Only 1st generation chips do provide USB interrupts, so do not try to
setup interrupts for newer chips (8192eu and 8723bu).
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8723bu, like the 8192eu, can also handle 1024 byte block writes.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement first stab at parsing the 8723bu's efuse.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This provides initial detection of 8723bu devices, and selects the
correct firmware image to load.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The newer generation chips have different interrupt registers.
Initialize this correct registers on 8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 8192eu (and some other parts) will report an incorrect USB OUT
EP. This tells the chip to drop it - as per the vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The logic for testing auto load failure in rtl8xxxu_auto_llt_table()
was inverted.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To match the flow of the vendor driver, move the LLT init to after the
firmware is started.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reorganizes the device initialization to init page boundaries
before starting the firmware. This matches the flow in the 8192eu
vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips can auto load the LLT table, it is no longer necessary to
build it manually in the driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements the rtl8192eu power on sequence, and splits it off
from the rtl8192cu/rtl8723au power on sequence.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rtl8192eu can handle 1024 byte block writes, unlike it's
predecessors (8192cu/8188cu).
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This identifies the chip vendors correctly and also picks the correct
firmware for rtl8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is the start of 8192eu support. For now just detect the device
and parse the efuse.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch reports the following warning:
CHECK drivers/net/wireless/realtek/rtlwifi/rc.c
drivers/net/wireless/realtek/rtlwifi/rc.c:144 _rtl_rc_rate_set_series() warn: impossible condition '(wireless_mode == 256) => (0-255 == 256)'
This warning arises because commit acc6907b87a9 ("rtlwifi: Fix warning
from ieee80211_get_tx_rates() when using 5G") now checks the wireless
mode for WIRELESS_MODE_AC_ONLY (BIT(8)) in _rtl_rc_rate_set_series().
As a result, all quantities used to store the wireless mode must be u16.
This patch also reorders struct rtl_sta_info to save a little space.
Fixes: d76d65fd26 ("rtlwifi: fix broken VHT support")
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
passing rtl_stats by value is inefficient; the structure is over 300
bytes in size and generally just one field (packet_report_type)
is being accessed, so the pass by value is a relatively large overhead.
This change just affects just the rx_command_packet calls.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Routine rtl_addr_delay() uses delay statements in code that can
sleep. To improve system responsiveness, the various delay statements
are changed.
In addition, routines rtl_rfreg_delay() and rtl_bb_delay() are
rewritten to use the code in rtl_addr_delay() for most of their
input values.
Suggested-by: Byeoungwook Kim <quddnr145@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When driver rtl8821ae is loaded but not connected to any AP, it logs
a "firmware not ready to run" message roughly once a minute. To
eliminate logging this massage under normal debug conditions, the
degug level needed to print this message is increased.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are several copies of the 5G channel tables in this driver. These
are removed so that the tables in the core will be used. This change
also removes a useless message of "Channel 163 in Group not found".
The number of possible 5G channels was reduced from 54 to a better
value of 49 during the conversion.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver defines its own set of channel tables for the 5G band. With
this change, it will use those of the core.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver defines its owh copy of the 5G channels. Change it to use
the common definitions.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are 3 drivers in this family that have 5G radios. Each of them
defines local copies of the available channels. This patch adds the
two arrays to the core driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips have RF registers beyond the original 0x3f address.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All chips, except for 8812 require BIT(0) for resetting the MCU IO
wrapper. 8723b requires a more complicated reset sequence, so it will
need a custom reset function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 documentation says, the ieee80211_ops.start callback "must turn on
frame reception (for possibly enabled monitor interfaces.)". If not a single
monitor interface does not receive data frames.
Similarly we should not change the data reception based on the association
state.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add comments describing how REG_RXFLTMAP0, REG_RXFLTMAP1 and REG_RXFLTMAP2
work.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Monitor mode is enabled by handling the filter flags we get from mac80211 in
rtl8xxxu_configure_filter() and writing them to the RCR register.
By handling the filters, we can also stop setting the BSSID filters in the
association event.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl8192cu driver doesn't read/write the REG_EFUSE_TEST register.
Neither does the rtl8188eu driver. Do it only for multifunc devices
RTL8723AU/RTL8723BU.
Signed-off-by: Jakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was a leftover from the vendor driver that was never utilized.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We need to reset the 8051 in order for it to launch the fw on the
rtl8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In rtl8xxxu_load_firmware() check the return value of kmemdup() and
error out with -ENOMEM in case of NULL to prevent a NULL pointer
dereference.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
