Removing the sysfs stubs for the Tx FIFOCFG and ATTRELI
(stashing) config registers, as these registers may only
be configured after a MAC reset, with the controller stopped
(i.e. during hw init, at probe() time). The current sysfs
stubs allow on-the-fly updates of these registers (the locking
measures are useless and only add unecessary code).
Changing these registers is discouraged. Only the default values
will be used instead.
Moreover, the stashing (ATTRELI) configuration options were
effectively disabled (didn't get to the hw anyway if changed)
because the stashing device_flags (HAS_BD_STASHING|HAS_BUF_STASHING)
were "accidentally" cleared during probe().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out gfar_hw_init() to contain all the controller hw
initialization steps for a better control of register writes,
and to significantly simplify the tangled code from gfar_probe().
This results in code size and stack usage reduction (besides
code readability).
Fix memory leak on device removal, by freeing the rx_/tx_queue
structures.
Replace custom bit swapping function with a library one (bitrev8).
Move allocation of rx_/tx_queue struct arrays before the group
structure init, because in order to assign Rx/Tx queues
to groups we need to have the queues first. This also allows
earlier bail out of gfar_probe(), in case the memory allocation
fails.
The flow control checks for maccfg1 were removed from gfar_probe(),
since flow control is disabled at probe time (priv->rx_/tx_pause_en
are 0). Redundant initializations (by 0) also removed.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does multiple things:
* add .set_csma_params and .set_frame_retries for the RF212 radio.
This should work fine with RF230, but since I have no RF230 radios to
test with, RF230 does not implement these right now
* enable TX_ARET for frame retransmission limits greater than -1
Since RF230 has no operations to change CSMA parameters or frame retry
limits, RF230 will not be able to enter TX_ARET with this patch.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A documented erratum of the RF212 chip describes that some versions of
RF212 may not be properly reset by the standard reset procedure. The
described workaround seems to not fully work either; my RF212 chips will
not correctly receive any frames unless they are taken from RX mode to
TRX_OFF and back to RX mode, effectively forcing a up-down-up-cycle.
Going to TRX_OFF and to RX without intermediate state changes at least
once fixes this.
The same transition is allowed for RF230, so simply do it all the time.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since three of the four clear channel assesment modes make use of energy
detection, provide an API to set the energy detection threshold.
Driver support for this is available in at86rf230 for the RF212 chips.
Since for these chips the minimal energy detection threshold depends on
page and channel used, add a field to struct at86rf230_local that stores
the minimal threshold. Actual ED thresholds are configured as offsets
from this value.
For RF212, setting the ED threshold will not work before a channel/page
has been set due to the dependency of energy detection in the chip and
the actual channel/page selected.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard describes four modes of clear channel assesment: "energy
above threshold", "carrier found", and the logical and/or of these two.
Support for CCA mode setting is included in the at86rf230 driver,
predicated for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Listen-before-talk is an alternative to CSMA in uncoordinated networks
and prescribed by european regulations if one wants to have a device
with radio duty cycles above 10% (or less in some bands). Add a phy
property to enable/disable LBT in the phy, including support in the
at86rf230 driver for RF212 chips.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The standard assigns channel 0 on page 2 to be 100kbps QPSK in the
868.3MHz band. Add support to the at86rf230 driver for this channel and
page, at the moment predicated only for the RF212 chip.
Per the datasheet, configurations for page 0, channels 0 to 10 and page
2, channels 0 to 10 differ only in the BPSK_QPSK bit. Support for
channels 1 to 10 is untested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the current u8 transmit_power in wpan_phy with s8 transmit_power.
The u8 field contained the actual tx power and a tolerance field,
which no physical radio every used. Adjust sysfs entries to keep
compatibility with userspace, give tolerances of +-1dB statically there.
This patch only adds support for this in the at86rf230 driver and the
RF212 chip. Configuration calculation for RF212 is also somewhat basic,
but does the job - the RF212 datasheet gives a large table with
suggested values for combinations of TX power and page/channel, if this
does not work well, we might have to copy the whole table.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IEEE802.15.4 stack assumes that a radio will never deliver
packets with a bad CRC into the stack, as required by the standard.
at86rf230 driven radios violates this assumption because of another
incompatibility: devices are required to send ACKs if requested by a
sender, but RF2xx will only send ACKs from a special receive mode that
is currently not used by the driver.
Enable this receive mode to fix both bugs. Frames with bad CRCs will not
be received at all, and ACKs will be sent if so requested.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the AT86RF2xy chips are mostly compatible, this is only a small
change to the actual driver code. The at86rf230 driver already supports the
RF212 in most places, only three small adjustments are required:
* force the initial state after P_ON to FORCE_TRX_OFF to work around a
documented erratum
* channels_supported depends on the frequency of the transceiver, and
thus is_rf212
* do early detection of chip version select an appropriate _ops struct
based on the chip version.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Shaohui, most 10G PHYs out there have a non-standard
compliant software reset sequence, eventually something much more
complex than just toggling the BMCR_RESET bit. Allow PHY driver to
implement their own soft_reset() callback to deal with that. If no
callback is provided, call into genphy_soft_reset() which makes sure the
existing behavior is kept intact.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Shaohui, this function is generic for 10/100/1000
PHYs, but 10G PHYs might have a slightly different reset sequence which
prevents most of them from using this function.
Move the BMCR_RESET based software resent sequence to
genphy_soft_reset() in preparation for allowing PHY drivers to implement
a soft_reset() callback.
Reported-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the buffer allocation in the receive path for normal packets.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the receive path a little more efficient by parameterizing the
required state rather than re-establishing that state.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This structure is redundant; get rid of it make the code little more efficient -
get rid of the unnecessary indirection.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the use of a generic timestamping phy connected
to the cpsw if CPTS support is not enabled. This also adds support
of the SIOCGMIIREG and SIOCSMIIREG, and moves handling of SIOCGMIIPHY
to the generic driver.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ether_addr_copy is smaller and faster for some architectures.
This relies on a stack frame being at least __aligned(2)
for one use of an Ethernet address on the stack.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing terminating newlines.
Convert uses of pr_info to pr_cont in bond_check_params.
Standardize upper/lower case styles.
Typo fixes, remove unnecessary parentheses and periods.
Alignment neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more current logging style.
Coalesce formats, realign arguments, drop unnecessary periods.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On success, the function netdev_alloc_skb initializes the dev field of its
result to its first argument, so this doesn't have to be done in the
calling context.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression skb,privn,e;
@@
skb = netdev_alloc_skb(privn,...);
... when strict
(
-skb->dev = privn;
|
?skb = e
)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new configuration symbol: CONFIG_BCMGENET which allows
us to build the Broadcom GENET driver and hook the driver files into the
build system.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring the port multiplexer hardware
which resides in front of the GENET Ethernet MAC controller. This allows
us to support:
- internal PHYs (using drivers/net/phy/bcm7xxx.c)
- MoCA PHYs which are an entirely separate hardware block not covered
here
- external PHYs and switches
Note that MoCA and switches are currently supported using the emulated
"fixed PHY" driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the BCMGENET main driver file which supports the
following:
- GENET hardware from V1 to V4
- support for reading the UniMAC MIB counters statistics
- support for the 5 transmit queues
- support for RX/TX checksum offload and SG
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchs adds the bcmgenet.h header file which contains all the
hardware definitions for the GENETv1 to v4 hardware blocks as well as
the driver private structure and MIB counters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:
- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)
The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM54xx register definitions are shared between BCM54xx and
BCM7xx internal PHYs for which we are adding support. Extract these
register definitions and put them in include/linux/brcmphy.h for use by
the BCM7xxx internal PHY driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MoCA PHYs are using coaxial (BNC-like) connectors, update the
transceiver port type when replying to ethtool.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently multi-channel configuration is read via the QUERY_FW_CONFIG cmd.
This method has been deprecated by the Skyhawk-R FW. Instead,
GET_PROFILE_CONFIG::port-desc must be used to query this configuration.
This patch also:
a) introduces a few macros to identify certain categories of multi-channel
configs
2) re-factors the be_cmd_set_profile_config() code to be able to read any kind
of desc (and not just the nic-desc.)
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch logs a kernel message when a HW error(SLIPORT_ERROR in Lancer and UE
in BEx/Skyhawk) is detected. The log message for BE3 was missing earlier.
This patch also refactors the code by segregating error-detection and reporting
code for Lancer and BEx/SH.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlL7RxcACgkQjTAFq1RaXHNcKACgk4Vj+1KlmWVEin8VPoJBX86m
RasAn36pSY1OszxypJOF0O1s0qO9ld5K
=383M
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.15-20140212' of git://gitorious.org/linux-can/linux-can-next
linux-can-next-for-3.15-20140212
Marc Kleine-Budde says:
====================
this is a pull request of eight patches for net-next/master.
Florian Vaussard contributed a series that merged the sja1000 of_platform
into the platform driver. The of_platform driver is finally removed.
Stephane Grosjean supplied a patch to allocate CANFD skbs. In a patch
by Uwe Kleine-König another missing copyright information was added to
a userspace header. And a patch by Yoann DI RUZZA that adds listen only
mode to the at91_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver #define's and uses ETHERSMALL macro for the minimum Ethernet frame
size for which we have a standard macro ETH_ZLEN. Use the latter instead of
the home-grown one.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_valid_name() will check the buffer length for input name, no need to
check it twice.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_set_mac_address() will check the dev->netdev_ops->ndo_set_mac_address,
so no need to check it in bond_set_mac_address().
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to mirror the local traffic from lo to eth0,
allowing setting mac address of lo to eth0 would make
the ether addresses in these packets correct, so that
we don't have to modify the ether header again.
Since usually no one cares about its mac address (all-zero),
it is safe to allow those who care to set its mac address.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respond better to a VF reset event. When a reset is signaled by the
PF, or detected by the watchdog task, prevent the watchdog from
processing admin queue requests, and schedule the reset task.
In the reset task, wait first for the reset to start, then for it to
complete, then reinit the driver.
If the reset never appears to complete after a long, long time (>10
seconds is possible depending on what's going on with the PF driver),
then set a flag to indicate that PF communications have failed.
If this flag is set, check for the reset to complete in the watchdog,
and attempt to do a full reinitialization of the driver from scratch.
With these changes the VF driver correctly handles a PF reset event
while running on bare metal, or in a VM.
Also update copyrights.
Change-ID: I93513efd0b50523a8345e7f6a33a5e4f8a2a5996
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Dan Carpenter (from Oracle), the flags variable is
declared as a 64-bit long but all of the flags are defined as u32,
which may lead to unintended consequences. Fix this by declaring flags
as u32 (since we don't need any more than about a dozen flags right
now), and remove the volatile qualifier, since it's unnecessary and
just makes checkpatch cry.
Change-ID: I137d3bb1842bf7e9456b5929ca54e3b0ed45dcab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we store the traffic vector names in the queue vector struct, we
don't need to maintain an array of strings for these names in the
adapter structure. Replace this array with a single string and use it
when allocating the misc irq vector.
Also update copyrights.
Change-ID: I664f096c3c008210d6a04a487163e8aa934fee5b
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locate the structure in the correct header file.
Change-ID: Ic7853131728812093a44a75d6b70953311a48dab
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a bunch of unused structure members that are just wasting
space. Remove a completely unused info structure definition as well.
Also update copyrights.
Change-ID: I028ab92d9b7bd13a832cf3363bd1dc6610d8a535
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
