The undocumented 'icebp' instruction (aka 'int1') works pretty much like
'int3' in the absense of in-circuit probing equipment (except,
obviously, that it raises #DB instead of raising #BP), and is used by
some validation test-suites as such.
But Andy Lutomirski noticed that his test suite acted differently in kvm
than on bare hardware.
The reason is that kvm used an inexact test for the icebp instruction:
it just assumed that an all-zero VM exit qualification value meant that
the VM exit was due to icebp.
That is not unlike the guess that do_debug() does for the actual
exception handling case, but it's purely a heuristic, not an absolute
rule. do_debug() does it because it wants to ascribe _some_ reasons to
the #DB that happened, and an empty %dr6 value means that 'icebp' is the
most likely casue and we have no better information.
But kvm can just do it right, because unlike the do_debug() case, kvm
actually sees the real reason for the #DB in the VM-exit interruption
information field.
So instead of relying on an inexact heuristic, just use the actual VM
exit information that says "it was 'icebp'".
Right now the 'icebp' instruction isn't technically documented by Intel,
but that will hopefully change. The special "privileged software
exception" information _is_ actually mentioned in the Intel SDM, even
though the cause of it isn't enumerated.
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Let's just name these according to the SDM. This should make it clearer
that the are used to enable exiting and not the feature itself.
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Extends the shadow paging code, so that 5 level shadow page
table can be constructed if VM is running in 5 level paging
mode.
Also extends the ept code, so that 5 level ept table can be
constructed if maxphysaddr of VM exceeds 48 bits. Unlike the
shadow logic, KVM should still use 4 level ept table for a VM
whose physical address width is less than 48 bits, even when
the VM is running in 5 level paging mode.
Signed-off-by: Yu Zhang <yu.c.zhang@linux.intel.com>
[Unconditionally reset the MMU context in kvm_cpuid_update.
Changing MAXPHYADDR invalidates the reserved bit bitmasks.
- Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Don't use shifts, tag them correctly as EPTP and use better matching
names (PWL vs. GAW).
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
When L2 uses vmfunc, L0 utilizes the associated vmexit to
emulate a switching of the ept pointer by reloading the
guest MMU.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Enable VMFUNC in the secondary execution controls. This simplifies the
changes necessary to expose it to nested hypervisors. VMFUNCs still
cause #UD when invoked.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Acked-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Now use bit 6 of EPTP to optionally enable A/D bits for EPTP. Another
thing to change is that, when EPT accessed and dirty bits are not in use,
VMX treats accesses to guest paging structures as data reads. When they
are in use (bit 6 of EPTP is set), they are treated as writes and the
corresponding EPT dirty bit is set. The MMU didn't know this detail,
so this patch adds it.
We also have to fix up the exit qualification. It may be wrong because
KVM sets bit 6 but the guest might not.
L1 emulates EPT A/D bits using write permissions, so in principle it may
be possible for EPT A/D bits to be used by L1 even though not available
in hardware. The problem is that guest page-table walks will be treated
as reads rather than writes, so they would not cause an EPT violation.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[Fixed typo in walk_addr_generic() comment and changed bit clear +
conditional-set pattern in handle_ept_violation() to conditional-clear]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Rename the EPT_VIOLATION_READ/WRITE/INSTR constants to
EPT_VIOLATION_ACC_READ/WRITE/INSTR to more clearly indicate that these
signify the type of the memory access as opposed to the permissions
granted by the PTE.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change implements lockless access tracking for Intel CPUs without EPT
A bits. This is achieved by marking the PTEs as not-present (but not
completely clearing them) when clear_flush_young() is called after marking
the pages as accessed. When an EPT Violation is generated as a result of
the VM accessing those pages, the PTEs are restored to their original values.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MMIO SPTEs currently set both bits 62 and 63 to distinguish them as special
PTEs. However, bit 63 is used as the SVE bit in Intel EPT PTEs. The SVE bit
is ignored for misconfigured PTEs but not necessarily for not-Present PTEs.
Since MMIO SPTEs use an EPT misconfiguration, so using bit 63 for them is
acceptable. However, the upcoming fast access tracking feature adds another
type of special tracking PTE, which uses not-Present PTEs and hence should
not set bit 63.
In order to use common bits to distinguish both type of special PTEs, we
now use only bit 62 as the special bit.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This change adds some symbolic constants for VM Exit Qualifications
related to EPT Violations and updates handle_ept_violation() to use
these constants instead of hard-coded numbers.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The VMX capability MSRs advertise the set of features the KVM virtual
CPU can support. This set of features varies across different host CPUs
and KVM versions. This patch aims to addresses both sources of
differences, allowing VMs to be migrated across CPUs and KVM versions
without guest-visible changes to these MSRs. Note that cross-KVM-
version migration is only supported from this point forward.
When the VMX capability MSRs are restored, they are audited to check
that the set of features advertised are a subset of what KVM and the
CPU support.
Since the VMX capability MSRs are read-only, they do not need to be on
the default MSR save/restore lists. The userspace hypervisor can set
the values of these MSRs or read them from KVM at VCPU creation time,
and restore the same value after every save/restore.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
- Remove VMX_EPT_EXTENT_INDIVIDUAL_ADDR, since there is no such type of
EPT invalidation
- Add missing VPID types names
Signed-off-by: Jan Dakinevich <jan.dakinevich@gmail.com>
Tested-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
These are never used by the host, but they can still be reflected to
the guest.
Tested-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 8b3e34e46a.
Given the deprecation of the pcommit instruction, the relevant VMX
features and CPUID bits are not going to be rolled into the SDM. Remove
their usage from KVM.
Cc: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch exhances kvm-intel module to enable VMX TSC scaling and
collects information of TSC scaling ratio during initialization.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add the INVVPID instruction emulation.
Reviewed-by: Wincy Van <fanwenyi0529@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pass PCOMMIT CPU feature to guest to enable PCOMMIT instruction
Currently we do not catch pcommit instruction for L1 guest and
allow L1 to catch this instruction for L2 if, as required by the spec,
L1 can enumerate the PCOMMIT instruction via CPUID:
| IA32_VMX_PROCBASED_CTLS2[53] (which enumerates support for the
| 1-setting of PCOMMIT exiting) is always the same as
| CPUID.07H:EBX.PCOMMIT[bit 22]. Thus, software can set PCOMMIT exiting
| to 1 if and only if the PCOMMIT instruction is enumerated via CPUID
The spec can be found at
https://software.intel.com/sites/default/files/managed/0d/53/319433-022.pdf
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX encodes access rights differently from LAR, and the latter is
most likely what x86 people think of when they think of "access
rights".
Rename them to avoid confusion.
Cc: kvm@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow a nested hypervisor to single step its guests.
Signed-off-by: Mihai Donțu <mihai.dontu@gmail.com>
[Fix overlong line. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds PML support in VMX. A new module parameter 'enable_pml' is added
to allow user to enable/disable it manually.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Initialize the XSS exit bitmap. It is zero so there should be no XSAVES
or XRSTORS exits.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Expose the XSAVES feature to the guest if the kvm_x86_ops say it is
available.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SDM says bits 1, 4-6, 8, 13-16, and 26 have to be set.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The spec says those controls are at bit position 2 - makes 4 as value.
The impact of this mistake is effectively zero as we only use them to
ensure that these features are set at position 2 (or, previously, 1) in
MSR_IA32_VMX_{EXIT,ENTRY}_CTLS - which is and will be always true
according to the spec.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can easily emulate the HLT activity state for L1: If it decides that
L2 shall be halted on entry, just invoke the normal emulation of halt
after switching to L2. We do not depend on specific host features to
provide this, so we can expose the capability unconditionally.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we let L1 use EPT, we should probably also support the INVEPT instruction.
In our current nested EPT implementation, when L1 changes its EPT table
for L2 (i.e., EPT12), L0 modifies the shadow EPT table (EPT02), and in
the course of this modification already calls INVEPT. But if last level
of shadow page is unsync not all L1's changes to EPT12 are intercepted,
which means roots need to be synced when L1 calls INVEPT. Global INVEPT
should not be different since roots are synced by kvm_mmu_load() each
time EPTP02 changes.
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Jun Nakajima <jun.nakajima@intel.com>
Signed-off-by: Xinhao Xu <xinhao.xu@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add definitions for all the vmcs control fields/bits
required to enable vmcs-shadowing
Signed-off-by: Abel Gordon <abelg@il.ibm.com>
Reviewed-by: Orit Wasserman <owasserm@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Detect the posted interrupt feature. If it exists, then set it in vmcs_config.
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Provided the host has this feature, it's straightforward to offer it to
the guest as well. We just need to load to timer value on L2 entry if
the feature was enabled by L1 and watch out for the corresponding exit
reason.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
We will need EFER.LMA saving to provide unrestricted guest mode. All
what is missing for this is picking up EFER.LMA from VM_ENTRY_CONTROLS
on L2->L1 switches. If the host does not support EFER.LMA saving,
no change is performed, otherwise we properly emulate for L1 what the
hardware does for L0. Advertise the support, depending on the host
feature.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Only interrupt and NMI exiting are mandatory for KVM to work, thus can
be exposed to the guest unconditionally, virtual NMI exiting is
optional. So we must not advertise it unless the host supports it.
Introduce the symbolic constant PIN_BASED_ALWAYSON_WITHOUT_TRUE_MSR at
this chance.
Reviewed-by:: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Properly set those bits to 1 that the spec demands in case bit 55 of
VMX_BASIC is 0 - like in our case.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Virtual interrupt delivery avoids KVM to inject vAPIC interrupts
manually, which is fully taken care of by the hardware. This needs
some special awareness into existing interrupr injection path:
- for pending interrupt, instead of direct injection, we may need
update architecture specific indicators before resuming to guest.
- A pending interrupt, which is masked by ISR, should be also
considered in above update action, since hardware will decide
when to inject it at right time. Current has_interrupt and
get_interrupt only returns a valid vector from injection p.o.v.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
basically to benefit from apicv, we need to enable virtualized x2apic mode.
Currently, we only enable it when guest is really using x2apic.
Also, clear MSR bitmap for corresponding x2apic MSRs when guest enabled x2apic:
0x800 - 0x8ff: no read intercept for apicv register virtualization,
except APIC ID and TMCCT which need software's assistance to
get right value.
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Kevin Tian <kevin.tian@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@Intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
It's easy to confuse KVM_MEMORY_SLOTS and KVM_MEM_SLOTS_NUM. One is
the user accessible slots and the other is user + private. Make this
more obvious.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Bit24 in VMX_EPT_VPID_CAP_MASI is not used for address-specific invalidation capability
reporting, so remove it from KVM to avoid conflicts in future.
Signed-off-by: Zhang Xiantao <xiantao.zhang@intel.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Exporting KVM exit information to userspace to be consumed by perf.
Signed-off-by: Dong Hao <haodong@linux.vnet.ibm.com>
[ Dong Hao <haodong@linux.vnet.ibm.com>: rebase it on acme's git tree ]
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: kvm@vger.kernel.org
Cc: Runzhen Wang <runzhen@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1347870675-31495-2-git-send-email-haodong@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch handles PCID/INVPCID for guests.
Process-context identifiers (PCIDs) are a facility by which a logical processor
may cache information for multiple linear-address spaces so that the processor
may retain cached information when software switches to a different linear
address space. Refer to section 4.10.1 in IA32 Intel Software Developer's Manual
Volume 3A for details.
For guests with EPT, the PCID feature is enabled and INVPCID behaves as running
natively.
For guests without EPT, the PCID feature is disabled and INVPCID triggers #UD.
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instruction emulation for EOI writes can be skipped, since sane
guest simply uses MOV instead of string operations. This is a nice
improvement when guest doesn't support x2apic or hyper-V EOI
support.
a single VM bandwidth is observed with ~8% bandwidth improvement
(7.4Gbps->8Gbps), by saving ~5% cycles from EOI emulation.
Signed-off-by: Kevin Tian <kevin.tian@intel.com>
<Based on earlier work from>:
Signed-off-by: Eddie Dong <eddie.dong@intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds a bunch of tests of the validity of the vmcs12 fields,
according to what the VMX spec and our implementation allows. If fields
we cannot (or don't want to) honor are discovered, an entry failure is
emulated.
According to the spec, there are two types of entry failures: If the problem
was in vmcs12's host state or control fields, the VMLAUNCH instruction simply
fails. But a problem is found in the guest state, the behavior is more
similar to that of an exit.
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This patch implements nested_vmx_vmexit(), called when the nested L2 guest
exits and we want to run its L1 parent and let it handle this exit.
Note that this will not necessarily be called on every L2 exit. L0 may decide
to handle a particular exit on its own, without L1's involvement; In that
case, L0 will handle the exit, and resume running L2, without running L1 and
without calling nested_vmx_vmexit(). The logic for deciding whether to handle
a particular exit in L1 or in L0, i.e., whether to call nested_vmx_vmexit(),
will appear in a separate patch below.
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
VMX instructions specify success or failure by setting certain RFLAGS bits.
This patch contains common functions to do this, and they will be used in
the following patches which emulate the various VMX instructions.
Signed-off-by: Nadav Har'El <nyh@il.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
