DRIVER_NAME was undefined for SmartReflex. Now it is
defined with valid value "smartreflex". It is needed
to define proper value for:
MODULE_ALIAS("platform:" DRIVER_NAME);
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Runtime PM should be disabled for device on driver remove,
otherwise runtime PM will be not balanced, and this will cause
an error message, on next driver probe.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
vpboundsintr_en is available inside the IP block as an re-sycned
version and one which is not. Due to this, there is an 1 sysclk
cycle window where the SR_SInterruptz signal could be asserted low.
IF, intr_en is cleared on the exact same cycle as the irqclr, an
additional pulse is generated which indicates for VP that
an additional adjustment of voltage is required.
This results in VP doing two voltage adjustments for the SRERR
(based on configuration, upto 4 steps), instead of the needed
1 step.
Due to the unexpected pulse from AVS which breaks the AVS-VP
communication protocol, VP also ends up in a stuck condition by
entering a state where VP module remains non-responsive
to any futher AVS adjustment events. This creates the symptom
called "TRANXDONE Timeout" scenario.
By disabling errgen prior to disable of intr_en, this situation
can be avoided.
Signed-off-by: Vincent Bour <v-bour@ti.com>
Signed-off-by: Leonardo Affortunati <l-affortunati@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The cpu_is_omap macros are now local to arch/arm/mach-omap2
in soc.h and plat/cpu.h can finally be dropped for omap2+.
Thanks everybody for help with fixing the drivers.
Note that we can now also remove the unused plat/cpu.h from
smartreflex.c and isp.c as they will cause compile errors
with ARCH_MULTIPLATFORM enabled.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Jean Pihet <jean.pihet@newoldbits.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h2Qo
-----END PGP SIGNATURE-----
Merge tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the device dependent code (ex. cpu_is_xxx()) and settings
from the driver code and instead pass them via the platform
data. This allows a clean separation of the driver code and the platform
code, as required by the move of the platform header files to
include/linux/platform_data.
Note about the smartreflex functional clocks: the smartreflex fclks
are derived from sys_clk and have the same name as the main_clk from
the hwmod entry, in order for the SmartReflex driver to request the
fclk (using clk_get(dev, "fck")).
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Fix the error handling path in omap_sr_probe to correctly
de-allocate resources in case of problems.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove hardcoded IRQs in irqs.h and related files as these
are no longer needed.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Disable the module option for POWER_AVS since this is currently not
supported.
This patch fixes these error in the case POWER_AVS is set to 'm':
arch/arm/mach-omap2/built-in.o: In function `sr_class3_configure':
arch/arm/mach-omap2/smartreflex-class3.c:43: undefined reference to `sr_configure_errgen'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_disable':
arch/arm/mach-omap2/smartreflex-class3.c:33: undefined reference to `sr_disable_errgen'
arch/arm/mach-omap2/smartreflex-class3.c:35: undefined reference to `sr_disable'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_enable':
arch/arm/mach-omap2/smartreflex-class3.c:28: undefined reference to `sr_enable'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_init':
arch/arm/mach-omap2/smartreflex-class3.c:59: undefined reference to `sr_register_class'
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated to use relative paths for the build error]
Signed-off-by: Tony Lindgren <tony@atomide.com>
After a clean-up of the interfaces the OMAP Smartreflex IP driver is now a
generic driver. Move it to drivers/power/avs/.
The build is controlled by the following Kconfig options:
. CONFIG_POWER_AVS: general knob for Adaptive Voltage Scaling support,
. CONFIG_POWER_AVS_OMAP: AVS(Adaptive Voltage Scaling)
support on OMAP containing the version 1 or version 2 of the SmartReflex IP,
. CONFIG_POWER_AVS_OMAP_CLASS3: Class 3 implementation of Smartreflex.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
