Pull LED subsystem updates from Bryan Wu:
"In this cycle, we finished to merge patches for LED Flash class
driver.
Other than that we have some bug fixes and new drivers for LED
controllers"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (33 commits)
leds:lp55xx: fix firmware loading error
leds: fix max77693-led build errors
leds: fix aat1290 build errors
leds: aat1290: pass flags parameter to devm_gpiod_get
leds: ktd2692: pass flags parameter to devm_gpiod_get
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
leds: aat1290: add support for V4L2 Flash sub-device
DT: aat1290: Document handling external strobe sources
leds: max77693: add support for V4L2 Flash sub-device
media: Add registration helpers for V4L2 flash sub-devices
v4l: async: Add a pointer to of_node to struct v4l2_subdev, match it
Documentation: leds: Add description of v4l2-flash sub-device
leds: add BCM6358 LED driver
leds: add DT binding for BCM6358 LED controller
leds: fix brightness changing when software blinking is active
Documentation: leds-lp5523: describe master fader attributes
leds: lp5523: add master_fader support
leds: leds-gpio: Allow compile test if !GPIOLIB
leds: leds-gpio: Add missing #include <linux/of.h>
gpiolib: Add missing dummies for the unified device properties interface
...
LP55xx driver uses not firmware file but raw data to load program through
the firmware interface.(Documents/leds/leds-lp55xx.txt)
For example, here is how to run blinking green channel pattern.
(The second engine is seleted and MUX is mapped to 'RGB' mode)
echo 2 > /sys/bus/i2c/devices/xxxx/select_engine
echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux
echo 1 > /sys/class/firmware/lp5562/loading
echo "4000600040FF6000" > /sys/class/firmware/lp5562/data
echo 0 > /sys/class/firmware/lp5562/loading
echo 1 > /sys/bus/i2c/devices/xxxx/run_engine
However, '/sys/class/firmware/<device name>' is not created after the
firmware loader user helper was introduced.
This feature is used in the case below.
As soon as the firmware download is requested by the driver, firmware
class subsystem tries to find the binary file.
If it gets failed, then it just falls back to user helper to load
raw data manually. Here, you can see the device file under
/sys/class/firmware/.
To make it happen, LP55xx driver requires two configurations.
1. Enable CONFIG_FW_LOADER_USER_HELPER_FALLBACK in Kconfig
2. Set option, 'FW_OPT_USERHELPER' on requesting the firmware data.
It means the second option should be 'false' in
request_firmware_nowait().
This option enables to load firmware data manually by calling
fw_load_from_user_helper().
Cc: linux-leds@vger.kernel.org
Signed-off-by: Milo Kim <milo.kim@ti.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fix build errors when LEDS_MAX77693=y and V4L2_FLASH_LED_CLASS=m
by restricting LEDS_MAX77693 to =m if V4L2_FLASH_LED_CLASS=m.
drivers/leds/leds-max77693.c:1062: undefined reference to `v4l2_flash_release'
drivers/leds/leds-max77693.c:1068: undefined reference to `v4l2_flash_release'
drivers/built-in.o: In function `max77693_register_led':
drivers/leds/leds-max77693.c:968: undefined reference to `v4l2_flash_init'
drivers/built-in.o: In function `max77693_led_probe':
drivers/leds/leds-max77693.c:1048: undefined reference to `v4l2_flash_release'
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Fix build errors when LEDS_AAT1290=y and V4L2_FLASH_LED_CLASS=m
by restricting LEDS_AAT1290 to =m if V4L2_FLASH_LED_CLASS=m.
drivers/built-in.o: In function `aat1290_led_remove':
leds-aat1290.c:(.text+0xe5d77): undefined reference to `v4l2_flash_release'
drivers/built-in.o: In function `aat1290_led_probe':
leds-aat1290.c:(.text+0xe6494): undefined reference to `v4l2_flash_init'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"Thanks to Samuel Thibault input device (keyboard) LEDs are no longer
hardwired within the input core but use LED subsystem and so allow use
of different triggers; Hans de Goede did a large update for the ALPS
touchpad driver; we have new TI drv2665 haptics driver and DA9063
OnKey driver, and host of other drivers got various fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: pixcir_i2c_ts - fix receive error
MAINTAINERS: remove non existent input mt git tree
Input: improve usage of gpiod API
tty/vt/keyboard: define LED triggers for VT keyboard lock states
tty/vt/keyboard: define LED triggers for VT LED states
Input: export LEDs as class devices in sysfs
Input: cyttsp4 - use swap() in cyttsp4_get_touch()
Input: goodix - do not explicitly set evbits in input device
Input: goodix - export id and version read from device
Input: goodix - fix variable length array warning
Input: goodix - fix alignment issues
Input: add OnKey driver for DA9063 MFD part
Input: elan_i2c - add product IDs FW names
Input: elan_i2c - add support for multi IC type and iap format
Input: focaltech - report finger width to userspace
tty: remove platform_sysrq_reset_seq
Input: synaptics_i2c - use proper boolean values
Input: psmouse - use true instead of 1 for boolean values
Input: cyapa - fix a few typos in comments
Input: stmpe-ts - enforce device tree only mode
...
Add support for V4L2 Flash sub-device to the aat1290 LED Flash class
driver. The support allows for V4L2 Flash sub-device to take the control
of the LED Flash class device.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This change creates a new input handler called "leds" that exports LEDs on input
devices as standard LED class devices in sysfs and allows controlling their
state via sysfs or via any of the standard LED triggers. This allows to
re-purpose and reassign LDEs on the keyboards to represent states other
than the standard keyboard states (CapsLock, NumLock, etc).
The old API of controlling input LEDs by writing into /dev/input/eventX
devices is still present and will take precedence over accessing via LEDs
subsystem (i.e. it may override state set by a trigger). If input device is
"grabbed" then requests coming through LED subsystem will be ignored.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the LED controller on Broadcom's BCM6358.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency of LEDS_GPIO on GPIOLIB if COMPILE_TEST is
enabled.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds a driver to support the ktd2692 flash LEDs.
ktd2692 can control flash current by ExpressWire interface.
Signed-off-by: Ingi Kim <ingi2.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This adds support for the LED controller on Broadcom's BCM6328.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds a driver for the 1.5A Step-Up Current Regulator
for Flash LEDs. The device is programmed through a Skyworks proprietary
AS2Cwire serial digital interface.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds led-flash support to Maxim max77693 chipset.
A device can be exposed to user space through LED subsystem
sysfs interface. Device supports up to two leds which can
work in flash and torch mode. The leds can be triggered
externally or by software.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The TLC59116 is an I2C bus controlled 16-channel LED driver. The
TLC59108 is an I2C bus controlled 8-channel LED driver, which is very
similar to the TLC59116. Each LED output has its own 8-bit
fixed-frequency PWM controller to control the brightness of the LED.
The LEDs can also be fixed off and on, making them suitable for use as
GPOs.
This is based on a driver from Belkin, but has been extensively
rewritten and extended to support both 08 and 16 versions.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Imre Kaloz <kaloz@openwrt.org>
Cc: Matthew.Fatheree@belkin.com
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This adds support for the WLED ('White' LED) block on Qualcomm's
PM8941 PMICs.
(cooloney@gmail.com: remove unneeded semicolon)
Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Some LED devices support two operation modes - torch and flash.
This patch provides support for flash LED devices in the LED subsystem
by introducing new sysfs attributes and kernel internal interface.
The attributes being introduced are: flash_brightness, flash_strobe,
flash_timeout, max_flash_timeout, max_flash_brightness, flash_fault,
flash_sync_strobe and available_sync_leds. All the flash related
features are placed in a separate module.
The modifications aim to be compatible with V4L2 framework requirements
related to the flash devices management. The design assumes that V4L2
sub-device can take of the LED class device control and communicate
with it through the kernel internal interface. When V4L2 Flash sub-device
file is opened, the LED class device sysfs interface is made
unavailable.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The driver should select REGMAP_I2C rather than depend on it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Introduce the Texas Instruments lp8860
4 channel LED driver.
This driver configures the device in display cluster mode
as this seems to be the most used configuration at the
time of the driver configuration.
For more product information please see the link below:
http://www.ti.com/product/lp8860-q1
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
Register ntc_thermistor driver with thermal subsystem.
Add support for F15h M60h to k10temp driver.
Add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vI5p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for menf21bmc.
- convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
- register ntc_thermistor driver with thermal subsystem.
- add support for F15h M60h to k10temp driver.
- add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18
* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
MAINTAINERS: add entry for the PWM fan driver
hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (k10temp) Add support for F15h M60h
hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
hwmon: (ads1015) Use of_property_read_u32 at appropriate places
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into drivers
directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=POJD
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
Most of the new code is for the Keystone Navigator driver, which is
new base support that is going to be needed for their hardware
accelerated network driver and other units.
Most of the commits are for moving old code around from at91 and omap
for things that are done in device drivers nowadays.
- at91: move reset, poweroff, memory and clocksource code into
drivers directories
- socfpga: add edac driver (through arm-soc, as requested by Boris)
- omap: move omap-intc code to drivers/irqchip
- sunxi: added an RTC driver for sun6i
- omap: mailbox driver related changes
- keystone: support for the "Navigator" component
- versatile: new reboot, led and soc drivers"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
bus: arm-ccn: Fix spurious warning message
leds: add device tree bindings for register bit LEDs
soc: add driver for the ARM RealView
power: reset: driver for the Versatile syscon reboot
leds: add a driver for syscon-based LEDs
drivers/soc: ti: fix build break with modules
MAINTAINERS: Add Keystone Multicore Navigator drivers entry
soc: ti: add Keystone Navigator DMA support
Documentation: dt: soc: add Keystone Navigator DMA bindings
soc: ti: add Keystone Navigator QMSS driver
Documentation: dt: soc: add Keystone Navigator QMSS bindings
rtc: sunxi: Depend on platforms sun4i/sun7i that actually have the rtc
rtc: sun6i: Add sun6i RTC driver
irqchip: omap-intc: remove unnecessary comments
irqchip: omap-intc: correct maximum number or MIR registers
irqchip: omap-intc: enable TURBO idle mode
irqchip: omap-intc: enable IP protection
irqchip: omap-intc: remove unnecesary of_address_to_resource() call
irqchip: omap-intc: comment style cleanup
irqchip: omap-intc: minor improvement to omap_irq_pending()
...
This makes it possible to create a set of LEDs from a syscon
MFD instance, which is lean mean and clean on the ARM
reference designs and can replace the Versatile LEDs driver
in the long run, as well as other custom syscon LEDs drivers.
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
[Fixed cocinelle warnings]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Added driver to support the 14F021P00 BMC LEDs.
The BMC is a Board Management Controller including four LEDs which
can be switched on and off.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Use MACH_KIRKWOOD which will be set when kirkwood is built as part of
mach-mvebu.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Link: https://lkml.kernel.org/r/1409417172-6846-5-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A handful of driver-related changes. We've had a bunch of them going in through
other branches as well, so it's only a part of what we really have this release.
Larger pieces are:
* Removal of a now unused PWM driver for atmel
- This includes AVR32 changes that have been appropriately acked.
* Performance counter support for the arm CCN interconnect
* OMAP mailbox driver cleanups and consolidation
* PCI and SATA PHY drivers for SPEAr 13xx platforms
* Redefinition (with backwards compatibility!) of PCI DT bindings for Tegra to
better model regulators/power.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=fsP6
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"A handful of driver-related changes. We've had a bunch of them going
in through other branches as well, so it's only a part of what we
really have this release.
Larger pieces are:
- Removal of a now unused PWM driver for atmel
[ This includes AVR32 changes that have been appropriately acked ]
- Performance counter support for the arm CCN interconnect
- OMAP mailbox driver cleanups and consolidation
- PCI and SATA PHY drivers for SPEAr 13xx platforms
- Redefinition (with backwards compatibility!) of PCI DT bindings for
Tegra to better model regulators/power"
Note: this merge also fixes up the semantic conflict with the new
calling convention for devm_phy_create(), see commit f0ed817638 ("phy:
core: Let node ptr of PHY point to PHY and not of PHY provider") that
came in through Greg's USB tree.
Semantic merge patch by Stephen Rothwell <sfr@canb.auug.org.au> through
the next tree.
* tag 'drivers-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: arm-ccn: Fix error handling at event allocation
mailbox/omap: add a parent structure for every IP instance
mailbox/omap: remove the private mailbox structure
mailbox/omap: consolidate OMAP mailbox driver
mailbox/omap: simplify the fifo assignment by using macros
mailbox/omap: remove omap_mbox_type_t from mailbox ops
mailbox/omap: remove OMAP1 mailbox driver
mailbox/omap: use devm_* interfaces
bus: ARM CCN: add PERF_EVENTS dependency
bus: ARM CCN PMU driver
PCI: spear: Remove spear13xx_pcie_remove()
PCI: spear: Fix Section mismatch compilation warning for probe()
ARM: tegra: Remove legacy PCIe power supply properties
PCI: tegra: Remove deprecated power supply properties
PCI: tegra: Implement accurate power supply scheme
ARM: SPEAr13xx: Update defconfigs
ARM: SPEAr13xx: Add pcie and miphy DT nodes
ARM: SPEAr13xx: Add bindings and dt node for misc block
ARM: SPEAr13xx: Fix static mapping table
phy: Add drivers for PCIe and SATA phy on SPEAr13xx
...
This adds a driver for the iPAQ microcontroller LED.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The leds-atmel-pwm driver is now obsolete. It is not used by any mainlined
boards and is replaced by the generic leds_pwm with the pwm-atmel driver using
the generic PWM framework.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull LED updates from Bryan Wu:
"I just found merge window is open and I'm quite busy and almost forget
to send out this pull request. Thanks Russell and Alexandre ping me
about this.
So basically we got some clean up and leds-pwm fixing patches from
Russell"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Remove duplicated OOM message for individual driver
drivers/leds: Replace __get_cpu_var use through this_cpu_ptr
leds: lp55xx: add DT bindings for LP55231
leds: 88pm860x: Fix missing refcount decrement for parent of_node
leds: 88pm860x: Use of_get_child_by_name
leds: leds-pwm: add DT support for LEDs wired to supply
leds: leds-pwm: implement PWM inversion
leds: leds-pwm: convert OF parsing code to use led_pwm_add()
leds: leds-pwm: provide a common function to setup a single led-pwm device
leds: pca9685: Remove leds-pca9685 driver
dell-led: add mic mute led interface
Pull HID patches from Jiri Kosina:
- RMI driver for Synaptics touchpads, by Benjamin Tissoires, Andrew
Duggan and Jiri Kosina
- cleanup of hid-sony driver and improved support for Sixaxis and
Dualshock 4, by Frank Praznik
- other usual small fixes and support for new device IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (29 commits)
HID: thingm: thingm_fwinfo[] doesn't need to be global
HID: core: add two new usages for digitizer
HID: hid-sensor-hub: new device id and quirk for STM Sensor hub
HID: usbhid: enable NO_INIT_REPORTS quirk for Semico USB Keykoard
HID: hid-sensor-hub: Set report quirk for Microsoft Surface
HID: debug: add labels for HID Sensor Usages
HID: uhid: Use kmemdup instead of kmalloc + memcpy
HID: rmi: do not handle touchscreens through hid-rmi
HID: quirk for Saitek RAT7 and MMO7 mices' mode button
HID: core: fix validation of report id 0
HID: rmi: fix masks for x and w_x data
HID: rmi: fix wrong struct field name
HID: rmi: do not fetch more than 16 bytes in a query
HID: rmi: check for the existence of some optional queries before reading query 12
HID: i2c-hid: hid report descriptor retrieval changes
HID: add missing hid usages
HID: hid-sony - allow 3rd party INTEC controller to turn off all leds
HID: sony: Add blink support to the Sixaxis and DualShock 4 LEDs
HID: sony: Initialize the controller LEDs with a device ID value
HID: sony: Use the controller Bluetooth MAC address as the unique value in the battery name string
...
I got a build error today, since LEDS_VERSATILE can be built-in while LEDS_CLASS
is a module:
drivers/built-in.o: In function `versatile_leds_probe':
:(.text+0x155020): undefined reference to `led_classdev_register'
I suggest we turn this option into 'tristate' so that the dependency
tracking works correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver is replaced by pwm-pca9685 driver and there is no user uses this
driver in current tree. So remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Acked-by: Maximilian Güntner <maximilian.guentner@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch refactors the way the thingm driver registers a blink(1) LED.
In order to make the driver simpler and more standard, drop the "rgb"
sysfs attribute and create one instance of LED class per RGB channel.
Actually, the name of the LED class instance registered for a blink(1)
device is "blink1::ABCD", where ABCD is the last 4 chars of the serial
number. The driver now registers 3 instances per RGB chip, named
"thingmX:{red,green,blue}:ledY" where X is the hidraw minor number and Y
is the RGB chip number (as seen by the firmware).
This patch also uses work queues to defer calls with the device, which
now allows triggers to work as expected with this LED device.
Also remove the brightness structure field and the brightness_get
backend, as it is already handled by the LED class, and changes the
prefix of functions and structures to thingm_ to match the driver name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Pull LED updates from Bryan Wu:
"This cycle we got:
- new driver for leds-mc13783
- bug fixes
- code cleanup"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: make sure we unregister a trigger only once
leds: leds-pwm: properly clean up after probe failure
leds: clevo-mail: Make probe function __init
leds-ot200: Fix dependencies
leds-gpio: of: introduce MODULE_DEVICE_TABLE for module autoloading
leds: clevo-mail: remove __initdata marker
leds: leds-ss4200: remove __initdata marker
leds: blinkm: remove unnecessary spaces
leds: lp5562: remove unnecessary parentheses
leds: leds-ss4200: remove DEFINE_PCI_DEVICE_TABLE macro
leds: leds-s3c24xx: Trivial cleanup in header file
drivers/leds: delete non-required instances of include <linux/init.h>
leds: leds-gpio: add retain-state-suspended property
leds: leds-mc13783: Add devicetree support
leds: leds-mc13783: Remove unnecessary cleaning of registers on exit
leds: leds-mc13783: Use proper "max_brightness" value fo LEDs
leds: leds-mc13783: Use LED core PM functions
leds: leds-mc13783: Add MC34708 LED support
leds: Turn off led if blinking is disabled
ledtrig-cpu: Handle CPU hot(un)plugging
Now that we have converted this driver to a real platform device
module-based thing, we move the driver down into the LEDs
subsystem and rename the config option to LEDS_VERSATILE.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Pawel Moll <pawel.moll@arm.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Bachmann OT200 is a Geode-based device, so OT200-specific drivers
are only useful on X86_32, except for build testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
With the move of kirkwood into mach-mvebu, drivers Kconfig need
tweeking to allow the kirkwood specific drivers to be built.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The NXP PCA9685 supports 16 channels/leds using a 12-bit PWM (4095
levels of brightness)
This driver supports configuration using platform_data.
Signed-off-by: Maximilian Güntner <maximilian.guentner@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Pull led updates from Bryan Wu:
"Sorry for the late pull request, since I'm just back from vacation.
LED subsystem updates for 3.12:
- pca9633 driver DT supporting and pca9634 chip supporting
- restore legacy device attributes for lp5521
- other fixing and updates"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (28 commits)
leds: wm831x-status: Request a REG resource
leds: trigger: ledtrig-backlight: Fix invalid memory access in fb_event notification callback
leds-pca963x: Fix device tree parsing
leds-pca9633: Rename to leds-pca963x
leds-pca9633: Add mutex to the ledout register
leds-pca9633: Unique naming of the LEDs
leds-pca9633: Add support for PCA9634
leds: lp5562: use LP55xx common macros for device attributes
Documentation: leds-lp5521,lp5523: update device attribute information
leds: lp5523: remove unnecessary writing commands
leds: lp5523: restore legacy device attributes
leds: lp5523: LED MUX configuration on initializing
leds: lp5523: make separate API for loading engine
leds: lp5521: remove unnecessary writing commands
leds: lp5521: restore legacy device attributes
leds: lp55xx: add common macros for device attributes
leds: lp55xx: add common data structure for program
Documentation: leds: Fix a typo
leds: ss4200: Fix incorrect placement of __initdata
leds: clevo-mail: Fix incorrect placement of __initdata
...
The driver now supports the chips pca9633 and pca9634, therefore we
rename the files to more generic and meaningul names
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add support for PCA9634 chip, which belongs to the same family as the
9633 but with support for 8 outputs instead of 4.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
With the DT conversion, the board Kconfig symbols MACH_ are going to be
removed. In order to prepare this removal, this patch replaces alls the
machines dependencies for leds-netxbig by ARCH_KIRKWOOD.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
With the DT conversion, the board Kconfig symbols MACH_ are going to be
removed. In order to prepare this removal, this patch replaces alls the
machines dependencies for leds-ns2 by ARCH_KIRKWOOD.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
LP8501 can drive up to 9 channels like LP5523.
LEDs can be controlled directly via the I2C and programmable engines are
supported.
LP55xx common driver
LP8501 is one of LP55xx family device, so LP55xx common code are used.
Chip specific data is defined in the structure, 'lp55xx_device_config'.
Differences between LP8501 and LP5523
Different register layout for LED output control and others.
LP8501 specific feature for separate output power selection.
LP8501 doesn't support external clock detection.
Different programming engine data.
LP8501 specific feature - output power selection
Output channels are selected by power selection - Vout or Vdd.
Separate power for VDD1-6 and VDD7-9 are available.
It is configurable in the platform data.
To support this feature, LP55xx DT structure and header are changed.
Device tree binding is updated as well.
LED pattern data
Example pattern data is updated in the driver documentation.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
The driver is superseded by the generic pwm-renesas-tpu driver used with
leds-pwm.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Bryan Wu <cooloney@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
For better driver management, new subdirectory, 'trigger' is created.
All LED trigger drivers are moved into this directory.
Internal header, 'leds.h' is included in each LED trigger drivers.
Fix the location of header file, "leds.h" -> "../leds.h" in driver files.
One exception is here, 'ledtrig-timer.c'.
There is no need to include 'leds.h'. so '#include "leds.h"' line was removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
