Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates SB800 prefetch routine
in AMD PLL quirk. And make it use the new chipset type to represent SB800
generation.
[1] http://marc.info/?l=linux-usb&m=138012321616452&w=2
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit "usb: pci-quirks: refactor AMD quirk to abstract AMD chipset types"
introduced a new AMD chipset type to filter AMD platforms with different
chipsets.
According to a recent thread [1], this patch updates USB subsystem hang
symptom quirk which is observed on AMD all SB600 and SB700 revision
0x3a/0x3b. And make it use the new chipset type to represent.
[1] http://marc.info/?l=linux-usb&m=138012321616452&w=2
Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_clk_get() is used so there is no reason to explicitly
call clk_put() in probe or remove functions.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for non-NULL overrides before dereferencing since platforms may
pass in NULL overrides.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of usb phy reinitialization:
e.g. insmod usb-module(usb works well) -> rmmod usb-module -> insmod usb-module
It found the PHY_CLK_VALID bit didn't work if it's not with the power-on reset.
So we just check PHY_CLK_VALID bit during the stage with POR, this can be met
by the tricky of checking FSL_SOC_USB_PRICTRL register.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For controller versions greater than 1.6, setting ULPI_PHY_CLK_SEL
bit when USB_EN bit is already set causes instability issues with
PHY_CLK_VLD bit. So USB_EN is set only for IP controller version
below 1.6 before setting ULPI_PHY_CLK_SEL bit
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the OHCI pxa27x/pxa3xx host controller driver from
ohci-hcd host code so that it can be built as a separate driver
module. This work is part of enabling multi-platform kernels on
ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the OHCI EP93XX host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the OHCI NXP host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Many place function name and struct name started with usb,
current scenario replaced usb with ohci for proper naming.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Samsung OHCI S3C24xx/S3C64xx host controller driver
from ohci-hcd host code so that it can be built as a separate
driver module.This work is part of enabling multi-platform.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the TI OHCI Atmel host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the ST OHCI SPEAr host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the TI OHCI OMAP3 host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the TI OHCI OMAP1/2 host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the Samsung OHCI EXYNOS host controller driver from ohci-hcd
host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate the W90X900(W90P910) on-chip host controller driver from
ehci-hcd host code so that it can be built as a separate driver module.
This work is part of enabling multi-platform kernels on ARM;
however, note that other changes are still needed before W90X900(W90P910)
can be booted with a multi-platform kernel
and an ehci driver that only works on one of them.
With the infrastructure added by Alan Stern in patch 3e0232039
"USB: EHCI: prepare to make ehci-hcd a library module", we can
avoid this problem by turning a bus glue into a separate
module, as we do here for the w90X900 bus glue.
This patch is rebased on greghk/usb-next 3.12 rc1.
Signed-off-by: Manjunath Goudar <manjunath.goudar@linaro.org>
Signed-off-by: Deepak Saxena <dsaxena@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following patch is required to resolve remote wake issues with
certain devices.
Issue description:
If the remote wake is issued from the device in a specific timing
condition while the system is entering sleep state then it may cause
system to auto wake on subsequent sleep cycle.
Root cause:
Host controller rebroadcasts the Resume signal > 100 µseconds after
receiving the original resume event from the device. For proper
function, some devices may require the rebroadcast of resume event
within the USB spec of 100µS.
Workaroud:
1. Filter the AMD platforms with Yangtze chipset, then judge of all the usb
devices are mouse or not. And get out the port id which attached a mouse
with Pixart controller.
2. Then reset the port which attached issue device during system resume
from S3.
[Q] Why the special devices are only mice? Would high speed devices
such as 3G modem or USB Bluetooth adapter trigger this issue?
- Current this sensitivity is only confined to devices that use Pixart
controllers. This controller is designed for use with LS mouse
devices only. We have not observed any other devices failing. There
may be a small risk for other devices also but this patch (reset
device in resume phase) will cover the cases if required.
[Q] Shouldn’t the resume signal be sent within 100 us for every
device?
- The Host controller may not send the resume signal within 100us,
this our host controller specification change. This is why we
require the patch to prevent side effects on certain known devices.
[Q] Why would clicking mouse INTENSELY to wake the system up trigger
this issue?
- This behavior is specific to the devices that use Pixart controller.
It is timing dependent on when the resume event is triggered during
the sleep state.
[Q] Is it a host controller issue or mouse?
- It is the host controller behavior during resume that triggers the
device incorrect behavior on the next resume.
This patch sets USB_QUIRK_RESET_RESUME flag for these Pixart-based mice
when they attached to platforms with AMD Yangtze chipset.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch abstracts out a AMD chipset type which includes southbridge
generation and its revision. When os excutes usb_amd_find_chipset_info
routine to initialize AMD chipset type, driver will know which kind of
chipset is used.
This update has below benifits:
- Driver is able to confirm which southbridge generations and their
revision are used, with chipset detection once.
- To describe chipset generations with enumeration types brings better
readability.
- It's flexible to filter AMD platforms to implement new quirks in future.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Andiry Xu <andiry.xu@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, chipidea host has already depended on USB_EHCI_HCD
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for specifying soft dependencies in the modules themselves was
introduced in commit 7cb14ba.
In Arch we have always been shipping a module.d(5) fragment ordering ohci/uhci
after ehci. If this ordering is really necessary, it would be great to move it
to the kernel and getting the correct fragment generated by depmod.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since uhci-hcd, ehci-hcd, and xhci-hcd support runtime PM, the .pm
field in their pci_driver structures should be protected by CONFIG_PM
rather than CONFIG_PM_SLEEP. The corresponding change has already
been made for ohci-hcd.
Without this change, controllers won't do runtime suspend if system
suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in ohci-hcd. The change is more
complicated than it was in ehci-hcd, because ohci-hcd doesn't scan for
isochronous completions in the same way as ehci-hcd does. Rather, it
depends on the hardware adding completed TDs to a "done queue". Some
OHCI controller don't handle this properly when a TD's time slot has
already expired, so we have to avoid adding such TDs to the schedule
in the first place. As a result, if the URB was submitted too late
then none of its TDs will get put on the schedule, so none of them
will end up on the done queue, so the driver will never realize that
the URB should be completed.
To solve this problem, the patch adds one to urb_priv->td_cnt for such
URBs, making it larger than urb_priv->length (td_cnt already gets set
to the number of TD's that had to be skipped because their slots have
expired). Each time an URB is given back, the finish_urb() routine
looks to see if urb_priv->td_cnt for the next URB on the same endpoint
is marked in this way. If so, it gives back the next URB right away.
This should be applied to all kernels containing commit 815fa7b917
(USB: OHCI: fix logic for scheduling isochronous URBs).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
This patch implements the same policy in uhci-hcd. It should be
applied to all kernels containing commit c44b225077 (UHCI: implement
new semantics for URB_ISO_ASAP).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 24f531371d (USB: EHCI: accept very late isochronous URBs)
changed the isochronous API provided by ehci-hcd. URBs submitted too
late, so that the time slots for all their packets have already
expired, are no longer rejected outright. Instead the submission is
accepted, and the URB completes normally with a -EXDEV error for each
packet. This is what client drivers expect.
The same policy should be implemented in imx21-hcd, but I don't know
enough about the hardware to do it. As a second-best substitute, this
patch treats very late isochronous submissions as though the
URB_ISO_ASAP flag were set. I don't have any way to test this change,
unfortunately.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Sascha Hauer <kernel@pengutronix.de>
CC: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The halted state of a endpoint cannot be cleared over CLEAR_HALT from a
user process, because the stopped_td variable was overwritten in the
handle_stopped_endpoint() function. So the xhci_endpoint_reset() function will
refuse the reset and communication with device can not run over this endpoint.
https://bugzilla.kernel.org/show_bug.cgi?id=60699
Signed-off-by: Florian Wolter <wolly84@web.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When a device signals remote wakeup on a roothub, and the suspend change
bit is set, the host controller driver must not give control back to the
USB core until the port goes back into the active state.
EHCI accomplishes this by waiting in the get port status function until
the PORT_RESUME bit is cleared:
/* stop resume signaling */
temp &= ~(PORT_RWC_BITS | PORT_SUSPEND | PORT_RESUME);
ehci_writel(ehci, temp, status_reg);
clear_bit(wIndex, &ehci->resuming_ports);
retval = ehci_handshake(ehci, status_reg,
PORT_RESUME, 0, 2000 /* 2msec */);
Similarly, the xHCI host should wait until the port goes into U0, before
passing control up to the USB core. When the port transitions from the
RExit state to U0, the xHCI driver will get a port status change event.
We need to wait for that event before passing control up to the USB
core.
After the port transitions to the active state, the USB core should time
a recovery interval before it talks to the device. The length of that
recovery interval is TRSMRCY, 10 ms, mentioned in the USB 2.0 spec,
section 7.1.7.7. The previous xHCI code (which did not wait for the
port to go into U0) would cause the USB core to violate that recovery
interval.
This bug caused numerous USB device disconnects on remote wakeup under
ChromeOS and a Lynx Point LP xHCI host that takes up to 20 ms to move
from RExit to U0. ChromeOS is very aggressive about power savings, and
sets the autosuspend_delay to 100 ms, and disables USB persist.
I attempted to replicate this bug with Ubuntu 12.04, but could not. I
used Ubuntu 12.04 on the same platform, with the same BIOS that the bug
was triggered on ChromeOS with. I also changed the USB sysfs settings
as described above, but still could not reproduce the bug under Ubuntu.
It may be that ChromeOS userspace triggers this bug through additional
settings.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If a command on the command ring needs to be cancelled before it is handled
it can be turned to a no-op operation when the ring is stopped.
We want to store the command ring enqueue pointer in the command structure
when the command in enqueued for the cancellation case.
Some commands used to store the command ring dequeue pointers instead of enqueue
(these often worked because enqueue happends to equal dequeue quite often)
Other commands correctly used the enqueue pointer but did not check if it pointed
to a valid trb or a link trb, this caused for example stop endpoint command to timeout in
xhci_stop_device() in about 2% of suspend/resume cases.
This should also solve some weird behavior happening in command cancellation cases.
This patch is based on a patch submitted by Sarah Sharp to linux-usb, but
then forgotten:
http://marc.info/?l=linux-usb&m=136269803207465&w=2
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
When a command times out, the command ring is first aborted,
and then stopped. If the command ring is empty when it is stopped
the stop event will point to next command which is not yet set.
xHCI tries to handle this next event often causing an oops.
Don't handle command completion events on stopped cmd ring if ring is
empty.
This patch should be backported to kernels as old as 3.7, that contain
the commit b92cc66c04 "xHCI: add aborting
command ring function"
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Giovanni <giovanni.nervi@yahoo.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
This reverts commit 3b8d7321ed, which
brings back commit 428aac8a81 as it should
be working for the 3.13-rc1 merge window now that Alan's other fixes are
here in the tree already.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have USB fixes now in Linus's tree that we need to properly sort out
with reverts and the like in the usb-next branch, so merge them together
and do it by hand.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=51X+
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.12-rc2
Here's first set of fixes for v3.12-rc series, patches have
been soaking in linux-usb for a while now.
We have the usual sparse and build warnings, a Kconfig fix
to a mismerge on dwc3 Kconfig, fix for a possible memory leak
in dwc3, s3c-hsotg won't disconnect when bus goes idle, locking
fix in mv_u3d_core, endpoint disable fix in f_mass_storage.
We also have one device ID added to dwc3's PCI glue layer in order
to support Intel's BayTrail devices.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the iso_stream_schedule() routine in ehci-sched.c
to handle cases where an underrun causes an isochronous endpoint's
queue to empty out, but the client driver wants to maintain
synchronization with the device (i.e., the URB_ISO_ASAP flag is not
set). This could not happen until recently, when ehci-hcd switched
over to completing URBs in a tasklet.
(This may seem like an unlikely case to worry about, but underruns are
all too common with the snd-usb-audio driver, which doesn't use
URB_ISO_ASAP.)
As part of the fix, some URBs may need to be given back when they are
submitted. This is necessary when the URB's scheduled slots all fall
before the current value of ehci->last_iso_frame, and as an
optimization we do it also when the slots all fall before the current
frame number.
As a second part of the fix, we may need to skip some but not all of
an URB's packets. This is necessary when some of the URB's scheduled
slots fall before the current value of ehci->last_iso_frame and some
of them fall after the current frame number. A new field
(first_packet) is added to struct ehci_iso_sched, to indicate how many
packets should be skipped.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch interchanges the "if" and "else" branches of the big "if"
statement in iso_stream_schedule(), in preparation for the next patch
in this series. That is, it changes
if (likely(!...)) {
A
} else {
B
}
to
if (unlikely(...)) {
B
} else {
A
}
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 428aac8a81.
This isn't quite ready for 3.12, we need some more EHCI driver changes
that are just now showing up. So revert this for now, and queue it up
later for 3.13.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local symbols used in this file are made static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlJJ8ACgkQMUfUDdst+ymBAwCgg8czTAuwpCCK7H8LHnC2BsMj
dtUAnjDisrbw4qWSXaaA/sfgSZjKW5G4
=Tman
-----END PGP SIGNATURE-----
Merge tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB driver pull request for 3.12-rc1
Lots of USB driver fixes and updates. Nothing major, just the normal
xhci, gadget, and other driver changes. Full details in the shortlog"
* tag 'usb-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (352 commits)
usbcore: fix incorrect type in assignment in descriptors_changed()
usbcore: compare and release one bos descriptor in usb_reset_and_verify_device()
ehci: remove debugging statement with ehci statistics in ehci_stop()
ehci: remove duplicate debug_async_open() prototype in ehci-dbg.c
ehci: enable debugging code when CONFIG_DYNAMIC_DEBUG is set
ehci: remove ehci_vdbg() verbose debugging statements
Documentation sysfs-bus-usb: Document which files are used by libusb
Documentation sysfs-bus-usb: Document the speed file used by libusb
Documentation sysfs-bus-usb: Move files with known users to stable
USB: fix build error when CONFIG_PM_SLEEP isn't enabled
usb: r8a66597-hcd: use platform_{get,set}_drvdata()
usb: phy-tegra-usb: use platform_{get,set}_drvdata()
usb: acm gadget: Null termintate strings table
dma: cppi41: off by one in desc_to_chan()
xhci: Fix warning introduced by disabling runtime PM.
dev-core: fix build break when DEBUG is enabled
USB: OHCI: Allow runtime PM without system sleep
usb: ohci-at91: remove unnecessary dev_set_drvdata()
usb: renesas_usbhs: use platform_{get,set}_drvdata()
usb: fotg210-udc: use platform_{get,set}_drvdata()
...
This patch removes the ehci statictics information output in ehci_stop()
because they do not provide interesting info. At any case, the current
statistics can be viewed by reading the 'registers' file in debugfs.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the duplicate of debug_async_open() prototype following
three lines below the debug_async_open() declaration.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debugging code for ehci is enabled to run if the DEBUG flag is defined.
This patch enables the debugging code also when the kernel is configured
with dynamic debugging on.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes ehci_vdbg debugging statements from EHCI host controller
driver because they produce too much information, lowering the signal to noise
ratio when debugging, and because they are not used anymore.
Signed-off-by: Xenia Ragiadakou <burzalodowa@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
This first patch should fix the build breakage Sedat Dilek reported.
Apologizes for not including this patch before commit
0730d52a86 "xhci:prevent "callbacks suppressed"
when debug is not enabled"
The second patch fixes a new build warning introduced by commit
c8476fb855 "usb: xhci: Disable runtime PM suspend
for quirky controllers", which was caught by the 0day build system.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=siJK
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-08-27-15-07' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Fix build breakage and new warnings.
Hi Greg,
This first patch should fix the build breakage Sedat Dilek reported.
Apologizes for not including this patch before commit
0730d52a86 "xhci:prevent "callbacks suppressed"
when debug is not enabled"
The second patch fixes a new build warning introduced by commit
c8476fb855 "usb: xhci: Disable runtime PM suspend
for quirky controllers", which was caught by the 0day build system.
Sarah Sharp
Since ohci-hcd supports runtime PM, the .pm field in its pci_driver
structure should be protected by CONFIG_PM rather than
CONFIG_PM_SLEEP.
Without this change, OHCI controllers won't do runtime suspend if
system suspend or hibernation isn't enabled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
