mwait_idle() is a C1-only idle loop intended to be more efficient
than HLT, starting on Pentium-4 HT-enabled processors.
But mwait_idle() has been replaced by the more general
mwait_idle_with_hints(), which handles both C1 and deeper C-states.
ACPI processor_idle and intel_idle use only mwait_idle_with_hints(),
and no longer use mwait_idle().
Here we simplify the x86 native idle code by removing mwait_idle(),
and the "idle=mwait" bootparam used to invoke it.
Since Linux 3.0 there has been a boot-time warning when "idle=mwait"
was invoked saying it would be removed in 2012. This removal
was also noted in the (now removed:-) feature-removal-schedule.txt.
After this change, kernels configured with
(CONFIG_ACPI=n && CONFIG_INTEL_IDLE=n) when run on hardware
that supports MWAIT will simply use HLT. If MWAIT is desired
on those systems, cpuidle and the cpuidle drivers above
can be enabled.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
At present, the value of timeout for freezing is 20s, which is
meaningless in case that one thread is frozen with mutex locked
and another thread is trying to lock the mutex, as this time of
freezing will fail unavoidably.
And if there is no new wakeup event registered, the system will
waste at most 20s for such meaningless trying of freezing.
With this patch, the value of timeout can be configured to smaller
value, so such meaningless trying of freezing will be aborted in
earlier time, and later freezing can be also triggered in earlier
time. And more power will be saved.
In normal case on mobile phone, it costs real little time to freeze
processes. On some platform, it only costs about 20ms to freeze
user space processes and 10ms to freeze kernel freezable threads.
Signed-off-by: Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The Marvell Kirkwood SoCs have simple cpufreq support in hardware. The
CPU can either use the a high speed cpu clock, or the slower DDR
clock. Add a driver to swap between these two clock sources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixed a typo in referenced file name.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation for the DT bindings in exynos G2D driver.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds the PCU SMBus DeviceID for the Intel Avoton SOC.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
OVMF (an implementation of UEFI based on TianoCore used in virtual
environments) now has the ability to boot Linux natively; this is used
for "qemu -kernel" and similar things in a UEFI environment.
Accordingly, assign it a bootloader ID.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
This patch adds new capture board Hawell HW-9004V1. This card has 4 SAA71300 chips. In order to work it is needed to initialize its registers (gpio mask and value). The value of these registers were dumped under Windows using flytest.
Signed-off-by: Vadim Frolov <fralik@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create cmd_dtc_cpp to run the C pre-processor on *.dts file before
passing them to dtc for final compilation. This allows the use of #define
and #include within the .dts file.
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Michal Marek <mmarek@suse.cz>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some matrix keypad drivers can support different numbers of rows and
columns. Add a generic binding for these.
Implementation note:
In order to implement this binding in the kernel, we will need to modify
matrix_keypad_() to look up the number of rows and cols in
the keymap. Perhaps this could be done by passing 0 for these parameters?
Many of the parameters can already be set to NULL. Ick.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Marvell Dove SoC has a thermal sensor. Add a driver using the
thermal framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds support for Kirkwood 88F6282 and 88F6283 thermal sensor.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Support for loading the Renesas R-Car thermal module via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Instead of reimplementing all of the dma_buf functionality in every driver,
create helpers drm_prime_import and drm_prime_export that implement them in
terms of new, lower-level hook functions:
gem_prime_pin: callback when a buffer is created, used to pin buffers into GTT
gem_prime_get_sg_table: convert a drm_gem_object to an sg_table for export
gem_prime_import_sg_table: convert an sg_table into a drm_gem_object
gem_prime_vmap, gem_prime_vunmap: map and unmap an object
These hooks are optional; drivers can opt in by using drm_gem_prime_import and
drm_gem_prime_export as the .gem_prime_import and .gem_prime_export fields of
struct drm_driver.
v2:
- Drop .begin_cpu_access. None of the drivers this code replaces implemented
it. Having it here was a leftover from when I was trying to include i915 in
this rework.
- Use mutex_lock instead of mutex_lock_interruptible, as these three drivers
did. This patch series shouldn't change that behavior.
- Rename helpers to gem_prime_get_sg_table and gem_prime_import_sg_table.
Rename struct sg_table* variables to 'sgt' for clarity.
- Update drm.tmpl for these new hooks.
v3:
- Pass the vaddr down to the driver. This lets drivers that just call vunmap on
the pointer avoid having to store the pointer in their GEM private structures.
- Move documentation into a /** DOC */ comment in drm_prime.c and include it in
drm.tmpl with a !P line. I tried to use !F lines to include documentation of
the individual functions from drmP.h, but the docproc / kernel-doc scripts
barf on that file, so hopefully this is good enough for now.
- apply refcount fix from commit be8a42ae60
("drm/prime: drop reference on imported dma-buf come from gem")
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Dave Airlie <airlied@redhat.com>
videomode helpers for of + devicetree stuff, required for new kms drivers
(not the fbdev maintainer).
* tag 'of_videomode_helper' of git://git.pengutronix.de/git/str/linux:
drm_modes: add of_videomode helpers
drm_modes: add videomode helpers
fbmon: add of_videomode helpers
fbmon: add videomode helpers
video: add of helper for display timings/videomode
video: add display_timing and videomode
viafb: rename display_timing to via_display_timing
This pulls in most of Linus tree up to -rc6, this fixes the worst lockdep
reported issues and re-enables fbcon lockdep.
(not the fbcon maintainer)
* 'fbcon-locking-fixes' of ssh://people.freedesktop.org/~airlied/linux: (529 commits)
Revert "Revert "console: implement lockdep support for console_lock""
fbcon: fix locking harder
fb: Yet another band-aid for fixing lockdep mess
fb: rework locking to fix lock ordering on takeover
leds-ns2.txt is a binding for LEDs, not GPIOs. Move the documentation in
with the rest of the LEDs bindings.
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Update changed platform data information.
Add leds-lp55xx.txt which includes the firmware interface description.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
MAX34460 is a PMBus 12-Channel Voltage Monitor & Sequencer.
MAX34461 is a PMBus 16-Channel Voltage Monitor & Sequencer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the ZL6100 compatible chips support monitoring a separate voltage pin,
VMON (ZL2004) or VDRV (ZL91xx). Report it as in2 / vmon.
The chips support implicit warning limits for VMON/VDRV, as percentage of the
respective critical voltage. Support by reading/writing the critical voltages
and calculating the associated warning voltages.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the TI / Burr-Brown INA209 voltage / current / power
monitor.
Cc: Paul Hays <haysp@magma.net>
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Tested-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for temp1_min_alarm and temp1_max_alarm
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup; dropped platform data and interrupt support]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The LM73 supports four A/D conversion resolutions. The default used by
the existing lm73 driver is the chip's default, 11-bit (0.25 C/LSB).
This patch enables changing of this resolution from userspace via the
update_interval sysfs attribute. Full details on usage are included in
Documentation/hwmon/lm73.
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
[linux@roeck-us.net: cleanup]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Assume that IT8771E and IT8772E are fully compatible with IT8728F.
IT8771E support contributed by Kelly Anderson.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Add support for MAX6581, MAX6602, MAX6622, MAX6636, MAX6689, MAX6693,
MAX6694, MAX6697, MAX6698, and MAX6699 temperature sensors
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
The IMA policy permits specifying rules to enable or disable
measurement/appraisal/audit based on the file system magic number.
If, for example, the policy contains an ext4 measurement rule,
the rule is enabled for all ext4 partitions.
Sometimes it might be necessary to enable measurement/appraisal/audit
only for one partition and disable it for another partition of the
same type. With the existing IMA policy syntax, this can not be done.
This patch provides support for IMA policy rules to specify the file
system by its UUID (eg. fsuuid=397449cd-687d-4145-8698-7fed4a3e0363).
For partitions not being appraised, it might be a good idea to mount
file systems with the 'noexec' option to prevent executing non-verified
binaries.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
The documentation suggested that if the control value is wrong only
ERANGE can be returned. But in some cases (an invalid menu index)
EINVAL can also be returned. Clarify this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The documentation of the error_idx field was incomplete and confusing.
This patch improves it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed the following errors (with exception of the SVG errors):
GEN /home/hans/work/src/v4l/media-git/Documentation/DocBook//v4l2.xml
rm -rf Documentation/DocBook/index.html; echo '<h1>Linux Kernel HTML Documentation</h1>' >> Documentation/DocBook/index.html && echo '<h2>Kernel Version: 3.8.0-rc1</h2>' >> Documentation/DocBook/index.html && cat Documentation/DocBook/media_api.html >> Documentation/DocBook/index.html
/tmp/x.xml:883: element revremark: validity error : Element structname is not declared in revremark list of possible children
/tmp/x.xml:883: element revremark: validity error : Element xref is not declared in revremark list of possible children
/tmp/x.xml:9580: element xref: validity error : Element xref was declared EMPTY this one has content
/tmp/x.xml:13508: element link: validity error : Element link does not carry attribute linkend
/tmp/x.xml:13508: element link: validity error : No declaration for attribute linked of element link
/tmp/x.xml:16986: element imagedata: validity error : Value "SVG" for attribute format of imagedata is not among the enumerated set
/tmp/x.xml:17003: element imagedata: validity error : Value "SVG" for attribute format of imagedata is not among the enumerated set
/tmp/x.xml:17022: element imagedata: validity error : Value "SVG" for attribute format of imagedata is not among the enumerated set
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support to set the emulated temperature method in
thermal zone (sensor). After setting this feature thermal zone may
report this temperature and not the actual temperature. The emulation
implementation may be based on sensor capability through platform
specific handler or pure software emulation if no platform handler defined.
This is useful in debugging different temperature threshold and its
associated cooling action. Critical threshold's cannot be emulated.
Writing 0 on this node should disable emulation.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Intel PowerClamp driver performs synchronized idle injection across
all online CPUs. The goal is to maintain a given package level C-state
ratio.
Compared to other throttling methods already exist in the kernel,
such as ACPI PAD (taking CPUs offline) and clock modulation, this is often
more efficient in terms of performance per watt.
Please refer to Documentation/thermal/intel_powerclamp.txt for more details.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
The struct v4l2_capability card field stores the device name. That name
can be hardcoded in drivers, or be retrieved directly from the device.
The later is very common with USB devices. As several devices already
report names that include non-ASCII characters, update the field
description to use UTF-8.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UMMs
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/dt
From Stephen Warren:
ARM: tegra: device tree updates
Numerous updates to the various Tegra device trees are made:
* Addition of NVIDIA Beaver (Tegra30) and Toradex Colibri T20 and Iris
carrier boards.
* Enablement of the HDMI connector on most boards.
* Enablement of the keyboard controller on a few boards.
* Addition of the AC'97 controller to Tegra20.
* Addition of a GPIO poweroff node for TrimSlice.
* Changes to support the new "high speed UART" (DMA-capable) driver for
Tegra serial ports, and enablement for Cardhu's UART C.
* A few cleanups, such as compatible flag fixes, node renames, node
ordering fixes, commonizing properties into SoC .dtsi files, etc..
This pull request is based on (most of) the previous pull request with
tag tegra-for-3.9-soc-t114.
* tag 'tegra-for-3.9-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (22 commits)
ARM: dt: tegra30: Rename "smmu" to "iommu"
ARM: dt: tegra20: Rename "gart" to "iommu"
ARM: tegra: move serial clock-frequency attr into the Tegra30 dtsi
ARM: tegra: Add Toradex Iris carrier board DT with T20 512MB COM
ARM: tegra: Add Colibri T20 512MB COM device tree
ARM: tegra: move serial clock-frequency attr into the Tegra20 dtsi
ARM: tegra: harmony: enable keyboard in DT
ARM: tegra: whistler: enable keyboard in DT
ARM: tegra: cardhu: register UARTC
ARM: tegra: seaboard: enable keyboard in DT
ARM: tegra: add DT entry for KBC controller
ARM: tegra: swap cache-/interrupt-ctrlr nodes in DT
ASoC: tegra: add ac97 host controller to device tree
ARM: DT: tegra: Add Tegra30 Beaver board support
ARM: DT: tegra: Add board level compatible properties
ARM: tegra: paz00: enable HDMI port
ARM: tegra: ventana: enable HDMI port
ARM: tegra: seaboard: enable HDMI port
ARM: tegra: trimslice: add gpio-poweroff node to DT
ARM: DT: tegra: Unify the description of Tegra20 boards
...
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8pTe
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: USB driver cleanup
The Tegra USB driver has a number of issues:
1) The PHY driver isn't a true platform device, and doesn't implement
the standard USB PHY API.
2) struct device instance numbers were used to make decisions in the
driver, rather than being parameterized by DT or platform data.
This pull request solves issue (2), and lays the groundwork for solving
issue (1). The work on issue (1) involved introducing new DT nodes for
the USB PHYs, which in turn interacted with the Tegra common clock
framework changes, due to the move of clock lookups into device tree.
Hence, these USB driver changes are taken through the Tegra tree with
acks from USB maintainers.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-soc-ccf.
* tag 'tegra-for-3.9-soc-usb' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
usb: host: tegra: make use of PHY pointer of HCD
ARM: tegra: Add reset GPIO information to PHY DT node
usb: host: tegra: don't touch EMC clock
usb: add APIs to access host registers from Tegra PHY
USB: PHY: tegra: Get rid of instance number to differentiate PHY type
USB: PHY: tegra: get rid of instance number to differentiate legacy controller
ARM: tegra: add clocks properties to USB PHY nodes
ARM: tegra: add DT nodes for Tegra USB PHY
usb: phy: remove unused APIs from Tegra PHY.
usb: host: tegra: Resetting PORT0 based on information received via DT.
ARM: tegra: Add new DT property to USB node.
usb: phy: use kzalloc to allocate struct tegra_usb_phy
ARM: tegra: remove USB address related macros from iomap.h
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9hz
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
TCP Appropriate Byte Count was added by me, but later disabled.
There is no point in maintaining it since it is a potential source
of bugs and Linux already implements other better window protection
heuristics.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a helper function that allows to modify range,
i.e. minimum, maximum, step and default value of a v4l2 control,
after the control has been created and initialized. This is helpful
in situations when range of a control depends on user configurable
parameters, e.g. camera sensor absolute exposure time depending on
an output image resolution and frame rate.
v4l2_ctrl_modify_range() function allows to modify range of an
INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls.
Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds the capability to retrieve setup data from the device tree
node. The usage of platform data is still available.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The definitions of hw constraint functions are wrongly placed, and the
description about the function is also wrong.
hw_rule_channels_by_format actually refines the channels depending on
the format, not vice versa.
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We recently refactored the driver source, this patch will take care of
updating copyright date and adding it to newly added files.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Xiao pointed out, there are a few problems with it:
- kvm_arch_commit_memory_region() write protects the memory slot only
for GET_DIRTY_LOG when modifying the flags.
- FNAME(sync_page) uses the old spte value to set a new one without
checking KVM_MEM_READONLY flag.
Since we flush all shadow pages when creating a new slot, the simplest
fix is to disallow such problematic flag changes: this is safe because
no one is doing such things.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Pull x86 fixes from Ingo Molnar:
"Three small fixlets"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel/cacheinfo: Shut up annoying warning
x86, doc: Boot protocol 2.12 is in 3.8
x86-64: Replace left over sti/cli in ia32 audit exit code
Pull two small RCU fixlets from Ingo Molnar.
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rcu: Make rcu_nocb_poll an early_param instead of module_param
rcu: Prevent soft-lockup complaints about no-CBs CPUs
Convert MicBias widgets to supply widget.
On tlv320aic3x, Mic bias power on/off shares the same register bits
with output mic bias voltage. So, when power on mic bias, we need
reclaim it to voltage value.
Provide a new platform data so that the micbias voltage can be sent
according to board requirement. Now since tlv320aic3x codec driver
is DT aware, update dt files and functions to handle this new
"micbias-vg" platform data.
Because of sharing of bits, when enabling the micbias, voltage also
needs to be updated. So use SND_SOC_DAPM_POST_PMU & SND_SOC_DAPM_PRE_PMD
macro to create an event to handle this.
Since micbias is converted to supply widget, updated machine drivers as
well.
This change is runtime tested on da850-evm with audio loopback
(arecord|aplay) for confirmation.
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This new property defines the era of the particular SEC version.
The compatible property in device tree "crypto" node has been updated
not to contain SEC era numbers.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This device tree support is added for PMIC block of S5m8767 multi
function driver. The usage detail is added in the device tree
documentation section. This change is tested on exynos5250 based
arndale platform by regulator voltage set/get API's.
Reviewed-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As part of removing generalized dependency, replace <xx> literal fields
in DT compatible field with <52> for am335x platforms.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently cfi_cmdset_0002.c does not support PPB locking of sectors. This
patch adds support for this locking/unlocking mechanism. It is needed on
some platforms, since newer U-Boot versions do support this PPB locking
and protect for example their environment sector(s) this way.
This PPB locking/unlocking will be enabled for all devices supported by
cfi_cmdset_0002 reporting 8 in the CFI word 0x49 (Sector Protect/Unprotect
scheme).
Please note that PPB locking does support sector-by-sector locking. But
the whole chip can only be unlocked together. So unlocking one sector
will automatically unlock all sectors of this device. Because of this
chip limitation, the PPB unlocking function saves the current locking
status of all sectors before unlocking the whole device. After unlocking
the saved locking status is re-configured. This way only the addressed
sectors will be unlocked.
To selectively enable this advanced sector protection mechanism, the
device-tree property "use-advanced-sector-protection" has been created.
To enable support for this locking this property needs to be present in the
flash DT node. E.g.:
nor_flash@0,0 {
compatible = "amd,s29gl256n", "cfi-flash";
bank-width = <2>;
use-advanced-sector-protection;
...
Tested with Spansion S29GL512S10THI and Micron JS28F512M29EWx flash
devices.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ELM hardware module can be used to speedup BCH 4/8/16 ECC scheme
error correction.
For now only 4 & 8 bit support is added
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The DT binding for the pwm-leds devices are similar to the gpio-leds type.
LEDs are represented as sub-nodes of the pwm-leds device.
The code for handling the DT boot is based on the code found in the
leds-gpio driver and adapted to use PWMs instead of GPIOs.
To avoid having custom cleanup code in case of DT boot the newly created
devm_of_pwm_get() API is used to get the correct PWM instance.
For usage see:
Documentation/devicetree/bindings/leds/leds-pwm.txt
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Documentation related to cpus and related_cpus is confusing and not very clear.
Over that CPUFreq core has seen much changes recently. Lets update documentation
and comments for cpus and related_cpus.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In case ELM module available, omap2 NAND driver can opt for hardware
correction method for bit flip errors in NAND flash with BCH. Hence the
detection of ELM module is done through devicetree population of elm_id.
This patch update device tree documentation for gpmc-nand for elm-id
data population.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds device tree bindings for OMAP OneNAND devices.
Tested on an OMAP3 3430 IGEPv2 board.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The original suggestion to delete wanrouter started earlier
with the mainline commit f0d1b3c2bc
("net/wanrouter: Deprecate and schedule for removal") in May 2012.
More importantly, Dan Carpenter found[1] that the driver had a
fundamental breakage introduced back in 2008, with commit
7be6065b39 ("netdevice wanrouter: Convert directly reference of
netdev->priv"). So we know with certainty that the code hasn't been
used by anyone willing to at least take the effort to send an e-mail
report of breakage for at least 4 years.
This commit does a decouple of the wanrouter subsystem, by going
after the Makefile/Kconfig and similar files, so that these mainline
files that we are keeping do not have the big wanrouter file/driver
deletion commit tied into their history.
Once this commit is in place, we then can remove the obsolete cyclomx
drivers and similar that have a dependency on CONFIG_WAN_ROUTER_DRIVERS.
[1] http://www.spinics.net/lists/netdev/msg218670.html
Originally-by: Joe Perches <joe@perches.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
PullHID fixes from Jiri Kosina:
- fix i2c-hid and hidraw interaction, by Benjamin Tissoires
- a quirk to make a particular device (Formosa IR receiver) work
properly, by Nicholas Santos
* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: fix i2c_hid_output_raw_report
HID: usbhid: quirk for Formosa IR receiver
HID: remove x bit from sensor doc
Document PCIe bus MPS parameters pcie_bus_tune_off, pcie_bus_safe,
pcie_bus_peer2peer, pcie_bus_perf.
These parameters were introduced by Jon Mason <jdmason@kudzu.us> at commit
5f39e6705 and commit b03e7495a8.
[bhelgaas: mention hot-add for pcie_bus_peer2peer]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patchset addes two new sets of files to sysfs for POWER architecture.
- perf event config format in /sys/devices/cpu/format/event
- generic and POWER-specific perf events in /sys/devices/cpu/events/
The format of the first file is already documented in:
sysfs-bus-event_source-devices-format
Document the format of the second set of files '/sys/devices/cpu/events/*'
which would also become part of the ABI.
Changelog[v4]:
[Jiri Olsa]: Mention that multiple event= like terms can be specified
in the 'events' file.
[Jiri Olsa]: Remove the documentation for the 'config format' file
as it is already documented in 'Documentation/ABI/testing/'.
[Jiri Olsa]: Move ABI documentation from 'stable/' to 'testing/'
Changelog[v3]:
[Greg KH] Include ABI documentation.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062645.GG13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Make the generic perf events in POWER7 available via sysfs.
$ ls /sys/bus/event_source/devices/cpu/events
branch-instructions
branch-misses
cache-misses
cache-references
cpu-cycles
instructions
stalled-cycles-backend
stalled-cycles-frontend
$ cat /sys/bus/event_source/devices/cpu/events/cache-misses
event=0x400f0
This patch is based on commits that implement this functionality on x86.
Eg:
commit a47473939d
Author: Jiri Olsa <jolsa@redhat.com>
Date: Wed Oct 10 14:53:11 2012 +0200
perf/x86: Make hardware event translations available in sysfs
Changelog:[v2]
[Jiri Osla] Drop EVENT_ID() macro since it is only used once.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Anton Blanchard <anton@au1.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: linuxppc-dev@ozlabs.org
Link: http://lkml.kernel.org/r/20130123062454.GD13720@us.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently the documentation for the arch_timer devicetree binding only
lists "arm,armv7-timer".
Add "arm,armv8-timer" to the list of compatible strings.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch to the SRW-S1 driver adds the ability to control all
LEDs simultaneously as testing showed that it was slow (noticably!!)
when seting or clearing all the LEDs in turn.
It adds a 'RPMALL' LED, whose behavoir is asserted to all the LEDs in
the bar graph, individual LEDs can subsequently be turned on/off
individually.
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch to the SRW-S1 driver adds support for the LED RPM
meter on the front of the device. The LEDs are controlled via
/sys/class/leds interface, with an individual control for each
of the 15 LEDs.
Signed-off-by: Simon Wood <simon@mungewell.org>
Tested-by: John Murphy <rosegardener@freeode.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
some of anatop's regulators(cpu, vddpu and vddsoc) have
register settings about LDO's step time, which will impact
the LDO ramp up speed, need to use set_voltage_time_sel
interface to add necessary delay everytime LDOs' voltage
is increased.
offset 0x170:
bit [24-25]: cpu
bit [26-27]: vddpu
bit [28-29]: vddsoc
field definition:
0'b00: 64 cycles of 24M clock;
0'b01: 128 cycles of 24M clock;
0'b02: 256 cycles of 24M clock;
0'b03: 512 cycles of 24M clock;
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
This patch adds snapshot description in ftrace documentation.
This description includes what the snapshot is and how to use it.
Link: http://lkml.kernel.org/r/20121226025309.3252.150.stgit@liselsia
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Hiraku Toyooka <hiraku.toyooka.gu@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Introduce struct acpi_scan_handler for representing objects that
will do configuration tasks depending on ACPI device nodes'
hardware IDs (HIDs).
Currently, those tasks are done either directly by the ACPI namespace
scanning code or by ACPI device drivers designed specifically for
this purpose. None of the above is desirable, however, because
doing that directly in the namespace scanning code makes that code
overly complicated and difficult to follow and doing that in
"special" device drivers leads to a great deal of confusion about
their role and to confusing interactions with the driver core (for
example, sysfs directories are created for those drivers, but they
are completely unnecessary and only increase the kernel's memory
footprint in vain).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
During kdump kernel's booting stage, it need to find low ram for
swiotlb buffer when system does not support intel iommu/dmar remapping.
kexed-tools is appending memmap=exactmap and range from /proc/iomem
with "Crash kernel", and that range is above 4G for 64bit after boot
protocol 2.12.
We need to add another range in /proc/iomem like "Crash kernel low",
so kexec-tools could find that info and append to kdump kernel
command line.
Try to reserve some under 4G if the normal "Crash kernel" is above 4G.
User could specify the size with crashkernel_low=XX[KMG].
-v2: fix warning that is found by Fengguang's test robot.
-v3: move out get_mem_size change to another patch, to solve compiling
warning that is found by Borislav Petkov <bp@alien8.de>
-v4: user must specify crashkernel_low if system does not support
intel or amd iommu.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-31-git-send-email-yinghai@kernel.org
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Now 64bit entry is fixed on 0x200, can not be changed anymore.
Update the comments to reflect that.
Also put info about it in boot.txt
-v2: fix some grammar error
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-27-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set converts the Nomadik (mach-nomadik) to
Device Tree and delete the old board files, paving the
road for single zImage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Ip5x
-----END PGP SIGNATURE-----
Merge tag 'nmk-dt-on-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
From Linus Walleij:
Nomadik Device Tree conversion rebased on ARM SoC cleanup branch
This patch set converts the Nomadik (mach-nomadik) to
Device Tree and delete the old board files, paving the
road for single zImage.
* tag 'nmk-dt-on-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: get rid of <mach/hardware.h>
ARM: nomadik: delete old board files
ARM: nomadik: add I2C devices to the device tree
ARM: nomadik: migrate MMC/SD card support to device tree
ARM: nomadik: convert SMSC91x ethernet to device tree
ARM: nomadik: move GPIO and pinctrl to device tree
ARM: nomadik: add FSMC NAND
ARM: nomadik: move remaining PrimeCells to device tree
ARM: nomadik: move pin maps to cpu file
ARM: nomadik: initial devicetree support
ARM: nomadik: move last custom calls to pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the basic device tree based lookup.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for device based discovery.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
dmraid assess redundancy and replacements slightly inaccurately which
could lead to some degraded arrays failing to assemble.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIVAwUAUQb0OTnsnt1WYoG5AQJ4qg/8DIs0eWaJWF5lqF8qJBeMQrUDkqe7glqe
ezwVlO48uxVzJUxCMd1aZdxjTI/AIvqZ1U5DBC62SlB/RqWlrwIQIIok5odWfnG4
eAII5hUnktWqL4Ksqz4mgdI+WWwSc3JR7verqS4wOvcsN4qU5t8vL6dj2b0cNYCQ
I7B+fkMZE1KE4Y2DOf8dEO9gbNIO1ZllZapLRolrsGOr8Ggo1prEoMxBYF5HZNoE
J1As2N6NA7/kadtsfkCSs+f//5t1uMZluMjEUe4lDmgeqzqz/93kFmJ2OfSdqO4J
wuuTHbCL+NSjjAZuByluSO98O0h87xXGVMv/c7gadVQtOn6I1DA2i4wTaiHOzr4K
cdALvbteVCAPYLMA+s8ee6YYbB5pnlblT8FShG+3O6ae1KmbqKex1LlZLpwEoS8y
VxI1WCSQbBr/ejAnhxLFQPo5OAcoeHomlZHKPtCBSbwQ0f0pOHHPYlZyX2PtX6hF
U9bmtMq0XZulDORdLmIsEEpwzRKQ+b89+RrYXM7AhkJTxRP59RVwqFHy9SybcFBS
S5XFKqpCE+ioBvLp9HK189xMe0Nel2g7KWd34v5LcvQ21rzATezAh5TsWIzN3oV8
9/phd6nZa0hhcELykOTmK5b6+ks2tBfEN2FuyKfSq4Z2nz46rfD4wYVTY2+Qjh+D
hmUDBgguejo=
=bJyL
-----END PGP SIGNATURE-----
Merge tag 'md-3.8-fixes' of git://neil.brown.name/md
Pull dmraid fix from NeilBrown:
"Just one fix for md in 3.8
dmraid assess redundancy and replacements slightly inaccurately which
could lead to some degraded arrays failing to assemble."
* tag 'md-3.8-fixes' of git://neil.brown.name/md:
DM-RAID: Fix RAID10's check for sufficient redundancy
Fix the incorrect compatible property value of pinctrl for EXYNOS4 SoCs.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This moves over the MMC/SD card support to the device tree probe
path. The special GPIO to bias the card detect line is kept,
but the pin property is moved to the device tree as part of
the MMC/SD card node.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the SMSC91x ethernet controller to use device
tree. The existing solution from the board file, to request the
GPIO triggering the ethernet IRQ from the board file is kept
for the time being, but the GPIO number assignment is moved
over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the FSMC NAND driver and flash partitions to the Nomadik
device tree.
The only compatible string accepted by this driver is currently
"st,spear600-fsmc-nand" which is inappropriate for this system, so
this patch adds the compatible value "stericsson,fsmc-nand" as
well.
Cc: linux-mtd@vger.kernel.org
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support basic device tree boot on the Nomadik. Implement the
support in the cpu file with the intent of deleting the board
files later. At this stage IRQ controllers, system timer,
l2x0 cache, UARTs and thus console boot is fully functional.
Patch out the code adding devices by initcalls for now so
as not to disturb the boot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As reset GPIO information is PHY specific detail, adding
it to PHY DT node.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds the device tree for the Toradex Iris carrier board used
together with a Colibri T20 512MB COM.
The Iris has the following features, in brackets the current status:
- DVI and VGA output through DVI-I connector (DVI-D enabled and tested)
- LVDS output
- 1 USB host port (enabled and tested)
- 1 USB OTG port (enabled)
- 100 MBit Ethernet (enabled and tested)
- 5 UART ports (2 on 10way headers enabled and tested)
- 1 MicroSD Slot (enabled and tested)
- Audio connectors (enabled, only HP out and Line-in tested)
- i2c RTC
- GPIO connector (enabled, only sparsely tested)
- external i2c bus
- 4 PWM out
- analog in
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This adds the device tree include file for the Toradex Colibri T20
Computer on Module (COM). It's only valid for the 512MB RAM version of
the module, as the 256MB version needs different EMC tables and flash
configuration. To make this clear the suffix -512 was added to the board
compatible string.
The Colibri T20 uses a Tegra20 SoC and has onboard USB Ethernet and AC97
sound.
Still some things like onboard NAND support missing, but should be a
good base for further development.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds support for Tegra30 Beaver board in upstream kernel.
Beaver board is a Tegra30 SoC based development board, it has
following features:
- T30 or T33 SoC (Qual core ARM Cortex A9)
- 2 GB DDR3L
- 16 GB EMMC
- 1 SD slot
- 1 USB Standart A port and 1 USB micro AB port
- PCI-E Gig Ethernet
- Audio input/output
- SATA port
- HDMI output
- UART and JTAG
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The compatible properties of Tegra SoC based boards or machines need
to be documented. This patch adds these board levle compatible
properties into device tree binding document.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add DT nodes for Tegra USB PHY along with related documentation.
Also added a phandle property to controller DT node, for referring
to connected PHY instance.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
As Tegra USB host driver is using instance number for resetting
PORT0 twice, adding a new DT property for handling this.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The device tree binding models Tegra30 CAR (Clock And Reset)
as a single monolithic clock provider.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: fixed typo in binding doc]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra20 CAR (Clock And Reset) Controller controls most aspects of
most clocks within Tegra20. The device tree binding models this as a
single monolithic clock provider, which exports many clocks. This reduces
the number of nodes needed in device tree to represent these clocks.
This binding is only useful for Tegra20; the set of clocks that exists on
Tegra30 is sufficiently different to merit its own binding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
[pgaikwad: Added mux clk ids and sorted CAR node]
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Mostly clock related updates, most notably the conversion of
i.MX31 to a DT based lookup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bWtE
-----END PGP SIGNATURE-----
Merge tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6 into next/soc
From Sascha Hauer:
ARM i.MX SoC updates for next
Mostly clock related updates, most notably the conversion of
i.MX31 to a DT based lookup.
* tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: clk-imx35: Fix build warnings with W=1
ARM: imx27: add a clock gate to activate SPLL clock
ARM: mx31: Replace clk_register_clkdev with clock DT lookup
ARM: clk-imx31: Add dummy clock
ARM: Let CONFIG_MACH_IMX31_DT be built by default
Signed-off-by: Olof Johansson <olof@lixom.net>
From Barry Song, this adds support for a new SoC from CSR; marco. It's
SMP, uses GIC instead of VIC and in general needs a bit of rework of
the platform code for setup, which this branch contains.
* 'marco-timer-cleanup-rebase' of git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel:
ARM: PRIMA2: provide two DEBUG_LL ports for prima2 and marco
ARM: PRIMA2: add new SiRFmarco SMP SoC infrastructures
ARM: PRIMA2: irq: make prima2 irq can work even we enable GIC for Marco
ARM: PRIMA2: rtciobg: it is also compatible with marco
ARM: PRIMA2: rstc: enable the support for Marco
ARM: PRIMA2: mv timer to timer-prima2 as we will add timer-marco
ARM: PRIMA2: initialize l2x0 according to mach from DT
ARM: PRIMA2: enable AUTO_ZRELADDR for SIRF in Kconfig
ARM: PRIMA2: add CSR SiRFmarco device tree .dts
Signed-off-by: Olof Johansson <olof@lixom.net>
i2c_smbus_process_call has no users in the kernel, so this can be
removed. Documentation for the same has been updated accordingly.
Fixes following sparse warning.
drivers/i2c/i2c-core.c:1871:5: warning: symbol 'i2c_smbus_process_call'
was not declared. Should it be static?
[wsa: updated the documentation]
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Define the 2.12 bzImage boot protocol: add xloadflags and additional
fields to allow the command line, initramfs and struct boot_params to
live above the 4 GiB mark.
The xloadflags now communicates if this is a 64-bit kernel with the
legacy 64-bit entry point and which of the EFI handover entry points
are supported.
Avoid adding new read flags to loadflags because of claimed
bootloaders testing the whole byte for == 1 to determine bzImageness
at least until the issue can be researched further.
This is based on patches by Yinghai Lu and David Woodhouse.
Originally-by: Yinghai Lu <yinghai@kernel.org>
Originally-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1359058816-7615-26-git-send-email-yinghai@kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: Gokul Caushik <caushik1@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Joe Millenbach <jmillenbach@gmail.com>
In the help text describing user namespaces recommend use of memory
control groups. In many cases memory control groups are the only
mechanism there is to limit how much memory a user who can create
user namespaces can use.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Pablo Neira Ayuso says:
====================
This batch contains netfilter updates for you net-next tree, they are:
* The new connlabel extension for x_tables, that allows us to attach
labels to each conntrack flow. The kernel implementation uses a
bitmask and there's a file in user-space that maps the bits with the
corresponding string for each existing label. By now, you can attach
up to 128 overlapping labels. From Florian Westphal.
* A new round of improvements for the netns support for conntrack.
Gao feng has moved many of the initialization code of each module
of the netns init path. He also made several code refactoring, that
code looks cleaner to me now.
* Added documentation for all possible tweaks for nf_conntrack via
sysctl, from Jiri Pirko.
* Cisco 7941/7945 IP phone support for our SIP conntrack helper,
from Kevin Cernekee.
* Missing header file in the snmp helper, from Stephen Hemminger.
* Finally, a couple of fixes to resolve minor issues with these
changes, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree based initialization support for
TI's tps6507x regulators.
Add device tree binding document for TI's tps6507x
using datasheet:
http://www.ti.com/lit/ds/symlink/tps65070.pdf
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch implements support for sampling of a touchscreen into
the MXS LRADC driver. The LRADC block allows configuring some of
it's channels into special mode where they either output the drive
voltage or sample it, allowing it to operate a 4-wire or 5-wire
resistive touchscreen.
In case the touchscreen mode is enabled, the LRADC slot #7 is
reserved for touchscreen only, therefore it is not possible to
sample 8 LRADC channels at time, but only 7 channels.
The touchscreen controller is configured such that the PENDOWN event
disables touchscreen interrupts and triggers execution of worker
thread, which then polls the touchscreen controller for X, Y and
Pressure values. This reduces the overhead of interrupt-driven
operation. Upon the PENUP event, the worker thread re-enables the
PENDOWN detection interrupt and exits.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
SENSORS_LIMIT and clamp_val have the same functionality, so retire SENSORS_LIMIT
as it is no longer needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
This boolean function simply returns whether or not the runtime
status of the device is 'active'. The typical scenario is driver
calls pm_runtime_get firstly, then check pm_runtime_active in
atomic environment.
Also add entry to Documentation/power/runtime.txt
Signed-off-by: Yanmin Zhang <yanmin.zhang@intel.com>
Signed-off-by: ShuoX Liu <shuox.liu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The text in Documentation said it would be removed in 2.6.41;
the text in the Kconfig said removal in the 3.1 release. Either
way you look at it, we are well past both, so push it off a cliff.
Note that the POWER_CSTATE and the POWER_PSTATE are part of the
legacy tracing API. Remove all tracepoints which use these flags.
As can be seen from context, most already have a trace entry via
trace_cpu_idle anyways.
Also, the cpufreq/cpufreq.c PSTATE one is actually unpaired, as
compared to the CSTATE ones which all have a clear start/stop.
As part of this, the trace_power_frequency also becomes orphaned,
so it too is deleted.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since ACPI power resources are going to be used more extensively on
new hardware platforms, it is necessary to allow user space (powertop
in particular) to look at the lists of power resources corresponding
to different power states of devices for diagnostics and control
purposes.
For this reason, for each power state of an ACPI device node using
power resources create a special attribute group under the device
node's directory in sysfs containing links to sysfs directories
representing the power resources in that list. The names of the
new attribute groups are "power_resources_<state>", where <state>
is the state name i.e. "D0", "D1", "D2", or "D3hot".
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Technologic Systems TS-5500 is an x86-based (AMD Elan SC520)
single board computer. This driver registers most of its devices
and exposes sysfs attributes for information such as jumpers'
state or presence of some of its options.
This driver currently registers the TS-5500 platform, its
on-board LED, 2 pin blocks (GPIO) and its analog/digital
converter. It can be extended to support other Technologic
Systems products, such as the TS-5600.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Savoir-faire Linux Inc. <kernel@savoirfairelinux.com>
Link: http://lkml.kernel.org/r/1357334294-12760-1-git-send-email-vivien.didelot@savoirfairelinux.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c796
-----END PGP SIGNATURE-----
Merge tag 'xceiv-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: xceiv: patches for v3.9 merge window
Two new PHY drivers coming here: one for Samsung,
one for OMAP. Both architectures are adding USB3
support to mainline kernel.
The PHY layer now allows us to have mulitple PHYs
of the same type, which is necessary for platforms
which provide more than one USB peripheral port.
There's also a few cleanups here: removal of __dev*
annotations, conversion of a cast to to_delayed_work(),
and mxs-phy learns about ->set_suspend.
Added dt support for dwc3 core and update the documentation with
device tree binding information. Getting a PHY is now done using
devm_usb_get_phy_by_phandle() for dt boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added a driver for usb3 phy that handles the interaction between usb phy
device and dwc3 controller.
This also includes device tree support for usb3 phy driver and
the documentation with device tree binding information is updated.
Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Start using the control module driver for powering on the PHY and for
writing to the mailbox instead of writing to the control module
registers on their own.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added a new driver for the usb part of control module. This has an API
to power on the USB2 phy and an API to write to the mailbox depending on
whether MUSB has to act in host mode or in device mode.
Writing to control module registers for doing the above task which was
previously done in omap glue and in omap-usb2 phy will be removed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Added device tree support for usb3503 driver and add new document with device tree binding information.
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
Here's a long-pending fixes pull request for arm-soc (I didn't send one
in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted to
multiplatform on i.MX, which was causing build failures when included
- Device tree updates for at91 dealing mostly with their new
pinctrl setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YDHs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
The new function pci_enable_msi_block_auto() tries to allocate
maximum possible number of MSIs up to the number the device
supports. It generalizes a pattern when pci_enable_msi_block()
is contiguously called until it succeeds or fails.
Opposite to pci_enable_msi_block() which takes the number of
MSIs to allocate as a input parameter,
pci_enable_msi_block_auto() could be used by device drivers to
obtain the number of assigned MSIs and the number of MSIs the
device supports.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/c3de2419df94a0f95ca1a6f755afc421486455e6.1353324359.git.agordeev@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since ACPI power resources are going to be used more extensively on
new hardware platforms, it becomes necessary for user space (powertop
in particular) to observe some properties of those resources for
diagnostics purposes.
For this reason, expose the current status of each ACPI power
resource to user space via sysfs by adding a new resource_in_use
attribute to the sysfs directory representing the given power
resource.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make it possible to retrieve the current power state of a device with
ACPI power management from user space via sysfs by adding two new
attributes, power_state and real_power_state, to the sysfs directory
associated with the struct acpi_device object representing the
device's ACPI node.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for reading display timings from DT into a struct
display_timings. The of_display_timing implementation supports multiple
subnodes. All children are read into an array, that can be queried.
If no native mode is specified, the first subnode will be used.
For cases where the graphics driver knows there can be only one
mode description or where the driver only supports one mode, a helper
function of_get_videomode is added, that gets a struct videomode from DT.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Afzal Mohammed <Afzal@ti.com>
Tested-by: Rob Clark <robclark@gmail.com>
Tested-by: Leela Krishna Amudala <leelakrishna.a@gmail.com>
Before attempting to activate a RAID array, it is checked for sufficient
redundancy. That is, we make sure that there are not too many failed
devices - or devices specified for rebuild - to undermine our ability to
activate the array. The current code performs this check twice - once to
ensure there were not too many devices specified for rebuild by the user
('validate_rebuild_devices') and again after possibly experiencing a failure
to read the superblock ('analyse_superblocks'). Neither of these checks are
sufficient. The first check is done properly but with insufficient
information about the possible failure state of the devices to make a good
determination if the array can be activated. The second check is simply
done wrong in the case of RAID10 because it doesn't account for the
independence of the stripes (i.e. mirror sets). The solution is to use the
properly written check ('validate_rebuild_devices'), but perform the check
after the superblocks have been read and we know which devices have failed.
This gives us one check instead of two and performs it in a location where
it can be done right.
Only RAID10 was affected and it was affected in the following ways:
- the code did not properly catch the condition where a user specified
a device for rebuild that already had a failed device in the same mirror
set. (This condition would, however, be caught at a deeper level in MD.)
- the code triggers a false positive and denies activation when devices in
independent mirror sets have failed - counting the failures as though they
were all in the same set.
The most likely place this error was introduced (or this patch should have
been included) is in commit 4ec1e369 - first introduced in v3.7-rc1.
Consequently this fix should also go in v3.7.y, however there is a
small conflict on the .version in raid_target, so I'll submit a
separate patch to -stable.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The DVBv3 statistics parameters are limited on several ways:
- It doesn't provide any way to indicate the used measure,
so userspace need to guess how to calculate/use it;
- Only a limited set of stats are supported;
- Can't be called in a way to require them to be filled
all at once (atomic reads from the hardware), with may
cause troubles on interpreting them on userspace;
- On some OFDM delivery systems, the carriers can be
independently modulated, having different properties.
Currently, there's no way to report per-layer stats.
To address the above issues, adding a new DVBv5-based stats API.
While here, correct inner code nomenclature on a few places.
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement the PSCI specification (ARM DEN 0022A) to control
virtual CPUs being "powered" on or off.
PSCI/KVM is detected using the KVM_CAP_ARM_PSCI capability.
A virtual CPU can now be initialized in a "powered off" state,
using the KVM_ARM_VCPU_POWER_OFF feature flag.
The guest can use either SMC or HVC to execute a PSCI function.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
We use space #18 for floating point regs.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
The Cache Size Selection Register (CSSELR) selects the current Cache
Size ID Register (CCSIDR). You write which cache you are interested
in to CSSELR, and read the information out of CCSIDR.
Which cache numbers are valid is known by reading the Cache Level ID
Register (CLIDR).
To export this state to userspace, we add a KVM_REG_ARM_DEMUX
numberspace (17), which uses 8 bits to represent which register is
being demultiplexed (0 for CCSIDR), and the lower 8 bits to represent
this demultiplexing (in our case, the CSSELR value, which is 4 bits).
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
The following three ioctls are implemented:
- KVM_GET_REG_LIST
- KVM_GET_ONE_REG
- KVM_SET_ONE_REG
Now we have a table for all the cp15 registers, we can drive a generic
API.
The register IDs carry the following encoding:
ARM registers are mapped using the lower 32 bits. The upper 16 of that
is the register group type, or coprocessor number:
ARM 32-bit CP15 registers have the following id bit patterns:
0x4002 0000 000F <zero:1> <crn:4> <crm:4> <opc1:4> <opc2:3>
ARM 64-bit CP15 registers have the following id bit patterns:
0x4003 0000 000F <zero:1> <zero:4> <crm:4> <opc1:4> <zero:3>
For futureproofing, we need to tell QEMU about the CP15 registers the
host lets the guest access.
It will need this information to restore a current guest on a future
CPU or perhaps a future KVM which allow some of these to be changed.
We use a separate table for these, as they're only for the userspace API.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
All interrupt injection is now based on the VM ioctl KVM_IRQ_LINE. This
works semantically well for the GIC as we in fact raise/lower a line on
a machine component (the gic). The IOCTL uses the follwing struct.
struct kvm_irq_level {
union {
__u32 irq; /* GSI */
__s32 status; /* not used for KVM_IRQ_LEVEL */
};
__u32 level; /* 0 or 1 */
};
ARM can signal an interrupt either at the CPU level, or at the in-kernel irqchip
(GIC), and for in-kernel irqchip can tell the GIC to use PPIs designated for
specific cpus. The irq field is interpreted like this:
bits: | 31 ... 24 | 23 ... 16 | 15 ... 0 |
field: | irq_type | vcpu_index | irq_number |
The irq_type field has the following values:
- irq_type[0]: out-of-kernel GIC: irq_number 0 is IRQ, irq_number 1 is FIQ
- irq_type[1]: in-kernel GIC: SPI, irq_number between 32 and 1019 (incl.)
(the vcpu_index field is ignored)
- irq_type[2]: in-kernel GIC: PPI, irq_number between 16 and 31 (incl.)
The irq_number thus corresponds to the irq ID in as in the GICv2 specs.
This is documented in Documentation/kvm/api.txt.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
Targets KVM support for Cortex A-15 processors.
Contains all the framework components, make files, header files, some
tracing functionality, and basic user space API.
Only supported core is Cortex-A15 for now.
Most functionality is in arch/arm/kvm/* or arch/arm/include/asm/kvm_*.h.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <c.dall@virtualopensystems.com>
This makes the device core auto-grab the pinctrl handle and set
the "default" (PINCTRL_STATE_DEFAULT) state for every device
that is present in the device model right before probe. This will
account for the lion's share of embedded silicon devcies.
A modification of the semantics for pinctrl_get() is also done:
previously if the pinctrl handle for a certain device was already
taken, the pinctrl core would return an error. Now, since the
core may have already default-grabbed the handle and set its
state to "default", if the handle was already taken, this will
be disregarded and the located, previously instanitated handle
will be returned to the caller.
This way all code in drivers explicitly requesting their pinctrl
handlers will still be functional, and drivers that want to
explicitly retrieve and switch their handles can still do that.
But if the desired functionality is just boilerplate of this
type in the probe() function:
struct pinctrl *p;
p = devm_pinctrl_get_select_default(&dev);
if (IS_ERR(p)) {
if (PTR_ERR(p) == -EPROBE_DEFER)
return -EPROBE_DEFER;
dev_warn(&dev, "no pinctrl handle\n");
}
The discussion began with the addition of such boilerplate
to the omap4 keypad driver:
http://marc.info/?l=linux-input&m=135091157719300&w=2
A previous approach using notifiers was discussed:
http://marc.info/?l=linux-kernel&m=135263661110528&w=2
This failed because it could not handle deferred probes.
This patch alone does not solve the entire dilemma faced:
whether code should be distributed into the drivers or
if it should be centralized to e.g. a PM domain. But it
solves the immediate issue of the addition of boilerplate
to a lot of drivers that just want to grab the default
state. As mentioned, they can later explicitly retrieve
the handle and set different states, and this could as
well be done by e.g. PM domains as it is only related
to a certain struct device * pointer.
ChangeLog v4->v5 (Stephen):
- Simplified the devicecore grab code.
- Deleted a piece of documentation recommending that pins
be mapped to a device rather than hogged.
ChangeLog v3->v4 (Linus):
- Drop overzealous NULL checks.
- Move kref initialization to pinctrl_create().
- Seeking Tested-by from Stephen Warren so we do not disturb
the Tegra platform.
- Seeking ACK on this from Greg (and others who like it) so I
can merge it through the pinctrl subsystem.
ChangeLog v2->v3 (Linus):
- Abstain from using IS_ERR_OR_NULL() in the driver core,
Russell recently sent a patch to remove it. Handle the
NULL case explicitly even though it's a bogus case.
- Make sure we handle probe deferral correctly in the device
core file. devm_kfree() the container on error so we don't
waste memory for devices without pinctrl handles.
- Introduce reference counting into the pinctrl core using
<linux/kref.h> so that we don't release pinctrl handles
that have been obtained for two or more places.
ChangeLog v1->v2 (Linus):
- Only store a pointer in the device struct, and only allocate
this if it's really used by the device.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Mitch Bradley <wmb@firmworks.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Rickard Andersson <rickard.andersson@stericsson.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[swarren: fixed and simplified error-handling in pinctrl_bind_pins(), to
correctly handle deferred probe. Removed admonition from docs not to use
pinctrl hogs for devices]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds host phy support to samsung-usbphy driver and
further adds support for samsung's exynos5250 usb-phy.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
'report_lost_ticks' parameter has been removed back in 2007 through
1489939f0a ("time: x86_64: convert x86_64 to use GENERIC_TIME").
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The relation between PIN_BANK numbers and pio letters wasn't made very
clear.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The 'security.ima' extended attribute may contain either the file data's
hash or a digital signature. This patch adds support for requiring a
specific extended attribute type. It extends the IMA policy with a new
keyword 'appraise_type=imasig'. (Default is hash.)
Changelog v2:
- Fixed Documentation/ABI/testing/ima_policy option syntax
Changelog v1:
- Differentiate between 'required' vs. 'actual' extended attribute
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Paul Gortmaker says:
====================
The Ethernet-HowTo was maintained for roughly 10 years, from 1993 to 2003.
Fortunately sane hardware probing and auto detection (via PCI and ISA/PnP)
largely made the document a relic of the past, hence it being abandoned
a decade ago.
However, there is one last useful thing that we can extract from the
effort made in maintaining that document. We can use it to guide us
with respect to what rare, experimental and/or super ancient 10Mbit
ISA drivers don't make sense to maintain in-tree anymore.
Nobody will argue that ISA is obsolete. Availability went away at about
the time Pentium3 motherboards moved from 500MHz Slot1/SECC processors
to the green 500MHz Socket 370 Pentium3 chips, at the turn of the century.
In theory, it is possible that someone could still be running one of these
12+ year old P3 machines and want 3.9+ bleeding edge kernels (but unlikely).
In light of the above (remote) possibility, we can defer the removal of some
ISA network drivers that were highly popular and well tested. Typically
that means the stuff more from the mid to late '90s, some with ISA PnP
support, like the 3c509, the wd/SMC 8390 based stuff, PCnet/lance etc.
But a lot of other drivers, typically from the early 1990s were for rare
hardware, and experimental (to the point of requiring a cron job that would
do a test ping, and then ifconfig down/up and/or a rmmod/insmod!). And
some of these drivers (znet, and lp486e to name two) are physically tied
to platforms with on motherboard ethernet -- of 486 machines that date
from the early 1990s and can only have single digit amounts of memory.
What I'd like to achieve here with this series, is to get rid of those old
drivers that are no longer being used. In an earlier discussion where
I'd proposed deleting a single driver, Alan suggested we instead dump
all the historical stuff in one go, to make it "...immediately obvious
where the break point is..."[1] and that it was "perfectly reasonable it
(and a pile of other ISA cards) ought to be shown the door"[2]. So that
is the goal here - make a clear line in the sand where the really ancient
stuff finally gets kicked to the curb.
Two old parallel port drivers are considered for removal here as well,
since in early 386/486 ISA machines, the parallel port was typically found
with the UARTS on the multi-I/O ISA controller card. These drivers also date
from the early 1990's; parallel ports are no longer found on modern boards,
and their performance was not even capable of 10% of 10Mbit bandwidth.
Allow me a preemptive justification against the inevitable comments from
well meaning bystanders who suggest "why not just leave all this alone?".
Dead drivers cost us all if they are left in tree. If you think that
is false, then please first consider:
-every time you type "git status", you are checking to see if modifications
have been made by you to all that dead code.
-every time you type "git grep <regex>" you are searching through files
which contain that dead code that simply does not interest you.
-every time you build a "allyesconfig" and an "allmodconfig" (don't tell
me you skip this step before submitting your changes to a maintainer),
you waste CPU cycles building this dead code.
-every time there is a tree wide API change, or cleanup, or file relocation,
we pay the cost of updating dead code, or moving dead code.
-daily regression tests (take linux-next as the most transparent
example) spend time building (and possibly running) this dead code.
-hard working people who regularly run auditing tools looking for lurking
bugs (sparse/coverity/smatch/coccinelle) are wasting time checking for,
and fixing bugs in this dead code.
This last one is key. Please take a look at the git history for the
files that are proposed for removal here. Look at the git history for
any one of them ("git whatchanged --follow drivers/net/.../driver.c")
Mentally sort the changes into two bins -- (1) the robotic tree-wide
changes, and (2) the "look I found a real run-time bug while using this"
category. You will see that category #2 is essentially empty.
Further to that, realize that drivers don't simply disappear. We are
not operating in the binary-only distribution space like other OS. All
these drivers remain in the git history forever. If a person is an
enthusiast for extreme legacy hardware, they are probably already
customizing their kernel source and building it themselves to support
such systems. Also keep in mind that they could still build the 3.8
kernel exactly as-is, and run it (or a 3.8.x stable variant of it) for
several more years if they were really determined to cling to these old
experimental ISA drivers for some reason.
In summary, I hope that folks can be pragmatic about this, and not
get swept up in nostalgia. Ask yourself whether it is realistic to
expect a person would have a genuine use case where they would
need to build a 3.9+ modern kernel and install it on some legacy hardware
that has no option but to absolutely _require_ one of the drivers
that are deleted here.
The following series was created with --irreversible-delete for
ease of review (it skips showing the content of files that are
deleted); however the complete patches can be pulled as per below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we have removed NCE (Neighbour Cache Entry) reference from
routing entries, the only refcnt holders of an NCE are its timer
(if running) and its owner table, in usual cases. As a result,
neigh_periodic_work() purges NCEs over and over again even for
gateways.
It does not make sense to purge entries, if number of them is
very small, so keep them. The minimum number of entries to keep
is specified by gc_thresh1.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Support swap file and link generic_file_remap_pages
o Enhance the bio streaming flow and free section control
o Major bug fix on recovery routine
o Minor bug/warning fixes and code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJQ/fpIAAoJEEAUqH6CSFDS6BAP/jz/JIPoSu4NunWgVH68tzA4
xx4lsmJQJQG+1241uA9v4MMkcTzxE0QVNTOX3BpUXBhCMc00aPOPWlWjULridLI9
0vRE6LpG+NntkyKF+M5T1ydGuQoDlEvqoGs6c5p3yaI6PxzbzmBmipsmqXUA8fyu
280+OWJoAcALEMJiQ8JsHcDmvM9wdQ+BV/j3BNCm4dqBUA4dYPfDzRKUJYfwqiig
qmVRseJJaekxrQ2lHG/K/WPAXa8aRcV6khP9tv/BPGRMt+I/fli/J4sWEFT6c73B
+qYmhrf/RLNJ1O13dePlo3URwMu083PL8QN355GAKUJbMaX/UPjEnq0DLbBOkCS2
KBQI5O1eiFauEE6YU7p7GuvnLeVkukcXSQNVnRrnWzTUA9CMThZZ2mAgb2lz+iEP
oZWNirRwnxdcTQRXjPyTCtpPTCgJi4GO1WS5s6HeLP8G8Muo4PzDzcEwMX0Mw5ih
s4n4wpQ+Zp3h53cc/DxdFAK15uM3XYtUfb92kJwqaEG5VmBy6KvliXDRnNXg7WMI
imCb08c0Fr0M8ZHOd+UCveICcndFj25jkjx8w7PoE1KBbGJkKf+cjpZ3OhOAliux
sGtH3EZLV6jx1MjV79OpDXQGoVsvktesCbRcaxc7BbqljXYVNiap8QbzjPnmAt6z
KKN0GU32eolGgK4Zd/iF
=vJQc
-----END PGP SIGNATURE-----
Merge tag 'f2fs-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs fixes from Jaegeuk Kim:
o Support swap file and link generic_file_remap_pages
o Enhance the bio streaming flow and free section control
o Major bug fix on recovery routine
o Minor bug/warning fixes and code cleanups
* tag 'f2fs-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (22 commits)
f2fs: use _safe() version of list_for_each
f2fs: add comments of start_bidx_of_node
f2fs: avoid issuing small bios due to several dirty node pages
f2fs: support swapfile
f2fs: add remap_pages as generic_file_remap_pages
f2fs: add __init to functions in init_f2fs_fs
f2fs: fix the debugfs entry creation path
f2fs: add global mutex_lock to protect f2fs_stat_list
f2fs: remove the blk_plug usage in f2fs_write_data_pages
f2fs: avoid redundant time update for parent directory in f2fs_delete_entry
f2fs: remove redundant call to set_blocksize in f2fs_fill_super
f2fs: move f2fs_balance_fs to punch_hole
f2fs: add f2fs_balance_fs in several interfaces
f2fs: revisit the f2fs_gc flow
f2fs: check return value during recovery
f2fs: avoid null dereference in f2fs_acl_from_disk
f2fs: initialize newly allocated dnode structure
f2fs: update f2fs partition info about SIT/NAT layout
f2fs: update f2fs document to reflect SIT/NAT layout correctly
f2fs: remove unneeded INIT_LIST_HEAD at few places
...
This patch adds support for "earlyprintk=" parameter on the kernel
command line. The format is:
earlyprintk=<name>[,<addr>][,<options>]
where <name> is the name of the (UART) device, e.g. "pl011", <addr> is
the I/O address. The <options> aren't currently used.
The mapping of the earlyprintk device is done very early during kernel
boot and there are restrictions on which functions it can call. A
special early_io_map() function is added which creates the mapping from
the pre-defined EARLY_IOBASE to the device I/O address passed via the
kernel parameter. The pgd entry corresponding to EARLY_IOBASE is
pre-populated in head.S during kernel boot.
Only PL011 is currently supported and it is assumed that the interface
is already initialised by the boot loader before the kernel is started.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The devm_request_and_ioremap() function is very useful and helps avoid a
whole lot of boilerplate. However, one issue that keeps popping up is
its lack of a specific error code to determine which of the steps that
it performs failed. Furthermore, while the function gives an example and
suggests what error code to return on failure, a wide variety of error
codes are used throughout the tree.
In an attempt to fix these problems, this patch adds a new function that
drivers can transition to. The devm_ioremap_resource() returns a pointer
to the remapped I/O memory on success or an ERR_PTR() encoded error code
on failure. Callers can check for failure using IS_ERR() and determine
its cause by extracting the error code using PTR_ERR().
devm_request_and_ioremap() is implemented as a wrapper around the new
API and return NULL on failure as before. This ensures that backwards
compatibility is maintained until all users have been converted to the
new API, at which point the old devm_request_and_ioremap() function
should be removed.
A semantic patch is included which can be used to convert from the old
devm_request_and_ioremap() API to the new devm_ioremap_resource() API.
Some non-trivial cases may require manual intervention, though.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is another one that makes sense to target for obsolescence, since
it (a)appeared pre-1995, and (b)was rather rare, and (c)did not
really have any statistically significant active linux user base.
Removing this ISA 10Mbit driver support is unlikely to be even noticed
by the user base of 3.9+ linux kernels, especially when the documentation
clearly indicates the vintage with this text:
"...designed to work with all kernels > 1.1.33"
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These are old ISA 10Mbit cards from the 1st 1/2 of the 1990s and
required manual jumper settings in order to configure them. Here
we remove them on the premise that they are no longer used in any
modern 3.9+ kernels.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The parallel port is largely replaced by USB, and even in the
day where these drivers were current, the documented speed was
less than 100kB/s. Let us not pretend that anyone cares about
these drivers anymore, or worse - pretend that anyone is using
them on a modern kernel.
As a side bonus, this is the end of legacy parallel port ethernet,
so we get to drop the whole chunk relating to that in the legacy
Space.c file containing the non-PCI unified probe dispatch.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The Allwinner SoCs have an IP module that handle both the muxing and the
GPIOs.
This IP has 8 banks of 32 bits, with a number of pins actually useful
for each of these banks varying from one to another, and depending on
the SoC used on the board.
This driver only implements the pinctrl part, the gpio part will come
eventually.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SiRFmarco is a dual-core cortex-a9 SMP SoC from CSR. this patch
adds the .dtsi and a basic evb board .dts for it.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Rob Landley <rob@landley.net>
CC: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The non-dt probing allowed passing the location via platform data from
the beginning. So make up leeway for device tree probing.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original intent of this file was to list limitations in
drivers/hardware relating to multicast use, back when some
modest hardware from the early 1990s did not support things
we might take for granted today.
I was intending to delete some now-gone MCA/token ring entries
in this file, but once I opened it, I found it only contained
information on the earliest (pre-2000) linux networking drivers.
Checking the git history shows that the file hasn't been touched
since 2005. Clearly nobody is actively consulting this file
as a meaningful reference.
Rather than add a "YES YES YES" line for all of the drivers we
currently have, lets just take advantage of the fact that nobody
is using the file to delete it.
This has the side benefit of not having to do a line-by-line
deletion of the file content as each older driver is expired.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I grepped through the code and picked bits about nf_conntrack sysctl api
and put that into one documentation file.
[ I have mangled this patch including comments from several grammar
improvements proposed by Neal Murphy <neal.p.murphy@alum.wpi.edu>,
any new grammar error is my mistake --pablo ]
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some platforms provide usb port connect types through ACPI. This
patch is to add this new attribute to expose these information
to user space.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aim of this locking rework is that ioctls which a compositor should be
might call for every frame (set_cursor, page_flip, addfb, rmfb and
getfb/create_handle) should not be able to block on kms background
activities like output detection. And since each EDID read takes about
25ms (in the best case), that always means we'll drop at least one frame.
The solution is to add per-crtc locking for these ioctls, and restrict
background activities to only use the global lock. Change-the-world type
of events (modeset, dpms, ...) need to grab all locks.
Two tricky parts arose in the conversion:
- A lot of current code assumes that a kms fb object can't disappear while
holding the global lock, since the current code serializes fb
destruction with it. Hence proper lifetime management using the already
created refcounting for fbs need to be instantiated for all ioctls and
interfaces/users.
- The rmfb ioctl removes the to-be-deleted fb from all active users. But
unconditionally taking the global kms lock to do so introduces an
unacceptable potential stall point. And obviously changing the userspace
abi isn't on the table, either. Hence this conversion opportunistically
checks whether the rmfb ioctl holds the very last reference, which
guarantees that the fb isn't in active use on any crtc or plane (thanks
to the conversion to the new lifetime rules using proper refcounting).
Only if this is not the case will the code go through the slowpath and
grab all modeset locks. Sane compositors will never hit this path and so
avoid the stall, but userspace relying on these semantics will also not
break.
All these cases are exercised by the newly added subtests for the i-g-t
kms_flip, tested on a machine where a full detect cycle takes around 100
ms. It works, and no frames are dropped any more with these patches
applied. kms_flip also contains a special case to exercise the
above-describe rmfb slowpath.
* 'drm-kms-locking' of git://people.freedesktop.org/~danvet/drm-intel: (335 commits)
drm/fb_helper: check whether fbcon is bound
drm/doc: updates for new framebuffer lifetime rules
drm: don't hold crtc mutexes for connector ->detect callbacks
drm: only grab the crtc lock for pageflips
drm: optimize drm_framebuffer_remove
drm/vmwgfx: add proper framebuffer refcounting
drm/i915: dump refcount into framebuffer debugfs file
drm: refcounting for crtc framebuffers
drm: refcounting for sprite framebuffers
drm: fb refcounting for dirtyfb_ioctl
drm: don't take modeset locks in getfb ioctl
drm: push modeset_lock_all into ->fb_create driver callbacks
drm: nest modeset locks within fpriv->fbs_lock
drm: reference framebuffers which are on the idr
drm: revamp framebuffer cleanup interfaces
drm: create drm_framebuffer_lookup
drm: revamp locking around fb creation/destruction
drm: only take the crtc lock for ->cursor_move
drm: only take the crtc lock for ->cursor_set
drm: add per-crtc locks
...
Now that framebuffer are reference-counted for all use-sites, update
the documentation accordingly to stress the new rules for
initialization and teardown.
Also add a short paragraph about the implications for drivers of the
new locking rules.
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And do a quick pass to adjust them to the last few (years?) of changes
...
This time actually compile-tested ;-)
Reviewed-by: Rob Clark <rob@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A description was lacking how to write an EDID firmware file that
corresponds to a given X11 setting.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this patche deletes hard code that registers clkdev by things like:
clk_register_clkdev(clk, NULL, "b0030000.nand");
clk_register_clkdev(clk, NULL, "b0040000.audio");
clk_register_clkdev(clk, NULL, "b0080000.usp");
prima2 clock controller becomes a clock provider and every dt node
just declares its clock sources by dt prop.
it also makes us easier to extend this driver to support both prima2
and marco as marco has different address mapping with prima2.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This adds a driver for the Tegra114 pinmux, and required
parameterization data for Tegra114.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra114-pinmux".
Originally written by Pritesh.
ldewangan:
- cleanup the patches,
- remove non-require tables.
- Use module_platform_driver() for driver registartion.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding support to parse device node data in order to get
required properties to set pmu isolation for usb-phy.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This driver uses usb_phy interface to interact with s3c-hsotg. Supports
phy_init and phy_shutdown functions to enable/disable usb phy. Support
will be extended to host controllers and more Samsung SoCs.
Signed-off-by: Praveen Paneri <p.paneri@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Introduce print_hex_dump_debug() that can be dynamically controlled, similar to
pr_debug.
Also, make print_hex_dump_bytes() dynamically controlled
Implement only 'p' flag (_DPRINTK_FLAGS_PRINT) to keep it simple since hex dump prints
multiple lines and long prefix would impact readability.
To provide line/file etc. information, use pr_debug or similar
before/after print_hex_dump_debug()
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NVIDIA's Tegra KBC has maximum 24 pins to make matrix keypad.
Any pin can be configured as row or column. The maximum column pin
can be 8 and maximum row pin can be 16.
Remove the assumption that all first 16 pins will be used as row
and remaining as columns and Add the property for configuring pins
to either row or column from DT. Update the devicetree binding
document accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
While a privileged program can open a raw socket, attach some
restrictive filter and drop its privileges (or send the socket to an
unprivileged program through some Unix socket), the filter can still
be removed or modified by the unprivileged program. This commit adds a
socket option to lock the filter (SO_LOCK_FILTER) preventing any
modification of a socket filter program.
This is similar to OpenBSD BIOCLOCK ioctl on bpf sockets, except even
root is not allowed change/drop the filter.
The state of the lock can be read with getsockopt(). No error is
triggered if the state is not changed. -EPERM is returned when a user
tries to remove the lock or to change/remove the filter while the lock
is active. The check is done directly in sk_attach_filter() and
sk_detach_filter() and does not affect only setsockopt() syscall.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a very simple machine driver using the Wolfson wm9712 AC97
codec.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* DT binding for arc-uart
* With alll the bits in place we can now use DT probing.
Note that there's a bit of kludge right now because earlyprintk portion
of driver can't use the DT infrastrcuture to get resoures/plat_data.
This requires some infrastructre changes to of_flat_ framework
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Cox <alan@linux.intel.com>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA's Tegra has multiple UART controller which supports:
- APB DMA based controller fifo read/write.
- End Of Data interrupt in incoming data to know whether end
of frame achieve or not.
- HW controlled RTS and CTS flow control to reduce SW overhead.
Add serial driver to use all above feature.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core is using power states lifted from ACPI for no
good reason. Remove this reference from the documentation and
alter all users to use an enum specific to the serial core
instead, and define it in <linux/serial_core.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the function thermal_generate_netlink_event
to receive a thermal zone device instead of a originator id.
This way, the messages will always be bound to a thermal zone.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch adds basic DT bindings for OMAP GPMC.
The actual peripherals are instantiated from child nodes within the GPMC
node, and the only type of device that is currently supported is NAND.
Code was added to parse the generic GPMC timing parameters and some
documentation with examples on how to use them.
Successfully tested on an AM33xx board.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[tony@atomide.com: updated to apply]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for loading the Renesas FSI driver via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds the driver for the Tegra 2x AC97 host controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This series is based on:
git://server.prisktech.co.nz/git/linuxwmt.git tags/vt8500-multiplatform-3.9
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ8NEiAAoJEAKiPfwuf9N/F0gH/0fAJkX6qPxVe33yPDbMFE1/
fKzPNM/FtzZh72updnNPKvAkO+V8ybDWo8tkn/nyvC7wNYNTFhlcFIc/zFyIwL1W
H2gcIl8aygdee6pRkigIi0alkK1ZHgClmdKJXnCv0nyHWLXqQCeiqCgAUYLBwfPA
4ZoVLs7djWiSF9TP51hDRbeG4Rzn38GQMxO8cmnk5qitfPc06hDP5Z6Hu8oLTXRn
ekGZI6aOqFz+RBHGGtQ813wH+kWrHu3/VHz8DPAVZ5KKz5bDFgcwcp07xQXCbfgX
kS2JytpJ+5Rmh6XVLTPNrxeaqht8MUwdL327rEVi0UO3z7CmYmVBf/6ajWW+QBU=
=Q4oq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-3.9' of git://server.prisktech.co.nz/git/linuxwmt into next/soc
From Tony Prisk:
Add support for WM8750 and WM8850 SoCs.
* tag 'armsoc-3.9' of git://server.prisktech.co.nz/git/linuxwmt:
arm: vt8500: Add support for Wondermedia WM8750/WM8850
arm: vt8500: Remove remaining mach includes
arm: vt8500: Convert debug-macro.S to be multiplatform friendly
arm: vt8500: Remove single platform Kconfig options
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for the WM8750 (ARMv6) and WM8850 (ARMv7).
Devicetree documentation is updated for new SoCs.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Output of a git grep happened to make me look into this file, and
I found instructions about how to hand patch (without using patch)
the driver into the kernel tree.
Since the driver has been a part of the mainline kernel for years,
we can dump this whole section. Fortunately it doesn't even cause
a renumbering of the sections to do so.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements pin multiplexing and pin configuration for
the Nomadik pin controller using the device tree.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Rob Landley <rob@landley.net>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Masanari Iida <standby24x7@gmail.com>
CC: Jason Wessel <jason.wessel@windriver.com>
CC: Richard L Maliszewski <richard.l.maliszewski@intel.com>
CC: Gang Wei <gang.wei@intel.com>
CC: Shane Wang <shane.wang@intel.com>
CC: Harry Wei <harryxiyou@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Tejun writes:
Hello, Jens.
Please consider pulling from the following branch to receive cfq blkcg
hierarchy support. The branch is based on top of v3.8-rc2.
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup.git blkcg-cfq-hierarchy
The patchset was reviewd in the following thread.
http://thread.gmane.org/gmane.linux.kernel.cgroups/5571
Recent commit (commit 7e3a2dc529 doc: make the description of how tcp_ecn
works more explicit and clear ) clarified the behavior of tcp_ecn sysctl
variable but description is inconsistent. When requested by incoming conections,
ECN is enabled with not just tcp_ecn = 2 but also with tcp_ecn = 1.
This patch makes it clear that with tcp_ecn = 1, ECN is enabled when requested
by incoming connections.
Also fix spelling of 'incoming'.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new devicetree binding for describing PSCI firmware
to Linux.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We need to be able to read and write the contents of the EPR register
from user space.
This patch implements that logic through the ONE_REG API and declares
its (never implemented) SREGS counterpart as deprecated.
Signed-off-by: Alexander Graf <agraf@suse.de>
The External Proxy Facility in FSL BookE chips allows the interrupt
controller to automatically acknowledge an interrupt as soon as a
core gets its pending external interrupt delivered.
Today, user space implements the interrupt controller, so we need to
check on it during such a cycle.
This patch implements logic for user space to enable EPR exiting,
disable EPR exiting and EPR exiting itself, so that user space can
acknowledge an interrupt when an external interrupt has successfully
been delivered into the guest vcpu.
Signed-off-by: Alexander Graf <agraf@suse.de>
Support for loading the ak4642 codec module via devicetree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reflect the uapi folder change in SREGS API documentation.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Reviewed-by: Amos Kong <kongjianjun@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The pn544 driver no longer has a /dev/pn544 interface nor a sysfs one.
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the previous two patches, all cfqg scheduling decisions are based
on vfraction and ready for hierarchy support. The only thing which
keeps the behavior flat is cfqg_flat_parent() which makes vfraction
calculation consider all non-root cfqgs children of the root cfqg.
Replace it with cfqg_parent() which returns the real parent. This
enables full blkcg hierarchy support for cfq-iosched. For example,
consider the following hierarchy.
root
/ \
A:500 B:250
/ \
AA:500 AB:1000
For simplicity, let's say all the leaf nodes have active tasks and are
on service tree. For each leaf node, vfraction would be
AA: (500 / 1500) * (500 / 750) =~ 0.2222
AB: (1000 / 1500) * (500 / 750) =~ 0.4444
B: (250 / 750) =~ 0.3333
and vdisktime will be distributed accordingly. For more detail,
please refer to Documentation/block/cfq-iosched.txt.
v2: cfq-iosched.txt updated to describe group scheduling as suggested
by Vivek.
v3: blkio-controller.txt updated.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Change the power_save_controller option to bint from bool so that user
can override the runtime PM capability bit and force to enable or
disable the runtime PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support to set polarity on PWM devices, allowing for inverted
duty cycles.
Also update the binding document to #pwm-cells = <3> to allow
passing the flags from devicetree.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
People are back from the holiday breaks, and it shows. Here are a bunch of
fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups,
a few __init annotation fixes and some error handling improvement
in their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to see
here, mostly from the OMAP PM changes, but nothing overly crazy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9fE
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
Update the netconsole document as well.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add atomic_xchg() to documentation for atomic operations and
memory barriers.
Signed-off-by: Richard Braun <rbraun@sceen.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The as-documented rcu_nocb_poll will fail to enable this feature
for two reasons. (1) there is an extra "s" in the documented
name which is not in the code, and (2) since it uses module_param,
it really is expecting a prefix, akin to "rcutree.fanout_leaf"
and the prefix isn't documented.
However, there are several reasons why we might not want to
simply fix the typo and add the prefix:
1) we'd end up with rcutree.rcu_nocb_poll, and rather probably make
a change to rcutree.nocb_poll
2) if we did #1, then the prefix wouldn't be consistent with the
rcu_nocbs=<cpumap> parameter (i.e. one with, one without prefix)
3) the use of module_param in a header file is less than desired,
since it isn't immediately obvious that it will get processed
via rcutree.c and get the prefix from that (although use of
module_param_named() could clarify that.)
4) the implied export of /sys/module/rcutree/parameters/rcu_nocb_poll
data to userspace via module_param() doesn't really buy us anything,
as it is read-only and we can tell if it is enabled already without
it, since there is a printk at early boot telling us so.
In light of all that, just change it from a module_param() to an
early_setup() call, and worry about adding it to /sys later on if
we decide to allow a dynamic setting of it.
Also change the variable to be tagged as read_mostly, since it
will only ever be fiddled with at most, once at boot.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7Dk+AAoJEFBXWFqHsHzOUugIAJZblDy7ORFZhW0R8L4Be541
pS5aBGFY7VYCrL9BGUKGsLuITI+arbYFHc+H4nqhNMBAvgChPxJZMnaG4kp1Q5Vm
AVr9tNrwsauVHLlryUk4ekut4G4WWo1NDcFq4S6rxD/jxA/uP6rnMUCY6PX4LLL9
ZpGDb3BWQ2bbUaANu3cjc1I1/Gle1ir9LObm6ZC6l8MHTTG7hyTMHvS8eCZzmDbc
9z01ZrvTKn1AneeHOpArd2/jo14b6Kap8ykx2hdVUeBhIbZp3pomezZau9ya8/kB
+1BQVODdkOMzBm6gkIkfU3HbUPnIPL18MG/uKyD+f67YkX5YODinUVdq63upLxc=
=7yrS
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
It includes one critical fix - wrong flexcan2 clock will hang system
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
* tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mx5: Fix MX53 flexcan2 clock
ARM: dts: imx31-bug: Fix manufacturer compatible string
clk: imx: Remove 'clock-output-names' from the examples
This patch adds a PWM driver based on Atmel Timer Counter Block. The
Timer Counter Block is used in Waveform generator mode.
A Timer Counter Block provides up to 6 PWM devices grouped by 2:
* group 0 = PWM 0 and 1
* group 1 = PWM 2 and 3
* group 2 = PMW 4 and 5
PWM devices in a given group must be configured with the same period
value. If a PWM device in a group tries to change the period value and
the other device is already configured with a different value an error
will be returned.
This driver requires device tree support. The Timer Counter Block number
used to create a PWM chip is given by the tc-block field in an
"atmel,tcb-pwm" compatible node.
This patch was tested on kizbox board (at91sam9g20 SoC) with pwm-leds.
Signed-off-by: Boris BREZILLON <linux-arm@overkiz.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Pull networking fixes from David Miller:
1) New sysctl ndisc_notify needs some documentation, from Hanns
Frederic Sowa.
2) Netfilter REJECT target doesn't set transport header of SKB
correctly, from Mukund Jampala.
3) Forcedeth driver needs to check for DMA mapping failures, from Larry
Finger.
4) brcmsmac driver can't use usleep_range while holding locks, use
udelay instead. From Niels Ole Salscheider.
5) Fix unregister of netlink bridge multicast database handlers, from
Vlad Yasevich and Rami Rosen.
6) Fix checksum calculations in netfilter's ipv6 network prefix
translation module.
7) Fix high order page allocation failures in netfilter xt_recent, from
Eric Dumazet.
8) mac802154 needs to use netif_rx_ni() instead of netif_rx() because
mac802154_process_data() can execute in process rather than
interrupt context. From Alexander Aring.
9) Fix splice handling of MSG_SENDPAGE_NOTLAST, otherwise we elide one
tcp_push() too many. From Eric Dumazet and Willy Tarreau.
10) Fix skb->truesize tracking in XEN netfront driver, from Ian
Campbell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
xen/netfront: improve truesize tracking
ipv4: fix NULL checking in devinet_ioctl()
tcp: fix MSG_SENDPAGE_NOTLAST logic
net/ipv4/ipconfig: really display the BOOTP/DHCP server's address.
ip-sysctl: fix spelling errors
mac802154: fix NOHZ local_softirq_pending 08 warning
ipv6: document ndisc_notify in networking/ip-sysctl.txt
ath9k: Fix Kconfig for ATH9K_HTC
netfilter: xt_recent: avoid high order page allocations
netfilter: fix missing dependencies for the NOTRACK target
netfilter: ip6t_NPT: fix IPv6 NTP checksum calculation
bridge: add empty br_mdb_init() and br_mdb_uninit() definitions.
vxlan: allow live mac address change
bridge: Correctly unregister MDB rtnetlink handlers
brcmfmac: fix parsing rsn ie for ap mode.
brcmsmac: add copyright information for Canonical
rtlwifi: rtl8723ae: Fix warning for unchecked pci_map_single() call
rtlwifi: rtl8192se: Fix warning for unchecked pci_map_single() call
rtlwifi: rtl8192de: Fix warning for unchecked pci_map_single() call
rtlwifi: rtl8192ce: Fix warning for unchecked pci_map_single() call
...
dw_dmac driver already supports device tree but it used to have its platform
data passed the non-DT way.
This patch does following changes:
- pass platform data via DT, non-DT way still takes precedence if both are used.
- create generic filter routine
- Earlier slave information was made available by slave specific filter routines
in chan->private field. Now, this information would be passed from within dmac
DT node. Slave drivers would now be required to pass bus_id (a string) as
parameter to this generic filter(), which would be compared against the slave
data passed from DT, by the generic filter routine.
- Update binding document
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Fixed __devinit usage]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* Removal of some ACPICA code that the kernel will never use from Lv Zheng.
* APEI fix from Adrian Huang.
* Removal of unnecessary ACPI memory hotplug driver code from Liu Jinsong.
* Minor ACPI power management fixes.
* ACPI debug code fix from Joe Perches.
* ACPI fix to make system bus device nodes get the right names.
* PNP resources handling fixes from Witold Szczeponik.
* cpuidle fix for a recent regression stalling boot on systems with great
numbers of CPUs from Daniel Lezcano.
* cpuidle fixes from Sivaram Nair.
* intel_idle debug message fix from Youquan Song.
* cpufreq build regression fix from Larry Finger.
* cpufreq fix for an obscure initialization race related to statistics from
Konstantin Khlebnikov.
* cpufreq change disabling the Longhaul driver by default from Rafał Bilski.
* PM core fix preventing device suspend errors from happening during system
suspend due to obscure race conditions.
* PM QoS local variable name cleanup.
--
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQ61zgAAoJEKhOf7ml8uNsaYsQAK6EXORIIIvHtudjkcxcOxPp
pQaHQ1/YHjxoO3N/dZpjgbozwSnkrf5iJs6BaN+LpbqLS3eRJDEJm3Hx8YAkt+bx
ZcMUlPqr90W5AXvjlbJjyHIrupOX7TChgyyC0a8uTvDSylJMimWtEGn/VeYVRaCs
GLfyVmDwMlMmC85vK+x27IoUxNuGzPiGx2s//thHv4HRL7d+5xn2Da0AHPSeZTZe
ZuNCyWKwVzpJ8mjclAOTtwMUHGYys0x+T+7wa5IZq4yH0gEQZoKfLGW3uOg+h4R5
wp8XhipORQh5A1AMGpC3bDhsplGggL1ImN2k50h4lKIAtpY8t1m++63i7hHiHX1I
mfvNyinMJsnud80AZN5MgMAqykYDvgwO562LmaSBc+zNq2B1cfHuex9iA7CC+WAY
5IKxN3EGPyQomkBRSYGnAEKw5jvktPMRT6JuLjLiwaz7NcWN72lWv66Xq34RLEld
zZavCmo+fS7PWk5ofNh4RDrH+Zi02XixsgycmeKFxG+U1i/aM6tO3t9fcetUzIlJ
JqCHAjyA8AyCApbm4GgVQBkw1MP8SsXeJ3FnYynx8n23EmHvh7gIUiG/Hk1vOEpF
0ExwJMOOTXcv5BcfoCoF0VBJNBGq1wzipwN43Nj55LLUfJ4Ovp/T+ySXOc6seb3C
nqx2e4VzVs0Gu2Cdt+wy
=k35e
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Removal of some ACPICA code that the kernel will never use from Lv
Zheng.
- APEI fix from Adrian Huang.
- Removal of unnecessary ACPI memory hotplug driver code from Liu
Jinsong.
- Minor ACPI power management fixes.
- ACPI debug code fix from Joe Perches.
- ACPI fix to make system bus device nodes get the right names.
- PNP resources handling fixes from Witold Szczeponik.
- cpuidle fix for a recent regression stalling boot on systems with
great numbers of CPUs from Daniel Lezcano.
- cpuidle fixes from Sivaram Nair.
- intel_idle debug message fix from Youquan Song.
- cpufreq build regression fix from Larry Finger.
- cpufreq fix for an obscure initialization race related to statistics
from Konstantin Khlebnikov.
- cpufreq change disabling the Longhaul driver by default from Rafał
Bilski.
- PM core fix preventing device suspend errors from happening during
system suspend due to obscure race conditions.
- PM QoS local variable name cleanup.
* tag 'pm+acpi-for-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Move disabling/enabling runtime PM to late suspend/early resume
PM / QoS: Rename local variable in dev_pm_qos_add_ancestor_request()
ACPI / scan: Do not use dummy HID for system bus ACPI nodes
cpufreq / governor: Fix problem with cpufreq_ondemand or cpufreq_conservative
cpufreq / Longhaul: Disable driver by default
cpufreq / stats: fix race between stats allocation and first usage
cpuidle: fix lock contention in the idle path
intel_idle: pr_debug information need separated
cpuidle / coupled: fix ready counter decrement
cpuidle: Fix finding state with min power_usage
PNP: Handle IORESOURCE_BITS in resource allocation
PNP: Simplify setting of resources
ACPI / power: Remove useless message from device registering routine
ACPI / glue: Update DBG macro to include KERN_DEBUG
ACPI / PM: Do not apply ACPI_SUCCESS() to acpi_bus_get_device() result
ACPI / memhotplug: remove redundant logic of acpi memory hotadd
ACPI / APEI: Fix the returned value in erst_dbg_read
ACPICA: Remove useless mini-C library.
Add a new capability, KVM_CAP_S390_CSS_SUPPORT, which will pass
intercepts for channel I/O instructions to userspace. Only I/O
instructions interacting with I/O interrupts need to be handled
in-kernel:
- TEST PENDING INTERRUPTION (tpi) dequeues and stores pending
interrupts entirely in-kernel.
- TEST SUBCHANNEL (tsch) dequeues pending interrupts in-kernel
and exits via KVM_EXIT_S390_TSCH to userspace for subchannel-
related processing.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add support for injecting machine checks (only repressible
conditions for now).
This is a bit more involved than I/O interrupts, for these reasons:
- Machine checks come in both floating and cpu varieties.
- We don't have a bit for machine checks enabling, but have to use
a roundabout approach with trapping PSW changing instructions and
watching for opened machine checks.
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add support for handling I/O interrupts (standard, subchannel-related
ones and rudimentary adapter interrupts).
The subchannel-identifying parameters are encoded into the interrupt
type.
I/O interrupts are floating, so they can't be injected on a specific
vcpu.
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Move the cgroup_event_listener.c tool from Documentation into the new
tools/cgroup directory.
This change involves wiring cgroup_event_listener.c into the tools/
make system so that is can be built with:
$ make tools/cgroup
Signed-off-by: Greg Thelen <gthelen@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some semicolons were left out in the examples.
The #dma-channels and #dma-requests properties have a prefix
that is, by convention, reserved for cell size properties.
Rename those properties to dma-channels and dma-requests.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This is based upon the work by Benoit Cousson [1] and Nicolas Ferre [2]
to add some basic helpers to retrieve a DMA controller device_node and the
DMA request/channel information.
Aim of DMA helpers
- The purpose of device-tree is to describe the capabilites of the hardware.
Thinking about DMA controllers purely from the context of the hardware to
begin with, we can describe a device in terms of a DMA controller as
follows ...
1. Number of DMA controllers
2. Number of channels (maybe physical or logical)
3. Mapping of DMA requests signals to DMA controller
4. Number of DMA interrupts
5. Mapping of DMA interrupts to channels
- With the above in mind the aim of the DT DMA helper functions is to extract
the above information from the DT and provide to the appropriate driver.
However, due to the vast number of DMA controllers and not all are using a
common driver (such as DMA Engine) it has been seen that this is not a
trivial task. In previous discussions on this topic the following concerns
have been raised ...
1. How does the binding support devices with multiple DMA controllers?
2. How to support both legacy DMA controllers not using DMA Engine as
well as those that support DMA Engine.
3. When using with DMA Engine how do we support the various
implementations where the opaque filter function parameter differs
between implementations?
4. How do we handle DMA channels that are identified with a string
versus a integer?
- Hence the design of the DMA helpers has to accomodate the above or align on
an agreement what can be or should be supported.
Design of DMA helpers
1. Registering DMA controllers
In the case of DMA controllers that are using DMA Engine, requesting a
channel is performed by calling the following function.
struct dma_chan *dma_request_channel(dma_cap_mask_t mask,
dma_filter_fn filter_fn,
void *filter_param);
The mask variable is used to match a type of the device controller in a list
of controllers. The filter_fn and filter_param are used to identify the
required dma channel and return a handle to the dma channel of type dma_chan.
From the examples I have seen, the mask and filter_fn are constant
for a given DMA controller and therefore, we can specify these as controller
specific data when registering the DMA controller with the device-tree DMA
helpers.
The filter_param variable is of an unknown type and is typically specific
to the DMA engine implementation for a given DMA controller. To allow some
flexibility in the type and formating of this filter_param we employ an
xlate to translate the device-tree binding information into the appropriate
format. The xlate function used for a DMA controller can also be specified
when registering the DMA controller with the device-tree DMA helpers.
Based upon the above, a function for registering the DMA controller with the
DMA helpers now looks like the below. The data variable is used to pass a
pointer to DMA controller specific data used by the xlate function.
int of_dma_controller_register(struct device_node *np,
struct dma_chan *(*of_dma_xlate)
(struct of_phandle_args *, struct of_dma *),
void *data)
For example, in the case where DMA engine is used, we define the following
structure (that stores the DMA engine capability mask and filter function)
and pass this to the data variable in the above function.
struct of_dma_filter_info {
dma_cap_mask_t dma_cap;
dma_filter_fn filter_fn;
};
2. Representing and requesting channel information
Please see the dma binding documentation included in this patch for a
description of how DMA controllers and client information should be
represented with device-tree. For more information on how this binding
came about please see [3]. In addition to this, feedback received from
the Linux kernel summit showed a consensus (among those who attended) to
use a name to identify DMA client information [4].
A DMA channel can be requested by calling the following function, where name
is a required parameter used for identifying a DMA channel. This function
has been designed to return a structure of type dma_chan to work with the
DMA engine driver. Note that if DMA engine is used then drivers should be
using the DMA engine API dma_request_slave_channel() (implemented in part 2
of this series, "dmaengine: add helper function to request a slave DMA
channel") which will in turn call the below function if device-tree is
present. The aim being to have a common DMA engine interface regardless of
whether device tree is being used.
struct dma_chan *of_dma_request_slave_channel(struct device_node *np,
char *name)
3. Supporting legacy devices not using DMA Engine
These devices present a problem, as there may not be a uniform way to easily
support them with regard to device tree. Ideally, these should be migrated
to DMA engine. However, if this is not possible, then they should still be
able to use this binding, the only constaint imposed by this implementation
is that when requesting a DMA channel via of_dma_request_slave_channel(), it
will return a type of dma_chan.
This implementation has been tested on OMAP4430 using the kernel v3.6-rc5. I
have validated that MMC is working on the PANDA board with this implementation.
My development branch for testing on OMAP can be found here [5].
v6: - minor corrections in DMA binding documentation
v5: - minor update to binding documentation
- added loop to exhaustively search for a slave channel in the case where
there could be alternative channels available
v4: - revert the removal of xlate function from v3
- update the proposed binding format and APIs based upon discussions [3]
v3: - avoid passing an xlate function and instead pass DMA engine parameters
- define number of dma channels and requests in dma-controller node
v2: - remove of_dma_to_resource API
- make property #dma-cells required (no fallback anymore)
- another check in of_dma_xlate_onenumbercell() function
[1] http://article.gmane.org/gmane.linux.drivers.devicetree/12022
[2] http://article.gmane.org/gmane.linux.ports.arm.omap/73622
[3] http://marc.info/?l=linux-omap&m=133582085008539&w=2
[4] http://pad.linaro.org/arm-mini-summit-2012
[5] https://github.com/jonhunter/linux/tree/dev-dt-dma
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <djbw@fb.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Some devices, Buffalo Linkstation LS-XHL and LS-CHLv2 for example,
power-off by restarting to letting u-boot hold the SoC until the user
presses a key. Add a generic driver to implement this. It binds a function
to pm_power_off, which calls arm_pm_restart.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
The QNAP NAS boxes have a microcontroller attached to the SoCs second
serial port. By sending it a simple command, it will turn the power for
the board off. This driver registers a function for pm_power_off to send
such a command.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Improve the documentation to clarify level vs edge triggered power off.
Improve the comments for level vs edge triggered power off.
Make use of gpio_is_valid().
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
It has been over 3 years since the V4L2_CID_[HV]CENTER were deprecated.
Clean up the DocBook and remove the V4L2_CID_VCENTER_DEPRECATED,
V4L2_CID_VCENTER_DEPRECATED control related paragraphs.
Remove the V4L2_CID_[HV]CENTER controls definitions from v4l2-controls.h,
these controls are not used by any driver in the mainline now.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the PM core disables runtime PM for all devices right
after executing subsystem/driver .suspend() callbacks for them
and re-enables it right before executing subsystem/driver .resume()
callbacks for them. This may lead to problems when there are
two devices such that the .suspend() callback executed for one of
them depends on runtime PM working for the other. In that case,
if runtime PM has already been disabled for the second device,
the first one's .suspend() won't work correctly (and analogously
for resume).
To make those issues go away, make the PM core disable runtime PM
for devices right before executing subsystem/driver .suspend_late()
callbacks for them and enable runtime PM for them right after
executing subsystem/driver .resume_early() callbacks for them. This
way the potential conflitcs between .suspend_late()/.resume_early()
and their runtime PM counterparts are still prevented from happening,
but the subtle ordering issues related to disabling/enabling runtime
PM for devices during system suspend/resume are much easier to avoid.
Reported-and-tested-by: Jan-Matthias Braun <jan_braun@gmx.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: 3.4+ <stable@vger.kernel.org>
Sometimes platform/bridge drivers need to be notified when a control from
a sub-device changes value. In order to support this a notify callback was
added.
[dheitmueller@kernellabs.com: fix merge conflict in v4l2-ctrls.c]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
