Fix the g1 interrupt free code such that is masks any further
interrupts, and then releases the interrupt.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trying to remove an IRQ domain that was not created results in an
Opps. Add the necessary checks that the irqs were created before
freeing them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some architectures may not define IRQ_DOMAIN (like m32r), fixes
undefined references to IRQ_DOMAIN functions.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPEED_UNFORCED indicates the MAC & PHY should perform
auto-negotiation to determine a speed which works. If this is called
for, don't set the force bit. If it is set, the MAC actually does
10Gbps, why the internal PHYs don't support.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent refactoring of setting the MAC configuration broke setting
of RGMII delays, via the phy-mode, on the 6351 family. Add the missing
ops to the structure.
Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RGMII modes delays can be set via strapping pings or EEPROM.
Don't change them unless explicitly asked to change them. The recent
refactoring of setting the MAC configuration changed this behaviours,
in that CPU and DSA ports have any pre-configured RGMII delays
removed. This breaks the Armada 370RD board. Restore the previous
behaviour, in that RGMII delays are only applied/removed when
explicitly asked for via an phy-mode being PHY_INTERFACE_MODE_RGMII*
Fixes: 7340e5ecdbb1 ("net: dsa: mv88e6xxx: setup port's MAC")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have setters to configure the port's MAC, use them to
refactor the port setup and adjust_link code.
Note that port's MAC speed, duplex or RGMII delay must not be changed
unless the port's link is forced down. So wrap all that in a
mv88e6xxx_port_setup_mac function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the two bits for link, duplex or RGMII delays are used the same
way on chips supporting the said feature, the two bits for speed have
different meaning for most of the chips out there.
Speed value is stored in bits 1:0, 0x3 means unforce (normal detection).
Some chips reuse values for alternative speeds when bit 12 is set.
Newer chips with speed > 1Gbps reuse value 0x3 thus need a new bit 13.
Here are the values to write in register 0x1 to (un)force speed:
| Speed | 88E6065 | 88E6185 | 88E6352 | 88E6390 | 88E6390X |
| ------- | ------- | ------- | ------- | ------- | -------- |
| 10 | 0x0000 | 0x0000 | 0x0000 | 0x2000 | 0x2000 |
| 100 | 0x0001 | 0x0001 | 0x0001 | 0x2001 | 0x2001 |
| 200 | 0x0002 | NA | 0x1001 | 0x3001 | 0x3001 |
| 1000 | NA | 0x0002 | 0x0002 | 0x2002 | 0x2002 |
| 2500 | NA | NA | NA | 0x3003 | 0x3003 |
| 10000 | NA | NA | NA | NA | 0x2003 |
| unforce | 0x0003 | 0x0003 | 0x0003 | 0x0000 | 0x0000 |
This patch implements a generic mv88e6xxx_port_set_speed() function used
by chip-specific wrappers to filter supported ports and speeds.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips such as 88E6352 and 88E6390 can be programmed to add delays
to RXCLK for IND inputs or to GTXCLK for OUTD outputs when port is in
RGMII mode.
Add a port function to program such delays according to the provided PHY
interface mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to port's link, add setter to force port's half duplex, full
duplex or let normal duplex detection occurs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the chips will have a port register control bits to force the
port's link up, down, or let normal link detection occurs.
Implement such operation to use it later when setting duplex, etc.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to set the port 802.1Q mode.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add port functions to access the ports default VID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions to port files to access the ports default FID.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a port function to access the Port Based VLAN Map register.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the port STP state setter to the port files.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell switches contains one internal SMI device per port, called
"Port Registers". Depending on the model, the addresses of these devices
start from 0x0, 0x8 or 0x10.
Start moving Port Registers specific code to their own files.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the function
and data fields.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/dsa/mv88e6xxx/chip.c:2866:5: warning:
symbol 'mv88e6xxx_g1_set_switch_mac' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch can have up to two interrupt controllers. One of these
contains the interrupts from the integrated PHYs, so is useful to
export. The Marvell PHY driver can then be used in interrupt mode,
rather than polling, speeding up PHY handling and reducing load on the
MDIO bus.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove EEPROM flags in favor of new {get,set}_eeprom chip-wide
functions in the mv88e6xxx_ops structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a set_switch_mac chip-wide function to mv88e6xxx_ops and remove
MV88E6XXX_FLAG_G2_SWITCH_MAC flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a mv88e6xxx_ops structure to describe supported chip-wide
functions and assign the correct variant to the chip models.
For the moment, add only PHY access routines. This allows to get rid of
the PHY ops structures and the usage of PHY flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_ops is used to describe how to access the chip registers.
It can be through SMI (via an MDIO bus), or via another interface such
as crafted remote management frames.
The correct BUS operations structure is chosen at runtime, depending on
the chip address and connectivity.
We will need the mv88e6xxx_ops name for future chip-wide operation
structure, thus rename mv88e6xxx_ops to more explicit mv88e6xxx_bus_ops.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The STU (if the switch has one) is abstracted and accessed through the
VTU operations and data registers.
Thus rename the mv88e6xxx_vtu_stu_entry struct to mv88e6xxx_vtu_entry.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an mv88e6xxx_num_ports helper instead of digging in the chip info
structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_num_databases will be used by shared code, so move it
inline to the header file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to describe the presence of Global 1 ATU FID register (0x01)
and VTU FID register (0x02), instead of checking families.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to the ports, phys, and Global SMI devices, abstract the SMI
device address of the Global 2 registers in a few g2 static helpers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Global (1) internal SMI device is an extended set of registers
containing ATU, PPU, VTU, STU, etc.
It is present on every switches, usually at SMI address 0x1B. But old
models such as 88E6060 access it at address 0xF, thus using REG_GLOBAL
is erroneous.
Add a global1_addr info member used by mv88e6xxx_g1_{read,write} and
mv88e6xxx_g1_wait helpers in a new global1.c file.
This patch finally removes _mv88e6xxx_reg_{read,write}, in favor on the
appropriate helpers. No functional changes here.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/dsa/mv88e6xxx/chip.c:219:5: warning:
symbol 'mv88e6xxx_port_read' was not declared. Should it be static?
drivers/net/dsa/mv88e6xxx/chip.c:227:5: warning:
symbol 'mv88e6xxx_port_write' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA layer handles port fast ageing on correct STP change,
simplify _mv88e6xxx_port_state and implement mv88e6xxx_port_fast_age.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are soon going to run out of flag bits on 32bit systems. Convert to
unsigned long long.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a device coming soon which places its port registers
somewhere different to all other Marvell switches supported so far.
Add helper functions for reading/writing port registers, making it
easier to handle this new device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An address can be loaded in the ATU with multiple ports, for instance
when adding multiple ports to a Multicast group with "bridge mdb".
The current code doesn't allow that. Add an helper to get a single entry
from the ATU, then set or clear the requested port, before loading the
entry back in the ATU.
Note that the required _mv88e6xxx_atu_getnext function is defined below
mv88e6xxx_port_db_load_purge, so forward-declare it for the moment. The
ATU code will be isolated in future patches.
Fixes: 83dabd1fa8 ("net: dsa: mv88e6xxx: make switchdev DB ops generic")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since not every chip has a Global2 set of registers, make its support
optional, in which case the related functions will return -EOPNOTSUPP.
This also allows to reduce the size of the mv88e6xxx driver for devices
such as home routers embedding Ethernet chips without Global2 support.
It is present on most recent chips, thus enable its support by default.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips are composed of multiple SMI devices. One of them at
address 0x1C is called Global2. It provides an extended set of
registers, used for interrupt control, EEPROM access, indirect PHY
access (to bypass the PHY Polling Unit) and cross-chip related setup.
Most chips have it, but some others don't (older ones such as 6060).
Now that its related code is isolated in mv88e6xxx_g2_* functions, move
it to its own global2.c file, making most of its setup code static.
Document each registers in the meantime.
Its compilation can be later avoided for chips without such registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mv88e6xxx.c file has been renamed, the driver compiled as a
module is called chip.ko instead of mv88e6xxx.ko. Fix this.
Fixes: fad09c73c2 ("net: dsa: mv88e6xxx: rename single-chip support")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access the priv member of the dsa_switch structure directly, instead of
having an unnecessary helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the MDB operations. This consists of
loading/purging/dumping multicast addresses for a given port in the ATU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDB support for the mv88e6xxx driver will be very similar to the FDB
support, since it consists of loading/purging/dumping address to/from
the Address Translation Unit (ATU).
Prepare the support for MDB by making the FDB code accessing the ATU
generic. The FDB operations now provide access to the unicast addresses
while the MDB operations will provide access to the multicast addresses.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the dsa_switch_driver structure contains only function pointers
as it is supposed to, rename it to the more appropriate dsa_switch_ops,
uniformly to any other operations structure in the kernel.
No functional changes here, basically just the result of something like:
s/dsa_switch_driver *drv/dsa_switch_ops *ops/g
However keep the {un,}register_switch_driver functions and their
dsa_switch_drivers list as is, since they represent the -- likely to be
deprecated soon -- legacy DSA registration framework.
In the meantime, also fix the following checks from checkpatch.pl to
make it happy with this patch:
CHECK: Comparison to NULL could be written "!ops"
#403: FILE: net/dsa/dsa.c:470:
+ if (ops == NULL) {
CHECK: Comparison to NULL could be written "ds->ops->get_strings"
#773: FILE: net/dsa/slave.c:697:
+ if (ds->ops->get_strings != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_ethtool_stats"
#824: FILE: net/dsa/slave.c:785:
+ if (ds->ops->get_ethtool_stats != NULL)
CHECK: Comparison to NULL could be written "ds->ops->get_sset_count"
#835: FILE: net/dsa/slave.c:798:
+ if (ds->ops->get_sset_count != NULL)
total: 0 errors, 0 warnings, 4 checks, 784 lines checked
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PORT_RATE_CONTROL register works differently on 88e6095/6095f/6131
in comparison to 6123/61/65, and 0x0 disables. The distinction was lost
Linux 4.1 --> 4.2
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without it, a mv88e6131 switch will not forward incoming unicast
packets to the CPU port.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPU method of accessing PHYs makes use of a timer. Make sure this
timer is deleted before unloading the driver.
Reported-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older chips only support DSA tagging on the CPU port. New devices
support both DSA and EDSA. The driver needs to tell the core the tag
protocol to use, and configure the switch for what is available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers may drive different families of switches which need
different tag protocol. Rather than hard code the tag protocol in the
driver structure, have a callback for the DSA core to call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mv88e6xxx_wait() returns a timeout, something bad has
happened. Make sure it is noticed by logging an error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
