As in "Function parameters" at doc-guide/kernel-doc.rst, "the
continuation of the description should start at the same column as the
previous line". Make the @producer_pixfmt comply with that.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As a more complete version of vimc_streamer_s_streamer comment was added
at "media: vimc: stream: add missing function documentation" commit in
.c file, remove the old documentation from .h file.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert this driver to use struct v4l2_fh and as a result switch to
using vb2/v4l2_mem2mem helper functions as well.
Only compile-tested due to lack of hardware. This driver is however
very similar to the m2m-deinterlace driver in this respect, and that
v4l2_fh conversion has been properly tested.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver is one of the few that is still not using struct
v4l2_fh. Convert it.
Tested on a Pandaboard.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Convert this driver to use struct v4l2_fh and as a result switch to
using vb2/v4l2_mem2mem helper functions as well.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If CONFIG_VIDEO_V4L2_SUBDEV_API is not set, then it is still possible
to call set_fmt for V4L2_SUBDEV_FORMAT_TRY, the result is just not
stored. So return 0 instead of -ENOTTY.
Calling get_fmt with V4L2_SUBDEV_FORMAT_TRY should return -EINVAL
instead of -ENOTTY, after all the get_fmt functionality is still
present, just not supported for TRY.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This is rougly equivalent to ca0e68e21a (drm/prime: skip CPU sync
in map/unmap dma_buf). The contig memory allocated is already device
coherent memory, so there is no point in doing a CPU sync when
mapping it to another device. Also most importers currently cache
the mapping so the CPU sync would only happen on the first import,
so we are better off with not pretending to do a cache synchronization
at all.
This gets rid of a lot of CPU overhead in uses where those dma-bufs
are regularily imported and detached again, like Weston is currently
doing in the DRM compositor.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch warnings]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable value is being assigned with a value that is never
read and it is being updated later with a new value. The
assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The call to of_get_parent returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/ti-vpe/cal.c:1621:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1607, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/media/platform/exynos4-is/fimc-is.c:813:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/fimc-is.c:870:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/fimc-is.c:885:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 807, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:545:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 541, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:528:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function.
drivers/media/platform/exynos4-is/media-dev.c:534:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 499, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Building a KASAN-enabled kernel with clang ends up in a case where too
much is inlined into vivid_thread_vid_cap() and the stack usage grows
a lot, possibly when the register allocation fails to produce efficient
code and spills a lot of temporaries to the stack. This uses more
than twice the amount of stack than the sum of the individual functions
when they are not inlined:
drivers/media/platform/vivid/vivid-kthread-cap.c:766:12: error: stack frame size of 2208 bytes in function 'vivid_thread_vid_cap' [-Werror,-Wframe-larger-than=]
Marking two of the key functions in here as 'noinline_for_stack' avoids
the pathological case in clang without any apparent downside for gcc.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit 8c0d3a02c1 ("PCI: Add accessors for PCI Express Capability")
added accessors for the PCI Express Capability so that drivers didn't
need to be aware of differences between v1 and v2 of the PCI
Express Capability.
Replace pci_read_config_word() and pci_write_config_word() calls with
pcie_capability_read_word() and pcie_capability_write_word().
Signed-off-by: Frederick Lawler <fred@fredlawl.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The patch fixes various v4l2-compliance failures:
- missing support for control events
- support of s/g_std even though this doesn't apply to a webcam
- missing colorspace reporting
- bus_info wasn't filled in by VIDIOC_QUERYCAP
- parm.capture.readbuffers was overridden with wrong value
- viacam_enum_framesizes/intervals didn't check the arguments
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If CONFIG_VIDEO_V4L2_SUBDEV_API is not set, then it is still possible
to call set_fmt for V4L2_SUBDEV_FORMAT_TRY, the result is just not
stored. So return 0 instead of -ENOTTY.
Calling get_fmt with V4L2_SUBDEV_FORMAT_TRY should return -EINVAL
instead of -ENOTTY, after all the get_fmt functionality is still
present, just not supported for TRY.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Modern V4L2 drivers should use struct v4l2_fh to represent a filehandle.
This driver was one of the few that didn't use it.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The power management hooks were never unregistered, which caused a
crash when unloading the module.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Probable cut&paste typo - use the correct field size.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Probable cut&paste typo - use the correct field size.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The variable data is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the Amlogic SM1 SoC Family to the G12A AO-CECB
derivative.
It only adds a single init register.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[hverkuil-cisco@xs4all.nl: dropped spurious newline]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver builds fine without these, and they cause build
problems once davinci multiplatform support is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There is a potential integer overflow when int 2 is left shifted
as this is evaluated using 32 bit arithmetic but is being used in
a context that expects an expression of type s64. Fix this by
generating a mask using GENMASK to avoid a 32 bit overflow.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 8a99e9faa1 ("media: vivid: add HDMI (dis)connect RX emulation")
Fixes: 79a792dafa ("media: vivid: add HDMI (dis)connect TX emulation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The priv field of struct v4l2_pix_format shouldn't be set by drivers,
it's set by the v4l2 core instead to V4L2_PIX_FMT_PRIV_MAGIC.
Drop this from the few media drivers that still do this.
Note that the gspca patch is slightly more involved since some of the
sub-gspca drivers use the priv field internally.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[hverkuil-cisco@xs4all.nl: fix clash in gspca between priv arg and priv variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When reaching the end of stream, V4L2 m2m clients may expect the
V4L2_EOS_EVENT. Although the V4L2_EOS_EVENT is deprecated behavior,
drivers must signal that event before dequeuing the buffer that has the
V4L2_BUF_FLAG_LAST flag set.
If a driver queues the V4L2_EOS_EVENT event and returns the buffer after
the check for events but before the check for buffers, vb2_m2m_poll()
will signal that the buffer with V4L2_BUF_FLAG_LAST can be read but not
that the V4L2_EOS_EVENT is available.
Split the check for buffers into a separate function and check for
available buffers before checking for events. This ensures that if
vb2_m2m_poll() signals POLLIN | POLLRDNORM for the V4L2_BUF_FLAG_LAST
buffer, it signals POLLPRI for the V4L2_EOS_EVENT, too.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When reaching the end of stream, V4L2 clients may expect the
V4L2_EOS_EVENT before being able to dequeue the last buffer, which has
the V4L2_BUF_FLAG_LAST flag set.
If the vb2_poll() function first checks for events and afterwards if
buffers are available, a driver can queue the V4L2_EOS_EVENT event and
return the buffer after the check for events but before the check for
buffers. This causes vb2_poll() to signal that the buffer with
V4L2_BUF_FLAG_LAST can be read without the V4L2_EOS_EVENT being
available.
First, check for available buffers and afterwards for events to ensure
that if vb2_poll() signals POLLIN | POLLRDNORM for the
V4L2_BUF_FLAG_LAST buffer, it also signals POLLPRI for the
V4L2_EOS_EVENT.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function v4l_pix_format_touch() is called for S_FMT to set
v4l2_pix_format fields to default values for a v4l-touch device,
but it wasn't called for TRY_FMT. Add this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get_conn, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ettore Chimenti <ek5.chimenti@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use cec_notifier_cec_adap_(un)register instead of
cec_notifier_get_conn, cec_notifier_put and cec_register_cec_notifier.
Also enable the CEC_CAP_CONNECTOR_INFO capability.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the new cec_notifier_cec_adap_(un)register() functions to
(un)register the notifier for the CEC adapter.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds support for the "Mygica T230C v2" to the dvbsky driver.
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Tested-by: Frank Rysanek <Frantisek.Rysanek@post.cz>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The T230C v2 hardware needs a mode of the si2168 chip to be
set for which the si2168 driver previously had no support.
This patch uses a specific measure to configure this on the
T230C v2 hardware only - see the flag passed via the ts_mode
attribute and its dependency on USB_PID_MYGICA_T230C2.
Signed-off-by: Jan Pieter van Woerkom <jp@jpvw.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch schedules a USB reset device call following a USB clear
halt error. The issues solved, and patch implementation,
are similar to those found in
drivers/hid/usbhid/hid-core.c.
As seen on very rare occasions approximately one time per month
(mceusb device 2304:0225 in this sample)
Jul 27 2018 15:09:39
[59388.696941] mceusb 1-1.1.2:1.0: Error: urb status = -32 (RX HALT)
[59388.698838] mceusb 1-1.1.2:1.0: rx clear halt error -32
the device can get into RX or TX HALT state where usb_clear_halt()
also fails and also returns -EPIPE (HALT/STALL). After which, all
further mceusb device control and data I/O always fail with HALT/STALL.
Subsequently, the entire mceusb device no longer functions.
Cause and problem replication conditions remain unknown.
Further troubleshooting reveals usb_reset_device()
restores mceusb device operation.
Patch test 1:
Hot unplugging the mceusb device triggers USB RX HALT and
USB clear halt errors. A mceusb_dev_disconnect() call follows unplug.
This patch's reset device call invokes an extra
mceusb_dev_probe()
mceusb_dev_disconnect()
cycle, before the mceusb driver detaches.
The additional probe/disconnect verifies the patch's device reset
code executed.
But note this patch is for USB clear halt error cases not caused by
unplugging the mceusb device.
Patch test 2:
Simulate a RX HALT and a clear halt error with instrumented code in
the driver.
Jul 12 2019 19:41:18
[522745.263104] mceusb 1-1.3:1.0: set rx halt retval, 0
[522745.263943] mceusb 1-1.3:1.0: Error: rx urb status = -32 (RX HALT)
[522745.263970] mceusb 1-1.3:1.0: kevent 1 scheduled
[522745.264016] mceusb 1-1.3:1.0: kevent handler called (flags 0x2)
[522745.272883] mceusb 1-1.3:1.0: rx clear halt status = 0
[522745.272917] mceusb 1-1.3:1.0: stuck RX HALT state requires USB Reset Device to clear
[522745.273005] mceusb 1-1.3:1.0: mceusb_dev_disconnect called
[522745.702815] usb 1-1.3: reset full-speed USB device number 14 using dwc_otg
[522745.836812] mceusb 1-1.3:1.0: mceusb_dev_probe called
[522745.836823] mceusb 1-1.3:1.0: acceptable bulk inbound endpoint found
[522745.836832] mceusb 1-1.3:1.0: acceptable bulk outbound endpoint found
...
The result matches what is expected when the device gets into
a real rx clear halt error case by itself.
This is the same sequence of messages when manually invoking
the ./usbreset command line utility with an unpatched mceusb driver.
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When CONFIG_DVB_DIB9000 is disabled, we can still compile code that
now fails to link against dibx000_i2c_set_speed:
drivers/media/usb/dvb-usb/dib0700_devices.o: In function `dib01x0_pmu_update.constprop.7':
dib0700_devices.c:(.text.unlikely+0x1c9c): undefined reference to `dibx000_i2c_set_speed'
The call sites are both through dib01x0_pmu_update(), which gets passed
an 'i2c' pointer from dib9000_get_i2c_master(), which has returned
NULL. Checking this pointer seems to be a good idea anyway, and it avoids
the link failure in most cases.
Sean Young found another case that is not fixed by that, where certain
gcc versions leave an unused function in place that causes the link error,
but adding an explict IS_ENABLED() check also solves this.
Fixes: b7f54910ce ("V4L/DVB (4647): Added module for DiB0700 based devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ensure we do not access the buffer beyond the end if no 0xff byte
is encountered.
Reported-by: syzbot+eaaaf38a95427be88f4b@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The rc-mm protocol can't be decoded by the mtk-cir since the de-glitch
filter removes pulses/spaces shorter than 294 microseconds.
Tested on a BananaPi R2.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
RC_PROTO_BIT_ALL includes protocols like unknown and other that do not
have IR decoders by definition. If these protocols are set in the
allowed_protocols, they will show in the protocols sysfs file but cannot
be enabled.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Only one field needs to be validated: 'num_dct_parts'.
This field is used to iterate over the user-provided array
'dct_part_sizes'.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
[hverkuil-cisco@xs4all.nl: s -> (s) in zero_padding macro]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the parsed VP8 frame pixel format and controls, to be used
with the new stateless decoder API for VP8 to provide parameters
for accelerator (aka stateless) codecs.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework std_validate moving the compound controls to
its own validation function.
While here, fix the pointer math to account the index parameter.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The device_caps in struct video_device are already set correctly,
so there is no need to set them in querycap again.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2 core sets the format description and flags for the driver in order
to ensure consistent naming.
So drop the strscpy of the description in drivers. Also remove any
description strings in driver-internal structures since those are
no longer needed.
And in am437x-vpfe.c drop an unnecessary f->type assignment in
vpfe_enum_fmt().
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[hverkuil-cisco@xs4all.nl: addressed some small suggestions from Laurent]
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2 core sets the description for the driver in order to ensure
consistent naming.
So drop the strscpy of the description in drivers. Also remove any
description strings in driver-internal structures since those are
no longer needed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The V4L2 core sets the description for the driver in order to ensure
consistent naming.
So drop the strscpy of the description in drivers. Also remove any
description strings in driver-internal structures since those are
no longer needed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l_fill_fmtdesc() is supposed to be updated whenever a new pixelformat
is added, but a bunch of recently added pixelformats were forgotten.
Update the list.
Also change a few lower case words to upper case to keep the same style.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[hverkuil-cisco@xs4all.nl: changed 1-5-5-5 to 5-5-5-1 as per Laurent's suggestion]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----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=ZxJh
-----END PGP SIGNATURE-----
Merge tag 'media/v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For two regressions in media core:
- v4l2-subdev: fix regression in check_pad()
- videodev2.h: change V4L2_PIX_FMT_BGRA444 define: fourcc was already
in use"
* tag 'media/v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: videodev2.h: change V4L2_PIX_FMT_BGRA444 define: fourcc was already in use
media: v4l2-subdev: fix regression in check_pad()
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0006weHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGaDUIAJ4oTyVWpMRZkfG6
vVY8qVMU3zlzEqRiyLYjkXoe/mGpuU/UVTyyStllxZ+Gg9da0mGwlugScKriPJof
4KRUDDTGX5DrfEOo+0brKvM+PYh9uGViPgKXzyv7i6BrnX2z3JdBR4bKNuEYlAJ9
N93Qg7v05SBHIq2Gfp3klrdWbsTTW2EaDTLbcgifXLnfKyFr47kwsmXAHPlTFP0p
dYsZHHmf14Y9n1+ToZeVINgjQFr6mFn6ygY/PqTnd6vCgEEfP9eENJ4BZCtN1ZL/
V0BO9MyJ5iZV0AfwSEKydk+kDEvO16TG/nyDrECVuur7AXsBx18ZplVc787f6GK+
dyCQJ3U=
=XLAF
-----END PGP SIGNATURE-----
Merge tag 'v5.3-rc1' into patchwork
Linus 5.3-rc1
* tag 'v5.3-rc1': (12816 commits)
Linus 5.3-rc1
iommu/amd: fix a crash in iova_magazine_free_pfns
hexagon: switch to generic version of pte allocation
typo fix: it's d_make_root, not d_make_inode...
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
dt-bindings: iio: ad7124: Fix dtc warnings in example
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
dt-bindings: Ensure child nodes are of type 'object'
x86/entry/64: Prevent clobbering of saved CR2 value
smp: Warn on function calls from softirq context
KVM: x86: Add fixed counters to PMU filter
KVM: nVMX: do not use dangling shadow VMCS after guest reset
KVM: VMX: dump VMCS on failed entry
KVM: x86/vPMU: refine kvm_pmu err msg when event creation failed
KVM: s390: Use kvm_vcpu_wake_up in kvm_s390_vcpu_wakeup
KVM: Boost vCPUs that are delivering interrupts
KVM: selftests: Remove superfluous define from vmx.c
...
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
sd->entity.graph_obj.mdev can be NULL when this function is called, and
that breaks existing drivers (rcar-vin, but probably others as well).
Check if sd->entity.num_pads is non-zero instead since that doesn't depend
on mdev.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Fixes: a8fa55078a ("media: v4l2-subdev: Verify arguments in v4l2_subdev_call()")
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with other
trees, unfortunately. He has a lot more of these waiting on the wings
that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos, and one
on Spectre vulnerabilities.
- Various improvements to the build system, including automatic markup of
function() references because some people, for reasons I will never
understand, were of the opinion that :c:func:``function()`` is
unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc.
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEIw+MvkEiF49krdp9F0NaE2wMflgFAl0krAEPHGNvcmJldEBs
d24ubmV0AAoJEBdDWhNsDH5Yg98H/AuLqO9LpOgUjF4LhyjxGPdzJkY9RExSJ7km
gznyreLCZgFaJR+AY6YDsd4Jw6OJlPbu1YM/Qo3C3WrZVFVhgL/s2ebvBgCo50A8
raAFd8jTf4/mGCHnAqRotAPQ3mETJUk315B66lBJ6Oc+YdpRhwXWq8ZW2bJxInFF
3HDvoFgMf0KhLuMHUkkL0u3fxH1iA+KvDu8diPbJYFjOdOWENz/CV8wqdVkXRSEW
DJxIq89h/7d+hIG3d1I7Nw+gibGsAdjSjKv4eRKauZs4Aoxd1Gpl62z0JNk6aT3m
dtq4joLdwScydonXROD/Twn2jsu4xYTrPwVzChomElMowW/ZBBY=
=D0eO
-----END PGP SIGNATURE-----
Merge tag 'docs-5.3' of git://git.lwn.net/linux
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
- remove fbdev notifier usage for fbcon (as prep work to clean up the fbcon
locking), add locking checks in vt/console code and make assorted cleanups
in fbdev and backlight code (Daniel Vetter)
- add COMPILE_TEST support to atmel_lcdfb, da8xx-fb, gbefb, imxfb, pvr2fb and
pxa168fb drivers (me)
- fix DMA API abuse in au1200fb and jz4740_fb drivers (Christoph Hellwig)
- add check for new BGRT status field rotation bits in efifb driver (Hans de
Goede)
- mark expected switch fall-throughs in s3c-fb driver (Gustavo A. R. Silva)
- remove fbdev mxsfb driver in favour of the drm version (Fabio Estevam)
- remove broken rfbi code from omap2fb driver (me)
- misc fixes (Arnd Bergmann, Shobhit Kukreti, Wei Yongjun, me)
- misc cleanups (Gustavo A. R. Silva, Colin Ian King, me)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W1AD
-----END PGP SIGNATURE-----
Merge tag 'fbdev-v5.3' of git://github.com/bzolnier/linux
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
- remove fbdev notifier usage for fbcon (as prep work to clean up the
fbcon locking), add locking checks in vt/console code and make
assorted cleanups in fbdev and backlight code (Daniel Vetter)
- add COMPILE_TEST support to atmel_lcdfb, da8xx-fb, gbefb, imxfb,
pvr2fb and pxa168fb drivers (me)
- fix DMA API abuse in au1200fb and jz4740_fb drivers (Christoph
Hellwig)
- add check for new BGRT status field rotation bits in efifb driver
(Hans de Goede)
- mark expected switch fall-throughs in s3c-fb driver (Gustavo A. R.
Silva)
- remove fbdev mxsfb driver in favour of the drm version (Fabio
Estevam)
- remove broken rfbi code from omap2fb driver (me)
- misc fixes (Arnd Bergmann, Shobhit Kukreti, Wei Yongjun, me)
- misc cleanups (Gustavo A. R. Silva, Colin Ian King, me)
* tag 'fbdev-v5.3' of git://github.com/bzolnier/linux: (62 commits)
video: fbdev: imxfb: fix a typo in imxfb_probe()
video: fbdev: s3c-fb: Mark expected switch fall-throughs
video: fbdev: s3c-fb: fix sparse warnings about using incorrect types
video: fbdev: don't print error message on framebuffer_alloc() failure
video: fbdev: intelfb: return -ENOMEM on framebuffer_alloc() failure
video: fbdev: s3c-fb: return -ENOMEM on framebuffer_alloc() failure
vga_switcheroo: Depend upon fbcon being built-in, if enabled
video: fbdev: omap2: remove rfbi
video: fbdev: atmel_lcdfb: remove redundant initialization to variable ret
video: fbdev-MMP: Use struct_size() in devm_kzalloc()
video: fbdev: controlfb: fix warnings about comparing pointer to 0
efifb: BGRT: Add check for new BGRT status field rotation bits
jz4740_fb: fix DMA API abuse
video: fbdev: pvr2fb: fix link error for pvr2fb_pci_exit
video: fbdev: s3c-fb: add COMPILE_TEST support
video: fbdev: imxfb: fix sparse warnings about using incorrect types
video: fbdev: pvr2fb: fix build warning when compiling as module
fbcon: Export fbcon_update_vcs
backlight: simplify lcd notifier
staging/olpc_dcon: Add drm conversion to TODO
...
-----BEGIN PGP SIGNATURE-----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=ABgl
-----END PGP SIGNATURE-----
Merge tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new Atmel microship ISC driver
- coda has gained support for mpeg2 and mpeg4
- cxusb gained support for analog TV
- rockchip staging driver was split into two separate staging drivers
- added a new staging driver for Allegro DVT video IP core
- added a new staging driver for Amlogic Meson video decoder
- lots of improvements and cleanups
* tag 'media/v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (398 commits)
media: allegro: use new v4l2_m2m_ioctl_try_encoder_cmd funcs
media: doc-rst: Fix typos
media: radio-raremono: change devm_k*alloc to k*alloc
media: stv0297: fix frequency range limit
media: rc: Prefer KEY_NUMERIC_* for number buttons on remotes
media: dvb_frontend: split dvb_frontend_handle_ioctl function
media: mceusb: disable "nonsensical irdata" messages
media: rc: remove redundant dev_err message
media: cec-notifier: add new notifier functions
media: cec: add struct cec_connector_info support
media: cec-notifier: rename variables, check kstrdup and n->conn_name
media: MAINTAINERS: Add maintainers for Media Controller
media: staging: media: tegra-vde: Defer dmabuf's unmapping
media: staging: media: tegra-vde: Add IOMMU support
media: hdpvr: fix locking and a missing msleep
media: v4l2: Test type instead of cfg->type in v4l2_ctrl_new_custom()
media: atmel: atmel-isc: fix i386 build error
media: v4l2-ctrl: Move compound control initialization
media: hantro: Use vb2_get_buffer
media: pci: cx88: Change the type of 'missed' to u64
...
Change devm_k*alloc to k*alloc to manually allocate memory
The manual allocation and freeing of memory is necessary because when
the USB radio is disconnected, the memory associated with devm_k*alloc
is freed. Meaning if we still have unresolved references to the radio
device, then we get use-after-free errors.
This patch fixes this by manually allocating memory, and freeing it in
the v4l2.release callback that gets called when the last radio device
exits.
Reported-and-tested-by: syzbot+a4387f5b6b799f6becbf@syzkaller.appspotmail.com
Signed-off-by: Luke Nowakowski-Krijger <lnowakow@eng.ucsd.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: cleaned up two small checkpatch.pl warnings]
[hverkuil-cisco@xs4all.nl: prefix subject with driver name]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There was a typo at the lower frequency limit for a DVB-C
card, causing the driver to fail while tuning channels at the
VHF range.
https://bugzilla.kernel.org/show_bug.cgi?id=202083
Fixes: f1b1eabff0 ("media: dvb: represent min/max/step/tolerance freqs in Hz")
Reported-by: Ari Kohtamäki <ari.kohtamaki@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Prefer KEY_NUMERIC_* for number buttons on remotes. Now all the remotes
use KEY_NUMERIC_[0-9] for the number buttons rather than keys that
could be affected by modifiers (Caps-Lock, or Num-Lock) or regional
keymaps.
Created using:
sed -i 's/KEY_\([0-9]\) /KEY_NUMERIC_\1 /' *.c
sed -i 's/KEY_\([0-9]\)}/KEY_NUMERIC_\1}/' *.c
sed -i 's/``KEY_\([0-9]\)/``KEY_NUMERIC_\1/' Documentation/media/uapi/rc/rc-tables.rst
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Over time, dvb_frontend_handle_ioctl() has grown to the point where
we now get a warning from the compiler about excessive stack usage:
drivers/media/dvb-core/dvb_frontend.c: In function 'dvb_frontend_handle_ioctl':
drivers/media/dvb-core/dvb_frontend.c:2692:1: error: the frame size of 1048 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Almost all of this is used by the dtv_frontend_properties structure
in the FE_GET_PROPERTY and FE_GET_FRONTEND commands. Splitting those
into separate function reduces the stack usage of the main function
to just 136 bytes, the others are under 500 each.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to support multiple CEC devices for an HDMI connector,
and to support cec_connector_info, drivers should use either a
cec_notifier_conn_(un)register pair of functions (HDMI drivers)
or a cec_notifier_cec_adap_(un)register pair (CEC adapter drivers).
This replaces cec_notifier_get_conn/cec_notifier_put.
For CEC adapters it is also no longer needed to call cec_notifier_register,
cec_register_cec_notifier and cec_notifier_unregister. This is now
all handled internally by the new functions.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Define struct cec_connector_info in media/cec.h and define
CEC_CAP_CONNECTOR_INFO. In a later patch this will be moved to
uapi/linux/cec.h.
The CEC_CAP_CONNECTOR_INFO capability can be set by drivers, but
cec_allocate_adapter() will remove it again until the public API
for this can be enabled once all drm drivers wire this up correctly.
Also add the cec_fill_conn_info_from_drm and cec_s_conn_info functions,
which are needed by drm drivers to fill in the cec_connector info
based on a drm_connector.
The cec_notifier_(un)register and cec_register_cec_notifier
prototypes were moved from cec-notifier.h to cec.h since cec.h no longer
includes cec-notifier.h. These headers included each other before,
which caused various problems.
Due to these changes the seco-cec driver was changed as well: it
should include cec-notifier.h, not cec.h.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
dev -> hdmi_dev
conn -> conn_name
Check if n->conn_name is not NULL before calling strcmp.
Check the result of kstrdup, and clean up on error.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This driver has three locking issues:
- The wait_event_interruptible() condition calls hdpvr_get_next_buffer(dev)
which uses a mutex, which is not allowed. Rewrite with list_empty_careful()
that doesn't need locking.
- In hdpvr_read() the call to hdpvr_stop_streaming() didn't lock io_mutex,
but it should have since stop_streaming expects that.
- In hdpvr_device_release() io_mutex was locked when calling flush_work(),
but there it shouldn't take that mutex since the work done by flush_work()
also wants to lock that mutex.
There are also two other changes (suggested by Keith):
- msecs_to_jiffies(4000); (a NOP) should have been msleep(4000).
- Change v4l2_dbg to v4l2_info to always log if streaming had to be restarted.
Reported-by: Keith Pyle <kpyle@austin.rr.com>
Suggested-by: Keith Pyle <kpyle@austin.rr.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
cfg->type can be overridden by v4l2_ctrl_fill() and the new value is
stored in the local type var. Fix the tests to use this local var.
Fixes: 0996517cf8 ("V4L/DVB: v4l2: Add new control handling framework")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
[hverkuil-cisco@xs4all.nl: change to !qmenu and !qmenu_int (checkpatch)]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework std_init adding an explicit initialization for
compound controls.
While here, make sure the control is initialized to zero,
before providing default values for all its fields.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Callers of hrtimer_forward_now() should save the return value in u64.
change type of missed from unsigned long to u64.
Signed-off-by: Puranjay Mohan <puranjay12@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: type changed, so %ld -> %llu in printk]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_fill_pixfmt() returns -EINVAL if the pixelformat used as parameter is
invalid or if the user is trying to use a multiplanar format with the
singleplanar API. Currently, the vimc_cap_try_fmt_vid_cap() returns such
value, but vimc_cap_s_fmt_vid_cap() is ignoring it. Fix that and returns
an error value if vimc_cap_try_fmt_vid_cap() has failed.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Suggested-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of filling in the struct v4l2_capability device_caps
field, fill in the struct video_device device_caps field.
That way the V4L2 core knows what the capabilities of the
video device are.
But this only really works if all drivers use this, so convert
all pci drivers in this patch.
Tested with cx88-blackbird and ivtv PVR-350.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Extend parameter checks performed by v4l2_subdev_call() with a check for
a non-NULL pad config pointer if V4L2_SUBDEV_FORMAT_TRY format type is
requested so drivers don't need to care.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Parameters passed to check helpers are now obtained by dereferencing
unverified pointer arguments. Check validity of those pointers first.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Correctness of format type (try or active) and pad number parameters
passed to subdevice operation callbacks is now verified only for IOCTL
calls. However, those callbacks are also used by drivers, e.g., V4L2
host interfaces.
Since both subdev_do_ioctl() and drivers are using v4l2_subdev_call()
macro while calling subdevice operations, move those parameter checks
from subdev_do_ioctl() to v4l2_subdev_call() so we can avoid taking care
of those checks inside drivers.
Define a wrapper function for each operation callback in scope, then
gather those wrappers in a static v4l2_subdev_ops structure so the
v4l2_subdev_call() macro can find them easy if provided.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for dynamically changing the GOP size, bitrate, frame rate,
constant intra quantization parameter, number of intra refresh macro
blocks and slice mode parameters.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Changing slice mode dynamically while encoding will require to calculate
the register value again, so split it out into a separate function.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently the platform device pointer is stored in struct coda_dev,
only to convert it into a device pointer wherever it is used. Just
store the device pointer directly.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If reordering is not enabled, the last decoded frame has to be the last
returned buffer. Otherwise wait for the firmware to report no more
frame to display. In that case the return buffer is the last one as
well, and can be reported as such.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there is still a buffer pending, mark it as the last buffer. It will
create a meta that is flagged as last when the buffer is copied into the
bitstream ring buffer. If there are no more buffers pending, find the
last bitstream meta and mark it as last. If there is no bitstream meta
either, wake up the capture queue as there will be no more decoded
frames.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure that an encoder stop command running concurrently with an
encoder finish_run always either flags the last returned buffer or wakes
up the capture queue to signal the end of stream condition afterwards.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the flagged last output buffer to also flag the corresponding
capture buffer after encoding. This causes the end of stream event
to be issued and the buffer to be dequeued with the last flag set.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there are no pending queued output buffers to be encoded, waking up
the capture queue with -EPIPE signals end of stream. If there are
pending buffers on the other hand, setting the V4L2_BUF_FLAG_LAST on
the resulting encoded capture buffers is all that is needed.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Using the output queue sequence counter to determine the last buffer to
be encoded or decoded always was fragile at best. Now that we have the
last buffer flag propagating from the output queue to the capture queue
correctly, this is not needed anymore.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mark the last output buffer to be encoded.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If there are still queued output buffers pending to be copied into the
bitstream ring buffer, setting the stream end flag should be deferred
until the marked last output buffer is written into the bitstream ring
buffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mark the last output buffer to be decoded and only copy pending queued
output buffers into the bitstream ring buffer in the BIT processor
decoder case.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since V4L2_BUF_FLAG_LAST is a CAPTURE only flag, clear it from OUTPUT
buffers in QBUF and DQBUF. This allows to use the flag internally to
signal the last buffer to decode after a decoder stop command was
issued.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If no more frames are decoded in bitstream end mode, and a previously
decoded frame has been returned, the firmware still increments the frame
number. To avoid a sequence number mismatch after decoder restart,
increment the sequence_offset correction parameter.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The bitstream ringbuffer might be in an underrun state after draining,
or it might still contain unread data if the previous decoder stop
command was flagged as immediate. Flush the bitstream ring buffer
during V4L2_DEC_CMD_START to get into a well defined state. Also fill
the bitstream with buffers that have been queued during draining,
to resume decoding immediately.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On CODA960, sequence initialization can succeed if less than 512 bytes
are ready in the bitstream ring buffer.
On other variants, warn about too small payload in start_streaming.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If the first buffer contains only headers, the sequence initialization
command fails. On CodaHx4 the buffer must be padded to at least 512
bytes, on CODA960 it seems to be enough to just repeat the sequence and
extension headers (MPEG-2) or the VOS and VO headers (MPEG-4) once for
for sequence initialization to succeed without further bitstream data.
On CodaHx4 the headers can be repeated multiple times until the 512 byte
mark is reached.
A similar issue was solved for h.264 by padding with a filler NAL in
commit 0eef89403e ("[media] coda: pad first h.264 buffer to 512
bytes").
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Pass vaddr and size to coda_bitstream_queue instead of a struct
vb2_v4l2_buffer to make it reusable for queueing data that is
not exactly a whole v4l2 buffer into the bitstream ringbuffer.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine the separate auxiliary buffer, buffer meta, frame type, and
decode error arrays into an array of struct coda_internal_frame.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful decoder API requires decoders to signal detection
of stream dimensions via the V4L2_EVENT_SOURCE_CHANGE event.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a sequence initialization work item to be run when OUTPUT buffers
are queued in the initialization state.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sequence initialization already has to happen during the
initialization phase, after headers have been queued on the OUTPUT
queue. This means that sequence initialization has to be queued as
a work item from QBUF on the OUTPUT queue. The internal framebuffer
setup should be done later during VIDIOC_REQBUFS() on the CAPTURE
queue.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When the DEC_CMD_STOP command is issued after the context has already
consumed all the queued buffers, we need to make sure to wake the
destination queue with last_buffer_dequeued set, to allow userspace to
make progress in its EOS handling.
As there might still be picture run workers pending at that point, we
need to synchronize with them, so the sequence number comparison reads
stable values.
reword commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine setting the last_buffer_dequeued flag on the capture video
queue and waking up its done workqueue into a helper function.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
coda_encoder_cmd() is racy, as the last scheduled picture run worker can
still be in-flight while the ENC_CMD_STOP command is issued. Depending
on the exact timing the sequence numbers might already be changed, but
the last buffer might not have been put on the destination queue yet.
In this case the current implementation would prematurely wake the
destination queue with last_buffer_dequeued=true, causing userspace to
call streamoff before the last buffer is handled.
Close this race window by synchronizing with the pic_run_worker before
doing the sequence check.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[l.stach@pengutronix.de: switch to flush_work, reword commit message]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sequence number handling assumed that the BIT processor frame number
starts counting at 1, but this is not true for the MPEG-2 decoder,
which starts at 0. Fix the sequence counter offset detection to handle
this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use mem2mem try_en/decoder_cmd helpers to ensure consistent behaviour
with other video codec drivers.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CMD_START shall be used to start the processing after a drain that
was initiated with CMD_STOP.
Up until now, a drain on coda could only be finished with a
STREAMOFF-STREAMON, which resulted in a reset of the device.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As warned by sparse:
drivers/media/platform/marvell-ccic/cafe-driver.c:475:23: warning: symbol 'ov7670_info' was not declared. Should it be static?
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It's impossible for mmpcam_calc_dphy() to be called without it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Avoid pointlessly calling calc_dphy() when the bus is not
V4L2_MBUS_CSI2_DPHY. This will make it easier to replace the platform data
with devicetree.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support of JPEG pixel format.
This requires auto detection of data type from CSI-2 stream.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ask device connected on sink pad for link frequency
in order to configure CLK_LANE_REG1 (ui_x4).
If not available, ask for pixel rate information to compute it.
This is needed to deal with compressed format such as JPEG
where number of bits per pixel is unknown: computation of
link frequency from pixel rate is not possible.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor needs the MCLK clock running when it's being probed. On
platforms where the sensor is instantiated from a DT (MMP2) it is going
to happen asynchronously.
Therefore, the current modus operandi, where the bridge driver fiddles
with the sensor power and clock itself is not going to fly. As the comments
wisely note, this doesn't even belong there.
Luckily, the ov7670 driver is already able to control its power and
reset lines, we can just drop the MMP platform glue altogether.
It also requests the clock via the standard clock subsystem. Good -- let's
set up a clock instance so that the sensor can ask us to enable the clock.
Note that this is pretty dumb at the moment: the clock is hardwired to a
particular frequency and parent. It was always the case.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
An instance of a sensor on DT-based MMP2 platform is always going to be
created asynchronously.
Let's move the manual device creation away from the core to the Cafe
driver (used on OLPC XO-1, not present in DT) and set up appropriate
async matches: I2C on Cafe, FWNODE on MMP (OLPC XO-1.75).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The platform data is actually not used anywhere (along with the CSI
support) and should be safe to remove.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the names more suitable for devicetree bindings.
There are no board files utilizing this, thus we seem to be at liberty
at renaming this without consequences.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The access to REG_CLKCTRL or REG_CTRL1 without the clock enabled hangs
the machine. Enable the clock first.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove structure members and headers that are not actually used. Saves
us from some noise in subsequent cleanup commits.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This accesses the clock registers directly and thus is going to stay in the
way of making the driver devicetree friendly.
No boards seems to actually use this. If it's somehow actually needed it
needs to be done differently.
This reverts commit 7c269f454e.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the patch refactoring the fw-node, the mt9m111 was broken for all
platform_data based platforms, which were the first aim of this
driver. Only the devicetree platform are still functional, probably
because the testing was done on these.
The result is that -EINVAL is systematically return for such platforms,
what this patch fixes.
[Sakari Ailus: Rework this to resolve a merge conflict and use dev_fwnode]
Fixes: 98480d65c4 ("media: mt9m111: allow to setup pixclk polarity")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The mt9m111_power_on function did not properly clean up whenever it
encountered an error. Do that now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The regulator_get() function returns a regulator when it succeeds. There's
no need to check whether the regulator is NULL later on.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In the soc_camera removal, the board specific power callback was
dropped. This at least will remove the power optimization from ezx and
em-x270 pxa based boards.
As to recreate the same level of functionality, make the mt9m111 have a
regulator providing it its power, so that board designers can plug in a
gpio based or ldo regulator, mimicking their former soc_camera power
hook.
[sakari.ailus@linux.intel.com: fix a build warning]
Fixes: 5c10113cc668 ("media: mt9m111: make a standalone v4l2 subdevice")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
devm_gpiod_get never returns NULL; therefore it's not necessary to check
for that. PTR_ERR(NULL) also yields zero, which is confusing to smatch.
Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
PTR_ERR(NULL) yields 0 which is commonly used to denote success. This is
the case here, and PTR_ERR(NULL) is apparently shunned upon. Fix this by
explicitly returning 0 if fwnode == NULL.
Reported-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Commit c62b96050b ("media: ov6650: Register with asynchronous
subdevice framework") carelessly requested creation of a video device
node by setting a V4L2_SUBDEV_FL_HAS_DEVNODE flag. The driver is not
ready for that as it doesn't implement proper locking required for
serialization of IOCTLs.
Fix it by dropping the flag assignment.
Fixes: c62b96050b ("media: ov6650: Register with asynchronous subdevice framework")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Removed the warning from the following files:
drivers/media/i2c/ov13858.c
drivers/media/i2c/ov2685.c
drivers/media/i2c/ov5695.c
Signed-off-by: Shobhit Kukreti <shobhitkukreti@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set/invalidate physical addresses based on the configuration of the
display present control. This is relevant not only when the display
present control is modified, but also when the Vivid instance EDID is
set/cleared.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CEC adapters and controllers (handlers) are now set up as follows:
1. Allocate CEC adapters: setup of control handlers in next step
requires these adapters to be allocated.
2. Setup of control handlers: This must be done prior to registering
and exposing the adapters to user space to avoid a race condition.
3. Register CEC adapters: make them available to user space.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: PTR_ERR -> PTR_ERR_OR_ZERO]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds the following bitmask control:
-V4L2_CID_DV_RX_POWER_PRESENT
The RX_POWER_PRESENT bitmask is set based on the digital video timings
signal mode. This also removes 1/1 warnings for v4l2-compliance test on
vivid instance with HDMI input.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds the following bitmask controls:
-V4L2_CID_DV_TX_EDID_PRESENT
-V4L2_CID_DV_TX_HOTPLUG
-V4L2_CID_DV_TX_RXSENSE
The bitmasks are all set based on the custom vivid DISPLAY_PRESENT
control. This also removes 2/2 v4l2-compliance warnings for vivid
output device.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This will be used for HDMI-specific controls such as hotplug detection
and power present.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a custom control for selecting the presence of a display connected
to the active output. This control is part of an effort to implement
proper HDMI (dis)connect behavior for vivid.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make the following properties per-input:
-Standard Signal Mode
-Standard
These properties need to be per-input in order to implement proper HDMI
(dis)connect-behavior, where the signal mode will be used to signify
whether or not there is an inpute device connected.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make the following properties per-input
-DV Timings Signal Mode
-DV Timings
These properties need to be per-input in order to implement proper
HDMI (dis)connect-behavior, where the signal mode will be used to
signify whether or not there is an input device connected.
Signed-off-by: Johan Korsnes <johan.korsnes@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
AST2500 silicon revision A1 and A2 have a silicon bug which causes
extremly long capturing time on specific resolutions (1680 width).
To fix the bug, this commit adjusts the capturing window register
setting to 1728 if detected width is 1680. The compression window
register setting will be kept as the original width so output
result will be the same.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add comments at vimc_streamer_s_stream and vimc_streamer_thread, making
the vimc-stream totally documented.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
[hverkuil-cisco@xs4all.nl: fix typo: in a fixed framerate -> at a fixed framerate]
[hverkuil-cisco@xs4all.nl: fix typo: stops the thread -> stop the thread]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use V4L2_FRACT_COMPARE to check whether two v4l2_fract structs are equal.
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If COMPILE_TEST is y and SONY_LAPTOP is m,
building fails as below:
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 6159e12e11 ("media: meye: allow building it with COMPILE_TEST on non-x86")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The tpf_min (1/100) and tpf_max (100/1) are used as the lowest and the
highest allowable value for the desired frame period in
vivid_vid_cap_s_parm().
But the comparison between these values is unnecessary because the compared
value is already chosen from webcam_intervals[] (from 1/60 to 1/1).
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We were getting the codec interface through a proxy function that does
not bring anything compared to just accessing the interface definition
directly, so just do that. Also make the decoder interfaces const.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The interface used to communicate with the firmware casts pointers
into unsigned longs and back again in order to store private
references, all of this for pointers that remain purely in the kernel.
Replace these unsigned longs with void pointers to make the code a bit
sturdier and easier to follow.
Also simplify some interfaces by removing arguments that could be
infered from others.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Remove redundant Makefile rules (vimc_capture-objs, ...).
Stop exposing vimc-{common, streamer} as modules, since there's no use
case where they would be individually added/removed from Vimc. As
consequence, remove MODULE_ macros from vimc-{common, streamer}.
`-objs` is fitted for building host programs, change to `-y`, more
straightforward for device drivers.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Suggested-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix typo on "tranforming". Add a line break so it keeps under 80 columns.
Fix typo on "[it] need".
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the beginning the second clock ('special', 'sclk') was optional and
it is not available on some variants of Exynos SoCs (i.e. Exynos5420 with
v7 of MFC hardware).
However commit 1bce6fb3ed ("[media] s5p-mfc: Rework clock handling")
made handling of all specified clocks mandatory. This patch restores
original behavior of the driver and fixes its operation on
Exynos5420 SoCs.
Fixes: 1bce6fb3ed ("[media] s5p-mfc: Rework clock handling")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After the rework of the Gen2 file operations it's now trivial to merge
the Gen2 and Gen3 versions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function no longer serve a purpose as most tasks it performed have
been refactored, fold what remains of it into the only caller. While at
it add error checking for v4l2_ctrl_handler_setup().
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The two power helpers are now only dealing with the parallel subdevice,
merge them into a single rvin_power_parallel() helper to reduce code
duplication.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The helpers rvin_power_{on,off} deal with both VIN and the parallel
subdevice power. This makes it hard to merge the Gen2 and Gen3
open/release functions. Move the VIN power handling directly to the
open/release functions to prepare for the merge.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The format is already synced when the subdevice is bound, there is no
need to do do it every time the video device is opened.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The user should be allowed to break waiting for the lock when opening
the video device.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Runtime PM is already enabled unconditionally when the driver is probed
and disabled when it's removed. There is no point in doing it again for
Gen2 when opening and closing the video device.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver does not implement runtime resume and suspend function so
there is little point in trying to call them. This is a leftover from
the drivers soc_camera beginnings.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When building with CONFIG_VIDEO_ADV7511 and CONFIG_DRM_I2C_ADV7511
enabled as loadable modules, we see the following warning:
drivers/gpu/drm/bridge/adv7511/adv7511.ko
drivers/media/i2c/adv7511.ko
Rework so that the file is named adv7511-v4l2.c.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fixed issues that can lead to potential bugs.
Cleanup order in the driver
Taking into consideration std control creation can fail
mutex_destroy call
changing controller_formats with const specifier
some cosmetic cleanups
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This splits the Atmel ISC driver into a common base: atmel-isc-base.c
and the driver probe/dt part , atmel-sama5d2-isc.c
This is needed to keep a common ground for the sensor controller which will
be reused.
The atmel-isc will use the common symbols inside the atmel-isc-base
Future driver will also use the same symbols and redefine different aspects,
for a different version of the ISC.
This is done to avoid complete code duplication by creating a totally
different driver for the new variant of the ISC.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: folded 'atmel: atmel-sama5d2-isc: fixed checkpatch warnings' into this patch]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the newly introduced vb2_get_buffer API and avoid
accessing buffers in the queue directly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the newly introduced vb2_get_buffer API and avoid
accessing buffers in the queue directly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fixed checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the newly introduced vb2_get_buffer API and avoid
accessing buffers in the queue directly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These two control types don't really need a default value,
as they are not expected to carry any value.
However, it's slightly clearer to initialize them explicitly
instead of falling back to the switch default.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0Gj1MeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGctkH/0At3+SQPY2JJSy8
i6+TDeytFx9OggeGLPHChRfehkAlvMb/kd34QHnuEvDqUuCAMU6HZQJFKoK9mvFI
sDJVayPGDSqpm+iv8qLpMBPShiCXYVnGZeVfOdv36jUswL0k6wHV1pz4avFkDeZa
1F4pmI6O2XRkNTYQawbUaFkAngWUCBG9ECLnHJnuIY6ohShBvjI4+E2JUaht+8gO
M2h2b9ieddWmjxV3LTKgsK1v+347RljxdZTWnJ62SCDSEVZvsgSA9W2wnebVhBkJ
drSmrFLxNiM+W45mkbUFmQixRSmjv++oRR096fxAnodBxMw0TDxE1RiMQWE6rVvG
N6MC6xA=
=+B0P
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc5' into patchwork
Linux 5.2-rc5
There are some media fixes on -rc5, so merge from it at media
devel tree.
* tag 'v5.2-rc5': (210 commits)
Linux 5.2-rc5
x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback
Smack: Restore the smackfsdef mount option and add missing prefixes
ftrace: Fix NULL pointer dereference in free_ftrace_func_mapper()
module: Fix livepatch/ftrace module text permissions race
tracing/uprobe: Fix obsolete comment on trace_uprobe_create()
tracing/uprobe: Fix NULL pointer dereference in trace_uprobe_create()
tracing: Make two symbols static
tracing: avoid build warning with HAVE_NOP_MCOUNT
tracing: Fix out-of-range read in trace_stack_print()
gfs2: Fix rounding error in gfs2_iomap_page_prepare
x86/kasan: Fix boot with 5-level paging and KASAN
timekeeping: Repair ktime_get_coarse*() granularity
Revert "ALSA: hda/realtek - Improve the headset mic for Acer Aspire laptops"
mm/devm_memremap_pages: fix final page put race
PCI/P2PDMA: track pgmap references per resource, not globally
lib/genalloc: introduce chunk owners
PCI/P2PDMA: fix the gen_pool_add_virt() failure path
mm/devm_memremap_pages: introduce devm_memunmap_pages
drivers/base/devres: introduce devm_release_action()
...
The IR signal to control the Panasonic ACXA75C00600 air conditioner has
439 pulse/spaces. Increase limit to make it possible to transmit signal.
Reported-by: Takashi Kanamaru <neuralassembly@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If RC_CORE is not set, building fails:
Reported-by: Hulk Robot <hulkci@huawei.com>
Suggested-by: Sean Young <sean@mess.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There two callers of stv090x_setup_compound manage the allocation and
freeing if state there is an error condition from stv090x_setup_compound.
Currently function stv090x_setup_compound also frees the state object
too, leading to a double free in the callers of this function. Fix
this by removing the extraneous free in stv090x_setup_compound and just
leave the callers handle the allocation/free'ing.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this package is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081205.116017757@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
based on gpl code from [dibcom] which has [copyright] [c] [2004]
[amaury] [demol] [for] [dibcom] this program is free software you
can redistribute it and or modify it under the terms of the gnu
general public license as published by the free software foundation
version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081202.886876323@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 only
as published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details to obtain the license point your browser to http
www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 12 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081202.028166291@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
the original driver s license is gpl as declared with module_license
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation under version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
the original driver s license is gpl as declared with module_license
[copyright] [c] [2010] [2012] [mauro] [carvalho] [chehab] [driver]
[modified] [by] [in] [order] [to] [work] [with] [upstream] [drxk]
[driver] [and] [tons] [of] [bugs] [got] [fixed] [and] [converted]
[to] [use] [dvb] [usb] [v2] this program is free software you can
redistribute it and or modify it under the terms of the gnu general
public license as published by the free software foundation under
version 2 of the license this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204654.186977917@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 8 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204654.096873163@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 53 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.904365654@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conversion here is really trivial: just a bunch of title
markups and very few puntual changes is enough to make it to
be parsed by Sphinx and generate a nice html.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Includes support to identify and use two Hauppauge device.
- LGDT3306a ATSC/QAM demod
- si2177 tuner
- cx25840 decoder for analog tv/composite/s-video/audio
HVR-1975 dual-frontend:
- LGDT3306a ATSC/QAM demod
- si2168 DVB-C/T/T2 demod
- si2177 tuner
- cx25840 decoder for analog tv/composite/s-video/audio
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
i2c client device is the "new" method to attach to dvb modules, include
support for this functionality. Cleanup code has been added to init in
case of failure, as well as to frontend exit.
Required by Hauppauge HVR-1975
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All changes are equivalent and backwards compatible.
All current devices have been changed to use fe[0]
Code has been added to dvb init to support cleanup after failure.
Multiple frontends are required by Hauppauge HVR-1975, which is in a
later commit.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Works in ATSC and QAM as is, DVB is completely untested.
Firmware required.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Except for driver bugs (which we'll catch with a WARN_ON) this is only
to report failures of the new driver taking over the console. There's
nothing the outgoing driver can do about that, and no one ever
bothered to actually look at these return values. So remove them all.
v2: fixup unregister_framebuffer in savagefb, fbtft, ivtvfb, and neofb
drivers, reported by kbuild.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Peter Rosin <peda@axentia.se>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Mikulas Patocka <mpatocka@redhat.com>
Cc: linux-fbdev@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20190528090304.9388-19-daniel.vetter@ffwll.ch
-----BEGIN PGP SIGNATURE-----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=UXan
-----END PGP SIGNATURE-----
Merge tag 'media/v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a debug warning for satellite tuning at dvb core was producing too
much noise
- a regression at hfi_parser on Venus driver
* tag 'media/v5.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: venus: hfi_parser: fix a regression in parser
media: dvb: warning about dvb frequency limits produces too much noise
This patch fixes a spelling typo found in imx214.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MFC v6 and v7 has no register to read min scratch buffer size, so it has
to be read conditionally only if hardware supports it. This fixes following
NULL pointer exception on SoCs with MFC v6/v7:
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = f25837f9
[00000000] *pgd=bd93d835
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
Modules linked in: btmrvl_sdio btmrvl bluetooth mwifiex_sdio mwifiex ecdh_generic ecc
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
PC is at s5p_mfc_get_min_scratch_buf_size+0x30/0x3c
LR is at s5p_mfc_get_min_scratch_buf_size+0x28/0x3c
...
[<c074f998>] (s5p_mfc_get_min_scratch_buf_size) from [<c0745bc0>] (s5p_mfc_irq+0x814/0xa5c)
[<c0745bc0>] (s5p_mfc_irq) from [<c019a218>] (__handle_irq_event_percpu+0x64/0x3f8)
[<c019a218>] (__handle_irq_event_percpu) from [<c019a5d8>] (handle_irq_event_percpu+0x2c/0x7c)
[<c019a5d8>] (handle_irq_event_percpu) from [<c019a660>] (handle_irq_event+0x38/0x5c)
[<c019a660>] (handle_irq_event) from [<c019ebc4>] (handle_fasteoi_irq+0xc4/0x180)
[<c019ebc4>] (handle_fasteoi_irq) from [<c0199270>] (generic_handle_irq+0x24/0x34)
[<c0199270>] (generic_handle_irq) from [<c0199888>] (__handle_domain_irq+0x7c/0xec)
[<c0199888>] (__handle_domain_irq) from [<c04ac298>] (gic_handle_irq+0x58/0x9c)
[<c04ac298>] (gic_handle_irq) from [<c0101ab0>] (__irq_svc+0x70/0xb0)
Exception stack(0xe73ddc60 to 0xe73ddca8)
...
[<c0101ab0>] (__irq_svc) from [<c01967d8>] (console_unlock+0x5a8/0x6a8)
[<c01967d8>] (console_unlock) from [<c01981d0>] (vprintk_emit+0x118/0x2d8)
[<c01981d0>] (vprintk_emit) from [<c01983b0>] (vprintk_default+0x20/0x28)
[<c01983b0>] (vprintk_default) from [<c01989b4>] (printk+0x30/0x54)
[<c01989b4>] (printk) from [<c07500b8>] (s5p_mfc_init_decode_v6+0x1d4/0x284)
[<c07500b8>] (s5p_mfc_init_decode_v6) from [<c07230d0>] (vb2_start_streaming+0x24/0x150)
[<c07230d0>] (vb2_start_streaming) from [<c0724e4c>] (vb2_core_streamon+0x11c/0x15c)
[<c0724e4c>] (vb2_core_streamon) from [<c07478b8>] (vidioc_streamon+0x64/0xa0)
[<c07478b8>] (vidioc_streamon) from [<c0709640>] (__video_do_ioctl+0x28c/0x45c)
[<c0709640>] (__video_do_ioctl) from [<c0709bc8>] (video_usercopy+0x260/0x8a4)
[<c0709bc8>] (video_usercopy) from [<c02b3820>] (do_vfs_ioctl+0xb0/0x9fc)
[<c02b3820>] (do_vfs_ioctl) from [<c02b41a0>] (ksys_ioctl+0x34/0x58)
[<c02b41a0>] (ksys_ioctl) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xe73ddfa8 to 0xe73ddff0)
...
---[ end trace 376cf5ba6e0bee93 ]---
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If vpif_probe() fails on v4l2_device_register() and vpif_probe_complete(),
then memory allocated at initialize_vpif() for global vpif_obj.dev[i]
become unreleased.
The patch adds deallocation of vpif_obj.dev[i] on the error path.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When building with CONFIG_VIDEO_CODA and CONFIG_CODA_FS enabled as
loadable modules, we see the following warning:
fs/coda/coda.ko
drivers/media/platform/coda/coda.ko
Rework so media/platform/coda is named coda-vpu. Leaving CODA_FS as is
since that's a well known module.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CONFIG_DRM_I2C_ADV7511 and CONFIG_VIDEO_ADV7511 bind to the same
platform device, so whichever driver gets loaded first will be used on
the device. So they shouldn't be enabled at the same time.
Rework so that VIDEO_ADV7511 and VIDEO_COBALT depends on
DRM_I2C_ADV7511=n or COMPILE_TEST.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
New Gen3 R-Car platforms incorporate the FDP1 with an updated version
register. No code change is required to support these targets, but they
will currently report an error stating that the device can not be
identified.
Update the driver to match against the new device types.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We have a dedicated pointer for that, so use it. Much easier to read and
less computation involved.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We need to check whether this work we are canceling actually is
initialized.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+2e1ef9188251d9cc7944@syzkaller.appspotmail.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
uvcvideo creates a debugfs directory based on the device bus number and
device number. If a device contains more than one uvc function, the
creation of the second and following debugfs directories will fail and
print an info message like this:
"uvcvideo: Unable to create debugfs 3-2 directory."
This patch includes the uvc streaming interface number in the debugfs
directory name, to make sure it is unique. The directory name format is
changed from "<busnum>-<devnum>" to "<busnum>-<devnum>-<intfnum>"
Signed-off-by: Torleiv Sundre <torleiv@huddly.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlz8fAYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1asH/3ySguxqtqL1MCBa
4/SZ37PHeWKMerfX6ZyJdgEqK3B+PWlmuLiOMNK5h2bPLzeQQQAmHU/mfKmpXqgB
dHwUbG9yNnyUtTfsfRqAnCA6vpuw9Yb1oIzTCVQrgJLSWD0j7scBBvmzYqguOkto
ThwigLUq3AILr8EfR4rh+GM+5Dn9OTEFAxwil9fPHQo7QoczwZxpURhScT6Co9TB
DqLA3fvXbBvLs/CZy/S5vKM9hKzC+p39ApFTURvFPrelUVnythAM0dPDJg3pIn5u
g+/+gDxDFa+7ANxvxO2ng1sJPDqJMeY/xmjJYlYyLpA33B7zLNk2vDHhAP06VTtr
XCMhQ9s=
=cb80
-----END PGP SIGNATURE-----
Merge tag 'v5.2-rc4' into media/master
There are some conflicts due to SPDX changes. We also have more
patches being merged via media tree touching them.
So, let's merge back from upstream and address those.
Linux 5.2-rc4
* tag 'v5.2-rc4': (767 commits)
Linux 5.2-rc4
MAINTAINERS: Karthikeyan Ramasubramanian is MIA
i2c: xiic: Add max_read_len quirk
lockref: Limit number of cmpxchg loop retries
uaccess: add noop untagged_addr definition
x86/insn-eval: Fix use-after-free access to LDT entry
kbuild: use more portable 'command -v' for cc-cross-prefix
s390/unwind: correct stack switching during unwind
block, bfq: add weight symlink to the bfq.weight cgroup parameter
cgroup: let a symlink too be created with a cftype file
drm/nouveau/secboot/gp10[2467]: support newer FW to fix SEC2 failures on some boards
drm/nouveau/secboot: enable loading of versioned LS PMU/SEC2 ACR msgqueue FW
drm/nouveau/secboot: split out FW version-specific LS function pointers
drm/nouveau/secboot: pass max supported FW version to LS load funcs
drm/nouveau/core: support versioned firmware loading
drm/nouveau/core: pass subdev into nvkm_firmware_get, rather than device
block: free sched's request pool in blk_cleanup_queue
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
...
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Correctly handle stopping and restarting the encoder, keeping
track of the stop and drain states.
In addition it adds correct handling of corner cases, allowing
v4l2-compliance to pass.
Unfortunately, the code is getting to be quite complicated, so
we need to work on better codec support in v4l2-mem2mem.c to
simplify drivers.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return an error when attempting to subscribe to those events
for a stateless codec.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After a resolution change is detected, q_data->sizeimage is updated
to the new format, but buf_prepare is still draining buffers that
need to use the old pre-resolution-change value. So store the sizeimage
value in q_data->vb2_sizeimage in queue_setup and use that in
buf_prepare.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set V4L2_BUF_FLAG_P/KEYFRAME after decoding a frame.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stateful encoder requires the presence of this control.
Since a single buffer is sufficient for vicodec, we just
set this control to 1.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Setting the encoder output format to e.g. 1920x1080 will set the
crop rectangle to 1920x1088, the coded resolution to 1920x1088 and
the capture coded resolution and sizeimage to 1920x1088 as well.
Note that this might change, since the encoder spec is still in
flux with respect to how this should behave.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The initial sizeimage value was wrong for the stateless decoder.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rather than returning width/height values of 0, just default to
a format. Formats in V4L2 are always supposed to be valid, there
is no concept of an invalid format.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_ctrl_request_complete can sleep, so can't be called while
a spinlock is held.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The IR protocol can now only be set via the rc protocols sysfs file rather
than via module parameters or a custom procfs file. So, it is no longer
necessary to periodically check for protocol changes.
The IR_RCMM protocol does not decode the Philips RC-MM protocol (12, 24 or
32 bit variants) or any protocol rc-core can encode, so this is marked
RC_PROTO_UNKNOWN.
Tested on Technotrend/Hauppauge WinTV Nexus-S rev2.1, which comes
with a small black hauppauge remote.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move common code into a new function.
This provides the needed functionality to use dvb_module_probe() instead
of dvb_attach()!
[mchehab+samsung@kernel.org: fix an out of order error return code]
Signed-off-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Refactor out the common parts of stv6110x_probe() and stv6110x_attach()
into separate functions.
This provides the needed functionality to use dvb_module_probe() instead
of dvb_attach()!
Signed-off-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
CAP_M2M_MPLANE means the device supports _MPLANE formats for both
capture and output. Adjust the check to avoid EINVAL errors on
such devices.
Reported-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
The class_ptr will be NULL if pvr2_sysfs_class_create() fails
in pvr_init(), when call pvr2_sysfs_class_destroy(), it will
lead to null-ptr-deref, fix it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since locking is handled by regmap, the spin_lock_irqsave() in the
meson_ao_cec_g12a_read/write() regmap callbacks is not needed.
Fixes: b7778c4668 ("media: platform: meson: Add Amlogic Meson G12A AO CEC Controller driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of watchdog timeout detected while doing mode detection,
it's better triggering video engine hardware reset immediately so
this commit fixes code for the case. Other than the case, it will
trigger video engine hardware reset after RESOLUTION_CHANGE_DELAY.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are cases that interrupt bits are cleared by a 500ms delayed
work which causes unnecessary irq calls. Also, the current
interrupt handler returns IRQ_HANDLED always but it should return
IRQ_NONE if there is any unhandled interrupt. So this commit
refines the interrupt handling logic to fix these issues.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
VE_INTERRUPT_CAPTURE_COMPLETE and VE_INTERRUPT_COMP_COMPLETE are
not set at the same time but the current interrupt handling
mechanism of this driver doesn't clear the interrupt flag until
both two are set, and this behavior causes unnecessary interrupt
handler calls. In fact, this driver provides JPEG format only so
taking care of the VE_INTERRUPT_COMP_COMPLETE is enough for getting
compressed image frame so this commit gets rid of the
VE_INTERRUPT_CAPTURE_COMPLETE checking logic to simplify the logic.
Handling of VE_INTERRUPT_CAPTURE_COMPLETE could be added back later
when it's actually needed.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver prints out too much log messages when a
mode change happens, video turned off by screen saver and etc.
Actually, all cases are reported to user space properly. Also,
these are not critical errors but recoverable things, so this
commit changes the log level of some noisy printing outs.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Video Engine has a dedicated interrupt line so this driver doesn't
need to use IRQF_SHARED flag so remove it. Also, it'd be good for
following what Thomas recommended in the IRQF_ONESHOT support
patch like below:
"Note that for now IRQF_ONESHOT cannot be used with IRQF_SHARED to
avoid complex accounting mechanisms."
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Differently from other Aspeed drivers, this driver calls clock
control APIs in interrupt context. Since ECLK is coupled with a
reset bit in clk-aspeed module, aspeed_clk_enable will make 10ms of
busy waiting delay for triggering the reset and it will eventually
disturb other drivers' interrupt handling. To fix this issue, this
commit changes this driver's irq to threaded irq so that the delay
can be happened in a thread context.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver calls clk_prepare and clk_unprepare from
interrupt context too but these should be called from sleepable
context only. To fix this issue, this commit splits out
clk_enable/disable and clk_prepare/unprepare, and it places
clk_prepare/unprepare calls into the module probe/remove function.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch shouldn't have been included in the pull request as it adds
a non-standard raw mode that is for debugging only. So revert
commit ead14a7075.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The assigment of FB_VMODE_NONINTERLACE to var->vmode should be a
bit-wise or of FB_VMODE_NONINTERLACE instead of an assignment,
otherwise the previous clearing of the FB_VMODE_MASK bits of
var->vmode makes no sense and is redundant.
Addresses-Coverity: ("Unused value")
Fixes: ad4e02d508 ("[media] vivid: add a simple framebuffer device for overlay testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MT8183 will use a multi-planar format backed by a single buffer. Adapt
the existing code to be able to handle such frames instead of assuming
each frame is backed by two buffers.
Co-developed-by: Alexandre Courbot <acourbot@chromium.org>
[acourbot: refactor, cleanup and split]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Formats are read-only internal memory structures, so make them const.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Replace the GPLv2 boilerplate with the corresponding SPDX reference.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Change the way subdevices check if the stream is running. Verify the stream
pointer instead of src_frame. This makes easier to get rid of the void* and
u8* that points to frames in the subdevices structs.
Remove checks that s_stream does on subdevices. They are redundant since
the Media Controller Framework doesn't allow two streaming on the same
media pipeline at the same time.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you may redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190116.162794791@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 30 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081036.435762997@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
distributable under the terms of the gnu general public license
version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531081035.495262081@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 this program is distributed
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more
details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.889824453@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin st fifth floor boston ma 02110
1301 usa the full gnu general public license is included in this
distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 2 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000434.706787045@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
