The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd screen,
microsd slot, headphones, mini hdmi, mini usb b and power barrel connectors.
It uses a rtl8188cus usb wifi chip and a RDA 5875Y bluetooth chip attached
to uart2. It has a bma250 accelerometer attached to i2c1 addr 0x18, this
only works when ldo3 is set to 2.8 volt, otherwise i2c1 gets stuck, so
for now we mark i2c1 as failed.
It has a pixcir,pixcir_tangoc compatible touchscreen attached to i2c2 addr
0x5c. This is not enabled in this dts, because this variant of the
pixcir_tangoc has separate wakeup and enable pins both of which need
to be driven low before the touchscreen will work. Before we can enable
this the pixcir driver and devicetree-bindings need to be extended to
support these pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cubieboard uses the internal codec to output sound to its mini-jack.
Enable it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CHIP v0.2 has a composite output on a mini-jack connector, the audio
part being provided by the on-SoC codec. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Enable the audio-codec on the Mele A1000 top-set box.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The cubieboard2 uses the internal codec to output sound to its mini-jack.
Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
This commit enables the on-chip audio codec present on the A20 SoC
for the Cubietruck.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A20 SoC includes the Allwinner audio codec, capable of both 24-bit
playback and capture. This commit adds a device node for it.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A13 and A10s also have the audio codec present. List it in the device
tree.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A10 SoC includes the Allwinner audio codec, capable of both 24-bit
playback and capture. This commit adds a device node for it.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The audio codec functional clock is a child of PLL2 and is used to control
the audio rate, enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A20 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). Add it to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A13 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). However, it has a
different divider configuration than the A10, hence the difference
compatible.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A10 uses the PLL2 as the audio PLL, which is the parent of all the
other audio clocks in the system (i2s, codec, etc.). Add it to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The OTG arrangement on the LinkSprite pcDuino v3 Nano is the same as the
pcDuino 1/2/3: the OTG port's 5V line is connected directly to the 5V
bus (it's not switchable), and the OTG port's ID pin is connected to PH4
on the A20.
Tested successfully in both host and device modes.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a pinmux setting for using mmc2 in regular 4 bit mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When the gpio interrupt bindings where changed to add a bank to the
specifier list, the r_pio nodes of A23/A31/A33 where not updated to
match and neither was the pio node of the A80, this fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The NMI interrupt controller is in charge of the NMI pin exposed by
the SoC to the PMIC. The PMIC signals interrupts through this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DC5LDO regulator supplies VDD-CPUS, which is for the embedded
controller in the A31 SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have axp22x.dtsi describing common axp22x hardware, use
it and reference the nodes instead of declaring the whole tree.
Also drop the "always-on" from the vdd-gpu regulator, since we don't
support the GPU anyway.
And add a regulator reference for cpu0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The power configuration on this board is the same as the pcDuino v3.
This will enable frequency/voltage scaling over the standard A20
operating points from 144 MHz to 960 MHz.
Tested using cpufreq-ljt-stress-test on two pcDuino v3 Nano boards; also
tested successfully with voltages reduced by 0.025 V.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We've everything we need to support the gmac on Colombus, turn it on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A33 Q8 tablets with the et-q8-v1.6 pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the et-q8-v1.6.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A23 Q8 tablets with the ippo-q8h-v* pcb will work fine with the
generic q8-tablet.dts and given the many variants of PCBs found in
Q8 tablets using such a specific dts name was a mistake in hindsight.
We cannot just drop the ippo-q8h-v*.dtb as existing u-boot configs
may very well point to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a generic dts file for A23 based q8 formfactor tablets,
this is intended to replace both sun8i-a23-ippo-q8h-v5.dts and
sun8i-a23-ippo-q8h-v1.2.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
All A13 based q8 formfactor tablets use the same backlight setup, add
a backlight devicetree node for controlling the backlight on these devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Q8 format tablets use channel 0 of the PWM controller for backlight dimming.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a pinmux setting for the first pwm channel. This is often used for
backlight dimming on tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add dts nodes for the PWM controller on the A13 / A10s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The AXP22x family of PMIC is used with some Allwinner SoCs. This
includes the AXP221, AXP221s and AXP223. They differ in the host
interface, maximum supply current for DCDC1 regulator, and default
voltage and state for various LDO regulators. Also, the AXP221s
does not support fine calibration of the battery fuel gauge.
This patch adds a dtsi file for all the common bindings for these
PMICs. Currently this is just listing all the regulator nodes. The
regulators are initialized based on their device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The LinkSprite pcDuino v3 Nano's two USB host ports are powered by a
single RT9701GB regulator, which has its enable input tied to the A20's
PD2 pin, pulled up to 3v3 via a 10k resistor.
However, the script.bin that shipped with the device listed PH11 and PH3
as Vbus control pins for the two USB ports. Neither of these are
actually connected to anything.
Siarhei Siamashka spotted this problem while reviewing the other
LinkSprite boards. This patch fixes it by only defining a single
regulator, controlled by PD2. Testing shows that the USB ports are now
(correctly) only powered up once the USB PHY driver is loaded.
Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a separate pinctrl node for the UART3 CTS and RTS pins shared between
the A10s and A13.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The uart3 pins are shared between the A10s and A13, move the pinctrl node
to the common DTSI to avoid duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
The R8 is very close to the A13, but it still has a few differences,
notably a composite output, which the A13 lacks.
Add a DTSI based on the A13's to hold those differences.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Enable the otg/drc usb controller on the pcDuino1/2 board. Note
that the pcDuino1 FEX file from the vendor contains the following
information in the [usbc0] section:
usb_id_gpio = port:PH04<0><1><default><default>
usb_det_vbus_gpio = port:PH05<0><0><default><default>
usb_drv_vbus_gpio = port:PB09<1><0><default><0>
While the pcDuino2 FEX has:
usb_id_gpio = port:PH04<0><1><default><default>
usb_det_vbus_gpio = port:PH05<0><0><default><default>
usb_drv_vbus_gpio = port:PD02<1><0><default><0>
The ID pin is indeed PH4. The PD2 pin can be used to switch power
on/off for the USB Type A receptacle on pcDuino2, but it has nothing
to do with the MicroUSB OTG receptacle. The VBUS pin of the MicroUSB
receptacle is always connected to 5V according to the schematics
(both pcDuino1 and pcDuino2) and confirmed by doing some tests on
pcDuino2. The PH5 pin is just one of the pins on the J8 expansion
header and has nothing to do with USB OTG. The PB9 pin is pulled
up and connected to the N_VBUSEN pin of AXP209 PMIC, while the
VBUS pin of AXP209 only has a capacitor between it and the
ground (this pin is not used for anything else).
To sum it up. Only the ID pin (PH4) has a real use. And 5V voltage
is always served to the MicroUSB OTG receptacle no matter what is
the state of the PB9/PD2 pins.
This patch has been tested on pcDuino2 to work fine in a host role
with a USB keyboard connected via an OTG cable. It also works fine
in a device role (cdc_ether) with a regular Micro-B cable connected
to a desktop PC.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The LinkSprite pcDuino2 board is almost identical to the older
LinkSprite pcDuino1 board according to the schematic pdf files.
So we just include the existing "sun4i-a10-pcduino.dts" file and
make the necessary adjustments.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pcDuino1 board does not use any power switches at all for its
two USB host ports and the VBUS pins are always connected to 5V.
The pcDuino2 board uses the RT9701GB power switch for its single
USB host port, but the USB_EN pin (PD2) is pulled up with a 10K
resistor. So that the USB power is still enabled by default,
resulting in the same behaviour as pcDuino1 if nobody touches
the PD2 pin. This minor difference is going to be handled in a
follow-up patch, introducing a separate dts file for pcDuino2.
The primary reason for this fix is that the current dts file
unnecessarily meddles with the PH3 and PH6 pins. But the PH6 pin
is available on the Arduino-compatible expansion header and may
have a better use for other purposes. This patch fixes the
problem and now the PH6 pin can be used with the GPIO sysfs
interface. Tested on a pcDuino2 board with a multimeter:
echo 230 > /sys/class/gpio/export
echo "out" > /sys/class/gpio/gpio230/direction
echo 0 > /sys/class/gpio/gpio230/value
echo 1 > /sys/class/gpio/gpio230/value
USB still works as expected too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg/drc usb controller on the Bananapi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun7i-a20-bananapi.dts doesn't contain regulator nodes for the AXP209 PMU
driver, so add them to allow for voltage-scaling with cpufreq-dt. Also
add board-specific OPP to use slightly higher voltages at lower
frequencies since Kevin Hilman reported that not all BananaPi boards run
stable at the default voltages inherited by sun7i-a20.dtsi.
Signed-off-by: Timo Sigurdsson <public_timo.s@silentcreek.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
"dcdc1-supply" and "dcdc5-supply" have been dropped, as they are
internally connected and should not be represented in the device
tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Reduced Serial Bus controller is used to talk to the onboard PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Reduced Serial Bus controller is used to talk to the onboard PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds a device node for the Reduced Serial Bus (RSB)
controller and the defacto pinmux setting to the A23/A33 dtsi.
Since there is only one possible pinmux setting for RSB, just
set it in the dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This allows voltage-scaling with cpufreq-dt. The reliability of
voltage-scaling has been checked by reducing the voltage of all
operating points by 0.025V (for extra safety headroom) and running
libjpeg-turbo decoding tests on 5 pcDuino2 boards. It means that
the standard sun4i voltages should be perfectly fine too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A20-SOM-EVB is a reference design of a 2-layer board for the
A20-SOM.
It expands the features of A20-SOM by adding VGA connector, HDMI
connector, audio In/Out, LCD connector, 2 Mpix camera, gigabit
Ethernet, SATA, USB-OTG and 2 USB hosts.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
