When an event (such as an interrupt) is injected, and the stack is
shadowed (and therefore write protected), the guest will exit. The
current code will see that the stack is shadowed and emulate a few
instructions, each time postponing the injection. Eventually the
injection may succeed, but at that time the guest may be unwilling
to accept the interrupt (for example, the TPR may have changed).
This occurs every once in a while during a Windows 2008 boot.
Fix by unshadowing the fault address if the fault was due to an event
injection.
Signed-off-by: Avi Kivity <avi@qumranet.com>
There is no guarantee that the old TSS descriptor in the GDT contains
the proper base address. This is the case for Windows installation's
reboot-via-triplefault.
Use guest registers instead. Also translate the address properly.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The segment base is always a linear address, so translate before
accessing guest memory.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If NPT is enabled after loading both KVM modules on AMD and it should be
disabled, both KVM modules must be reloaded. If only the architecture module is
reloaded the behavior is undefined. With this patch it is possible to disable
NPT only by reloading the kvm_amd module.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The direct mapped shadow code (used for real mode and two dimensional paging)
sets upper-level ptes using direct assignment rather than calling
set_shadow_pte(). A nonpae host will split this into two writes, which opens
up a race if another vcpu accesses the same memory area.
Fix by calling set_shadow_pte() instead of assigning directly.
Noticed by Izik Eidus.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the guest issues a clflush in a mmio address, the instruction
can trap into the hypervisor. Currently, we do not decode clflush
properly, causing the guest to hang. This patch fixes this emulating
clflush (opcode 0f ae).
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Harden kvm_mmu_zap_page() against invalid root pages that
had been shadowed from memslots that are gone.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Flush the shadow mmu before removing regions to avoid stale entries.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch fixes issue encountered with HLT instruction
under FreeDOS's HIMEM XMS Driver.
The HLT instruction jumped directly to the done label and
skips updating the EIP value, therefore causing the guest
to spin endlessly on the same instruction.
The patch changes the instruction so that it writes back
the updated EIP value.
Signed-off-by: Mohammed Gamal <m.gamal005@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Fix a potention issue caused by kvm_mmu_slot_remove_write_access(). The
old behavior don't sync EPT TLB with modified EPT entry, which result
in inconsistent content of EPT TLB and EPT table.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
kvm_mmu_zap_page() needs slots lock held (rmap_remove->gfn_to_memslot,
for example).
Since kvm_lock spinlock is held in mmu_shrink(), do a non-blocking
down_read_trylock().
Untested.
Signed-off-by: Avi Kivity <avi@qumranet.com>
On suspend the svm_hardware_disable function is called which frees all svm_data
variables. On resume they are not re-allocated. This patch removes the
deallocation of svm_data from the hardware_disable function to the
hardware_unsetup function which is not called on suspend.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
There is no need to grab slots_lock if the vapic_page will not
be touched.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Older linux guests (in this case, 2.6.9) can attempt to
access the performance counter MSRs without a fixup section, and injecting
a GPF kills the guest. Work around by allowing the guest to write those MSRs.
Tested by me on RHEL-4 i386 and x86_64 guests, as well as F-9 guests.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The function ept_update_paging_mode_cr0() write to
CPU_BASED_VM_EXEC_CONTROL based on vmcs_config.cpu_based_exec_ctrl. That's
wrong because the variable may not consistent with the content in the
CPU_BASE_VM_EXEC_CONTROL MSR.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Instead of prefetching all segment bases before emulation, read them at the
last moment. Since most of them are unneeded, we save some cycles on
Intel machines where this is a bit expensive.
Signed-off-by: Avi Kivity <avi@qumranet.com>
rip relative decoding is relative to the instruction pointer of the next
instruction; by moving address adjustment until after decoding is complete,
we remove the need to determine the instruction size.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If we're not gonna do anything (case in which failure is already
reported), we do not need to even bother with calculating the linear rip.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Only abort guest entry if the timer count went from 0->1, since for 1->2
or larger the bit will either be set already or a timer irq will have
been injected.
Using atomic_inc_and_test() for it also introduces an SMP barrier
to the LAPIC version (thought it was unecessary because of timer
migration, but guest can be scheduled to a different pCPU between exit
and kvm_vcpu_block(), so there is the possibility for a race).
Noticed by Avi.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables coalesced MMIO for x86 architecture.
It defines KVM_MMIO_PAGE_OFFSET and KVM_CAP_COALESCED_MMIO.
It enables the compilation of coalesced_mmio.c.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Modify member in_range() of structure kvm_io_device to pass length and the type
of the I/O (write or read).
This modification allows to use kvm_io_device with coalesced MMIO.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
SVM cannot benefit from page prefetching since guest page fault bypass
cannot by made to work there. Avoid accessing the guest page table in
this case.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Encountered in FC6 boot sequence, now that we don't force ss.rpl = 0 during
the protected mode transition. Not really necessary, but nice to have.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add support for mov r, sreg (0x8c) instruction.
[avi: drop the sreg decoding table in favor of 1:1 encoding]
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add support for jmp far (opcode 0xea) instruction.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Update c->dst.bytes in decode instruction instead of instruction
itself. It's needed because if c->dst.bytes is equal to 0, the
instruction is not emulated.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Prefixes functions that will be exported with kvm_.
We also prefixed set_segment() even if it still static
to be coherent.
signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Laurent Vivier <laurent.vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add emulation for the memory type range registers, needed by VMware esx 3.5,
and by pci device assignment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
VMX hardware can cache the contents of a vcpu's vmcs. This cache needs
to be flushed when migrating a vcpu to another cpu, or (which is the case
that interests us here) when disabling hardware virtualization on a cpu.
The current implementation of decaching iterates over the list of all vcpus,
picks the ones that are potentially cached on the cpu that is being offlined,
and flushes the cache. The problem is that it uses mutex_trylock() to gain
exclusive access to the vcpu, which fires off a (benign) warning about using
the mutex in an interrupt context.
To avoid this, and to make things generally nicer, add a new per-cpu list
of potentially cached vcus. This makes the decaching code much simpler. The
list is vmx-specific since other hardware doesn't have this issue.
[andrea: fix crash on suspend/resume]
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
KVM turns off hardware virtualization extensions during reboot, in order
to disassociate the memory used by the virtualization extensions from the
processor, and in order to have the system in a consistent state.
Unfortunately virtual machines may still be running while this goes on,
and once virtualization extensions are turned off, any virtulization
instruction will #UD on execution.
Fix by adding an exception handler to virtualization instructions; if we get
an exception during reboot, we simply spin waiting for the reset to complete.
If it's a true exception, BUG() so we can have our stack trace.
Signed-off-by: Avi Kivity <avi@qumranet.com>
The KVM MMU tries to detect when a speculative pte update is not actually
used by demand fault, by checking the accessed bit of the shadow pte. If
the shadow pte has not been accessed, we deem that page table flooded and
remove the shadow page table, allowing further pte updates to proceed
without emulation.
However, if the pte itself points at a page table and only used for write
operations, the accessed bit will never be set since all access will happen
through the emulator.
This is exactly what happens with kscand on old (2.4.x) HIGHMEM kernels.
The kernel points a kmap_atomic() pte at a page table, and then
proceeds with read-modify-write operations to look at the dirty and accessed
bits. We get a false flood trigger on the kmap ptes, which results in the
mmu spending all its time setting up and tearing down shadows.
Fix by setting the shadow accessed bit on emulated accesses.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Attached is a patch that fixes a guest crash when booting older Linux kernels.
The problem stems from the fact that we are currently emulating
MSR_K7_EVNTSEL[0-3], but not emulating MSR_K7_PERFCTR[0-3]. Because of this,
setup_k7_watchdog() in the Linux kernel receives a GPF when it attempts to
write into MSR_K7_PERFCTR, which causes an OOPs.
The patch fixes it by just "fake" emulating the appropriate MSRs, throwing
away the data in the process. This causes the NMI watchdog to not actually
work, but it's not such a big deal in a virtualized environment.
When we get a write to one of these counters, we printk_ratelimit() a warning.
I decided to print it out for all writes, even if the data is 0; it doesn't
seem to make sense to me to special case when data == 0.
Tested by myself on a RHEL-4 guest, and Joerg Roedel on a Windows XP 64-bit
guest.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The in-kernel PIT emulation ignores pending timers if operating
under mode 3, which for example Hurd uses.
This mode should output a square wave, high for (N+1)/2 counts and low
for (N-1)/2 counts. As we only care about the resulting interrupts, the
period is N, and mode 3 is the same as mode 2 with regard to
interrupts.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
To distinguish between real page faults and nested page faults they should be
traced as different events. This is implemented by this patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds the missing kvmtrace markers to the svm
module of kvm.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds some kvmtrace bits to the generic x86 code
where it is instrumented from SVM.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
With an exit handler for INTR intercepts its possible to account them using
kvmtrace.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
With an exit handler for NMI intercepts its possible to account them using
kvmtrace.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch moves the trace entry for APIC accesses from the VMX code to the
generic lapic code. This way APIC accesses from SVM will also be traced.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Noticed by sparse:
arch/x86/kvm/vmx.c:1583:6: warning: symbol 'vmx_disable_intercept_for_msr' was not declared. Should it be static?
arch/x86/kvm/x86.c:3406:5: warning: symbol 'kvm_task_switch_16' was not declared. Should it be static?
arch/x86/kvm/x86.c:3429:5: warning: symbol 'kvm_task_switch_32' was not declared. Should it be static?
arch/x86/kvm/mmu.c:1968:6: warning: symbol 'kvm_mmu_remove_one_alloc_mmu_page' was not declared. Should it be static?
arch/x86/kvm/mmu.c:2014:6: warning: symbol 'mmu_destroy_caches' was not declared. Should it be static?
arch/x86/kvm/lapic.c:862:5: warning: symbol 'kvm_lapic_get_base' was not declared. Should it be static?
arch/x86/kvm/i8254.c:94:5: warning: symbol 'pit_get_gate' was not declared. Should it be static?
arch/x86/kvm/i8254.c:196:5: warning: symbol '__pit_timer_fn' was not declared. Should it be static?
arch/x86/kvm/i8254.c:561:6: warning: symbol '__inject_pit_timer_intr' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch updates the kvm host code to use the pvclock structs.
It also makes the paravirt clock compatible with Xen.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Switching msrs can occur either synchronously as a result of calls to
the msr management functions (usually in response to the guest touching
virtualized msrs), or asynchronously when preempting a kvm thread that has
guest state loaded. If we're unlucky enough to have the two at the same
time, host msrs are corrupted and the machine goes kaput on the next syscall.
Most easily triggered by Windows Server 2008, as it does a lot of msr
switching during bootup.
Signed-off-by: Avi Kivity <avi@qumranet.com>
KVM has a heuristic to unshadow guest pagetables when userspace accesses
them, on the assumption that most guests do not allow userspace to access
pagetables directly. Unfortunately, in addition to unshadowing the pagetables,
it also oopses.
This never triggers on ordinary guests since sane OSes will clear the
pagetables before assigning them to userspace, which will trigger the flood
heuristic, unshadowing the pagetables before the first userspace access. One
particular guest, though (Xenner) will run the kernel in userspace, triggering
the oops. Since the heuristic is incorrect in this case, we can simply
remove it.
Signed-off-by: Avi Kivity <avi@qumranet.com>
kvm_mmu_pte_write() does not handle 32-bit non-PAE large page backed
guests properly. It will instantiate two 2MB sptes pointing to the same
physical 2MB page when a guest large pte update is trapped.
Instead of duplicating code to handle this, disallow directory level
updates to happen through kvm_mmu_pte_write(), so the two 2MB sptes
emulating one guest 4MB pte can be correctly created by the page fault
handling path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
rmap_next() does not work correctly after rmap_remove(), as it expects
the rmap chains not to change during iteration. Fix (for now) by restarting
iteration from the beginning.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If a timer fires after kvm_inject_pending_timer_irqs() but before
local_irq_disable() the code will enter guest mode and only inject such
timer interrupt the next time an unrelated event causes an exit.
It would be simpler if the timer->pending irq conversion could be done
with IRQ's disabled, so that the above problem cannot happen.
For now introduce a new vcpu requests bit to cancel guest entry.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A guest vcpu instance can be scheduled to a different physical CPU
between the test for KVM_REQ_MIGRATE_TIMER and local_irq_disable().
If that happens, the timer will only be migrated to the current pCPU on
the next exit, meaning that guest LAPIC timer event can be delayed until
a host interrupt is triggered.
Fix it by cancelling guest entry if any vcpu request is pending. This
has the side effect of nicely consolidating vcpu->requests checks.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Shadows for large guests can take a long time to tear down, so reschedule
occasionally to avoid softlockup warnings.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Clear CR4.VMXE in hardware_disable. There's no reason to leave it set
after doing a VMXOFF.
VMware Workstation 6.5 checks CR4.VMXE as a proxy for whether the CPU is
in VMX mode, so leaving VMXE set means we'll refuse to power on. With this
change the user can power on after unloading the kvm-intel module. I
tested on kvm-67 and kvm-69.
Signed-off-by: Eli Collins <ecollins@vmware.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Migrate the PIT timer to the physical CPU which vcpu0 is scheduled on,
similarly to what is done for the LAPIC timers, otherwise PIT interrupts
will be delayed until an unrelated event causes an exit.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The hypercall instructions on Intel and AMD are different. KVM allows the
guest to choose one or the other (the default is Intel), and if the guest
chooses incorrectly, KVM will patch it at runtime to select the correct
instruction. This allows live migration between Intel and AMD machines.
This patching occurs in the x86 emulator. The current code also executes
the hypercall. Unfortunately, the tail end of the x86 emulator code also
executes, overwriting the return value of the hypercall with the original
contents of rax (which happens to be the hypercall number).
Fix not by executing the hypercall in the emulator context; instead let the
guest reissue the patched instruction and execute the hypercall via the
normal path.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Only use the APIC pending timers count to break out of HLT emulation if
the timer vector is enabled.
Certain configurations of Windows simply mask out the vector without
disabling the timer.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Otherwise hlt emulation fails if PIT is not injecting IRQ's.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A register destination encoded with a mod=3 encoding left dst.ptr NULL.
Normally we don't trap writes to registers, but in the case of smsw, we do.
Fix by pointing dst.ptr at the destination register.
Signed-off-by: Avi Kivity <avi@qumranet.com>
nonpae guests can call rmap_write_protect twice per page (for page tables)
or four times per page (for page directories), triggering a bogus warning.
Remove the warning.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This make sure not to schedule in atomic during fx_init. I also
changed the name of fpu_init to fx_finit to avoid duplicating the name
with fpu_init that is already used in the kernel, this makes grep
simpler if nothing else.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Clear pending exceptions when setting new register values. This avoids
spurious exceptions after restoring a vcpu state or after
reset-on-triple-fault.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The in-kernel PIT emulation ignores pending timers if operating under
mode 4, which for example DragonFlyBSD uses (and Plan9 too, apparently).
Mode 4 seems to be similar to one-shot mode, other than the fact that it
starts counting after the next CLK pulse once programmed, while mode 1
starts counting immediately, so add a FIXME to enhance precision.
Fixes sourceforge bug 1952988.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The recent changes allowing memory operands with lmsw and smsw left
lmsw with writeback enabled. Since lmsw has no oridinary destination
operand, the dst pointer was not initialized, resulting in an oops.
Close the hole by disabling writeback for lmsw.
Signed-off-by: Avi Kivity <avi@qumranet.com>
[aliguory: plug leak]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently EPT level is 4 for both pae and x86_64. The patch remove the #ifdef
for alloc root_hpa and free root_hpa to support EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The function get_tdp_level() provided the number of tdp level for EPT and
NPT rather than the NPT specific macro.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Move some definitions to mmu.h in order to allow building common table
entries between EPT and non-EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Rename div64_64 to div64_u64 to make it consistent with the other divide
functions, so it clearly includes the type of the divide. Move its definition
to math64.h as currently no architecture overrides the generic implementation.
They can still override it of course, but the duplicated declarations are
avoided.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Avi Kivity <avi@qumranet.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kvm_pv_mmu_op should not take mmap_sem. All gfn_to_page() callers down
in the MMU processing will take it if necessary, so as it is it can
deadlock.
Apparently a leftover from the days before slots_lock.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
There is not selective cr0 intercept bug. The code in the comment sets the
CR0.PG bit. But KVM sets the CR4.PG bit for SVM always to implement the paged
real mode. So the 'mov %eax,%cr0' instruction does not change the CR0.PG bit.
Selective CR0 intercepts only occur when a bit is actually changed. So its the
right behavior that there is no intercept on this instruction.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
With the usage of the V_TPR field this comment is now obsolete.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch disables the intercept of CR8 writes if the TPR is not masking
interrupts. This reduces the total number CR8 intercepts to below 1 percent of
what we have without this patch using Windows 64 bit guests.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the CR8 write intercept is disabled the V_TPR field of the VMCB needs to be
synced with the TPR field in the local apic.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch exports the kvm_lapic_set_tpr() function from the lapic code to
modules. It is required in the kvm-amd module to optimize CR8 intercepts.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds syncing of the lapic.tpr field to the V_TPR field of the VMCB.
With this change we can safely remove the CR8 read intercept.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
lmsw and smsw were implemented only with a register operand. Extend them
to support a memory operand as well. Fixes Windows running some display
compatibility test on AMD hosts.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Shutdown interception clears the vmcb, leaving the asid at zero (which is
illegal. so force a new asid on vmcb initialization.
Signed-off-by: Avi Kivity <avi@qumranet.com>
There is a window open between testing of pending IRQ's
and assignment of guest_mode in __vcpu_run.
Injection of IRQ's can race with __vcpu_run as follows:
CPU0 CPU1
kvm_x86_ops->run()
vcpu->guest_mode = 0 SET_IRQ_LINE ioctl
..
kvm_x86_ops->inject_pending_irq
kvm_cpu_has_interrupt()
apic_test_and_set_irr()
kvm_vcpu_kick
if (vcpu->guest_mode)
send_ipi()
vcpu->guest_mode = 1
So move guest_mode=1 assignment before ->inject_pending_irq, and make
sure that it won't reorder after it.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
So userspace can save/restore the mpstate during migration.
[avi: export the #define constants describing the value]
[christian: add s390 stubs]
[avi: ditto for ia64]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Timers that fire between guest hlt and vcpu_block's add_wait_queue() are
ignored, possibly resulting in hangs.
Also make sure that atomic_inc and waitqueue_active tests happen in the
specified order, otherwise the following race is open:
CPU0 CPU1
if (waitqueue_active(wq))
add_wait_queue()
if (!atomic_read(pit_timer->pending))
schedule()
atomic_inc(pit_timer->pending)
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
When KVM uses NPT there is no reason to intercept task switches. This patch
removes the intercept for it in that case.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This interface allows user a space application to read the trace of kvm
related events through relayfs.
Signed-off-by: Feng (Eric) Liu <eric.e.liu@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Trace markers allow userspace to trace execution of a virtual machine
in order to monitor its performance.
Signed-off-by: Feng (Eric) Liu <eric.e.liu@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
To properly forward a MCE occured while the guest is running to the host, we
have to intercept this exception and call the host handler by hand. This is
implemented by this patch.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch aligns the host version of the CR4.MCE bit with the CR4 active in
the guest. This is necessary to get MCE exceptions when the guest is running.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The svm_set_cr4 function is indented with spaces. This patch replaces
them with tabs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch introduces a gfn_to_pfn() function and corresponding functions like
kvm_release_pfn_dirty(). Using these new functions, we can modify the x86
MMU to no longer assume that it can always get a struct page for any given gfn.
We don't want to eliminate gfn_to_page() entirely because a number of places
assume they can do gfn_to_page() and then kmap() the results. When we support
IO memory, gfn_to_page() will fail for IO pages although gfn_to_pfn() will
succeed.
This does not implement support for avoiding reference counting for reserved
RAM or for IO memory. However, it should make those things pretty straight
forward.
Since we're only introducing new common symbols, I don't think it will break
the non-x86 architectures but I haven't tested those. I've tested Intel,
AMD, NPT, and hugetlbfs with Windows and Linux guests.
[avi: fix overflow when shifting left pfns by adding casts]
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Zdenek reported a bug where a looping "dmsetup status" eventually hangs
on SMP guests.
The problem is that kvm_mmu_get_page() prepopulates the shadow MMU
before write protecting the guest page tables. By doing so, it leaves a
window open where the guest can mark a pte as present while the host has
shadow cached such pte as "notrap". Accesses to such address will fault
in the guest without the host having a chance to fix the situation.
Fix by moving the write protection before the pte prefetch.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the accessed bit is not set, the guest has never accessed this page
(at least through this spte), so there's no need to mark the page
accessed. This provides more accurate data for the eviction algortithm.
Noted by Andrea Arcangeli.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Allow the Linux memory manager to reclaim memory in the kvm shadow cache.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Unify slots_lock acquision around vcpu_run(). This is simpler and less
error-prone.
Also fix some callsites that were not grabbing the lock properly.
[avi: drop slots_lock while in guest mode to avoid holding the lock
for indefinite periods]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
MSR Bitmap controls whether the accessing of an MSR causes VM Exit.
Eliminating exits on automatically saved and restored MSRs yields a
small performance gain.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This emulates the x86 hardware task switch mechanism in software, as it is
unsupported by either vmx or svm. It allows operating systems which use it,
like freedos, to run as kvm guests.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
When mmu_set_spte() checks if a page related to spte should be release as
dirty or clean, it check if the shadow pte was writeble, but in case
rmap_write_protect() is called called it is possible for shadow ptes that were
writeble to become readonly and therefor mmu_set_spte will release the pages
as clean.
This patch fix this issue by marking the page as dirty inside
rmap_write_protect().
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If we populate a shadow pte due to a fault (and not speculatively due to a
pte write) then we can set the accessed bit on it, as we know it will be
set immediately on the next guest instruction. This saves a read-modify-write
operation.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Hypercall based pte updates are faster than faults, and also allow use
of the lazy MMU mode to batch operations.
Don't report the feature if two dimensional paging is enabled.
[avi:
- one mmu_op hypercall instead of one per op
- allow 64-bit gpa on hypercall
- don't pass host errors (-ENOMEM) to guest]
[akpm: warning fix on i386]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The patch moves the PIT model from userspace to kernel, and increases
the timer accuracy greatly.
[marcelo: make last_injected_time per-guest]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Tested-and-Acked-by: Alex Davis <alex14641@yahoo.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Most Intel hosts have a stable tsc, and playing with the offset only
reduces accuracy. By limiting tsc offset adjustment only to forward updates,
we effectively disable tsc offset adjustment on these hosts.
Signed-off-by: Avi Kivity <avi@qumranet.com>
In the current inject_page_fault path KVM only checks if there is another PF
pending and injects a DF then. But it has to check for a pending DF too to
detect a shutdown condition in the VCPU. If this is not detected the VCPU goes
to a PF -> DF -> PF loop when it should triple fault. This patch detects this
condition and handles it with an KVM_SHUTDOWN exit to userspace.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Create large pages mappings if the guest PTE's are marked as such and
the underlying memory is hugetlbfs backed. If the largepage contains
write-protected pages, a large pte is not used.
Gives a consistent 2% improvement for data copies on ram mounted
filesystem, without NPT/EPT.
Anthony measures a 4% improvement on 4-way kernbench, with NPT.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Mark zapped root pagetables as invalid and ignore such pages during lookup.
This is a problem with the cr3-target feature, where a zapped root table fools
the faulting code into creating a read-only mapping. The result is a lockup
if the instruction can't be emulated.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
In two case statements, use the ever popular 'i' instead of index:
arch/x86/kvm/x86.c:1063:7: warning: symbol 'index' shadows an earlier one
arch/x86/kvm/x86.c:1000:9: originally declared here
arch/x86/kvm/x86.c:1079:7: warning: symbol 'index' shadows an earlier one
arch/x86/kvm/x86.c:1000:9: originally declared here
Make it static.
arch/x86/kvm/x86.c:1945:24: warning: symbol 'emulate_ops' was not declared. Should it be static?
Drop the return statements.
arch/x86/kvm/x86.c:2878:2: warning: returning void-valued expression
arch/x86/kvm/x86.c:2944:2: warning: returning void-valued expression
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Fixes sparse warning as well.
arch/x86/kvm/svm.c:69:15: warning: symbol 'iopm_base' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Nesting __emulate_2op_nobyte inside__emulate_2op produces many shadowed
variable warnings on the internal variable _tmp used by both macros.
Change the outer macro to use __tmp.
Avoids a sparse warning like the following at every call site of __emulate_2op
arch/x86/kvm/x86_emulate.c:1091:3: warning: symbol '_tmp' shadows an earlier one
arch/x86/kvm/x86_emulate.c:1091:3: originally declared here
[18 more warnings suppressed]
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Replaces open-coded mask calculation in macros.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This is the host part of kvm clocksource implementation. As it does
not include clockevents, it is a fairly simple implementation. We
only have to register a per-vcpu area, and start writing to it periodically.
The area is binary compatible with xen, as we use the same shadow_info
structure.
[marcelo: fix bad_page on MSR_KVM_SYSTEM_TIME]
[avi: save full value of the msr, even if enable bit is clear]
[avi: clear previous value of time_page]
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch implements the Last Branch Record Virtualization (LBRV) feature of
the AMD Barcelona and Phenom processors into the kvm-amd module. It will only
be enabled if the guest enables last branch recording in the DEBUG_CTL MSR. So
there is no increased world switch overhead when the guest doesn't use these
MSRs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch changes the kvm-amd module to allocate the SVM MSR permission map
per VCPU instead of a global map for all VCPUs. With this we have more
flexibility allowing specific guests to access virtualized MSRs. This is
required for LBR virtualization.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Change the parameter of the init_vmcb() function in the kvm-amd module from
struct vmcb to struct vcpu_svm.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Looking at Intel Volume 3b, page 148, table 20-11 and noticed
that the field name is 'Deliver' not 'Deliever'. Attached patch changes
the define name and its user in vmx.c
Signed-off-by: Ryan Harper <ryanh@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch contains the SVM architecture dependent changes for KVM to enable
support for the Nested Paging feature of AMD Barcelona and Phenom processors.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch contains the changes to the KVM MMU necessary for support of the
Nested Paging feature in AMD Barcelona and Phenom Processors.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The load_pdptrs() function is required in the SVM module for NPT support.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The mapping function for the nonpaging case in the softmmu does basically the
same as required for Nested Paging. Make this function generic so it can be
used for both.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The generic x86 code has to know if the specific implementation uses Nested
Paging. In the generic code Nested Paging is called Two Dimensional Paging
(TDP) to avoid confusion with (future) TDP implementations of other vendors.
This patch exports the availability of TDP to the generic x86 code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
To disable the use of the Nested Paging feature even if it is available in
hardware this patch adds a module parameter. Nested Paging can be disabled by
passing npt=0 to the kvm_amd module.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Let SVM detect if the Nested Paging feature is available on the hardware.
Disable it to keep this patch series bisectable.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
By moving the SVM feature detection from the each_cpu code to the hardware
setup code it runs only once. As an additional advance the feature check is now
available earlier in the module setup process.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch makes the EFER register accessible on a 32bit KVM host. This is
necessary to boot 32 bit PAE guests under SVM.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
To allow access to the EFER register in 32bit KVM the EFER specific code has to
be exported to the x86 generic code. This patch does this in a backwards
compatible manner.
[avi: add check for EFER-less hosts]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch aligns the bits the guest can set in the EFER register with the
features in the host processor. Currently it lets EFER.NX disabled if the
processor does not support it and enables EFER.LME and EFER.LMA only for KVM on
64 bit hosts.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch give the SVM and VMX implementations the ability to add some bits
the guest can set in its EFER register.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
To allow TLB entries to be retained across VM entry and VM exit, the VMM
can now identify distinct address spaces through a new virtual-processor ID
(VPID) field of the VMCS.
[avi: drop vpid_sync_all()]
[avi: add "cc" to asm constraints]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently an mmio guest pte is encoded in the shadow pagetable as a
not-present trapping pte, with the SHADOW_IO_MARK bit set. However
nothing is ever done with this information, so maintaining it is a
useless complication.
This patch moves the check for mmio to before shadow ptes are instantiated,
so the shadow code is never invoked for ptes that reference mmio. The code
is simpler, and with future work, can be made to handle mmio concurrently.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Certain x86 instructions use bits 3:5 of the byte following the opcode as an
opcode extension, with the decode sometimes depending on bits 6:7 as well.
Add support for this in the main decoding table rather than an ad-hock
adaptation per opcode.
Signed-off-by: Avi Kivity <avi@qumranet.com>
A guest partial guest pte write will leave shadow_trap_nonpresent_pte
in spte, which generates a vmexit at the next guest access through that pte.
This patch improves this by reading the full guest pte in advance and thus
being able to update the spte and eliminate the vmexit.
This helps pae guests which use two 32-bit writes to set a single 64-bit pte.
[truncation fix by Eric]
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Feng (Eric) Liu <eric.e.liu@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
While backporting 72dc67a696, a gfn_to_page()
call was duplicated instead of moved (due to an unrelated patch not being
present in mainline). This caused a page reference leak, resulting in a
fairly massive memory leak.
Fix by removing the extraneous gfn_to_page() call.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Do not assume that a shadow mapping will always point to the same host
frame number. Fixes crash with madvise(MADV_DONTNEED).
[avi: move after first printk(), add another printk()]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The vmx hardware state restore restores the tss selector and base address, but
not its length. Usually, this does not matter since most of the tss contents
is within the default length of 0x67. However, if a process is using ioperm()
to grant itself I/O port permissions, an additional bitmap within the tss,
but outside the default length is consulted. The effect is that the process
will receive a SIGSEGV instead of transparently accessing the port.
Fix by restoring the tss length. Note that i386 had this working already.
Closes bugzilla 10246.
Signed-off-by: Avi Kivity <avi@qumranet.com>
KVM tries to run as much as possible with the guest msrs loaded instead of
host msrs, since switching msrs is very expensive. It also tries to minimize
the number of msrs switched according to the guest mode; for example,
MSR_LSTAR is needed only by long mode guests. This optimization is done by
setup_msrs().
However, we must not change which msrs are switched while we are running with
guest msr state:
- switch to guest msr state
- call setup_msrs(), removing some msrs from the list
- switch to host msr state, leaving a few guest msrs loaded
An easy way to trigger this is to kexec an x86_64 linux guest. Early during
setup, the guest will switch EFER to not include SCE. KVM will stop saving
MSR_LSTAR, and on the next msr switch it will leave the guest LSTAR loaded.
The next host syscall will end up in a random location in the kernel.
Fix by reloading the host msrs before changing the msr list.
Signed-off-by: Avi Kivity <avi@qumranet.com>
For improved concurrency, the guest walk is performed concurrently with other
vcpus. This means that we need to revalidate the guest ptes once we have
write-protected the guest page tables, at which point they can no longer be
modified.
The current code attempts to avoid this check if the shadow page table is not
new, on the assumption that if it has existed before, the guest could not have
modified the pte without the shadow lock. However the assumption is incorrect,
as the racing vcpu could have modified the pte, then instantiated the shadow
page, before our vcpu regains control:
vcpu0 vcpu1
fault
walk pte
modify pte
fault in same pagetable
instantiate shadow page
lookup shadow page
conclude it is old
instantiate spte based on stale guest pte
We could do something clever with generation counters, but a test run by
Marcelo suggests this is unnecessary and we can just do the revalidation
unconditionally. The pte will be in the processor cache and the check can
be quite fast.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the local apic initial count is zero, don't start a an hrtimer with infinite
frequency, locking up the host.
Signed-off-by: Avi Kivity <avi@qumranet.com>
the cr3 variable is now inside the vcpu->arch structure.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
alloc_apic_access_page() can sleep, while vmx_vcpu_setup is called
inside a non preemptable region. Move it after put_cpu().
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
While installing Windows XP 64 bit wants to access the DEBUGCTL and the last
branch record (LBR) MSRs. Don't allowing this in KVM causes the installation to
crash. This patch allow the access to these MSRs and fixes the issue.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch replaces the mmap_sem lock for the memory slots with a new
kvm private lock, it is needed beacuse untill now there were cases where
kvm accesses user memory while holding the mmap semaphore.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Injecting an GP when accessing this MSR lets Windows crash when running some
stress test tools in KVM. So this patch emulates access to this MSR.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
One of the use cases for the supported cpuid list is to create a "greatest
common denominator" of cpu capabilities in a server farm. As such, it is
useful to be able to get the list without creating a virtual machine first.
Since the code does not depend on the vm in any way, all that is needed is
to move it to the device ioctl handler. The capability identifier is also
changed so that binaries made against -rc1 will fail gracefully.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Whilst working on getting a VM to initialize in to IA32e mode I found
this issue. set_cr0 relies on comparing the old cr0 to the new one to
work correctly. Move the assignment below so the compare can work.
Signed-off-by: Paul Knowles <paul@transitive.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Explicitly enable the NM intercept in svm_set_cr0 if we enable TS in the guest
copy of CR0 for lazy FPU switching. This fixes guest SMP with Linux under SVM.
Without that patch Linux deadlocks or panics right after trying to boot the
other CPUs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the guest writes to cr0 and leaves the TS flag at 0 while vcpu->fpu_active
is also 0, the TS flag in the guest's cr0 gets lost. This leads to corrupt FPU
state an causes Windows Vista 64bit to crash very soon after boot. This patch
fixes this bug.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
arch/x86/kvm/x86.c: In function 'emulator_cmpxchg_emulated':
arch/x86/kvm/x86.c:1746: warning: passing argument 2 of 'vcpu->arch.mmu.gva_to_gpa' makes integer from pointer without a cast
arch/x86/kvm/x86.c:1746: warning: 'addr' is used uninitialized in this function
Is true. Local variable `addr' shadows incoming arg `addr'. Avi is on
vacation for a while, so...
Cc: Avi Kivity <avi@qumranet.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves virtio under the virtualization menu and changes virtio
devices to not claim to only be for lguest.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Migrating the apic timer in the critical section is not very nice, and is
absolutely horrible with the real-time port. Move migration to the regular
vcpu execution path, triggered by a new bitflag.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
When preparing to enter the guest, if an interrupt comes in while
preemption is disabled but interrupts are still enabled, we miss a
preemption point. Fix by explicitly checking whether we need to
reschedule.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Otherwise we re-initialize the mmu caches, which will fail since the
caches are already registered, which will cause us to deinitialize said caches.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Right now rmap_remove won't set the page as dirty if the shadow pte
pointed to this page had write access and then it became readonly.
This patches fixes that, by setting the page as dirty for spte changes from
write to readonly access.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
When executing a test program called "crashme", we found the KVM guest cannot
survive more than ten seconds, then encounterd kernel panic. The basic concept
of "crashme" is generating random assembly code and trying to execute it.
After some fixes on emulator insn validity judgment, we found it's hard to
get the current emulator handle the invalid instructions correctly, for the
#UD trap for hypercall patching caused troubles. The problem is, if the opcode
itself was OK, but combination of opcode and modrm_reg was invalid, and one
operand of the opcode was memory (SrcMem or DstMem), the emulator will fetch
the memory operand first rather than checking the validity, and may encounter
an error there. For example, ".byte 0xfe, 0x34, 0xcd" has this problem.
In the patch, we simply check that if the invalid opcode wasn't vmcall/vmmcall,
then return from emulate_instruction() and inject a #UD to guest. With the
patch, the guest had been running for more than 12 hours.
Signed-off-by: Feng (Eric) Liu <eric.e.liu@intel.com>
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If some other cpu steals mmu pages between our check and an attempt to
allocate, we can run out of mmu pages. Fix by moving the check into the
same critical section as the allocation.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Convert the synchronization of the shadow handling to a separate mmu_lock
spinlock.
Also guard fetch() by mmap_sem in read-mode to protect against alias
and memslot changes.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Since gfn_to_page() is a sleeping function, and we want to make the core mmu
spinlocked, we need to pass the page from the walker context (which can sleep)
to the shadow context (which cannot).
[marcelo: avoid recursive locking of mmap_sem]
Signed-off-by: Avi Kivity <avi@qumranet.com>
In preparation for a mmu spinlock, add kvm_read_guest_atomic()
and use it in fetch() and prefetch_page().
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Do not hold kvm->lock mutex across the entire pagefault code,
only acquire it in places where it is necessary, such as mmu
hash list, active list, rmap and parent pte handling.
Allow concurrent guest walkers by switching walk_addr() to use
mmap_sem in read-mode.
And get rid of the lockless __gfn_to_page.
[avi: move kvm_mmu_pte_write() locking inside the function]
[avi: add locking for real mode]
[avi: fix cmpxchg locking]
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This adds a mechanism for exposing the virtual apic tpr to the guest, and a
protocol for letting the guest update the tpr without causing a vmexit if
conditions allow (e.g. there is no interrupt pending with a higher priority
than the new tpr).
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add a facility to report on accesses to the local apic tpr even if the
local apic is emulated in the kernel. This is basically a hack that
allows userspace to patch Windows which tends to bang on the tpr a lot.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This can help diagnosing what the guest is trying to do. In many cases
we can get away with partial emulation of msrs.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Host side TLB flush can be merged together if multiple
spte need to be write-protected.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Moving kvm_vcpu_kick() to x86.c. Since it should be
common for all archs, put its declarations in <linux/kvm_host.h>
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Move ioapic code to common, since IA64 also needs it.
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This paves the way for multiple architecture support. Note that while
ioapic.c could potentially be shared with ia64, it is also moved.
Signed-off-by: Avi Kivity <avi@qumranet.com>
