When checking a new device's descriptors, the USB core does not check
for duplicate endpoint addresses. This can cause a problem when the
sysfs files for those endpoints are created; trying to create multiple
files with the same name will provoke a WARNING:
WARNING: CPU: 2 PID: 865 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x8a/0xa0
sysfs: cannot create duplicate filename
'/devices/platform/dummy_hcd.0/usb2/2-1/2-1:64.0/ep_05'
Kernel panic - not syncing: panic_on_warn set ...
CPU: 2 PID: 865 Comm: kworker/2:1 Not tainted 4.9.0-rc7+ #34
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Workqueue: usb_hub_wq hub_event
ffff88006bee64c8 ffffffff81f96b8a ffffffff00000001 1ffff1000d7dcc2c
ffffed000d7dcc24 0000000000000001 0000000041b58ab3 ffffffff8598b510
ffffffff81f968f8 ffffffff850fee20 ffffffff85cff020 dffffc0000000000
Call Trace:
[< inline >] __dump_stack lib/dump_stack.c:15
[<ffffffff81f96b8a>] dump_stack+0x292/0x398 lib/dump_stack.c:51
[<ffffffff8168c88e>] panic+0x1cb/0x3a9 kernel/panic.c:179
[<ffffffff812b80b4>] __warn+0x1c4/0x1e0 kernel/panic.c:542
[<ffffffff812b8195>] warn_slowpath_fmt+0xc5/0x110 kernel/panic.c:565
[<ffffffff819e70ca>] sysfs_warn_dup+0x8a/0xa0 fs/sysfs/dir.c:30
[<ffffffff819e7308>] sysfs_create_dir_ns+0x178/0x1d0 fs/sysfs/dir.c:59
[< inline >] create_dir lib/kobject.c:71
[<ffffffff81fa1b07>] kobject_add_internal+0x227/0xa60 lib/kobject.c:229
[< inline >] kobject_add_varg lib/kobject.c:366
[<ffffffff81fa2479>] kobject_add+0x139/0x220 lib/kobject.c:411
[<ffffffff82737a63>] device_add+0x353/0x1660 drivers/base/core.c:1088
[<ffffffff82738d8d>] device_register+0x1d/0x20 drivers/base/core.c:1206
[<ffffffff82cb77d3>] usb_create_ep_devs+0x163/0x260 drivers/usb/core/endpoint.c:195
[<ffffffff82c9f27b>] create_intf_ep_devs+0x13b/0x200 drivers/usb/core/message.c:1030
[<ffffffff82ca39d3>] usb_set_configuration+0x1083/0x18d0 drivers/usb/core/message.c:1937
[<ffffffff82cc9e2e>] generic_probe+0x6e/0xe0 drivers/usb/core/generic.c:172
[<ffffffff82caa7fa>] usb_probe_device+0xaa/0xe0 drivers/usb/core/driver.c:263
This patch prevents the problem by checking for duplicate endpoint
addresses during enumeration and skipping any duplicates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CONFIG_PM=n:
drivers/usb/core/hub.c:107: warning: ‘hub_usb3_port_prepare_disable’ declared inline after being called
drivers/usb/core/hub.c:107: warning: previous declaration of ‘hub_usb3_port_prepare_disable’ was here
To fix this, move hub_port_disable() after
hub_usb3_port_prepare_disable(), and adjust forward declarations.
Fixes: 37be66767e ("usb: hub: Fix auto-remount of safely removed or ejected USB-3 devices")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On a system with a defective USB device connected to an USB hub,
an endless sequence of port connect events was observed. The sequence
of events as observed is as follows:
- Port reports connected event (port status=USB_PORT_STAT_CONNECTION).
- Event handler debounces port and resets it by calling hub_port_reset().
- hub_port_reset() calls hub_port_wait_reset() to wait for the reset
to complete.
- The reset completes, but USB_PORT_STAT_CONNECTION is not immediately
set in the port status register.
- hub_port_wait_reset() returns -ENOTCONN.
- Port initialization sequence is aborted.
- A few milliseconds later, the port again reports a connected event,
and the sequence repeats.
This continues either forever or, randomly, stops if the connection
is already re-established when the port status is read. It results in
a high rate of udev events. This in turn destabilizes userspace since
the above sequence holds the device mutex pretty much continuously
and prevents userspace from actually reading the device status.
To prevent the problem from happening, let's wait for the connection
to be re-established after a port reset. If the device was actually
disconnected, the code will still return an error, but it will do so
only after the long reset timeout.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----
iQJRBAABCAA7FiEElLzh7wn96CXwjh2IzL64meEamQYFAlgu7+gdHGZlbGlwZS5i
YWxiaUBsaW51eC5pbnRlbC5jb20ACgkQzL64meEamQaDbxAAsgDPAp8QTx8D1d70
hSGyPZ55rmqlzBNbUUOQyk/AeN5xM3XVbjZNOxWn4c386iaDrngcqOrxjCbBRsje
b9yMESMiZsTPVlKXE45yXt//NHg1KUfpHON7rybaiFq0uqjUhnQf95DeYPgJVxit
7F9B+05XcNMyxYRoz6bGkRTU+lcJ6g3/orgKfp4t/hs8WUNXH6+71keMF+IdLYNH
mcPmJ8MXpfLzv8eweRwV0s/3flxCuFx1ksZ8cW6qHR5vX303X2sGTlinBmhfQapr
t0a+OBtLpZdNmjw/yB2odc/1jjLNRHpYU5xGqwouMx9Ca2PocFT2xFbmUWR23xp1
X0rkICRxcLPjZql2Uld5QHO9dPnF/FbX0Njuvxo+2r8ENE5/eG4C/RcYcRDmYPsu
u8k2rKFs0+yCOAU91rD8mayJVBWBJ4trqZFT0TcocCGsMTk8fTYpF1Iskj9Z4FKz
yo+lgyCCtp673ykGZ1ezsL6YWOmdrQv/PurKZqrXAmdhi6+mImLI/nAHtAdOZx0X
zK9MwPnwDxrPiqhrZ46+Bm/EjZI50TM44M1ldmCwKi/6/Nvy54DHMtjPI5/9205R
bjftW3DkVWAC//29RNcGEHtwiJFPEU/kdoRFOPhKGJ7ocCzFVSTFBgo02kDsC6De
Wouv2QTFuZN9s17o29YVD3bGJZM=
=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
Since usb_endpoint_maxp now returns only lower 11 bits mult
calculation here isn't correct anymore and that breaks webcam
for me. Patch make use of usb_endpoint_maxp_mult instead of
direct calculation.
Fixes: abb621844f ("usb: ch9: make usb_endpoint_maxp() return
only packet size")
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
USB-3 does not have any link state that will avoid negotiating a connection
with a plugged-in cable but will signal the host when the cable is
unplugged.
For USB-3 we used to first set the link to Disabled, then to RxDdetect to
be able to detect cable connects or disconnects. But in RxDetect the
connected device is detected again and eventually enabled.
Instead set the link into U3 and disable remote wakeups for the device.
This is what Windows does, and what Alan Stern suggested.
Cc: stable@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some of the USB core files were missing explicit license information.
As all files in the kernel tree are implicitly licensed under the
GPLv2-only, be explicit in case someone get confused looking at
individual files by using the SPDX nomenclature.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grub finds incorrect of_node path for devices behind usb hub.
Added devspec sysfs entry for devices behind usb hub so that
right of_node path is returned during grub sysfs walk for these
devices.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull more vfs updates from Al Viro:
">rename2() work from Miklos + current_time() from Deepa"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Replace current_fs_time() with current_time()
fs: Replace CURRENT_TIME_SEC with current_time() for inode timestamps
fs: Replace CURRENT_TIME with current_time() for inode timestamps
fs: proc: Delete inode time initializations in proc_alloc_inode()
vfs: Add current_time() api
vfs: add note about i_op->rename changes to porting
fs: rename "rename2" i_op to "rename"
vfs: remove unused i_op->rename
fs: make remaining filesystems use .rename2
libfs: support RENAME_NOREPLACE in simple_rename()
fs: support RENAME_NOREPLACE for local filesystems
ncpfs: fix unused variable warning
CURRENT_TIME macro is not appropriate for filesystems as it
doesn't use the right granularity for filesystem timestamps.
Use current_time() instead.
CURRENT_TIME is also not y2038 safe.
This is also in preparation for the patch that transitions
vfs timestamps to use 64 bit time and hence make them
y2038 safe. As part of the effort current_time() will be
extended to do range checks. Hence, it is necessary for all
file system timestamps to use current_time(). Also,
current_time() will be transitioned along with vfs to be
y2038 safe.
Note that whenever a single call to current_time() is used
to change timestamps in different inodes, it is because they
share the same time granularity.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In USB20 specification, describes in chapter 9.4.5: The Remote Wakeup
field can be modified by the SetFeature() and ClearFeature() requests
using the DEVICE_REMOTE_WAKEUP feature selector.
In USB30 specification, also describes in chapter 9.4.5: The Function
Remote Wakeup field can be modified by the SetFeature() requests
using the FUNCTION_SUSPEND feature selector. In chapter 9.4.9 Set
Feature reference, it describes Function Remote Wake Enabled/Disabled
at suspend options by SET_FEATURE.
In USB30 specification only mentioned SetFeature(), so we need use
SET_FEATURE replace CLEAR_FEATURE to disable USB30 function remote
wakeup in suspend options.
Signed-off-by: Yonglong Wu <yonglong.wu@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a new trigger responsible for turning on LED when USB
device gets connected to the selected USB port. This can can useful for
various home routers that have USB port(s) and a proper LED telling user
a device is connected.
The trigger gets its documentation file but basically it just requires
enabling it and selecting USB ports (e.g. echo 1 > ports/usb1-1).
There was a long discussion on design of this driver. Its current state
is a result of picking them most adjustable solution as others couldn't
handle all cases.
1) It wasn't possible for the driver to register separated trigger for
each USB port. Some physical USB ports are handled by more than one
controller and so by more than one USB port. E.g. USB 2.0 physical
port may be handled by OHCI's port and EHCI's port.
It's also not possible to assign more than 1 trigger to a single LED
and implementing such feature would be tricky due to syncing triggers
and sysfs conflicts with old triggers.
2) Another idea was to register trigger per USB hub. This wouldn't allow
handling devices with multiple USB LEDs and controllers (hubs)
controlling more than 1 physical port. It's common for hubs to have
few ports and each may have its own LED.
This final trigger is highly flexible. It allows selecting any USB ports
for any LED. It was also modified (comparing to the initial version) to
allow choosing ports rather than having user /guess/ proper names. It
was successfully tested on SmartRG SR400ac which has 3 USB LEDs,
2 physical ports and 3 controllers.
It was noted USB subsystem already has usb-gadget and usb-host triggers
but they are pretty trivial ones. They indicate activity only and can't
have ports specified.
In future it may be good idea to consider adding activity support to
usbport as well. This should allow switching to this more generic driver
and maybe marking old ones as obsolete.
This can be implemented with another sysfs file for setting mode. The
default mode wouldn't change so there won't be ABI breakage and so such
feature can be safely implemented later.
There was also an idea of supporting other devices (PCI, SDIO, etc.) but
as this driver already contains some USB specific code (and will get
more) these should be probably separated drivers (triggers).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get 1 warning when building kernel with W=1:
drivers/usb/core/hcd.c:2390:5: warning: no previous prototype for 'usb_bus_start_enum' [-Wmissing-prototypes]
In fact, these functions are declared in linux/usb/otg.h, so this patch
adds the missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before. However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.
Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid. It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below. To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Wade Berrier <wberrier@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dma_pfn_offset is not inherited correctly from the host controller,
it might result in sub-optimal configuration as bounce
buffer limit might be set to less than optimal level.
Consider the mass storage device case.
USB storage driver creates a scsi host for the mass storage interface in
drivers/usb/storage/usb.c
The scsi host parent device is nothing but the the USB interface device.
Now, __scsi_init_queue() calls scsi_calculate_bounce_limit() to find out
and set the block layer bounce limit.
scsi_calculate_bounce_limit() uses dma_max_pfn(host_dev) to get the
bounce_limit. host_dev is nothing but the device representing the
mass storage interface.
If that device doesn't have the right dma_pfn_offset, then dma_max_pfn()
is messed up and the bounce buffer limit is wrong.
e.g. On Keystone 2 systems, dma_max_pfn() is 0x87FFFF and dma_mask_pfn
is 0xFFFFF. Consider a mass storage use case: Without this patch,
usb scsi host device (usb-storage) will get a dma_pfn_offset of 0 resulting
in a dma_max_pfn() of 0xFFFFF within the scsi layer
(scsi_calculate_bounce_limit()).
This will result in bounce buffers being unnecessarily used.
Hint: On 32-bit ARM platforms dma_max_pfn() = dma_mask_pfn + dma_pfn_offset
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ULPI bus is not only for host, but for device mode too, so move
it out from host's Kconfig.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All kmalloc-based functions print enough information on failures.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UBSAN complains about a left shift by -1 in proc_do_submiturb(). This
can occur when an URB is submitted for a bulk or control endpoint on
a high-speed device, since the code doesn't bother to check the
endpoint type; normally only interrupt or isochronous endpoints have
a nonzero bInterval value.
Aside from the fact that the operation is illegal, it shouldn't matter
because the result isn't used. Still, in theory it could cause a
hardware exception or other problem, so we should work around it.
This patch avoids doing the left shift unless the shift amount is >= 0.
The same piece of code has another problem. When checking the device
speed (the exponential encoding for interrupt endpoints is used only
by high-speed or faster devices), we need to look for speed >=
USB_SPEED_SUPER as well as speed == USB_SPEED HIGH. The patch adds
this check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Vittorio Zecca <zeccav@gmail.com>
Tested-by: Vittorio Zecca <zeccav@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum value allowed for wMaxPacketSize of a high-speed interrupt
endpoint is 1024 bytes, not 1023.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper usb_of_get_child_node is defined at of.c, but missing its
declare as a global function. Fix it by adding related header file
as well as compile it on conditional of CONFIG_OF.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: linux-kernel@lists.codethink.co.uk
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The whole Kconfig entries of the USB subsystem are surrounded with
"if USB_SUPPORT" ... "endif", so CONFIG_USB_SUPPORT=y is surely met
when these two Kconfig options are visible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede has reported a difficulty in the Linux port of libusb.
When a device is removed, the poll() system call in usbfs starts
returning POLLERR as soon as udev->state is set to
USB_STATE_NOTATTACHED, but the outstanding URBs are not available for
reaping until some time later (after usbdev_remove() has been called).
This is awkward for libusb or other usbfs clients, although not an
insuperable problem.
At any rate, it's easy to change usbfs so that it returns POLLHUP as
soon as the state becomes USB_STATE_NOTATTACHED but it doesn't return
POLLERR until after the outstanding URBs have completed. That's what
this patch does; it uses the fact that ps->list is always on the
dev->filelist list until usbdev_remove() takes it off, which happens
after all the outstanding URBs have been cancelled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbdev_mmap allocates a buffer. The size of the buffer is determined
by a user. So with this code (no need to be root):
int fd = open("/dev/bus/usb/001/001", O_RDONLY);
mmap(NULL, 0x800000, PROT_READ, MAP_SHARED, fd, 0);
we can see a warning:
WARNING: CPU: 0 PID: 21771 at ../mm/page_alloc.c:3563 __alloc_pages_slowpath+0x1036/0x16e0()
...
Call Trace:
[<ffffffff8117a3ae>] ? warn_slowpath_null+0x2e/0x40
[<ffffffff815178b6>] ? __alloc_pages_slowpath+0x1036/0x16e0
[<ffffffff81516880>] ? warn_alloc_failed+0x250/0x250
[<ffffffff8151226b>] ? get_page_from_freelist+0x75b/0x28b0
[<ffffffff815184e3>] ? __alloc_pages_nodemask+0x583/0x6b0
[<ffffffff81517f60>] ? __alloc_pages_slowpath+0x16e0/0x16e0
[<ffffffff810565d4>] ? dma_generic_alloc_coherent+0x104/0x220
[<ffffffffa0269e56>] ? hcd_buffer_alloc+0x1d6/0x3e0 [usbcore]
[<ffffffffa0269c80>] ? hcd_buffer_destroy+0xa0/0xa0 [usbcore]
[<ffffffffa0228f05>] ? usb_alloc_coherent+0x65/0x90 [usbcore]
[<ffffffffa0275c05>] ? usbdev_mmap+0x1a5/0x770 [usbcore]
...
Allocations like this one should be marked as __GFP_NOWARN. So do so.
The size could be also clipped by something like:
if (size >= (1 << (MAX_ORDER + PAGE_SHIFT - 1)))
return -ENOMEM;
But I think the overall limit of 16M (by usbfs_increase_memory_usage)
is enough, so that we only silence the warning here.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steinar H. Gunderson <sesse@google.com>
Cc: Markus Rechberger <mrechberger@gmail.com>
Fixes: f7d34b445a (USB: Add support for usbfs zerocopy.)
Cc: 4.6+ <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Erroneous or malicious endpoint descriptors may have non-zero bits in
reserved positions, or out-of-bounds values. This patch helps prevent
these from causing problems by bounds-checking the wMaxPacketValue
entries in endpoint descriptors and capping the values at the maximum
allowed.
This issue was first discovered and tests were conducted by Jake Lamberson
<jake.lamberson1@gmail.com>, an intern working for Rosie Hall.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: roswest <roswest@cisco.com>
Tested-by: roswest <roswest@cisco.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The locking in hub_activate() is not adequate to provide full mutual
exclusion with hub_quiesce(). The subroutine locks the hub's
usb_interface, but the callers of hub_quiesce() (such as
hub_pre_reset() and hub_event()) hold the lock to the hub's
usb_device.
This patch changes hub_activate() to make it acquire the same lock as
those other routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org> #4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early-exit pathway in hub_activate, added by commit e50293ef97
("USB: fix invalid memory access in hub_activate()") needs
improvement. It duplicates code that is already present at the end of
the subroutine, and it neglects to undo the effect of a
usb_autopm_get_interface_no_resume() call.
This patch fixes both problems by making the early-exit pathway jump
directly to the end of the subroutine. It simplifies the code at the
end by merging two conditionals that actually test the same condition
although they appear different: If type < HUB_INIT3 then type must be
either HUB_INIT2 or HUB_INIT, and it can't be HUB_INIT because in that
case the subroutine would have exited earlier.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org> #4.4+
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory leak and unbalanced reference count:
If the hub gets disconnected while the core is still activating it, this
can result in leaking memory of few USB structures.
This will happen if we have done a kref_get() from hub_activate() and
scheduled a delayed work item for HUB_INIT2/3. Now if hub_disconnect()
gets called before the delayed work expires, then we will cancel the
work from hub_quiesce(), but wouldn't do a kref_put(). And so the
unbalance.
kmemleak reports this as (with the commit e50293ef97 backported to
3.10 kernel with other changes, though the same is true for mainline as
well):
unreferenced object 0xffffffc08af5b800 (size 1024):
comm "khubd", pid 73, jiffies 4295051211 (age 6482.350s)
hex dump (first 32 bytes):
30 68 f3 8c c0 ff ff ff 00 a0 b2 2e c0 ff ff ff 0h..............
01 00 00 00 00 00 00 00 00 94 7d 40 c0 ff ff ff ..........}@....
backtrace:
[<ffffffc0003079ec>] create_object+0x148/0x2a0
[<ffffffc000cc150c>] kmemleak_alloc+0x80/0xbc
[<ffffffc000303a7c>] kmem_cache_alloc_trace+0x120/0x1ac
[<ffffffc0006fa610>] hub_probe+0x120/0xb84
[<ffffffc000702b20>] usb_probe_interface+0x1ec/0x298
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
[<ffffffc0005d3164>] bus_for_each_drv+0x78/0xac
[<ffffffc0005d4ee0>] device_attach+0x6c/0x9c
[<ffffffc0005d42b8>] bus_probe_device+0x28/0xa0
[<ffffffc0005d23a4>] device_add+0x324/0x604
[<ffffffc000700fcc>] usb_set_configuration+0x660/0x6cc
[<ffffffc00070a350>] generic_probe+0x44/0x84
[<ffffffc000702914>] usb_probe_device+0x54/0x74
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
Deadlocks:
If the hub gets disconnected early enough (i.e. before INIT2/INIT3 are
finished and the init_work is still queued), the core may call
hub_quiesce() after acquiring interface device locks and it will wait
for the work to be cancelled synchronously. But if the work handler is
already running in parallel, it may try to acquire the same interface
device lock and this may result in deadlock.
Fix both the issues by removing the call to cancel_delayed_work_sync().
CC: <stable@vger.kernel.org> #4.4+
Fixes: e50293ef97 ("USB: fix invalid memory access in hub_activate()")
Reported-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dependencies were impossible to handle preventing
drivers for CDC devices not which are not network drivers
from using the common parser.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BugLink: http://bugs.launchpad.net/bugs/1498667
As reported in BugLink, this device has an issue with Linux Power
Management so adding a quirk. This quirk was reccomended by Alan Stern:
http://lkml.iu.edu/hypermail/linux/kernel/1606.2/05590.html
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB core contains a bug that can show up when a USB-3 host
controller is removed. If the primary (USB-2) hcd structure is
released before the shared (USB-3) hcd, the core will try to do a
double-free of the common bandwidth_mutex.
The problem was described in graphical form by Chung-Geol Kim, who
first reported it:
=================================================
At *remove USB(3.0) Storage
sequence <1> --> <5> ((Problem Case))
=================================================
VOLD
------------------------------------|------------
(uevent)
________|_________
|<1> |
|dwc3_otg_sm_work |
|usb_put_hcd |
|peer_hcd(kref=2)|
|__________________|
________|_________
|<2> |
|New USB BUS #2 |
| |
|peer_hcd(kref=1) |
| |
--(Link)-bandXX_mutex|
| |__________________|
|
___________________ |
|<3> | |
|dwc3_otg_sm_work | |
|usb_put_hcd | |
|primary_hcd(kref=1)| |
|___________________| |
_________|_________ |
|<4> | |
|New USB BUS #1 | |
|hcd_release | |
|primary_hcd(kref=0)| |
| | |
|bandXX_mutex(free) |<-
|___________________|
(( VOLD ))
______|___________
|<5> |
| SCSI |
|usb_put_hcd |
|peer_hcd(kref=0) |
|*hcd_release |
|bandXX_mutex(free*)|<- double free
|__________________|
=================================================
This happens because hcd_release() frees the bandwidth_mutex whenever
it sees a primary hcd being released (which is not a very good idea
in any case), but in the course of releasing the primary hcd, it
changes the pointers in the shared hcd in such a way that the shared
hcd will appear to be primary when it gets released.
This patch fixes the problem by changing hcd_release() so that it
deallocates the bandwidth_mutex only when the _last_ hcd structure
referencing it is released. The patch also removes an unnecessary
test, so that when an hcd is released, both the shared_hcd and
primary_hcd pointers in the hcd's peer will be cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
Tested-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Acer C120 LED Projector is a USB-3 connected pico projector which
takes both its power and video data from USB-3.
In combination with some hubs this device does not play well with
lpm, so disable lpm for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly sort all the entries by vendor id.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stack object “ci” has a total size of 8 bytes. Its last 3 bytes
are padding bytes which are not initialized and leaked to userland
via “copy_to_user”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB driver is bound to an interface (either through probing or
by claiming it) or is unbound from an interface, the USB core always
disables Link Power Management during the transition and then
re-enables it afterward. The reason is because the driver might want
to prevent hub-initiated link power transitions, in which case the HCD
would have to recalculate the various LPM parameters. This
recalculation takes place when LPM is re-enabled and the new
parameters are sent to the device and its parent hub.
However, if the driver does not want to prevent hub-initiated link
power transitions then none of this work is necessary. The parameters
don't need to be recalculated, and LPM doesn't need to be disabled and
re-enabled.
It turns out that disabling and enabling LPM can be time-consuming,
enough so that it interferes with user programs that want to claim and
release interfaces rapidly via usbfs. Since the usbfs kernel driver
doesn't set the disable_hub_initiated_lpm flag, we can speed things up
and get the user programs to work by leaving LPM alone whenever the
flag isn't set.
And while we're improving the way disable_hub_initiated_lpm gets used,
let's also fix its kerneldoc.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Matthew Giassa <matthew@giassa.net>
CC: Mathias Nyman <mathias.nyman@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit e3345db850, which
broke system resume for a large class of devices.
Devices that after having been reset during resume need to be rebound
due to a missing reset_resume callback, are now left in a suspended
state. This specifically broke resume of common USB-serial devices,
which are now unusable after system suspend (until disconnected and
reconnected) when USB persist is enabled.
During resume, usb_resume_interface will set the needs_binding flag for
such interfaces, but unlike system resume, run-time resume does not
honour it.
Cc: stable <stable@vger.kernel.org> # 4.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the root hub device is added to the bus, it tries to get pins
information from pinctrl (see pinctrl_bind_pins, at really_probe), if
the pin information is described at DT, it will show below error since
the root hub's device node is the same with controller's, but controller's
pin has already been requested when it is added to platform bus.
imx6q-pinctrl 20e0000.iomuxc: pin MX6Q_PAD_GPIO_1 already
requested by 2184000.usb; cannot claim for usb1
imx6q-pinctrl 20e0000.iomuxc: pin-137 (usb1) status -22
imx6q-pinctrl 20e0000.iomuxc: could not request pin 137
(MX6Q_PAD_GPIO_1) from group usbotggrp-3 on device 20e0000.iomuxc
usb usb1: Error applying setting, reverse things back
To fix this issue, we move the root hub's device node assignment (equals
to contrller's) after device is added to bus, we only need to know root
hub's device node information after the device under root hub is created,
so this movement will not affect current function.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reported-by: Lars Steubesand <lars.steubesand@philips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
