Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
Finally(!), make Linux support being an I2C slave. Most of the existing
infrastructure is reused. We mainly add i2c_slave_register/unregister()
calls which tells i2c bus drivers to activate the slave mode. Then, they
also get a callback to report slave events to.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fix speeling typo found in html files within
Documentation/DocBook/device-drivers.
It is because html files are generated from comments in source,
so I have to fix comments in the source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Commit 5d98e61d33 ("I2C/ACPI: Add i2c ACPI operation region support")
renamed the i2c-core module. This may cause regressions for
distributions, so put the ACPI code back into the core.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Lan Tianyu <tianyu.lan@intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Commit da3c6647(I2C/ACPI: Clean up I2C ACPI code and Add CONFIG_I2C_ACPI
config) adds a new kernel config I2C_ACPI and make I2C core built in
when the config is selected. This is wrong because distributions
etc generally compile I2C as a module and the commit broken that.
This patch is to rename I2C_ACPI to ACPI_I2C_OPREGION. New config
only controls ACPI I2C operation region code and depends on I2C=y.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: removed unrelated change for Kconfig]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clean up ACPI related code in the i2c core and add CONFIG_I2C_ACPI
to enable I2C ACPI code.
Current there is a race between removing I2C ACPI operation region
and ACPI AML code accessing. So make i2c core built-in if CONFIG_I2C_ACPI
is set.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5.0 spec(5.5.2.4.5) defines GenericSerialBus(i2c, spi, uart) operation region.
It allows ACPI aml code able to access such kind of devices to implement
some ACPI standard method.
ACPI Spec defines some access attribute to associate with i2c protocol.
AttribQuick Read/Write Quick Protocol
AttribSendReceive Send/Receive Byte Protocol
AttribByte Read/Write Byte Protocol
AttribWord Read/Write Word Protocol
AttribBlock Read/Write Block Protocol
AttribBytes Read/Write N-Bytes Protocol
AttribProcessCall Process Call Protocol
AttribBlockProcessCall Write Block-Read Block Process Call Protocol
AttribRawBytes Raw Read/Write N-BytesProtocol
AttribRawProcessBytes Raw Process Call Protocol
On the Asus T100TA, Bios use GenericSerialBus operation region to access
i2c device to get battery info.
Sample code From Asus T100TA
Scope (_SB.I2C1)
{
Name (UMPC, ResourceTemplate ()
{
I2cSerialBus (0x0066, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.I2C1",
0x00, ResourceConsumer, ,
)
})
...
OperationRegion (DVUM, GenericSerialBus, Zero, 0x0100)
Field (DVUM, BufferAcc, NoLock, Preserve)
{
Connection (UMPC),
Offset (0x81),
AccessAs (BufferAcc, AttribBytes (0x3E)),
FGC0, 8
}
...
}
Device (BATC)
{
Name (_HID, EisaId ("PNP0C0A")) // _HID: Hardware ID
Name (_UID, One) // _UID: Unique ID
...
Method (_BST, 0, NotSerialized) // _BST: Battery Status
{
If (LEqual (AVBL, One))
{
Store (FGC0, BFFG)
If (LNotEqual (STAT, One))
{
ShiftRight (CHST, 0x04, Local0)
And (Local0, 0x03, Local0)
If (LOr (LEqual (Local0, One), LEqual (Local0, 0x02)))
{
Store (0x02, Local1)
}
...
}
The i2c operation region is defined under I2C1 scope. _BST method under
battery device BATC read battery status from the field "FCG0". The request
would be sent to i2c operation region handler.
This patch is to add i2c ACPI operation region support. Due to there are
only "Byte" and "Bytes" protocol access on the Asus T100TA, other protocols
have not been tested.
About RawBytes and RawProcessBytes protocol, they needs specific drivers to interpret
reference data from AML code according ACPI 5.0 SPEC(5.5.2.4.5.3.9 and 5.5.2.4.5.3.10).
So far, not found such case and will add when find real case.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Class based instantiation can cause noticeable delays when booting. This
mechanism is used when it is not possible to describe slaves on I2C
busses. As we do have other mechanisms, most embedded I2C will not need
classes and for embedded it is explicitly not recommended to use them. Add
a deprecation warning for drivers which want to disable class based
instantiation in the near future to gain boot-up time, so users relying
on this technique can switch to something better. They really should.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add some kerneldoc style documentaton to the i2c_algorithm
structure, and point the master_xfer return codes at the
right place in Documentation/i2c/fault_codes
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The body of i2c_parent_is_i2c_adapter() is currently guarded by
I2C_MUX. It should be CONFIG_I2C_MUX instead.
Among potentially other problems, this resulted in i2c_lock_adapter()
only locking I2C mux child adapters, and not the parent adapter. In
turn, this could allow inter-mingling of mux child selection and I2C
transactions, which could result in I2C transactions being directed to
the wrong I2C bus, and possibly even switching between busses in the
middle of a transaction.
One concrete issue caused by this bug was corrupted HDMI EDID reads
during boot on the NVIDIA Tegra Seaboard system, although this only
became apparent in recent linux-next, when the boot timing was changed
just enough to trigger the race condition.
Fixes: 3923172b3d ("i2c: reduce parent checking to a NOOP in non-I2C_MUX case")
Cc: Phil Carmody <phil.carmody@partner.samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The 'driver' field of the i2c_client struct is redundant. The same data can be
accessed through to_i2c_driver(client->dev.driver). The generated code for both
approaches in more or less the same.
E.g. on ARM the expression client->driver->command(...) generates
...
ldr r3, [r0, #28]
ldr r3, [r3, #32]
blx r3
...
and the expression to_i2c_driver(client->dev.driver)->command(...) generates
...
ldr r3, [r0, #160]
ldr r3, [r3, #-4]
blx r3
...
Other architectures will generate similar code.
All users of the 'driver' field outside of the I2C core have already been
converted. So this only leaves the core itself. This patch converts the
remaining few users in the I2C core and then removes the 'driver' field from the
i2c_client struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This follows what has already been done for the DeviceTree helpers. Move
the ACPI helpers from drivers/acpi/acpi_i2c.c to the I2C core and update
documentation accordingly.
This also solves a problem reported by Jerry Snitselaar that we can't build
the ACPI I2C helpers as a module.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C of helpers used to live in of_i2c.c but experience (from SPI) shows
that it is much cleaner to have this in the core. This also removes a
circular dependency between the helpers and the core, and so we can
finally register child nodes in the core instead of doing this manually
in each driver. So, fix the drivers and documentation, too.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In 0826374 - i2c: Multiplexed I2C bus core support
core i2c code increased in size and complexity even when I2C_MUX
wasn't selected.
Turning this check into a constant NULL in the n case lets the
client functions in be simplified too, not needing to include
never-called calls to the mux-specific helpers.
Signed-off-by: Phil Carmody <phil.carmody@partner.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_del_adapter() is usually called from a drivers remove callback. The Linux
device driver model does not allow the remove callback to fail and all resources
allocated in the probe callback need to be freed, as well as all resources which
have been provided to the rest of the kernel(for example a I2C adapter) need to
be revoked. So any function revoking such resources isn't allowed to fail
either. i2c_del_adapter() adheres to this requirement and will never fail. But
i2c_del_adapter()'s return type is int, which may cause driver authors to think
that it can fail. This led to code constructs like:
ret = i2c_del_adapter(...);
BUG_ON(ret);
Since i2c_del_adapter() always returns 0 the BUG_ON is never hit and essentially
becomes dead code, which means it can be removed. Making the return type of
i2c_del_adapter() void makes it explicit that the function will never fail and
should prevent constructs like the above from re-appearing in the kernel code.
All callers of i2c_del_adapter() have already been updated in a previous patch
to ignore the return value, so the conversion of the return type from int to
void can be done without causing any build failures.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The detach_adapter callback has been deprecated for quite some time and has no
user left. Keeping it alive blocks other cleanups, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add i2c bus recovery infrastructure to i2c adapters as specified in the i2c
protocol Rev. 03 section 3.1.16 titled "Bus clear".
http://www.nxp.com/documents/user_manual/UM10204.pdf
Sometimes during operation i2c bus hangs and we need to give dummy clocks to
slave device to start the transfer again. Now we may have capability in the bus
controller to generate these clocks or platform may have gpio pins which can be
toggled to generate dummy clocks. This patch supports both.
This patch also adds in generic bus recovery routines gpio or scl line based
which can be used by bus controller. In addition controller driver may provide
its own version of the bus recovery routine.
This doesn't support multi-master recovery for now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[wsa: changed gpio type to int and minor reformatting]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI 5 introduced I2cSerialBus resource that makes it possible to enumerate
and configure the I2C slave devices behind the I2C controller. This patch
adds helper functions to support I2C slave enumeration.
An ACPI enabled I2C controller driver only needs to call acpi_i2c_register_devices()
in order to get its slave devices enumerated, created and bound to the
corresponding ACPI handle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
s/address_data/address_list/ in addition to c3813d6.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull media updates from Mauro Carvalho Chehab:
"This is the first part of the media patches for v3.6.
This patch series contain:
- new DVB frontend: rtl2832
- new video drivers: adv7393
- some unused files got removed
- a selection API cleanup between V4L2 and V4L2 subdev API's
- a major redesign at v4l-ioctl2, in order to clean it up
- several driver fixes and improvements."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (174 commits)
v4l: Export v4l2-common.h in include/linux/Kbuild
media: Revert "[media] Terratec Cinergy S2 USB HD Rev.2"
[media] media: Use pr_info not homegrown pr_reg macro
[media] Terratec Cinergy S2 USB HD Rev.2
[media] v4l: Correct conflicting V4L2 subdev selection API documentation
[media] Feature removal: V4L2 selections API target and flag definitions
[media] v4l: Unify selection flags documentation
[media] v4l: Unify selection flags
[media] v4l: Common documentation for selection targets
[media] v4l: Unify selection targets across V4L2 and V4L2 subdev interfaces
[media] v4l: Remove "_ACTUAL" from subdev selection API target definition names
[media] V4L: Remove "_ACTIVE" from the selection target name definitions
[media] media: dvb-usb: print mac address via native %pM
[media] s5p-tv: Use module_i2c_driver in sii9234_drv.c file
[media] media: gpio-ir-recv: add allowed_protos for platform data
[media] s5p-jpeg: Use module_platform_driver in jpeg-core.c file
[media] saa7134: fix spelling of detach in label
[media] cx88-blackbird: replace ioctl by unlocked_ioctl
[media] cx88: don't use current_norm
[media] cx88: fix a number of v4l2-compliance violations
...
SCCB is a serial communication bus developed by Omnivision. Its 2-wire
mode is very similar to SMBus byte data transactions, but requires the
controller to ignore the ACK bit and to insert a stop condition after
each message.
Add a device SCCB flag and a message stop flag to be passed to
controller drivers.
[JD: Kill rogue definition in go7007 driver.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some drivers (in particular for TV cards) need exclusive access to
their I2C buses for specific operations. Export an unlocked flavor
of i2c_transfer to give them full control.
The unlocked flavor has the following limitations:
* Obviously, caller must hold the i2c adapter lock.
* No debug messages are logged. We don't want to log messages while
holding a rt_mutex.
* No check is done on the existence of adap->algo->master_xfer. It
is thus the caller's responsibility to ensure that the function is
OK to call.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This converts a struct device * to a struct i2c_adapter * while verifying
that the device really is an I2C adapter. Just like i2c_verify_client.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Last piece of code using ANY_I2C_BUS was deleted almost 2 years ago,
so ANY_I2C_BUS can go away as well.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This patch introduces the module_i2c_driver macro which is a convenience macro
for I2C driver modules similar to module_platform_driver. It is intended to be
used by drivers which init/exit section does nothing but register/unregister
the I2C driver. By using this macro it is possible to eliminate a few lines of
boilerplate code per I2C driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The <linux/module.h> pretty much brings in the kitchen sink along
with it, so it should be avoided wherever reasonably possible in
terms of being included from other commonly used <linux/something.h>
files, as it results in a measureable increase on compile times.
The worst culprit was probably device.h since it is used everywhere.
This file also had an implicit dependency/usage of mutex.h which was
masked by module.h, and is also fixed here at the same time.
There are over a dozen other headers that simply declare the
struct instead of pulling in the whole file, so follow their lead
and simply make it a few more.
Most of the implicit dependencies on module.h being present by
these headers pulling it in have been now weeded out, so we can
finally make this change with hopefully minimal breakage.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The original implementations reference THIS_MODULE in an inline.
We could include <linux/export.h>, but it is better to avoid chaining.
Fortunately someone else already thought of this, and made a similar
inline into a #define in <linux/device.h> for device_schedule_callback(),
[see commit 523ded71de] so follow that precedent here.
Also bubble up any __must_check that were used on the prev. wrapper inline
functions up one to the real __register functions, to preserve any prev.
sanity checks that were used in those instances.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reimplemented at least 17 times discounting error mangling cases
where it could be used.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While the JC42-compatible chips are temperature sensors, I2C_CLASS_SPD
makes more sense because these chips always live on memory modules.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
The last legitimate user of i2c_driver.attach_adapter and
.detach_adapter is gone, so we can finally deprecate these callbacks.
The last few drivers which still use these will have to be updated to
make use of standard I2C device instantiation ways instead.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Introduce i2c_for_each_dev(), an i2c device iterator with proper
locking for use by i2c-dev. This is needed so that we can get rid of
the attach_adapter and detach_adapter legacy callback functions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The last remaining ID in <linux/i2c-id.h> is no longer used anywhere,
so we can finally get rid of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename the parameter of i2c_get_adapter() to "nr", to make it clear we
are passing an adapter number and not an adapter ID (which have gone
away by now.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks. Drop the
conditionals and remove the #ifdef blocks from the affected drivers.
Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
It's about time to make it clear that i2c_adapter.id is deprecated.
Hopefully this will remind the last user to move over to a different
strategy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Only i2c devices can have their type set to i2c_adapter_type, so
testing the bus type is redundant.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Add multiplexed bus core support. I2C multiplexer and switches
like pca954x get instantiated as new adapters per port.
Signed-off-by: Michael Lawnick <ml.lawnick@gmx.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Moving userspace-instantiated clients to separate lists wasn't nearly
enough to avoid deadlocks in multiplexed bus cases. We also want to
have a dedicated mutex to protect each list.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Uninline i2c adapter locking helper functions, move them to i2c-core,
and use them in i2c-core itself. The functions are still exported for
external users. This makes future updates to the locking model (which
will be needed for multiplexing support) possible and transparent.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Now that i2c-core offers the possibility to provide custom probing
function for I2C devices, let's make use of it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix kernel-doc warnings in linux/i2c.h:
Warning(include/linux/i2c.h:176): No description found for parameter 'alert'
Warning(include/linux/i2c.h:259): No description found for parameter 'of_node'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
