Add GPIO DT node and pinmux entries for DA850 EVM. GPIO is
configurable differently on different boards. So add GPIO
pinmuxing in dts file.
Signed-off-by: KV Sujith <sujithkv@ti.com>
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add ethernet device tree node information and pinmux for mii to da850 by
providing interrupt details and local mac address.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add mdio device tree node information to da850 by
providing register details and bus frequency of mdio.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Replace /include/ by #include for da850 device tree files, in order to
use the C pre-processor, making use of #define features possible.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Enable m25p64 SPI flash support on da850-EVM. Also
add partition information of SPI flash.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add tps6507x regulator device tree data to da850-evm by
adding regulator consumers with tightened constraints
and regulator-name.TPS6507x regulator handle can be obtained
by using this regulator name.
Regulator constraints are added as per da850 board file.
Regulator names are given as per maximum output voltage the
regulator is capable to provide.
for e.g. regulator name for dcdc1 is "VDCDC1_3.3V".
Also, add tps6507x PMIC I2C slave device under I2C0 node.
Tested on da850-evm.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add I2C0 device tree and pin muxing information to da850-evm.
Also, add OF_DEV_AUXDATA for I2C0 controller driver in da850
board dt file to use I2C0 clock.
Verified i2c0 node gets created in sys class interface as
"/sys/class/i2c-dev/i2c-0/subsystem/i2c-0".
nsekhar@ti.com: tested using i2cdetect and i2cdump.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add NAND driver DT node and related pinctrl DT data to export NAND
functionality on da850 evm.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
For DT, DaVinci platform can use pinctrl-single driver for handling
padconf registers.
Enable PINCTRL Kconfig for MACH_DA8XX_DT platform. Add required
pinctrl DT entries in da850 dts file.
Test procedure
1)Populate DT file with NAND node information.
2)Populate board DT file with pinmux information for NAND.
3)Boot and confirm NAND is detected by the kernel.
4)cat /proc/mtd to show partitions.
Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
