For the P8 OCC, add the procedure to send a command to the OCC over I2C
bus. This involves writing the OCC command registers with serial
communication operations (SCOMs) interpreted by the I2C slave. For the
P9 OCC, add a procedure to use the OCC in-kernel API to send a command
to the OCC through the SBE.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The OCC is a device embedded on a POWER processor that collects and
aggregates sensor data from the processor and system. The OCC can
provide the raw sensor data as well as perform thermal and power
management on the system.
This driver provides a hwmon interface to the OCC from a service
processor (e.g. a BMC). The driver supports both POWER8 and POWER9 OCCs.
Communications with the POWER8 OCC are established over standard I2C
bus. The driver communicates with the POWER9 OCC through the FSI-based
OCC driver, which handles the lower-level communication details.
This patch lays out the structure of the OCC hwmon driver. There are two
platform drivers, one each for P8 and P9 OCCs. These are probed through
the I2C tree and the FSI-based OCC driver, respectively. The patch also
defines the first common structures and methods between the two OCC
versions.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
[groeck: Fix up SPDX license identifier]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
struct attribute::name which this local variable name is eventually
assigned to is "const char*", and so is the template parameter. We might
as well preserve the constness all the way through.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADM series of hotswap controllers support extending
the current measurement range by using a sensing resistor
value other than the typical 1 mOhm. For example, using a 0.5 mOhm
sensing resistor doubles the maximal current can be measured.
Current driver assumes a shunt resistor value of 1 mOhm in calculation,
meaning for other resistor values, hwmon will report scaled
current/power measurements. This patch parses device tree parameter
"shunt-resistor-micro-ohms", if there is one.
Signed-off-by: Kun Yi <kunyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Both datasheet and comments of store_temp_mode() tell us that temp1~4_type
is writable, so fix it.
Signed-off-by: Yao Wang <wangyao@lemote.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Fixes: 39deb6993e (" hwmon: (w83795) Simplify temperature sensor type handling")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix macros for tacometer fault reading.
This fix is relevant for three Mellanox systems MQMB7, MSN37, MSN34,
which are about to be released to the customers.
At the moment, none of them is at customers sites.
Fixes: 65afb4c8e7 ("hwmon: (mlxreg-fan) Add support for Mellanox FAN driver")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The current register (04h) has a sign bit at MSB. The comments
for this calculation also mention that it's a signed register.
However, the regval is unsigned type so result of calculation
turns out to be an incorrect value when current is negative.
This patch simply fixes this by adding a casting to s16.
Fixes: 5d389b1251 ("hwmon: (ina2xx) Make calibration register value fixed")
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In case an under-voltage happens before probing the driver wont
write the critical warning into the kernel log. So don't init
of last_throttled during probe and fix this issue.
Fixes: 74d1e00791 ("hwmon: Add support for RPi voltage sensor")
Reported-by: "Noralf Trønnes" <noralf@tronnes.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When using DT configurations, the id pointer might turn out to
be NULL. Then the driver encounters NULL pointer access:
Unable to handle kernel read from unreadable memory at vaddr 00000018
[...]
PC is at ina2xx_probe+0x114/0x200
LR is at ina2xx_probe+0x10c/0x200
[...]
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
The reason is that i2c core returns the id pointer by matching
id_table with client->name, while the client->name is actually
using the name from the first string in the DT compatible list,
not the best one. So i2c core would fail to match the id_table
if the best matched compatible string isn't the first one, and
then would return a NULL id pointer.
This probably should be fixed in i2c core. But it doesn't hurt
to make the driver robust. So this patch fixes it by using the
"chip" that's added to unify both DT and non-DT configurations.
Additionally, since id pointer could be null, so as id->name:
ina2xx 10-0047: power monitor (null) (Rshunt = 1000 uOhm)
ina2xx 10-0048: power monitor (null) (Rshunt = 10000 uOhm)
So this patch also fixes NULL name pointer, using client->name
to play safe and to align with hwmon->name.
Fixes: bd0ddd4d08 ("hwmon: (ina2xx) Add OF device ID table")
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for AMD family 17h model 30h processors for k10temp. Model
30h is functionally the same as model 01h processors (as far as k10temp
is concerned), just the PCI device IDs need to be updated.
Signed-off-by: Brian Woods <brian.woods@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Clemens Ladisch <clemens@ladisch.de>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: Jean Delvare <jdelvare@suse.com>
CC: Jia Zhang <qianyue.zj@alibaba-inc.com>
CC: <linux-hwmon@vger.kernel.org>
CC: <linux-pci@vger.kernel.org>
CC: Pu Wen <puwen@hygon.cn>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20181106200754.60722-5-brian.woods@amd.com
If gcc decides not to inline make_sensor_label():
WARNING: vmlinux.o(.text+0x4df549c): Section mismatch in reference from the function .create_device_attrs() to the function .init.text:.make_sensor_label()
The function .create_device_attrs() references
the function __init .make_sensor_label().
This is often because .create_device_attrs lacks a __init
annotation or the annotation of .make_sensor_label is wrong.
As .probe() can be called after freeing of __init memory, all __init
annotiations in the driver are bogus, and should be removed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
are logging cleanup and style fixes. There are a few smaller
bug fixes.
-corey
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ladh
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.20' of https://github.com/cminyard/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Lots of small changes to the IPMI driver. Most of the changes are
logging cleanup and style fixes. There are a few smaller bug fixes"
* tag 'for-linus-4.20' of https://github.com/cminyard/linux-ipmi: (21 commits)
ipmi: Fix timer race with module unload
ipmi:ssif: Add support for multi-part transmit messages > 2 parts
MAINTAINERS: Add file patterns for ipmi device tree bindings
ipmi: Remove platform driver overrides and use the id_table
ipmi: Free the address list on module cleanup
ipmi: Don't leave holes in the I2C address list in the ssif driver
ipmi: fix return value of ipmi_set_my_LUN
ipmi: Convert pr_xxx() to dev_xxx() in the BT code
ipmi:dmi: Ignore IPMI SMBIOS entries with a zero base address
ipmi:dmi: Use pr_fmt in the IPMI DMI code
ipmi: Change to ktime_get_ts64()
ipmi_si: fix potential integer overflow on large shift
ipmi_si_pci: fix NULL device in ipmi_si error message
ipmi: Convert printk(KERN_<level> to pr_<level>(
ipmi: Use more common logging styles
ipmi: msghandler: Add and use pr_fmt and dev_fmt, remove PFX
pci:ipmi: Move IPMI PCI class id defines to pci_ids.h
ipmi: Finally get rid of ipmi_user_t and ipmi_smi_t
ipmi:powernv: Convert ipmi_smi_t to struct ipmi_smi
hwmon:ibm: Change ipmi_user_t to struct ipmi_user *
...
A small update with a couple of new APIs that are useful for some small
sets of devices:
- Split up the single_rw flagging to map read and write separately as
some devices support bulk operations for only read or only write.
- Add a write version of the noinc API.
- Clean up the code for LOG_DEVICE a bit.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlvNvQgTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MAPB/9Ftz3U5DpfLoN/KEOQlGv6LeoryRcI
kSRXm7zlZmIrMm4xQtR59oXDSh05uPaZnbXPcIajfQhq895Y6T1+idHbd9pBmDFq
cZ+YeORg+5NSThnbJeNBa1hiMFvM8seCP2eeHEu6ZX+jWE7AmfFsW6re3e9uXg+m
DQ9tCFMnByShHFfEhWkvQiZAfPHLgN7MK6FvxAjYoUq/GeGjhCyOz1S0vNZXc4pj
P6hJHngr+6axZYQ+IXcwoGj1UdS3aZWvamL5eCV/plFYaf9uNYgnyaGxhY7/hddB
Ty3GHJOhGWZq8fjIR/ejS6M2g0c36tWq38uGHGAenyJsta1Kub/fcdzQ
=WHhl
-----END PGP SIGNATURE-----
Merge tag 'regmap-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A small update with a couple of new APIs that are useful for some
small sets of devices:
- Split up the single_rw flagging to map read and write separately as
some devices support bulk operations for only read or only write.
- Add a write version of the noinc API.
- Clean up the code for LOG_DEVICE a bit"
* tag 'regmap-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: use less #ifdef for LOG_DEVICE
regmap: Add regmap_noinc_write API
regmap: split up regmap_config.use_single_rw
regmap: fix comment for regmap.use_single_write
- Add support for trace events to hwmon core
- Add support for NCT6797D, NCT6798D, MAX31725/6, LTM4686
- Support all AMD Family 15h Model 6xh and Model 7xh processors
in k10temp driver
- Convert ina3221 driver to _info API
- Fixes, cleanups, and improvements in various drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Urmz
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add support for trace events to hwmon core
- Add support for NCT6797D, NCT6798D, MAX31725/6, LTM4686
- Support all AMD Family 15h Model 6xh and Model 7xh processors in
k10temp driver
- Convert ina3221 driver to _info API
- Fixes, cleanups, and improvements in various drivers
* tag 'hwmon-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (46 commits)
hwmon: (pmbus) Fix page count auto-detection.
hwmon: (pmbus) remove redundant 'default n' from Kconfig
hwmon: (core) Add trace events to _attr_show/store functions
hwmon: (ina3221) Use _info API to register hwmon device
hwmon: (npcm-750-pwm-fan) Change initial pwm target to 255
hwmon: (ina3221) Validate shunt resistor value from DT
hwmon: (tmp421) make const array 'names' static
hwmon: (core) Add hwmon_in_enable attribute
hwmon: (ina3221) mark PM functions as __maybe_unused
hwmon: (ina3221) Read channel input source info from DT
dt-bindings: hwmon: Add ina3221 documentation
hwmon: (ina3221) Add suspend and resume functions
hwmon: (ina3221) Fix INA3221_CONFIG_MODE macros
hwmon: (ina3221) Add INA3221_CONFIG to volatile_table
MAINTAINERS: Update PMBUS maintainer entry
hwmon: (pwm-fan) Set fan speed to 0 on suspend
hwmon: (pwm-fan) Silence error on probe deferral
hwmon: (scpi-hwmon) remove redundant continue
hwmon: (nct6775) Add support for NCT6798D
hwmon: (nct6775) Add support for NCT6797D
...
Devices with compatible="pmbus" field have zero initial page count,
and pmbus_clear_faults() being called before the page count auto-
detection does not actually clear faults because it depends on the
page count. Non-cleared faults in its turn may fail the subsequent
page count auto-detection.
This patch fixes this problem by calling pmbus_clear_fault_page()
for currently set page and calling pmbus_clear_faults() after the
page count was detected.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Bazhenov <bazhenov.dn@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'default n' is the default value for any bool or tristate Kconfig
setting so there is no need to write it explicitly.
Also since commit f467c5640c ("kconfig: only write '# CONFIG_FOO
is not set' for visible symbols") the Kconfig behavior is the same
regardless of 'default n' being present or not:
...
One side effect of (and the main motivation for) this change is making
the following two definitions behave exactly the same:
config FOO
bool
config FOO
bool
default n
With this change, neither of these will generate a
'# CONFIG_FOO is not set' line (assuming FOO isn't selected/implied).
That might make it clearer to people that a bare 'default n' is
redundant.
...
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Trace events are useful for people who collect data from the
Ftrace outputs. There're people who analyse the relationship
of cpufreq, thermal and hwmon (power/voltage/current) using
the convenient and timestamped Ftrace outputs, while unlike
cpufreq and thermal subsystems the hwmon does not have trace
events supported yet.
So this patch adds initial trace events for the hwmon core.
To call hwmon_attr_base() for aligned attr index numbers, it
also moves the function upward.
Ftrace outputs:
...: hwmon_attr_show_string: index=2, attr_name=in2_label, val=VDD_5V
...: hwmon_attr_show: index=2, attr_name=in2_input, val=5112
...: hwmon_attr_show: index=2, attr_name=curr2_input, val=440
Note that the _attr_show and _attr_store functions are tied
to the _with_info API. So a hwmon driver requiring the trace
events feature should use _with_info API to register a hwmon
device.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The hwmon core has a newer API which abstracts most of common
things in the core so as to simplify the hwmon device drivers.
This patch implements this _info API to ina3221 hwmon driver.
It also reduces the binary size:
text data bss dec hex filename
5114 1712 0 6826 1aaa drivers/hwmon/ina3221_before.o
4456 440 0 4896 1320 drivers/hwmon/ina3221.o
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Change initial PWM target to 255 to prevent overheating, for example
when BMC hangs in userspace or when userspace fan control application is
not implemented yet.
Signed-off-by: Kun Yi <kunyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The input->shunt_resistor is int type while the value from DT is
unsigned int. Meanwhile, a divide-by-zero error would happen if
the value is 0. So this patch just simply validates the value.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The const array 'names' can be made static, saves populating it on
the stack and will make it read-only.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
According to hwmon ABI, in%d_enable is a sysfs interface that
allows user space to enable and disable the input sensor. So
this patch just simply adds the attribute to the list.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When CONFIG_PM_SLEEP is disabled, we get a warning about unused
suspend/resume functions:
drivers/hwmon/ina3221.c:451:12: error: 'ina3221_resume' defined but not used [-Werror=unused-function]
static int ina3221_resume(struct device *dev)
drivers/hwmon/ina3221.c:428:12: error: 'ina3221_suspend' defined but not used [-Werror=unused-function]
static int ina3221_suspend(struct device *dev)
Picking the correct #ifdef check is hard, so let's remove
that check and instead mark the functions as __maybe_unused
to let the compiler silently drop them instead.
Fixes: 7de1ab9dac8e ("hwmon: (ina3221) Add suspend and resume functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
An ina3221 chip has three input ports. Each port is used
to measure the voltage and current of its input source.
The DT binding now has defined bindings for their input
sources, so the driver should read these information and
handle accordingly.
This patch adds a new structure of input source specific
information including input source label, shunt resistor
value and its connection status. It exposes these labels
via in[123]_label sysfs nodes upon available, and also
disables those channels where there are no input source
being connected. Meanwhile, it also adds in[123]_enable
sysfs nodes for users to get control of three channels,
and returns -ENODATA code for any sensor read according
to hwmon ABI.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Depending on the hardware design, an INA3221 chip might lose
its power during system suspend/resume. So this patch adds
a set of suspend and resume functions to cache the register
values including config register value and limit settings.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[groeck: Moved call to dev_set_drvdata()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The three INA3221_CONFIG_MODE macros are not correctly defined here.
The MODE3-1 bits are located at BIT 2-0 according to the datasheet.
So this patch just fixes them by shifting all of them with a correct
offset. However, this isn't a crital bug fix as the driver does not
use any of them at this point.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The MSB (15th bit) of INA3221_CONFIG is a self-clear reset bit.
So this register should be added to the volatile_table of the
regmap_config. Otherwise, we will see this bit is sticky in the
regcache which might accidentally reset the chip when an actual
write happens to the register.
This might not be a severe bug for the current code line since
there's no second place touching the INA3221_CONFIG except the
reset routine in the probe().
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Technically this is not required because disabling the PWM should be
enough. However, when support for atomic operations was implemented in
the PWM subsystem, only actual changes to the PWM channel are applied
during pwm_config(), which means that during after resume from suspend
the old settings won't be applied.
One possible solution is for the PWM driver to implement its own PM
operations such that settings from before suspend get applied on resume.
This has the disadvantage of completely ignoring any particular ordering
requirements that PWM user drivers might have, so it is best to leave it
up to the user drivers to apply the settings that they want at the
appropriate time.
Another way to solve this would be to read back the current state of the
PWM at the time of resume. That way, in case the configuration was lost
during suspend, applying the old settings in PWM user drivers would
actually get them applied because they differ from the current settings.
However, not all PWM drivers support reading the hardware state, and not
all hardware may support it.
The best workaround at this point seems to be to let PWM user drivers
tell the PWM subsystem that the PWM is turned off by, in addition to
disabling it, also setting the duty cycle to 0. This causes the resume
operation to apply a configuration that is different from the current
configuration, resulting in the proper state from before suspend getting
restored.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Probe deferrals aren't actual errors, so silence the error message in
case the PWM cannot yet be acquired.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The continue will not truely skip any code. hence it is safe to
remove it.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6798D is, with the exception of fan and pwm channel configuration
registers, similar to other chips of the series. One interesting
difference is the chip ID, which is now extended to 13 bit (the 12-bit
chip ID value overlaps with the chip ID of NCT6797D).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for NCT6797D. With the exception of fan/pwm configuration
registers, it is mostly compatible with NCT6795D.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For NCT6795D and NCT6796D, the DIMM temperature sources are named
"Agent[01] Dimm [01]" per datasheet. Match names in datasheets to
avoid confusion.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that everything is separated, clean up fan and pwm configuration
for NCT6796D. While doing that, take the forgotten configuration register
cre0 into account to determine if AUXFANIN2 (fan5) and AUXFANOUT2 (pwm5)
are connected.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Separate fan/pwm configuration detection for NCT6795D into separate
case statement to make the code easier to read.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While detecting the configuration for multiple chips in one go reduces
code size, it also increases code complexity. Separate chip detection
to improve code readability. As first step, separate detection for
NCT6793D.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When determining support for a given fan or pwm control, the code is
easier to read if the necessary instructions are grouped together.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use
boolean |= <expression>;
instead of
if (!boolean)
boolean = <expression>;
to assign values to boolean variables.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Declare and initialize LDN / chip specific configuration variables
earlier. This simplifies re-using the configuration variables for
multiple chips and makes the code easier to read.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Group configuration variable declarations and initialization together.
While this results in reading more registers than necessary for a given
chip, it improves code readability and simplifies extending the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using variables named after configuration registers makes it more obvious
which configuration register value is used, especially if more than one
configuration register value is used to determine a configuration detail.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use variable names from chip datasheets (crXX) instead of regval_XX
for configuration register variables. This is shorter and, together
with subsequent changes, makes the code easier to read.
No functional change.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A fan speed tolerance only makes sense if a fan target speed has been
configured in the first place. Otherwise we get odd output such as
fan1_target:0
fan1_tolerance:337500
Only display values other than 0 if a fan target speed has been configured.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Clang warns when the address of a pointer is used in a boolean context
as it will always return true.
drivers/hwmon/scmi-hwmon.c:59:24: warning: address of array
'sensor->name' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (sensor && sensor->name)
~~ ~~~~~~~~^~~~
1 warning generated.
Remove the check as it isn't doing anything currently; if validation
of the contents of the data structure was intended by the original
author (since this line has been present from the first version of
this driver), it can be added in a follow-up patch.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
PTR_ERR_OR_ZERO has implemented the same function. We prefer to use
inlined function rather than code-opened implementation.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX31725/MAX31726 are local temperature sensors with +/- 0.5 degree
Celsius accuracy and 16-bit (0.00390625 degrees Celsius) resolution.
They have a register mapping and encoding compatible with the lm75
series drivers. Address scan and extended temperature range are
not supported by this patch.
Tested on real hardware and verified temperature readings are correct.
Signed-off-by: Kun Yi <kunyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I removed the "dsw_en &&" chunk of the condition because we know that
"dsw_en" is set.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
BIOS developer guides refer to Family 15h Models 60h-6fh and Family 15h
Models 70h-7fh. So far the driver only checked for Models 60h and 70h.
However, there are now processors with other model numbers in the same
families. Example is A10-9620P family 15h model 65h. Follow the developer
guides and mask the lower 4 bit of the model number to determine the
registers to use for reading temperatures and temperature limits.
Reported-by: Guglielmo Fanini <g.fanini@gmail.com>
Cc: Guglielmo Fanini <g.fanini@gmail.com>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Checking the child node names is pointless as the DT node name can
never be NULL, so remove it.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-hwmon@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calling devm_kstrdup() on a fixed string is unnecessary, as is validating
its contents. Rearrange the code to avoid both.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for LTM4686 Ultrathin Dual 10A or
Single 20A uModule Regulator with Digital Power System Management.
Datasheet: http://www.analog.com/ltm4686
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:
kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
The documented register to retrieve the fan RPM for fan7 is found
to be unreliable at least with NCT6796D revision 3. Let's use
register 0x4ce instead. This is undocumented for NCT6796D, but
documented for NCT6797D and NCT6798D and known to be working.
Reported-by: Robert Kern <ulteq@web.de>
Cc: Robert Kern <ulteq@web.de>
Fixes: 81820059a4 ("hwmon: (nct6775) Add support for NCT6796D")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
fan7 on NCT6796D does not have a fan count register; it only has an RPM
register. Switch to using RPM registers to read the fan speed for all
chips supporting it to solve the problem for good.
Reported-by: Robert Kern <ulteq@web.de>
Cc: Robert Kern <ulteq@web.de>
Fixes: 81820059a4 ("hwmon: (nct6775) Add support for NCT6796D")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following kernel log message is reported for the nct6775 driver
on ASUS WS X299 SAGE.
nct6775: Found NCT6796D or compatible chip at 0x2e:0x290
nct6775 nct6775.656: Invalid temperature source 11 at index 0,
source register 0x100, temp register 0x73
nct6775 nct6775.656: Invalid temperature source 11 at index 2,
source register 0x300, temp register 0x77
nct6775 nct6775.656: Invalid temperature source 11 at index 3,
source register 0x800, temp register 0x79
nct6775 nct6775.656: Invalid temperature source 11 at index 4,
source register 0x900, temp register 0x7b
A recent version of the datasheet lists temperature source 11 as reserved.
However, an older version of the datasheet lists temperature sources 10
and 11 as supported virtual temperature sources. Apparently the older
version of the datasheet is correct, so list those temperature sources
as supported.
Virtual temperature sources are different than other temperature sources:
Values are not read from a temperature sensor, but written either from
BIOS or an embedded controller. As such, each virtual temperature has to
be reported. Since there is now more than one temperature source, we have
to keep virtual temperature sources in a chip-specific mask and can no
longer rely on the assumption that there is only one virtual temperature
source with a fixed index. This accounts for most of the complexity of this
patch.
Reported-by: Robert Kern <ulteq@web.de>
Cc: Robert Kern <ulteq@web.de>
Fixes: 81820059a4 ("hwmon: (nct6775) Add support for NCT6796D")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A few more fixes who have trickled in:
- MMC bus width fixup for some Allwinner platforms
- Fix for NULL deref in ti-aemif when no platform data is passed in
- Fix div by 0 in SCMI code
- Add a missing module alias in a new RPi driver
-----BEGIN PGP SIGNATURE-----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=oZbn
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few more fixes who have trickled in:
- MMC bus width fixup for some Allwinner platforms
- Fix for NULL deref in ti-aemif when no platform data is passed in
- Fix div by 0 in SCMI code
- Add a missing module alias in a new RPi driver"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
memory: ti-aemif: fix a potential NULL-pointer dereference
firmware: arm_scmi: fix divide by zero when sustained_perf_level is zero
hwmon: rpi: add module alias to raspberrypi-hwmon
arm64: allwinner: dts: h6: fix Pine H64 MMC bus width
Not all fans have a fan pulse register. This can result in reading
beyond the end of REG_FAN_PULSES and FAN_PULSE_SHIFT arrays,
and was reported by smatch as possible error.
1672 for (i = 0; i < ARRAY_SIZE(data->rpm); i++) {
^^^^^^^^^^^^^^^^^^^^^^^^
This is a 7 element array.
...
1685 data->fan_pulses[i] =
1686 (nct6775_read_value(data, data->REG_FAN_PULSES[i])
1687 >> data->FAN_PULSE_SHIFT[i]) & 0x03;
^^^^^^^^^^^^^^^^^^^^^^^^
FAN_PULSE_SHIFT is either 5 or 6
elements.
To fix the problem, we have to ensure that all REG_FAN_PULSES and
FAN_PULSE_SHIFT have the appropriate length, and that REG_FAN_PULSES
is only read if the register actually exists.
Fixes: 6c009501ff ("hwmon: (nct6775) Add support for NCT6102D/6106D")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is dead code because j can never be 1 at this point. We had
intended to just test if the bit was clear.
Fixes: bbd8decd41 ("hwmon: (nct6775) Add support for weighted fan control")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The raspberrypi-hwmon driver doesn't automatically load, although it does work
when loaded, by adding the alias it auto loads as expected when built as a
module. Tested on RPi2/RPi3 on 32 bit kernel and RPi3B+ on aarch64 with
Fedora 28 and a patched 4.18 RC kernel.
Fixes: 3c493c885cf ("hwmon: Add support for RPi voltage sensor")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
CC: Stefan Wahren <stefan.wahren@i2se.com>
CC: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
val can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
vers/hwmon/nct6775.c:2698 store_pwm_weight_temp_sel() warn: potential
spectre issue 'data->temp_src' [r]
Fix this by sanitizing val before using it to index data->temp_src
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475_read_word() function was meant to return negative error
codes on failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475_update_device() function returns error pointers. The
problem is that in show_pwmfreq() we dereference it before the check.
And then in pwm_use_point2_pwm_at_crit_show() there isn't a check at
all. I don't know if it's required, but it silences a static checker
warning and it's doesn't hurt anything to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC
-----BEGIN PGP SIGNATURE-----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=ZjwY
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Notable changes:
- A fix for a bug in our page table fragment allocator, where a page table page
could be freed and reallocated for something else while still in use, leading
to memory corruption etc. The fix reuses pt_mm in struct page (x86 only) for
a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but bring us in
to line with x86 behaviour and/or fix outright bugs. Thanks to Florian Weimer
for reporting many of these.
- A series to improve the hvc driver & related OPAL console code, which have
been seen to cause hardlockups at times. The hvc driver changes in particular
have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in use
anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM CPUs
(controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals to bring it
into line with other arches, including showing the offending VMA and dumping
the instructions around the fault.
Thanks to:
Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Alexey
Spirkov, Alistair Popple, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar,
Arnd Bergmann, Bartosz Golaszewski, Benjamin Herrenschmidt, Bharat Bhushan,
Bjoern Noetel, Boqun Feng, Breno Leitao, Bryant G. Ly, Camelia Groza,
Christophe Leroy, Christoph Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt,
Darren Stevens, Dave Young, David Gibson, Diana Craciun, Finn Thain, Florian
Weimer, Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel Stanley,
Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh Salgaonkar, Markus
Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues, Michael Hanselmann, Michael
Neuling, Michael Schmitz, Mukesh Ojha, Murilo Opsfelder Araujo, Nicholas
Piggin, Parth Y Shah, Paul Mackerras, Paul Menzel, Ram Pai, Randy Dunlap,
Rashmica Gupta, Reza Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff,
Scott Wood, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson,
Thiago Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat Rao
B, zhong jiang.
-----BEGIN PGP SIGNATURE-----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=PzRz
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- A fix for a bug in our page table fragment allocator, where a page
table page could be freed and reallocated for something else while
still in use, leading to memory corruption etc. The fix reuses
pt_mm in struct page (x86 only) for a powerpc only refcount.
- Fixes to our pkey support. Several are user-visible changes, but
bring us in to line with x86 behaviour and/or fix outright bugs.
Thanks to Florian Weimer for reporting many of these.
- A series to improve the hvc driver & related OPAL console code,
which have been seen to cause hardlockups at times. The hvc driver
changes in particular have been in linux-next for ~month.
- Increase our MAX_PHYSMEM_BITS to 128TB when SPARSEMEM_VMEMMAP=y.
- Remove Power8 DD1 and Power9 DD1 support, neither chip should be in
use anywhere other than as a paper weight.
- An optimised memcmp implementation using Power7-or-later VMX
instructions
- Support for barrier_nospec on some NXP CPUs.
- Support for flushing the count cache on context switch on some IBM
CPUs (controlled by firmware), as a Spectre v2 mitigation.
- A series to enhance the information we print on unhandled signals
to bring it into line with other arches, including showing the
offending VMA and dumping the instructions around the fault.
Thanks to: Aaro Koskinen, Akshay Adiga, Alastair D'Silva, Alexey
Kardashevskiy, Alexey Spirkov, Alistair Popple, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Bartosz Golaszewski,
Benjamin Herrenschmidt, Bharat Bhushan, Bjoern Noetel, Boqun Feng,
Breno Leitao, Bryant G. Ly, Camelia Groza, Christophe Leroy, Christoph
Hellwig, Cyril Bur, Dan Carpenter, Daniel Klamt, Darren Stevens, Dave
Young, David Gibson, Diana Craciun, Finn Thain, Florian Weimer,
Frederic Barrat, Gautham R. Shenoy, Geert Uytterhoeven, Geoff Levand,
Guenter Roeck, Gustavo Romero, Haren Myneni, Hari Bathini, Joel
Stanley, Jonathan Neuschäfer, Kees Cook, Madhavan Srinivasan, Mahesh
Salgaonkar, Markus Elfring, Mathieu Malaterre, Mauro S. M. Rodrigues,
Michael Hanselmann, Michael Neuling, Michael Schmitz, Mukesh Ojha,
Murilo Opsfelder Araujo, Nicholas Piggin, Parth Y Shah, Paul
Mackerras, Paul Menzel, Ram Pai, Randy Dunlap, Rashmica Gupta, Reza
Arbab, Rodrigo R. Galvao, Russell Currey, Sam Bobroff, Scott Wood,
Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stan Johnson, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain, Vasant Hegde, Venkat
Rao, zhong jiang"
* tag 'powerpc-4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (234 commits)
powerpc/mm/book3s/radix: Add mapping statistics
powerpc/uaccess: Enable get_user(u64, *p) on 32-bit
powerpc/mm/hash: Remove unnecessary do { } while(0) loop
powerpc/64s: move machine check SLB flushing to mm/slb.c
powerpc/powernv/idle: Fix build error
powerpc/mm/tlbflush: update the mmu_gather page size while iterating address range
powerpc/mm: remove warning about ‘type’ being set
powerpc/32: Include setup.h header file to fix warnings
powerpc: Move `path` variable inside DEBUG_PROM
powerpc/powermac: Make some functions static
powerpc/powermac: Remove variable x that's never read
cxl: remove a dead branch
powerpc/powermac: Add missing include of header pmac.h
powerpc/kexec: Use common error handling code in setup_new_fdt()
powerpc/xmon: Add address lookup for percpu symbols
powerpc/mm: remove huge_pte_offset_and_shift() prototype
powerpc/lib: Use patch_site to patch copy_32 functions once cache is enabled
powerpc/pseries: Fix endianness while restoring of r3 in MCE handler.
powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements
powerpc/fadump: handle crash memory ranges array index overflow
...
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
Change update device function to return an error pointer if needed,
and report the error to user space.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Clarified/updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
I2C SMBus sometimes returns error codes.
In the error case, measurement values are updated incorrectly.
The sensor application then generates warning log messages and SNMP traps.
To prevent this, add error handling into the update functions.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Update description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently the valid variable is of type char, but it is used as boolean.
So let's change it to bool.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Update description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The update function reads both measurement and limit values.
Those parts can be split so split them for a maintainability.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
[groeck: Clarify description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
All announced Threadripper 29xx models have a temperature offset of
27 degrees C. Simplify temperature offset table to match all 29xx
Threadripper models with a single entry. Also simplify the table to match
all 19xx Threadripper models with a single entry. This effectively drops
entries for Threadripper 1910/1920/1950 which never saw the light of day.
Cc: Michael Larabel <Michael@phoronix.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For at least the Threadripper 2950X and Threadripper 2990WX,
it's confirmed a 27 degree offset is needed.
Signed-off-by: Michael Larabel <michael@phoronix.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
OPAL firmware provides the facility for some groups of sensors to be
enabled/disabled at runtime to give the user the option of using the
system resources for collecting these sensors or not.
For example, on POWER9 systems, the On Chip Controller (OCC) gathers
various system and chip level sensors and maintains their values in
main memory.
This patch provides support for enabling/disabling the sensor groups
like power, temperature, current and voltage.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
[stewart@linux.vnet.ibm.com: Commit message]
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Use devm_iio_channel_get_all() to automatically release
channels.
Use devm_hwmon_device_register_with_groups() to
automatically unregister the device.
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
[groeck: Dropped now unnecessary platform_set_drvdata() and hwmon_dev]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some sensors support reporting minimal and lower critical power, as
well as alarms when these thresholds are reached. Add support for
these attributes to the hwmon core.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
for 4.19, please pull the following:
- Doug updates the low-level suspend/resume code for ARM SoCs to support
the latest rev B3.0 memory controllers found on newer chips with an
appropriate match structure to perform the correct entry sequencing
- Florian updates the Device Tree binding document for these memory
controllers to list all possible compatible strings that exist given
the supported memory controllers.
- Stefan adds the GET_THROTTLED firmware property value that is required
for the Rasperry Pi voltage monitoring driver and updates the
Raspberry Pi firmware driver accordingly to register such a device
using the HWMON subsystem. Finally he adds support for reporting under
voltage conditions using a specialized HWMON driver.
-----BEGIN PGP SIGNATURE-----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=mYCv
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.19/drivers' of https://github.com/Broadcom/stblinux into next/drivers
This pull request contains Broadcom ARM/ARM64/MIPS SoCs drivers changes
for 4.19, please pull the following:
- Doug updates the low-level suspend/resume code for ARM SoCs to support
the latest rev B3.0 memory controllers found on newer chips with an
appropriate match structure to perform the correct entry sequencing
- Florian updates the Device Tree binding document for these memory
controllers to list all possible compatible strings that exist given
the supported memory controllers.
- Stefan adds the GET_THROTTLED firmware property value that is required
for the Rasperry Pi voltage monitoring driver and updates the
Raspberry Pi firmware driver accordingly to register such a device
using the HWMON subsystem. Finally he adds support for reporting under
voltage conditions using a specialized HWMON driver.
* tag 'arm-soc/for-4.19/drivers' of https://github.com/Broadcom/stblinux:
firmware: raspberrypi: Remove VLA usage
firmware: raspberrypi: Register hwmon driver
hwmon: Add support for RPi voltage sensor
soc: bcm: brcmstb: Add missing DDR MEMC compatible strings
soc: bcm: brcmstb: pm: Add support for newer rev B3.0 controllers
ARM: bcm2835: Add GET_THROTTLED firmware property
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently there is no easy way to detect undervoltage conditions on a
remote Raspberry Pi. This hwmon driver retrieves the state of the
undervoltage sensor via mailbox interface. The handling based on
Noralf's modifications to the downstream firmware driver. In case of
an undervoltage condition only an entry is written to the kernel log.
CC: "Noralf Trønnes" <noralf@tronnes.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Add Nuvoton BMC NPCM750/730/715/705 Pulse Width Modulation (PWM)
and Fan tacho driver.
The Nuvoton BMC NPCM750/730/715/705 supports 8 PWM controller outputs
and 16 Fan controller inputs.
The driver provides a sysfs entries through which the user can
configure the duty-cycle value from 0(off) and 255(full speed)
and read the fan tacho rpm value.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX34451 is a 16-Channel Voltage/Current Monitor and 12-Channel
Sequencer.
Signed-off-by: Kun Yi <kunyi@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Driver obtains PWM and tachometers registers location according to the
system configuration and creates FAN/PWM hwmon objects and a cooling
device. PWM and tachometers are controlled through the on-board
programmable device, which exports its register map. This device could be
attached to any bus type, for which register mapping is supported. Single
instance is created with one PWM control, up to 12 tachometers and one
cooling device. It could be as many instances as programmable device
supports.
Currently driver will be activated from the Mellanox platform driver:
drivers/platform/x86/mlx-platform.c.
For the future ARM based systems it could be activated from the ARM
platform module.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 415eb2a1aa ("hwmon: (nct6775) Fix writing pwmX_mode") changed
the definition of the pwm_mode variable, but did not update the comment
describing it.
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit cc66b30382 ("hwmon: (nct6775) Rework temperature source and label
handling") changed a loop limit from "data->temp_label_num - 1" to "32",
as part of moving from a string array to a bit mask. This results in the
following error, reported by UBSAN.
UBSAN: Undefined behaviour in drivers/hwmon/nct6775.c:4179:27
shift exponent 32 is too large for 32-bit type 'long unsigned int'
Similar to the original loop, the limit has to be one less than the
number of bits.
Fixes: cc66b30382 ("hwmon: (nct6775) Rework temperature source and label handling")
Reported-by: Paul Menzel <pmenzel+linux-hwmon@molgen.mpg.de>
Cc: Paul Menzel <pmenzel+linux-hwmon@molgen.mpg.de>
Tested-by: Paul Menzel <pmenzel+linux-hwmon@molgen.mpg.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calling fan related SMM functions implemented by Dell BIOS firmware on Dell
XPS13 9333 freeze kernel for about 500ms. Until Dell fixes it we need to
disable fan support for Dell XPS13 9333.
Via "force" module param fan support can be enabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195751
Signed-off-by: Helge Eichelberg <kernelorg@elchenberg.name>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support live
patching again.
- Add support for patching barrier_nospec in copy_from_user() and syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu Malaterre.
- Several series optimising various parts of the 32-bit code from Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K" ("GEFanuc,C2K"),
which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by Steve, and
a fix to our powernv cpuidle driver. Then there's a series touching mm, x86 and
fs/proc/task_mmu.c, which cleans up some details around pkey support. It was
ack'ed/reviewed by Ingo & Dave and has been in next for several weeks.
Thanks to:
Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al Viro, Andrew
Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd Bergmann, Balbir Singh,
Cédric Le Goater, Christophe Leroy, Christophe Lombard, Colin Ian King, Dave
Hansen, Fabio Estevam, Finn Thain, Frederic Barrat, Gautham R. Shenoy, Haren
Myneni, Hari Bathini, Ingo Molnar, Jonathan Neuschäfer, Josh Poimboeuf,
Kamalesh Babulal, Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu
Malaterre, Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica Gupta, Ravi
Bangoria, Russell Currey, Sam Bobroff, Samuel Mendoza-Jonas, Segher
Boessenkool, Shilpasri G Bhat, Simon Guo, Souptick Joarder, Stewart Smith,
Thiago Jung Bauermann, Torsten Duwe, Vaibhav Jain, Wei Yongjun, Wolfram Sang,
Yisheng Xie, YueHaibing.
-----BEGIN PGP SIGNATURE-----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=ZlBf
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Support for split PMD page table lock on 64-bit Book3S (Power8/9).
- Add support for HAVE_RELIABLE_STACKTRACE, so we properly support
live patching again.
- Add support for patching barrier_nospec in copy_from_user() and
syscall entry.
- A couple of fixes for our data breakpoints on Book3S.
- A series from Nick optimising TLB/mm handling with the Radix MMU.
- Numerous small cleanups to squash sparse/gcc warnings from Mathieu
Malaterre.
- Several series optimising various parts of the 32-bit code from
Christophe Leroy.
- Removal of support for two old machines, "SBC834xE" and "C2K"
("GEFanuc,C2K"), which is why the diffstat has so many deletions.
And many other small improvements & fixes.
There's a few out-of-area changes. Some minor ftrace changes OK'ed by
Steve, and a fix to our powernv cpuidle driver. Then there's a series
touching mm, x86 and fs/proc/task_mmu.c, which cleans up some details
around pkey support. It was ack'ed/reviewed by Ingo & Dave and has
been in next for several weeks.
Thanks to: Akshay Adiga, Alastair D'Silva, Alexey Kardashevskiy, Al
Viro, Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Arnd
Bergmann, Balbir Singh, Cédric Le Goater, Christophe Leroy, Christophe
Lombard, Colin Ian King, Dave Hansen, Fabio Estevam, Finn Thain,
Frederic Barrat, Gautham R. Shenoy, Haren Myneni, Hari Bathini, Ingo
Molnar, Jonathan Neuschäfer, Josh Poimboeuf, Kamalesh Babulal,
Madhavan Srinivasan, Mahesh Salgaonkar, Mark Greer, Mathieu Malaterre,
Matthew Wilcox, Michael Neuling, Michal Suchanek, Naveen N. Rao,
Nicholas Piggin, Nicolai Stange, Olof Johansson, Paul Gortmaker, Paul
Mackerras, Peter Rosin, Pridhiviraj Paidipeddi, Ram Pai, Rashmica
Gupta, Ravi Bangoria, Russell Currey, Sam Bobroff, Samuel
Mendoza-Jonas, Segher Boessenkool, Shilpasri G Bhat, Simon Guo,
Souptick Joarder, Stewart Smith, Thiago Jung Bauermann, Torsten Duwe,
Vaibhav Jain, Wei Yongjun, Wolfram Sang, Yisheng Xie, YueHaibing"
* tag 'powerpc-4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (251 commits)
powerpc/64s/radix: Fix missing ptesync in flush_cache_vmap
cpuidle: powernv: Fix promotion from snooze if next state disabled
powerpc: fix build failure by disabling attribute-alias warning in pci_32
ocxl: Fix missing unlock on error in afu_ioctl_enable_p9_wait()
powerpc-opal: fix spelling mistake "Uniterrupted" -> "Uninterrupted"
powerpc: fix spelling mistake: "Usupported" -> "Unsupported"
powerpc/pkeys: Detach execute_only key on !PROT_EXEC
powerpc/powernv: copy/paste - Mask SO bit in CR
powerpc: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove core support for Marvell mv64x60 hostbridges
powerpc/boot: Remove support for Marvell mv64x60 i2c controller
powerpc/boot: Remove support for Marvell MPSC serial controller
powerpc/embedded6xx: Remove C2K board support
powerpc/lib: optimise PPC32 memcmp
powerpc/lib: optimise 32 bits __clear_user()
powerpc/time: inline arch_vtime_task_switch()
powerpc/Makefile: set -mcpu=860 flag for the 8xx
powerpc: Implement csum_ipv6_magic in assembly
powerpc/32: Optimise __csum_partial()
powerpc/lib: Adjust .balign inside string functions for PPC32
...
Use devm_* variants of kstrdup and kzalloc. Get rid of kfree cleanups.
Signed-off-by: Bastian Germann <bastiangermann@fishpost.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make the asus_atk0110 driver use hwmon_device_register_with_groups instead
of the deprecated hwmon_device_register.
Construct the expected attribute_group array from the sensor list which
contains all needed attributes.
Remove the manual sysfs file creation and deletion that are now taken care
of by the (un)register calls via the attribute_group array.
Signed-off-by: Bastian Germann <bastiangermann@fishpost.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The function get_raw_temp is local to the source and does not need to
be in global scope, so make it static.
Cleans up sparse warning:
drivers/hwmon/k10temp.c:149:14: warning: symbol 'get_raw_temp' was not
declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Updated version of the ltc2990 driver which supports all measurement
modes (current, voltage, temperature) available in the chip.
If devicetree is used, the mode must be specified with the property
"lltc,meas-mode". The format and possible values of the property are
described in the binding.
If devicetree is not used, the mode of the chip will not be configured.
Unless the chip is configured by another source, only the internal
temperature and supply voltage will be measured.
Signed-off-by: Tom Levens <tom.levens@cern.ch>
Tested-By: mike.looijmans@topic.nl
[groeck: Fixed compiler warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix incorrect conversion of negative temperatures by using
sign_extend32() instead of a home-grown conversion function.
Fixes: df92270357 ("hwmon: Add LTC2990 sensor driver")
Signed-off-by: Tom Levens <tom.levens@cern.ch>
[groeck: Updated subject and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
hwmon_device_register_with_info() registration API requires a
non-NULL parent device when chip is non-NULL.
This commit adds a check and documents this requirement.
Signed-off-by: Lucas Magasweran <lucas.magasweran@ieee.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some AMD CPUs, there is a different between the die temperature
(Tdie) and the reported temperature (Tctl). Tdie is the real measured
temperature, and Tctl is used for fan control. Lets report both for
affected CPUs.
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Stoney Ridge and Bristol Ridge (Family 15h Model 0x70)
CPUs. Registers match those of Family 15h Model 0x60.
Cc: stable@vger.kernel.org # v4.16+
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch exports the accumulated power numbers of each power
sensor maintained by OCC.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The firmware has supported for reading sensor values of size u32.
This patch adds support to use newer firmware functions which allows
to read the sensors of size u64.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The SMN (System Management Network) on Family 17h AMD CPUs is also accessed
from other drivers, specifically EDAC. Accessing it directly is racy.
On top of that, accessing the SMN through root bridge 00:00 is wrong on
multi-die CPUs and may result in reading the temperature from the wrong
die. Use available API functions to fix the problem.
For this to work, add dependency on AMD_NB. Also change the Raven Ridge
PCI device ID to point to Data Fabric Function 3, since this ID is used
by the API functions to find the CPU node.
Cc: stable@vger.kernel.org # v4.16+
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The HTC (Hardware Temperature Control) register has moved
for recent chips.
Cc: stable@vger.kernel.org # v4.16+
Tested-by: Gabriel Craciunescu <nix.or.die@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Enable k10temp for AMD Ryzen APUs w/ Vega Mobile Gfx.
Based on patch from René Rebe <rene@exactcode.de>. Dropped temperature
offsets since those are not supposed to apply for the affected CPUs.
Cc: stable@vger.kernel.org # v4.16+
Cc: René Rebe <rene@exactcode.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Ryzen 2700X has a temperature offset of 10 degrees C. If bit 19 of the
Temperature Control register is set, there is an additional offset of
49 degrees C. Take this into account as well.
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On Asrock Z370M Pro4, it was observed that EC access was disabled after
initially booting the system. As a result, the driver failed to load
with
nct6683: EC is disabled
After a suspend/resume cycle, the driver loaded correctly.
nct6683: Found NCT6683D or compatible chip at 0x2e:0xa20
nct6683 nct6683.2592: NCT6683D EC firmware version 1.0 build 07/18/16
Enable EC access after identifying the chip if disabled to fix the problem.
Warn the user that the data it reports may be unusable, similar to other
drivers for chips from Nuvoton.
Fixes: 41082d66bf ("hwmon: Driver for NCT6683D")
Reported-by: Jonathan Sims <jonathan.625266@earthlink.net>
Tested-by: Jonathan Sims <jonathan.625266@earthlink.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently the loop checks for non-zero count of sensors for each type
of sensors which is completely wrong. It also results in aborting the
registration of sensors if one or more types of sensors are completely
not supported by the platform SCMI firmware.
This patch fixes the issue by continue to loop and skiping sensor types
that are not present.
Fixes: b23688aefb ("hwmon: add support for sensors exported via ARM SCMI")
Reported-by: Jim Quinlan <james.quinlan@broadcom.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The uid and die temperature can be read out on the ADIN7 using
input mux. Map uid and die temperature sensor to channels 16
and 17.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
New centaur CPUs (Familiy == 7) also support this cpu temperature sensor.
Signed-off-by: David Wang <davidwang@zhaoxin.com>
[groeck: Dropped changelog, updated subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwmX_mode is defined in the ABI as 0=DC mode, 1=pwm mode. The chip
register bit is set to 1 for DC mode. This got mixed up, and writing
1 into pwmX_mode resulted in DC mode enabled. Fix it up by using
the ABI definition throughout the driver for consistency.
Fixes: 77eb5b3703 ("hwmon: (nct6775) Add support for pwm, pwm_mode, ... ")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Couple of fixes for build warning due to uninitialised variable
and static checker warning for passing NULL pointer to PTR_ERR.
It also contains cleanup suggested by Stephen Boyd in SCMI clock
driver using the new devm_of_clk_add_hw_provider() API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Gvhw
-----END PGP SIGNATURE-----
Merge tag 'scmi-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Pull "ARM SCMI fixes/cleanups for v4.17" from Sudeep Holla:
Couple of fixes for build warning due to uninitialised variable
and static checker warning for passing NULL pointer to PTR_ERR.
It also contains cleanup suggested by Stephen Boyd in SCMI clock
driver using the new devm_of_clk_add_hw_provider() API.
* tag 'scmi-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
Since autodetection of this chip was removed, it makes sense to add prefix
max6635 so that the device can be instantiated by its actual name.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Maxim MAX663x family are mostly compatible with LM92, but they lack any
identification register. Weakening the detect function would make it prone
to false positives, and current one doesn't detect all chips. Therefore,
the detect function for max6635 devices is removed in favor of explicit
device instatiation.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Passing NULL pointer to PTR_ERR will result in return value of 0
indicating success which is clearly not what it is intended here.
This patch returns -EINVAL instead when the sensor information is not
available.
Fixes: b23688aefb ("hwmon: add support for sensors exported via ARM SCMI")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Expose the gpiN_fault fields of mfr_status as individual debugfs
attributes. This provides a way for users to be easily notified of gpi
faults. Also provide the whole mfr_status register in debugfs.
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a struct gpio_chip and define some methods so that this device's
I/O can be accessed via /sys/class/gpio.
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6796D is mostly compatible to NCT6795D. It supports an additional
pwm control and fan speed channel.
While we are at it, update documentation for NCT6795D.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Initialize boolean flags in nct6775_check_fan_inputs() while
declaring them instead of several times throughout the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Improve fan6/pwm6 detection on NCT6795D. Add support for fan pulses
for fans 4..6 and fan min limits for fan6.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The size of some of the arrays using the number of fans is hardcoded.
Use NUM_FAN consistently throughout the driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and use devm_add_action() to handle cleanup.
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
[groeck: Dropped unnecessary dummy function and NULL check]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The previously used URLs are dead.
Sensirion provides permalinks for their product datasheets at
https://www.sensirion.com/en/about-us/links/.
Signed-off-by: Danilo Bargen <mail@dbrgn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A negative page register value means that no page needs to be
selected. This is used by status register read operations and needs
to be accepted. The failure to do so so results in missed status
and limit registers.
Fixes: da8e48ab48 ("hwmon: (pmbus) Always call _pmbus_read_byte in core driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A negative page register value means that no page needs to be
selected. This is used by status register evaluations and needs
to be accepted.
Fixes: da8e48ab48 ("hwmon: (pmbus) Always call _pmbus_read_byte in core driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ARM System Control and Management Interface(SCMI)[1] is more flexible and
easily extensible than any of the existing interfaces.
Few existing as well as future ARM platforms provide micro-controllers
to abstract various power and other system management tasks which have
similar interfaces, both in terms of the functions that are provided by
them, and in terms of how requests are communicated to them.
There are quite a few protocols like ARM SCPI, TI SCI, QCOM RPM, Nvidia Tegra
BPMP, and so on already. This specification is to standardize and avoid any
further fragmentation in the design of such interface by various vendors.
The current SCMI driver implementation is very basic and initial support.
It lacks support for notifications, asynchronous/delayed response, perf/power
statistics region and sensor register region.
Mailbox is the only form of transport supported currently in the driver.
SCMI supports interrupt based mailbox communication, where, on completion
of the processing of a message, the caller receives an interrupt as well as
polling for completion.
SCMI is designed to minimize the dependency on the mailbox/transport
hardware. So in terms of SCMI, each channel in the mailbox includes
memory area, doorbell and completion interrupt.
However the doorbell and completion interrupt is highly mailbox dependent
which was bit of controversial as part of SCMI/mailbox discussions.
Arnd and me discussed about the few aspects of SCMI and the mailbox framework:
1. Use of mailbox framework for doorbell type mailbox controller:
- Such hardware may not require any data to be sent to signal the remote
about the presence of a message. The channel will have in-built
information on how to trigger the signal to the remote.
There are few mailbox controller drivers which are purely doorbell based.
e.g.QCOM IPC, STM, Tegra, ACPI PCC,..etc
2. Supporting other mailbox controller:
- SCMI just needs a mechanism to signal the remote firmware. Such
controller may need fixed message to be sent to trigger a doorbell.
In such case we may need to get that data from DT and pass the same
to the controller. It's not covered in the current DT binding, but
can be extended as optional property in future.
However handling notifications may be interesting on such mailbox, but
again there is no way to interpret what the data field(remote message)
means, it could be a bit mask or a number or don't-care.
Arnd mentioned that he doesn't like the way the mailbox binding deals
with doorbell-type hardware, but we do have quite a few precedent drivers
already and changing the binding to add a data field would not make it any
better, but could cause other problems. So he is happy with the status quo
of SCMI implementation.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.den0056a/index.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qOck
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Pull "ARM SCMI support for v4.17" from Sudeep Holla:
ARM System Control and Management Interface(SCMI)[1] is more flexible and
easily extensible than any of the existing interfaces.
Few existing as well as future ARM platforms provide micro-controllers
to abstract various power and other system management tasks which have
similar interfaces, both in terms of the functions that are provided by
them, and in terms of how requests are communicated to them.
There are quite a few protocols like ARM SCPI, TI SCI, QCOM RPM, Nvidia Tegra
BPMP, and so on already. This specification is to standardize and avoid any
further fragmentation in the design of such interface by various vendors.
The current SCMI driver implementation is very basic and initial support.
It lacks support for notifications, asynchronous/delayed response, perf/power
statistics region and sensor register region.
Mailbox is the only form of transport supported currently in the driver.
SCMI supports interrupt based mailbox communication, where, on completion
of the processing of a message, the caller receives an interrupt as well as
polling for completion.
SCMI is designed to minimize the dependency on the mailbox/transport
hardware. So in terms of SCMI, each channel in the mailbox includes
memory area, doorbell and completion interrupt.
However the doorbell and completion interrupt is highly mailbox dependent
which was bit of controversial as part of SCMI/mailbox discussions.
Arnd and me discussed about the few aspects of SCMI and the mailbox framework:
1. Use of mailbox framework for doorbell type mailbox controller:
- Such hardware may not require any data to be sent to signal the remote
about the presence of a message. The channel will have in-built
information on how to trigger the signal to the remote.
There are few mailbox controller drivers which are purely doorbell based.
e.g.QCOM IPC, STM, Tegra, ACPI PCC,..etc
2. Supporting other mailbox controller:
- SCMI just needs a mechanism to signal the remote firmware. Such
controller may need fixed message to be sent to trigger a doorbell.
In such case we may need to get that data from DT and pass the same
to the controller. It's not covered in the current DT binding, but
can be extended as optional property in future.
However handling notifications may be interesting on such mailbox, but
again there is no way to interpret what the data field(remote message)
means, it could be a bit mask or a number or don't-care.
Arnd mentioned that he doesn't like the way the mailbox binding deals
with doorbell-type hardware, but we do have quite a few precedent drivers
already and changing the binding to add a data field would not make it any
better, but could cause other problems. So he is happy with the status quo
of SCMI implementation.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.den0056a/index.html
* tag 'scmi-updates-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
cpufreq: scmi: add support for fast frequency switching
cpufreq: add support for CPU DVFS based on SCMI message protocol
hwmon: add support for sensors exported via ARM SCMI
hwmon: (core) Add hwmon_max to hwmon_sensor_types enumeration
clk: add support for clocks provided by SCMI
firmware: arm_scmi: add device power domain support using genpd
firmware: arm_scmi: add per-protocol channels support using idr objects
firmware: arm_scmi: refactor in preparation to support per-protocol channels
firmware: arm_scmi: add option for polling based performance domain operations
firmware: arm_scmi: add support for polling based SCMI transfers
firmware: arm_scmi: probe and initialise all the supported protocols
firmware: arm_scmi: add initial support for sensor protocol
firmware: arm_scmi: add initial support for power protocol
firmware: arm_scmi: add initial support for clock protocol
firmware: arm_scmi: add initial support for performance protocol
firmware: arm_scmi: add scmi protocol bus to enumerate protocol devices
firmware: arm_scmi: add common infrastructure and support for base protocol
firmware: arm_scmi: add basic driver infrastructure for SCMI
dt-bindings: arm: add support for ARM System Control and Management Interface(SCMI) protocol
dt-bindings: mailbox: add support for mailbox client shared memory
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Management Interface
(SCMI). The supported sensor types is one of voltage, temperature,
current, and power.
The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kHhI
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix bad temperature display on Ryzen/Threadripper"
* tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Only apply temperature offset if result is positive
Pull x86 PTI and Spectre related fixes and updates from Ingo Molnar:
"Here's the latest set of Spectre and PTI related fixes and updates:
Spectre:
- Add entry code register clearing to reduce the Spectre attack
surface
- Update the Spectre microcode blacklist
- Inline the KVM Spectre helpers to get close to v4.14 performance
again.
- Fix indirect_branch_prediction_barrier()
- Fix/improve Spectre related kernel messages
- Fix array_index_nospec_mask() asm constraint
- KVM: fix two MSR handling bugs
PTI:
- Fix a paranoid entry PTI CR3 handling bug
- Fix comments
objtool:
- Fix paranoid_entry() frame pointer warning
- Annotate WARN()-related UD2 as reachable
- Various fixes
- Add Add Peter Zijlstra as objtool co-maintainer
Misc:
- Various x86 entry code self-test fixes
- Improve/simplify entry code stack frame generation and handling
after recent heavy-handed PTI and Spectre changes. (There's two
more WIP improvements expected here.)
- Type fix for cache entries
There's also some low risk non-fix changes I've included in this
branch to reduce backporting conflicts:
- rename a confusing x86_cpu field name
- de-obfuscate the naming of single-TLB flushing primitives"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
x86/entry/64: Fix CR3 restore in paranoid_exit()
x86/cpu: Change type of x86_cache_size variable to unsigned int
x86/spectre: Fix an error message
x86/cpu: Rename cpu_data.x86_mask to cpu_data.x86_stepping
selftests/x86/mpx: Fix incorrect bounds with old _sigfault
x86/mm: Rename flush_tlb_single() and flush_tlb_one() to __flush_tlb_one_[user|kernel]()
x86/speculation: Add <asm/msr-index.h> dependency
nospec: Move array_index_nospec() parameter checking into separate macro
x86/speculation: Fix up array_index_nospec_mask() asm constraint
x86/debug: Use UD2 for WARN()
x86/debug, objtool: Annotate WARN()-related UD2 as reachable
objtool: Fix segfault in ignore_unreachable_insn()
selftests/x86: Disable tests requiring 32-bit support on pure 64-bit systems
selftests/x86: Do not rely on "int $0x80" in single_step_syscall.c
selftests/x86: Do not rely on "int $0x80" in test_mremap_vdso.c
selftests/x86: Fix build bug caused by the 5lvl test which has been moved to the VM directory
selftests/x86/pkeys: Remove unused functions
selftests/x86: Clean up and document sscanf() usage
selftests/x86: Fix vDSO selftest segfault for vsyscall=none
x86/entry/64: Remove the unused 'icebp' macro
...
x86_mask is a confusing name which is hard to associate with the
processor's stepping.
Additionally, correct an indent issue in lib/cpu.c.
Signed-off-by: Jia Zhang <qianyue.zj@alibaba-inc.com>
[ Updated it to more recent kernels. ]
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1514771530-70829-1-git-send-email-qianyue.zj@alibaba-inc.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A user reports a really bad temperature on Ryzen 1950X.
k10temp-pci-00cb
Adapter: PCI adapter
temp1: +4294948.3°C (high = +70.0°C)
This will happen if the temperature reported by the chip is lower than
the offset temperature. This has been seen in the field if "Sense MI Skew"
and/or "Sense MI Offset" BIOS parameters were set to unexpected values.
Let's report a temperature of 0 degrees C in that case.
Fixes: 1b50b77635 ("hwmon: (k10temp) Add support for temperature offsets")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calling fan related SMM functions implemented by Dell BIOS firmware on Dell
Vostro 3360 freeze kernel for about 500ms.
Unfortunately, it is unlikely for Dell to fix this since the machine
is pretty old, so this commit just disables fan support to make the
system usable again.
Via "force" module param fan support can be enabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195751
Link: http://lkml.iu.edu/hypermail/linux/kernel/1711.2/06083.html
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calling fan related SMM functions implemented by Dell BIOS firmware on Dell
Inspiron 7720 freeze kernel for about 500ms. Until Dell fixes it we need to
disable fan support for Dell Inspiron 7720 as it makes system unusable.
Via "force" module param fan support can be enabled.
Reported-by: vova7890@mail.ru
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195751
Cc: stable@vger.kernel.org # v4.0+, will need backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some Dell machines are broken and some functionality is disabled. Show
warning into dmesg about this fact and allow user via "force" module param
to override brokenness and enable broken functionality.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Initialize data->config_lock mutex before it is used by the driver code.
This fixes following warning on Odroid XU3 boards:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc7-next-20180115-00001-gb75575dee3f2 #107
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0111504>] (unwind_backtrace) from [<c010dbec>] (show_stack+0x10/0x14)
[<c010dbec>] (show_stack) from [<c09b3f74>] (dump_stack+0x90/0xc8)
[<c09b3f74>] (dump_stack) from [<c0179528>] (register_lock_class+0x1c0/0x59c)
[<c0179528>] (register_lock_class) from [<c017bd1c>] (__lock_acquire+0x78/0x1850)
[<c017bd1c>] (__lock_acquire) from [<c017de30>] (lock_acquire+0xc8/0x2b8)
[<c017de30>] (lock_acquire) from [<c09ca59c>] (__mutex_lock+0x60/0xa0c)
[<c09ca59c>] (__mutex_lock) from [<c09cafd0>] (mutex_lock_nested+0x1c/0x24)
[<c09cafd0>] (mutex_lock_nested) from [<c068b0d0>] (ina2xx_set_shunt+0x70/0xb0)
[<c068b0d0>] (ina2xx_set_shunt) from [<c068b218>] (ina2xx_probe+0x88/0x1b0)
[<c068b218>] (ina2xx_probe) from [<c0673d90>] (i2c_device_probe+0x1e0/0x2d0)
[<c0673d90>] (i2c_device_probe) from [<c053a268>] (driver_probe_device+0x2b8/0x4a0)
[<c053a268>] (driver_probe_device) from [<c053a54c>] (__driver_attach+0xfc/0x120)
[<c053a54c>] (__driver_attach) from [<c05384cc>] (bus_for_each_dev+0x58/0x7c)
[<c05384cc>] (bus_for_each_dev) from [<c0539590>] (bus_add_driver+0x174/0x250)
[<c0539590>] (bus_add_driver) from [<c053b5e0>] (driver_register+0x78/0xf4)
[<c053b5e0>] (driver_register) from [<c0675ef0>] (i2c_register_driver+0x38/0xa8)
[<c0675ef0>] (i2c_register_driver) from [<c0102b40>] (do_one_initcall+0x48/0x18c)
[<c0102b40>] (do_one_initcall) from [<c0e00df0>] (kernel_init_freeable+0x110/0x1d4)
[<c0e00df0>] (kernel_init_freeable) from [<c09c8120>] (kernel_init+0x8/0x114)
[<c09c8120>] (kernel_init) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Fixes: 5d389b1251 ("hwmon: (ina2xx) Make calibration register value fixed")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ir35221 datasheet describes specific scaling factors for a number of
commands which the current driver applies when reading.
However now that the ir35221 has been tested on machines with more
easily verifiable readings these descriptions have turned out to be
superfluous and reading each command according to the linear format is
sufficient.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
An sht3x sensor include limits register which contains temperature
and humidity limit values. After a reset, pre-defined values are loaded
into that register. During the probe function, the driver reads the
limits register. However, if the reads are made too early, and the bus
is clocked at high frequencies (e.g. 100 kHz or more), the loading could be
not completed and the sensor returns a NACK which causes the probe to fail.
A delay of at least 500 us before the first read solves this issue.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building without CONFIG_LEDS_CLASS causes a link failure:
drivers/hwmon/pmbus/ibm-cffps.o: In function `ibm_cffps_probe':
ibm-cffps.c:(.text+0x4f4): undefined reference to `devm_of_led_classdev_register'
This adds the required dependency.
Fixes: ef9e1cdf41 ("hwmon: (pmbus/cffps) Add led class device ...")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This power supply device doesn't correctly manage it's own fault led.
Add an led class device and register it so that userspace can manage
power supply fault led as necessary.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This power supply device regularly fails to read VOUT_MODE due to the
CML bit going high. This results in an incorrect exponent used for the
voltage data, and therefore the power supply reports incorrect voltage.
Work around this by setting the pmbus flag to skip the CML check.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: f69316d62c ("hwmon: (pmbus) Add IBM Common Form Factor (CFF) ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ASPEED SoC must deassert a reset in order to use the PWM/tach
peripheral.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add debugfs entries for additional power supply data, including part
number, serial number, FRU number, firmware revision, ccin, and the
input history of the power supply. The input history is 10 minutes of
input power data in the form of twenty 30-second packets. Each packet
contains average and maximum power for that 30 second period.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
[groeck: Fixed endianness problem]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pmbus client drivers, if they want to use debugfs, should use the same
root directory as the pmbus debugfs entries are using. Therefore, export
the device dentry for the pmbus client.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Smatch reports:
drivers/hwmon/w83773g.c:105
get_fault() warn: shift has higher precedence than mask
Code analysis shows that the code is indeed wrong.
Fix it, and while we are at it, drop unnecessary typecast.
Fixes: 86a10c802362 ("hwmon: Add W83773G driver")
Cc: Lei YU <mine260309@gmail.com>
Reviewed-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sparse reports:
drivers/hwmon/hih6130.c:56: warning:
No description found for parameter 'client'
drivers/hwmon/hih6130.c:56: warning:
Excess struct member 'hwmon_dev' description in 'hih6130'
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sparse reports:
drivers/hwmon/sht21.c:60: warning:
No description found for parameter 'client'
drivers/hwmon/sht21.c:60:
warning: Excess struct member 'hwmon_dev' description in 'sht21'
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
sparse reports:
drivers/hwmon/hwmon.c:681: warning:
No description found for parameter 'chip'
drivers/hwmon/hwmon.c:681: warning:
Excess function parameter 'info' description in
'hwmon_device_register_with_info'
drivers/hwmon/hwmon.c:789: warning:
No description found for parameter 'chip'
drivers/hwmon/hwmon.c:789: warning:
No description found for parameter 'groups'
drivers/hwmon/hwmon.c:789: warning:
Excess function parameter 'info' description in
'devm_hwmon_device_register_with_info'
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo drivers/hwmon/pmbus/max31785.ko | grep alias
alias: i2c:max31785a
alias: i2c:max31785
After this patch:
$ modinfo drivers/hwmon/pmbus/max31785.ko | grep alias
alias: i2c:max31785a
alias: i2c:max31785
alias: of:N*T*Cmaxim,max31785aC*
alias: of:N*T*Cmaxim,max31785a
alias: of:N*T*Cmaxim,max31785C*
alias: of:N*T*Cmaxim,max31785
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calibration register is used for calculating current register in
hardware according to datasheet:
current = shunt_volt * calib_register / 2048 (ina 226)
current = shunt_volt * calib_register / 4096 (ina 219)
Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
order to avoid truncation error and provide best precision allowed
by shunt_voltage measurement. Make current scale value follow changes
of shunt_resistor from sysfs as calib_register value is now fixed.
Power_lsb value should also follow shunt_resistor changes as stated in
datasheet:
power_lsb = 25 * current_lsb (ina 226)
power_lsb = 20 * current_lsb (ina 219)
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The dual tachometer feature is implemented in hardware with a TACHSEL
input to indicate the rotor under measurement, and exposed on the device
by extending the READ_FAN_SPEED_1 word with two extra bytes*. The need
to read the non-standard four-byte response leads to a cut-down
implementation of i2c_smbus_xfer_emulated() included in the driver.
Further, to expose the second rotor tachometer value to userspace the
values are exposed through virtual pages. We re-route accesses to
FAN_CONFIG_1_2 and READ_FAN_SPEED_1 on pages 23-28 (not defined by the
hardware) to the same registers on pages 0-5, and with the latter command
we extract the value from the second word of the four-byte response.
* The documentation recommends the slower rotor be associated with
TACHSEL=0, which corresponds to the first word of the response. The
TACHSEL=0 measurement is used by the controller's closed-loop fan
management to judge target fan rate.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some circumstances call for virtual pages, to expose multiple values
packed into an extended PMBus register in a manner non-compliant with
the PMBus standard. An example of this is the Maxim MAX31785 controller,
which extends the READ_FAN_SPEED_1 PMBus register from two to four bytes
to support tach readings for both rotors of a dual rotor fan. This extended
register contains two word-sized values, one reporting the rate of the
fastest rotor, the other the rate of the slowest. The concept of virtual
pages aids this situation by mapping the page number onto the value to be
selected from the vectored result.
We should not try to set virtual pages on the device as such a page
explicitly doesn't exist; add a flag so we can avoid doing so.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The implementation makes use of the new fan control virtual registers
exposed by the pmbus core. It mixes use of the default implementations
with some overrides via the read/write handlers to handle FAN_COMMAND_1
on the MAX31785, whose definition breaks the value range into various
control bands dependent on RPM or PWM mode.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Expose fanX_target, pwmX and pwmX_enable hwmon sysfs attributes.
Fans in a PMBus device are driven by the configuration of two registers,
FAN_CONFIG_x_y and FAN_COMMAND_x: FAN_CONFIG_x_y dictates how the fan
and the tacho operate (if installed), while FAN_COMMAND_x sets the
desired fan rate. The unit of FAN_COMMAND_x is dependent on the
operational fan mode, RPM or PWM percent duty, as determined by the
corresponding configuration in FAN_CONFIG_x_y.
The mapping of fanX_target, pwmX and pwmX_enable onto FAN_CONFIG_x_y and
FAN_COMMAND_x is implemented with the addition of virtual registers to
facilitate the necessary side-effects of each access:
1. PMBUS_VIRT_FAN_TARGET_x
2. PMBUS_VIRT_PWM_x
3. PMBUS_VIRT_PWM_ENABLE_x
Some complexity arises with the fanX_target and pwmX attributes both mapping
onto FAN_COMMAND_x: There is no general mapping between PWM percent duty and
RPM, so we can't display values in either attribute in terms of the other
(which in my mind is the intuitive, if impossible, behaviour). This problem
also affects the pwmX_enable attribute which allows userspace to switch between
full speed, manual PWM and a number of automatic control modes, possibly
including a switch to RPM behaviour (e.g. automatically adjusting PWM duty to
reach a RPM target, the behaviour of fanX_target).
The next most intuitive behaviour is for fanX_target and pwmX to simply be
independent, to retain their most recently set value even if that value is not
active on the hardware (due to switching to the alternative control mode). This
property of retaining the value independent of the hardware state has useful
results for both userspace and the kernel: Userspace always sees a sensible
value in the attribute (the last thing it was set to, as opposed to 0 or
receiving an error on read), and the kernel can use the attributes as a value
cache. This latter point eases the implementation of pwmX_enable, which can
look up the associated pmbus_sensor object, take its cached value and apply it
to hardware on changing control mode. This ensures we will not arbitrarily set
a PWM value as an RPM value or vice versa, and we can assume that the RPM or
PWM value set was sensible at least at some point in the past.
Finally, the DIRECT mode coefficients of some controllers is different between
RPM and PWM percent duty control modes, so PSC_PWM is introduced to capture the
necessary coefficients. As pmbus core had no PWM support previously PSC_FAN
continues to be used to capture the RPM DIRECT coefficients, but in order to
avoid falsely applying RPM scaling to PWM values I have introduced the
PMBUS_HAVE_PWM12 and PMB_BUS_HAVE_PWM34 feature bits. These feature bits allow
drivers to explicitly declare PWM support in order to have the attributes
exposed.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Use pci_get_domain_bus_and_slot() with a domain number of 0 where we can't
extract the domain number. Other places, use the actual domain number from
the device.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'default n' is default, so there is no need to specify it explicitly.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Nuvoton W83773G is a hardware monitor IC providing one local
temperature and two remote temperature sensors.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the thermal subsystem returne -EPROBE_DEFER or any other error
when hwmon calls devm_thermal_zone_of_sensor_register(), this is
silently ignored.
I ran into this with an incorrectly defined thermal zone, making
it non-existing and thus this call failed with -EPROBE_DEFER
assuming it would appear later. The sensor was still added
which is incorrect: sensors must strictly be added after the
thermal zones, so deferred probe must be respected.
Fixes: d560168b5d ("hwmon: (core) New hwmon registration API")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With a nxp,se97 chip on an atmel sama5d31 board, the I2C adapter driver
is not always capable of avoiding the 25-35 ms timeout as specified by
the SMBUS protocol. This may cause silent corruption of the last bit of
any transfer, e.g. a one is read instead of a zero if the sensor chip
times out. This also affects the eeprom half of the nxp-se97 chip, where
this silent corruption was originally noticed. Other I2C adapters probably
suffer similar issues, e.g. bit-banging comes to mind as risky...
The SMBUS register in the nxp chip is not a standard Jedec register, but
it is not special to the nxp chips either, at least the atmel chips
have the same mechanism. Therefore, do not special case this on the
manufacturer, it is opt-in via the device property anyway.
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Power values in the 100s of watt range can easily blow past
32bit math limits when processing everything in microwatts.
Use 64bit math instead to avoid these issues on common 32bit ARM
BMC platforms.
Fixes: 442aba7872 ("hwmon: PMBus device driver")
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- Drivers for MAX31785 and MAX6621
- Support for AMD family 17h (Ryzen, Threadripper) temperature sensors
- Various driver cleanups and minor improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NpxT
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- drivers for MAX31785 and MAX6621
- support for AMD family 17h (Ryzen, Threadripper) temperature sensors
- various driver cleanups and minor improvements
* tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (30 commits)
dt-bindings: pmbus: Add Maxim MAX31785 documentation
pmbus: Add driver for Maxim MAX31785 Intelligent Fan Controller
hwmon: (aspeed-pwm-tacho) Sort headers
hwmon: (xgene) Minor clean up of ifdef and acpi_match_table reference
hwmon: (max6621) Inverted if condition in max6621_read()
hwmon: (asc7621) remove redundant assignment to newval
hwmon: (xgene) Support hwmon v2
hwmon: (gpio-fan) Fix null pointer dereference at probe
hwmon: (gpio-fan) Convert to use GPIO descriptors
hwmon: (gpio-fan) Rename GPIO line state variables
hwmon: (gpio-fan) Get rid of the gpio alarm struct
hwmon: (gpio-fan) Get rid of platform data struct
hwmon: (gpio-fan) Mandate OF_GPIO and cut pdata path
hwmon: (gpio-fan) Send around device pointer
hwmon: (gpio-fan) Localize platform data
hwmon: (gpio-fan) Use local variable pointers
hwmon: (gpio-fan) Move DT bindings to the right place
Documentation: devicetree: add max6621 device
hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor
hwmon: (w83793) make const array watchdog_minors static, reduces object code size
...
The Maxim MAX31785 is a PMBus device providing closed-loop, multi-channel
fan management with temperature and remote voltage sensing. It supports
various fan control features, including PWM frequency control, temperature
hysteresis, dual tachometer measurements, and fan health monitoring.
This patch presents a basic driver using only the existing features of the
PMBus subsystem.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
[groeck: Modified description to clarify that fan control is not yet provided]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the un-necessary ifdef CONFIG_ACPI and directly
uses the acpi_match_table from the driver pdev.
Signed-off-by: Hoan Tran <hotran@apm.com>
[groeck: Dropped unnecessary initialization]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We intended to test for failure here but accidentally tested for
success. It means that we don't set "*val" to true and it means that
if i2c_smbus_write_byte() does fail then we return success.
Fixes: e7895864b0d7 ("hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The setting of newval to zero is redundant as the following if/else
stanzas will always update newval to a new value. Remove the
redundant setting, cleans up clang build warning:
drivers/hwmon/asc7621.c:582:2: warning: Value stored to 'newval' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch supports xgene-hwmon v2 which uses the non-cachable memory
as the PCC shared memory.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A previous commit changed the argument list of gpio_fan_get_of_data(),
removing the "struct *dev" argument and retrieving it instead from the
gpio_fan_data structure. The "dev" entry of gpio_fan_data was then
dereferenced to access the of_node field, leading to a kernel panic
during the probe as the "dev" entry of the gpio_fan_data structure was
not filled yet.
Fix this by setting fan_data->dev before calling gpio_fan_get_of_data().
Fixes: 5859d8d30737 ("hwmon: (gpio-fan) Get rid of platform data struct")
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This converts the GPIO fan driver to use GPIO descriptors. This way
we avoid indirection since the gpiolib anyway just use descriptors
inside, and we also get rid of explicit polarity handling: the
descriptors internally knows if the line is active high or active
low.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[groeck: Line length]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The "ctrl" and "num_ctrl" entries in the state container struct is
ambiguously named "ctrl" and "num_ctrl" overlapping with some hwmon
lingo and making it hard to understand. Since this array actually
contains the GPIO line numbers, from the Linux global GPIO numberspace,
used to control the different fan speeds. Rename these fields to
"gpios" (pluralis) and "num_gpios" so as to make it unambiguous.
Convert some instances of "unsigned" to "unsigned int" to keep
checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no point in storing the GPIO alarm settings in their
own struct so merge this into the main state container.
Convert the variables from "unsigned" to "unsigned int" to
make checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We are not passing the platform data struct into the driver from the
outside, there is no point of having it around separately so instead
of first populating the platform data struct and assigning the result
into the same variables in the state container (struct gpio_fan_data)
just assign the configuration from the device tree directly into the
state container members.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We have no users of platform data, we made platform data driver-local,
so cut all #ifdefs for the platform data case, and depend on the
Kconfig CONFIG_OF_GPIO symbol.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver is storing the struct platform_device *pdev pointer
but what it is really using and want to pass around is a
struct device *dev pointer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is not a single user of the platform data header in
<linux/gpio-fan.h>. We can conclude that all current users are
probing from the device tree, so start simplifying the code by
pulling the header into the driver.
Convert "unsigned" to "unsigned int" in the process to make
checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Create local struct device *dev and device_node *np pointers to
make the code easier to read.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6621 is a PECI-to-I2C translator provides an efficient, low-cost
solution for PECI-to-SMBus/I2C protocol conversion. It allows reading the
temperature from the PECI-compliant host directly from up to four
PECI-enabled CPUs.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't populate const array watchdog_minors on the stack, instead make it
static. Makes the object code smaller by over 350 bytes:
Before:
text data bss dec hex filename
48019 38144 256 86419 15193 drivers/hwmon/w83793.o
After:
text data bss dec hex filename
47574 38232 256 86062 1502e drivers/hwmon/w83793.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The previous value reduced the time required to determine
the fan value, however, it's also used as the final timeout
mechanism. The prevous value would work for any fan speed
greater than around 3k RPM. This increased value, lets the fan
speeds return quickly but will wait longer to handle speeds below 3k
RPM.
Testing: this value was determined through experimentation on the ast2400
on the Quanta-q71l. This configurations runs 8 fans attached to the
controller.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add new device tree binding for max1619.
Signed-off-by: Alan Tull <atull@kernel.org>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A previous commit removed bit or'ing into to the integer status
so now status is now always zero. This means that the non-zero check on
status and the sht15_send_status call will never occur; it is deadcode.
Clean this up by removing the dead code.
Detected by: CoverityScan CID#1456835 ("Logically dead code")
Fixes: aa7ab80c578c ("hwmon: (sht15) Root out platform data")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After finding out there are active users of this sensor I noticed:
- It has a single PXA27x board file using the platform data
- The platform data is only used to carry two GPIO pins, all other
fields are unused
- The driver does not use GPIO descriptors but the legacy GPIO
API
I saw we can swiftly fix this by:
- Killing off the platform data entirely
- Define a GPIO descriptor lookup table in the board file
- Use the standard devm_gpiod_get() to grab the GPIO descriptors
from either the device tree or the board file table.
This compiles, but needs testing.
Cc: arm@kernel.org
Cc: Marco Franchi <marco.franchi@nxp.com>
Cc: Davide Hug <d@videhug.ch>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for handling temperature offset values for various AMD CPUs,
similar to the code used in the coretemp driver for Intel CPUs. This is
primarily for Ryzen CPUs (which has documented temperature offsets),
but the code is kept generic to simplify adding additional CPUs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Introduce a local data structure and determine the temperature read
function at probe time to reduce runtime complexity.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function snprintf already cares for the terminating NUL at the end of
the string, the caller doesn't need to do it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Andrea Merello <andrea.merello@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus core may call read/write word data functions with a page value
of -1, intending to perform the operation without setting the page.
However, the read/write word data functions accept only unsigned 8-bit
page numbers, and therefore cannot check for negative page number to
avoid setting the page. This results in setting the page number to 0xFF.
This may result in errors or undefined behavior of some devices
(specifically the ir35221, which allows the page to be set to 0xFF,
but some subsequent operations to read registers may fail).
Switch the pmbus_set_page page parameter to an integer and perform the
check for negative page there. Make read/write functions consistent in
accepting an integer page number parameter.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Fixes: cbcdec6202 ("hwmon: (pmbus): Access word data for STATUS_WORD")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read
delay") reduced the initial temperature read delay and made it dependent
on the chip's shutdown mode. If the chip was not in shutdown mode at probe,
the read delay no longer applies.
This ignores the fact that the chip initialization changes the temperature
sensor resolution, and that the temperature register values change when
the resolution is changed. As a result, the reported temperature is twice
as high as the real temperature until the first temperature conversion
after the configuration change is complete. This can result in unexpected
behavior and, worst case, in a system shutdown. To fix the problem,
let's just always wait for a conversion to complete before reporting
a temperature.
Fixes: 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read delay")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197167
Reported-by: Ralf Goebel <ralf.goebel@imago-technologies.com>
Cc: Ralf Goebel <ralf.goebel@imago-technologies.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TSI channel, which is usually used for touchscreen support, but can
be used as 4 general purpose ADCs. When used as a touchscreen interface
the touchscreen driver switches the device into 1ms sampling mode (rather
than the default 10ms economy mode) as recommended by the manufacturer.
When using the TSI channels as a general purpose ADC we are currently not
doing this and testing suggests that this can result in ADC timeouts:
[ 5827.198289] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5827.728293] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5993.808335] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.328441] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.848291] da9052 spi2.0: timeout waiting for ADC conversion interrupt
Switching to the 1ms timing resolves this issue.
Fixes: 4f16cab19a ("hwmon: da9052: Add support for TSI channel")
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 2ca492e22c has moved the call to 'kfifo_alloc()' from after the
main 'if' statement to before it.
But it has not updated the error handling paths accordingly.
Fix all that:
- if 'kfifo_alloc()' fails we can return directly
- direct returns after 'kfifo_alloc()' must now go to 'out_mbox_free'
- 'goto out_mbox_free' must be replaced by 'goto out', otherwise the
'[pcc_]mbox_free_channel()' call will be missed.
Fixes: 2ca492e22c ("hwmon: (xgene) Fix crash when alarm occurs before driver probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add the lantiq cpu temperature sensor support for xrx200.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't populate the arrays on the stack, instead make them static.
Makes the object code smaller by over 950 bytes:
Before:
text data bss dec hex filename
26144 18768 352 45264 b0d0 drivers/hwmon/asc7621.o
After:
text data bss dec hex filename
25029 18928 352 44309 ad15 drivers/hwmon/asc7621.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TI LM5066I hotswap controller is a more accurate version of the
LM5066 device already supported. It has different measurement conversion
coefficients than the LM5066, so it needs to be recognized as a
different device.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When converting the DIRECT format CURRENT_IN and POWER commands, make
the offset coefficient ("b") predicate on the value of the current limit
setting.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps:
- VR13.0 mode, 10-mV DAC - 0x24
- VR13.0 mode, 5-mV DAC - 0x27
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the driver to monitor IBM CFF power supplies with hwmon over
pmbus.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
[groeck: drop 'default n'; include bitops.h instead of jiffies.h]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TSI channel has a 4 channel mux connected to it and is normally
used for touchscreen support. The hardware may alternatively
use it as general purpose adc.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix checkpatch warnings about S_IRUGO being less readable than
providing the permissions octal as '0444'.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With CONFIG_THERMAL=m, a built-in aspeed pwm tacho driver causes
a link error:
drivers/hwmon/aspeed-pwm-tacho.o: In function `aspeed_pwm_tacho_probe':
aspeed-pwm-tacho.c:(.text+0x7f0): undefined reference to `thermal_of_cooling_device_register'
This adds a dependency similar to what other hwmon drivers use,
ensuring that the aspeed driver cannot be built-in in this
case but has to be a module. With THERMAL=n, we still allow building it.
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Export all the available status registers through debugfs. This is
useful for hardware diagnostics, especially on multi-page pmbus devices,
as user-space access of the i2c space could corrupt the pmbus page
accounting.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support in aspeed-pwm-tacho driver for cooling device creation.
This cooling device could be bound to a thermal zone
for the thermal control. Device will appear in /sys/class/thermal
folder as cooling_deviceX. Then it could be bound to particular
thermal zones. Allow specification of the cooling levels
vector - PWM duty cycle values in a range from 0 to 255
which correspond to thermal cooling states.
Signed-off-by: Mykola Kostenok <c_mykolak@mellanox.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add PB_STATUS_INPUT as the generic alarm bit for iin and pin. We also
need to redo the status register checking before setting up the boolean
attribute, since it won't necessarily check STATUS_WORD if the device
doesn't support it, which we need for this bit.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pmbus always reads byte data from the status register, even if
configured to use STATUS_WORD. Use a function pointer to read the
correct amount of data from the registers.
Also switch to try STATUS_WORD first before STATUS_BYTE on init.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the storage of status registers to 16 bit values. This allows us
to store all the bits of STATUS_WORD.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After a suspend / resume cycle we possibly need to reapply chip registers
settings that we had set or fixed in a probe path, since they might have
been reset to default values or set incorrectly by a BIOS again.
Tested on a Gigabyte M720-US3 board, which requires routing internal VCCH5V
to in7 (and had it wrong again on resume from S3).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
[groeck: Return value from it87_resume_sio() is unused; make it void]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit splits out chip registers setting code on probe path to
separate functions so they can be reused for setting the device properly
again when system resumes from suspend.
While we are at it let's also make clear that on IT8720 and IT8782 it's
the VCCH5V line that is (possibly) routed to in7.
This will make it consistent with a similar message that it printed on
IT8783.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3562 320 8 3890 f32 drivers/hwmon/i5k_amb.o
File size After adding 'const':
text data bss dec hex filename
3658 224 8 3890 f32 drivers/hwmon/i5k_amb.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
10055 7032 0 17087 42bf drivers/hwmon/adt7475.o
File size After adding 'const':
text data bss dec hex filename
10567 6520 0 17087 42bf drivers/hwmon/adt7475.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2304 2936 0 5240 1478 drivers/hwmon/adc128d818.o
File size After adding 'const':
text data bss dec hex filename
2344 2872 0 5216 1460 drivers/hwmon/adc128d818.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6161 9400 0 15561 3cc9 drivers/hwmon/nct7802.o
File size After adding 'const':
text data bss dec hex filename
6465 9080 0 15545 3cb9 drivers/hwmon/nct7802.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6655 304 0 6959 1b2f drivers/hwmon/hwmon.o
File size After adding 'const':
text data bss dec hex filename
6703 240 0 6943 1b1f drivers/hwmon/hwmon.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If stts751 hw by some reason reports conversion rate bigger then 9:
ret = i2c_smbus_read_byte_data(priv->client, STTS751_REG_RATE);
then dereferencing stts751_intervals[priv->interval] leads to buffer
overrun.
The patch adds sanity check for value stored on chip.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 7f07ec0fa1 ("hwmon: new driver for ST stts751 thermal sensor")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
sysfs store functions should return the number of bytes written.
Returning zero results in an endless loop.
Fixes: 08426eda58 ("hwmon: Add driver for FTS BMC chip "Teutates"")
Signed-off-by: Thilo Cestonaro <thilo.cestonaro@ts.fujitsu.com>
[groeck: Clean up documentation change and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
gcc 7.1 complains that the driver uses sprintf() and thus does not validate
the length of output buffers.
drivers/hwmon/applesmc.c: In function 'applesmc_show_fan_position':
drivers/hwmon/applesmc.c:82:21: warning:
'%d' directive writing between 1 and 5 bytes into a region of size 4
Fix the problem by using scnprintf() instead of sprintf() throughout the
driver. Also explicitly limit the number of supported fans to avoid actual
buffer overruns and thus invalid keys.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The reference driver polled but mentioned it was possible to sleep
for a computed period to know when it's ready to read. However, polling
with minimal sleeps is quick and works. This also improves responsiveness
from the driver.
Testing: tested on ast2400 on quanta-q71l
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reduce the fan_tach period such that the fan controller uses a shorter
period to measure the rpm.
The original period of 0x1000 was chosen as a conversative value from the
reference implementation. Through experimentation on the quanta-q71l
board, I was able to drive the number down which ultimately reduced the
time the controller would use to determine the fan_tach. This value was
recently tested and accepted downstream on the IBM Zaius board which uses
the ast2500.
Future work: It may be worthwhile as this is a tunable parameter to the
system, to allow overriding it through the device tree.
Testing: Tested on an ast2400 sitting on a quanta-q71l and ast2500 on
power9.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch exports current(A) sensors in inband sensors copied to
main memory by OCC.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Today, the type of a PowerNV sensor system is determined with the
"compatible" property for legacy Firmwares and with the "sensor-type"
for newer ones. The same array of strings is used for both to do the
matching and this raises some issue to introduce new sensor types.
Let's introduce two different arrays (legacy and current) to make
things easier for new sensor types.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The implementation details for SCPI seems to suggest that the sensor
readings must be reported by SCP using a well defined scale
(millidegree Celsius for temperature, millivolts for voltage,
milliamperes for current, microwatts for power and microjoules for
energy).
This is also important for the interaction with other subsystems: for
example both the thermal sub-system and the hwmon sysfs interface expect
the temperature expressed in millidegree Celsius.
Unfortunately since this behaviour is dependent on the firmware
implementation there are cases where the sensor readings are reported
using a different scale. For example in the Amlogic SoCs the
temperature is reported in degree and not millidegree Celsius.
To take into account this discrepancy and fixup the values reported by
SCP a new compatible 'amlogic,meson-gxbb-scpi-sensors' is introduced and
used in this patch by the scpi-hwmon driver to convert the sensor
readings to the expected scale.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The aspeed-pwm-tacho controller supports measuring the fan tach by using
leading, falling, or both edges. This change allows the driver to
support either of the three configurations and will appropriately modify
the returned tach data.
If the controller is measuring with both edges it can return a value more
quickly to the requestor. This version of the driver should still take ~1s
to return with an RPM value per fan, however, it can be tuned faster with
double edge counting enabled than without.
I tested this and found the number returned matched what I expected.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
OCC provides historical minimum and maximum value for the sensor
readings. This patch exports them as highest and lowest attributes
for the inband sensors copied by OCC to main memory.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When enabled temperature smoothing allows ramping the fan speed over a
configurable period of time instead of jumping to the new speed
instantaneously.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Systems using 4-wire fans usually require high frequency (22.5kHz)
output on the pwm. Add 22500 as a valid option in the pwmfreq_table. In
high frequency mode the low-order bit are ignored so they can safely be
set to 0.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By default adt7475 will stop the fans (pwm duty cycle 0%) when the
temperature drops past Tmin - hysteresis. Some systems want to keep the
fans moving even when the temperature drops so add new sysfs attributes
that configure the enhanced acoustics min 1-3 which allows the fans to
run at the minimum configure pwm duty cycle.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475 has had find_nearest() since it's creation in 2009. Since
then find_closest() has been introduced and several drivers have been
updated to use it. Update the adt7475 to use find_closest() and remove
the now unused find_nearest().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IR35221 is a Digital DC-DC Multiphase Converter
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
[groeck: Preserve alphabetic order in Kconfig;
add missing break statements (from Dan Carpenter);
add missing error checks]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Recent chips support multiple pins for fan speed inputs and fan control
outputs. Examine all of them to determine supported fan controls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of checking if a temperature source has a label, use a bit mask
to determine if a temperature source is valid for a given chip.
This simplifies the code and, if necessary, lets us support chips with
unknown or incomplete labels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make fan and pwm names in sysfs start with index 1 in accordance to
Documentation/hwmon/sysfs-interface conventions.
Current implementation starts with index 0, making tools such as
sensors(1) skip the first fan.
Signed-off-by: Stefan Schaeckeler <sschaeck@cisco.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Call of_node_put() on a node claimed with of_node_get() or by any other
means such as for_each_child_of_node().
Signed-off-by: Stefan Schaeckeler <sschaeck@cisco.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When the controller fails to provide an RPM reading within the alloted
time; the driver returns -ETIMEDOUT and no file contents.
Signed-off-by: Patrick Venture <venture@google.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver uses regmap and thus has to select it to avoid build
errors such as the following.
drivers/hwmon/aspeed-pwm-tacho.c:337:21: error: variable
'aspeed_pwm_tacho_regmap_config' has initializer but incomplete type
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The recent conversion to the hotplug state machine missed that the original
hotplug notifiers did not execute in the frozen state, which is used on
suspend on resume.
This does not matter on single socket machines, but on multi socket systems
this breaks when the device for a non-boot socket is removed when the last
CPU of that socket is brought offline. The device removal locks up the
machine hard w/o any debug output.
Prevent executing the hotplug callbacks when cpuhp_tasks_frozen is true.
Thanks to Tommi for providing debug information patiently while I failed to
spot the obvious.
Fixes: e00ca5df37 ("hwmon: (coretemp) Convert to hotplug state machine")
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver is no longer needed:
* It has no mainline users
* It has no DT support and OMAP is DT only
* iio-hwmon can be used for madc, which also works with DT
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7475 and ADT7476 have the STRT bit cleared by default[1]. Before any
monitoring activities the STRT bit needs to be set. Logically this needs
to happen before any of the sensors are read so the probe() function
seems the best place for it.
[1] - https://www.onsemi.com/pub/Collateral/ADT7475-D.PDF
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt voltage and current registers are signed 16-bit values so
handle them as such.
Signed-off-by: Joe Schaack <jschaack@xes-inc.com>
Reviewed-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C device ID entries set a .driver_data but this data is never
looked up by the driver. So don't set it and also remove the enum.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports.
The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer
inputs.
The device driver matches on the device tree node. The configuration
values are read from the device tree and written to the respective
registers.
The driver provides a sysfs entries through which the user can
configure the duty-cycle value (ranging from 0 to 100 percent) and read
the fan tach rpm value.
Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently there is no method for setting the channel
value from the DTS file. When, the driver uses a dts
file to initialize the driver platform_data is not set.
As a result channel variable may not be set correctly.
Without the channel variable set correctly, some of the
sensors will not be initialized correctly. For example
temp3 sensor sysfs entries.
This implements the schema agreed with the device tree
binding document.
Signed-off-by: Mahoda Ratnayaka <mahoda.ratnayaka@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding the ability for the ads7828 and ads7830 to use device tree to
get optional parameters instead of using platform devices. This allows
people using custom boards to also use the ads7828 in a non-default manner.
Signed-off-by: Sam Povilus <kernel.development@povil.us>
[groeck: Fixed whitespace errors in ads7828.txt]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It was reported that dell-smm-hwmon is working fine on Dell XPS 15 9560.
Link: http://www.spinics.net/lists/platform-driver-x86/msg10751.html
Reported-by: Vasile Dumitrescu <vasile.dumitrescu@undeva.eu>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The read_string callback is supposed to retrieve a pointer to a
constant string.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Serialize access to the hardware by using "request_muxed_region".
Call to this macro will hold off the requestor if the resource is
currently busy. "superio_enter" will return an error if call to
"request_muxed_region" fails.
Signed-off-by: Katsumi Sato <sato@toshiba-tops.co.jp>
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Seems like coefficient values for m, b and R under power have been
put in the wrong order. Rearranging them properly to get correct
values of coefficients for power.
For specs, please refer to table 7 (page 35) on
http://www.analog.com/media/en/technical-documentation/data-sheets/ADM1075.pdf
Fixes: 904b296f30 ("hwmon: (adm1275) Introduce configuration data structure for coeffcients")
Signed-off-by: Shikhar Dogra <shidogra@cisco.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The latest gcc-7 snapshot adds a warning to point out that when
atk_read_value_old or atk_read_value_new fails, we copy
uninitialized data into sensor->cached_value:
drivers/hwmon/asus_atk0110.c: In function 'atk_input_show':
drivers/hwmon/asus_atk0110.c:651:26: error: 'value' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Adding an error check avoids this. All versions of the driver
are affected.
Fixes: 2c03d07ad5 ("hwmon: Add Asus ATK0110 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8705F is known to respond on both SIO addresses. Registering it twice
may result in system lockups.
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: e84bd9535e ("hwmon: (it87) Add support for second Super-IO chip")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Traced fans not spinning to incorrect PWM value being written.
The passed in value was written instead of the calulated value.
Fixes: 54187ff9d7 ("hwmon: (max31790) Convert to use new hwmon registration API")
Signed-off-by: Alex Hemme <ahemme@cisco.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the driver to work with device tree support.
Based on initial patch submission from Peter Fox.
Tested on a imx7d-sdb board connected to a SHT15 board via Mikro Bus.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip is similar to IT8732E, but supports only three fans
and pwm outputs instead of four (the driver currently does not
support the 4th fan and pwm output of IT8732E).
Note that the chip ID is 0x8733, not 0x8792 as one would expect.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In IT8620E, after setting pwm control to manual, it was observed that
pwm values for fan 4..6 have reversed results (writing 0 results in fans
running at full speed, writing 255 results in fans turned off).
With the new PWM control, pwm polarity for pwm control 4..6 is specified
in its pwm control registers. Those registers are overwritten when setting
the pwm mode or the temperature mapping. Do not touch bit 2..6 of pwm
control registers on register writes to fix the problem.
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm4 is enabled if bit 2 of GPIO control register 4 is disabled,
not when it is enabled. Since the check is for the skip condition,
it is reversed. This applies to both IT8620 and IT8628.
Fixes: 36c4d98a78 ("hwmon: (it87) Add support for all pwm channels ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If sensor attributes were never read, the pwm control data has not been
initiialized, which can cause wrong driver behavior. Ensure that cached
data is current before acting on it.
Cc: stable@vger.kernel.org # 4.4+
Reported-by: Kevin Folz <kfolz@evertz.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Configuration registers on ITE8622 are different to 8620 and 8628 and
require special handling. Also, the chip supports up to 5 pwm controls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8622E is similar to IT8620E, but only supports five pwm controls and
five fan tachometers.
Originally-from: Kevin Folz <kfolz@evertz.com>.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On IT8622E and IT8628E, VIN3 is expected to be connected to +5V.
Add feature flag and reflect in input label.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rgistering a thermal zone uses devm_kzalloc(), which requires
a pointer to the parent device.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While invalid name attributes are really not desirable and do mess up
libsensors, enforcing valid names has the detrimental effect of driving
users away from using the new hardware monitoring API, especially those
registering name attributes violating the ABI restrictions. Another
undesirable side effect is that this violation and the resulting error
may only be discovered some time after a conversion to the new API,
which in turn may trigger a revert of that conversion.
To solve the problem, relax validation and only issue a warning instead
of returning an error if a name attribute violating the ABI is provided.
This lets callers continue to provide invalid name attributes while
notifying them about it.
Many thanks are due to Dmitry Torokhov for the idea.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It does not make sense to use one of the the new APIs when not
even providing a name attribute. Make it mandatory.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Texas Instruments TMP122/124 which are nearly identical to
their TMP121/123 except that they also support programmable temperature
thresholds.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We have a device reference, utilize it instead of pr_warn().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/hwmon/ltc4151.ko | grep alias
alias: i2c:ltc4151
After this patch:
$ modinfo drivers/hwmon/ltc4151.ko | grep alias
alias: i2c:ltc4151
alias: of:N*T*Clltc,ltc4151C*
alias: of:N*T*Clltc,ltc4151
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Preserve chip operation mode if no mode is specified via devicetree. This
enables operation when chip configuration is done by BIOS/ROMMON.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for operation modes 1-3 of the ADC128D818 (see datasheet sec.
8.4.1). These differ in the number and type of the available input signals,
requiring the driver to selectively hide sysfs nodes according to the
operation mode configured via devicetree.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Implement operation mode selection using the optional 'ti,mode' devicetree
property (see [1]). The ADC128D818 supports four operation modes differing
in the number and type of input readings (see datasheet, sec. 8.4.1), of
which mode 0 is the default.
We only add handling of the 'ti,mode' property here, the driver still
supports nothing else than the default mode 0.
[1] Documentation/devicetree/bindings/hwmon/adc128d818.txt
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
tmp401 separately read/wrote high and low bytes of temperature values while
the hardware supports reading/writing those values in one operation. Driver
has been modified to use word operations where possible.
Tested with a tmp432 sensor on a mips64 platform.
Signed-off-by: Jeroen De Wachter <jeroen.de_wachter.ext@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into limit attributes can overflow due to multplications and
additions with unbound input values. Writing into fan limit attributes
can result in a crash with a division by zero if very large values are
written and the fan divider is larger than 1.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into limit attributes can overflow due to additions and
multiplications with unchecked parameters.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into voltage limit, temperature limit, temperature hysteresis,
and temperature zone attributes can overflow due to unclamped parameters
to multiplications, additions, and subtractions.
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Expose the per-chip unique identifier so it can be used to identify the
sensor producing the measurements.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
