Try to force the PHY clock buffer enables to make the clock routing
work.
v2: Fix the pipe B case to actually enable CH0 clock buffers
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These should make it possible to feed port C from pipe A or port B from
pipe B. Didn't quite seem to work though.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The spec only tells us to set individual bits here and there. So we use
RMW for most things. Do the same for the swing calc init.
Eventually we should optimize things to just blast the final value in
with group access whenever possible. But to do that someone needs to
take a good look at what's the reset value for each registers, and
possibly if the BIOS manages to frob with some of them. For now
use RMW access always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like PCS, TX group reads return 0xffffffff. So we need to target each
lane separately if we want to use RMW cycles to update the registers.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All PCS groups access reads return 0xffffffff, so we can't use group
access for RMW cycles. Instead target each spline separately.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fight conflict with misplaced ; .... ARGH!]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits we've been setting so far only progagate the reset singal to
the data lanes. To actaully force the reset signal we need to set another
override bit.
v2: Fix mispalced ';' (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Seems like we shouldn't leave the data lane resert deasserted when
the port if disabled. So propagate the reset the data lanes in
the encoder .post_disable() hook.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to pick the correct data lanes based on the port not the
pipe, so move the data lane deassert into the encoder .pre_enable()
hook from the chv_enable_pll().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the encoder .get_config hooks to report the correct active pipe for
CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV the GMBUS port for port D is different from other gmch platforms
which have port D. Fix it up.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CHV pipe C can driver only port D, and pipes A and B can drivbe only
ports B and C. Configure the crtc_mask appropriately to reflect that.
v2: Moar braces (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to dp the only thing we do is call intel_write_eld and prepare
a bit of state for the enable hooks. The only difference is that we
write that to the hardware instead of keeping track of it somewhere in
software.
Still we can just move all this to the very first enable hook.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those functions are only used on vlv platforms, so no need to check.
Especially if we're not too consistent about it.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Including state readout and cross-checking. This allows us to get rid
of crtc->eld_vld on hsw+. It also means that fastboot will be unhappy
if the BIOS hasn't set up the audio routing like we want it too.
Wrt fastboot and external screens I see a few options:
- Don't.
- Try to fix up eld, infoframes and audio settings after the fact. But
that means some pretty extensive reworking of our code which
currently does all this while the pipe/port is still off.
I won't bother with converting SDVO over to this because the audio
support for SDVO is very lacking:
- We don't update the eld.
- We don't update the audio state on the sdvo encoder.
- We don't check whether the platform can even feed audio to the sdvo
encoder.
I've converted hdmi, dp & ddi all in one go since ddi needs both hdmi
and dp converted and so doing it step-by-step would have required a
few intermediate hacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also add state readout and cross-check support. The only invasive change
is wiring up the new flag to the ->set_infoframes callbacks.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For compliance we really should be sending NULL infoframes always
when we detect a hdmi capable monitor. Also remove the now redudant
setting for the has_audio case and enforce that audio is only
possible with a hdmi sink.
Reviewed-by: Naresh Kumar Kachhi <naresh.kumar.kachhi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With additional of pipe C, current 1 bit registers for pipe select
for HDMI and DP are no longer able to gather for 3 pipes. As a result,
new bits location in the same registers are added.
For HDMI, VLV uses bit 30, CHV uses bit 24-25.
For DP, VLV uses bit 30, CHV uses bit 16-17.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Added programming phy layer for CHV based on "Application note for 1273
CHV Display phy".
v2: Rebase the code and do some cleanup.
v3: Rework based on Ville review.
-Fix the macro where the ch info need to swap, and add parens to ?
operator.
-Fix wrong bit define for DPIO_PCS_SWING_CALC_0 and
DPIO_PCS_SWING_CALC_1 and rename for meaningful.
-Add some comments for CHV specific DPIO registers.
-Change the dp margin registery value to decimal to align with the
doc.
-Fix the not clearing some value in vlv_dpio_read before write again.
-Create new hdmi/dp encoder function for chv instead of share with
valleyview.
v4: Rebase the code after rename the DPIO registers define and upstream
change.
Based on Ville review.
-For unique transition scale selection, after Ville point out, look
like the doc might wrong for the bit 26. Use bit 27 for ch0 and
ch1.
-Break up some dpio write value into two/three steps for readability.
-Remove unrelated change.
-Add some shift define for some registers instead just give the hex
value.
-Fix a bug where write to wrong VLV_TX_DW3.
v5: Based on Ville review.
- Move tx lane latency optimal setting from chv_dp_pre_pll_enable to
chv_pre_enable_dp, and chv_hdmi_pre_pll_enable to
chv_hdmi_pre_enable respectively.
- Fix typo in one margin_reg_value for DP_TRAIN_VOLTAGE_SWING_400.
- Clear DPIO_TX_UNIQ_TRANS_SCALE_EN for DP and HDMI.
- Mask the old deemph and swing bits for hdmi.
v6: Remove stub for pre_pll_enable for dp and hdmi.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[vsyrjala: Don't touch panel power sequencing on DP]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
In commit
commit 6375b768a9
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Mar 3 11:33:36 2014 +0200
drm/i915: Reject >165MHz modes w/ DVI monitors
the driver started to filter out display modes which exceed the
single-link DVI 165Mz dotclock limits when the monitor doesn't report
itself as being HDMI compliant. The intent was to filter out all
EDID derived modes that require dual-link DVI to operate since we
don't support dual-link.
However the patch went a bit too far and also causes the driver to reject
such modes even when specified by the user. Normally we don't check the
sink limitations when setting a mode from the user. This allows the user
to specify any mode whether the sink reports to support it or not. This
can be useful since often the sinks support more modes than they report
in the EDID.
So relax the checks a bit, and apply the single-link DVI dotclock limit
only when filtering the mode list, and ignore the limit when setting
a user specified mode.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=72961
Tested-by: Nicholas Vinson <nvinson@comcast.net>
Cc: stable@vger.kernel.org [3.14]
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Needs to happen after clock is running or it doesn't behave correctly.
v2: fix subject (Ville)
make it clearer that this occurs in pre_enable (Paulo)
misc bikesheds (Paulo)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Allows sending of the null packets for conformance.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We also do a disable later when we write a specific infoframe, but here
we do it to prevent sending a stale one before updating the infoframes.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we end up bouncing these around between ports.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec is a bit unclear whether HDMI+HDMI cloning should work on g4x.
Tests on real hardware say that it does. Since g4x can't send
infoframes to more than one HDMI port anyway, we don't lose anything
by allow it.
For PCH platforms BSpec explicitly forbids HDMI+HDMI cloning.
Whether HDMI+HDMI cloning might also work on VLV is a bit unclear, but
since we'd at least lose the capability of sending infoframes to more
than one cloned HDMI port, it doesn't seem like a good idea to allow it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73850
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HDMI+VGA cloning should be supported on all platforms. The only real
obstacle is the 1.5x clock adjustment for 12bpc HDMI, but that is now
taken care of, so we can allow HDMI+VGA cloning.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73850
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When cloning HDMI with other output types, we can't use 12bpc since the
clocks for the other encoder types would be off. So have
intel_hdmi_compute_config() check if there are other encoders besides
HDMI being fed from the same pipe, and if so, pick 8bpc insted if 12bpc.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTHSaRAAoJEHm+PkMAQRiG7G8IAJHElwFDNSQE7Y9MmbicrAMG
kfjhBtBpTaVrJKQXegCNUwDaLLyC4oLIxDheW84oPXbrEGDLqPtBov/hrcFkHVr4
lh/ZYk02nYtcfpN0JnL/Yj2oKHVmBWs0vFlM7StSFsJCj10DoCVQQdmAJ8XODTPo
CXMapk+UikTX1TlIO8+B5toyl3R1OqPmW211UV1vQVLKy66hu+MKVN/V+/EyopL0
1jO81EDpaRaeIJh1/okcyUoIq9pqLkAWNpeQ7uyXZ+Sfivt9RXwLYKmAB3lP20Hc
ZMIIoHSCyYRFjxLlQvt02bA9nY4wTY7YN5kZ2kk65y7TFfhcGsCw1Sc69iyCoKs=
=CJcA
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc6' into drm-intel-next-queued
Linux 3.14-rc6
I need the hdmi/dvi-dual link fixes in 3.14 to avoid ugly conflicts
when merging Ville's new hdmi cloning support into my -next tree
Conflicts:
drivers/gpu/drm/i915/Makefile
drivers/gpu/drm/i915/intel_dp.c
Makefile cleanup conflicts with an acpi build fix, intel_dp.c is
trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we allow encoders to indicate whether they can be part of a
cloned set with just one flag. That's not flexible enough to describe
the actual hardware capabilities. Instead make it a bitmask of encoder
types with which the current encoder can be cloned.
For now we set the bitmask to allow DVO+DVO and DVO+VGA, which should
match what the old boolean flag allowed. We will add some more cloning
options in the future.
Note that this patch also removes the encoder.possible_clones setting
from encoder setup code - we compute this dynamically.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add Ville's explanation why removing the encoder
possible_clones is save.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the encoder is tied to its port, we need to make sure the power
domain for that port is on before reading out the encoder HW state.
Note that this also covers also all connector get_hw_state handlers,
since all those just call the corresponding encoder get_hw_state
handler, which checks - after this change - for all power domains
the connector needs.
v2:
- no change
v3:
- push down the power domain checks into the specific encoder
get_hw_state handlers (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The connector detect and get_mode handlers need to access the port
specific HW blocks to read the EDID etc. Get/put the port power domains
around these handlers.
v2:
- get port power domain for HDMI too (Ville)
- get port power domain for the DP,HDMI audio detect handlers (Jesse)
- Leave the intel_runtime_pm_get/put in the DP detect function in place.
Instead of just removing them, these should be moved to the appropriate
power_well enable/disable handlers. We can do this after Paulo's
'Merge PC8 with runtime PM, v2' patchset.
v3:
- rebased on latest -nightly
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Single-link DVI max dotclock is 165MHz. Filter out modes with higher
dotclock when the monitor doesn't support HDMI.
Modes higher than 165 MHz were allowed in
commit 7d148ef51a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jul 22 18:02:39 2013 +0200
drm/i915: fix hdmi portclock limits
Also don't attempt to use 12bpc mode with DVI monitors.
Cc: Adam Nielsen <a.nielsen@shikadi.net>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75345
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70331
Tested-by: Ralf Jung <post+kernel@ralfj.de>
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Since
commit d9255d5714
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Sep 26 20:05:59 2013 -0300
it became clear that we need to separate the unload sequence into two
parts:
1. remove all interfaces through which new operations on some object
(crtc, encoder, connector) can be started and make sure all pending
operations are completed
2. do the actual tear down of the internal representation of the above
objects
The above commit achieved this separation for connectors by splitting
out the sysfs removal part from the connector's destroy callback and
doing this removal before calling drm_mode_config_cleanup() which does
the actual tear-down of all the drm objects.
Since we'll have to customize the interface removal part for different
types of connectors in the upcoming patches, add a new unregister
callback and move the interface removal part to it.
No functional change.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Antti Koskipää <antti.koskipaa@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a couple of switch cases to compute the port value for the
VIDEO_DIP_CTL register. Replace them with a simple macro.
We do lose a few BUG() calls, but many people may consider that
an improvement.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
RFCv2: Reorganize array indexing so that full offsets can be used as
is. It makes grepping for registers in i915_reg.h much easier. Also
move offset arrays to intel_device_info.
v1: Fixed offsets for VLV, proper eDP handling
v2: Fixed BCLRPAT, PIPESRC, PIPECONF and DSP* macros.
v3: Added EDP pipe comment, removed redundant offset arrays for
MSA_MISC and DDI_FUNC_CTL.
v4: Rename patch and report object size increase.
v5: Change location of commas, add PIPE_EDP into enum pipe
v6: Insert PIPE_EDP_OFFSET into pipe offset array
v7: Set I915_MAX_PIPES back to 3, change more registers accessors
to use the new macros, get rid of _PIPE_INC and add dev_priv
as a parameter where required by the new macros.
Upcoming hardware will not have the various display pipe register
ranges evenly spaced in memory. Change register address calculations
into array lookups.
Tested on SNB, VLV, IVB, Gen2 and HSW w/eDP.
I left the UMS cruft untouched.
Size differences:
text data bss dec hex filename
596431 4634 56 601121 92c21 i915.ko (new)
593199 4634 56 597889 91f81 i915.ko (old)
Signed-off-by: Antti Koskipaa <antti.koskipaa@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't modify the packed infoframe data, so we should keep the
const qualifier in place. Just pass the buffer as 'const void *'
instead of 'const uint8_t *' and we can drop the cast entirely.
v2: Do intel_sdvo_write_infoframe() as well
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We had some mode_valid() vfuncs returning an int, others the enum. Let's
use the latter everywhere.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in Jani's backlight rework branch. This was merged through a
separate branch to be able to sort out the Broadwell conflicts
properly before pulling it into the main development branch.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
vlv_dpio_read/write should be describe more in PHY centric instead of
display controller centric.
Create a enum dpio_channel for channel index and enum dpio_phy for PHY
index. This should better to gather for upcoming platform.
v2: Rebase the code based on
drm/i915/vlv: Fix typo in the DPIO register define.
v3: Rename vlv_phy to dpio_phy_iosf_port and define additional macro
DPIO_PHY, and remove unrelated change. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like HSW.
This means we can scan out a mode with a 300Mhz pixel clock with a depth
of 24 bits, but only a 200Mhz one with a 36bits depth.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some VLV PHY/PLL DPIO registers have group/lane/channel access. Current
DPIO register definition doesn't have a structure way to break them
down. As a result it is not easy to match the PHY/PLL registers with the
configdb document. Rename those registers based on the configdb for easy
cross references, and without the need to check the offset in the header
file.
New format is as following.
<platform name>_<DPIO component><optional lane #>_DW<dword # in the
doc>_<optional channel #>
For example,
VLV_PCS_DW0 - Group access to PCS for lane 0 to 3 for PCS DWORD 0.
VLV_PCS01_DW0_CH0 - PCS access to lane 0/1, channel 0 for PCS DWORD 0.
Another example is
VLV_TX_DW0 - Group access to TX lane 0 to 3 for TX DWORD 0
VLV_TX0_DW0 - Refer to TX Lane 0 access only for TX DWORD 0.
There is no functional change on this patch.
v2: Rebase based on previous patch change.
v3: There may be configdb different version that document the start DW
differently. Add a comment to clarify. Fix up some mismatch start DW
for second PLL block. (Ville)
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no functional change on this patch. Only rename several
hdmi encoder function name which suppose to use only by valleyview from
intel_hdmi_pre_pll_enable to vlv_hdmi_pre_pll_enable, and etc.
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For some reason, every single time I try to run module_reload
something tries to read the connector sysfs files. This happens
after we destroy the encoders and before we destroy the connectors, so
when the sysfs read triggers the connector detect() function,
intel_conector->encoder points to memory that was already freed.
The bad backtrace is just:
[<ffffffff8163ca9a>] dump_stack+0x54/0x74
[<ffffffffa00c2c8e>] intel_dp_detect+0x1e/0x4b0 [i915]
[<ffffffffa001913d>] status_show+0x3d/0x80 [drm]
[<ffffffff813d5340>] dev_attr_show+0x20/0x60
[<ffffffff81221f50>] ? sysfs_read_file+0x80/0x1b0
[<ffffffff81221f79>] sysfs_read_file+0xa9/0x1b0
[<ffffffff811aaf1e>] vfs_read+0x9e/0x170
[<ffffffff811aba4c>] SyS_read+0x4c/0xa0
[<ffffffff8164e392>] system_call_fastpath+0x16/0x1b
But if you add tons of memory checking debug options to your Kernel
you'll also see:
- general protection fault: 0000
- BUG kmalloc-4096 (Tainted: G D W ): Poison overwritten
- INFO: Allocated in intel_ddi_init+0x65/0x270 [i915]
- INFO: Freed in intel_dp_encoder_destroy+0x69/0xb0 [i915]
Among a bunch of other error messages.
So this commit just destroys the sysfs files before both the encoder
and connectors are freed.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
struct drm_mode_display now has a separate crtc_ version of the clock to
be used when we're talking about the timings given to the harwadre (was
far as the mode is concerned).
This commit is really the result of a git grep adjusted_mode.*clock and
replacing those by adjusted_mode.crtc_clock. No functional change.
v2: Rebased on drm-intel-queued-next
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Done while reviewing all our allocations for fubar. Also a few errant
cases of lacking () for the sizeof operator - just a bit of OCD.
I've left out all the conversions that also should use kcalloc from
this patch (it's only 2).
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pixel clock should come from adjusted_mode not requested_mode.
In this case the two should be the same as we don't currently
overwrite the clock in the case of HDMI. But let's make the code
safe against such things happening in the future.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that adjusted_mode.clock no longer contains the pixel_multiplier, we
can kill the get_clock() callback and instead do the clock readout
in get_pipe_config().
Also i9xx_crtc_clock_get() can now extract the frequency of the PCH
DPLL, so use it to populate port_clock accurately for PCH encoders.
For DP in port A the encoder is still responsible for filling in
port_clock. The FDI adjusted_mode.clock extraction is kept in place
for some extra sanity checking, but we no longer need to pretend it's
also the port_clock.
In the encoder get_config() functions fill out adjusted_mode.clock
based on port_clock and other details such as the DP M/N values,
HDMI 12bpc and SDVO pixel_multiplier. For PCH encoders we will then
do an extra sanity check to make sure the dotclock we derived from
the FDI configuratiuon matches the one we derive from port_clock.
DVO doesn't exist on PCH platforms, so it doesn't need to anything
but assign adjusted_mode.clock=port_clock. And DDI is HSW only, so
none of the changes apply there.
v2: Use hdmi_reg color format to detect 12bpc HDMI case
v3: Set adjusted_mode.clock for LVDS too
v4: Rename ironlake_crtc_clock_get to ironlake_pch_clock_get,
eliminate the useless link_freq variable.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The patch doesn't contain functional change, but is to prepare for
future platform which has different DPIO phy. The additional pipe
parameter will use to select which phy to target for.
v2: Update the commit message and add static for the new function.
(Jani/Ville)
Signed-off-by: Chon Ming Lee <chon.ming.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
