Add PF driver for NFP4000 and NFP6000.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF services multiple ports using single PCI device therefore
IRQs can no longer be allocated in the netdev code. Lower
portion of the driver has to allocate the IRQs and hand them
out to ports.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF driver will support multiple ports per PCI device, add port
number to DebugFS paths.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP Service Processor (NSP) is an ARM core inside the chip which
is responsible for management and control functions. Add support
for chip reset, FW load and external module access using the NSP.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for using application FW symbol table to look up
location of information in device memory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIP is a vector of information which linker can optionally include
in application firmware. It will be used to retrieve the location
of symbol tables.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFFW info is a resource which contains information about
the loaded application firmware. Add code which will allow
us to decode it and retrieve MIP location.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hwinfo is a simple key=value store of information which is read
from the flash and populated during chip power on. Add code to
look up information in it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource table is an array placed in a well defined location
in device's memory which describes device resources and contains
locks which have to be acquired to use them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command Push Pull is the name of NFP's network on a chip.
PCIe PF can access the interconnect through a number of mappings
controlled via Base Access Registers. BARs allow the PF to issue
pretty much any command or address any memory on the chip.
Add appropriate logic and a handful of helper for simple operations
like reading scalars from memories.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for the PF driver is about to be added and will share
much of the code. When the VF driver was added we planned to
maintain the PF driver as a separate module but have decided
that for our simple use case just maintaining a single module
is more reasonable. Rename the driver to just "nfp" and update
the Kconfig.
While at it remove latent references to NFP3200.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking at runtime that a value will fit inside
a specified field/mask.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice and only for tx 0,
it's supposed to be done in netdev_start_xmit() and per tx queue.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration
Add linux/module.h to both these files.
drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant
Add linux/moduleparam.h to this file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]
Add linux/phy_fixed.h to mvneta.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fman/fman_memac.c:519:21: error: dereferencing pointer to incomplete type 'struct fixed_phy_status'
Add linux/phy_fixed.h to fman_memac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/broadcom/bgmac.c:1015:17: error: dereferencing pointer to incomplete type 'struct mii_bus'
drivers/net/ethernet/broadcom/bgmac.c:1185:2: error: implicit declaration of function 'phy_start' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1198:2: error: implicit declaration of function 'phy_stop' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1239:9: error: implicit declaration of function 'phy_mii_ioctl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1389:28: error: 'phy_ethtool_get_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1390:28: error: 'phy_ethtool_set_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1403:13: error: dereferencing pointer to incomplete type 'struct phy_device'
drivers/net/ethernet/broadcom/bgmac.c:1417:3: error: implicit declaration of function 'phy_print_status' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1424:26: error: storage size of 'fphy_status' isn't known
drivers/net/ethernet/broadcom/bgmac.c:1424:9: error: variable 'fphy_status' has initializer but incomplete type
drivers/net/ethernet/broadcom/bgmac.c:1425:11: warning: excess elements in struct initializer
drivers/net/ethernet/broadcom/bgmac.c:1425:3: error: unknown field 'link' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1426:12: note: in expansion of macro 'SPEED_1000'
drivers/net/ethernet/broadcom/bgmac.c:1426:3: error: unknown field 'speed' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1427:13: note: in expansion of macro 'DUPLEX_FULL'
drivers/net/ethernet/broadcom/bgmac.c:1427:3: error: unknown field 'duplex' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1432:12: error: implicit declaration of function 'fixed_phy_register' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1432:31: error: 'PHY_POLL' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1438:8: error: implicit declaration of function 'phy_connect_direct' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1439:6: error: 'PHY_INTERFACE_MODE_MII' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1521:2: error: implicit declaration of function 'phy_disconnect' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1541:15: error: expected declaration specifiers or '...' before string constant
Add linux/phy.h to bgmac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
phy_interface_t phy_interface;
^~~~~~~~~~~~~~~
Add linux/phy.h to macb.h
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW does not understand ETH_P_ALL. So treat this special case differently
and translate to 0/0 key/mask. That will allow HW to match all ethertypes.
Fixes: 7aa0f5aa90 ("mlxsw: spectrum: Implement TC flower offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to update mc_disabled from switchdev attr
SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_port_orig_get returns the vport from the physical
port if needed, based on the original device.
This patch addresses the case where the original device is a bridge.
If it is vlan unaware bridge, it returns the matching vport. If it is vlan
aware bridge, there is no matching vport, and it returns the original port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decision whether to flood a multicast packet to a port dependent
on three flags: mc_disabled, mc_router_port, mc_flood.
If mc_disabled is on, the port will be flooded according to mc_flood,
otherwise, according to mc_router_port. To accomplish that, add those
flags into the mlxsw_sp_port struct and update the mc flood table
accordingly.
Update mc_router_port by switchdev attribute
SWITCHDEV_ATTR_ID_PORT_MC_ROUTER_PORT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break the bm (broadcast-multicast) into two tables, one for broadcast
(and link local multicast that behaves like bc) and one for unknown
multicasts.
Add a bool into mlxsw_sp_port named mc_flood that reflect the value this
port should have in the mc flood table (currently, always 1);
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user that wants many bridges will use 1.Q bridge which are scalable.
One can have as many 1.Q bridges as vfids.
This patch sets their number to 1k, which is a reasonably large number.
This change is done here because the next patches will add a new flood
table, and without it, it will increase the overall size of the flood
tables dramatically.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a per port flood update function only for the UC
table. Make the function more generic by changing the table type to be
an input.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the flood set function can't operate on only one table, but
sets both uc_flood and mb_flood together.
This patch creates a function that sets the flood state per table.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon the reception of an ENTRY_REPLACE notification, resolve the FIB
node corresponding to the prefix and length and insert the new route
before the first matching entry.
Since the notification also signals the deletion of the replaced route,
delete it from the driver's cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new route is appended, it's placed after existing routes sharing
the same parameters (prefix, length, table ID, TOS and priority).
While the device supports only one route with the same prefix and length
in a single table, it's important to correctly place the appended route
in the driver's cache, as when a route is deleted the next one is
programmed into the device.
Following the reception of an ENTRY_APPEND notification, resolve the
FIB node corresponding to the prefix and length and correctly place the
new entry in its entry list.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, routes are indexed in a routing table based on the prefix
and its length. This is in contrast to the kernel's FIB where several
FIB aliases can exist with these parameters being identical. In such
cases, the routes will be sorted by table ID (LOCAL first, then MAIN),
TOS and finally priority (metric).
During lookup, these routes will be evaluated in order. In case the
packet's TOS field is non-zero and a FIB alias with a matching TOS is
found, then it's selected. Otherwise, the lookup defaults to the route
with TOS 0 (if it exists). However, if the requested scope is narrower
than the one found, then the lookup continues.
To best reflect the kernel's datapath we should take the above into
account. Given a prefix and its length, the reflected route will always
be the first one in the FIB alias list. However, if the route has a
non-zero TOS then its action will be converted to trap instead of
forward, since we currently don't support TOS-based routing. If this
turns out to be a real issue, we can add support for that using
policy-based switching.
The route's scope can be effectively ignored as any packet being routed
by the device would've been looked-up using the widest scope (UNIVERSE).
To achieve that we need to do two changes. Firstly, we need to create
another struct (FIB node) that will hold the list of FIB entries sharing
the same prefix and length. This struct will be hashed using these two
parameters.
Secondly, we need to change the route reflection to match the above
logic, so that the first FIB entry in the list will be programmed into
the device while the rest will remain in the driver's cache in case of
subsequent changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the host info config to be the first admin command that is executed.
This change require the driver to remove the 'feature check'
from host info configuration flow.
The check is removed since the supported features bitmask field
is retrieved only after calling ENA_ADMIN_DEVICE_ATTRIBUTES admin command.
If set host info is not supported an error will be returned by the device.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeouts were too agressive and sometimes cause false alarms.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion descriptors are accessed from the driver and from the device.
To avoid reading the old value, use READ_ONCE macro.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not unamsk interrupts if we are in busy poll mode.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ena driver detects that the device is not behave as expected,
it tries to reset the device.
The reset flow calls ena_down, which will frees all the resources
the driver allocates and then it will reset the device.
This flow can cause memory corruption if the device is still writes
to the driver's memory space.
To overcome this potential race, move the reset before the device
resources are freed.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_get_stat64() can be called from atomic context, but the current
implementation sends an admin command to retrieve the statistics from
the device. This admin command can sleep.
This patch re-factors the implementation of ena_get_stats64() to use
the {rx,tx}bytes/count from the driver's inner counters, and to obtain
the rx drop counter from the asynchronous keep alive (heart bit)
event.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA default hash configures IPv4_frag hash twice instead of
configure non-IP packets.
The bug caused IPv4 fragmented packets to be calculated based on
L2 source and destination address instead of L3 source and destination.
IPv4 packets can reach to the wrong Rx queue.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_flow_data_to_flow_hash and ena_flow_hash_to_flow_type
treat the ena_flow_hash_to_flow_type enum as power of two values.
Change the values of ena_admin_flow_hash_fields to be power of two values.
This bug effect the ethtool set/get rxnfc.
ethtool will report wrong values hash fields for get and will
configure wrong hash fields in set.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENA driver tries to open a queue per vCPU.
To determine how many vCPUs the instance have it uses num_possible_cpus()
while it should have use num_online_cpus() instead.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove NETIF_F_NTUPLE from netdev->features.
The ENA device driver does not support ntuple filtering.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define ndo_features_check. Hw supports offload only for ipv4 inner and
ipv4 outer pkt.
Code refactor for setting inner tcp pseudo csum.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defines enic_udp_tunnel_add/del for configuring vxlan tunnel offload.
enic supports offload of only one ipv4/udp port.
There are two modes that fw supports for vxlan offload.
mode 0: fcoe bit is set for encapsulated packet. fcoe_fc_crc_ok is set
if checksum of csum is ok. This bit is or of ip_csum_ok and
tcp_udp_csum_ok
mode 2: BIT(0) in rss_hash is set if it is encapsulated packet.
BIT(1) is set if outer_ip_csum_ok/
BIT(2) is set if outer_tcp_csum_ok
tcp_udp_csum_ok/ipv4_csum_ok is set if inner csum is OK.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds devcmds needed for vxlan offload. Implement 3 new devcmd
overlay_offload_ctrl: enable/disable offload
overlay_offload_cfg: update offload udp port number
get_supported_feature_ver: get hw supported offload version. Each
version has different bitmap for csum_ok/encap
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the set_ringparam method, which allows the user to specify
the size of the TX and RX descriptor rings. The values are constrained
to the limits of the hardware.
Since the driver does not use separate queues for mini or jumbo frames,
attempts to set those values are rejected.
If the interface is already running when the setting is changed, then
the interface is reset.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the get_regs_len and get_regs ethtool methods. The driver
returns the values of selected hardware registers.
The make the register offsets known to emac_ethtool, the the register
offset macros are all combined into one header file. They were
inexplicably and arbitrarily split between two files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_udp_tunnel_{add,del} to update the NIC's list of VXLAN and
GENEVE UDP ports. Also reset the port list to empty on driver load and
on driver unload, with appropriate flag set on the unload case.
These port numbers are used for RX inner checksum offload, and in future
will also be used for TX inner checksum offload and encapsulated TSO.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
