Pablo Neira Ayuso says:
====================
* Remove limitation in the maximum number of supported sets in ipset.
Now ipset automagically increments the number of slots in the array
of sets by 64 new spare slots, from Jozsef Kadlecsik.
* Partially remove the generic queue infrastructure now that ip_queue
is gone. Its only client is nfnetlink_queue now, from Florian
Westphal.
* Add missing attribute policy checkings in ctnetlink, from Florian
Westphal.
* Automagically kill conntrack entries that use the wrong output
interface for the masquerading case in case of routing changes,
from Jozsef Kadlecsik.
* Two patches two improve ct object traceability. Now ct objects are
always placed in any of the existing lists. This allows us to dump
the content of unconfirmed and dying conntracks via ctnetlink as
a way to provide more instrumentation in case you suspect leaks,
from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In 5GHz/802.11a, we are allowed to use short slot times. Doing this
may increases performance by 20% for legacy connections (54 MBit/s).
I can confirm this in my tests (27% more throughput using iperf), and
also have a small positive effect (5% more throughput) for HT rates,
tested on 1 stream.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I believe this commit from 2008 was incorrect:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=398bcbebb6f721ac308df1e3d658c0029bb74503
When CONFIG_IPV6_ROUTER_PREF is disabled, the kernel should follow
RFC4861 section 6.3.6: if no route is NUD_VALID, then traffic should be
sprayed across all routers (indirectly triggering NUD) until one of them
becomes NUD_VALID.
However, the following experiment demonstrates that this does not work:
1) Connect to an IPv6 network.
2) Change the router's MAC (and link-local) address.
The kernel will lock onto the first router and never try the new one, even
if the first becomes unreachable. This patch fixes the problem by
allowing rt6_check_neigh() to return 0; if all routers return 0, then
rt6_select() will fall back to round-robin behavior.
This patch should have no effect when CONFIG_IPV6_ROUTER_PREF=y.
Note that rt6_check_neigh() is only used in a boolean context, so I've
changed its return type accordingly.
Signed-off-by: Paul Marks <pmarks@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of 026359b [ipv6: Send ICMPv6 RSes only when RAs are accepted],
Router Solicitations are sent whenever kernel accepts Router
Advertisements on the interface.
However, this logic isn't reflected in 'addrconf_rs_timer'.
The timer fails to issue subsequent RS messages (and fails to re-arm
itself) if forwarding is enabled and the special hybrid mode is
enabled (accept_ra=2).
Fix the condition determining whether next RS should be sent, by using
'ipv6_accept_ra()'.
Reported-by: Ami Koren <amikoren@yahoo.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current SCTP stack is lacking a mechanism to have per association
statistics. This is an implementation modeled after OpenSolaris'
SCTP_GET_ASSOC_STATS.
Userspace part will follow on lksctp if/when there is a general ACK on
this.
V4:
- Move ipackets++ before q->immediate.func() for consistency reasons
- Move sctp_max_rto() at the end of sctp_transport_update_rto() to avoid
returning bogus RTO values
- return asoc->rto_min when max_obs_rto value has not changed
V3:
- Increase ictrlchunks in sctp_assoc_bh_rcv() as well
- Move ipackets++ to sctp_inq_push()
- return 0 when no rto updates took place since the last call
V2:
- Implement partial retrieval of stat struct to cope for future expansion
- Kill the rtxpackets counter as it cannot be precise anyway
- Rename outseqtsns to outofseqtsns to make it clearer that these are out
of sequence unexpected TSNs
- Move asoc->ipackets++ under a lock to avoid potential miscounts
- Fold asoc->opackets++ into the already existing asoc check
- Kill unneeded (q->asoc) test when increasing rtxchunks
- Do not count octrlchunks if sending failed (SCTP_XMIT_OK != 0)
- Don't count SHUTDOWNs as SACKs
- Move SCTP_GET_ASSOC_STATS to the private space API
- Adjust the len check in sctp_getsockopt_assoc_stats() to allow for
future struct growth
- Move association statistics in their own struct
- Update idupchunks when we send a SACK with dup TSNs
- return min_rto in max_rto when RTO has not changed. Also return the
transport when max_rto last changed.
Signed-off: Michele Baldessari <michele@acksyn.org>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make code more readable by changing CONF_NO_FCS_RECV which is read
as "No L2CAP FCS option received" to CONF_RECV_NO_FCS which means
"Received L2CAP option NO_FCS". This flag really means that we have
received L2CAP FRAME CHECK SEQUENCE (FCS) OPTION with value "No FCS".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
If L2CAP_FEAT_FCS is not supported we sould miss EWS option
configuration because of break. Make code more readable by
combining FCS configuration in the single block.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Before starting quering remote AMP controllers make sure
that there is local active AMP controller.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
After getting HCIDEVDOWN controller did not mark itself as 0x00 which
means: "The Controller radio is available but is currently physically
powered down". The result was even if the hdev was down we return
in controller list value 0x01 "status 0x01 (Bluetooth only)".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
l2cap_send_disconn_req takes 3 parameters of which conn might be
derived from chan. Make this conversion inside l2cap_send_disconn_req.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Some comparisons needs to double negation(!!) in order to make the value
of the field boolean. Add it to the macro makes the code more readable.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
In order to authenticate and configure an incoming SCO connection, the
BT_DEFER_SETUP option was added. This option is intended to defer reply
to Connect Request on SCO sockets.
When a connection is requested, the listening socket is unblocked but
the effective connection setup happens only on first recv. Any send
between accept and recv fails with -ENOTCONN.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This option will set the BT_SK_DEFER_SETUP bit in socket flags.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
When the route changes (backup default route, VPNs) which affect a
masqueraded target, the packets were sent out with the outdated source
address. The patch addresses the issue by comparing the outgoing interface
directly with the masqueraded interface in the nat table.
Events are inefficient in this case, because it'd require adding route
events to the network core and then scanning the whole conntrack table
and re-checking the route for all entry.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add stricter checking for a few attributes.
Note that these changes don't fix any bug in the current code base.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We used to have several queueing backends, but nowadays only
nfnetlink_queue remains.
In light of this there doesn't seem to be a good reason to
support per-af registering -- just hook up nfnetlink_queue on module
load and remove it on unload.
This means that the userspace BIND/UNBIND_PF commands are now obsolete;
the kernel will ignore them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new operation to dump the content of the dying and
unconfirmed lists.
Under some situations, the global conntrack counter can be inconsistent
with the number of entries that we can dump from the conntrack table.
The way to resolve this is to allow dumping the content of the unconfirmed
and dying lists, so far it was not possible to look at its content.
This provides some extra instrumentation to resolve problematic situations
in which anyone suspects memory leaks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch modifies the conntrack subsystem so that all existing
allocated conntrack objects can be found in any of the following
places:
* the hash table, this is the typical place for alive conntrack objects.
* the unconfirmed list, this is the place for newly created conntrack objects
that are still traversing the stack.
* the dying list, this is where you can find conntrack objects that are dying
or that should die anytime soon (eg. once the destroy event is delivered to
the conntrackd daemon).
Thus, we make sure that we follow the track for all existing conntrack
objects. This patch, together with some extension of the ctnetlink interface
to dump the content of the dying and unconfirmed lists, will help in case
to debug suspected nf_conn object leaks.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The max number of sets was hardcoded at kernel cofiguration time and
could only be modified via a module parameter. The patch adds the support
of increasing the max number of sets automatically, as needed.
The array of sets is incremented by 64 new slots if we run out of
empty slots. The absolute limit for the maximal number of sets
is limited by 65534.
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix an error on mesh join when no channel has been
explicitly set beforehand.
Also remove a double semicolon.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If channel contexts are enabled, the CSA should not be processed
further. A return is missing here.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TCP coalescing added a regression in splice(socket->pipe) performance,
for some workloads because of the way tcp_read_sock() is implemented.
The reason for this is the break when (offset + 1 != skb->len).
As we released the socket lock, this condition is possible if TCP stack
added a fragment to the skb, which can happen with TCP coalescing.
So let's go back to the beginning of the loop when this happens,
to give a chance to splice more frags per system call.
Doing so fixes the issue and makes GRO 10% faster than LRO
on CPU-bound splice() workloads instead of the opposite.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Woodhouse says:
====================
This is the result of pulling on the thread started by Krzysztof Mazur's
original patch 'pppoatm: don't send frames to destroyed vcc'.
Various problems in the pppoatm and br2684 code are solved, some of which
were easily triggered and would panic the kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent network changes allowed high order pages being used
for skb fragments.
This uncovered a bug in do_tcp_sendpages() which was assuming its caller
provided an array of order-0 page pointers.
We only have to deal with a single page in this function, and its order
is irrelevant.
Reported-by: Willy Tarreau <w@1wt.eu>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need to schedule the wakeup tasklet on *every* unlock; only if we
actually blocked the channel in the first place.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>
The br2684 does not check if used vcc is in connected state,
causing potential Oops in pppoatm_send() when vcc->send() is called
on not fully connected socket.
Now br2684 can be assigned only on connected sockets; otherwise
-EINVAL error is returned.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The br2684 code used module_put() during unassignment from vcc with
hope that we have BKL. This assumption is no longer true.
Now owner field in atmvcc is used to move this module_put()
to vcc_destroy_socket().
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>
Now that we can return zero from pppoatm_send() for reasons *other* than
the queue being full, that means we can't depend on a subsequent call to
pppoatm_pop() waking the queue, and we might leave it stalled
indefinitely.
Use the ->release_cb() callback to wake the queue after the sock is
unlocked.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>
Avoid submitting packets to a vcc which is being closed. Things go badly
wrong when the ->pop method gets later called after everything's been
torn down.
Use the ATM socket lock for synchronisation with vcc_destroy_socket(),
which clears the ATM_VF_READY bit under the same lock. Otherwise, we
could end up submitting a packet to the device driver even after its
->ops->close method has been called. And it could call the vcc's ->pop
method after the protocol has been shut down. Which leads to a panic.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>
The immediate use case for this is that it will allow us to ensure that a
pppoatm queue is woken after it has to drop a packet due to the sock being
locked.
Note that 'release_cb' is called when the socket is *unlocked*. This is
not to be confused with vcc_release() — which probably ought to be called
vcc_close().
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Krzysztof Mazur <krzysiek@podlesie.net>
As of 026359b [ipv6: Send ICMPv6 RSes only when RAs are accepted], the
logic determining whether to send Router Solicitations is identical
to the logic determining whether kernel accepts Router Advertisements.
However the condition itself is repeated in several code locations.
Unify it by introducing 'ipv6_accept_ra()' accessor.
Also, simplify the condition expression, making it more readable.
No semantic change.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As time passed, available memory increased faster than number of
concurrent tcp sockets.
As a result, a machine with 4GB of ram gets a hash table
with 524288 slots, using 8388608 bytes of memory.
Lets change that by a 16x factor (one slot for 128 KB of ram)
Even if a small machine needs a _lot_ of sockets, tcp lookups are now
very efficient, using one cache line per socket.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 68835aba4d (net: optimize INET input path further)
moved some fields used for tcp/udp sockets lookup in the first cache
line of struct sock_common.
This patch moves inet_dport/inet_num as well, filling a 32bit hole
on 64 bit arches and reducing number of cache line misses in lookups.
Also change INET_MATCH()/INET_TW_MATCH() to perform the ports match
before addresses match, as this check is more discriminant.
Remove the hash check from MATCH() macros because we dont need to
re validate the hash value after taking a refcount on socket, and
use likely/unlikely compiler hints, as the sk_hash/hash check
makes the following conditional tests 100% predicted by cpu.
Introduce skc_addrpair/skc_portpair pair values to better
document the alignment requirements of the port/addr pairs
used in the various MATCH() macros, and remove some casts.
The namespace check can also be done at last.
This slightly improves TCP/UDP lookup times.
IP/TCP early demux needs inet->rx_dst_ifindex and
TCP needs inet->min_ttl, lets group them together in same cache line.
With help from Ben Hutchings & Joe Perches.
Idea of this patch came after Ling Ma proposal to move skc_hash
to the beginning of struct sock_common, and should allow him
to submit a final version of his patch. My tests show an improvement
doing so.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Joe Perches <joe@perches.com>
Cc: Ling Ma <ling.ma.program@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the variable parameter length provided in the mandatory
heartbeat information parameter exceeds the calculated payload
length the packet has been corrupted. Reply with a parameter
length protocol violation message.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes an unused parameter (src_net) from rtnl_create_link()
method and from the method single invocation, in veth.
This parameter was used in the past when calling
ops->get_tx_queues(src_net, tb) in rtnl_create_link().
The get_tx_queues() member of rtnl_link_ops was replaced by two methods,
get_num_tx_queues() and get_num_rx_queues(), which do not get any
parameter. This was done in commit d40156aa5e by
Jiri Pirko ("rtnl: allow to specify different num for rx and tx queue count").
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the new ETH_P_BATMAN define instead of the private BATADV_ETH_P_BATMAN
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=hrO7
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- Use the new ETH_P_BATMAN define instead of the private BATADV_ETH_P_BATMAN
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree_skb() indicates failure, which is where this is being used.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
kfree_skb() was not getting called in the case of some failures.
This was pointed out by Eric Dumazet.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the threshold for framentation of a lowpan packet from
using the MTU size to now use the MTU size minus the checksum length,
which is added by the hardware. For IEEE 802.15.4, this effectively
changes it from 127 bytes to 125 bytes.
Signed-off-by: Alan Ott <alan@signal11.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug is observed on running FCoE over a VLAN device associated w/
a real device that has IFF_UNICAST_FLT set since FCoE would add unicast
address such as FLOGI MAC to the VLAN interface that FCoE is on. Since
currently, VLAN device is not inheriting the IFF_UNICAST_FLT flag from the
parent real device even though the real device is capable of doing unicast
filtering. This forces the VLAN device and its real device go to promiscuous
mode unnecessarily even the added address is actually being added to the
available unicast filter table in real device.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: devel@open-fcoe.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/exthdrs_core.c
Jesse Gross says:
====================
This series of improvements for 3.8/net-next contains four components:
* Support for modifying IPv6 headers
* Support for matching and setting skb->mark for better integration with
things like iptables
* Ability to recognize the EtherType for RARP packets
* Two small performance enhancements
The movement of ipv6_find_hdr() into exthdrs_core.c causes two small merge
conflicts. I left it as is but can do the merge if you want. The conflicts
are:
* ipv6_find_hdr() and ipv6_find_tlv() were both moved to the bottom of
exthdrs_core.c. Both should stay.
* A new use of ipv6_find_hdr() was added to net/netfilter/ipvs/ip_vs_core.c
after this patch. The IPVS user has two instances of the old constant
name IP6T_FH_F_FRAG which has been renamed to IP6_FH_F_FRAG.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.
Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of assuming 200 bytes are always enough for
all the IEs we add, give the length of the buffer
to the function and warn instead of overrunning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cmp_bss() comparator function uses memcmp() to
compare the SSID. This means that cmp_hidden_bss()
needs to similarly return a number bigger than zero
(use 1) instead of -1 when ie1 is bigger than ie2,
which is the case if an ie2 byte is non-zero.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to stop the machine, just leak
the BSS entry if there's an issue with its hold
counter when freeing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This change allows userspace to register for probe request
frames on an IBSS interface. Userspace then has to handle
them and send replies.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pppoatm_may_send() is quite heavy and it's called three times
in pppoatm_send() and inlining costs more than 200 bytes of code
(more than 10% of total pppoatm driver code size).
add/remove: 1/0 grow/shrink: 0/1 up/down: 132/-367 (-235)
function old new delta
pppoatm_may_send - 132 +132
pppoatm_send 900 533 -367
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The vcc_destroy_socket() closes vcc before the protocol is detached
from vcc by calling vcc->push() with NULL skb. This leaves some time
window, where the protocol may call vcc->send() on closed vcc
and crash.
Now pppoatm_send(), like vcc_sendmsg(), checks for vcc flags that
indicate that vcc is not ready. If the vcc is not ready we just
drop frame. Queueing frames is much more complicated because we
don't have callbacks that inform us about vcc flags changes.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently the mesh sync code checks, whether peers indicate TBTT adjustment,
but it never sets the corresponding flag itself.
By setting ifmsh->tbtt_adjusting to true, it will set the corresponding field
in the mesh configuration IE of own beacons.
This indication will be set in the current beacon. The TBTT adjustment will be
performed afterwards, affecting the next beacon. Thus, the first beacon with
stable TBTT will not indicate adjustment anymore and peers will continue
tracking the new offset.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ETH_P_BATMAN ethertype is now defined kernel-wide. Use it instead
of the private BATADV_ETH_P_BATMAN define.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
This patch changes three methods to be static and removes their
EXPORT_SYMBOLs in core/dev.c and their external declaration in
netdevice.h. The methods, dev_gro_receive(), napi_frags_finish() and
napi_skb_finish(), which are in the GRO rx path, are not used
outside core/dev.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a standalone if, seems to be a regression of commit
"nl80211/cfg80211: add VHT MCS support".
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a debugfs file showing the rate at which
the last packet is received.
Signed-off-by: Saravana <saravanad@posedge.com>
[fix whitespace]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the logic to fill a struct rate_info with
a STA's last RX rate is accessible only in the cfg.c.
As the RX rate calculation might be needed elsewhere,
split this out into a separate function.
Signed-off-by: Saravana <saravanad@posedge.com>
[fix various whitespace issues, reword commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a debugfs file showing the current tx rate.
The information available in the rc_stats file
doesn't evidently provides us the current tx rate.
This patch adds the support for the same.
Signed-off-by: Saravana <saravanad@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a debugfs file showing the signal strength
of the ack frame that is received for the
currently sent tx packet
Signed-off-by: Saravana <saravanad@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
This pull request is intended for the 3.8 stream. It is a bit large
-- I guess Thanksgiving got me off track! At least the code got to
spend some time in linux-next... :-)
This includes the usual batch of pulls for Bluetooth, NFC, and mac80211
as well as iwlwifi. Also here is an ath6kl pull, and a new driver
in the rtlwifi family. The brcmfmac, brcmsmac, ath9k, and mwl8k get
their usual levels of attention, and a handful of other updates tag
along as well.
For more detail on the pulls, please see below...
On Bluetooth, Gustavo says:
"Another set of patches for integration in wireless-next. There are two big set
of changes in it: Andrei Emeltchenko and Mat Martineau added more patches
towards a full Bluetooth High Speed support and Johan Hedberg improve the
single mode support for Bluetooth dongles. Apart from that we have small fixes
and improvements."
...and:
"A few patches to 3.8. The majority of the work here is from Andrei on the High
Speed support. Other than that Johan added support for setting LE advertising
data. The rest are fixes and clean ups and small improvements like support for
a new broadcom hardware."
On mac80211, Johannes says:
"This is for mac80211, for -next (3.8). Plenty of changes, as you can see
below. Some fixes for previous changes like the export.h include, the
beacon listener fix from Ben Greear, etc. Overall, no exciting new
features, though hwsim does gain channel context support for people to
try it out and look at."
...and...:
"This one contains the mac80211-next material. Apart from a few small new
features and cleanups I have two fixes for the channel context code. The
RX_END timestamp support will probably be reworked again as Simon Barber
noted the calculations weren't really valid, but the discussions there
are still going on and it's better than what we had before."
...and:
"Please pull (see below) to get the following changes:
* a fix & a debug aid in IBSS from Antonio,
* mesh cleanups from Marco,
* a few bugfixes for some of my previous patches from Arend and myself,
* and the big initial VHT support patchset"
And on iwlwifi, Johannes says:
"In addition to the previous four patches that I'm not resending,
we have a number of cleanups, message reduction, firmware error
handling improvements (yes yes... we need to fix them instead)
and various other small things all over."
...and:
"In his quest to try to understand the current iwlwifi problems (like
stuck queues etc.) Emmanuel has first cleaned up the PCIe code, I'm
including his changes in this pull request. Other than that I only have
a small cleanup from Sachin Kamat to remove a duplicate include and a
bugfix to turn off MFP if software crypto is enabled, but this isn't
really interesting as MFP isn't supported right now anyway."
On NFC, Samuel says:
"With this one we have:
- A few HCI improvements in preparation for an upcoming HCI chipset support.
- A pn544 code cleanup after the old driver was removed.
- An LLCP improvement for notifying user space when one peer stops ACKing I
frames."
On ath6kl, Kalle says:
"Major changes this time are firmware recover support to gracefully
handle if firmware crashes, support for changing regulatory domain and
support for new ar6004 hardware revision 1.4. Otherwise there are just
smaller fixes or cleanups from different people."
Thats about it... :-) Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, each time a device is detached from an OVS datapath
we call synchronize RCU before freeing associated data structures.
However, if a bridge is deleted (which detaches all ports) when
many devices are connected then there can be a long delay. This
switches to use call_rcu() to group the cost together.
Reported-by: Justin Pettit <jpettit@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
nfc_llcp_ns(s) dereferences the s pointer which is freed a line
above. In a result, it can produce a crash or you will read
incorrect value.
Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch reports the change made by Stephen Hemminger in ipip and gre[6] in
commit eccc1bb8d4 (tunnel: drop packet if ECN present with not-ECT).
Goal is to handle RFC6040, Section 4.2:
Default Tunnel Egress Behaviour.
o If the inner ECN field is Not-ECT, the decapsulator MUST NOT
propagate any other ECN codepoint onwards. This is because the
inner Not-ECT marking is set by transports that rely on dropped
packets as an indication of congestion and would not understand or
respond to any other ECN codepoint [RFC4774]. Specifically:
* If the inner ECN field is Not-ECT and the outer ECN field is
CE, the decapsulator MUST drop the packet.
* If the inner ECN field is Not-ECT and the outer ECN field is
Not-ECT, ECT(0), or ECT(1), the decapsulator MUST forward the
outgoing packet with the ECN field cleared to Not-ECT.
The patch takes benefits from common function added in net/inet_ecn.h.
Like it was done for Xin4 tunnels, it adds logging to allow detecting broken
systems that set ECN bits incorrectly when tunneling (or an intermediate
router might be changing the header). Errors are also tracked via
rx_frame_error.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the memory we allocated earlier in irttp_open_tsap() when we hit
this error path. The leak goes back to at least 1da177e4
("Linux-2.6.12-rc2").
Discovered with Trinity (the syscall fuzzer).
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch turns QFQ into QFQ+, a variant of QFQ that provides the
following two benefits: 1) QFQ+ is faster than QFQ, 2) differently
from QFQ, QFQ+ correctly schedules also non-leaves classes in a
hierarchical setting. A detailed description of QFQ+, plus a
performance comparison with DRR and QFQ, can be found in [1].
[1] P. Valente, "Reducing the Execution Time of Fair-Queueing Schedulers"
http://algo.ing.unimo.it/people/paolo/agg-sched/agg-sched.pdf
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calculation of RTTVAR involves the subtraction of two unsigned
numbers which
may causes rollover and results in very high values of RTTVAR when RTT > SRTT.
With this patch it is possible to set RTOmin = 1 to get the minimum of RTO at
4 times the clock granularity.
Change Notes:
v2)
*Replaced abs() by abs64() and long by __s64, changed patch
description.
Signed-off-by: Christian Schoch <e0326715@student.tuwien.ac.at>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Sridhar Samudrala <sri@us.ibm.com>
CC: Neil Horman <nhorman@tuxdriver.com>
CC: linux-sctp@vger.kernel.org
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following program, that sets the second argument to the
sendto() syscall incorrectly:
#include <string.h>
#include <arpa/inet.h>
#include <sys/socket.h>
int main(void)
{
int fd;
struct sockaddr_in sa;
fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/);
if (fd < 0)
return 1;
memset(&sa, 0, sizeof(sa));
sa.sin_family = AF_INET;
sa.sin_addr.s_addr = inet_addr("127.0.0.1");
sa.sin_port = htons(11111);
sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa));
return 0;
}
We get -ENOMEM:
$ strace -e sendto ./demo
sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 ENOMEM (Cannot allocate memory)
Propagate the error code from sctp_user_addto_chunk(), so that we will
tell user space what actually went wrong:
$ strace -e sendto ./demo
sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 EFAULT (Bad address)
Noticed while running Trinity (the syscall fuzzer).
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trinity (the syscall fuzzer) discovered a memory leak in SCTP,
reproducible e.g. with the sendto() syscall by passing invalid
user space pointer in the second argument:
#include <string.h>
#include <arpa/inet.h>
#include <sys/socket.h>
int main(void)
{
int fd;
struct sockaddr_in sa;
fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/);
if (fd < 0)
return 1;
memset(&sa, 0, sizeof(sa));
sa.sin_family = AF_INET;
sa.sin_addr.s_addr = inet_addr("127.0.0.1");
sa.sin_port = htons(11111);
sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa));
return 0;
}
As far as I can tell, the leak has been around since ~2003.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes some unintended resets of the rate control statistics
when minstrel_ht is used resulting in non-optimal throughput on mesh
links.
Tested-by: Emanuel Taube <emanuel.taube@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a driver registers an address mask we should ensure that no
interface gets an address assigned that isn't covered by the
registered address mask. This prevents invalid configurations
from reaching the device and causing problems.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
[change function flow to reduce indentation, fix locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Smatch complains that we could dereference skb later in the function.
It's probably unlikely, but we may as well return here and avoid it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[change summary]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The CQM TX-error rate/interval can't be less than
zero since they're unsigned values, remove checks.
Also fix indentation of the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The pppoatm_send() does not take any lock that will prevent concurrent
vcc_sendmsg(). This causes two problems:
- there is no locking between checking the send queue size
with atm_may_send() and incrementing sk_wmem_alloc,
and the real queue size can be a little higher than sk_sndbuf
- the vcc->sendmsg() can be called concurrently. I'm not sure
if it's allowed. Some drivers (eni, nicstar, ...) seem
to assume it will never happen.
Now pppoatm_send() takes ATM socket lock, the same that is used
in vcc_sendmsg() and other ATM socket functions. The pppoatm_send()
is called with BH disabled, so bh_lock_sock() is used instead
of lock_sock().
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The pppoatm used module_put() during unassignment from vcc with
hope that we have BKL. This assumption is no longer true.
Now owner field in atmvcc is used to move this module_put()
to vcc_destroy_socket().
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The pppoatm does not check if used vcc is in connected state,
causing an Oops in pppoatm_send() when vcc->send() is called
on not fully connected socket.
Now pppoatm can be assigned only on connected sockets; otherwise
-EINVAL error is returned.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The atm is using atmvcc->push(vcc, NULL) callback to notify protocol
that vcc will be closed and protocol must detach from it. This callback
is usually used by protocol to decrement module usage count by module_put(),
but it leaves small window then module is still used after module_put().
Now the owner of push() callback is kept in atmvcc and
module_put(atmvcc->owner) is called after the protocol is detached from vcc.
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
If the low-level driver wants to support P2P GO
powersave configuration, it must set the cfg80211
flags and mac80211 will pass the parameters to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a driver supports P2P GO powersave, allow it to
set the new feature flags for it and allow userspace
to configure the parameters for it. This can be done
at GO startup and later changed with SET_BSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add some information that we have about VHT to radiotap.
This at least lets one see the MCS and NSS information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Determine the VHT channel from the AP's VHT operation IE
(if present) and configure the hardware to that channel
if it is supported. If channel contexts cause a channel
to not be usable, try a smaller bandwidth.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some of the chandef checking that we do in cfg80211
to check if a channel is supported or not is also
needed in mac80211, so rework that a bit and export
the functions that are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Name of pimreg devices are built from following format :
char name[IFNAMSIZ]; // IFNAMSIZ == 16
sprintf(name, "pimreg%u", mrt->id);
We must therefore limit mrt->id to 9 decimal digits
or risk a buffer overflow and a crash.
Restrict table identifiers in [0 ... 999999999] interval.
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_getpeer_v4() can return NULL under OOM conditions, and while
inet_peer_xrlim_allow() is OK with a NULL peer, inet_putpeer() will
crash.
This code path now uses the same idiom as the others from:
1d861aa4b3 ("inet: Minimize use of
cached route inetpeer.").
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having the getsockopt() of SO_BINDTODEVICE return an index, which
will then require another call like if_indextoname() to get the actual interface
name, have it return the name directly.
This also matches the existing man page description on socket(7) which mentions
the argument being an interface name.
If the value has not been set, zero is returned and optlen will be set to zero
to indicate there is no interface name present.
Added a seqlock to protect this code path, and dev_ifname(), from someone
changing the device name via dev_change_name().
v2: Added seqlock protection while copying device name.
v3: Fixed word wrap in patch.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's really no excuse for an additional wmem_default of buffering
between the netdev queue and the ATM device. Two packets (one in-flight,
and one ready to send) ought to be fine. It's not as if it should take
long to get another from the netdev queue when we need it.
If necessary we can make the queue space configurable later, but I don't
think it's likely to be necessary.
cf. commit 9d02daf754 (pppoatm: Fix
excessive queue bloat) which did something very similar for PPPoATM.
Note that there is a tremendously unlikely race condition which may
result in qspace temporarily going negative. If a CPU running the
br2684_pop() function goes off into the weeds for a long period of time
after incrementing qspace to 1, but before calling netdev_wake_queue()...
and another CPU ends up calling br2684_start_xmit() and *stopping* the
queue again before the first CPU comes back, the netdev queue could
end up being woken when qspace has already reached zero.
An alternative approach to coping with this race would be to check in
br2684_start_xmit() for qspace==0 and return NETDEV_TX_BUSY, but just
using '> 0' and '< 1' for comparison instead of '== 0' and '!= 0' is
simpler. It just warranted a mention of *why* we do it that way...
Move the call to atmvcc->send() to happen *after* the accounting and
potentially stopping the netdev queue, in br2684_xmit_vcc(). This matters
if the ->send() call suffers an immediate failure, because it'll call
br2684_pop() with the offending skb before returning. We want that to
happen *after* we've done the initial accounting for the packet in
question. Also make it return an appropriate success/failure indication
while we're at it.
Tested by running 'ping -l 1000 bottomless.aaisp.net.uk' from within my
network, with only a single PPPoE-over-BR2684 link running. And after
setting txqueuelen on the nas0 interface to something low (5, in fact).
Before the patch, we'd see about 15 packets being queued and a resulting
latency of ~56ms being reached. After the patch, we see only about 8,
which is fairly much what we expect. And a max latency of ~36ms. On this
OpenWRT box, wmem_default is 163840.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Reviewed-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 82167cb8c6 ('net: dsa/slave: Fix
compilation warnings') fixed one possible invalid configuration
(NET_DSA enabled with no trailer formats) but added others: drivers
can select NET_DSA without its dependencies being met.
It's not very useful to make either the DSA core or the tagging
formats manually selectable without a driver to use them, so:
1. Define a hidden HAVE_NET_DSA option and move the dependencies of
NET_DSA to that. While we're at it, drop the deprecated
EXPERIMENTAL dependency.
2. Make NET_DSA and the drivers dependent on HAVE_NET_DSA.
3. Hide the tagging format options again.
4. Make drivers select both NET_DSA and the appropriate tagging format
option.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set in the rx_ifindex to pass the correct interface index in the case of a
message timeout detection. Usually the rx_ifindex value is set at receive
time. But when no CAN frame has been received the RX_TIMEOUT notification
did not contain a valid value.
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Andre Naujoks <nautsch2@googlemail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Felix Liao reported that when an interface is set DOWN
while another interface is executing a ROC, the warning
in ieee80211_start_next_roc() (about the first item on
the list having started already) triggers.
This is because ieee80211_roc_purge() calls it even if
it never actually changed the list of ROC items. To fix
this, simply remove the function call. If it is needed
then it will be done by the ieee80211_sw_roc_work()
function when the ROC item that is being removed while
active is cleaned up.
Cc: stable@vger.kernel.org
Reported-by: Felix Liao <Felix.Liao@watchguard.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for skb mark matching and set action.
Signed-off-by: Ansis Atteka <aatteka@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
In some cases, e.g. probe_status, there were spaces
missing so the trace output was confusing. Also make
it more like mac80211 when printing netdevs/wiphys
to make reading a combined log easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for reporting and calculating VHT MCSes.
Note that I'm not completely sure that the bitrate
calculations are correct, nor that they can't be
simplified.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.
Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)
This also adds new helper functions:
- cfg80211_chandef_create to create a channel def
struct given the control channel and channel type,
- cfg80211_chandef_identical to check if two channel
definitions are identical
- cfg80211_chandef_compatible to check if the given
channel definitions are compatible, and return the
wider of the two
This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
- regulatory checks on the usable bandwidth (if that
even makes sense)
- regulatory TX power (database can't deal with it)
- a proper channel compatibility calculation for the
new channel types
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.
Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If ieee80211_prep_channel() decides that HT should be
disabled (because the HT IEs from the AP were invalid)
it will set the IEEE80211_STA_DISABLE_HT to not send
HT capabilities to the AP when associating. If this
happens during authentication, the flag will be lost
and we send HT frames, even if the channel config was
set up for non-HT. This can lead to issues.
Fix this by always resetting the ifmgd flags to zero
when the channel context is released so that the flag
resetting in ieee80211_mgd_assoc() isn't necessary.
To make the code a bit easier move the call to release
the channel in ieee80211_set_disassoc() to the end of
the function together with the flag resetting (which
needs to be at the end to avoid timers setting flags.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use shortcut pointer instead where it is appropriate.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Return early if not a QoS Data frame.
Give proper documentation.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The debug message has to be printed also for an Auth message with
auth_sequence != 1. This helps understanding whether the two Auth
messages are exchanged correctly or not.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It does not make sense to keep a station alive if it is not authorised
at all. If IBSS/RSN is used it could also be the case that something
went wrong during the keys exchange and the stations ended up in a not
recoverable state.
By not updating last_rx we are giving the station a chance to be
deleted and to start the key exchange once again from scratch.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function cfg80211_get_p2p_attr() can fail and returns
a negative error code. However, the return type is unsigned
int. The largest positive number is determined by desired_len
variable in the function, which is u16. So changing the return
type to int to allow easy error checking. Also change the type
for the attribute to enum for improved type checking.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[fix indentation, don't use u8 attr variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Save a few bytes per table by convert mroute_do_assert and
mroute_do_pim from int to bool.
Remove !! as the compiler does that when assigning int to bool.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) ip_mroute_setsockopt() & ip_mroute_getsockopt() should not
access/set raw_sk(sk)->ipmr_table before making sure the socket
is a raw socket, and protocol is IGMP
2) MRT_INIT should return -EINVAL if optlen != sizeof(int), not
-ENOPROTOOPT
3) MRT_ASSERT & MRT_PIM should validate optlen
4) " (v) ? 1 : 0 " can be written as " !!v "
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when none of CONFIG_NET_DSA_TAG_DSA, CONFIG_NET_DSA_TAG_EDSA and
CONFIG_NET_DSA_TAG_TRAILER is defined, we get following compilation warnings:
net/dsa/slave.c:51:12: warning: 'dsa_slave_init' defined but not used [-Wunused-function]
net/dsa/slave.c:60:12: warning: 'dsa_slave_open' defined but not used [-Wunused-function]
net/dsa/slave.c:98:12: warning: 'dsa_slave_close' defined but not used [-Wunused-function]
net/dsa/slave.c:116:13: warning: 'dsa_slave_change_rx_flags' defined but not used [-Wunused-function]
net/dsa/slave.c:127:13: warning: 'dsa_slave_set_rx_mode' defined but not used [-Wunused-function]
net/dsa/slave.c:136:12: warning: 'dsa_slave_set_mac_address' defined but not used [-Wunused-function]
net/dsa/slave.c:164:12: warning: 'dsa_slave_ioctl' defined but not used [-Wunused-function]
Earlier approach to fix this was discussed here:
lkml.org/lkml/2012/10/29/549
This is another approach to fix it. This is done by some changes in config
options, which make more sense than the earlier approach. As, atleast one
tagging option must always be selected for using net/dsa/ infrastructure, this
patch selects NET_DSA from tagging configs instead of having it as an selectable
config.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it possible to build the CAN Identifier into the kernel, even
if the CAN support is build as a module.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
attribute is copied to IFNAMSIZ-size stack variable,
but IFNAMSIZ is smaller than IPSET_MAXNAMELEN.
Fortunately nfnetlink needs CAP_NET_ADMIN.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Paul Gortmaker says:
====================
The most interesting thing here, at least from a user perspective,
is the broadcast link fix -- where there was a corner case where
two endpoints could get in a state where they disagree on where
to start Rx and ack of broadcast packets.
There is also the poll/wait changes which could also impact
end users for certain use cases - the fixes there also better
align tipc with the rest of the networking code.
The rest largely falls into routine cleanup category, by getting
rid of some unused routines, some Kconfig clutter, etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mac80211 checks the DS params IE if present and
uses it for the (primary) BSS channel, instead of the one
that the frame was received on. This is particularly useful
in the 2.4 GHz band since a frame is often received on one
of the adjacent channels due to overlap.
Move this code to cfg80211 so other drivers also do this.
Additionally, on 5 GHz, in particular with some (possibly)
upcoming changes in 802.11ai and duplicate transmissions
when wider channels are used, something similar happens.
So if present, also use the (primary) channel information
contained in the HT operation IE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP doesn't support HT, or more importantly if
it does but we have to disable it because its IEs are
broken, don't advertise HT support in our association
request. Otherwise, we configure our channel to be a
20 MHz non-HT channel but the AP might still think we
support HT, or even 40 MHz.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since the 11n spec amendment was rolled into the
2012 version, "11n" no longer makes sense. Use
"HT" instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver doesn't support 40 MHz channels, then
mac80211 erroneously sets number of RX chains to one
although the number of chains is independent of the
support for 40 MHz channels.
Fix this by checking the 40 MHz support only for the
code that sets the 40 MHz channel not the complete
HT code block.
This also means the HT20 channel type will always be
set in the changed code block so there's no need to
set it in case we override the AP due to invalid IEs
in the probe response/beacon.
The indentation is a bit quirky, but I'm rewriting
this code for VHT support so this will change again
very soon.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The radiotap vendor area in the skb head must be skipped
and accounted for in a few functions until it is removed.
I missed this in my patch, so a few places use this data
as though it was the 802.11 header, fix these places.
Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Starting from 3.6 we cache output routes for
multicasts only when using route to 224/4. For local receivers
we can set RTCF_LOCAL flag depending on the membership but
in such case we use maddr and saddr which are not caching
keys as before. Additionally, we can not use same place to
cache routes that differ in RTCF_LOCAL flag value.
Fix it by caching only RTCF_MULTICAST entries
without RTCF_LOCAL (send-only, no loopback). As a side effect,
we avoid unneeded lookup for fnhe when not caching because
multicasts are not redirected and they do not learn PMTU.
Thanks to Maxime Bizon for showing the caching
problems in __mkroute_output for 3.6 kernels: different
RTCF_LOCAL flag in cache can lead to wrong ip_mc_output or
ip_output call and the visible problem is that traffic can
not reach local receivers via loopback.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is work the same as for ipv4.
All other hacks about tcp repair are in common code for ipv4 and ipv6,
so this patch is enough for repairing ipv6 connections.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains two Netfilter fixes:
* Fix buffer overflow in the name of the timeout policy object
in the cttimeout infrastructure, from Florian Westphal.
* Fix a bug in the hash set in case that IP ranges are
specified, from Jozsef Kadlecsik.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
This pull request is intended for net-next and contains the following changes:
1) Remove a redundant check when initializing the xfrm replay functions,
from Ulrich Weber.
2) Use a faster per-cpu helper when allocating ipcomt transforms,
from Shan Wei.
3) Use a static gc threshold value for ipv6, simmilar to what we do
for ipv4 now.
4) Remove a commented out function call.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
This pull request is intended for 3.7 and contains a single patch to
fix the IPsec gc threshold value for ipv4.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There used to be a time when TIPC had lots of Kconfig knobs the
end user could alter, but they have all been made automatic or
obsolete, with the exception of CONFIG_TIPC_PORTS. This
previously existing set of options was all hidden under the
TIPC_ADVANCED setting, which does not exist in any code, but
only in Kconfig scope.
Having this now, just to hide the one remaining "advanced"
option no longer makes sense. Remove it. Also get rid of the
ifdeffery in the TIPC code that allowed for TIPC_PORTS to be
possibly undefined.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
As the variable:node is currently defined to u32 type, it is
unnecessary to cast its type to u32 again when using it.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Upon establishing a first link between two nodes, there is
currently a risk that the two endpoints will disagree on exactly
which sequence number reception and acknowleding of broadcast
packets should start.
The following scenarios may happen:
1: Node A sends an ACTIVATE message to B, telling it to start acking
packets from sequence number N.
2: Node A sends out broadcast N, but does not expect an acknowledge
from B, since B is not yet in its broadcast receiver's list.
3: Node A receives ACK for N from all nodes except B, and releases
packet N.
4: Node B receives the ACTIVATE, activates its link endpoint, and
stores the value N as sequence number of first expected packet.
5: Node B sends a NAME_DISTR message to A.
6: Node A receives the NAME_DISTR message, and activates its endpoint.
At this moment B is added to A's broadcast receiver's set.
Node A also sets sequence number 0 as the first broadcast packet
to be received from B.
7: Node A sends broadcast N+1.
8: B receives N+1, determines there is a gap in the sequence, since
it is expecting N, and sends a NACK for N back to A.
9: Node A has already released N, so no retransmission is possible.
The broadcast link in direction A->B is stale.
In addition to, or instead of, 7-9 above, the following may happen:
10: Node B sends broadcast M > 0 to A.
11: Node A receives M, falsely decides there must be a gap, since
it is expecting packet 0, and asks for retransmission of packets
[0,M-1].
12: Node B has already released these packets, so the broadcast
link is stale in direction B->A.
We solve this problem by introducing a new unicast message type,
BCAST_PROTOCOL/STATE, to convey the sequence number of the next
sent broadcast packet to the other endpoint, at exactly the moment
that endpoint is added to the own node's broadcast receivers list,
and before any other unicast messages are permitted to be sent.
Furthermore, we don't allow any node to start receiving and
processing broadcast packets until this new synchronization
message has been received.
To maintain backwards compatibility, we still open up for
broadcast reception if we receive a NAME_DISTR message without
any preceding broadcast sync message. In this case, we must
assume that the other end has an older code version, and will
never send out the new synchronization message. Hence, for mixed
old and new nodes, the issue arising in 7-12 of the above may
happen with the same probability as before.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Inherit netprio configuration from ->css_online(), allow nesting and
remove .broken_hierarchy marking. This makes netprio_cgroup's
behavior match netcls_cgroup's.
Note that this patch changes userland-visible behavior. Nesting is
allowed and the first level cgroups below the root cgroup behave
differently - they inherit priorities from the root cgroup on creation
instead of starting with 0. This is unfortunate but not doing so is
much crazier.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-and-Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: David S. Miller <davem@davemloft.net>
Introduce two helpers - netprio_prio() and netprio_set_prio() - which
hide the details of priomap access and expansion. This will help
implementing hierarchy support.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-and-Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: David S. Miller <davem@davemloft.net>
With priomap expansion no longer depending on knowing max id
allocated, netprio_cgroup can use cgroup->id insted of cs->prioidx.
Drop prioidx alloc/free logic and convert all uses to cgroup->id.
* In cgrp_css_alloc(), parent->id test is moved above @cs allocation
to simplify error path.
* In cgrp_css_free(), @cs assignment is made initialization.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-and-Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: David S. Miller <davem@davemloft.net>
netprio kept track of the highest prioidx allocated and resized
priomaps accordingly when necessary. This makes it necessary to keep
track of prioidx allocation and may end up resizing on every new
prioidx.
Update extend_netdev_table() such that it takes @target_idx which the
priomap should be able to accomodate. If the priomap is large enough,
nothing happens; otherwise, the size is doubled until @target_idx can
be accomodated.
This makes max_prioidx and write_update_netdev_table() unnecessary.
write_priomap() now calls extend_netdev_table() directly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-and-Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: David S. Miller <davem@davemloft.net>
The function is about to go through a rewrite. In preparation,
shorten the variable names so that we don't repeat "priomap" so often.
This patch is cosmetic.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-and-Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: David S. Miller <davem@davemloft.net>
sscanf() doesn't bite.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-and-Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: David S. Miller <davem@davemloft.net>
It turns out that we'll have to live with attributes which are
inherited at cgroup creation time but not affected by further updates
to the parent afterwards - such attributes are already in wide use
e.g. for cpuset.
So, there's nothing to do for netcls_cgroup for hierarchy support.
Its current behavior - inherit only during creation - is good enough.
Move config inheriting from ->css_alloc() to ->css_online() for
consistency, which doesn't change behavior at all, and remove
.broken_hierarchy marking.
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-and-Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: David S. Miller <davem@davemloft.net>
Rename the "supported" flag in bclink structure to "recv_permitted"
to better reflect what it is used for. When this flag is set for a
given node, we are permitted to receive and acknowledge broadcast
messages from that node. Convert it to a bool at the same time,
since it is not used to store any numerical values.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The "supportable" flag in bclink structure is a compatibility flag
indicating whether a peer node is capable of receiving TIPC broadcast
messages. However, all TIPC versions since tipc-1.5, and after the
inclusion in the upstream Linux kernel in 2006, support this capability.
It is highly unlikely that anybody is still using such an old
version of TIPC, let alone that they want to mix it with TIPC-2.0
nodes. Therefore, we now remove the "supportable" flag.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Currently at the TIPC bearer layer there is the following congestion
mechanism:
Once sending packets has failed via that bearer, the bearer will be
flagged as being in congested state at once. During bearer congestion,
all packets arriving at link will be queued on the link's outgoing
buffer. When we detect that the state of bearer congestion has
relaxed (e.g. some packets are received from the bearer) we will try
our best to push all packets in the link's outgoing buffer until the
buffer is empty, or until the bearer is congested again.
However, in fact the TIPC bearer never receives any feedback from the
device layer whether a send was successful or not, so it must always
assume it was successful. Therefore, the bearer congestion mechanism
as it exists currently is of no value.
But the bearer blocking state is still useful for us. For example,
when the physical media goes down/up, we need to change the state of
the links bound to the bearer. So the code maintaing the state
information is not removed.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
When a socket is shut down, we should wake up all thread sleeping on
it, instead of just one of them. Otherwise, when several threads are
polling the same socket, and one of them does shutdown(), the
remaining threads may end up sleeping forever.
Also, to align socket usage with common practice in other stacks, we
use one of the common socket callback handlers, sk_state_change(),
to wake up pending users. This is similar to the usage in e.g.
inet_shutdown(). [net/ipv4/af_inet.c].
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Chen Gang reports:
the length of nla_data(cda[CTA_TIMEOUT_NAME]) is not limited in server side.
And indeed, its used to strcpy to a fixed-sized buffer.
Fortunately, nfnetlink users need CAP_NET_ADMIN.
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
