPM_FLAG_SMART_SUSPEND optimization
PM / core: Add helpers for subsystem callback selection
PM / wakeup: Drop redundant check from device_init_wakeup()
PM / wakeup: Drop redundant check from device_set_wakeup_enable()
PM / wakeup: only recommend "call"ing device_init_wakeup() once
...
When ACPI Link object is enabled, the message is printed with a warning
prefix. Some test tools are capturing warning and test error types as
errors. Let's reduce the verbosity of success case.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_lpss_create_device() skips handling LPSS devices which do not have
a mmio resources in their resource list (typically these devices are
disabled by the firmware). But since the LPSS code does not bind to the
device, acpi_bus_attach() ends up still creating a platform device for
it and the regular platform_driver for the ACPI HID still tries to bind
to it.
This happens e.g. on some boards which do not use the pwm-controller
and have an empty or invalid resource-table for it. Currently this causes
these error messages to get logged:
[ 3.281966] pwm-lpss 80862288:00: invalid resource
[ 3.287098] pwm-lpss: probe of 80862288:00 failed with error -22
This commit stops the undesirable creation of a platform_device for
disabled LPSS devices by setting pnp.type.platform_id to 0. Note that
acpi_scan_attach_handler() also sets pnp.type.platform_id to 0 when there
is a matching handler for the device and that handler has no attach
callback, so we simply behave as a handler without an attach function
in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some systems don't support the ACPI_LPS0_ENTRY and ACPI_LPS0_EXIT
functions in their Low Power S0 Idle _DSM, but still expect EC
events to be processed in the suspend-to-idle state for power button
wakeup (among other things) to work. Surface Pro3 turns out to be
one of them.
Fortunately, it still provides Low Power S0 Idle _DSM with the screen
on/off functions supported, so modify the ACPI suspend-to-idle to use
the Low Power S0 Idle code path for all systems supporting the
ACPI_LPS0_ENTRY and ACPI_LPS0_EXIT or the ACPI_LPS0_SCREEN_OFF and
ACPI_LPS0_SCREEN_ON functions in their Low Power S0 Idle _DSM.
Potentially, that will cause more systems to use suspend-to-idle by
default, so some future corrections may be necessary if it leads
to issues, but let it remain more straightforward for now.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198389#add_comment
Reported-by: Valentin Manea <valy@mrs.ro>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Valentin Manea <valy@mrs.ro>
All of PMIC OpRegion drivers can't be modules, thus, convert them to use
builtin_platform_driver() macro and remove redundant MODULE_*() macros.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes the user wants to have device name of the match rather than
just checking if device present or not. To make life easier for such
users introduce acpi_dev_get_first_match_name() helper based on code
for acpi_dev_present().
For example, GPIO driver for Intel Merrifield needs to know the device
name of pin control to be able to apply GPIO mapping table to the proper
device.
To be more consistent with the purpose rename
struct acpi_dev_present_info -> struct acpi_dev_match_info
acpi_dev_present_cb() -> acpi_dev_match_cb()
in the utils.c file.
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 83f3375d6dcb3af812c91aaf47abcac9fc330527
This adds a semi-colon at the end of a macro call so that it can be
processed correctly with source code formatting tools.
Link: https://github.com/acpica/acpica/commit/83f3375d
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 69d4415360446b4a1826dab76ba0cd6d24710ddd
A couple memory leaks during resolution of individual
package elements.
Link: https://github.com/acpica/acpica/commit/69d44153
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 35a4a3ea723b3066f575e63e5f0116f7ce65e713
The public Microsoft document listing recognized OSI strings [1]
shows that these two strings were introduced.
version 1607 / Anniversary Update / "Redstone 1"
version 1703 / Creators Update / "Redstone 2"
[1] http://download.microsoft.com/download/7/e/7/7e7662cf-cbea-470b-a97e-ce7ce0d98dc2/winacpi_osi.docx
Link: https://github.com/acpica/acpica/commit/35a4a3ea
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ab9c83985e8b2b25dc1c173b753280a8d04922b5
Rename to add the standard prefix for globals.
Link: https://github.com/acpica/acpica/commit/ab9c8398
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 64ad9c69a1bd534a466e060a33c0bbf5fc9e189c
acpi_ut_safe_strncpy - copy and terminate string. Strncpy is not
guaranteed to terminate the copied string if the input is longer
than the length of the target.
No functional change.
Link: https://github.com/acpica/acpica/commit/64ad9c69
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 8519ba376636565350c3fa0db5621c61d34c34b2
Mostly cleanup/reformatting. Some restructuring.
No functional change.
Link: https://github.com/acpica/acpica/commit/8519ba37
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit c75af007d35c0afe8791ac39b7749c7442f49912
The %*s format specifier prints a string with a width indicated by an integer.
In the case of acpi_os_printf() ("%*s", acpi_gbl_nesting_level, " "),
a single space is printed to the console when acpi_gbl_nesting_level
is 0 or 1. This change increments acpi_gbl_nesting_level so that there
is one space printed when acpi_gbl_nesting_level is 0 and two spaces
printed when acpi_gbl_nesting_level is 1.
Link: https://github.com/acpica/acpica/commit/c75af007
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 9ab548ef154b992208524d61770caca90a9762be
The optional Pathname parameter inadvertently became required.
Introduced in April 2017.
Link: https://github.com/acpica/acpica/commit/9ab548ef
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 900e96a9c6c6d67c2e18e8c2576dc4742221fc71
Implement a very small indent for trace output.
Link: https://github.com/acpica/acpica/commit/900e96a9
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 04fffc50a131662f57a41ca517c75d32d2479a1c
Fix use of return macros and other debug output changes.
Link: https://github.com/acpica/acpica/commit/04fffc50
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_ec.gpe is "unsigned long", hence treating it as "u32" would expose
the wrong half on big-endian 64-bit systems. Fix this by changing its
type to "u32" and removing the cast, as all other code already uses u32
or sometimes even only u8.
Fixes: 1195a09816 (ACPI: Provide /sys/kernel/debug/ec/...)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We're seeing a lot of bogus backlight interfaces on newer machines without
a LCD such as desktops, servers and HDMI sticks. This causes userspace to
show a non-functional brightness slider in e.g. the GNOME3 system menu,
which is undesirable. And, in general, we should simply just not register
a non functional backlight interface.
Checking the LCD flag causes the bogus acpi_video backlight interfaces to
go away (on the machines this was tested on).
This change sets the lcd_only option by default on any machines which
are Win8-ready, to fix this.
This is not entirely without a risk of regressions, but video_detect.c
already prefers native-backlight interfaces over the acpi_video one
on Win8-ready machines, calling acpi_video_unregister_backlight() as soon
as a native interface shows up. This is done because the ACPI backlight
interface often is broken on Win8-ready machines, because win8 does not
seem to actually use it.
So in practice we already end up not registering the ACPI backlight
interface on (most) Win8-ready machines with a LCD panel, thus this
change does not change anything for (most) machines with a LCD panel
and on machines without a LCD panel we actually don't want to register
any backlight interfaces.
This has been tested on the following machines and fixes a bogus backlight
interface showing up there:
- Desktop with an Asrock B150M Pro4S/D3 m.b. using i5-6500 builtin gfx
- Intel Compute Stick STK1AW32SC
- Meegopad T08 HDMI stick
Bogus backlight interfaces have also been reported on:
- Desktop with Asus H87I-Plus m.b.
- Desktop with ASRock B75M-ITX m.b.
- Desktop with Gigabyte Z87-D3HP m.b.
- Dell PowerEdge T20 desktop
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1097436
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1133327
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1133329
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1133646
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull libnvdimm fixes from Dan Williams:
"These fixes are all tagged for -stable and have received a build
success notification from the kbuild robot.
- NVDIMM namespaces, configured to enforce 1GB alignment, fail to
initialize on platforms that mis-align the start or end of the
physical address range.
- The Linux implementation of the BTT (Block Translation Table) is
incompatible with the UEFI 2.7 definition of the BTT format. The
BTT layers a software atomic sector semantic on top of an NVDIMM
namespace. Linux needs to be compatible with the UEFI definition to
enable boot support or any pre-OS access of data on a BTT enabled
namespace.
- A fix for ACPI SMART notification events, this allows a userspace
monitor to register for health events rather than poll. This has
been broken since it was initially merged as the unit test
inadvertently worked around the problem. The urgency for fixing
this during the -rc series is driven by how expensive it is to poll
for this data (System Management Mode entry)"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, btt: Fix an incompatibility in the log layout
libnvdimm, btt: add a couple of missing kernel-doc lines
libnvdimm, dax: fix 1GB-aligned namespaces vs physical misalignment
libnvdimm, pfn: fix start_pad handling for aligned namespaces
acpi, nfit: fix health event notification
On Asus GL502VSK and UX305LA, ACPI incorrectly reports discharging when
battery is full and AC is plugged.
However rate_now is correct under this circumstance, hence we can use
"rate_now == 0" as a predicate to report battery full status correctly.
Link: https://bugs.launchpad.net/bugs/1482390
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The commit f6f8285132 ("pstore: pass allocated memory region back to
caller") changed the check of the return value from erst_read() in
erst_reader() in the following way:
if (len == -ENOENT)
goto skip;
- else if (len < 0) {
- rc = -1;
+ else if (len < sizeof(*rcd)) {
+ rc = -EIO;
goto out;
This introduced another bug: since the comparison with sizeof() is
cast to unsigned, a negative len value doesn't hit any longer.
As a result, when an error is returned from erst_read(), the code
falls through, and it may eventually lead to some weird thing like
memory corruption.
This patch adds the negative error value check more explicitly for
addressing the issue.
Fixes: f6f8285132 (pstore: pass allocated memory region back to caller)
Cc: All applicable <stable@vger.kernel.org>
Tested-by: Jerry Tang <jtang@suse.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The initialization of pcc_ss_data from pcc_data[pcc_ss_id] before
pcc_ss_id is being range checked could lead to an out-of-bounds array
read. This very same initialization is also being performed after
the range check on pcc_ss_id, so we can just remove this problematic
and also redundant assignment to fix the issue.
Detected by cppcheck:
warning: Value stored to 'pcc_ss_data' during its initialization is never
read
Fixes: 85b1407bf6 (ACPI / CPPC: Make CPPC ACPI driver aware of PCC subspace IDs)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some GED interrupts could be pending by the time we are doing a reboot.
Even though GED driver uses devm_request_irq() to register the interrupt
handler, the handler is not being freed on time during a shutdown since
the driver is missing a shutdown callback.
If the ACPI handler is no longer available, this causes an interrupt
storm and delays shutdown.
1. Don't use devm family of functions for IRQ registration/free
2. Keep track of the events since free_irq() requires the dev_id
parameter passed into the request_irq() function.
3. Call free_irq() on both remove and shutdown explicitly.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some Cherry Trail boards have a dependency between the SDHCI host
controller used for SD cards and an external PMIC accessed via I2C. Add a
device link between the SDHCI host controller (consumer) and the I2C
adapter (supplier).
This patch depends on a fix to devices links, namely commit 0ff26c662d
("driver core: Fix device link deferred probe"). And also either,
commit 126dbc6b49 ("PM: i2c-designware-platdrv: Clean up PM handling in
probe"), or patch "PM / runtime: Fix handling of suppliers with disabled
runtime PM".
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we have a get_match_data() callback as part of the firmware node,
implement the ACPI specific piece for it.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
OF has of_device_get_match_data() function to extract driver specific data
structure. Add a similar function for ACPI.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Merging the two adjacent conditionally built blocks makes the code
a lot more readable. And as a bonus, we drop a duplicate test when
CONFIG_ACPI_PROCFS_POWER is undefined.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The acpi_mask_gpe= kernel parameter documentation states that the range
of mask is 128 GPEs (0x00 to 0x7F). The acpi_masked_gpes mask is a u64 so
only 64 GPEs (0x00 to 0x3F) can really be masked.
Use a bitmap of size 0xFF instead of a u64 for the GPE mask so 256
GPEs can be masked.
Fixes: 9c4aa1eecb (ACPI / sysfs: Provide quirk mechanism to prevent GPE flooding)
Signed-off-by: Prarit Bharava <prarit@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The GP-electronic T701 tablet does not have a LID switch, but it
does define a LID device in its DSDT. The _LID method points to
the "\\_SB.GPO2" pin 0x18 GPIO with a pull setting of "PullDefault",
which leaves the pin floating.
This causes the ACPI button driver to cause spurious LID closed events,
causing the device to suspend while the user is using it. There is
nothing the ACPI button driver (or the gpio code) can do to fix this,
so the only solution is to add a DMI based blacklist and ignore the LID
device on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
I've been debugging some spurious suspend issues on various devices,
at least on some devices these spurious suspends are caused by surious
LID closed events being send to userspace.
Running e.g. evemu-record after noticing a spurious suspend is too late
to detect that a LID closed event it the (probable) cause of this.
This commit adds an acpi_handle_debug call to help debugging this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Middle-layer code doing suspend-time optimizations for devices with
the DPM_FLAG_SMART_SUSPEND flag set (currently, the PCI bus type and
the ACPI PM domain) needs to make the core skip ->thaw_early and
->thaw callbacks for those devices in some cases and it sets the
power.direct_complete flag for them for this purpose.
However, it turns out that setting power.direct_complete outside of
the PM core is a bad idea as it triggers an excess invocation of
pm_runtime_enable() in device_resume().
For this reason, provide a helper to clear power.is_late_suspended
and power.is_suspended to be invoked by the middle-layer code in
question instead of setting power.direct_complete and make that code
call the new helper.
Fixes: c4b65157ae (PCI / PM: Take SMART_SUSPEND driver flag into account)
Fixes: 05087360fd (ACPI / PM: Take SMART_SUSPEND driver flag into account)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Variables len and node_len are redundant and can be removed. Cleans
up clang warning: node_len = GHES_ESTATUS_NODE_LEN(len);
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the GHES code only calls into the AER driver for
recoverable type errors. This is incorrect because errors of
other severities do not get logged by the AER driver and do not
get exposed to user space via the AER trace event. So, call
into the AER driver for PCIe errors regardless of the severity
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move PCIe AER error handling code into a separate function.
Signed-off-by: Tyler Baicar <tbaicar@codeaurora.org>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Integration testing with a BIOS that generates injected health event
notifications fails to communicate those events to userspace. The nfit
driver neglects to link the ACPI DIMM device with the necessary driver
data so acpi_nvdimm_notify() fails this lookup:
nfit_mem = dev_get_drvdata(dev);
if (nfit_mem && nfit_mem->flags_attr)
sysfs_notify_dirent(nfit_mem->flags_attr);
Add the necessary linkage when installing the notification handler and
clean it up when the nfit driver instance is torn down.
Cc: <stable@vger.kernel.org>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Fixes: ba9c8dd3c2 ("acpi, nfit: add dimm device notification support")
Reported-by: Daniel Osawa <daniel.k.osawa@intel.com>
Tested-by: Daniel Osawa <daniel.k.osawa@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is a variable name mismatch in acpi_ut_strtoul_multiply64()
between the ACPICA code in the kernel and the corresponding upstream
code which may be problematic if changes to this particular piece of
code are made upstream and ported to Linux, so rename the variable
in question to match its name in the upstream code.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI code supporting system transitions to sleep states uses
an internal blacklist to apply special handling to some machines
reported to behave incorrectly in some ways.
However, some entries of that blacklist cover problematic as well as
non-problematic systems, so give the users of the latter a chance to
ignore the blacklist and run their systems in the default way by
adding acpi_sleep=nobl to the kernel command line.
For example, that allows the users of Dell XPS13 9360 systems not
affected by the issue that caused the blacklist entry for this
machine to be added by commit 71630b7a83 (ACPI / PM: Blacklist Low
Power S0 Idle _DSM for Dell XPS13 9360) to use suspend-to-idle with
the Low Power S0 Idle _DSM interface which in principle should be
more energy-efficient than S3 on them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for DPM_FLAG_LEAVE_SUSPENDED to the ACPI PM domain by
making it (a) set the power.may_skip_resume status bit for devices
that, from its perspective, may be left in suspend after system
wakeup from sleep and (b) return early from acpi_subsys_resume_noirq()
for devices whose remaining resume callbacks during the transition
under way are going to be skipped by the PM core.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPICA commit cb9a3906ec35da7a6e0b8972f8e6e7895e59c208
Always enable the function.
Link: https://github.com/acpica/acpica/commit/cb9a3906
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 22f2b0beb45d277841ed02bc613df1009e5b20cf
Add mutex name on certain acquire/release errors.
Link: https://github.com/acpica/acpica/commit/22f2b0be
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit d7b44738a48caa9f669b8dbf0024d456711aec31
Allows a single task to execute in the background, while control
returns to the debugger prompt.
Also, cleanup the debugger help screen.
Link: https://github.com/acpica/acpica/commit/d7b44738
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f8ca5db30605467b851f86d152079631c27eeca8
Link: https://github.com/acpica/acpica/commit/f8ca5db3
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit b09c8d7bdc8c5a3db0a8d38bfd6182c023885e12
1) Emit the full pathname (scope+name) instead of just the name
2) For AE_ALREADY_EXISTS and AE_NOT_FOUND, use the "firmware error"
string to point to the true problem.
Link: https://github.com/acpica/acpica/commit/b09c8d7b
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 8070a23749f1c2eedec313f42f564b5375054137
Link: https://github.com/acpica/acpica/commit/8070a237
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 24dd370b14711b7b3f31d7ca6326f9e0bd177c4e
AE_TIME is seen to be returned from the EC driver/handler so
often that an additional error message is added to help
clarify the problem.
Link: https://github.com/acpica/acpica/commit/24dd370b
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit b2858b2cc83e1481950a2c976f62d4e1d758bc85
Changes line prefix from "ACPI Exception" to simply "ACPI Error"
to match the ACPI_ERROR macro. ACPI_EXCEPTION takes the ACPI status
as an argument, decodes and displays it along with the error
message.
Link: https://github.com/acpica/acpica/commit/b2858b2c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit f230f4df26d07b97ef00be39156ecee64250447d
On 32-bit platforms, 64-bit divide often requires a library
function which may not be present in the build.
Link: https://github.com/acpica/acpica/commit/f230f4df
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit b49a0e1e26f3c61df7113f18f441c83739eb5514
It's reported in Linux community that change to utmath.c contains a style
problem:
[.../utmath.c:137]: (style) Same expression on both sides of '^='.
[.../utmath.c:174]: (style) Same expression on both sides of '^='.
This patch fixes this problem. ACPICA BZ 1422, reported by David Binderman,
fixed by Lv Zheng.
Link: https://github.com/acpica/acpica/commit/b49a0e1e
Link: https://bugs.acpica.org/show_bug.cgi?id=1422
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit aa866a9b4f24bbec9f158d10325b486d7d12d90f
The declaration External (ABCD.EFGH) creates two nodes in the namespace: ABCD
and EFGH where ABCD is marked as an implicit external node. ABCD is labeled as
implicit because there does not exist a specific External (ABCD) declaration.
Before this change, the declaration External (ABCD.EFGH) and
External (ABCD.EFGH.IJKL) creates the namespace nodes ABCD, EFGH, and IJKL
where ABCD and EFGH are labeled as implicit external nodes. This is incorrect.
The only implicit node should be ABCD because EFGH and IJKL are explicit nodes.
This change fixes the labeling procecess of external op namespace nodes so that
nodes are properly labeled as implicit external.
Due to this commit, the below ASL code results in a compilation error.
definition_block ("DSDT.aml", "DSDT", 0x02, "INTEL", "BDW ", 0x0)
{
External(\_SB.PCI0.GFX0, device_obj)
External(\_SB.PCI0.GFX0.ALSI)
Scope(\_SB)
{
Device(PCI0)
{
Device(GFX0)
{
Name(_ADR, 0x00020000)
}
}
}
}
Link: https://github.com/acpica/acpica/commit/aa866a9b
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 336131640a1574b86240b32eca3150195f9270d6
Common option for all tools.
Link: https://github.com/acpica/acpica/commit/33613164
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit e017213698374e01225f641ba0917516d8e91427
More appropriately renamed to AE_AML_LOOP_TIMEOUT, now that
a real timer is used for the implementation.
Link: https://github.com/acpica/acpica/commit/e0172136
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit 9605023e7e6d1f05581502766c8cf2905bcc03d9
This patch implements a new infinite loop detection mechanism to replace
the old one, it uses acpi_os_get_timer() to limit loop execution into a
determined time slice.
This is useful in case some hardware/firmware operations really require the
AML interpreter to wait while the old mechanism could expire too fast on
recent machines.
The new mechanism converts old acpi_gbl_max_loop_iterations to store the user
configurable value for the new mechanism in order to allow users to be
still able to configure this value for acpiexec via command line. This
patch also removes wrong initilization code of acpi_gbl_max_loop_iterations
accordingly (it should have been initialized by ACPI_INIT_GLOBAL, and the
default value is also properly tuned for acpiexec). Reported by M. Foronda,
fixed by Lv Zheng.
Link: https://github.com/acpica/acpica/commit/9605023e
Link: https://bugzilla.kernel.org/show_bug.cgi?id=156501
Reported-by: M. Foronda <josemauricioforonda@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
