VFs may hit VF-PF channel timeout while probing, as in some
cases it was observed that VF FLR and VF "acquire" message
transaction (i.e first message from VF to PF in VF's probe flow)
could occur simultaneously which could lead VF to fail sending
"acquire" message to PF as VF is marked disabled from HW perspective
due to FLR, which will result into channel timeout and VF probe failure.
In such cases, try retrying VF "acquire" message so that in later
attempts it could be successful to pass message to PF after the VF
FLR is completed and can be probed successfully.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF is always configured to drop control frames
(with reserved mac addresses) but to work LACP
on the VFs, it would require LACP control frames
to be forwarded or transmitted successfully.
This patch fixes this in such a way that trusted VFs
(marked through ndo_set_vf_trust) would be allowed to
pass the control frames such as LACP pdus.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running tx switched traffic between VNICs
created via a bridge(to which VFs are added),
adapter drops the unicast packets in tx flow due to
VNIC's ucast mac being unknown to it. But VF interfaces
being in promiscuous mode should have caused adapter
to accept all the unknown ucast packets. Later, it
was found that driver doesn't really configure tx
promiscuous mode settings to accept all unknown unicast macs.
This patch fixes tx promiscuous mode settings to accept all
unknown/unmatched unicast macs and works out the scenario.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in i596_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <albin_yang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If phy_power_on() fails in rk_gmac_powerup(), clocks are left enabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reading phy registers via Clause 45 MDIO protocol, after write
address operation, the driver use another write address operation, so
can not read the right value of any phy registers. This patch fixes it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hns driver of earlier devices, when autoneg off, restart autoneg
will return -EINVAL, so make the hns driver for the latest devices
do the same.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns enet driver, we use of_parse_handle() to get hold of the
device node related to "ae-handle" but we have missed to put
the node reference using of_node_put() after we are done using
the node. This patch fixes it.
Note:
This problem is stated in Link: https://lkml.org/lkml/2018/12/22/217
Fixes: 48189d6aaf ("net: hns: enet specifies a reference to dsaf")
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcS2rdAAoJEEg/ir3gV/o+CZ8IAMX4yWUWjzgrIDdOc1OEgHJQ
FDCMtTDm/I+m1UInAgoigRia2RyIL99N81Vrx+p+otCOml/U5IXPt5tuJfSNQYZ3
p9MibQSXtKJ9jhowOVZdYlTx9CXti75BS45wHKZPlL7V+gCC2Q7/8aviuRlkQKAN
4pQNDreNiiB8PznXG/yCyzEu0Kc9M/Bv89xdLynVpDTxBfEfI8xSv4PttUcAxaQ5
Fs/489wuODyhAczOquQj1dvn61zUamaPp6z0h+GbZOCQv0AO7ABRZl+7o5C5r+rA
i7R4ak6WIgW3snIzhCdpynPfas8kUIvxJjkNCZuoFsefrBRsNv5RvtfCkuzyms4=
=3epF
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-01-25' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-01-25
This series introduces some fixes to mlx5 driver.
For more information please see tag log below.
Please pull and let me know if there is any problem.
For -stable v4.13
('net/mlx5e: Allow MAC invalidation while spoofchk is ON')
For -stable v4.18
('Revert "net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager"')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If fill_level was not zero and status was not BUSY,
result of "tx_prod - tx_cons - inuse" might be zero.
Subtracting 1 unconditionally results invalid negative return value
on this case.
Make sure not to return an negative value.
Signed-off-by: Tomonori Sakita <tomonori.sakita@sord.co.jp>
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Reviewed-by: Dalon L Westergreen <dalon.westergreen@linux.intel.com>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that libvirt uses 0-vid as a default if no vlan was
set for the guest (which is the case for switchdev mode) and errs
if we disallow that:
error: Failed to start domain vm75
error: Cannot set interface MAC/vlanid to 6a:66:2d:48:92:c2/0 \
for ifname enp59s0f0 vf 0: Operation not supported
So allow this in order not to break existing systems.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Gavi Teitz <gavi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
With VF LAG commit 491c37e49b "net/mlx5e: In case of LAG, one switch
parent id is used for all representors", both uplinks and all the VFs
(on both of them) get the same switchdev id.
This cause the provisioning system method to identify the rep of a given
VF from the parent PF PCI device using switchev id and physical port
name to break, since VFm of PF0 will have the (id, name) as VFm of PF1.
To fix that, we align to use the framework agreed upstream and set by
nfp commit 168c478e10 "nfp: wire get_phys_port_name on representors":
$ cat /sys/class/net/eth4_*/phys_port_name
p0
pf0vf0
pf0vf1
Now, the names will be different, e.g. pf0vf0 vs. pf1vf0.
Fixes: 491c37e49b ("net/mlx5e: In case of LAG, one switch parent id is used for all representors")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Waleed Musa <waleedm@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Prior to this patch the driver prohibited spoof checking on invalid MAC.
Now the user can set this configuration if it wishes to.
This is required since libvirt might invalidate the VF Mac by setting it
to zero, while spoofcheck is ON.
Fixes: 1ab2068a4c ("net/mlx5: Implement vports admin state backup/restore")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The lock in qp_table might be taken from process context or from
interrupt context. This may lead to a deadlock unless it is taken with
IRQs disabled.
Discovered by lockdep
================================
WARNING: inconsistent lock state
4.20.0-rc6
--------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W}
python/12572 [HC1[1]:SC0[0]:HE0:SE1] takes:
00000000052a4df4 (&(&table->lock)->rlock#2){?.+.}, /0x50 [mlx5_core]
{HARDIRQ-ON-W} state was registered at:
_raw_spin_lock+0x33/0x70
mlx5_get_rsc+0x1a/0x50 [mlx5_core]
mlx5_ib_eqe_pf_action+0x493/0x1be0 [mlx5_ib]
process_one_work+0x90c/0x1820
worker_thread+0x87/0xbb0
kthread+0x320/0x3e0
ret_from_fork+0x24/0x30
irq event stamp: 103928
hardirqs last enabled at (103927): [] nk+0x1a/0x1c
hardirqs last disabled at (103928): [] unk+0x1a/0x1c
softirqs last enabled at (103924): [] tcp_sendmsg+0x31/0x40
softirqs last disabled at (103922): [] 80
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&table->lock)->rlock#2);
lock(&(&table->lock)->rlock#2);
*** DEADLOCK ***
Fixes: 032080ab43 ("IB/mlx5: Lock QP during page fault handling")
Signed-off-by: Moni Shoua <monis@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MLX5E_PFLAG_* definitions were changed from bitmask to enumerated
values. However, in mlx5e_open_rq(), the proper API (MLX5E_GET_PFLAG macro)
was not used to read the flag value of MLX5E_PFLAG_RX_NO_CSUM_COMPLETE.
Fixed it.
Fixes: 8ff57c18e9 ("net/mlx5e: Improve ethtool private-flags code structure")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This reverts commit 5f5991f36d.
With the original commit, eswitch instance will not be initialized for
a function which is vport group manager but not eswitch manager such as
host PF on SmartNIC (BlueField) card. This will result in a kernel crash
when such a vport group manager is trying to access vports in its group.
E.g, PF vport manager (not eswitch manager) tries to configure the MAC
of its VF vport, a kernel trace will happen similar as bellow:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
...
RIP: 0010:mlx5_eswitch_get_vport_config+0xc/0x180 [mlx5_core]
...
Fixes: 5f5991f36d ("net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reported-by: Yuval Avnery <yuvalav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The IBM virtual ethernet driver's polling function continues
to process frames after rescheduling NAPI, resulting in a warning
if it exhausted its budget. Do not restart polling after calling
napi_reschedule. Instead let frames be processed in the following
instance.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Procedure mlx4_init_user_cqes() handles returns by copy_to_user
incorrectly. copy_to_user() returns the number of bytes not copied.
Thus, a non-zero return should be treated as a -EFAULT error
(as is done elsewhere in the kernel). However, mlx4_init_user_cqes()
error handling simply returns the number of bytes not copied
(instead of -EFAULT).
Note, though, that this is a harmless bug: procedure mlx4_alloc_cq()
(which is the only caller of mlx4_init_user_cqes()) treats any
non-zero return as an error, but that returned error value is processed
internally, and not passed further up the call stack.
In addition, fixes the following sparse warning:
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:1>*to
got void *buf
Fixes: e45678973d ("{net, IB}/mlx4: Initialize CQ buffers in the driver when possible")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver reads the query HCA capabilities without the corresponding masks.
Without the correct masks, the base addresses of the queues are
unaligned. In addition some reserved bits were wrongly read. Using the
correct masks, ensures alignment of the base addresses and allows future
firmware versions safe use of the reserved bits.
Fixes: ab9c17a009 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Fixes: 0ff1fb654b ("{NET, IB}/mlx4: Add device managed flow steering firmware API")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a bitmap to keep track of which partition types we've already seen;
for duplicates, return -EEXIST from efx_ef10_mtd_probe_partition() and
thus skip adding that partition.
Duplicate partitions occur because of the A/B backup scheme used by newer
sfc NICs. Prior to this patch they cause sysfs_warn_dup errors because
they have the same name, causing us not to expose any MTDs at all.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EtherAVB may provide a checksum of packet data appended to packet data. In
order to allow this checksum to be received by the host descriptor data
needs to be enlarged by 2 bytes to accommodate the checksum.
In the case of MTU-sized packets without a VLAN tag the
checksum were already accommodated by virtue of the space reserved for the
VLAN tag. However, a packet of MTU-size with a VLAN tag consumed all
packet data space provided by a descriptor leaving no space for the
trailing checksum.
This was not detected by the driver which incorrectly used the last two
bytes of packet data as the checksum and truncate the packet by two bytes.
This resulted all such packets being dropped.
A work around is to disable RX checksum offload
# ethtool -K eth0 rx off
This patch resolves this problem by increasing the size available for
packet data in RX descriptors by two bytes.
Tested on R-Car E3 (r8a77990) ES1.0 based Ebisu-4D board
v2
* Use sizeof(__sum16) directly rather than adding a driver-local
#define for the size of the checksum provided by the hw (2 bytes).
Fixes: 4d86d38186 ("ravb: RX checksum offload")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the device tree binding the phy-supply property is
optional. Use the regulator_get_optional API accordingly. The
code already handles NULL just fine.
This gets rid of the following warning:
fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The connect_local_phy should return NULL (not negative errno) on
error, since its caller expects it.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converted to use "imply" instead of "select" for PTP_1588_CLOCK
driver selecting. This could break the hard dependency between
the PTP clock subsystem and ethernet drivers.
This patch also set "default y" for dpaa2 ptp driver building to
provide user an available ptp clock in default.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initiating final cleanup after an ungraceful driver unload can lead to bad
PCI accesses towards the host.
This patch revises the load sequence so final cleanup is sent while the
internal master enable is cleared, to prevent the host accesses, and clears
the internal error indications just before enabling the internal master
enable.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent addition of SPDX license identifiers to the files in
drivers/net/ethernet/sun created a licensing conflict.
The cassini driver files contain a proper license notice:
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
but the SPDX change added:
SPDX-License-Identifier: GPL-2.0
So the file got tagged GPL v2 only while in fact it is licensed under GPL
v2 or later.
It's nice that people care about the SPDX tags, but they need to be more
careful about it. Not everything under (the) sun belongs to ...
Fix up the SPDX identifier and remove the boiler plate text as it is
redundant.
Fixes: c861ef83d7 ("sun: Add SPDX license tags to Sun network drivers")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Cc: Zhu Yanjun <yanjun.zhu@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcQmwjAAoJEEg/ir3gV/o+aBEIAIE8q3gEonMEPLnRoYSBlgUy
ZBl7/51yzC8CVdsdO7hx5dyyiI+gYq10Jp6TVpqA2i/V8P871T/u6+xRhP3T7dOc
Fq2YE70NdkCqFkpyc0QONzMC7ypwVqIEJrX7KnuLi5Ybsm9+tDia8AgC0NX/0H3U
bRgfzpupfK0TiLgtBe7kqC2WTo+bPzu0cEUu7xjQqUgZZie5QPyzW/6cEtn/V75+
A3btMNS5w0cfYK4mR4MMuc+UT4rSbsdyIZQrzICo75C2UnVMlojDf90+RuW4JFVw
tuOMA1LCB5l3lphgEEEerV2dZvs0ZJEuoYoFUkfgu2QEFSOMhod71t8/rurih0s=
=f23b
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-01-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-01-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.18
('net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames')
The patch doesn't apply cleanly to 4.18.y, but it is very simple to
resolve, what should be the procedure here ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the identifier used for indirect block callback registry
and for block rule cb registry (when done via indirect blocks) was the
pointer to the tunnel netdev we were interested in receiving updates on.
This worked fine if a single PF existed that registered one callback for
the tunnel netdev of interest. However, if multiple PFs are in place then
the 2nd PF tries to register with the same tunnel netdev identifier. This
leads to EEXIST errors and/or incorrect cb deletions.
Prevent this conflict by using the rpriv pointer as the identifier for
netdev indirect block cb registry, allowing each PF to register a unique
callback per tunnel netdev. For block cb registry, the same PF may
register multiple cbs to the same block if using TC shared blocks.
Instead of the rpriv, use the pointer to the allocated indr_priv data as
the identifier here. This means that there can be a unique block callback
for each PF/tunnel netdev combo.
Fixes: f5bc2c5de1 ("net/mlx5e: Support TC indirect block notifications
for eswitch uplink reprs")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For representors, the TX dropped counter is not folded from the
per-ring counters. Fix it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, we have a switch which pads non-zero octets, this
causes kernel hardware checksum fault repeatedly.
Prior to:
commit '88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")'
skb checksum was forced to be CHECKSUM_NONE when padding is detected.
After it, we need to keep skb->csum updated, like what we do for RXFCS.
However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP
headers, it is not worthy the effort as the packets are so small that
CHECKSUM_COMPLETE can't save anything.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The driver currently treats static FDB entries as both static and
sticky. This is incorrect and prevents such entries from being roamed to
a different port via learning.
Fix this by configuring static entries with ageing disabled and roaming
enabled.
In net-next we can add proper support for the newly introduced 'sticky'
flag.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a tc flower action of egress mirred redirect, the driver adds
an implicit FID setting action. This implicit action sets a dummy FID to
the packet and is used as part of a design for trapping unmatched flows
in OVS. While this implicit FID setting action is supposed to be a NOP
when a redirect action is added, in Spectrum-2 the FID record is
consulted as the dummy FID index is an 802.1D FID index and the packet
is dropped instead of being redirected.
Set the dummy FID index value to be within 802.1Q range. This satisfies
both Spectrum-1 which ignores the FID and Spectrum-2 which identifies it
as an 802.1Q FID and will then follow the redirect action.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return an appropriate error in the case when the driver timeouts on waiting
for firmware to go out of PCI reset.
Fixes: 233fa44bd6 ("mlxsw: pci: Implement reset done check")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum-2 PHY layer introduces a calibration period which is a part of the
Spectrum-2 firmware boot process. Hence increase the SW timeout waiting for
the firmware to come out of boot. This does not increase system boot time
in cases where the firmware PHY calibration process is done quickly.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet should be trapped to the CPU the device consumes a WQE
(work queue element) from an RDQ (receive descriptor queue) and copies
the packet to the address specified in the WQE. The device then tries to
post a CQE (completion queue element) that contains various metadata
(e.g., ingress port) about the packet to a CQ (completion queue).
In case the device managed to consume a WQE, but did not manage to post
the corresponding CQE, it will get stuck. This unlikely situation can be
triggered due to the scheme the driver is currently using to process
CQEs.
The driver will consume up to 512 CQEs at a time and after processing
each corresponding WQE it will ring the RDQ's doorbell, letting the
device know that a new WQE was posted for it to consume. Only after
processing all the CQEs (up to 512), the driver will ring the CQ's
doorbell, letting the device know that new ones can be posted.
Fix this by having the driver ring the CQ's doorbell for every processed
CQE, but before ringing the RDQ's doorbell. This guarantees that
whenever we post a new WQE, there is a corresponding CQE available. Copy
the currently processed CQE to prevent the device from overwriting it
with a new CQE after ringing the doorbell.
Note that the driver still arms the CQ only after processing all the
pending CQEs, so that interrupts for this CQ will only be delivered
after the driver finished its processing.
Before commit 8404f6f2e8 ("mlxsw: pci: Allow to use CQEs of version 1
and version 2") the issue was virtually impossible to trigger since the
number of CQEs was twice the number of WQEs and the number of CQEs
processed at a time was equal to the number of available WQEs.
Fixes: 8404f6f2e8 ("mlxsw: pci: Allow to use CQEs of version 1 and version 2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Semion Lisyansky <semionl@mellanox.com>
Tested-by: Semion Lisyansky <semionl@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XGBE hardware has support for performing MDIO operations using an
MDIO command request. The driver mistakenly uses the mdio port address
as the MDIO command request device address instead of the MDIO command
request port address. Additionally, the driver does not properly check
for and create a clause 45 MDIO command.
Check the supplied MDIO register to determine if the request is a clause
45 operation (MII_ADDR_C45). For a clause 45 operation, extract the device
address and register number from the supplied MDIO register and use them
to set the MDIO command request device address and register number fields.
For a clause 22 operation, the MDIO request device address is set to zero
and the MDIO command request register number is set to the supplied MDIO
register. In either case, the supplied MDIO port address is used as the
MDIO command request port address.
Fixes: 732f2ab7af ("amd-xgbe: Add support for MDIO attached PHYs")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As txq_trans_update() only updates trans_start when the lock is held,
trans_start does not get updated if NETIF_F_LLTX is declared.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 59361316af.
Due to problems found in additional testing, this causes an illegal
context switch in the RCU read-side critical section.
CC: Dave Jones <davej@codemonkey.org.uk>
CC: Cong Wang <xiyou.wangcong@gmail.com>
CC: Jan Jablonsky <jan.jablonsky@thalesgroup.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix regression in multi-SKB responses to RTM_GETADDR, from Arthur
Gautier.
2) Fix ipv6 frag parsing in openvswitch, from Yi-Hung Wei.
3) Unbounded recursion in ipv4 and ipv6 GUE tunnels, from Stefano
Brivio.
4) Use after free in hns driver, from Yonglong Liu.
5) icmp6_send() needs to handle the case of NULL skb, from Eric
Dumazet.
6) Missing rcu read lock in __inet6_bind() when operating on mapped
addresses, from David Ahern.
7) Memory leak in tipc-nl_compat_publ_dump(), from Gustavo A. R. Silva.
8) Fix PHY vs r8169 module loading ordering issues, from Heiner
Kallweit.
9) Fix bridge vlan memory leak, from Ido Schimmel.
10) Dev refcount leak in AF_PACKET, from Jason Gunthorpe.
11) Infoleak in ipv6_local_error(), flow label isn't completely
initialized. From Eric Dumazet.
12) Handle mv88e6390 errata, from Andrew Lunn.
13) Making vhost/vsock CID hashing consistent, from Zha Bin.
14) Fix lack of UMH cleanup when it unexpectedly exits, from Taehee Yoo.
15) Bridge forwarding must clear skb->tstamp, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
bnxt_en: Fix context memory allocation.
bnxt_en: Fix ring checking logic on 57500 chips.
mISDN: hfcsusb: Use struct_size() in kzalloc()
net: clear skb->tstamp in bridge forwarding path
net: bpfilter: disallow to remove bpfilter module while being used
net: bpfilter: restart bpfilter_umh when error occurred
net: bpfilter: use cleanup callback to release umh_info
umh: add exit routine for UMH process
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
vhost/vsock: fix vhost vsock cid hashing inconsistent
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
net: stmmac: Check if CBS is supported before configuring
net: stmmac: dwxgmac2: Only clear interrupts that are active
net: stmmac: Fix PCI module removal leak
tools/bpf: fix bpftool map dump with bitfields
tools/bpf: test btf bitfield with >=256 struct member offset
bpf: fix bpffs bitfield pretty print
net: ethernet: mediatek: fix warning in phy_start_aneg
tcp: change txhash on SYN-data timeout
...
When allocating memory pages for context memory, if the last page table
should be fully populated, the current code will set nr_pages to 0 when
calling bnxt_alloc_ctx_mem_blk(). This will cause the last page table
to be completely blank and causing some RDMA failures.
Fix it by setting the last page table's nr_pages to the remainder only
if it is non-zero.
Fixes: 08fe9d1816 ("bnxt_en: Add Level 2 context memory paging support.")
Reported-by: Eric Davis <eric.davis@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_hwrm_check_pf_rings(), add the proper flag to test the NQ
resources. Without the proper flag, the firmware will change
the NQ resource allocation and remap the IRQ, causing missing
IRQs. This issue shows up when adding MQPRIO TX queues, for example.
Fixes: 36d65be9a8 ("bnxt_en: Disable MSIX before re-reserving NQs/CMPL rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, TX is given a budget which is consumed by stmmac_tx_clean()
and stmmac_rx() is given the remaining non-consumed budget.
This is wrong and in case we are sending a large number of packets this
can starve RX because remaining budget will be low.
Let's give always the same budget for RX and TX clean.
While at it, check if we missed any interrupts while we were in NAPI
callback by looking at DMA interrupt status.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Watchdog can be disabled by platform definitions but currently we are
initializing the descriptors before checking if Watchdog must be
disabled or not.
Fix this by checking earlier if user wants Watchdog disabled or not.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if CBS is currently supported before trying to configure it in HW.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DMA interrupt handler we were clearing all interrupts status, even
the ones that were not active. Fix this and only clear the active
interrupts.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b7d0f08e91, the enable / disable of PCI device is not
managed which will result in IO regions not being automatically unmapped.
As regions continue mapped it is currently not possible to remove and
then probe again the PCI module of stmmac.
Fix this by manually unmapping regions on remove callback.
Changes from v1:
- Fix build error
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Fixes: b7d0f08e91 ("net: stmmac: Fix WoL for PCI-based setups")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
