Technically the display-hub driver could access registers via the
specified region, though it practice it will do so via the display
controllers' register regions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Technically the display-hub driver could access registers via the
specified region, though it practice it will do so via the display
controllers' register regions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The CEC controller found on Tegra194 can be used to control consumer
devices using the HDMI CEC pin.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The HDA controller found on Tegra194 can be used for audio playback over
HDMI.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The CEC controller found on Tegra186 can be used to control consumer
devices using the HDMI CEC pin.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The P2888 processor module contains a TI TMP451 temperature sensor with
two channels. These are used to measure the temperatures at different
locations on the module.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The power and force recovery buttons found on Jetson Xavier are hooked
up to two Tegra GPIOs. The power button can also function as a wake-up
source.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AON GPIO controller is in an always-on power partition and typically
provides pins for functions that need to always work, such as the power
key for example.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The on-die RTC isn't hooked up to a backup battery, so it isn't useful
to track time across reboots, but as long as power remains enabled, it
keeps track of time accurately and can be used to wake the system from
sleep, for example.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The RTC on Tegra194 is very similar to the RTC on earlier generations.
One notable exception is that the source clock is now the 32 kHz clock
instead of a dedicated RTC clock and the RTC alarm is a wake event and
can be used to wake the system from sleep.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Wake events are a feature that allows the interrupt and GPIO controllers
to be powered off as part of system sleep. The PMC which is always on is
monitoring these wake events and can power up subsequent controllers as
necessary to process them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The on-die RTC isn't hooked up to a backup battery, so it isn't useful
to track time across reboots, but as long as power remains enabled, it
keeps track of time accurately and can be used to wake the system from
sleep, for example.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The RTC on Tegra186 is very similar to the RTC on earlier generations.
One notable exception is that the source clock is now the 32 kHz clock
instead of a dedicated RTC clock and the RTC alarm is a wake event and
can be used to wake the system from sleep.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Wake events are a feature that allows the interrupt and GPIO controllers
to be powered off as part of system sleep. The PMC which is always on is
monitoring these wake events and can power up subsequent controllers as
necessary to process them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order for the correct interrupt type to be configured, the event
action for the power key needs to be "asserted".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable these thermal zones to be able to monitor their temperatures and
control the fan to cool down the system if necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the 5V HDMI regulator and hook up the VDD_1V0 and VDD_1V8HS supplies
from the PMIC to the display block. Also enable the display hub which is
responsible for instantiating the display controllers. Finally, enable
the third SOR that drives the TMDS signals to the HDMI connector.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra194 has a version of VIC that is very similar to that on Tegra186.
Add the device tree node for it that is enabled by default.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra194 contains a display architecture very similar to that found on
the Tegra186. One notable exception is that DSI is no longer a supported
output. Instead there are four display controllers and four SORs (with a
DPAUX associated to each of them) that can drive HDMI or DP.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The official name for the P2972-0000 board is Jetson AGX Xavier
Development Kit. Set that as the model string in the device tree for
clarity.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Populate the power-domain properties for the xHCI device for Tegra210.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra194 contains a version of the I2C controller that is no longer
compatible with the version found in Tegra114.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Configure sdmmc4 parent clock to pllc4 and sdmmc1 to pllp_out0 by
setting the assigned-clocks device tree properties. pllc4 offer
better jitter performance and should be used with higher speed
modes like HS200 and HS400.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use assigned-clock properties to configure pllc4 as the parent clock
for sdmmc4 on Tegra210. pllc4 offers better jitter perfomance than
the default pllp and is required by HS200 and HS400 modes.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the calibration offset properties used for automatic pad drive
strength calibration.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the calibration offset properties used for automatic pad drive
strength calibration.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Allow sdmmc1 to set the signaling voltage to 1.8 V in order to support
faster signaling modes.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On p2180 sdmmc4 is powered from a fixed 1.8 V regulator.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set regulator-min-microvolt property of ldo2 to 1.8 V in
tegra210-p2180.dtsi. ldo2 is used by the sdmmc1 SDHCI controller and its
voltage needs to be adjusted down to 1.8 V to support faster signaling
modes. It appears that the comment about the SDHCI driver requesting
invalid voltages no longer applies.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add pad voltage configuration nodes for sdmmc pads with configurable
voltages on Tegra186.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add pad voltage configuration nodes for sdmmc pads with configurable
voltages on Tegra210.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add CPU and PSCI nodes to device tree. The Tegra194 SoC contains
eight NVIDIA Carmel CPUs.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra194 contains the same ethernet controller as the Tegra186.
Add the device tree node for it, and correspondingly the PHY node
on the board device tree.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now that we have a GPIO controller, enable the card detect GPIO for
the SD card slot.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the device tree node for the GPIO controller on Tegra194.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Need to configure PHY interrupt as active low for P3310 Tegra186
platform otherwise it results in spurious interrupts.
This issue wasn't seen before because the generic PHY driver without
interrupt support was used.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
