We are not checking the return value from a call to wm_adsp_buffer_init
it looks like this used to be returned at the bottom of the function but
probably got missed when more error paths were added. This patch adds
the appropriate error check.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The internal codec on A23/A33/H3 is split into 2 parts. The
analog path controls are routed through an embedded custom register
bus accessed through the PRCM block.
The SoCs share a common set of inputs, outputs, and audio paths.
The following table lists the differences.
----------------------------------------
| Feature \ SoC | A23 | A33 | H3 |
----------------------------------------
| Headphone | v | v | |
----------------------------------------
| Line Out | | | v |
----------------------------------------
| Phone In/Out | v | v | |
----------------------------------------
Add an ASoC component driver for it. This should be tied to the codec
audio card as an auxiliary device. This patch adds the commont paths
and controls, and variant specific headphone out and line out.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
IOMMU needs DMA mapping function to use it. One solution is that
we can use DMA mapped dev on snd_pcm_lib_preallocate_pages_for_all()
for SNDRV_DMA_TYPE_DEV. But pcm_new and dma map timing are mismatched.
Thus, this patch uses SNDRV_DMA_TYPE_CONTINUOUS for pcm_new,
and use dma_sync_single_for_xxx() for each transfer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current Renesas Sound driver requests DMA channel when .probe timing,
and release it when .remove timing. And use DMA on .start/.stop
But, Audio DMAC power ON was handled when request timing (= .probe),
and power OFF was when release timing (= .remove).
This means Audio DMAC power is always ON during driver was enabled.
The best choice to solve this issue is that DMAEngine side handle
this. But current DMAEngine API design can't solve atmic/non-atmic
context issue for power ON/OFF. So next better choice is sound
driver request/release DMA channel each time. This patch do it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The kcontrol pointer in wm_coeff_ctl is not used now.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were adding firmware controls as card controls (using
snd_soc_add_codec_controls). The DSP is part of a specific codec so
we should be adding them as codec controls. Adding as codec controls
also means that if the codec has a name_prefix it will be added to
the control name, which won't happen when adding as a card control.
As that was the only use of the card pointer in struct wm_adsp it can
be removed.
For ADSP2 codecs a wm_adsp2_codec_probe() was added since the original
control handling was written, and that's the logical place to store a
pointer to the codec rather than delaying it until the codec is
powered-up.
For ADSP1 we don't use a codec_probe() stage so the codec pointer
initialization replaces the original card pointer initialization in
wm_adsp1_event().
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
cht_bsw_rt5645 driver allocates the own codec_id string but doesn't
release it. For simplicity, put the string in cht_mc_private; then
the string is allocated in a shot and released altogether.
Fixes: c8560b7c91 ("ASoC: cht_bsw_rt5645: Fix writing to string literal")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S sound drivers for SmartQ board and WM8580 codec can be compile
tested to increase build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of build time, Samsung ASoC drivers have rather runtime
dependency on Exynos or other Samsung platforms. For building they
require Common Clock Framework. If it is provided they could be compile
tested to increase build coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
MACH_SMDKC100, MACH_SMDKV210 and MACH_SMDKC110 are no longer supported
so we can drop the dead code. After this the driver no longer
differentiates between machines (S3C24xx machines are not supported by
it) so there is no need to override I2S device id in cpu_dai_name and
SEC_PLAYBACK dai_link can be removed as well.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
MACH_SMDKC100 was removed in commit b8529ec1c1 ("ARM: S5PC100: no more
support S5PC100 SoC"). MACH_SMDKV210 and MACH_SMDKC110 in commit
28c8331d38 ("ARM: S5PV210: Remove support for board files").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
dpcm_state_string() returns a pointer to a string literal. Modifying a
string literal causes undefined behaviour. So make the return type of the
function const char * to make it explicit that the returned value should
not be modified.
This patch is purely cosmetic, none of the users of dpcm_state_string()
attempt to modify the returned content.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8580 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm8523 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control list may contain shutdown controls for firmwares that are
not currently active, attempting to write this will at best fail. To
avoid this issue we skip any control that is not active.
Fixes: commit f4f0c4c60c ("ASoC: wm_adsp: Signal firmware shutdown
through event control")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Three trivial fixes: a regression fix for ASRock mobo, a
use-after-free fix at hot-unplug of USB-audio, and a quirk for new
Thinkpad models.
-----BEGIN PGP SIGNATURE-----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=aKgB
-----END PGP SIGNATURE-----
Merge tag 'sound-4.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Three trivial fixes:
A regression fix for ASRock mobo, a use-after-free fix at hot-unplug
of USB-audio, and a quirk for new Thinkpad models"
* tag 'sound-4.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Fix use-after-free of usb_device at disconnect
ALSA: hda - Fix mic regression by ASRock mobo fixup
ALSA: hda - add a new condition to check if it is thinkpad
wm9081 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C)
And, this patch adds "depends on I2C" to Kconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
uda1380 driver doesn't work without CONFIG_I2C anyway.
Let's remove #if IS_ENABLED(CONFIG_I2C), and use module_i2c_driver().
And, this patch adds "depends on I2C" to Kconfig
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TSE-850 is an FM Transmitter Station Equipment, designed to generate
baseband signals for FM, mainly the DARC subcarrier, but other signals
are also possible.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
When this driver masters BCLK and/or LRCLK, and noone has stated
differently, assume that all the bits of a frame are used.
This relieves the cpu dai users from the duty to fill in the dividers for
the common case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
const char * const [] is the preferred type for static string arrays since
this states explicitly that the individual entries are not going to be
changed. Due to limitations in the ASoC API it was not possible to use it
for enum text arrays. Commit 87023ff74b ("ASoC: Declare const properly
for enum texts") changed this, but most drivers still use 'const char
* []' as the type for their enum text arrays.
Change these occurrences of 'static * const char * []' to 'static const
char * const []'.
The conversion was done automatically using the following coccinelle
semantic patch:
// <smpl>
@disable optional_qualifier@
identifier s;
@@
static
-const char *
+const char * const
s[] = ...;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch is a cleanup of EMU1010 dock probing code in emu10k1 driver
to use work instead of kthread in a loop. The work is lighter and
easier to control than kthread, in general.
Instead of a loop with the explicit sleep, we do simply
delayed-schedule the work. At suspend/resume callbacks, the work is
canceled and restarted, respectively.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The EMU1010 support in emu10k1 driver has two request_firmware()
calls, one for the main board and one for the dock. Both call
patterns are fairly similar, and we can simplify it by introducing a
helper function and a table instead of the open switch/case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The emu1010_firmware_thread() checks the previous dock status, but a
wrong register is recorded as the last status when the dock is plugged
in. Usually this isn't a big issue since this value gets overwritten
by the next loop after one second. But when a dock is unplugged
immediately after plugging, it means essentially missing undock
handling.
This patch addresses it by remembering the correct register value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sphinx takes a word like (*foo)->bar in the kernel-doc comments as a
part of the emphasized marker, and complains like
./sound/pci/ac97/ac97_codec.c:1908: WARNING: Inline emphasis start-string without end-string.
For avoiding this, wrap it with the quotes (``) in the comment.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The usb-audio driver implements the deferred device disconnection for
the device in use. In this mode, the disconnection callback returns
immediately while the actual ALSA card object removal happens later
when all files get closed. As Shuah reported, this code flow,
however, leads to a use-after-free, detected by KASAN:
BUG: KASAN: use-after-free in snd_usb_audio_free+0x134/0x160 [snd_usb_audio] at addr ffff8801c863ce10
Write of size 8 by task pulseaudio/2244
Call Trace:
[<ffffffff81b31473>] dump_stack+0x67/0x94
[<ffffffff81564ef1>] kasan_object_err+0x21/0x70
[<ffffffff8156518a>] kasan_report_error+0x1fa/0x4e0
[<ffffffff81564ad7>] ? kasan_slab_free+0x87/0xb0
[<ffffffff81565733>] __asan_report_store8_noabort+0x43/0x50
[<ffffffffa0fc0f54>] ? snd_usb_audio_free+0x134/0x160 [snd_usb_audio]
[<ffffffffa0fc0f54>] snd_usb_audio_free+0x134/0x160 [snd_usb_audio]
[<ffffffffa0fc0fb1>] snd_usb_audio_dev_free+0x31/0x40 [snd_usb_audio]
[<ffffffff8243c78a>] __snd_device_free+0x12a/0x210
[<ffffffff8243d1f5>] snd_device_free_all+0x85/0xd0
[<ffffffff8242cae4>] release_card_device+0x34/0x130
[<ffffffff81ef1846>] device_release+0x76/0x1e0
[<ffffffff81b37ad7>] kobject_release+0x107/0x370
.....
Object at ffff8801c863cc80, in cache kmalloc-2048 size: 2048
Allocated:
[<ffffffff810804eb>] save_stack_trace+0x2b/0x50
[<ffffffff81564296>] save_stack+0x46/0xd0
[<ffffffff8156450d>] kasan_kmalloc+0xad/0xe0
[<ffffffff81560d1a>] kmem_cache_alloc_trace+0xfa/0x240
[<ffffffff8214ea47>] usb_alloc_dev+0x57/0xc90
[<ffffffff8216349d>] hub_event+0xf1d/0x35f0
....
Freed:
[<ffffffff810804eb>] save_stack_trace+0x2b/0x50
[<ffffffff81564296>] save_stack+0x46/0xd0
[<ffffffff81564ac1>] kasan_slab_free+0x71/0xb0
[<ffffffff81560929>] kfree+0xd9/0x280
[<ffffffff8214de6e>] usb_release_dev+0xde/0x110
[<ffffffff81ef1846>] device_release+0x76/0x1e0
....
It's the code trying to clear drvdata of the assigned usb_device where
the usb_device itself was already released in usb_release_dev() after
the disconnect callback.
This patch fixes it by checking whether the code path is via the
disconnect callback, i.e. chip->shutdown flag is set.
Fixes: 79289e2419 ('ALSA: usb-audio: Refer to chip->usb_id for quirks...')
Reported-and-tested-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In commit 022d00ee0b ("ASoC: lpass-platform: Fix broken pcm data
usage") the stream specific information initialization was broken, with
the dma channel information not being initialized if there was no
alloc_dma_channel() helper function.
Before that, the DMA channel number was implicitly initialized to zero
because the backing store was allocated with devm_kzalloc(). When the
init code was rewritten, that implicit initialization was lost, and gcc
rightfully complains about an uninitialized variable being used.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lookup of the base register corresponding to a control is
duplicated in read and write so factor it out into a separate
function.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rtd->codec does not necessarily point to the CODEC instance for which the
callback was called (e.g. for CODEC<->CODEC or multi-CODEC links). Use
dai->codec instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
const char * const [] is the preferred type for static string arrays since
this states explicitly that the individual entries are not going to be
changed. Due to limitations in the ASoC API it was not possible to use it
for enum text arrays. Commit 87023ff74 ('ASoC: Declare const properly for
enum texts') changed this, but most drivers still use 'const char
* []' as the type for their enum text arrays.
Change these occurrences of 'static * const char * []' to 'static const
char * const []'.
The conversion was done automatically using the following coccinelle semantic
patch:
// <smpl>
@disable optional_qualifier@
identifier s;
@@
static
-const char *
+const char * const
s[] = ...;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a missing whitespace in the dev_err message between
"will" and "lead". Add the whitespace.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC Compress ops have only platform ops and no DAI ops unlike PCM device
where we have both platform ops as well as DAI ops.
So add compress dai ops and add this new structure to the ASoC core to make
compressed devices a first class ASoC citizen
Again like PCM ops, drivers are free to implement either or both of
these ops based on device needs.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most Baytrail-CR devices use analog differential microphones,
modify capture default to avoid DMI quirks. Keep digital mics
for all other configurations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Baytrail-CR devices usually expose information in the DSDT
which can be used to auto-detect AIF1/AIF2 connections.
The CHAN package contains two integers, the first one describes
the AIF number (1: AIF1, 2: AIF2) and the second the MCLK
value (ignored in this patch)
For example the following information is found in Lenovo 100s:
Device (RTEK) {
[...]
Name (CHAN, Package (0x02)
{
One,
0x017D7840
})
While on Asus T100TAF the package values are:
Name (CHAN, Package (0x02)
{
0x02,
0x017D7840
})
This patch relies on the new common routine to extract
a package exposed by a device indexed with the HID value.
The CHAN package contents are queried from the machine driver
and stored in a structure.
If this auto-detection fails (missing or bad package in the
BIOS), the routing falls back to SSP0-AIF2.
Note that quirks may still be needed to support mono speakers
or microphone, but this should reduce the number of issues with
Baytrail significantly.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new common routine to extract a package exposed by a
device indexed with the HID value. The functionality is
implemented without assumptions on the package type or
structure to allow for reuse. The caller is responsible for
defining the name and allocating structures to store the
results, ACPICA will complain in case of type mismatches
or buffer size issues.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAC3101 is mostly identical to DAC3100 with the exception that it has
stereo speaker AMP instead of mono used in DAC3100.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch handles publishing acknowledged controls through ALSA.
These controls allow user-side to send events to the firmware and
wait for the firmware to acknowledge it.
Note that although acked controls only operate in the direction
host->firmware, and therefore they are write-only as seen from user-
side code, we have to make them readable to account for all the code
out there that assumes that ALSA controls are always readable (amixer
for example.)
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for firmware controls marked SYSTEM. These are
internal to the driver-firmware interface and do not have
a user-accessible ALSA control.
Signed-off-by: Stuart Henderson <stuarth@opensource.wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch factors out converting a memory region type into
a name string, mainly so that it can be used in log commands.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the firmware has any system event signalling controls, signal
them during DSP PRE_PMD to tell the firmware it is about to be stopped.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SND_SOC_SMDK_WM8580_PCM Kconfig entry depends on either MACH_SMDKV210
or MACH_SMDKC110. Both of which were removed in commit 28c8331d38 ("ARM:
S5PV210: Remove support for board files") over two years ago. The driver
has been unselectable ever since.
Considering the lack of complaints about this it can be concluded that the
driver is unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a076d41823 ("ASoC: samsung: Drop AC97 drivers") removed some
unused code and the associated Kconfig options, but left those options
referenced in the Makefile. Remove the leftover references in the
Makefile.
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver fine-tune some parameters to improve FLL performance.
Those items have description as follow.
(1)ICTRL_LATCH: FLL DSP speed capability control
When FLL running at high frequency with long decimal number, DSP needs
to operate at high speed. FLL DSP can optimize between performance and
power consumption by ICTRL_LATCH.(111 has highest power consumption.)
The default setting can be used to reduce power.
(2)CUTOFF500: loop filter cutoff frequency at 500Khz
It will give the best FLL performance but highest power consumption
to enable the cutoff frequency. FLL Loop Filter enable to reduce FLL
output noise, especially,(DCO frequency)/(FLL input reference frequency)
is not a integer.
(3)GAIN_ERR: FLL gain error correction threshold setting
The threshold is comparison between DCO and target frequency.
The value 1111 has the most sensitive threshold, that is, 1111 can have
the most accurate DCO to target frequency. However, the gain error setting
conditionally and inversely depends on FLL input reference clock rate.
Higher FLL reference input frequency can only set lower gain error, such
as 0000 for input reference from MCLK=12.288Mhz. On the other side, if FLL
reference input is from Frame Sync, 48KHz, higher error gain can apply
such as 1111.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Over Sampling Rate (OSR) is defined as CLK_ADC frequency divided by the
audio sample rate (Fs).
OSR = CLK_ADC / FS
The available OSRs are 32, 64, 128 or 256. Note that the OSR and Fs
values must be selected such that the maximum frequency of CLK_ADC
is less than 6.144 MHz. It is recommended to match the relationship
between OSR and clock SRC according to following Table.
ADC_RATE: 00(OSR=32) | CLK_ADC_SRC: 11(CODEC 1/8)
ADC_RATE: 01(OSR=64) | CLK_ADC_SRC: 10(CODEC1/4)
ADC_RATE: 10(OSR=128) | CLK_ADC_SRC: 01(CODEC 1/2)
ADC_RATE: 11(OSR=256) | CLK_ADC_SRC: 00(CODEC CLK)
The over sampling rate about DAC follows the same rule with ADCs.
The driver changes the OSR to 64 value when initiation for better FLL
performance and applies the dynamic SRC change by different OSR.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the short Frame Sync detection logic enabled, the logic will check the
short frame sync threshold. If frame sync is less than the setting;
for example, frame sync less than 252 MCLK, the short frame sync signal is
flagged, digital filter temporary mute and skip that data.
If the system was intended for sampling rate change which could create
temporary short frame sync and not enough MIPS to run the digital filter.
But the situation doesn't happen in ALSA architecure. Thus the Frame Sync
is always stable, then no require to do the detection. Therefore,
the dirver disables the function for better performance.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_get_dai_name() is used from snd_soc_of_get_dai_name(),
and it is assuming that DT is using "sound-dai" / "#sound-dai-cells".
But graph base DT is using "remote-endpoint". This patch makes
snd_soc_get_dai_name() non static for graph support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is assuming that the card related information is located on
"card" node, but graph case doesn't have it.
This patch adds node parameter to adjust for graph support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit [1a3f099101: ALSA: hda - Fix surround output pins for
ASRock B150M mobo] introduced a fixup of pin configs for ASRock
mobos to fix the surround outputs. However, this overrides the pin
configs of the mic pins as if they are outputs-only, effectively
disabling the mic inputs. Of course, it's a regression wrt mic
functionality.
Actually the pins 0x18 and 0x1a don't need to be changed; we just need
to disable the bogus pins 0x14 and 0x15. Then the auto-parser will
pick up mic pins as switchable and assign the surround outputs there.
This patch removes the incorrect pin overrides of NID 0x18 and 0x1a
from the ASRock fixup.
Fixes: 1a3f099101 ('ALSA: hda - Fix surround output pins for ASRock...')
Reported-and-tested-by: Vitor Antunes <vitor.hda@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=187431
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The compatible table was not updated when the support for DAC3100 was added.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to arizona_init_notifiers was only added for CODECs that are
generating voice trigger events, however, this is somewhat annoying
for machine drivers that might be used with multiple CODECs as they
need to conditionally register for the notifier, depending on the
CODEC being attached.
As the cost of initialising the notifier is so minimal, and we may
well add other events in the future that apply to more CODECs, simply
do this for all Arizona CODECs.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These functions are very thin wrappers around core functions, so they
make sense as inline functions. Also making them inline avoids build
issues in the case where the machine driver is built in but the CODEC
is built as a module.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The core expects "const char * const" and "unsigned int" for enum
controls, the mixer control definitions in wm2200 use "const char *"
and "int". This patch corrects the type of these arrays.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/cs42l42.c:1972:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Latest Thinkpad laptops use the HKEY_HID LEN0268 instead of the
LEN0068, as a result neither audio mute led nor mic mute led can work
any more.
After adding the new HKEY_HID into the is_thinkpad(), both of them
works well as before.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While going to suspend, if we have any pending D0i3 work scheduled,
flush that and force the DSP to goto D0i3 mode before going to suspend.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We were invoking pci_disable_device() while going to suspend-to-idle and
pci_enable_device() while coming back to active state.
Turns out that we do not need these calls as we only need system to be
wake capable when in suspend-to-idle state. The wake capability is
already done by enable_irq_wake() calls, so remove these unwanted calls
in driver.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if the name strings are properly terminated, and only use valid
name strings to find existing physical DAI links to configure.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pm8916_wcd_analog_enable_micbias_int1() should set micbias1_cap_mode
rather than micbias2_cap_mode.
Also change the order of pm8916_wcd_analog_enable_micbias_int1/init2
functions for better readability.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix build errors in sound/soc/fsl/fsl_spdif.c by selecting BITREVERSE.
Fixes these build errors:
sound/built-in.o: In function `spdif_write_channel_status':
fsl_spdif.c:(.text+0xbe39d): undefined reference to `byte_rev_table'
fsl_spdif.c:(.text+0xbe3a8): undefined reference to `byte_rev_table'
fsl_spdif.c:(.text+0xbe3be): undefined reference to `byte_rev_table'
fsl_spdif.c:(.text+0xbe3d8): undefined reference to `byte_rev_table'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The later Allwinner SoCs have a dedicated reset controller, and
peripherals have dedicated reset controls which need to be deasserted
before the associated peripheral can be used.
Add support for this to the quirks structure and probe/remove functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31's internal codec capture path has a mixer in front of the ADC
for each channel, capable of selecting various inputs, including
microphones, line in, phone in, and the main output mixer.
This patch adds the various controls, widgets and routes needed for
audio capture from the already supported inputs on the A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support was added to allow location of both CPU and CODEC components
of a DAI link from their parent's of_node if they did not have an
of_node themselves in this commit:
commit 3e0aa8d83b ("ASoC: core: If component doesn't have of_node
use parent's node instead")
However this leaves platforms as something of a special case as the
major DAI component that doesn't do this. Since this is useful for MFD
devices which often utilise a single device tree entry for the whole
device, add support for looking up platforms from the parent's of_node
as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using simple-card with the wm8978 doesn't work because simple card calls
set_sysclk on the clock index 0, which is not the MCLK in the WM8978.
Adjust the clock definition so that the clock 0 is the MCLK.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In our i2s driver, we were previously trying to guess which oversample the
user wanted to use by looking at the rate and trying to max it.
However, the cards, and especially simple-card with its mclk-fs property
will already provide the expected oversample ratio by using the set_sysclk
callback.
We can thus implement it and remove the logic to deal with the runtime
guess.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for Cirrus Logic CS42L42 codec. SoundWire support
is not enabled. Features support for I2C control and I2S audio.
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A bugfix accidentally removed the implicit initialization of the
dma channel number, causing undefined behavior when
v->alloc_dma_channel is NULL:
sound/soc/qcom/lpass-platform.c: In function ‘lpass_platform_pcmops_open’:
sound/soc/qcom/lpass-platform.c:83:29: error: ‘dma_ch’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds back an explicit initialization to zero, restoring the
previous behavior for that case.
Fixes: 022d00ee0b ("ASoC: lpass-platform: Fix broken pcm data usage")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the ALSA proc handler allows read or write even if the proc
file were write-only or read-only. It's mostly harmless, does thing
but allocating memory and ignores the input/output. But it doesn't
tell user about the invalid use, and it's confusing and inconsistent
in comparison with other proc files.
This patch adds some sanity checks and let the proc handler returning
an -EIO error when the invalid read/write is performed.
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ALSA proc handler allows currently the write in the unlimited size
until kmalloc() fails. But basically the write is supposed to be only
for small inputs, mostly for one line inputs, and we don't have to
handle too large sizes at all. Since the kmalloc error results in the
kernel warning, it's better to limit the size beforehand.
This patch adds the limit of 16kB, which must be large enough for the
currently existing code.
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYHmoCAAoJEHm+PkMAQRiG7RMIAI2i7Y5hpL5yCxK5AFaL4u/G
KxXfp1B1UanUTgjOmd7zGqtDYcFX9t7GTTUFixQ7/9Opr4PD9qbnatoDGSc3xjbT
msDgA1B78F1/Q3kHWfeGq32MihQ4mj5NwUCo+igUcUvvWG7mHgzErj/Nh5RoobQX
p/izdpTbrw3GX6xXB8olbG7XWHaVye/+TT3q6+gmgm8I/QEujcLeGoycE0zlhPN8
FG/JX76At/+ZM2Py7Oxo3k+oKL9CHrtOQYDp/wN0uslV5eYvvkZz0/M1HMOGZt+c
gZU5jzM17K7C4Nzo06WAuBU9wUBGc25m+cPicLlOmljnzfU+f50SKaDjZq3p7QI=
=2KUF
-----END PGP SIGNATURE-----
Backmerge tag 'v4.9-rc4' into drm-next
Linux 4.9-rc4
This is needed for nouveau development.
The A31 SoC's codec has various inputs, outputs and microphone bias
supplies. These can be routed on the board in different ways, such as:
- HPCOM may be connected to have the headphone DC coupled.
- Microphones all use the MBIAS main microphone supply or one mic may
use the HBIAS supply, which supports headset detection and buttons.
- Line Out may be routed to an audio jack, or an onboard speaker amp
with power controls.
Add support for specifying the audio routes in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 internal codec has 3 microphone outputs, of which MIC2 and MIC3
are muxed internally. The resulting two microphone inputs have separate
gain controls and mixer inputs.
The codec also has 2 microphone bias pins. HBIAS is specifically for the
headphone jack, which also supports headphone detection and control
buttons. These extra functions are not supported yet. The other, MBIAS,
is for all other analog microphones.
There is also mention of digital microphone support, but documentation
is scarce, and no hardware with it is available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 integrated codec has a second "Line Out" output which does not
include an integrated amplifier in its path. This path does have a
separate volume control.
This patch adds support for the playback path from the DAC to the Line
Out pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the regmap conversion ac97_read/ac97_write are just simple wrappers
around snd_soc_read/snd_soc_write. Use those instead directly and remove
the wrappers.
Also use snd_soc_update_bits() where appropriate.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the stac9766 driver still uses custom snd_soc_codec_driver IO
callbacks. This has been deprecated for a while, so convert the stac9766
driver to use regmap for its IO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The stac9766 driver has a header file that defines 3 register locations.
Move these to the main source file since it is not really worth it having a
separate file for them. The header file is now empty and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AC'97 standard defines paging support for the register range 0x60-0x6f.
Meaning registers in this window are mapped to different physical registers
depending on the setting of the page select register (0x24).
The stac9766 implements support for switching between page 0 and page 1
depending on the addressed register. But the driver never accesses any
registers from page 1, in addition page 0 is the page selected by default.
Considering the development history it is unlikely that the driver will see
any new features that require paging support. Removing the paging support
makes transitioning the driver to regmap a bit more straight forward.
The default register value table is update to contain the values from page
0, rather than page 1.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI ID defines are back from the time when DAIs were referenced by a
numerical ID. These days a string is used instead and the defines are
unused.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new flag bit SND_SOC_TPLG_LNK_FLGBIT_VOICE_WAKEUP to link flags.
If a link is used for voice wake up, users can set this flag bit and
topology will set the link's 'ignore_suspend' to true.
This ABI update is backward compatible.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Code refactoring. These functions and variables are for configuring
physical DAIs, not only backend DAIs since users may not need DPCM.
So remove 'be' from the function names, and rename variables 'be'
to 'd' or 'dai'.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename the ABI struct and type because they are for configuring physical
DAIs, not only backend DAIs since users may not need DPCM:
- Rename struct snd_soc_tplg_be_dai to snd_soc_tplg_dai.
- Rename type SND_SOC_TPLG_TYPE_BE_DAI to SND_SOC_TPLG_TYPE_DAI.
This code refactoring is backward compatible because:
- Both layout of the struct and type value has no change. Kernel can
find the same type value and map to same data layout.
- This struct is not in ABI v4 at all. Now the user space uses ABI v4.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just code refactoring. The function soc_tplg_link_create() will
create a front end link, not a physical link. So rename it to
soc_tplg_fe_link_create().
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology will find an existing physical link (including BE link for
DPCM) by checking its ID, name and stream name, and configure its physical
audio format and flags.
This support is backward compatible for old ABI v4.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Define the API to find an existing DAI link of the soc card by matching
the ID, name and stream name.
Some cards may use unique ID for each DAI link, so matching ID is enough,
and name or stream name are not necessary. But user need to specify name
or stream name as well if not sure whether link ID is unique since most
cards use 0 as the default link ID.
Topology can use this API to find an existing BE link and configure it.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch renames msm8916_wcd_digital_parse_dt() to
msm8916_wcd_digital_get_clks() as the function is not directly dealing
with dt parsing.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the code which is not parsing dt from pm8916_wcd_analog_parse_dt()
to make it clear to reader.
No functional changes done.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 integrated codec has a stereo "Line In" input. Add support for
it to the playback paths.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with different register offsets. The analog paths are very
different. There are more inputs and outputs. The ADC mux has been
replaced with a proper mixer.
This patch adds support for the basic playback path of the A31 codec,
from the DAC to the headphones. Headphone detection, microphone,
signaling, other inputs/outputs and capture will be added later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the DMA engine API documentation, maxburst denotes the
largest possible size of a single transfer, so as not to overflow
destination FIFOs as explained in this excerpt from dmaengine.h
* @src_maxburst: the maximum number of words (note: words, as in
* units of the src_addr_width member, not bytes) that can be sent
* in one burst to the device. Typically something like half the
* FIFO depth on I/O peripherals so you don't overflow it. This
* may or may not be applicable on memory sources.
* @dst_maxburst: same as src_maxburst but for destination target
* mutatis mutandis.
The TX FIFO is 64 samples deep for stereo, and the RX FIFO is 16
samples deep. So maxburst could be 32 and 8 for TX and RX respectively.
Unfortunately the sunxi DMA controller driver takes maxburst as
the requested burst size, rather than a limit, and returns an error
for unsupported values. The original value was 4, but some later
SoCs do not officially support this burst size.
This patch increases maxburst on the TX side to 8, which is supported
by all variants of the sunxi DMA controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with just different register offsets. The analog paths are
very different. There are more inputs and outputs.
The A31s, A23, and H3 have a similar PCM interface, again with register
offsets slightly rearranged. The analog path controls, while very
similar between them and the A31, have been moved a separate bus which
is accessed through a message box like interface in the PRCM address
range. This would be handled by a separate auxiliary device tied in
through the device tree in its supporting create_card function.
The quirks structure is expanded to include different register offsets
and separate callbacks for creating the ASoC card. The regmap_config,
quirks, and of_device_match tables have been moved to facilitate this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This revises existing comments in the register definition macros
section, and adds a few more, so that readers can clearly identify
the types of control registers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio codec on later Allwinner SoCs have a different layout and
audio path compared to the A10/A20. However the PCM parts are still
the same.
The different layout and audio paths mean we need a different
create_card function for different families, so they can create
DAPM endpoint widgets and routes.
This patch moves the regmap configs, quirks and of_device_id
structures to just before the probe function, so we can, among other
things, include a pointer for the create_card function. None of the
lines of code were changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For device opened/closed, we check the D0i3 capability for the device
and invoke skl_tplg_d0i3_get/put, which counts the use case based on the
mode supported.
These counters are then used to decide if the device can enter D0i3 mode
of streaming or non-streaming or no D0i3.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Not all use cases can support Doi3. Only certain use cases like hot word
detection, deep buffering can support D0i3 based on resource requirement.
So, pass the D0i3 capability for the FE/BE copier using topology. This will
be used to take a decision for D0i3 mode entry/exit.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For D0i3, we need to tell DSP to run the pipelines in LP mode. This
information is kept in topology and passed to driver as an attribute
for pipe.
So add a new tuple for lpmode and program the pipe based on value set.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver needs two DSP callback, one to set D0i0 (active) and D0i3
(low-power) states.
Add these callbacks in dsp ops and implement them for broxton platforms.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To set the controller in D0i3 mode, the driver needs to set D0i3C
register after DSP is quiesced. Since the D0iX entry/exit is done by IPC,
add this as callback so that it can be invoked from IPC module.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio DSP supports intermediate power states between D0 and D3
states. These states are D0i0 and D0i3 states.
Collectively we refer these two states as D0iX states.
To set or wake up from these states, driver also needs to send an IPC "Set D0iX
IPC" before doing anything else.
Add support for this new IPC messages.
Signed-off-by: Pardha Saradhi K <pardha.saradhi.kesapragada@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the DSP is in low power mode, it needs to be woken up by a "wake" IPC
to set it into the D0 state before we can send any other IPC command.
The call flow is that the driver calls sst_ipc_tx_message_wait() to send any
IPC and this call checks if the device is in low power mode and in that
case we need to send the wake IPC.
So add a new IPC nopm variant which can be called from driver and
doesn't check for power state (as we already know that) and avoids
circular dependency of again checking power state.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2s driver was only implementing playback for now. Implement capture to
make sure that's not a limitation anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the remaining update to PCM ABI object of version 5.
The flags will be applied to FE (Front End) links and can also be used
by physical links. The private data is reserved for future extension, so
offset update will add the private data size.
Now user space is using ABI v4, and the previous patch "ASoC: topology:
make PCM backward compatible from ABI v4" can assure the backward
compatibility.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Users start to use topology ABI from v4. ABI v5 updated existing manifest
and PCM elements. Two previous patches can support these ABI updates in a
backward compatible way. So if the topology file from user space is
generated by ABI v4, kernel will no longer quit but continue parsing.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
User space may not always set a valid FE DAI driver's name, FE DAI link's
name, stream name or cpu DAI name. In such cases, there are all ZERO in
these name string buffers of a topology PCM object. This patch will only
duplicate valid name strings for kernel FE DAI driver and DAI link when
creating them from topology, and free the name strings when destroying
them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for old version 4 of PCMs (FE DAI & DAI links).
Topology ABI v5 added new fields to stream caps and thus changed PCMs.
Since user space may still uses v4, kernel will check the ABI version by
comparing the object size. If user space uses v4 of PCMs, kernel will
create the latest version of PCMs from the old version, and use the new
version internally to create FE DAI & DAI links. Because these new created
PCM elements will be freed later, kernel need duplicate the name strings
of DAI driver and DAI links when creating them.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add depends on HAS_DMA to Kconfig. This fixes error reported
by kbuild test robot when building for ARCH=m32r:
ERROR: "bad_dma_ops" [sound/soc/bcm/snd-soc-cygnus.ko] undefined!
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While DAPM is mono or single channel, its controls can be shared between
widgets, such as sharing one stereo mixer control between the left and
right channel widgets. An example such as the following routes
[Line In Left]----------<Line In Playback Switch>-------[Left Mixer]
^
^ ^ | ^
(inputs) (paths) <shared stereo mixer control> (outputs)
v v | v
v
[Line In Right]---------<Line In Playback Switch>-------[Right Mixer]
where we have separate widgets and paths for the left and right channels
from "Line In" to "Mixer", but a shared stereo mixer control for the
2 paths.
This patch introduces support for such shared mixer controls, allowing
more than 1 path to be attached to a single stereo control, and being
able to control left/right channels independently.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support double channel shared controls split across 2 registers, one
for each channel, we must be able to update both registers together.
Add a second set of register fields to struct snd_soc_dapm_update, and
update the DAPM control writeback (put) callbacks to support this.
For codecs that use custom events which call into DAPM to do updates,
also clear struct snd_soc_dapm_update before using it, so the second
set of fields remains clean.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes a build error as below which appeared after merging
branch fix/samsung and also proper error messages are restored.
sound/soc/samsung/s3c24xx-i2s.c: In function ‘s3c24xx_iis_dev_probe’:
sound/soc/samsung/s3c24xx-i2s.c:444:8: error: ‘pdata’ undeclared (first use in this function)
sound/soc/samsung/s3c24xx-i2s.c:444:8: note: each undeclared identifier is reported only once for each function it appears in
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes issues introduced in commit 73f5dfc683
"ASoC: samsung: get access to DMA engine early to defer probe properly"
and indicated by a following compilation warning:
CC [M] sound/soc/samsung/spdif.o
sound/soc/samsung/spdif.c: In function ‘spdif_probe’:
sound/soc/samsung/spdif.c:419:6: warning: ‘filter’ may be used uninitialized
in this function [-Wuninitialized]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AC97 drivers are broken and it seems these have not been used
for a long time. This patch removes the unused code, i.e. Samsung
SoC AC97 controller driver and related machine drivers:
ln2440sbc_alc650, smdk2443_wm9710, smdk_wm9713.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to report the resource request error in
the driver as it is already handled within devm_ioremap_resource().
While at it also drop a redundant variable initialization.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This simplifies the code a bit and removes a hard coded IO memory
region size.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the current probe function the GPIO is acquired after the codec's
bus clock is enabled. However if it fails to acquire the GPIO due to
a deferred probe, it does not disable the bus clock before bailing out.
This would result in the clock being enabled multiple times.
Move the code that enables the bus clock after the part that gets the
GPIO, maintaining a separation between resource acquisition and device
enablement in the probe function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleans up usage of wrdma_ch and rdma_ch variables into a
common variable dma_ch, As there is no real use of tracking the dma
channel in two different variables based on stream direction.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds module licence to lpass-cpu driver, without this
patch lpass-cpu module would taint with below error:
snd_soc_lpass_cpu: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
snd_soc_lpass_cpu: Unknown symbol regmap_write (err 0)
snd_soc_lpass_cpu: Unknown symbol devm_kmalloc (err 0)
...
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes lpass-platform driver which was broken in v4.9-rc1.
lpass_pcm_data data structure holds information specific to stream.
Holding a single private pointer to it in global lpass_data
will not work, because it would be overwritten by for each pcm instance.
This code was breaking playback when we have both playback and capture
pcm streams, as playback settings are over written by capture settings.
Fix this by moving channel allocation logic out of pcm_new to pcm_open
so that we can store the stream specific information in private_data of
snd_pcm_runtime.
Fixes: 6adcbdcd4b ("ASoC: lpass-platform: don't use snd_soc_pcm_set_drvdata()")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When sun4i_codec_create_card fails, we do not assign a proper error
code to the return value. The return value would be 0 from the previous
function call, or we would have bailed out sooner. This would confuse
the driver core into thinking the device probe succeeded, when in fact
it didn't, leaving various devres based resources lingering.
Make the create_card function pass back a meaningful error code, and
assign it to the return value.
Fixes: 45fb6b6f2a ("ASoC: sunxi: add support for the on-chip codec on
early Allwinner SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes the following sparse warnings:
sound/soc/codecs/wm8580.c:988:33: warning:
symbol 'wm8580_data' was not declared. Should it be static?
sound/soc/codecs/wm8580.c:992:33: warning:
symbol 'wm8581_data' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for old version 4 of manifest.
Topology ABI v5 added new fields to manifest while user space may still
uses v4. So kernel will check the ABI version by comparing the object
size. If user space uses v4 of manifest, kernel will create a latest
version of manifest from the old one, and use the new one internally and
free it later.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mono ADC Capture Switch control is missing in the driver. So, add it.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove cpu/codec pointer check from asoc_simple_card_canonicalize_dailink()
This is verbose check, and will be issue if CPU name was created by
fmt_single_name() on simple-scu-card.c.
see also asoc_simple_card_canonicalize_cpu()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple sound card family are using very similar style, but because of its
historical reason, there are small differences. For example pointer style,
function name, caller postion etc...
This patch synchronizes style to other simple card family so that be enable
to easy reviewing.
This patch uses dai_link/dai_props instead of links/props.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple sound card family are using very similar style, but because of its
historical reason, there are small differences. For example pointer style,
function name, caller postion etc...
This patch synchronized simple card style to other simple card family
This patch renames asoc_simple_card_priv to simple_card_data,
same as other simple card family.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
simple sound card family are using very similar style, but because of its
historical reason, there are small differences. For example pointer style,
function name, caller postion etc...
This patch synchronized simple card style to other simple card family
Current simple-scu-card function naming is different from other simple card
family. And related to it, the necessary operation position is also
different. This patch synchronize these to other simple card family.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current register name of "SSICKR" was came from R-Car Gen1
which is very old style. It is called as "BRGCKR" on R-Car Gen2/Gen3.
Let's rename it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers support power modes which can't communicate using IPC.
So add a callback to check and wake DSP before sending IPC and then put
to sleep if it is in these power modes.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a DAI specifies "#sound-dai-cells = <0>" in device-tree then
hdmi_of_xlate_dai_name() will be called with zero args, which it isn't
implemented to cope with. The resulting use of an uninitialised variable
for the id will usually result in an error like:
asoc-simple-card sound: parse error -11
asoc-simple-card: probe of sound failed with error -11
Fix this by using and id of zero if no arg is provided.
Fixes: 9731f82d60 ("ASoC: hdmi-codec: enable multi probe for same device")
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
