With the introduction of hwmod module clocks, the name of the hwmod
main clk may not be available before hwmod setup, as hwmod setup
may lookup the main clock dynamically based on the hwmod name.
Thus, change the order of hwmod setup and main clock handling for
the timer code, to make sure the main clock is going to be
available.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A few platforms are currently missing clocksource_probe() completely
in their time_init functionality. On OMAP3430 for example, this is
causing cpuidle to be pretty much dead, as the counter32k is not
going to be registered and instead a gptimer is used as a clocksource.
This will tick in periodic mode, preventing any deeper idle states.
While here, also drop one unnecessary check for populated DT before
existing clocksource_probe() call.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Updates for new platform support:
- New platform: Tango4 from Sigma Designs.
- Broadcom BCM2836 (Raspberry Pi 2 SoC)
- Enable cpufreq on Freescale i.MX7D
- Rockchip: SMP support for rk3036, general support for rk3228
- SMP support on Broadcom Kona and NSP
- Cleanups for OMAP removing legacy IOMMU data
+ a bunch of misc fixes and tweaks for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FP4V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"Updates for new platform support:
- New platform: Tango4 from Sigma Designs.
- Broadcom BCM2836 (Raspberry Pi 2 SoC)
- Enable cpufreq on Freescale i.MX7D
- Rockchip: SMP support for rk3036, general support for rk3228
- SMP support on Broadcom Kona and NSP
- Cleanups for OMAP removing legacy IOMMU data
+ a bunch of misc fixes and tweaks for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: tango: Fix UP build issues
ARM: tango: pass ARM arch level for smc.S
ARM: bcm2835: Add Kconfig support for bcm2836
ARM: OMAP2+: Add support for dm814x and dra62x usb
ARM: OMAP2+: Add mmc hwmod entries for dm814x
ARM: OMAP2+: Update 81xx clock and power domains for default, active and sgx
ARM: OMAP2+: Fix SoC detection for dra62x j5-eco
ARM: tango4: Initial platform support
ARM: bcm2835: Add a compat string for bcm2836 machine probe
dt-bindings: Add root properties for Raspberry Pi 2
ARM: imx: select SRC for i.MX7
ARM: uniphier: select PINCTRL
ARM: OMAP2+: Remove device creation for omap-pcm-audio
ARM: OMAP1: Remove device creation for omap-pcm-audio
ARM: rockchip: enable support for RK3228 SoCs
ARM: rockchip: use const and __initconst for rk3036 smp_operations
ARM: zynq: Select ARCH_HAS_RESET_CONTROLLER
ARM: BCM: Add SMP support for Broadcom 4708
ARM: BCM: Add SMP support for Broadcom NSP
ARM: BCM: Clean up SMP support for Broadcom Kona
...
System will misbehave in the following case:
- AM43XX only build (UP);
- CONFIG_CPU_IDLE=y
- ARM TWD timer enabled and selected as clockevent device.
In the above case, It's expected that broadcast timer will be used as
backup timer when CPUIdle will put MPU in low power states where ARM
TWD will stop and lose its context. But, the CONFIG_SMP might not be
selected when kernel is built for AM43XX SoC only and, as result,
GENERIC_CLOCKEVENTS_BROADCAST option will not be selected also. This
will break CPUIdle and System will stuck in low power states.
Hence, fix it by selecting GENERIC_CLOCKEVENTS_BROADCAST option for
AM43XX SoCs always and add empty tick_broadcast() function
implementation - no need to send any IPI on UP. After this change
timer1 will be selected as broadcast timer the same way as for SMP,
and CPUIdle will work properly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Timer 12 on DRA7 SoCs is reserved for secure usage on high-secure (HS)
devices. The timer cannot be used by the kernel on HS devices, but is
available on regular general purpose (GP) devices. This is similar to the
behavior on OMAP3 devices, so extend the logic used in commit ad24bde8f1
("ARM: OMAP3: Dynamically disable secure timer nodes for secure devices")
to remove the secure timer on DRA7xx SoCs at run-time based on the SoC
device type.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Again we have a sizable (but not huge) cleanup branch with a net delta of about
-3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now gone
completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the above are
the major pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uI7R
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
now that we have a working 32k clocksource driver,
we can limit HWMOD usage to non-DT boots and rely
on clocksource_of_init() every time we boot
with DT.
While at that, also make sure that we don't disable
the 32-counter device so it gets probed by its driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this function is not only about the 32k sync
timer, it's OMAP's generic init_time implementation.
Let's rename it to make that detail easier to
notice.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If booting with DT, let's make sure to always
call clocksource_of_init() as this will make
it easier to move timer code to drivers/clocksource
in the future.
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of constantly defining a small wrapper
around __omap_sync32k_timer_init(), let's define
a generic one which can be used by all OMAPs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
__omap_sync32k_timer_init(), now takes the clock
source as a parameter. This means we no longer need
__omap_gptimer_init().
Note that __omap_sync32k_timer_init() will be
renamed in a follow-up patch as it's not longer 32k
source specific.
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, __omap_gptimer_init() and
__omap_sync32k_timer_init() are essentially
the same thing, but __omap_gptimer_init() wants
to always use gptimer.
Instead of forcing all those devices to pass
a use_gptimer cmdline argument, we add a new
function argument to __omap_sync32k_timer_init()
in preparation to deleting __omap_gptimer_init().
On a follow-up patch, we will remove uses of
__omap_gptimer_init() and replace them with
__omap_sync32k_timer_init() and pass the last
argument as true.
Signed-off-by: Felipe Balbi <balbi@ti.com>
those macros just make it a lot more difficult
to grep around and actually find similarities.
In this patch, we will simply remove them and
replace with actual functions and later commits
will come to further clean this up.
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap4_local_timer_init() can be used by other
platforms as is. At least AM437x wants to use
it. Instead of making omap4-only and providing
a stub for builds without OMAP4, we can just
make sure that function is always available
for all SoCs that need it.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Seeing the 'of' characters in a symbol that is being called from
ACPI seems to freak out people. So let's do a bit of pointless
renaming so that these folks do feel at home.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When bringing up a new SoC we needlessly prevent booting at timer
init if timer clock_set_parent fails. This can fail if the system
is booting on bootloader configured PLL values until the clock
framework driver for the PLL is implemented.
Let's just WARN instead, this will provide helpful information
for anybody bringing up a new SoC what needs to be fixed.
This allows to boot dm814x that's still missing the PLL driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
This series adds:
- I/O wakeup support for AM43xx
- register lock and unlock support to the hwmod code (needed for the RTC
IP blocks on some chips)
- several fixes for sparse warnings and an unnecessary null pointer test
- a DRA7xx clockdomain configuration workaround, to deal with some hardware
bugs
Basic build, boot, and PM tests are here:
http://www.pwsan.com/omap/testlogs/hwmod-prcm-for-v4.3/20150723080012/
Since I do not have an AM43xx or DRA7xx device, I can't test on those
platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dZvv
-----END PGP SIGNATURE-----
Merge tag 'for-v4.3/omap-hwmod-prcm-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.3/soc
ARM: OMAP2+: PRCM and hwmod changes for v4.3
This series adds:
- I/O wakeup support for AM43xx
- register lock and unlock support to the hwmod code (needed for the RTC
IP blocks on some chips)
- several fixes for sparse warnings and an unnecessary null pointer test
- a DRA7xx clockdomain configuration workaround, to deal with some hardware
bugs
Basic build, boot, and PM tests are here:
http://www.pwsan.com/omap/testlogs/hwmod-prcm-for-v4.3/20150723080012/
Since I do not have an AM43xx or DRA7xx device, I can't test on those
platforms.
Migrate omap2 driver to the new 'set-state' interface provided by
clockevents core, the earlier 'set-mode' interface is marked obsolete
now.
This also enables us to implement callbacks for new states of clockevent
devices, for example: ONESHOT_STOPPED.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Inspired by a patch from Felipe Balbi <balbi@ti.com>, we can
now get rid of most the code in omap4_local_timer_init.
Omap4 is now device tree only.. And we have not properly supported
omap4 ES1.0 revision for a really long time AFAIK.
Let's just remove all that code to simplify things. This assumes
we have arm,cortex-a9-twd-timer entry in the omap4.dtsi file, which
we do.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The of_node_put() function tests whether its argument is NULL and then
returns immediately if so. Furthermore, the kerneldoc for
of_node_put() explicitly supports passing in a NULL pointer as its
argument. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
[paul@pwsan.com: dropped the omap_device.c and omap_hwmod.c changes for
now, edited the commit message accordingly and to note the documented
"contract"]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
With recent changes to use determine_rate, the comparison of two
clocks won't work without clk_is_match that does __clk_get_hw
on the clocks first.
As we've been unconditionally already calling clk_set_parent
already because of the bogus comparison, let's just remove the
check as suggested by Stephen Boyd <sboyd@codeaurora.org>.
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Here's a small collection of fixes accrued during the last release that weren't
considered severe enough to merge during the -rc series.
A few of these are around resurrecting TI81xx support that's been broken for
quite a while, the rest are smaller fixes -- most for PXA but a few across
the board.
There are also some updates to MAINTAINERS here, in particular for Broadcom
platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YCX1
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"Here's a small collection of fixes accrued during the last release
that weren't considered severe enough to merge during the -rc series.
A few of these are around resurrecting TI81xx support that's been
broken for quite a while, the rest are smaller fixes -- most for PXA
but a few across the board.
There are also some updates to MAINTAINERS here, in particular for
Broadcom platforms"
* tag 'fixes-non-critical-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
MAINTAINERS: fix git repositories for Broadcom SoCs
ARM: pxa: fix broken isa interrupts for zeus and viper
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL enabled on UART3
ARM: OMAP: DRA7: hwmod: Make gpmc software supervised as the smart idle is broken
ARM: AM43xx: hwmod: set DSS submodule parent hwmods
ARM: OMAP2+: hwmod: print error if wait_target_ready() failed
MAINTAINERS: add maintainer for OMAP hwmod data
ARM: OMAP2+: Disable omap3 PM init for ti81xx
ARM: OMAP2+: Fix reboot for 81xx
ARM: OMAP2+: Fix dm814 and dm816 for clocks and timer init
ARM: OMAP2+: Fix ti81xx class type
ARM: OMAP2+: Fix ti81xx devtype
ARM: OMAP2+: Fix error handling for omap2_clk_enable_init_clocks
MAINTAINERS: add a git entry for BMIPS-based BCM7xxx SoCs
MAINTAINERS: add a git entry for BCM7xxx ARM-based SoCs
MAINTAINERS: update Broadcom Cygnus SoC git tree
MAINTAINERS: move BCM63xx ARM-based SoCs git tree
hx4700: regulator: declare full constraints
ARM: pxa: add regulator_has_full_constraints to spitz board file
ARM: pxa: add regulator_has_full_constraints to poodle board file
...
Fix dm814 and dm816 clocks and timer init.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Errata i856 for the AM572x (DRA7xx) points out that the 32.768KHz external
crystal is not enabled at power up. Instead the CPU falls back to using
an emulation for the 32KHz clock which is SYSCLK1/610. SYSCLK1 is usually
20MHz on boards so far (which gives an emulated frequency of 32.786KHz),
but can also be 19.2 or 27MHz which result in much larger drift.
Since this is used to drive the master counter at 32.768KHz * 375 /
2 = 6.144MHz, the emulated speed for 20MHz is of by 570ppm, or about 43
seconds per day, and more than the 500ppm NTP is able to tolerate.
Checking the CTRL_CORE_BOOTSTRAP register can determine if the CPU
is using the real 32.768KHz crystal or the emulated SYSCLK1/610, and
by known that the real counter frequency can be determined and used.
The real speed is then SYSCLK1 / 610 * 375 / 2 or SYSCLK1 * 75 / 244.
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The switch statement of the possible list of SYSCLK1 frequencies is
missing a 0 in 4 out of the 7 frequencies.
Fixes: fa6d79d276 ("ARM: OMAP: Add initialisation for the real-time counter")
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
of_device_ids (i.e. compatible strings and the respective data) are not
supposed to change at runtime. All functions working with of_device_ids
provided by <linux/of.h> work with const of_device_ids. So mark the
non-const function parameters and structs for OMAP2+ as const, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cleanups for 3.16. Among these are:
- A bunch of misc cleanups for Broadcom platforms, mostly housekeeping
- Enabling Common Clock Framework on the older s3c24xx Samsung chipsets
- Cleanup of the Versatile Express system controller code, moving it to syscon
- Power management cleanups for OMAP platforms
+ a handful of other cleanups across the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=wuX4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC cleanups from Olof Johansson:
"Cleanups for 3.16. Among these are:
- a bunch of misc cleanups for Broadcom platforms, mostly
housekeeping
- enabling Common Clock Framework on the older s3c24xx Samsung
chipsets
- cleanup of the Versatile Express system controller code, moving it
to syscon
- power management cleanups for OMAP platforms
plus a handful of other cleanups across the place"
* tag 'cleanup-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
ARM: kconfig: allow PCI support to be selected with ARCH_MULTIPLATFORM
clk: samsung: fix build error
ARM: vexpress: refine dependencies for new code
clk: samsung: clk-s3c2410-dlck: do not use PNAME macro as it declares __initdata
cpufreq: exynos: Fix the compile error
ARM: S3C24XX: move debug-macro.S into the common space
ARM: S3C24XX: use generic DEBUG_UART_PHY/_VIRT in debug macro
ARM: S3C24XX: trim down debug uart handling
ARM: compressed/head.S: remove s3c24xx special case
ARM: EXYNOS: Remove unnecessary inclusion of cpu.h
ARM: EXYNOS: Migrate Exynos specific macros from plat to mach
ARM: EXYNOS: Remove exynos_subsys registration
ARM: EXYNOS: Remove duplicate lines in Makefile
ARM: EXYNOS: use v7_exit_coherency_flush macro for cache disabling
ARM: OMAP4: PRCM: remove references to cm-regbits-44xx.h from PRCM core files
ARM: OMAP3/4: PRM: add support of late_init call to prm_ll_ops
ARM: OMAP3/OMAP4: PRM: add prm_features flags and add IO wakeup under it
ARM: OMAP3/4: PRM: provide io chain reconfig function through irq setup
ARM: OMAP2+: PRM: remove unnecessary cpu_is_XXX calls from prm_init / exit
ARM: OMAP2+: PRCM: cleanup some header includes
...
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The variable use_gptimer_clksrc is only used by two __init functions,
So we can freely free it after boot.
Signed-off-by: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SyncTimer in AM43x is clocked using the following two sources:
1) An inaccuarte 32k clock (CLK_32KHZ) derived from PER DPLL, causing system
time to go slowly (~10% deviation).
2) external 32KHz RTC clock, which may not always be available on board like
in the case of ePOS EVM
Use gptimer as clocksource instead, as is done in the case of AM335x
(which does not have a SyncTimer). With this, system time keeping works
accurately.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for Samsung
chips. Additionally there are other smaller clock driver changes and
several last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WRJD
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework changes from Mike Turquette:
"The second half of the clock framework pull requeust for 3.14 is
dominated by platform support for Qualcomm's MSM SoCs, DT binding
updates for TI's OMAP-ish processors and additional support for
Samsung chips.
Additionally there are other smaller clock driver changes and several
last minute fixes. This pull request also includes the HiSilicon
support that depends on the already-merged arm-soc pull request"
[ Fix up stupid compile error in the source tree with evil merge - Grumpy Linus ]
* tag 'clk-for-linus-3.14-part2' of git://git.linaro.org/people/mike.turquette/linux: (49 commits)
clk: sort Makefile
clk: sunxi: fix overflow when setting up divided factors
clk: Export more clk-provider functions
dt-bindings: qcom: Fix warning with duplicate dt define
clk: si5351: remove variant from platform_data
clk: samsung: Remove unneeded semicolon
clk: qcom: Fix modular build
ARM: OMAP3: use DT clock init if DT data is available
ARM: AM33xx: remove old clock data and link in new clock init code
ARM: AM43xx: Enable clock init
ARM: OMAP: DRA7: Enable clock init
ARM: OMAP4: remove old clock data and link in new clock init code
ARM: OMAP2+: io: use new clock init API
ARM: OMAP2+: PRM: add support for initializing PRCM clock modules from DT
ARM: OMAP3: hwmod: initialize clkdm from clkdm_name
ARM: OMAP: hwmod: fix an incorrect clk type cast with _get_clkdm
ARM: OMAP2+: clock: use driver API instead of direct memory read/write
ARM: OMAP2+: clock: add support for indexed memmaps
ARM: dts: am43xx clock data
ARM: dts: AM35xx: use DT clock data
...
clk_init is now separated to a common function which gets called for all
SoC:s, which initializes the DT clocks and calls the SoC specific clock init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The 32 bit sched_clock interface now supports 64 bits. Upgrade to
the 64 bit function to allow us to remove the 32 bit registration
interface.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Santosh Shilimkar<santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
A set of fixes for various platforms that weren't considered bad enough
to include in 3.12 (nor -stable). Mostly simple typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=70+h
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC low-priority fixes from Olof Johansson:
"A set of fixes for various platforms that weren't considered bad
enough to include in 3.12 (nor -stable). Mostly simple typo fixes,
etc"
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: irq, AM33XX add missing register check
ARM: OMAP2+: wakeupgen: AM43x adaptation
ARM: OMAP1: Fix a bunch of GPIO related section warnings after initdata got corrected
ARM: dts: fix PL330 MDMA1 address in DT for Universal C210 board
ARM: dts: Work around lack of cpufreq regulator lookup for exynos4210-origen and trats boards
ARM: dts: Fix typo earlyprintk in exynos5440-sd5v1 and ssdk5440 boards
ARM: dts: Correct typo in use of samsung,pin-drv for exynos5250
ARM: rockchip: remove obsolete rockchip,config properties
ARM: rockchip: fix wrong use of non-existent CONFIG_LOCAL_TIMERS
ARM: mach-omap1: Fix omap1510_fpga_init_irq() implicit declarations.
ARM: OMAP1: fix incorrect placement of __initdata tag
ARM: OMAP: remove deprecated IRQF_DISABLED
ARM: OMAP2+: throw the die id into the entropy pool
Otherwise we can get an error with some configs:
arch/arm/mach-omap2/timer.c:73: undefined reference to `omap_smc1'
Signed-off-by: Tony Lindgren <tony@atomide.com>
The realtime counter called master counter, produces the count
used by the private timer peripherals in the MPU_CLUSTER. The
CNTFRQ per cpu register is used to denote the frequency of the counter.
Currently the frequency value is passed from the
DT file, but this is not scalable when we have other non-DT guest
OS. This register must be set to the right value by the
secure rom code. Setting this register helps in propagating the right
frequency value across OSes.
More discussions and the reason for adding this in a non-DT
way can be seen from below.
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg93832.html
So configuring this secure register for all the cpus here.
Cc: Nishanth Menon <nm@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The real time counter also called master counter, is a free-running
counter. It produces the count used by the CPU local timer peripherals
in the MPU cluster. The timer counts at a rate of 6.144 MHz.
The ratio registers are missing for a sys-clk of 20MHZ which is used
by DRA7 socs. So because of this, the counter was getting wrongly
programmed for a sys-clk of 38.4Mhz(default). So adding the ratio
registers for 20MHZ sys-clk.
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since dra7 reuses the function 'omap5_realtime_timer_init' in
arch/arm/mach-omap2/board-generic.c as timer init function, it has to be
built for this SoC as well.
Signed-off-by: Simon Barth <Simon.Pe.Barth@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch proposes to remove the IRQF_DISABLED flag from OMAP code
It's a NOOP since 2.6.35, and will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSKhYmAAoJEIwa5zzehBx322AP/1ONYs8o8f7/Gzq6lZvTN6T3
0pBTApg6Jfioi3lwKvUAEIcsW82YKQ+UZkbW66GQH6+Ri4aZJKZHuz0+JPU67OJ4
LtSLuzVWrymy2VOOUvAnS/SXkOZw/pHhU4cLNHn1dMndhUL1Uqp9/XwuiHEQyFsP
uOkpcBtIu0EWElov0PKKZ5SWBg8JJs2vy5ydiViGelWHCrZvDDZkWzIsDcBQxJLQ
juzT4+JE+KOu7vKmfw78o6iHoCS2TBRAN9YUCajRb8Wl+out1hrTahHnDWaZ5Mce
EskcQNkJROqFbjD4k3ABN4XGTv2VDmrztIwFe0SEQ7Dz/9ypCrBGT69uI9xIqTXr
GwVRIwAUFTpMupK0gy93z1ajV3N0CXV79out9+jQNUQybYE+czp8QOyhmuc1tZx0
8fn9jlBQe9Vy6yrs39gEcE7nUwrayeyQ+6UvqqwsE2pWZabNAnCMSPX5+QIu+T/3
tQ7+jYmfFeserp1sIDOHOnxfhtW9EI6U9d1h/DUCwrsuFdkL9ha4M/vh9Pwgye98
tBdz0T4yE39AJQwwFWRkv1jcQKcGu6WqJanmvS4KRBksGwuLWxy+ewOnkz2ifS25
ZYSyxAryZRBvQRqlOK11rXPfRcbGcY0MG9lkKX96rGcyWEizgE1DdjxXD8HoIleN
R8heV6GX5OzlFLGX2tKK
=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM driver
and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM platform
code for include changes so we took it through our tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1vE4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
The denominator should be load from INCREMENTOR_DENUMERATOR_RELOAD_OFFSET
rather than INCREMENTER_NUMERATOR_OFFSET.
This is more likely a typo, since INCREMENTER_DENUMERATOR_RELOAD[23:17] is
reserved. It seems that it won't make much trouble without this fix, because
the useful [11:0] bits are mask and set the right value. Anyway, reading
from a right address is better choice.
Signed-off-by: Chen Baozi <baozich@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of OMAP5 timer support for clocksource and clockevent is completely
reused across DRA7.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
A recent patch ef3160c (ARM: OMAP2+: Divorce from local timer API,
2013-03-04) broke the omap build when SMP=n because the TWD functions
are only compiled on SMP=y builds. Stub out the TWD calls when the TWD
isn't built in to to keep everything building.
arch/arm/mach-omap2/built-in.o: In function `omap4_local_timer_init':
dss-common.c:(.init.text+0x1d90): undefined reference to `twd_local_timer_register'
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
timer API entirely. Doing so will reduce code in ARM core, reduce the
architecture dependencies of our timer drivers, and simplify the code because
we no longer go through an architecture layer that is essentially a hotplug
notifier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABCAAGBQJRydGwAAoJENidgRMleOc9tMMP/Awy0ETkLHQkXdFdRNLQH7Jd
BpDagzBkpt/U/qsh2Dy5Yhz7Qf/HQg6CwJK/b1apHguSPzNcSov+YS7ArPV+kuDY
9OCF5wkVqPW7BPHlxJ+2QAjayIFUaBR+35kpiU+hv9Gkhs11oK90iAWxEIDUGzA6
5miuOVJeyDEwV8des3NYmVVOKziHLJjX3fjMVnc2gxE6PLmOEUQ9t42bVU1aCfub
pRMUXNuG+aFk8lRExPfs4wWfEKCOHrgJPSE4OPFp3pDJeqhFi5tXTiPBQ22FpNf5
78fEDeguS0QS6f/3rGKSdGu/Yz5Lmcldv4tOkfzvNaZP7zhE18wKJu6bSCrZ/Onn
MnhriYWZh+YgX1V8wTMFMPEV+OR+FJdN4C8PhvNWmMC1Xoq25HtrVQUP5aElgAJs
mLcgTXxLYpvZH3jPxdtMR9IuDc+86qmFerGShWqp/1YaNHwpR8dNZxFyVNfw+FUL
/GoAjk/6MsJlZUchiF7I8yp4jYyMcXcV8Bi4tgIAf5rJO9PZBpuxtyAL9uVHnL13
pwkctMnMQwoP6AE9uYfbdnHCKJxF1hny4tKI5sNxAmK8I6bBkfibIZ3sNRAbSrY7
56kV+tJrrgvgAUDkgdluyS9eFs26iHGPsHK4lmzJzFylWmvWFa8tWpP6G0kCa0wP
A1XCqUOryLeL8enPV+z2
=wZbm
-----END PGP SIGNATURE-----
Merge tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From Stephen Boyd:
Now that we have a generic arch hook for broadcast we can remove the
local timer API entirely. Doing so will reduce code in ARM core, reduce
the architecture dependencies of our timer drivers, and simplify the code
because we no longer go through an architecture layer that is essentially
a hotplug notifier.
* tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: smp: Remove local timer API
clocksource: time-armada-370-xp: Divorce from local timer API
clocksource: time-armada-370-xp: Fix sparse warning
ARM: msm: Divorce msm_timer from local timer API
ARM: PRIMA2: Divorce timer-marco from local timer API
ARM: EXYNOS4: Divorce mct from local timer API
ARM: OMAP2+: Divorce from local timer API
ARM: smp_twd: Divorce smp_twd from local timer API
ARM: smp: Remove duplicate dummy timer implementation
Resolved a large number of conflicts due to __cpuinit cleanups, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real use
(and testing) out of the box on hardware.
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fKfy
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is our first set of fixes from arm-soc for 3.11.
- A handful of build and warning fixes from Arnd
- A collection of OMAP fixes
- defconfig updates to make the default configs more useful for real
use (and testing) out of the box on hardware
And a couple of other small fixes. Some of these have been recently
applied but it's normally how we deal with fixes, with less bake time
in -next needed"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (32 commits)
arm: multi_v7_defconfig: Tweaks for omap and sunxi
arm: multi_v7_defconfig: add i.MX options and NFS root
ARM: omap2: add select of TI_PRIV_EDMA
ARM: exynos: select PM_GENERIC_DOMAINS only when used
ARM: ixp4xx: avoid circular header dependency
ARM: OMAP: omap_common_late_init may be unused
ARM: sti: move DEBUG_STI_UART into alphabetical order
ARM: OMAP: build mach-omap code only if needed
ARM: zynq: use DT_MACHINE_START
ARM: omap5: omap5 has SCU and TWD
ARM: OMAP2+: omap2plus_defconfig: Enable appended DTB support
ARM: OMAP2+: Enable TI_EDMA in omap2plus_defconfig
ARM: OMAP2+: omap2plus_defconfig: enable DRA752 thermal support by default
ARM: OMAP2+: omap2plus_defconfig: enable TI bandgap driver
ARM: OMAP2+: devices: remove duplicated include from devices.c
ARM: OMAP3: igep0020: Set DSS pins in correct mux mode.
ARM: OMAP2+: N900: enable N900-specific drivers even if device tree is enabled
ARM: OMAP2+: Cocci spatch "ptr_ret.spatch"
ARM: OMAP2+: Remove obsolete Makefile line
ARM: OMAP5: Enable Cortex A15 errata 798181
...
