In order to allow wake support in STOP sleep mode, clocks are needed. Use
imx_clk_gate2_cgr to disable automatic clock gating in low power mode STOP.
This allows to enable wake by UART using:
echo enabled > /sys/class/tty/ttyLP0/power/wakeup
However, if wake is not enabled, the driver should disable the clocks explicitly
to save power.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160628053235.5114-3-bhuvanchandra.dv@toradex.com
Add the ipg (bus) clock for the TCON modules (Timing Controller). This
module is required by the new DCU DRM driver, since the display signals
pass through TCON.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Similar to an earlier fix for the SAI clocks, the DCU clock hierarchy
mixes the bus clock with the display controllers pixel clock. Tests
have shown that the gates in CCM_CCGR3/9 registers do not control
the DCU pixel clock, but only the register access clock (bus clock).
Fix this by defining the parent clock of VF610_CLK_DCUx to be the bus
clock (ipg_bus).
Since the clock has not been used far, there are no further changes
needed.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock register are lost when enterying LPSTOPx, hence provide
suspend/resume functions restoring them. The clock gates get
restored by the individual driver, hence we do not need to restore
them here.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To use STOP mode without putting DDR3 into self-refresh mode, we
need to keep the DDR clock enabled. Use the new gate configuration
with a value of 2 to make sure that the clock is enabled in RUN,
WAIT and STOP mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Synchronous Audio Interface (SAI) instances are clocked by
independent clocks: The bus clock and the audio clock (as shown in
Figure 51-1 in the Vybrid Reference Manual). The clock gates in
CCGR0/CCGR1 for SAI0 through SAI3 are bus clock gates, as access
tests to the registers with/without gating those clocks have shown.
The audio clock is gated by the SAIx_EN gates in CCM_CSCDR1,
followed by a clock divider (SAIx_DIV). Currently, the parent of
the bus clock gates has been assigned to SAIx_DIV, which is not
involved in the bus clock path for the SAI instances (see chapter
9.10.12, SAI clocking in the Vybrid Reference Manual).
Fix this by define the parent clock of VF610_CLK_SAIx to be the bus
clock.
If the driver needs the audio clock (when used in master mode), a
fixed device tree is required which assign the audio clock properly
to VF610_CLK_SAIx_DIV.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add clock support for Vybrid On-Chip One Time Programmable
(OCOTP) controller.
While the OCOTP block does not require explicit clock gating,
for programming the OCOTP timing register the clock rate of
ipg clock is required for timing calculations related to fuse
and shadow register read sequence. We explicitly specify the
ipg clock for OCOTP as a result.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for clock gating of I2C2 and I2C3.
We use I2C2 in a (not yet mainlined) device tree.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enabled DAP (debug access port) by default. This enables the hw-
breakpoint framework to make use of the breakpoints and watchpoints
supported by hardware.
[ 0.215805] hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.224624] hw-breakpoint: maximum watchpoint size is 4 bytes.
Without this clock, the hw-breakpoint driver claims an undefined
instruction during initialization:
[ 0.227380] hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0
[ 0.227519] hw-breakpoint: CPU 0 failed to disable vector catch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After the cleanup on clock drivers, they are now ready to be moved into
drivers/clk. Let's move them into drivers/clk/imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
