There are several checks for AM35x devices done using
if (cpu_is_omap3517() || cpu_is_omap3505())
However, since the 3505 is just a 3517 without an SGX, the 3505 check
is redundant because cpu_is_omap3517() will always be true whenever
cpu_is_omap3505() is true. From <plat/cpu.h>:
#define cpu_is_omap3505() (cpu_is_omap3517() && !omap3_has_sgx())
Therefore, remove the redunant 3505 checks. This helps move towards
removal of SoC detection that depends on specific IP detection.
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If transceiver is attached to a MMC host of ES2.1 OMAP35xx, it seems
2.1.1.128 erratum doesn't apply and there is no data corruption,
probably because of different signal timing. The workaround for this
erratum disables multiblock reads, which causes dramatic loss of
performance (over 75% slower), so avoid it when transceiver is present.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
[paul@pwsan.com: edited commit message slightly]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=T4T+
-----END PGP SIGNATURE-----
Merge tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
Core:
* Support for MMC 4.5 Data Tag feature -- we tag REQ_META, so devices
that support Data Tag will provide increased throughput for metadata.
* Faster detection of card removal on I/O errors.
Drivers:
* dw_mmc now supports eMMC Power Off Notify, has PCI support, and
implements pre_req and post_req for asynchronous requests.
* omap_hsmmc now supports device tree.
* esdhc now has power management support.
* sdhci-tegra now supports Tegra30 devices.
* sdhci-spear now supports hibernation.
* tmio_mmc now supports using a GPIO for card detection.
* Intel PCH now supports 8-bit bus transfers.
* tag 'mmc-merge-for-3.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: sh_mmcif: simplify bitmask macros
mmc: sh_mobile_sdhi: support modular mmc-core with non-standard hotplug
mmc: sh_mobile_sdhi: add a callback for board specific init code
mmc: tmio: cosmetic: prettify the tmio_mmc_set_ios() function
mmc: sh_mobile_sdhi: do not manage PM clocks manually
mmc: tmio_mmc: remove unused sdio_irq_enabled flag
mmc: tmio_mmc: power status flag doesn't have to be exposed in platform data
mmc: sh_mobile_sdhi: pass card hotplug GPIO number to TMIO MMC
mmc: tmio_mmc: support the generic MMC GPIO card hotplug helper
mmc: tmio: calculate the native hotplug condition only once
mmc: simplify mmc_cd_gpio_request() by removing two parameters
mmc: sdhci-pci: allow 8-bit bus width for Intel PCH
mmc: sdhci: check interrupt flags in ISR again
mmc: sdhci-pci: Add MSI support
mmc: core: warn when card doesn't support HPI
mmc: davinci: Poll status for small size transfers
mmc: davinci: Eliminate spurious interrupts
mmc: omap_hsmmc: Avoid a regulator voltage change with dt
mmc: omap_hsmmc: Convert hsmmc driver to use device tree
mmc: sdhci-pci: add SDHCI_QUIRK2_HOST_OFF_CARD_ON for Medfield SDIO
...
External circuitry like level shifters may limit the maximum operation
speed of the hsmmc controller. Add a field to struct omap2_hsmmc_info
so boards can adjust the setting on demand.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Otherwise we can get the following error depending on
the compiler:
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xafe0):
Section mismatch in reference from the function omap_hsmmc_init_one()
to the function .init.text:omap_hsmmc_pdata_init()
The function omap_hsmmc_init_one() references
the function __init omap_hsmmc_pdata_init().
This is often because omap_hsmmc_init_one lacks a __init
annotation or the annotation of omap_hsmmc_pdata_init is wrong.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that omap hsmmc init is split into two functions, it's safe
to mark omap_hsmmc_init and omap_mux related functions to __init.
This basically reverts the following fixes for the case where
TWL was compiled as a module:
a98f77b (ARM: omap: fix section mismatch warning for sdp3430_twl_gpio_setup())
8930b4e (ARM: omap: fix section mismatch warnings in mux.c caused by hsmmc.c)
Additionally it fixes up the remaining section warnings for
all callers of omap_mux functions.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise omap_device_build() and omap_mux related functions
can't be marked as __init when twl is build as a module.
If a board is using GPIO pins or regulators configured by an
external chip, such as TWL PMIC on I2C bus, the board must
mark those MMC controllers as deferred. Additionally both
omap_hsmmc_init() and omap_hsmmc_late_init() must be called
by the board.
For MMC controllers using internal GPIO pins for card
detect and regulators the slots don't need to be marked
deferred. In this case calling omap_hsmmc_init() is sufficient.
Only mark the MMC slots using gpio_cd or gpio_wd as deferred
as noted by Igor Grinberg <grinberg@compulab.co.il>.
Note that this patch does not change the behaviour for
board-4430sdp.c board-omap4panda.c. These boards wrongly
rely on the omap_hsmmc.c init function callback to configure
the PMIC GPIO interrupt lines on external chip. If the PMIC
interrupt lines are not configured during init, they will
fail.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On some omaps twl4030_gpio has a callback to try to initialize
the MMC controller. If twl4030_gpio is compiled as a module,
bad things can happen because the callback function starts
calling functions that are supposed to be marked __init:
Kernel panic - not syncing: Attempted to kill the idle task!
twl4030_gpio twl4030_gpio: can't dispatch IRQs from modules
gpiochip_add: registered GPIOs 192 to 209 on device: twl4030
Unable to handle kernel paging request at virtual address b82a4c74
...
Additionally if this does not fail, warnings are produced
about trying to register the MMC multiple times.
Fix this by removing __init from omap_mux_get_by_name,
and add checks if omap2_hsmmc_init() is getting called more
than once.
Note that this will get fixed properly later on by splitting
omap2_hsmmc_init into two functions.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0xd0f0): Section mismatch in reference from the function sdp3430_twl_gpio_setup() to the function .init.text:omap2_hsmmc_init()
The function sdp3430_twl_gpio_setup() references
the function __init omap2_hsmmc_init().
This is often because sdp3430_twl_gpio_setup lacks a __init
annotation or the annotation of omap2_hsmmc_init is wrong.
sdp3430_twl_gpio_setup() is called via platform data from the
gpio-twl4030 module, which can be inserted and removed at runtime.
This makes sdp3430_twl_gpio_setup() callable at runtime, and prevents
it being marked with an __init annotation.
As it calls omap2_hsmmc_init() unconditionally, the only resolution to
this warning is to remove the __init markings from omap2_hsmmc_init()
and its called functions. This addresses the functions in hsmmc.c.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently MMC2 setup code can only enable loopback clock and
relies on reset value for boards that need to have it disabled.
This causes a problem with certain bootloaders that always enable
that clock, resulting with unwanted bootloader dependencies.
Fix this by making it disable the clock if board data says so.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc23_before_set_reg() can set MMCSDIO2ADPCLKISEL bit, which
enables internal clock for MMC2. Currently this function is also called
by code handling MMC3, and if .internal_clock is set in platform data
(by default it currently is), it will set MMCSDIO2ADPCLKISEL for MMC2
instead of MMC3 (MMC3 doesn't have such bit so nothing actually needs to
be done). This breaks 2nd SD slot on pandora.
Fix this by changing hsmmc23_before_set_reg() to only handle MMC2.
Note that this removes .remux() call for MMC3, but no board currently
needs it and it's also not called for MMC4 and MMC5.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following error message which appears
while intializing MMC1 on the AM3517 EVM base-board:
mmc0: host doesn't support card's voltages
mmc0: error -22 whilst initialising SD card
The ocr_mask, which enumerates the volatges supported by the
MMC card was not being indicated before, assuming that a separate
Vcc regulator maybe another controllable regulator driver would be
doing this. This patch statically specifies a subset of the voltages
supported by the MMC driver, which are provided by the current fixed
voltage regulator on AM3517 EVM.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Abhilash K V <abhilash.kv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Devkit8000 uses a TWL4030 pin for card detection.
Thats why the error:
_omap_mux_init_gpio: Could not set gpio192
occurs.
This patch checks that the pin is on OMAP before
calling omap_mux_init_gpio.
Signed-off-by: Thomas Weber <weber@corscience.de>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM35x MMC 2 controller has internal clock loopback setting which cannot
be utilized without this patch and thus SDIO devices connected to this
controller and depend on this setting will fail to initialize.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pm_caps field to omap2_hsmmc_info and omap_mmc_slot_data
structs, so we will be able to indicate mmc pm capabilities
in the board file.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the typo, instead it should be SDMMC1
USBC1 is not related to MMC1 I/Os
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MMC1 data line IO's are powered down in before set regulator function.
IO's should not be powered ON when regulator is OFF.
Keep the IO's in power pown mode after regulator OFF otherwise VMODE_ERROR
interrupt is generated due to mismatch in input (regulator)
voltage and MMC IO drive voltage.
Delete incorrect comments which are not applicable for OMAP4.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reported-by: Viswanath Puttagunta <vishp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove all these duplicated structures since a default one is now
available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for
MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance
with the control module programming guide. This fixes a bug where if trying to
use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be
affected by a changing SDMMC1_VDDS.
Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever
SDMMC1_VDDS ramps up/down or changes for cell protection purposes.
MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore
they can operate independently.
Signed-off-by: Bryan Buckley <bryan.buckley@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of the device init and device driver interaction with omap_device
is done using platform_device pointers. To make this more explicit,
have omap_device return a platform_device pointer instead of an
omap_device pointer.
All current users of the omap_device pointer were only using it to get
at the platform_device pointer or struct device pointer, so fixing all
of the users was trivial.
This also makes it more difficult for device init code to directly
access members of struct omap_device, and allows for easier changing
of omap_device internals.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use generic gpio call to check the validity of the gpio. Note that
this includes gpio 0 also which was missing before.
Signed-off-by: Silesh C V <silesh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
4 micro seconds is not enough for PBIAS if MMC regulator is
enabled from MMC regulator OFF.
Increase the delay for PBIAS to stabilize.
Wait for PBIAS and timeout if not.
Resolves MMC/SD failure on OMAP4
"Pbias Voltage is not same as LDO"
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.
Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modifying the device & driver name from "mmci-omap-hs" to
"omap_hsmmc".
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP2420 platform consists of mmc block as in omap1 and not the
hsmmc block as present in omap2430, omap3, omap4 platforms.
Removing all base address macro defines except keeping one for OMAP2420 and
adapting only hsmmc device registration and driver to hwmod framework.
Changes involves:
1) Remove controller reset in devices.c which is taken care of
by hwmod framework.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute.
3) Update the driver to use dev_attr to find whether controller
supports dual volt cards
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reviewed-by: Balaji T K <balajitk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Moving the definition of mux setting API from devices.c to hsmmc.c
and renaming it from "omap2_mmc_mux" to "omap_hsmmc_mux".
Also calling "omap_hsmmc_mux" from omap2_hsmmc_init.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Chris Ball <cjb@laptop.org
Cc: Tony Lindgren <tony@atomide.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 supports up to 5 MMC controllers, but only 3 of these were
initialized. MMC5 is used by wl12xx chip. So initialize MMC4 and MMC5.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together
1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pandora has TI WL1251 attached on MMC3, which is non-standard SDIO chip.
Make use MMC_QUIRK_NONSTD_SDIO to tell SDIO core about it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Kalle Valo <kvalo@adurom.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In OMAP4, MMC1 PBIAS and its associated IO is software-controlled
by CONTROL_PBIAS and CONTROL_MMC1 registers. This patch adds PBIAS
configuration for MMC1 Controller during power-ON and power-OFF
of regulator.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517 don't have the register OMAP343X_CONTROL_PBIAS_LITE and the regulators
like "vmmc", so we set a noop "set_power" function for it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.
If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers. However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.
This patch adds a platform data field to allow
that option.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode. Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Call the PM context-loss count function, now that there
is a prototype for it.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
