WARNING: With this change it is impossible to load external built
controllers anymore.
In case where CONFIG_NETPRIO_CGROUP=m and CONFIG_NET_CLS_CGROUP=m is
set, corresponding subsys_id should also be a constant. Up to now,
net_prio_subsys_id and net_cls_subsys_id would be of the type int and
the value would be assigned during runtime.
By switching the macro definition IS_SUBSYS_ENABLED from IS_BUILTIN
to IS_ENABLED, all *_subsys_id will have constant value. That means we
need to remove all the code which assumes a value can be assigned to
net_prio_subsys_id and net_cls_subsys_id.
A close look is necessary on the RCU part which was introduces by
following patch:
commit f845172531
Author: Herbert Xu <herbert@gondor.apana.org.au> Mon May 24 09:12:34 2010
Committer: David S. Miller <davem@davemloft.net> Mon May 24 09:12:34 2010
cls_cgroup: Store classid in struct sock
Tis code was added to init_cgroup_cls()
/* We can't use rcu_assign_pointer because this is an int. */
smp_wmb();
net_cls_subsys_id = net_cls_subsys.subsys_id;
respectively to exit_cgroup_cls()
net_cls_subsys_id = -1;
synchronize_rcu();
and in module version of task_cls_classid()
rcu_read_lock();
id = rcu_dereference(net_cls_subsys_id);
if (id >= 0)
classid = container_of(task_subsys_state(p, id),
struct cgroup_cls_state, css)->classid;
rcu_read_unlock();
Without an explicit explaination why the RCU part is needed. (The
rcu_deference was fixed by exchanging it to rcu_derefence_index_check()
in a later commit, but that is a minor detail.)
So here is my pondering why it was introduced and why it safe to
remove it now. Note that this code was copied over to net_prio the
reasoning holds for that subsystem too.
The idea behind the RCU use for net_cls_subsys_id is to make sure we
get a valid pointer back from task_subsys_state(). task_subsys_state()
is just blindly accessing the subsys array and returning the
pointer. Obviously, passing in -1 as id into task_subsys_state()
returns an invalid value (out of lower bound).
So this code makes sure that only after module is loaded and the
subsystem registered, the id is assigned.
Before unregistering the module all old readers must have left the
critical section. This is done by assigning -1 to the id and issuing a
synchronized_rcu(). Any new readers wont call task_subsys_state()
anymore and therefore it is safe to unregister the subsystem.
The new code relies on the same trick, but it looks at the subsys
pointer return by task_subsys_state() (remember the id is constant
and therefore we allways have a valid index into the subsys
array).
No precautions need to be taken during module loading
module. Eventually, all CPUs will get a valid pointer back from
task_subsys_state() because rebind_subsystem() which is called after
the module init() function will assigned subsys[net_cls_subsys_id] the
newly loaded module subsystem pointer.
When the subsystem is about to be removed, rebind_subsystem() will
called before the module exit() function. In this case,
rebind_subsys() will assign subsys[net_cls_subsys_id] a NULL pointer
and then it calls synchronize_rcu(). All old readers have left by then
the critical section. Any new reader wont access the subsystem
anymore. At this point we are safe to unregister the subsystem. No
synchronize_rcu() call is needed.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
task_netprioidx() should not be defined in case the configuration is
CONFIG_NETPRIO_CGROUP=n. The reason is that in a following patch the
net_prio_subsys_id will only be defined if CONFIG_NETPRIO_CGROUP!=n.
When net_prio is not built at all any callee should only get an empty
task_netprioidx() without any references to net_prio_subsys_id.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
task_cls_classid() should not be defined in case the configuration is
CONFIG_NET_CLS_CGROUP=n. The reason is that in a following patch the
net_cls_subsys_id will only be defined if CONFIG_NET_CLS_CGROUP!=n.
When net_cls is not built at all a callee should only get an empty
task_cls_classid() without any references to net_cls_subsys_id.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
The only user of sock_update_classid() is net/socket.c which happens
to include cls_cgroup.h directly.
tj: Fix build breakage due to missing cls_cgroup.h inclusion in
drivers/net/tun.c reported in linux-next by Stephen.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Gao feng <gaofeng@cn.fujitsu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: netdev@vger.kernel.org
Cc: cgroups@vger.kernel.org
It is a frequent mistake to confuse the netlink port identifier with a
process identifier. Try to reduce this confusion by renaming fields
that hold port identifiers portid instead of pid.
I have carefully avoided changing the structures exported to
userspace to avoid changing the userspace API.
I have successfully built an allyesconfig kernel with this change.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark keys that might be used to receive management
frames so drivers can fall back on software crypto
for them if they don't support hardware offload.
As the new flag is only set correctly for RX keys
and the existing IEEE80211_KEY_FLAG_SW_MGMT flag
can only affect TX, also rename the latter to
IEEE80211_KEY_FLAG_SW_MGMT_TX.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return code is not needed in hci_chan_del
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
hdev is allocated with kzalloc so zero initialization is not needed.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Since route cache deletion (89aef8921b), delay is no
more used. Remove it.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing uids and gids on NETLINK_CB from a process in one user
namespace to a process in another user namespace can result in the
wrong uid or gid being presented to userspace. Avoid that problem by
passing kuids and kgids instead.
- define struct scm_creds for use in scm_cookie and netlink_skb_parms
that holds uid and gid information in kuid_t and kgid_t.
- Modify scm_set_cred to fill out scm_creds by heand instead of using
cred_to_ucred to fill out struct ucred. This conversion ensures
userspace does not get incorrect uid or gid values to look at.
- Modify scm_recv to convert from struct scm_creds to struct ucred
before copying credential values to userspace.
- Modify __scm_send to populate struct scm_creds on in the scm_cookie,
instead of just copying struct ucred from userspace.
- Modify netlink_sendmsg to copy scm_creds instead of struct ucred
into the NETLINK_CB.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull these fixes intended for 3.6. There are more commits
here than I would like -- I got a bit behind while I was stalking
Steven Rostedt in San Diego last week... I'll slow it down after this!
There are a couple of pulls here. One is from Johannes:
"Please pull (according to the below information) to get a few fixes.
* a fix to properly disconnect in the driver when authentication or
association fails
* a fix to prevent invalid information about mesh paths being reported
to userspace
* a memory leak fix in an nl80211 error path"
The other comes via Gustavo:
"A few updates for the 3.6 kernel. There are two btusb patches to add
more supported devices through the new USB_VENDOR_AND_INTEFACE_INFO()
macro and another one that add a new device id for a Sony Vaio laptop,
one fix for a user-after-free and, finally, two patches from Vinicius
to fix a issue in SMP pairing."
Along with those...
Arend van Spriel provides a fix for a use-after-free bug in brcmfmac.
Daniel Drake avoids a hang by not trying to touch the libertas hardware
duing suspend if it is already powered-down.
Felix Fietkau provides a batch of ath9k fixes that adress some
potential problems with power settings, as well as a fix to avoid a
potential interrupt storm.
Gertjan van Wingerde provides a register-width fix for rt2x00, and
a rt2x00 fix to prevent incorrectly detecting the rfkill status.
He also provides a device ID patch.
Hante Meuleman gives us three brcmfmac fixes, one that properly
initializes a command structure, one that fixes a race condition that
could lose usb requests, and one that removes some log spam.
Marc Kleine-Budde offers an rt2x00 fix for a voltage setting on some
specific devices.
Mohammed Shafi Shajakhan sent an ath9k fix to avoid a crash related to
using timers that aren't allocated when 2 wire bluetooth coexistence
hardware is in use.
Sergei Poselenov changes rt2800usb to do some validity checking for
received packets, avoiding crashes on an ARM Soc.
Stone Piao gives us an mwifiex fix for an incorrectly set skb length
value for a command buffer.
All of these are localized to their specific drivers, and relatively
small. The power-related patches from Felix are bigger than I would
like, but I merged them in consideration of their isolation to ath9k
and the sensitive nature of power settings in wireless devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in mac80211.git to let the next patch apply
without conflicts, also resolving a hwsim conflict.
Conflicts:
drivers/net/wireless/mac80211_hwsim.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding a blackhole or a prohibit route, they were handling like classic
routes. Moreover, it was only possible to add this kind of routes by specifying
an interface.
Bug already reported here:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=498498
Before the patch:
$ ip route add blackhole 2001::1/128
RTNETLINK answers: No such device
$ ip route add blackhole 2001::1/128 dev eth0
$ ip -6 route | grep 2001
2001::1 dev eth0 metric 1024
After:
$ ip route add blackhole 2001::1/128
$ ip -6 route | grep 2001
blackhole 2001::1 dev lo metric 1024 error -22
v2: wrong patch
v3: add a field fc_type in struct fib6_config to store RTN_* type
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ESN for esp is defined in RFC 4303. This RFC assumes that the
sequence number counters are always up to date. However,
this is not true if an async crypto algorithm is employed.
If the sequence number counters are not up to date on sequence
number check, we may incorrectly update the upper 32 bit of
the sequence number. This leads to a DOS.
We workaround this by comparing the upper sequence number,
(used for authentication) with the upper sequence number
computed after the async processing. We drop the packet
if these numbers are different.
To do this, we introduce a recheck function that does this
check in the ESN case.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use proportional rate reduction (PRR) algorithm to reduce cwnd in CWR state,
in addition to Recovery state. Retire the current rate-halving in CWR.
When losses are detected via ACKs in CWR state, the sender enters Recovery
state but the cwnd reduction continues and does not restart.
Rename and refactor cwnd reduction functions since both CWR and Recovery
use the same algorithm:
tcp_init_cwnd_reduction() is new and initiates reduction state variables.
tcp_cwnd_reduction() is previously tcp_update_cwnd_in_recovery().
tcp_ends_cwnd_reduction() is previously tcp_complete_cwr().
The rate halving functions and logic such as tcp_cwnd_down(), tcp_min_cwnd(),
and the cwnd moderation inside tcp_enter_cwr() are removed. The unused
parameter, flag, in tcp_cwnd_reduction() is also removed.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the new nf_ct_timeout_lookup function to encapsulate
the timeout policy attachment that is called in the nf_conntrack_in
path.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch builds on top of the previous patch to add the support
for TFO listeners. This includes -
1. allocating, properly initializing, and managing the per listener
fastopen_queue structure when TFO is enabled
2. changes to the inet_csk_accept code to support TFO. E.g., the
request_sock can no longer be freed upon accept(), not until 3WHS
finishes
3. allowing a TCP_SYN_RECV socket to properly poll() and sendmsg()
if it's a TFO socket
4. properly closing a TFO listener, and a TFO socket before 3WHS
finishes
5. supporting TCP_FASTOPEN socket option
6. modifying tcp_check_req() to use to check a TFO socket as well
as request_sock
7. supporting TCP's TFO cookie option
8. adding a new SYN-ACK retransmit handler to use the timer directly
off the TFO socket rather than the listener socket. Note that TFO
server side will not retransmit anything other than SYN-ACK until
the 3WHS is completed.
The patch also contains an important function
"reqsk_fastopen_remove()" to manage the somewhat complex relation
between a listener, its request_sock, and the corresponding child
socket. See the comment above the function for the detail.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds all the necessary data structure and support
functions to implement TFO server side. It also documents a number
of flags for the sysctl_tcp_fastopen knob, and adds a few Linux
extension MIBs.
In addition, it includes the following:
1. a new TCP_FASTOPEN socket option an application must call to
supply a max backlog allowed in order to enable TFO on its listener.
2. A number of key data structures:
"fastopen_rsk" in tcp_sock - for a big socket to access its
request_sock for retransmission and ack processing purpose. It is
non-NULL iff 3WHS not completed.
"fastopenq" in request_sock_queue - points to a per Fast Open
listener data structure "fastopen_queue" to keep track of qlen (# of
outstanding Fast Open requests) and max_qlen, among other things.
"listener" in tcp_request_sock - to point to the original listener
for book-keeping purpose, i.e., to maintain qlen against max_qlen
as part of defense against IP spoofing attack.
3. various data structure and functions, many in tcp_fastopen.c, to
support server side Fast Open cookie operations, including
/proc/sys/net/ipv4/tcp_fastopen_key to allow manual rekeying.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9ad7c049 ("tcp: RFC2988bis + taking RTT sample from 3WHS for
the passive open side") changed the initRTO from 3secs to 1sec in
accordance to RFC6298 (former RFC2988bis). This reduced the time till
the last SYN retransmission packet gets sent from 93secs to 31secs.
RFC1122 is stating that the retransmission should be done for at least 3
minutes, but this seems to be quite high.
"However, the values of R1 and R2 may be different for SYN
and data segments. In particular, R2 for a SYN segment MUST
be set large enough to provide retransmission of the segment
for at least 3 minutes. The application can close the
connection (i.e., give up on the open attempt) sooner, of
course."
This patch increases the value of TCP_SYN_RETRIES to the value of 6,
providing a retransmission window of 63secs.
The comments for SYN and SYNACK retries have also been updated to
describe the current settings. The same goes for the documentation file
"Documentation/networking/ip-sysctl.txt".
Signed-off-by: Alexander Bergmann <alex@linlab.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the 'net' tree to get the recent set of netfilter bug fixes in
order to assist with some merge hassles Pablo is going to have to deal
with for upcoming changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing code assumes that del_timer returns true for alive conntrack
entries. However, this is not true if reliable events are enabled.
In that case, del_timer may return true for entries that were
just inserted in the dying list. Note that packets / ctnetlink may
hold references to conntrack entries that were just inserted to such
list.
This patch fixes the issue by adding an independent timer for
event delivery. This increases the size of the ecache extension.
Still we can revisit this later and use variable size extensions
to allocate this area on demand.
Tested-by: Oliver Smith <olipro@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add inet_proto_csum_replace16 for incrementally updating IPv6 pseudo header
checksums for IPv6 NAT.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: David S. Miller <davem@davemloft.net>
Convert the IPv4 NAT implementation to a protocol independent core and
address family specific modules.
Signed-off-by: Patrick McHardy <kaber@trash.net>
For mangling IPv6 packets the protocol header offset needs to be known
by the NAT packet mangling functions. Add a so far unused protoff argument
and convert the conntrack and NAT helpers to use it in preparation of
IPv6 NAT.
Signed-off-by: Patrick McHardy <kaber@trash.net>
To make it clear that it may be called from contexts that may not have
any knowledge of L2CAP, we change the connection parameter, to receive
a hci_conn.
This also makes it clear that it is checking the security of the link.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
IPv4 conntrack defragments incoming packet at the PRE_ROUTING hook and
(in case of forwarded packets) refragments them at POST_ROUTING
independent of the IP_DF flag. Refragmentation uses the dst_mtu() of
the local route without caring about the original fragment sizes,
thereby breaking PMTUD.
This patch fixes this by keeping track of the largest received fragment
with IP_DF set and generates an ICMP fragmentation required error during
refragmentation if that size exceeds the MTU.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
This is an initial merge in of Eric Biederman's work to start adding
user namespace support to the networking.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a broken build due to a missing header:
...
CC net/ipv4/proc.o
In file included from include/net/net_namespace.h:15,
from net/ipv4/proc.c:35:
include/net/netns/packet.h:11: error: field 'sklist_lock' has incomplete type
...
The lock of netns_packet has been replaced by a recent patch to be a mutex instead of a spinlock,
but we need to replace the header file to be linux/mutex.h instead of linux/spinlock.h as well.
See commit 0fa7fa98db:
packet: Protect packet sk list with mutex (v2) patch,
Signed-off-by: Rami Rosen <rosenr@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change since v1:
* Fixed inuse counters access spotted by Eric
In patch eea68e2f (packet: Report socket mclist info via diag module) I've
introduced a "scheduling in atomic" problem in packet diag module -- the
socket list is traversed under rcu_read_lock() while performed under it sk
mclist access requires rtnl lock (i.e. -- mutex) to be taken.
[152363.820563] BUG: scheduling while atomic: crtools/12517/0x10000002
[152363.820573] 4 locks held by crtools/12517:
[152363.820581] #0: (sock_diag_mutex){+.+.+.}, at: [<ffffffff81a2dcb5>] sock_diag_rcv+0x1f/0x3e
[152363.820613] #1: (sock_diag_table_mutex){+.+.+.}, at: [<ffffffff81a2de70>] sock_diag_rcv_msg+0xdb/0x11a
[152363.820644] #2: (nlk->cb_mutex){+.+.+.}, at: [<ffffffff81a67d01>] netlink_dump+0x23/0x1ab
[152363.820693] #3: (rcu_read_lock){.+.+..}, at: [<ffffffff81b6a049>] packet_diag_dump+0x0/0x1af
Similar thing was then re-introduced by further packet diag patches (fanount
mutex and pgvec mutex for rings) :(
Apart from being terribly sorry for the above, I propose to change the packet
sk list protection from spinlock to mutex. This lock currently protects two
modifications:
* sklist
* prot inuse counters
The sklist modifications can be just reprotected with mutex since they already
occur in a sleeping context. The inuse counters modifications are trickier -- the
__this_cpu_-s are used inside, thus requiring the caller to handle the potential
issues with contexts himself. Since packet sockets' counters are modified in two
places only (packet_create and packet_release) we only need to protect the context
from being preempted. BH disabling is not required in this case.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
This is the first batch of Netfilter and IPVS updates for your
net-next tree. Mostly cleanups for the Netfilter side. They are:
* Remove unnecessary RTNL locking now that we have support
for namespace in nf_conntrack, from Patrick McHardy.
* Cleanup to eliminate unnecessary goto in the initialization
path of several Netfilter tables, from Jean Sacren.
* Another cleanup from Wu Fengguang, this time to PTR_RET instead
of if IS_ERR then return PTR_ERR.
* Use list_for_each_entry_continue_rcu in nf_iterate, from
Michael Wang.
* Add pmtu_disc sysctl option to disable PMTU in their tunneling
transmitter, from Julian Anastasov.
* Generalize application protocol registration in IPVS and modify
IPVS FTP helper to use it, from Julian Anastasov.
* update Kconfig. The IPVS FTP helper depends on the Netfilter FTP
helper for NAT support, from Julian Anastasov.
* Add logic to update PMTU for IPIP packets in IPVS, again
from Julian Anastasov.
* A couple of sparse warning fixes for IPVS and Netfilter from
Claudiu Ghioc and Patrick McHardy respectively.
Patrick's IPv6 NAT changes will follow after this batch, I need
to flush this batch first before refreshing my tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso discovered that avahi and
potentially NetworkManager accept spoofed Netlink messages because of a
kernel bug. The kernel passes all-zero SCM_CREDENTIALS ancillary data
to the receiver if the sender did not provide such data, instead of not
including any such data at all or including the correct data from the
peer (as it is the case with AF_UNIX).
This bug was introduced in commit 16e5726269
(af_unix: dont send SCM_CREDENTIALS by default)
This patch forces passing credentials for netlink, as
before the regression.
Another fix would be to not add SCM_CREDENTIALS in
netlink messages if not provided by the sender, but it
might break some programs.
With help from Florian Weimer & Petr Matousek
This issue is designated as CVE-2012-3520
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the struct l2cap_chan and associated code to use
kref api for object refcounting and freeing.
Suggested-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
MGMT_EV_DEVICE_DISCONNECTED will now expose the disconnection reason to
userland, distinguishing four possible values:
0x00 Reason not known or unspecified
0x01 Connection timeout
0x02 Connection terminated by local host
0x03 Connection terminated by remote host
Note that the local/remote distinction just determines which side
terminated the low-level connection, regardless of the disconnection of
the higher-level profiles.
This can sometimes be misleading and thus must be used with care. For
example, some hardware combinations would report a locally initiated
disconnection even if the user turned Bluetooth off in the remote side.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add more HCI error codes as defined in the specification.
Signed-off-by: Mikel Astiz <mikel.astiz@bmw-carit.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Some devices like the current iwlwifi implementation
require that the P2P interface address match the P2P
Device address (only one P2P interface is supported.)
Add the HW flag IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
that allows drivers to request that P2P Interfaces
added while a P2P Device is active get the same MAC
address by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.
This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.
Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.
As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support getting A-MPDU status information from the
drivers and reporting it to userspace via radiotap
in the standard fields.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define the A-MPDU status field in radiotap, also
update the radiotap parser for it and the MCS field
that was apparently missed last time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In IBSS it is possible that the supported rates set for a station changes over
time (e.g. it gets first initialised as an empty set because of no available
information about rates and updated later). In this case the driver has to be
notified about the change in order to update its internal table accordingly (if
needed).
This behaviour is needed by all those drivers that handle rc internally but
leave stations management to mac80211
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
[Johannes - add docs, validate IBSS mode only, fix compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
This is a batch of updates intended for 3.7. The ath9k, mwifiex,
and b43 drivers get the bulk of the commits this time, with a handful
of other driver bits thrown-in. It is mostly just minor fixes and
cleanups, etc.
Also included is a Bluetooth pull, with a lot of refactoring.
Gustavo says:
"These are the changes I queued for 3.7. There are a many
small fixes/improvements by Andre Guedes. A l2cap channel
refcounting refactor by Jaganath. Bluetooth sockets now
appears in /proc/net, by Masatake Yamato and Sachin Kamat
changes ours drivers to use devm_kzalloc()."
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sematically speaking, xfrm_mgr.acquire is called when kernel intends to ask
user space IKE daemon to negotiate SAs with peers. IOW the direction will
*always* be XFRM_POLICY_OUT, so remove int dir for clarity.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I got the following compile error:
In file included from include/net/sctp/checksum.h:46:0,
from net/ipv4/netfilter/nf_nat_proto_sctp.c:14:
include/net/sctp/sctp.h: In function ‘sctp_dbg_objcnt_init’:
include/net/sctp/sctp.h:370:88: error: parameter name omitted
include/net/sctp/sctp.h: In function ‘sctp_dbg_objcnt_exit’:
include/net/sctp/sctp.h:371:88: error: parameter name omitted
which is caused by
commit 13d782f6b4
Author: Eric W. Biederman <ebiederm@xmission.com>
Date: Mon Aug 6 08:45:15 2012 +0000
sctp: Make the proc files per network namespace.
This patch could fix it.
Cc: David S. Miller <davem@davemloft.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add struct net as a parameter to sctp_verify_param so it can be passed
to sctp_verify_ext_param where struct net will be needed when the sctp
tunables become per net tunables.
Add struct net as a parameter to sctp_verify_init so struct net can be
passed to sctp_verify_param.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a handle of state machine functions primarily those dealing
with processing INIT packets where there is neither a valid endpoint nor
a valid assoication from which to derive a struct net. Therefore add
struct net * to the parameter list of sctp_state_fn_t and update all of
the state machine functions.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct net will be needed shortly when the tunables are made per network
namespace.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trickles up through sctp_sm_lookup_event up to sctp_do_sm
and up further into sctp_primitiv_NAME before the code reaches
places where struct net can be reliably found.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start with an empty sctp_net_table that will be populated as the various
tunable sysctls are made per net.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Convert all of the files under /proc/net/sctp to be per
network namespace.
- Don't print anything for /proc/net/sctp/snmp except in
the initial network namespaces as the snmp counters still
have to be converted to be per network namespace.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Kill sctp_get_ctl_sock, it is useless now.
- Pass struct net where needed so net->sctp.ctl_sock is accessible.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Move the address lists into struct net
- Add per network namespace initialization and cleanup
- Pass around struct net so it is everywhere I need it.
- Rename all of the global variable references into references
to the variables moved into struct net
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use struct net in the hash calculation
- Use sock_net(association.base.sk) in the association lookups.
- On receive calculate the network namespace from skb->dev.
- Pass struct net from receive down to the functions that actually
do the association lookup.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use struct net in the hash calculation
- Use sock_net(endpoint.base.sk) in the endpoint lookups.
- On receive calculate the network namespace from skb->dev.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add struct net into the port hash table hash calculation
- Add struct net inot the struct sctp_bind_bucket so there
is a memory of which network namespace a port is allocated in.
No need for a ref count because sctp_bind_bucket only exists
when there are sockets in the hash table and sockets can not
change their network namspace, and sockets already ref count
their network namespace.
- Add struct net into the key comparison when we are testing
to see if we have found the port hash table entry we are
looking for.
With these changes lookups in the port hash table becomes
safe to use in multiple network namespaces.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cls_flow.c plays with uids and gids. Unless I misread that
code it is possible for classifiers to depend on the specific uid and
gid values. Therefore I need to know the user namespace of the
netlink socket that is installing the packet classifiers. Pass
in the rtnetlink skb so I can access the NETLINK_CB of the passed
packet. In particular I want access to sk_user_ns(NETLINK_CB(in_skb).ssk).
Pass in not the user namespace but the incomming rtnetlink skb into
the the classifier change routines as that is generally the more useful
parameter.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Add a helper sk_user_ns to make it easy to find the user namespace
of the process that opened a socket.
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Correct a long standing omission and use struct pid in the owner
field of struct ip6_flowlabel when the share type is IPV6_FL_S_PROCESS.
This guarantees we don't have issues when pid wraparound occurs.
Use a kuid_t in the owner field of struct ip6_flowlabel when the
share type is IPV6_FL_S_USER to add user namespace support.
In /proc/net/ip6_flowlabel capture the current pid namespace when
opening the file and release the pid namespace when the file is
closed ensuring we print the pid owner value that is meaning to
the reader of the file. Similarly use from_kuid_munged to print
uid values that are meaningful to the reader of the file.
This requires exporting pid_nr_ns so that ipv6 can continue to built
as a module. Yoiks what silliness
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
- Store sysctl_ping_group_range as a paire of kgid_t values
instead of a pair of gid_t values.
- Move the kgid conversion work from ping_init_sock into ipv4_ping_group_range
- For invalid cases reset to the default disabled state.
With the kgid_t conversion made part of the original value sanitation
from userspace understand how the code will react becomes clearer
and it becomes possible to set the sysctl ping group range from
something other than the initial user namespace.
Cc: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Some connection related functions are only used inside hci_conn.c
so no need to have them exported.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
llc_station_init() creates and processes an event skb with no effect
other than to change the state from DOWN to UP. Allocation failure is
reported, but then ignored by its caller, llc2_init(). Remove this
possibility by simply initialising the state as UP.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
One condition before codel_Newton_step() was not good if
we never left the dropping state for a flow. As a result
rec_inv_sqrt was 0, instead of the ~0 initial value.
codel control law was then set to a very aggressive mode, dropping
many packets before reaching 'target' and recovering from this problem.
To keep codel_vars_init() as efficient as possible, refine
the condition to make sure rec_inv_sqrt initial value is correct
Many thanks to Anton Mich for discovering the issue and suggesting
a fix.
Reported-by: Anton Mich <lp2s1h@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_send_skb() can send orphaned skb, so we must pass the net pointer to
avoid possible NULL dereference in error path.
Bug added by commit 3a7c384ffd (ipv4: tcp: unicast_sock should not
land outside of TCP stack)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling PMTU discovery can increase the output packet
rate but some users have enough resources and prefer to fragment
than to drop traffic. By default, we copy the DF bit but if
pmtu_disc is disabled we do not send FRAG_NEEDED messages anymore.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Get rid of the ftp_app pointer and allow applications
to be registered without adding fields in the netns_ipvs structure.
v2: fix coding style as suggested by Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
As pointed out, there are places, that access net->loopback_dev->ifindex
and after ifindex generation is made per-net this value becomes constant
equals 1. So go ahead and introduce the LOOPBACK_IFINDEX constant and use
it where appropriate.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Strictly speaking this is only _really_ required for checkpoint-restore to
make loopback device always have the same index.
This change appears to be safe wrt "ifindex should be unique per-system"
concept, as all the ifindex usage is either already made per net namespace
of is explicitly limited with init_net only.
There are two cool side effects of this. The first one -- ifindices of
devices in container are always small, regardless of how many containers
we've started (and re-started) so far. The second one is -- we can speed
up the loopback ifidex access as shown in the next patch.
v2: Place ifindex right after dev_base_seq : avoid two holes and use the
same cache line, dirtied in list_netdevice()/unlist_netdevice()
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric noticed, that when there will be devices with equal indices, some
hash functions that use them will become less effective as they could.
Fix this in advance by mixing the net_device address into the hash value
instead of the device index.
This is true for arp and ndisc hash fns. The netlabel, can and llc ones
are also ifindex-based, but that three are init_net-only, thus will not
be affected.
Many thanks to David and Eric for the hash32_ptr implementation!
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While investigating on network performance problems, I found this little
gem :
$ nm -v vmlinux | grep -1 dst_default_metrics
ffffffff82736540 b busy.46605
ffffffff82736560 B dst_default_metrics
ffffffff82736598 b dst_busy_list
Apparently, declaring a const array without initializer put it in
(writeable) bss section, in middle of possibly often dirtied cache
lines.
Since we really want dst_default_metrics be const to avoid any possible
false sharing and catch any buggy writes, I force a null initializer.
ffffffff818a4c20 R dst_default_metrics
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Avoid dirtying neighbour's confirmed field.
TCP workloads hits this cache line for each incoming ACK.
Lets write n->confirmed only if there is a jiffie change.
2) Optimize neigh_hh_output() for the common Ethernet case, were
hh_len is less than 16 bytes. Replace the memcpy() call
by two inlined 64bit load/stores on x86_64.
Bench results using udpflood test, with -C option (MSG_CONFIRM flag
added to sendto(), to reproduce the n->confirmed dirtying on UDP)
24 threads doing 1.000.000 UDP sendto() on dummy device, 4 runs.
before : 2.247s, 2.235s, 2.247s, 2.318s
after : 1.884s, 1.905s, 1.891s, 1.895s
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid two instructions to reload dev->nd_net->mib.ip_statistics pointer,
unsing a temp variable, in ip_rcv(), ip_output() paths for example.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 needs a cookie in dst_check() call.
We need to add rx_dst_cookie and provide a family independent
sk_rx_dst_set(sk, skb) method to properly support IPv6 TCP early demux.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check the 'Role' parameter from the LE Connection
Complete Event in order to properly set 'out' and 'link_mode'
fields from hci_conn structure.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
lsof command can tell the type of socket processes are using.
Internal lsof uses inode numbers on socket fs to resolve the type of
sockets. Files under /proc/net/, such as tcp, udp, unix, etc provides
such inode information.
Unfortunately bluetooth related protocols don't provide such inode
information. This patch series introduces /proc/net files for the protocols.
This patch against af_bluetooth.c provides facility to the implementation
of protocols. This patch extends bt_sock_list and introduces two exported
function bt_procfs_init, bt_procfs_cleanup.
The type bt_sock_list is already used in some of implementation of
protocols. bt_procfs_init prepare seq_operations which converts
protocol own bt_sock_list data to protocol own proc entry when the
entry is accessed.
What I, lsof user, need is just inode number of bluetooth
socket. However, people may want more information. The bt_procfs_init
takes a function pointer for customizing the show handler of
seq_operations.
In v4 patch, __acquires and __releases attributes are added to suppress
sparse warning. Suggested by Andrei Emeltchenko.
In v5 patch, linux/proc_fs.h is included to use PDE. Build error is
reported by Fengguang Wu.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Move the l2cap channel list chan->global_l under the refcnt
protection and free it based on the refcnt.
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Reviewed-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Refactor the code in order to use the l2cap_chan_destroy()
from l2cap_chan_put() under the refcnt protection.
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Reviewed-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Return values are never used because callers hci_proto_connect_cfm
and hci_proto_disconn_cfm return void.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
AMP status codes copied from Bluez patch sent by Peter Krystad
<pkrystad@codeaurora.org>.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Change spaces to tabs in smp code
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Use the same style for refcnt printing through all Bluetooth code
taking the reference the l2cap_chan refcnt printing.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Add check that HCI controller is BR/EDR. AMP controller shall not be
managed by mgmt interface and consequently user space.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch removes the struct adv_entry since it is not used anymore.
This struct should have been removed in commit 479453d (Bluetooth:
Remove advertising cache).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This handles the merge issue in:
arch/um/drivers/line.c
arch/um/drivers/line.h
And resolves the duplicate patches that were in both trees do to the
tty-next branch not getting merged into 3.6-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed types might be needed in NL communication from time to time
(I need s32 in team driver), so add them.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only way for wireless drivers to tell whether or not OFDM
is allowed on the current channel is to check the regulatory
information. However, this requires hodling cfg80211_mutex, which is not
visible to the drivers.
Other regulatory restrictions are provided as flags in the channel
definition, so let's do similarly with OFDM. This patch adds a new flag,
IEEE80211_CHAN_NO_OFDM, to tell drivers that OFDM on a channel is not
allowed. This flag is set on any channels for which regulatory indicates
that OFDM is prohibited.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After SA is setup, one timer is armed to detect soft/hard expiration,
however the timer handler uses xtime to do the math. This makes hard
expiration occurs first before soft expiration after setting new date
with big interval. As a result new child SA is deleted before rekeying
the new one.
Signed-off-by: Fan Du <fdu@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache the device gso_max_segs in sock::sk_gso_max_segs and use it to
limit the size of TSO skbs. This avoids the need to fall back to
software GSO for local TCP senders.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge Andrew's second set of patches:
- MM
- a few random fixes
- a couple of RTC leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (120 commits)
rtc/rtc-88pm80x: remove unneed devm_kfree
rtc/rtc-88pm80x: assign ret only when rtc_register_driver fails
mm: hugetlbfs: close race during teardown of hugetlbfs shared page tables
tmpfs: distribute interleave better across nodes
mm: remove redundant initialization
mm: warn if pg_data_t isn't initialized with zero
mips: zero out pg_data_t when it's allocated
memcg: gix memory accounting scalability in shrink_page_list
mm/sparse: remove index_init_lock
mm/sparse: more checks on mem_section number
mm/sparse: optimize sparse_index_alloc
memcg: add mem_cgroup_from_css() helper
memcg: further prevent OOM with too many dirty pages
memcg: prevent OOM with too many dirty pages
mm: mmu_notifier: fix freed page still mapped in secondary MMU
mm: memcg: only check anon swapin page charges for swap cache
mm: memcg: only check swap cache pages for repeated charging
mm: memcg: split swapin charge function into private and public part
mm: memcg: remove needless !mm fixup to init_mm when charging
mm: memcg: remove unneeded shmem charge type
...
This patch series is based on top of "Swap-over-NBD without deadlocking
v15" as it depends on the same reservation of PF_MEMALLOC reserves logic.
When a user or administrator requires swap for their application, they
create a swap partition and file, format it with mkswap and activate it
with swapon. In diskless systems this is not an option so if swap if
required then swapping over the network is considered. The two likely
scenarios are when blade servers are used as part of a cluster where the
form factor or maintenance costs do not allow the use of disks and thin
clients.
The Linux Terminal Server Project recommends the use of the Network Block
Device (NBD) for swap but this is not always an option. There is no
guarantee that the network attached storage (NAS) device is running Linux
or supports NBD. However, it is likely that it supports NFS so there are
users that want support for swapping over NFS despite any performance
concern. Some distributions currently carry patches that support swapping
over NFS but it would be preferable to support it in the mainline kernel.
Patch 1 avoids a stream-specific deadlock that potentially affects TCP.
Patch 2 is a small modification to SELinux to avoid using PFMEMALLOC
reserves.
Patch 3 adds three helpers for filesystems to handle swap cache pages.
For example, page_file_mapping() returns page->mapping for
file-backed pages and the address_space of the underlying
swap file for swap cache pages.
Patch 4 adds two address_space_operations to allow a filesystem
to pin all metadata relevant to a swapfile in memory. Upon
successful activation, the swapfile is marked SWP_FILE and
the address space operation ->direct_IO is used for writing
and ->readpage for reading in swap pages.
Patch 5 notes that patch 3 is bolting
filesystem-specific-swapfile-support onto the side and that
the default handlers have different information to what
is available to the filesystem. This patch refactors the
code so that there are generic handlers for each of the new
address_space operations.
Patch 6 adds an API to allow a vector of kernel addresses to be
translated to struct pages and pinned for IO.
Patch 7 adds support for using highmem pages for swap by kmapping
the pages before calling the direct_IO handler.
Patch 8 updates NFS to use the helpers from patch 3 where necessary.
Patch 9 avoids setting PF_private on PG_swapcache pages within NFS.
Patch 10 implements the new swapfile-related address_space operations
for NFS and teaches the direct IO handler how to manage
kernel addresses.
Patch 11 prevents page allocator recursions in NFS by using GFP_NOIO
where appropriate.
Patch 12 fixes a NULL pointer dereference that occurs when using
swap-over-NFS.
With the patches applied, it is possible to mount a swapfile that is on an
NFS filesystem. Swap performance is not great with a swap stress test
taking roughly twice as long to complete than if the swap device was
backed by NBD.
This patch: netvm: prevent a stream-specific deadlock
It could happen that all !SOCK_MEMALLOC sockets have buffered so much data
that we're over the global rmem limit. This will prevent SOCK_MEMALLOC
buffers from receiving data, which will prevent userspace from running,
which is needed to reduce the buffered data.
Fix this by exempting the SOCK_MEMALLOC sockets from the rmem limit. Once
this change it applied, it is important that sockets that set
SOCK_MEMALLOC do not clear the flag until the socket is being torn down.
If this happens, a warning is generated and the tokens reclaimed to avoid
accounting errors until the bug is fixed.
[davem@davemloft.net: Warning about clearing SOCK_MEMALLOC]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to make sure pfmemalloc packets receive all memory needed to
proceed, ensure processing of pfmemalloc SKBs happens under PF_MEMALLOC.
This is limited to a subset of protocols that are expected to be used for
writing to swap. Taps are not allowed to use PF_MEMALLOC as these are
expected to communicate with userspace processes which could be paged out.
[a.p.zijlstra@chello.nl: Ideas taken from various patches]
[jslaby@suse.cz: Lock imbalance fix]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the skb allocation API to indicate RX usage and use this to fall
back to the PFMEMALLOC reserve when needed. SKBs allocated from the
reserve are tagged in skb->pfmemalloc. If an SKB is allocated from the
reserve and the socket is later found to be unrelated to page reclaim, the
packet is dropped so that the memory remains available for page reclaim.
Network protocols are expected to recover from this packet loss.
[a.p.zijlstra@chello.nl: Ideas taken from various patches]
[davem@davemloft.net: Use static branches, coding style corrections]
[sebastian@breakpoint.cc: Avoid unnecessary cast, fix !CONFIG_NET build]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow specific sockets to be tagged SOCK_MEMALLOC and use __GFP_MEMALLOC
for their allocations. These sockets will be able to go below watermarks
and allocate from the emergency reserve. Such sockets are to be used to
service the VM (iow. to swap over). They must be handled kernel side,
exposing such a socket to user-space is a bug.
There is a risk that the reserves be depleted so for now, the
administrator is responsible for increasing min_free_kbytes as necessary
to prevent deadlock for their workloads.
[a.p.zijlstra@chello.nl: Original patches]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce sk_gfp_atomic(), this function allows to inject sock specific
flags to each sock related allocation. It is only used on allocation
paths that may be required for writing pages back to network storage.
[davem@davemloft.net: Use sk_gfp_atomic only when necessary]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a device is unregistered, we have to purge all of the
references to it that may exist in the entire system.
If a route is uncached, we currently have no way of accomplishing
this.
So create a global list that is scanned when a network device goes
down. This mirrors the logic in net/core/dst.c's dst_ifdown().
Signed-off-by: David S. Miller <davem@davemloft.net>
Input path is mostly run under RCU and doesnt touch dst refcnt
But output path on forwarding or UDP workloads hits
badly dst refcount, and we have lot of false sharing, for example
in ipv4_mtu() when reading rt->rt_pmtu
Using a percpu cache for nh_rth_output gives a nice performance
increase at a small cost.
24 udpflood test on my 24 cpu machine (dummy0 output device)
(each process sends 1.000.000 udp frames, 24 processes are started)
before : 5.24 s
after : 2.06 s
For reference, time on linux-3.5 : 6.60 s
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 404e0a8b6a (net: ipv4: fix RCU races on dst refcounts) tried
to solve a race but added a problem at device/fib dismantle time :
We really want to call dst_free() as soon as possible, even if sockets
still have dst in their cache.
dst_release() calls in free_fib_info_rcu() are not welcomed.
Root of the problem was that now we also cache output routes (in
nh_rth_output), we must use call_rcu() instead of call_rcu_bh() in
rt_free(), because output route lookups are done in process context.
Based on feedback and initial patch from David Miller (adding another
call_rcu_bh() call in fib, but it appears it was not the right fix)
I left the inet_sk_rx_dst_set() helper and added __rcu attributes
to nh_rth_output and nh_rth_input to better document what is going on in
this code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, ps mode is indicated per device (rather than
per interface), which doesn't make a lot of sense.
Moreover, there are subtle bugs caused by the inability
to indicate ps change along with other changes
(e.g. when the AP deauth us, we'd like to indicate
CHANGED_PS | CHANGED_ASSOC, as changing PS before
notifying about disassociation will result in null-packets
being sent (if IEEE80211_HW_SUPPORTS_DYNAMIC_PS) while
the sta is already disconnected.)
Keep the current per-device notifications, and add
parallel per-vif notifications.
In order to keep it simple, the per-device ps and
the per-vif ps are orthogonal - the per-vif ps
configuration is determined only by the user
configuration (enable/disable) and the connection
state, and is not affected by other vifs state and
(temporary) dynamic_ps/offchannel operations
(unlike per-device ps).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After IP route cache removal, rt_cache_rebuild_count is no longer
used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c6cffba4ff (ipv4: Fix input route performance regression.)
added various fatal races with dst refcounts.
crashes happen on tcp workloads if routes are added/deleted at the same
time.
The dst_free() calls from free_fib_info_rcu() are clearly racy.
We need instead regular dst refcounting (dst_release()) and make
sure dst_release() is aware of RCU grace periods :
Add DST_RCU_FREE flag so that dst_release() respects an RCU grace period
before dst destruction for cached dst
Introduce a new inet_sk_rx_dst_set() helper, using atomic_inc_not_zero()
to make sure we dont increase a zero refcount (On a dst currently
waiting an rcu grace period before destruction)
rt_cache_route() must take a reference on the new cached route, and
release it if was not able to install it.
With this patch, my machines survive various benchmarks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the IPv6 missing bits for infrastructure added in commit
41063e9dd1 (ipv4: Early TCP socket demux.)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the routing cache removal we lost the "noref" code paths on
input, and this can kill some routing workloads.
Reinstate the noref path when we hit a cached route in the FIB
nexthops.
With help from Eric Dumazet.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David S Miller:
1) Remove the ipv4 routing cache. Now lookups go directly into the FIB
trie and use prebuilt routes cached there.
No more garbage collection, no more rDOS attacks on the routing
cache. Instead we now get predictable and consistent performance,
no matter what the pattern of traffic we service.
This has been almost 2 years in the making. Special thanks to
Julian Anastasov, Eric Dumazet, Steffen Klassert, and others who
have helped along the way.
I'm sure that with a change of this magnitude there will be some
kind of fallout, but such things ought the be simple to fix at this
point. Luckily I'm not European so I'll be around all of August to
fix things :-)
The major stages of this work here are each fronted by a forced
merge commit whose commit message contains a top-level description
of the motivations and implementation issues.
2) Pre-demux of established ipv4 TCP sockets, saves a route demux on
input.
3) TCP SYN/ACK performance tweaks from Eric Dumazet.
4) Add namespace support for netfilter L4 conntrack helpers, from Gao
Feng.
5) Add config mechanism for Energy Efficient Ethernet to ethtool, from
Yuval Mintz.
6) Remove quadratic behavior from /proc/net/unix, from Eric Dumazet.
7) Support for connection tracker helpers in userspace, from Pablo
Neira Ayuso.
8) Allow userspace driven TX load balancing functions in TEAM driver,
from Jiri Pirko.
9) Kill off NLMSG_PUT and RTA_PUT macros, more gross stuff with
embedded gotos.
10) TCP Small Queues, essentially minimize the amount of TCP data queued
up in the packet scheduler layer. Whereas the existing BQL (Byte
Queue Limits) limits the pkt_sched --> netdevice queuing levels,
this controls the TCP --> pkt_sched queueing levels.
From Eric Dumazet.
11) Reduce the number of get_page/put_page ops done on SKB fragments,
from Alexander Duyck.
12) Implement protection against blind resets in TCP (RFC 5961), from
Eric Dumazet.
13) Support the client side of TCP Fast Open, basically the ability to
send data in the SYN exchange, from Yuchung Cheng.
Basically, the sender queues up data with a sendmsg() call using
MSG_FASTOPEN, then they do the connect() which emits the queued up
fastopen data.
14) Avoid all the problems we get into in TCP when timers or PMTU events
hit a locked socket. The TCP Small Queues changes added a
tcp_release_cb() that allows us to queue work up to the
release_sock() caller, and that's what we use here too. From Eric
Dumazet.
15) Zero copy on TX support for TUN driver, from Michael S. Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1870 commits)
genetlink: define lockdep_genl_is_held() when CONFIG_LOCKDEP
r8169: revert "add byte queue limit support".
ipv4: Change rt->rt_iif encoding.
net: Make skb->skb_iif always track skb->dev
ipv4: Prepare for change of rt->rt_iif encoding.
ipv4: Remove all RTCF_DIRECTSRC handliing.
ipv4: Really ignore ICMP address requests/replies.
decnet: Don't set RTCF_DIRECTSRC.
net/ipv4/ip_vti.c: Fix __rcu warnings detected by sparse.
ipv4: Remove redundant assignment
rds: set correct msg_namelen
openvswitch: potential NULL deref in sample()
tcp: dont drop MTU reduction indications
bnx2x: Add new 57840 device IDs
tcp: avoid oops in tcp_metrics and reset tcpm_stamp
niu: Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return value
niu: Fix to check for dma mapping errors.
net: Fix references to out-of-scope variables in put_cmsg_compat()
net: ethernet: davinci_emac: add pm_runtime support
net: ethernet: davinci_emac: Remove unnecessary #include
...
On input packet processing, rt->rt_iif will be zero if we should
use skb->dev->ifindex.
Since we access rt->rt_iif consistently via inet_iif(), that is
the only spot whose interpretation have to adjust.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use inet_iif() consistently, and for TCP record the input interface of
cached RX dst in inet sock.
rt->rt_iif is going to be encoded differently, so that we can
legitimately cache input routes in the FIB info more aggressively.
When the input interface is "use SKB device index" the rt->rt_iif will
be set to zero.
This forces us to move the TCP RX dst cache installation into the ipv4
specific code, and as well it should since doing the route caching for
ipv6 is pointless at the moment since it is not inspected in the ipv6
input paths yet.
Also, remove the unlikely on dst->obsolete, all ipv4 dsts have
obsolete set to a non-zero value to force invocation of the check
callback.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull the big VFS changes from Al Viro:
"This one is *big* and changes quite a few things around VFS. What's in there:
- the first of two really major architecture changes - death to open
intents.
The former is finally there; it was very long in making, but with
Miklos getting through really hard and messy final push in
fs/namei.c, we finally have it. Unlike his variant, this one
doesn't introduce struct opendata; what we have instead is
->atomic_open() taking preallocated struct file * and passing
everything via its fields.
Instead of returning struct file *, it returns -E... on error, 0
on success and 1 in "deal with it yourself" case (e.g. symlink
found on server, etc.).
See comments before fs/namei.c:atomic_open(). That made a lot of
goodies finally possible and quite a few are in that pile:
->lookup(), ->d_revalidate() and ->create() do not get struct
nameidata * anymore; ->lookup() and ->d_revalidate() get lookup
flags instead, ->create() gets "do we want it exclusive" flag.
With the introduction of new helper (kern_path_locked()) we are rid
of all struct nameidata instances outside of fs/namei.c; it's still
visible in namei.h, but not for long. Come the next cycle,
declaration will move either to fs/internal.h or to fs/namei.c
itself. [me, miklos, hch]
- The second major change: behaviour of final fput(). Now we have
__fput() done without any locks held by caller *and* not from deep
in call stack.
That obviously lifts a lot of constraints on the locking in there.
Moreover, it's legal now to call fput() from atomic contexts (which
has immediately simplified life for aio.c). We also don't need
anti-recursion logics in __scm_destroy() anymore.
There is a price, though - the damn thing has become partially
asynchronous. For fput() from normal process we are guaranteed
that pending __fput() will be done before the caller returns to
userland, exits or gets stopped for ptrace.
For kernel threads and atomic contexts it's done via
schedule_work(), so theoretically we might need a way to make sure
it's finished; so far only one such place had been found, but there
might be more.
There's flush_delayed_fput() (do all pending __fput()) and there's
__fput_sync() (fput() analog doing __fput() immediately). I hope
we won't need them often; see warnings in fs/file_table.c for
details. [me, based on task_work series from Oleg merged last
cycle]
- sync series from Jan
- large part of "death to sync_supers()" work from Artem; the only
bits missing here are exofs and ext4 ones. As far as I understand,
those are going via the exofs and ext4 trees resp.; once they are
in, we can put ->write_super() to the rest, along with the thread
calling it.
- preparatory bits from unionmount series (from dhowells).
- assorted cleanups and fixes all over the place, as usual.
This is not the last pile for this cycle; there's at least jlayton's
ESTALE work and fsfreeze series (the latter - in dire need of fixes,
so I'm not sure it'll make the cut this cycle). I'll probably throw
symlink/hardlink restrictions stuff from Kees into the next pile, too.
Plus there's a lot of misc patches I hadn't thrown into that one -
it's large enough as it is..."
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (127 commits)
ext4: switch EXT4_IOC_RESIZE_FS to mnt_want_write_file()
btrfs: switch btrfs_ioctl_balance() to mnt_want_write_file()
switch dentry_open() to struct path, make it grab references itself
spufs: shift dget/mntget towards dentry_open()
zoran: don't bother with struct file * in zoran_map
ecryptfs: don't reinvent the wheels, please - use struct completion
don't expose I_NEW inodes via dentry->d_inode
tidy up namei.c a bit
unobfuscate follow_up() a bit
ext3: pass custom EOF to generic_file_llseek_size()
ext4: use core vfs llseek code for dir seeks
vfs: allow custom EOF in generic_file_llseek code
vfs: Avoid unnecessary WB_SYNC_NONE writeback during sys_sync and reorder sync passes
vfs: Remove unnecessary flushing of block devices
vfs: Make sys_sync writeout also block device inodes
vfs: Create function for iterating over block devices
vfs: Reorder operations during sys_sync
quota: Move quota syncing to ->sync_fs method
quota: Split dquot_quota_sync() to writeback and cache flushing part
vfs: Move noop_backing_dev_info check from sync into writeback
...
ICMP messages generated in output path if frame length is bigger than
mtu are actually lost because socket is owned by user (doing the xmit)
One example is the ipgre_tunnel_xmit() calling
icmp_send(skb, ICMP_DEST_UNREACH, ICMP_FRAG_NEEDED, htonl(mtu));
We had a similar case fixed in commit a34a101e1e (ipv6: disable GSO on
sockets hitting dst_allfrag).
Problem of such fix is that it relied on retransmit timers, so short tcp
sessions paid a too big latency increase price.
This patch uses the tcp_release_cb() infrastructure so that MTU
reduction messages (ICMP messages) are not lost, and no extra delay
is added in TCP transmits.
Reported-by: Maciej Żenczykowski <maze@google.com>
Diagnosed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Tore Anderson <tore@fud.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 routing cache is non-deterministic, performance wise, and is
subject to reasonably easy to launch denial of service attacks.
The routing cache works great for well behaved traffic, and the world
was a much friendlier place when the tradeoffs that led to the routing
cache's design were considered.
What it boils down to is that the performance of the routing cache is
a product of the traffic patterns seen by a system rather than being a
product of the contents of the routing tables. The former of which is
controllable by external entitites.
Even for "well behaved" legitimate traffic, high volume sites can see
hit rates in the routing cache of only ~%10.
The general flow of this patch series is that first the routing cache
is removed. We build a completely new rtable entry every lookup
request.
Next we make some simplifications due to the fact that removing the
routing cache causes several members of struct rtable to become no
longer necessary.
Then we need to make some amends such that we can legally cache
pre-constructed routes in the FIB nexthops. Firstly, we need to
invalidate routes which are hit with nexthop exceptions. Secondly we
have to change the semantics of rt->rt_gateway such that zero means
that the destination is on-link and non-zero otherwise.
Now that the preparations are ready, we start caching precomputed
routes in the FIB nexthops. Output and input routes need different
kinds of care when determining if we can legally do such caching or
not. The details are in the commit log messages for those changes.
The patch series then winds down with some more struct rtable
simplifications and other tidy ups that remove unnecessary overhead.
On a SPARC-T3 output route lookups are ~876 cycles. Input route
lookups are ~1169 cycles with rpfilter disabled, and about ~1468
cycles with rpfilter enabled.
These measurements were taken with the kbench_mod test module in the
net_test_tools GIT tree:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net_test_tools.git
That GIT tree also includes a udpflood tester tool and stresses
route lookups on packet output.
For example, on the same SPARC-T3 system we can run:
time ./udpflood -l 10000000 10.2.2.11
with routing cache:
real 1m21.955s user 0m6.530s sys 1m15.390s
without routing cache:
real 1m31.678s user 0m6.520s sys 1m25.140s
Performance undoubtedly can easily be improved further.
For example fib_table_lookup() performs a lot of excessive
computations with all the masking and shifting, some of it
conditionalized to deal with edge cases.
Also, Eric's no-ref optimization for input route lookups can be
re-instated for the FIB nexthop caching code path. I would be really
pleased if someone would work on that.
In fact anyone suitable motivated can just fire up perf on the loading
of the test net_test_tools benchmark kernel module. I spend much of
my time going:
bash# perf record insmod ./kbench_mod.ko dst=172.30.42.22 src=74.128.0.1 iif=2
bash# perf report
Thanks to helpful feedback from Joe Perches, Eric Dumazet, Ben
Hutchings, and others.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of updating the sk_cgrp_prioidx struct field on every send
this only updates the field when a task is moved via cgroup
infrastructure.
This allows sockets that may be used by a kernel worker thread
to be managed. For example in the iscsi case today a user can
put iscsid in a netprio cgroup and control traffic will be sent
with the correct sk_cgrp_prioidx value set but as soon as data
is sent the kernel worker thread isssues a send and sk_cgrp_prioidx
is updated with the kernel worker threads value which is the
default case.
It seems more correct to only update the field when the user
explicitly sets it via control group infrastructure. This allows
the users to manage sockets that may be used with other threads.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've seen several attempts recently made to do quick failover of sctp transports
by reducing various retransmit timers and counters. While its possible to
implement a faster failover on multihomed sctp associations, its not
particularly robust, in that it can lead to unneeded retransmits, as well as
false connection failures due to intermittent latency on a network.
Instead, lets implement the new ietf quick failover draft found here:
http://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05
This will let the sctp stack identify transports that have had a small number of
errors, and avoid using them quickly until their reliability can be
re-established. I've tested this out on two virt guests connected via multiple
isolated virt networks and believe its in compliance with the above draft and
works well.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Sridhar Samudrala <sri@us.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
CC: joe@perches.com
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using a special key "0" for all loopback and point-to-point
device neigh lookups under ipv4, but we wouldn't use that special
key for the neigh creation.
So basically we'd make a new neigh at each and every lookup :-)
This special case to use only one neigh for these device types
is of dubious value, so just remove it entirely.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not really needed.
We only grabbed a reference to the fib_info for the sake of fib_info
local metrics.
However, fib_info objects are freed using RCU, as are therefore their
private metrics (if any).
We would have triggered a route cache flush if we eliminated a
reference to a fib_info object in the routing tables.
Therefore, any existing cached routes will first check and see that
they have been invalidated before an errant reference to these
metric values would occur.
Signed-off-by: David S. Miller <davem@davemloft.net>
That is this value's only use, as a boolean to indicate whether
a route is an input route or not.
So implement it that way, using a u16 gap present in the struct
already.
Signed-off-by: David S. Miller <davem@davemloft.net>
Never actually used.
It was being set on output routes to the original OIF specified in the
flow key used for the lookup.
Adjust the only user, ipmr_rt_fib_lookup(), for greater correctness of
the flowi4_oif and flowi4_iif values, thanks to feedback from Julian
Anastasov.
Signed-off-by: David S. Miller <davem@davemloft.net>
Caching input routes is slightly simpler than output routes, since we
don't need to be concerned with nexthop exceptions. (locally
destined, and routed packets, never trigger PMTU events or redirects
that will be processed by us).
However, we have to elide caching for the DIRECTSRC and non-zero itag
cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have an output route that lacks nexthop exceptions, we can cache
it in the FIB info nexthop.
Such routes will have DST_HOST cleared because such routes refer to a
family of destinations, rather than just one.
The sequence of the handling of exceptions during route lookup is
adjusted to make the logic work properly.
Before we allocate the route, we lookup the exception.
Then we know if we will cache this route or not, and therefore whether
DST_HOST should be set on the allocated route.
Then we use DST_HOST to key off whether we should store the resulting
route, during rt_set_nexthop(), in the FIB nexthop cache.
With help from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a big comment explaining how the field works, and use defines
instead of magic constants for the values assigned to it.
Suggested by Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow prefixed routes, we have to adjust how rt_gateway
is set and interpreted.
The new interpretation is:
1) rt_gateway == 0, destination is on-link, nexthop is iph->daddr
2) rt_gateway != 0, destination requires a nexthop gateway
Abstract the fetching of the proper nexthop value using a new
inline helper, rt_nexthop(), as suggested by Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Vijay Subramanian <subramanian.vijay@gmail.com>
