Four patches from Or that add Hairpin support to mlx5:
===========================================================
From: Or Gerlitz <ogerlitz@mellanox.com>
We refer the ability of NIC HW to fwd packet received on one port to
the other port (also from a port to itself) as hairpin. The application API
is based
on ingress tc/flower rules set on the NIC with the mirred redirect
action. Other actions can apply to packets during the redirect.
Hairpin allows to offload the data-path of various SW DDoS gateways,
load-balancers, etc to HW. Packets go through all the required
processing in HW (header re-write, encap/decap, push/pop vlan) and
then forwarded, CPU stays at practically zero usage. HW Flow counters
are used by the control plane for monitoring and accounting.
Hairpin is implemented by pairing a receive queue (RQ) to send queue (SQ).
All the flows that share <recv NIC, mirred NIC> are redirected through
the same hairpin pair. Currently, only header-rewrite is supported as a
packet modification action.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing this
functionality
on HW simulator, before it was avail in the FW so the driver code could be
tested early.
===========================================================
From Feras three patches that provide very small changes that allow IPoIB
to support RX timestamping for child interfaces, simply by hooking the mlx5e
timestamping PTP ioctl to IPoIB child interface netdev profile.
One patch from Gal to fix a spilling mistake.
Two patches from Eugenia adds drop counters to VF statistics
to be reported as part of VF statistics in netlink (iproute2) and
implemented them in mlx5 eswitch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaVF5WAAoJEEg/ir3gV/o+fRkH/0PxjwJRA3REqhi/H8HOdH9f
cBLrOzFdqTCYQWQFCLFbMQ/Zgoel3KglpJ0iQMjuVFfjMbybVXOe8FAEVdbWHnfL
C+2HRMe8dplKrsq5UkxJhbyKhFKhl2XeMFYWonw9dSM7Nz5DyowQ1y1r5SgMlMAv
t3mYAIa4kZHK18BjDoIsCoAXXwsHiztR2irMp5+DwataTGP7vC7AsrucDxLA/qFf
I3E15DZk9s1f53PUuY7CYnUnJfMMP3VJdxpyx4k6xt9J2IMuilF4YyD6wpAKsVQU
/LzRkWI9x/6QindffqlrACeeidimOeY4pC4txIhS5uXgFXulugDHq1/Ih1sgZS8=
=g5vr
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-01-08' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
mlx5-updates-2018-01-08
Four patches from Or that add Hairpin support to mlx5:
===========================================================
From: Or Gerlitz <ogerlitz@mellanox.com>
We refer the ability of NIC HW to fwd packet received on one port to
the other port (also from a port to itself) as hairpin. The application API
is based
on ingress tc/flower rules set on the NIC with the mirred redirect
action. Other actions can apply to packets during the redirect.
Hairpin allows to offload the data-path of various SW DDoS gateways,
load-balancers, etc to HW. Packets go through all the required
processing in HW (header re-write, encap/decap, push/pop vlan) and
then forwarded, CPU stays at practically zero usage. HW Flow counters
are used by the control plane for monitoring and accounting.
Hairpin is implemented by pairing a receive queue (RQ) to send queue (SQ).
All the flows that share <recv NIC, mirred NIC> are redirected through
the same hairpin pair. Currently, only header-rewrite is supported as a
packet modification action.
I'd like to thanks Elijah Shakkour <elijahs@mellanox.com> for implementing this
functionality
on HW simulator, before it was avail in the FW so the driver code could be
tested early.
===========================================================
From Feras three patches that provide very small changes that allow IPoIB
to support RX timestamping for child interfaces, simply by hooking the mlx5e
timestamping PTP ioctl to IPoIB child interface netdev profile.
One patch from Gal to fix a spilling mistake.
Two patches from Eugenia adds drop counters to VF statistics
to be reported as part of VF statistics in netlink (iproute2) and
implemented them in mlx5 eswitch.
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-01-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Prevent out-of-bounds speculation in BPF maps by masking the
index after bounds checks in order to fix spectre v1, and
add an option BPF_JIT_ALWAYS_ON into Kconfig that allows for
removing the BPF interpreter from the kernel in favor of
JIT-only mode to make spectre v2 harder, from Alexei.
2) Remove false sharing of map refcount with max_entries which
was used in spectre v1, from Daniel.
3) Add a missing NULL psock check in sockmap in order to fix
a race, from John.
4) Fix test_align BPF selftest case since a recent change in
verifier rejects the bit-wise arithmetic on pointers
earlier but test_align update was missing, from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like commit e817f85652 ("xdp: generic XDP handling of
xdp_rxq_info") replaced kvfree(dev->_rx) in free_netdev() with
a call to netif_free_rx_queues() which doesn't actually free
the rings?
While at it remove the unnecessary temporary variable.
Fixes: e817f85652 ("xdp: generic XDP handling of xdp_rxq_info")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
kvzalloc'ed memory should be kvfree'd.
Fixes: e817f85652 ("xdp: generic XDP handling of xdp_rxq_info")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The BPF interpreter has been used as part of the spectre 2 attack CVE-2017-5715.
A quote from goolge project zero blog:
"At this point, it would normally be necessary to locate gadgets in
the host kernel code that can be used to actually leak data by reading
from an attacker-controlled location, shifting and masking the result
appropriately and then using the result of that as offset to an
attacker-controlled address for a load. But piecing gadgets together
and figuring out which ones work in a speculation context seems annoying.
So instead, we decided to use the eBPF interpreter, which is built into
the host kernel - while there is no legitimate way to invoke it from inside
a VM, the presence of the code in the host kernel's text section is sufficient
to make it usable for the attack, just like with ordinary ROP gadgets."
To make attacker job harder introduce BPF_JIT_ALWAYS_ON config
option that removes interpreter from the kernel in favor of JIT-only mode.
So far eBPF JIT is supported by:
x64, arm64, arm32, sparc64, s390, powerpc64, mips64
The start of JITed program is randomized and code page is marked as read-only.
In addition "constant blinding" can be turned on with net.core.bpf_jit_harden
v2->v3:
- move __bpf_prog_ret0 under ifdef (Daniel)
v1->v2:
- fix init order, test_bpf and cBPF (Daniel's feedback)
- fix offloaded bpf (Jakub's feedback)
- add 'return 0' dummy in case something can invoke prog->bpf_func
- retarget bpf tree. For bpf-next the patch would need one extra hunk.
It will be sent when the trees are merged back to net-next
Considered doing:
int bpf_jit_enable __read_mostly = BPF_EBPF_JIT_DEFAULT;
but it seems better to land the patch as-is and in bpf-next remove
bpf_jit_enable global variable from all JITs, consolidate in one place
and remove this jit_init() function.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add a sanity check to ensure that all requested ring parameters
are within bounds, which should reduce errors in driver implementation.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use AF_INET6 instead of AF_INET in IPv6-related code path
Signed-off-by: Andrii Vladyka <tulup@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern hardware can decide to drop packets going to/from a VF.
Add receive and transmit drop counters to be displayed at hypervisor
layer in iproute2 per VF statistics.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Now all XDP driver have been updated to setup xdp_rxq_info and assign
this to xdp_buff->rxq. Thus, it is now safe to enable access to some
of the xdp_rxq_info struct members.
This patch extend xdp_md and expose UAPI to userspace for
ingress_ifindex and rx_queue_index. Access happens via bpf
instruction rewrite, that load data directly from struct xdp_rxq_info.
* ingress_ifindex map to xdp_rxq_info->dev->ifindex
* rx_queue_index map to xdp_rxq_info->queue_index
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Hook points for xdp_rxq_info:
* reg : netif_alloc_rx_queues
* unreg: netif_free_rx_queues
The net_device have some members (num_rx_queues + real_num_rx_queues)
and data-area (dev->_rx with struct netdev_rx_queue's) that were
primarily used for exporting information about RPS (CONFIG_RPS) queues
to sysfs (CONFIG_SYSFS).
For generic XDP extend struct netdev_rx_queue with the xdp_rxq_info,
and remove some of the CONFIG_SYSFS ifdefs.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The driver code qede_free_fp_array() depend on kfree() can be called
with a NULL pointer. This stems from the qede_alloc_fp_array()
function which either (kz)alloc memory for fp->txq or fp->rxq.
This also simplifies error handling code in case of memory allocation
failures, but xdp_rxq_info_unreg need to know the difference.
Introduce xdp_rxq_info_is_reg() to handle if a memory allocation fails
and detect this is the failure path by seeing that xdp_rxq_info was
not registred yet, which first happens after successful alloaction in
qede_init_fp().
Driver hook points for xdp_rxq_info:
* reg : qede_init_fp
* unreg: qede_free_fp_array
Tested on actual hardware with samples/bpf program.
V2: Driver have no proper error path for failed XDP RX-queue info reg, as
qede_init_fp() is a void function.
Cc: everest-linux-l2@cavium.com
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch only introduce the core data structures and API functions.
All XDP enabled drivers must use the API before this info can used.
There is a need for XDP to know more about the RX-queue a given XDP
frames have arrived on. For both the XDP bpf-prog and kernel side.
Instead of extending xdp_buff each time new info is needed, the patch
creates a separate read-mostly struct xdp_rxq_info, that contains this
info. We stress this data/cache-line is for read-only info. This is
NOT for dynamic per packet info, use the data_meta for such use-cases.
The performance advantage is this info can be setup at RX-ring init
time, instead of updating N-members in xdp_buff. A possible (driver
level) micro optimization is that xdp_buff->rxq assignment could be
done once per XDP/NAPI loop. The extra pointer deref only happens for
program needing access to this info (thus, no slowdown to existing
use-cases).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This function is used from two places: rtnl_dump_ifinfo and
rtnl_getlink. In rtnl_getlink(), we give a request skb into
get_target_net(), but in rtnl_dump_ifinfo, we give a response skb
into get_target_net().
The problem here is that NETLINK_CB() isn't initialized for the response
skb. In both cases we can get a user socket and give it instead of skb
into get_target_net().
This bug was found by syzkaller with this call-trace:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 3149 Comm: syzkaller140561 Not tainted 4.15.0-rc4-mm1+ #47
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:__netlink_ns_capable+0x8b/0x120 net/netlink/af_netlink.c:868
RSP: 0018:ffff8801c880f348 EFLAGS: 00010206
RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff8443f900
RDX: 000000000000007b RSI: ffffffff86510f40 RDI: 00000000000003d8
RBP: ffff8801c880f360 R08: 0000000000000000 R09: 1ffff10039101e4f
R10: 0000000000000000 R11: 0000000000000001 R12: ffffffff86510f40
R13: 000000000000000c R14: 0000000000000004 R15: 0000000000000011
FS: 0000000001a1a880(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020151000 CR3: 00000001c9511005 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
netlink_ns_capable+0x26/0x30 net/netlink/af_netlink.c:886
get_target_net+0x9d/0x120 net/core/rtnetlink.c:1765
rtnl_dump_ifinfo+0x2e5/0xee0 net/core/rtnetlink.c:1806
netlink_dump+0x48c/0xce0 net/netlink/af_netlink.c:2222
__netlink_dump_start+0x4f0/0x6d0 net/netlink/af_netlink.c:2319
netlink_dump_start include/linux/netlink.h:214 [inline]
rtnetlink_rcv_msg+0x7f0/0xb10 net/core/rtnetlink.c:4485
netlink_rcv_skb+0x21e/0x460 net/netlink/af_netlink.c:2441
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4540
netlink_unicast_kernel net/netlink/af_netlink.c:1308 [inline]
netlink_unicast+0x4be/0x6a0 net/netlink/af_netlink.c:1334
netlink_sendmsg+0xa4a/0xe60 net/netlink/af_netlink.c:1897
Cc: Jiri Benc <jbenc@redhat.com>
Fixes: 79e1ad148c ("rtnetlink: use netnsid to query interface")
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kernel log ths message appears on every boot:
"warning: `NetworkChangeNo' uses legacy ethtool link settings API,
link modes are only partially reported"
When ethtool link settings API changed, it started complaining about
usages of old API. Ironically, the original patch was from google but
the application using the legacy API is chrome.
Linux ABI is fixed as much as possible. The kernel must not break it
and should not complain about applications using legacy API's.
This patch just removes the warning since using legacy API's
in Linux is perfectly acceptable.
Fixes: 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 87c320e515.
Changing the error return code in some situations turns out to
be harmful in practice. In particular Michael Ellerman reports
that DHCP fails on his powerpc machines, and this revert gets
things working again.
Johannes Berg agrees that this revert is the best course of
action for now.
Fixes: 029b6d1405 ("Revert "net: core: maybe return -EEXIST in __dev_alloc_name"")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv6/ip6_gre.c is a case of parallel adds.
include/trace/events/tcp.h is a little bit more tricky. The removal
of in-trace-macro ifdefs in 'net' paralleled with moving
show_tcp_state_name and friends over to include/trace/events/sock.h
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_ubufs must unclone before it is safe to modify its
skb_shared_info with skb_zcopy_clear.
Commit b90ddd5687 ("skbuff: skb_copy_ubufs must release uarg even
without user frags") ensures that all skbs release their zerocopy
state, even those without frags.
But I forgot an edge case where such an skb arrives that is cloned.
The stack does not build such packets. Vhost/tun skbs have their
frags orphaned before cloning. TCP skbs only attach zerocopy state
when a frag is added.
But if TCP packets can be trimmed or linearized, this might occur.
Tracing the code I found no instance so far (e.g., skb_linearize
ends up calling skb_zcopy_clear if !skb->data_len).
Still, it is non-obvious that no path exists. And it is fragile to
rely on this.
Fixes: b90ddd5687 ("skbuff: skb_copy_ubufs must release uarg even without user frags")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2017-12-28
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Fix incorrect state pruning related to recognition of zero initialized
stack slots, where stacksafe exploration would mistakenly return a
positive pruning verdict too early ignoring other slots, from Gianluca.
2) Various BPF to BPF calls related follow-up fixes. Fix an off-by-one
in maximum call depth check, and rework maximum stack depth tracking
logic to fix a bypass of the total stack size check reported by Jann.
Also fix a bug in arm64 JIT where prog->jited_len was uninitialized.
Addition of various test cases to BPF selftests, from Alexei.
3) Addition of a BPF selftest to test_verifier that is related to BPF to
BPF calls which demonstrates a late caller stack size increase and
thus out of bounds access. Fixed above in 2). Test case from Jann.
4) Addition of correlating BPF helper calls, BPF to BPF calls as well
as BPF maps to bpftool xlated dump in order to allow for better
BPF program introspection and debugging, from Daniel.
5) Fixing several bugs in BPF to BPF calls kallsyms handling in order
to get it actually to work for subprogs, from Daniel.
6) Extending sparc64 JIT support for BPF to BPF calls and fix a couple
of build errors for libbpf on sparc64, from David.
7) Allow narrower context access for BPF dev cgroup typed programs in
order to adapt to LLVM code generation. Also adjust memlock rlimit
in the test_dev_cgroup BPF selftest, from Yonghong.
8) Add netdevsim Kconfig entry to BPF selftests since test_offload.py
relies on netdevsim device being available, from Jakub.
9) Reduce scope of xdp_do_generic_redirect_map() to being static,
from Xiongwei.
10) Minor cleanups and spelling fixes in BPF verifier, from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a net-next follow-up to commit 268b790679 ("skbuff: orphan
frags before zerocopy clone"), which fixed a bug in net, but added a
call to skb_zerocopy_clone at each frag to do so.
When segmenting skbs with user frags, either the user frags must be
replaced with private copies and uarg released, or the uarg must have
its refcount increased for each new skb.
skb_orphan_frags does the first, except for cases that can handle
reference counting. skb_zerocopy_clone then does the second.
Call these once per nskb, instead of once per frag.
That is, in the common case. With a frag list, also refresh when the
origin skb (frag_skb) changes.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-12-22
1) Separate ESP handling from segmentation for GRO packets.
This unifies the IPsec GSO and non GSO codepath.
2) Add asynchronous callbacks for xfrm on layer 2. This
adds the necessary infrastructure to core networking.
3) Allow to use the layer2 IPsec GSO codepath for software
crypto, all infrastructure is there now.
4) Also allow IPsec GSO with software crypto for local sockets.
5) Don't require synchronous crypto fallback on IPsec offloading,
it is not needed anymore.
6) Check for xdo_dev_state_free and only call it if implemented.
From Shannon Nelson.
7) Check for the required add and delete functions when a driver
registers xdo_dev_ops. From Shannon Nelson.
8) Define xfrmdev_ops only with offload config.
From Shannon Nelson.
9) Update the xfrm stats documentation.
From Shannon Nelson.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The batman-adv unicast packets contain a full layer 2 frame in encapsulated
form. The flow dissector must therefore be able to parse the batman-adv
unicast header to reach the layer 2+3 information.
+--------------------+
| ip(v6)hdr |
+--------------------+
| inner ethhdr |
+--------------------+
| batadv unicast hdr |
+--------------------+
| outer ethhdr |
+--------------------+
The obtained information from the upper layer can then be used by RPS to
schedule the processing on separate cores. This allows better distribution
of multiple flows from the same neighbor to different cores.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_copy_ubufs creates a private copy of frags[] to release its hold
on user frags, then calls uarg->callback to notify the owner.
Call uarg->callback even when no frags exist. This edge case can
happen when zerocopy_sg_from_iter finds enough room in skb_headlen
to copy all the data.
Fixes: 3ece782693 ("sock: skb_copy_ubufs support for compound pages")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_zerocopy_clone after skb_orphan_frags, to avoid duplicate
calls to skb_uarg(skb)->callback for the same data.
skb_zerocopy_clone associates skb_shinfo(skb)->uarg from frag_skb
with each segment. This is only safe for uargs that do refcounting,
which is those that pass skb_orphan_frags without dropping their
shared frags. For others, skb_orphan_frags drops the user frags and
sets the uarg to NULL, after which sock_zerocopy_clone has no effect.
Qemu hangs were reported due to duplicate vhost_net_zerocopy_callback
calls for the same data causing the vhost_net_ubuf_ref_>refcount to
drop below zero.
Link: http://lkml.kernel.org/r/<CAF=yD-LWyCD4Y0aJ9O0e_CHLR+3JOeKicRRTEVCPxgw4XOcqGQ@mail.gmail.com>
Fixes: 1f8b977ab3 ("sock: enable MSG_ZEROCOPY")
Reported-by: Andreas Hartmann <andihartmann@01019freenet.de>
Reported-by: David Hill <dhill@redhat.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(I can trivially verify that that idr_remove in cleanup_net happens
after the network namespace count has dropped to zero --EWB)
Function get_net_ns_by_id() does not check for net::count
after it has found a peer in netns_ids idr.
It may dereference a peer, after its count has already been
finaly decremented. This leads to double free and memory
corruption:
put_net(peer) rtnl_lock()
atomic_dec_and_test(&peer->count) [count=0] ...
__put_net(peer) get_net_ns_by_id(net, id)
spin_lock(&cleanup_list_lock)
list_add(&net->cleanup_list, &cleanup_list)
spin_unlock(&cleanup_list_lock)
queue_work() peer = idr_find(&net->netns_ids, id)
| get_net(peer) [count=1]
| ...
| (use after final put)
v ...
cleanup_net() ...
spin_lock(&cleanup_list_lock) ...
list_replace_init(&cleanup_list, ..) ...
spin_unlock(&cleanup_list_lock) ...
... ...
... put_net(peer)
... atomic_dec_and_test(&peer->count) [count=0]
... spin_lock(&cleanup_list_lock)
... list_add(&net->cleanup_list, &cleanup_list)
... spin_unlock(&cleanup_list_lock)
... queue_work()
... rtnl_unlock()
rtnl_lock() ...
for_each_net(tmp) { ...
id = __peernet2id(tmp, peer) ...
spin_lock_irq(&tmp->nsid_lock) ...
idr_remove(&tmp->netns_ids, id) ...
... ...
net_drop_ns() ...
net_free(peer) ...
} ...
|
v
cleanup_net()
...
(Second free of peer)
Also, put_net() on the right cpu may reorder with left's cpu
list_replace_init(&cleanup_list, ..), and then cleanup_list
will be corrupted.
Since cleanup_net() is executed in worker thread, while
put_net(peer) can happen everywhere, there should be
enough time for concurrent get_net_ns_by_id() to pick
the peer up, and the race does not seem to be unlikely.
The patch fixes the problem in standard way.
(Also, there is possible problem in peernet2id_alloc(), which requires
check for net::count under nsid_lock and maybe_get_net(peer), but
in current stable kernel it's used under rtnl_lock() and it has to be
safe. Openswitch begun to use peernet2id_alloc(), and possibly it should
be fixed too. While this is not in stable kernel yet, so I'll send
a separate message to netdev@ later).
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Fixes: 0c7aecd4bd "netns: add rtnl cmd to add and get peer netns ids"
Reviewed-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements asynchronous crypto callbacks
and a backlog handler that can be used when IPsec
is done at layer 2 in the TX path. It also extends
the skb validate functions so that we can update
the driver transmit return codes based on async
crypto operation or to indicate that we queued the
packet in a backlog queue.
Joint work with: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We change the ESP GSO handlers to only segment the packets.
The ESP handling and encryption is defered to validate_xmit_xfrm()
where this is done for non GRO packets too. This makes the code
more robust and prepares for asynchronous crypto handling.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Hardware should not aggregate any packets when generic XDP is installed.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce NETIF_F_GRO_HW feature flag for NICs that support hardware
GRO. With this flag, we can now independently turn on or off hardware
GRO when GRO is on. Previously, drivers were using NETIF_F_GRO to
control hardware GRO and so it cannot be independently turned on or
off without affecting GRO.
Hardware GRO (just like GRO) guarantees that packets can be re-segmented
by TSO/GSO to reconstruct the original packet stream. Logically,
GRO_HW should depend on GRO since it a subset, but we will let
individual drivers enforce this dependency as they see fit.
Since NETIF_F_GRO is not propagated between upper and lower devices,
NETIF_F_GRO_HW should follow suit since it is a subset of GRO. In other
words, a lower device can independent have GRO/GRO_HW enabled or disabled
and no feature propagation is required. This will preserve the current
GRO behavior. This can be changed later if we decide to propagate GRO/
GRO_HW/RXCSUM from upper to lower devices.
Cc: Ariel Elior <Ariel.Elior@cavium.com>
Cc: everest-linux-l2@cavium.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some case, we want to know how many sockets are in use in
different _net_ namespaces. It's a key resource metric.
This patch add a member in struct netns_core. This is a counter
for socket-inuse in the _net_ namespace. The patch will add/sub
counter in the sk_alloc, sk_clone_lock and __sk_free.
This patch will not counter the socket created in kernel.
It's not very useful for userspace to know how many kernel
sockets we created.
The main reasons for doing this are that:
1. When linux calls the 'do_exit' for process to exit, the functions
'exit_task_namespaces' and 'exit_task_work' will be called sequentially.
'exit_task_namespaces' may have destroyed the _net_ namespace, but
'sock_release' called in 'exit_task_work' may use the _net_ namespace
if we counter the socket-inuse in sock_release.
2. socket and sock are in pair. More important, sock holds the _net_
namespace. We counter the socket-inuse in sock, for avoiding holding
_net_ namespace again in socket. It's a easy way to maintain the code.
Signed-off-by: Martin Zhang <zhangjunweimartin@didichuxing.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the member name will make the code more readable.
This patch will be used in next patch.
Signed-off-by: Martin Zhang <zhangjunweimartin@didichuxing.com>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function xdp_do_generic_redirect_map() is only used in this file, so
make it static.
Clean up sparse warning:
net/core/filter.c:2687:5: warning: no previous prototype
for 'xdp_do_generic_redirect_map' [-Wmissing-prototypes]
Signed-off-by: Xiongwei Song <sxwjean@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Daniel Borkmann says:
====================
pull-request: bpf 2017-12-17
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix a corner case in generic XDP where we have non-linear skbs
but enough tailroom in the skb to not miss to linearizing there,
from Song.
2) Fix BPF JIT bugs in s390x and ppc64 to not recache skb data when
BPF context is not skb, from Daniel.
3) Fix a BPF JIT bug in sparc64 where recaching skb data after helper
call would use the wrong register for the skb, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_complete_tx_timestamp must ingest the skb it is passed. Call
kfree_skb if the skb cannot be enqueued.
Fixes: b245be1f4d ("net-timestamp: no-payload only sysctl")
Fixes: 9ac25fc063 ("net: fix socket refcounting in skb_complete_tx_timestamp()")
Reported-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netif_receive_generic_xdp(), it is necessary to linearize all
nonlinear skb. However, in current implementation, skb with
troom <= 0 are not linearized. This patch fixes this by calling
skb_linearize() for all nonlinear skb.
Fixes: de8f3a83b0 ("bpf: add meta pointer for direct access")
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
skb_warn_bad_offload warns when packets enter the GSO stack that
require skb_checksum_help or vice versa. Do not warn on arbitrary
bad packets. Packet sockets can craft many. Syzkaller was able to
demonstrate another one with eth_type games.
In particular, suppress the warning when segmentation returns an
error, which is for reasons other than checksum offload.
See also commit 36c9247449 ("net: WARN if skb_checksum_help() is
called on skb requiring segmentation") for context on this warning.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 46e6b992c2 ("rtnetlink: allow GSO maximums to be set on device creation")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink device already allows changing GSO sizes with
ip set command. The part that is missing is allowing overriding
GSO settings on device creation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sch_mq qdisc creates a sub-qdisc per tx queue which are then
called independently for enqueue and dequeue operations. However
statistics are aggregated and pushed up to the "master" qdisc.
This patch adds support for any of the sub-qdiscs to be per cpu
statistic qdiscs. To handle this case add a check when calculating
stats and aggregate the per cpu stats if needed.
Also exports __gnet_stats_copy_queue() to use as a helper function.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a flag for queueing disciplines to indicate the stack
does not need to use the qdisc lock to protect operations. This can
be used to build lockless scheduling algorithms and improving
performance.
The flag is checked in the tx path and the qdisc lock is only taken
if it is not set. For now use a conditional if statement. Later we
could be more aggressive if it proves worthwhile and use a static key
or wrap this in a likely().
Also the lockless case drops the TCQ_F_CAN_BYPASS logic. The reason
for this is synchronizing a qlen counter across threads proves to
cost more than doing the enqueue/dequeue operations when tested with
pktgen.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __qdisc_run calls qdisc_run_end() but does not call
qdisc_run_begin(). This makes it hard to track pairs of
qdisc_run_{begin,end} across function calls.
To simplify reading these code paths this patch moves begin/end calls
into qdisc_run().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2017-12-07
The following pull-request contains BPF updates for your net-next tree.
The main changes are:
1) Detailed documentation of BPF development process from Daniel.
2) Addition of is_fullsock, snd_cwnd and srtt_us fields to bpf_sock_ops
from Lawrence.
3) Minor follow up for bpf_skb_set_tunnel_key() from William.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move dissection of tunnel info to outside of the main flow dissection
function, __skb_flow_dissect(). The sole user of this feature, the flower
classifier, is updated to call tunnel info dissection directly, using
skb_flow_dissect_tunnel_info().
This results in a slightly less complex implementation of
__skb_flow_dissect(), in particular removing logic from that call path
which is not used by the majority of users. The expense of this is borne by
the flower classifier which now has to make an extra call for tunnel info
dissection.
This patch should not result in any behavioural change.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d6f295e9def0; some userspace (in the case
we noticed it's wpa_supplicant), is relying on the current
error code to determine that a fixed name interface already
exists.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds read access to snd_cwnd and srtt_us fields of tcp_sock. Since these
fields are only valid if the socket associated with the sock_ops program
call is a full socket, the field is_fullsock is also added to the
bpf_sock_ops struct. If the socket is not a full socket, reading these
fields returns 0.
Note that in most cases it will not be necessary to check is_fullsock to
know if there is a full socket. The context of the call, as specified by
the 'op' field, can sometimes determine whether there is a full socket.
The struct bpf_sock_ops has the following fields added:
__u32 is_fullsock; /* Some TCP fields are only valid if
* there is a full socket. If not, the
* fields read as zero.
*/
__u32 snd_cwnd;
__u32 srtt_us; /* Averaged RTT << 3 in usecs */
There is a new macro, SOCK_OPS_GET_TCP32(NAME), to make it easier to add
read access to more 32 bit tcp_sock fields.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
trivial move the BPF_F_ZERO_CSUM_TX check right below the
'flags & BPF_F_DONT_FRAGMENT', so common tun_flags handling
is logically together.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
convert remaining users of rtnl_register to rtnl_register_module
and un-export rtnl_register.
Requested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2017-12-03
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Addition of a software model for BPF offloads in order to ease
testing code changes in that area and make semantics more clear.
This is implemented in a new driver called netdevsim, which can
later also be extended for other offloads. SR-IOV support is added
as well to netdevsim. BPF kernel selftests for offloading are
added so we can track basic functionality as well as exercising
all corner cases around BPF offloading, from Jakub.
2) Today drivers have to drop the reference on BPF progs they hold
due to XDP on device teardown themselves. Change this in order
to make XDP handling inside the drivers less error prone, and
move disabling XDP to the core instead, also from Jakub.
3) Misc set of BPF verifier improvements and cleanups as preparatory
work for upcoming BPF-to-BPF calls. Among others, this set also
improves liveness marking such that pruning can be slightly more
effective. Register and stack liveness information is now included
in the verifier log as well, from Alexei.
4) nfp JIT improvements in order to identify load/store sequences in
the BPF prog e.g. coming from memcpy lowering and optimizing them
through the NPU's command push pull (CPP) instruction, from Jiong.
5) Cleanups to test_cgrp2_attach2.c BPF sample code in oder to remove
bpf_prog_attach() magic values and replacing them with actual proper
attach flag instead, from David.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes __rtnl_register and switches callers to either
rtnl_register or rtnl_register_module.
Also, rtnl_register() will now print an error if memory allocation
failed rather than panic the kernel.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add yet another rtnl_register function. It will be used by modules
that can be removed.
The passed module struct is used to prevent module unload while
a netlink dump is in progress or when a DOIT_UNLOCKED doit callback
is called.
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnetlink is littered with READ_ONCE() because we can have read accesses
while another cpu can write to the structure we're reading by
(un)registering doit or dumpit handlers.
This patch changes this so that (un)registering cpu allocates a new
structure and then publishes it via rcu_assign_pointer, i.e. once
another cpu can see such pointer no modifications will occur anymore.
based on initial patch from Peter Zijlstra.
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the patch, BPF_F_ZERO_CSUM_TX can be used only for ipv4 tunnel.
With introduction of ip6gretap collect_md mode, the flag should be also
supported for ipv6.
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since day one of XDP drivers had to remember to free the program
on the remove path. This leads to code duplication and is error
prone. Make the stack query the installed programs on unregister
and if something is installed, remove the program. Freeing of
program attached to XDP generic is moved from free_netdev() as well.
Because the remove will now be called before notifiers are
invoked, BPF offload state of the program will not get destroyed
before uninstall.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The output parameters will get unwieldy if we want to add more
information about the program. Simply pass the entire
struct netdev_bpf in.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Since commit e32ea7e747 ("soreuseport: fast reuseport UDP socket
selection") and commit c125e80b88 ("soreuseport: fast reuseport
TCP socket selection") the relevant reuseport socket matching the current
packet is selected by the reuseport_select_sock() call. The only
exceptions are invalid BPF filters/filters returning out-of-range
indices.
In the latter case the code implicitly falls back to using the hash
demultiplexing, but instead of selecting the socket inside the
reuseport_select_sock() function, it relies on the hash selection
logic introduced with the early soreuseport implementation.
With this patch, in case of a BPF filter returning a bad socket
index value, we fall back to hash-based selection inside the
reuseport_select_sock() body, so that we can drop some duplicate
code in the ipv4 and ipv6 stack.
This also allows faster lookup in the above scenario and will allow
us to avoid computing the hash value for successful, BPF based
demultiplexing - in a later patch.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first member of an IPSEC route bundle chain sets it's dst->path to
the underlying ipv4/ipv6 route that carries the bundle.
Stated another way, if one were to follow the xfrm_dst->child chain of
the bundle, the final non-NULL pointer would be the path and point to
either an ipv4 or an ipv6 route.
This is largely used to make sure that PMTU events propagate down to
the correct ipv4 or ipv6 route.
When we don't have the top of an IPSEC bundle 'dst->path == dst'.
Move it down into xfrm_dst and key off of dst->xfrm.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
The dst->from value is only used by ipv6 routes to track where
a route "came from".
Any time we clone or copy a core ipv6 route in the ipv6 routing
tables, we have the copy/clone's ->from point to the base route.
This is used to handle route expiration properly.
Only ipv6 uses this mechanism, and only ipv6 code references
it. So it is safe to move it into rt6_info.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
XFRM bundle child chains look like this:
xdst1 --> xdst2 --> xdst3 --> path_dst
All of xdstN are xfrm_dst objects and xdst->u.dst.xfrm is non-NULL.
The final child pointer in the chain, here called 'path_dst', is some
other kind of route such as an ipv4 or ipv6 one.
The xfrm output path pops routes, one at a time, via the child
pointer, until we hit one which has a dst->xfrm pointer which
is NULL.
We can easily preserve the above mechanisms with child sitting
only in the xfrm_dst structure. All children in the chain
before we break out of the xfrm_output() loop have dst->xfrm
non-NULL and are therefore xfrm_dst objects.
Since we break out of the loop when we find dst->xfrm NULL, we
will not try to dereference 'dst' as if it were an xfrm_dst.
Signed-off-by: David S. Miller <davem@davemloft.net>
Only IPSEC routes have a non-NULL dst->child pointer. And IPSEC
routes are identified by a non-NULL dst->xfrm pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
__poll_t is also used as wait key in some waitqueues.
Verify that wait_..._poll() gets __poll_t as key and
provide a helper for wakeup functions to get back to
that __poll_t value.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
Daniel Borkmann says:
====================
pull-request: bpf 2017-11-23
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Several BPF offloading fixes, from Jakub. Among others:
- Limit offload to cls_bpf and XDP program types only.
- Move device validation into the driver and don't make
any assumptions about the device in the classifier due
to shared blocks semantics.
- Don't pass offloaded XDP program into the driver when
it should be run in native XDP instead. Offloaded ones
are not JITed for the host in such cases.
- Don't destroy device offload state when moved to
another namespace.
- Revert dumping offload info into user space for now,
since ifindex alone is not sufficient. This will be
redone properly for bpf-next tree.
2) Fix test_verifier to avoid using bpf_probe_write_user()
helper in test cases, since it's dumping a warning into
kernel log which may confuse users when only running tests.
Switch to use bpf_trace_printk() instead, from Yonghong.
3) Several fixes for correcting ARG_CONST_SIZE_OR_ZERO semantics
before it becomes uabi, from Gianluca. More specifically:
- Add a type ARG_PTR_TO_MEM_OR_NULL that is used only
by bpf_csum_diff(), where the argument is either a
valid pointer or NULL. The subsequent ARG_CONST_SIZE_OR_ZERO
then enforces a valid pointer in case of non-0 size
or a valid pointer or NULL in case of size 0. Given
that, the semantics for ARG_PTR_TO_MEM in combination
with ARG_CONST_SIZE_OR_ZERO are now such that in case
of size 0, the pointer must always be valid and cannot
be NULL. This fix in semantics allows for bpf_probe_read()
to drop the recently added size == 0 check in the helper
that would become part of uabi otherwise once released.
At the same time we can then fix bpf_probe_read_str() and
bpf_perf_event_output() to use ARG_CONST_SIZE_OR_ZERO
instead of ARG_CONST_SIZE in order to fix recently
reported issues by Arnaldo et al, where LLVM optimizes
two boundary checks into a single one for unknown
variables where the verifier looses track of the variable
bounds and thus rejects valid programs otherwise.
4) A fix for the verifier for the case when it detects
comparison of two constants where the branch is guaranteed
to not be taken at runtime. Verifier will rightfully prune
the exploration of such paths, but we still pass the program
to JITs, where they would complain about using reserved
fields, etc. Track such dead instructions and sanitize
them with mov r0,r0. Rejection is not possible since LLVM
may generate them for valid C code and doesn't do as much
data flow analysis as verifier. For bpf-next we might
implement removal of such dead code and adjust branches
instead. Fix from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuntap and similar devices can inject GSO packets. Accept type
VIRTIO_NET_HDR_GSO_UDP, even though not generating UFO natively.
Processes are expected to use feature negotiation such as TUNSETOFFLOAD
to detect supported offload types and refrain from injecting other
packets. This process breaks down with live migration: guest kernels
do not renegotiate flags, so destination hosts need to expose all
features that the source host does.
Partially revert the UFO removal from 182e0b6b5846~1..d9d30adf5677.
This patch introduces nearly(*) no new code to simplify verification.
It brings back verbatim tuntap UFO negotiation, VIRTIO_NET_HDR_GSO_UDP
insertion and software UFO segmentation.
It does not reinstate protocol stack support, hardware offload
(NETIF_F_UFO), SKB_GSO_UDP tunneling in SKB_GSO_SOFTWARE or reception
of VIRTIO_NET_HDR_GSO_UDP packets in tuntap.
To support SKB_GSO_UDP reappearing in the stack, also reinstate
logic in act_csum and openvswitch. Achieve equivalence with v4.13 HEAD
by squashing in commit 939912216f ("net: skb_needs_check() removes
CHECKSUM_UNNECESSARY check for tx.") and reverting commit 8d63bee643
("net: avoid skb_warn_bad_offload false positives on UFO").
(*) To avoid having to bring back skb_shinfo(skb)->ip6_frag_id,
ipv6_proxy_select_ident is changed to return a __be32 and this is
assigned directly to the frag_hdr. Also, SKB_GSO_UDP is inserted
at the end of the enum to minimize code churn.
Tested
Booted a v4.13 guest kernel with QEMU. On a host kernel before this
patch `ethtool -k eth0` shows UFO disabled. After the patch, it is
enabled, same as on a v4.13 host kernel.
A UFO packet sent from the guest appears on the tap device:
host:
nc -l -p -u 8000 &
tcpdump -n -i tap0
guest:
dd if=/dev/zero of=payload.txt bs=1 count=2000
nc -u 192.16.1.1 8000 < payload.txt
Direct tap to tap transmission of VIRTIO_NET_HDR_GSO_UDP succeeds,
packets arriving fragmented:
./with_tap_pair.sh ./tap_send_ufo tap0 tap1
(from https://github.com/wdebruij/kerneltools/tree/master/tests)
Changes
v1 -> v2
- simplified set_offload change (review comment)
- documented test procedure
Link: http://lkml.kernel.org/r/<CAF=yD-LuUeDuL9YWPJD9ykOZ0QCjNeznPDr6whqZ9NGMNF12Mw@mail.gmail.com>
Fixes: fb652fdfe8 ("macvlan/macvtap: Remove NETIF_F_UFO advertisement.")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the current ARG_PTR_TO_MEM/ARG_PTR_TO_UNINIT_MEM semantics, an helper
argument can be NULL when the next argument type is ARG_CONST_SIZE_OR_ZERO
and the verifier can prove the value of this next argument is 0. However,
most helpers are just interested in handling <!NULL, 0>, so forcing them to
deal with <NULL, 0> makes the implementation of those helpers more
complicated for no apparent benefits, requiring them to explicitly handle
those corner cases with checks that bpf programs could start relying upon,
preventing the possibility of removing them later.
Solve this by making ARG_PTR_TO_MEM/ARG_PTR_TO_UNINIT_MEM never accept NULL
even when ARG_CONST_SIZE_OR_ZERO is set, and introduce a new argument type
ARG_PTR_TO_MEM_OR_NULL to explicitly deal with the NULL case.
Currently, the only helper that needs this is bpf_csum_diff_proto(), so
change arg1 and arg3 to this new type as well.
Also add a new battery of tests that explicitly test the
!ARG_PTR_TO_MEM_OR_NULL combination: all the current ones testing the
various <NULL, 0> variations are focused on bpf_csum_diff, so cover also
other helpers.
Signed-off-by: Gianluca Borello <g.borello@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently device-bound programs are not able to run on the host
to save resources (host JIT is not invoked). Don't allow XDP
programs to be attached without the HW_MODE flag. In theory
if program is already translated for device offload the driver
should choose to offload it instead of loading it in the driver.
However, offloading translated program may still fail resulting
in device-bound program being run on the host.
Prevent this by refusing to attach device bound programs if
XDP_FLAGS_HW_MODE is not set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
With TC shared block changes we can't depend on correct netdev
pointer being available in cls_bpf. Move the device validation
to the driver. Core will only make sure that offloaded programs
are always attached in the driver (or in HW by the driver). We
trust that drivers which implement offload callbacks will perform
necessary checks.
Moving the checks to the driver is generally a useful thing,
in practice the check should be against a switchdev instance,
not a netdev, given that most ASICs will probably allow using
the same program on many ports.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2 updates
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
memory hotplug: fix comments when adding section
mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
mm: simplify nodemask printing
mm,oom_reaper: remove pointless kthread_run() error check
mm/page_ext.c: check if page_ext is not prepared
writeback: remove unused function parameter
mm: do not rely on preempt_count in print_vma_addr
mm, sparse: do not swamp log with huge vmemmap allocation failures
mm/hmm: remove redundant variable align_end
mm/list_lru.c: mark expected switch fall-through
mm/shmem.c: mark expected switch fall-through
mm/page_alloc.c: broken deferred calculation
mm: don't warn about allocations which stall for too long
fs: fuse: account fuse_inode slab memory as reclaimable
mm, page_alloc: fix potential false positive in __zone_watermark_ok
mm: mlock: remove lru_add_drain_all()
mm, sysctl: make NUMA stats configurable
shmem: convert shmem_init_inodecache() to void
Unify migrate_pages and move_pages access checks
mm, pagevec: rename pagevec drained field
...
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of. Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact. Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.
This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache. Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop. It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.
The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path. A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.
Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "kmemcheck: kill kmemcheck", v2.
As discussed at LSF/MM, kill kmemcheck.
KASan is a replacement that is able to work without the limitation of
kmemcheck (single CPU, slow). KASan is already upstream.
We are also not aware of any users of kmemcheck (or users who don't
consider KASan as a suitable replacement).
The only objection was that since KASAN wasn't supported by all GCC
versions provided by distros at that time we should hold off for 2
years, and try again.
Now that 2 years have passed, and all distros provide gcc that supports
KASAN, kill kmemcheck again for the very same reasons.
This patch (of 4):
Remove kmemcheck annotations, and calls to kmemcheck from the kernel.
[alexander.levin@verizon.com: correctly remove kmemcheck call from dma_map_sg_attrs]
Link: http://lkml.kernel.org/r/20171012192151.26531-1-alexander.levin@verizon.com
Link: http://lkml.kernel.org/r/20171007030159.22241-2-alexander.levin@verizon.com
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tim Hansen <devtimhansen@gmail.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
There is at least unlocked deletion of net->ipv4.fib_notifier_ops
from net::fib_notifier_ops:
ip_fib_net_exit()
rtnl_unlock()
fib4_notifier_exit()
fib_notifier_ops_unregister(net->ipv4.notifier_ops)
list_del_rcu(&ops->list)
So fib_seq_sum() can't use rtnl_lock() only for protection.
The possible solution could be to use rtnl_lock()
in fib_notifier_ops_unregister(), but this adds
a possible delay during net namespace creation,
so we better use rcu_read_lock() till someone
really needs the mutex (if that happens).
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds netlink notifications on iflias changes via sysfs.
makes it consistent with the netlink path which also calls
netdev_state_change. Also makes it consistent with other sysfs
netdev_store operations.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If name contains a %, it's easy to see that this patch doesn't change
anything (other than eliminate the duplicate dev_valid_name
call). Otherwise, we'll now just spend a little time in snprintf()
copying name to the stack buffer allocated in dev_alloc_name_ns, and do
the __dev_get_by_name using that buffer rather than name.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we're given format string with no %d, -EEXIST is a saner error code.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently only exclude non-sysfs-friendly names via
dev_get_valid_name; there doesn't seem to be a reason to allow such
names when we're called via dev_alloc_name.
This does duplicate the dev_valid_name check in the dev_get_valid_name()
case; we'll fix that shortly.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only caller passes a stack buffer as buf, so it won't equal the
passed-in name. Moreover, we're already using buf as a scratch buffer
inside the if (p) {} block, so if buf and name were the same, that
snprintf() call would be overwriting its own format string.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_alloc_name contained a BUG_ON(), which I moved to dev_alloc_name_ns;
the only other caller of that already has the same BUG_ON.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_alloc_name is called from the public (and exported)
dev_alloc_name(), so we don't have a guarantee that strlen(name) is at
most IFNAMSIZ. If somebody manages to get __dev_alloc_name called with a
% char beyond the 31st character, we'd be making a snprintf() call that
will very easily crash the kernel (using an appropriate %p extension,
we'll likely dereference some completely bogus pointer).
In the normal case where strlen() is sane, we don't even save anything
by limiting to IFNAMSIZ, so just use strchr().
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
I had many reports that TSQ logic breaks wifi aggregation.
Current logic is to allow up to 1 ms of bytes to be queued into qdisc
and drivers queues.
But Wifi aggregation needs a bigger budget to allow bigger rates to
be discovered by various TCP Congestion Controls algorithms.
This patch adds an extra socket field, allowing wifi drivers to select
another log scale to derive TCP Small Queue credit from current pacing
rate.
Initial value is 10, meaning that this patch does not change current
behavior.
We expect wifi drivers to set this field to smaller values (tests have
been done with values from 6 to 9)
They would have to use following template :
if (skb->sk && skb->sk->sk_pacing_shift != MY_PACING_SHIFT)
skb->sk->sk_pacing_shift = MY_PACING_SHIFT;
Ref: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1670041
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Toke Høiland-Jørgensen <toke@toke.dk>
Cc: Kir Kolyshkin <kir@openvz.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be sure that rules_ops list initialized in net_init hook was return
to initial state.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be sure that fib_notifier_ops list initilized in net_init hook was return
to initial state.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be sure that dev_base_head list initialized in net_init hook was return
to initial state
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle are:
- Another attempt at enabling cross-release lockdep dependency
tracking (automatically part of CONFIG_PROVE_LOCKING=y), this time
with better performance and fewer false positives. (Byungchul Park)
- Introduce lockdep_assert_irqs_enabled()/disabled() and convert
open-coded equivalents to lockdep variants. (Frederic Weisbecker)
- Add down_read_killable() and use it in the VFS's iterate_dir()
method. (Kirill Tkhai)
- Convert remaining uses of ACCESS_ONCE() to
READ_ONCE()/WRITE_ONCE(). Most of the conversion was Coccinelle
driven. (Mark Rutland, Paul E. McKenney)
- Get rid of lockless_dereference(), by strengthening Alpha atomics,
strengthening READ_ONCE() with smp_read_barrier_depends() and thus
being able to convert users of lockless_dereference() to
READ_ONCE(). (Will Deacon)
- Various micro-optimizations:
- better PV qspinlocks (Waiman Long),
- better x86 barriers (Michael S. Tsirkin)
- better x86 refcounts (Kees Cook)
- ... plus other fixes and enhancements. (Borislav Petkov, Juergen
Gross, Miguel Bernal Marin)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
locking/x86: Use LOCK ADD for smp_mb() instead of MFENCE
rcu: Use lockdep to assert IRQs are disabled/enabled
netpoll: Use lockdep to assert IRQs are disabled/enabled
timers/posix-cpu-timers: Use lockdep to assert IRQs are disabled/enabled
sched/clock, sched/cputime: Use lockdep to assert IRQs are disabled/enabled
irq_work: Use lockdep to assert IRQs are disabled/enabled
irq/timings: Use lockdep to assert IRQs are disabled/enabled
perf/core: Use lockdep to assert IRQs are disabled/enabled
x86: Use lockdep to assert IRQs are disabled/enabled
smp/core: Use lockdep to assert IRQs are disabled/enabled
timers/hrtimer: Use lockdep to assert IRQs are disabled/enabled
timers/nohz: Use lockdep to assert IRQs are disabled/enabled
workqueue: Use lockdep to assert IRQs are disabled/enabled
irq/softirqs: Use lockdep to assert IRQs are disabled/enabled
locking/lockdep: Add IRQs disabled/enabled assertion APIs: lockdep_assert_irqs_enabled()/disabled()
locking/pvqspinlock: Implement hybrid PV queued/unfair locks
locking/rwlocks: Fix comments
x86/paravirt: Set up the virt_spin_lock_key after static keys get initialized
block, locking/lockdep: Assign a lock_class per gendisk used for wait_for_completion()
workqueue: Remove now redundant lock acquisitions wrt. workqueue flushes
...
The per-cpu counter for init_net is prepared in core_initcall.
The patch 7d720c3e ("percpu: add __percpu sparse annotations to net")
and d6d9ca0fe ("net: this_cpu_xxx conversions") optimize the
routines. Then remove the old counter.
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the TIPC RPS dissector is based only on the incoming packets'
source node address, hence steering all traffic from a node to the same
core. We have seen that this makes the links vulnerable to starvation
and unnecessary resets when we turn down the link tolerance to very low
values.
To reduce the risk of this happening, we exempt probe and probe replies
packets from the convergence to one core per source node. Instead, we do
the opposite, - we try to diverge those packets across as many cores as
possible, by randomizing the flow selector key.
To make such packets identifiable to the dissector, we add a new
'is_keepalive' bit to word 0 of the LINK_PROTOCOL header. This bit is
set both for PROBE and PROBE_REPLY messages, and only for those.
It should be noted that these packets are not part of any flow anyway,
and only constitute a minuscule fraction of all packets sent across a
link. Hence, there is no risk that this will affect overall performance.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we want to gradually implement per netns sysctl_rmem and sysctl_wmem
on per protocol basis, add two new fields in struct proto,
and two new helpers : sk_get_wmem0() and sk_get_rmem0()
First user will be TCP. Then UDP and SCTP can be easily converted,
while DECNET probably wont get this support.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple cases of overlapping changes in the packet scheduler.
Must easier to resolve this time.
Which probably means that I screwed it up somehow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use lockdep to check that IRQs are enabled or disabled as expected. This
way the sanity check only shows overhead when concurrency correctness
debug code is enabled.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/r/1509980490-4285-14-git-send-email-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Timestamps in pktgen are currently retrieved using the deprecated
do_gettimeofday() function that wraps its signed 32-bit seconds in 2038
(on 32-bit architectures) and requires a division operation to calculate
microseconds.
The pktgen header is also defined with the same limitations, hardcoding
to a 32-bit seconds field that can be interpreted as unsigned to produce
times that only wrap in 2106. Whatever code reads the timestamps should
be aware of that problem in general, but probably doesn't care too
much as we are mostly interested in the time passing between packets,
and that is correctly represented.
Using 64-bit nanoseconds would be cheaper and good for 584 years. Using
monotonic times would also make this unambiguous by avoiding the overflow,
but would make it harder to correlate to the times with those on remote
machines. Either approach would require adding a new runtime flag and
implementing the same thing on the remote side, which we probably don't
want to do unless someone sees it as a real problem. Also, this should
be coordinated with other pktgen implementations and might need a new
magic number.
For the moment, I'm documenting the overflow in the source code, and
changing the implementation over to an open-coded ktime_get_real_ts64()
plus division, so we don't have to look at it again while scanning for
deprecated time interfaces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size for IFLA_IF_NETNSID is missing from the size calculation
because the proceeding semicolon was not removed. Fix this by removing
the semicolon.
Detected by CoverityScan, CID#1461135 ("Structurally dead code")
Fixes: 79e1ad148c ("rtnetlink: use netnsid to query interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to the ability to load a program for a specific device,
running verifier twice is no longer needed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the netdev pointer to bpf_prog_get_type(). This way
BPF code can decide whether the device matches what the
code was loaded/translated for.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_xdp is a control path callback for setting up XDP in the
driver. We can reuse it for other forms of communication
between the eBPF stack and the drivers. Rename the callback
and associated structures and definitions.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when an application gets netnsid from the kernel (for example as
the result of RTM_GETLINK call on one end of the veth pair), it's not much
useful. There's no reliable way to get to the netns fd from the netnsid, nor
does any kernel API accept netnsid.
Extend the RTM_GETLINK call to also accept netnsid. It will operate on the
netns with the given netnsid in such case. Of course, the calling process
needs to have enough capabilities in the target name space; for now, require
CAP_NET_ADMIN. This can be relaxed in the future.
To signal to the calling process that the kernel understood the new
IFLA_IF_NETNSID attribute in the query, it will include it in the response.
This is needed to detect older kernels, as they will just ignore
IFLA_IF_NETNSID and query in the current name space.
This patch implemetns IFLA_IF_NETNSID only for get and dump. For set
operations, this can be extended later.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen accidentally used IN6_ADDR_HSIZE, instead of using the size of an
IPv6 address.
Since IN6_ADDR_HSIZE recently was increased from 16 to 256, this old
bug is hitting us.
Fixes: 3f27fb2321 ("ipv6: addrconf: add per netns perturbation in inet6_addr_hash()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When run ipvs in two different network namespace at the same host, and one
ipvs transport network traffic to the other network namespace ipvs.
'ipvs_property' flag will make the second ipvs take no effect. So we should
clear 'ipvs_property' when SKB network namespace changed.
Fixes: 621e84d6f3 ("dev: introduce skb_scrub_packet()")
Signed-off-by: Ye Yin <hustcat@gmail.com>
Signed-off-by: Wei Zhou <chouryzhou@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
In sch_handle_egress and sch_handle_ingress tp->q is used only in order
to update stats. So stats and filter list are the only things that are
needed in clsact qdisc fastpath processing. Introduce new mini_Qdisc
struct to hold those items. Also, introduce a helper to swap the
mini_Qdisc structures in case filter list head changes.
This removes need for tp->q usage without added overhead.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add extack to fib_notifier_info and plumb through stack to
call_fib_rule_notifiers, call_fib_entry_notifiers and
call_fib6_entry_notifiers. This allows notifer handlers to
return messages to user.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_getsockopt bpf call sets the ret variable to zero and
never changes it. What's worse in case CONFIG_INET is
not selected the variable is completely unused generating
a warning.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent additions to support multiple programs in cgroups impose
a strict requirement, "all yes is yes, any no is no". To enforce
this the infrastructure requires the 'no' return code, SK_DROP in
this case, to be 0.
To apply these rules to SK_SKB program types the sk_actions return
codes need to be adjusted.
This fix adds SK_PASS and makes 'SK_DROP = 0'. Finally, remove
SK_ABORTED to remove any chance that the API may allow aborted
program flows to be passed up the stack. This would be incorrect
behavior and allow programs to break existing policies.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB program types use bpf_compute_data to store the end of the
packet data. However, bpf_compute_data assumes the cb is stored in the
qdisc layer format. But, for SK_SKB this is the wrong layer of the
stack for this type.
It happens to work (sort of!) because in most cases nothing happens
to be overwritten today. This is very fragile and error prone.
Fortunately, we have another hole in tcp_skb_cb we can use so lets
put the data_end value there.
Note, SK_SKB program types do not use data_meta, they are failed by
sk_skb_is_valid_access().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After the patch 'rtnetlink: bring NETDEV_CHANGELOWERSTATE event
process back to rtnetlink_event', bond_lower_state_changed would
generate NETDEV_CHANGEUPPER event which would send a notification
to userspace in rtnetlink_event.
There's no need to call rtmsg_ifinfo to send the notification
any more. So this patch is to remove it from these places after
bond_lower_state_changed.
Besides, after this, rtmsg_ifinfo is not needed to be exported.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to bring NETDEV_CHANGELOWERSTATE event process back
to rtnetlink_event so that bonding could use it instead of calling
rtmsg_ifinfo to send a notification to userspace after netdev lower
state is changed in the later patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New tracepoint trace_tcp_send_reset is added and called from
tcp_v4_send_reset(), tcp_v6_send_reset() and tcp_send_active_reset().
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BUG_ON instead of if condition followed by BUG in do_setlink.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for helper function bpf_getsockops to socket_ops BPF
programs. This patch only supports TCP_CONGESTION.
Signed-off-by: Vlad Vysotsky <vlad@cs.ucla.edu>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9cab88726929605 ("net: ethtool: Add back transceiver type")
restores the transceiver type to struct ethtool_link_settings and
convert_link_ksettings_to_legacy_settings() but forgets to remove the
error check for the same in convert_legacy_settings_to_link_ksettings().
This prevents older versions of ethtool to change link settings.
# ethtool --version
ethtool version 3.16
# ethtool -s eth0 autoneg on speed 100 duplex full
Cannot set new settings: Invalid argument
not setting speed
not setting duplex
not setting autoneg
While newer versions of ethtool works.
# ethtool --version
ethtool version 4.10
# ethtool -s eth0 autoneg on speed 100 duplex full
[ 57.703268] sh-eth ee700000.ethernet eth0: Link is Down
[ 59.618227] sh-eth ee700000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx
Fixes: 19cab88726 ("net: ethtool: Add back transceiver type")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Renjith R V <renjith.rv@quest-global.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller stumbled upon a way to trigger
WARNING: CPU: 1 PID: 13881 at net/core/sock_reuseport.c:41
reuseport_alloc+0x306/0x3b0 net/core/sock_reuseport.c:39
There are two initialization paths for the sock_reuseport structure in a
socket: Through the udp/tcp bind paths of SO_REUSEPORT sockets or through
SO_ATTACH_REUSEPORT_[CE]BPF before bind. The existing implementation
assumedthat the socket lock protected both of these paths when it actually
only protects the SO_ATTACH_REUSEPORT path. Syzkaller triggered this
double allocation by running these paths concurrently.
This patch moves the check for double allocation into the reuseport_alloc
function which is protected by a global spin lock.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Fixes: c125e80b88 ("soreuseport: fast reuseport TCP socket selection")
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzkaller hits WARN_ON(sk->sk_wmem_queued) in sk_stream_kill_queues
after triggering an EFAULT in __zerocopy_sg_from_iter.
On this error, skb_zerocopy_stream_iter resets the skb to its state
before the operation with __pskb_trim. It cannot kfree_skb like
datagram callers, as the skb may have data from a previous send call.
__pskb_trim calls skb_condense for unowned skbs, which adjusts their
truesize. These tcp skbuffs are owned and their truesize must add up
to sk_wmem_queued. But they match because their skb->sk is NULL until
tcp_transmit_skb.
Temporarily set skb->sk when calling __pskb_trim to signal that the
skbuffs are owned and avoid the skb_condense path.
Fixes: 52267790ef ("sock: add MSG_ZEROCOPY")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb->mark field is a union with reserved_tailroom which is used
in the TCP code paths from stream memory allocation. Allowing SK_SKB
programs to set this field creates a conflict with future code
optimizations, such as "gifting" the skb to the egress path instead
of creating a new skb and doing a memcpy.
Because we do not have a released version of SK_SKB yet lets just
remove it for now. A more appropriate scratch pad to use at the
socket layer is dev_scratch, but lets add that in future kernels
when needed.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB BPF programs are run from the socket/tcp context but early in
the stack before much of the TCP metadata is needed in tcp_skb_cb. So
we can use some unused fields to place BPF metadata needed for SK_SKB
programs when implementing the redirect function.
This allows us to drop the preempt disable logic. It does however
require an API change so sk_redirect_map() has been updated to
additionally provide ctx_ptr to skb. Note, we do however continue to
disable/enable preemption around actual BPF program running to account
for map updates.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-17
This series contains updates to i40e and ethtool.
Alan provides most of the changes in this series which are mainly fixes
and cleanups. Renamed the ethtool "cmd" variable to "ks", since the new
ethtool API passes us ksettings structs instead of command structs.
Cleaned up an ifdef that was not accomplishing anything. Added function
header comments to provide better documentation. Fixed two issues in
i40e_get_link_ksettings(), by calling
ethtool_link_ksettings_zero_link_mode() to ensure the advertising and
link masks are cleared before we start setting bits. Cleaned up and fixed
code comments which were incorrect. Separated the setting of autoneg in
i40e_phy_types_to_ethtool() into its own conditional to clarify what PHYs
support and advertise autoneg, and makes it easier to add new PHY types in
the future. Added ethtool functionality to intersect two link masks
together to find the common ground between them. Overhauled i40e to
ensure that the new ethtool API macros are being used, instead of the
old ones. Fixed the usage of unsigned 64-bit division which is not
supported on all architectures.
Sudheer adds support for 25G Active Optical Cables (AOC) and Active Copper
Cables (ACC) PHY types.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we are now doing strict checking of what offloads
may access, make sure skb->len is on that list.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the fact that verifier ops are now separate from program
ops to define a separate set of callbacks for verification of
already translated programs.
Since we expect the analyzer ops to be defined only for
a small subset of all program types initialize their array
by hand (don't use linux/bpf_types.h).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bpf_verifier_ops contains both verifier ops and operations
used later during program's lifetime (test_run). Split the runtime
ops into a different structure.
BPF_PROG_TYPE() will now append ## _prog_ops or ## _verifier_ops
to the names.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly for all users of sk_timer.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: linzhang <xiaolou4617@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-x25@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core sk_timer initializer can provide the common .data assignment
instead of it being set separately in users.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: linzhang <xiaolou4617@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-hams@vger.kernel.org
Cc: linux-x25@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes cpumap functional, by adding SKB allocation and
invoking the network stack on the dequeuing CPU.
For constructing the SKB on the remote CPU, the xdp_buff in converted
into a struct xdp_pkt, and it mapped into the top headroom of the
packet, to avoid allocating separate mem. For now, struct xdp_pkt is
just a cpumap internal data structure, with info carried between
enqueue to dequeue.
If a driver doesn't have enough headroom it is simply dropped, with
return code -EOVERFLOW. This will be picked up the xdp tracepoint
infrastructure, to allow users to catch this.
V2: take into account xdp->data_meta
V4:
- Drop busypoll tricks, keeping it more simple.
- Skip RPS and Generic-XDP-recursive-reinjection, suggested by Alexei
V5: correct RCU read protection around __netif_receive_skb_core.
V6: Setting TASK_RUNNING vs TASK_INTERRUPTIBLE based on talk with Rik van Riel
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch connects cpumap to the xdp_do_redirect_map infrastructure.
Still no SKB allocation are done yet. The XDP frames are transferred
to the other CPU, but they are simply refcnt decremented on the remote
CPU. This served as a good benchmark for measuring the overhead of
remote refcnt decrement. If driver page recycle cache is not
efficient then this, exposes a bottleneck in the page allocator.
A shout-out to MST's ptr_ring, which is the secret behind is being so
efficient to transfer memory pointers between CPUs, without constantly
bouncing cache-lines between CPUs.
V3: Handle !CONFIG_BPF_SYSCALL pointed out by kbuild test robot.
V4: Make Generic-XDP aware of cpumap type, but don't allow redirect yet,
as implementation require a separate upstream discussion.
V5:
- Fix a maybe-uninitialized pointed out by kbuild test robot.
- Restrict bpf-prog side access to cpumap, open when use-cases appear
- Implement cpu_map_enqueue() as a more simple void pointer enqueue
V6:
- Allow cpumap type for usage in helper bpf_redirect_map,
general bpf-prog side restriction moved to earlier patch.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function provides a way to intersect two link masks together to
find the common ground between them. For example in i40e, the driver
first generates link masks for what is supported by the PHY type. The
driver then gets the link masks for what the NVM supports. The
resulting intersection between them yields what can truly be supported.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 32302902ff ("mqprio: Reserve last 32 classid values for HW
traffic classes and misc IDs") sch_mqprio started using netdev_txq_to_tc
to find the correct tc instead of dev->tc_to_txq[]
However, when mqprio is compiled as a module, it cannot resolve the
symbol, leading to this error:
ERROR: "netdev_txq_to_tc" [net/sched/sch_mqprio.ko] undefined!
This adds an EXPORT_SYMBOL() since the other user in the kernel
(netif_set_xps_queue) is also EXPORT_SYMBOL() (and not _GPL) or in a
sysfs-callback.
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Henrik Austad <haustad@cisco.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl af_ops currently rely on rtnl mutex: unregister (called from module
exit functions) takes the rtnl mutex and all users that do af_ops lookup
also take the rtnl mutex. IOW, parallel rmmod will block until doit()
callback is done.
As none of the af_ops implementation sleep we can use rcu instead.
doit functions that need the af_ops can now use rcu instead of the
rtnl mutex provided the mutex isn't needed for other reasons.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
next patch will rcu-ify rtnl af_ops, i.e. allow af_ops
lookup and function calls with rcu read lock held instead
of rtnl mutex.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing dev tx_queue_len via netlink or net-sysfs,
a NETDEV_CHANGE_TX_QUEUE_LEN event notification will be
called.
But dev_ioctl missed this event notification, which could
cause no userspace notification would be sent.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
register_netdevice() could fail early when we have an invalid
dev name, in which case ->ndo_uninit() is not called. For tun
device, this is a problem because a timer etc. are already
initialized and it expects ->ndo_uninit() to clean them up.
We could move these initializations into a ->ndo_init() so
that register_netdevice() knows better, however this is still
complicated due to the logic in tun_detach().
Therefore, I choose to just call dev_get_valid_name() before
register_netdevice(), which is quicker and much easier to audit.
And for this specific case, it is already enough.
Fixes: 96442e4242 ("tuntap: choose the txq based on rxq")
Reported-by: Dmitry Alexeev <avekceeb@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_IFALIAS is defined as NLA_STRING. It means that the minimal length of
the attribute is 1 ("\0"). However, to remove an alias, the attribute
length must be 0 (see dev_set_alias()).
Let's define the type to NLA_BINARY to allow 0-length string, so that the
alias can be removed.
Example:
$ ip l s dummy0 alias foo
$ ip l l dev dummy0
5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:20:30:4f:a7:f3 brd ff:ff:ff:ff:ff:ff
alias foo
Before the patch:
$ ip l s dummy0 alias ""
RTNETLINK answers: Numerical result out of range
After the patch:
$ ip l s dummy0 alias ""
$ ip l l dev dummy0
5: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether ae:20:30:4f:a7:f3 brd ff:ff:ff:ff:ff:ff
CC: Oliver Hartkopp <oliver@hartkopp.net>
CC: Stephen Hemminger <stephen@networkplumber.org>
Fixes: 96ca4a2cc1 ("net: remove ifalias on empty given alias")
Reported-by: Julien FLoret <julien.floret@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_CHANGE_TX_QUEUE_LEN event process in rtnetlink_event would
send a notification for userspace and tx_queue_len's setting in
do_setlink would trigger NETDEV_CHANGE_TX_QUEUE_LEN.
So it shouldn't set DO_SETLINK_NOTIFY status for this change to
send a notification any more.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check 'status & DO_SETLINK_NOTIFY' in do_setlink doesn't really
work after status & DO_SETLINK_MODIFIED, as:
DO_SETLINK_MODIFIED 0x1
DO_SETLINK_NOTIFY 0x3
Considering that notifications are suppposed to be sent only when
status have the flag DO_SETLINK_NOTIFY, the right check would be:
(status & DO_SETLINK_NOTIFY) == DO_SETLINK_NOTIFY
This would avoid lots of duplicated notifications when setting some
properties of a link.
Fixes: ba9989069f ("rtnl/do_setlink(): notify when a netdev is modified")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
libteam needs this event notification in userspace when dev's master
dev has been changed. After this, the redundant notifications issue
would be fixed in the later patch 'rtnetlink: check DO_SETLINK_NOTIFY
correctly in do_setlink'.
Fixes: b6b36eb23a ("rtnetlink: Do not generate notifications for NETDEV_CHANGEUPPER event")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As I said in patch 'rtnetlink: bring NETDEV_CHANGEMTU event process back
in rtnetlink_event', removing NETDEV_POST_TYPE_CHANGE event was not the
right fix for the redundant notifications issue.
So bring this event process back to rtnetlink_event and the old redundant
notifications issue would be fixed in the later patch 'rtnetlink: check
DO_SETLINK_NOTIFY correctly in do_setlink'.
Fixes: aef091ae58 ("rtnetlink: Do not generate notifications for POST_TYPE_CHANGE event")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same fix for changing mtu in the patch 'rtnetlink: bring
NETDEV_CHANGEMTU event process back in rtnetlink_event' is
needed for changing tx_queue_len.
Note that the redundant notifications issue for tx_queue_len
will be fixed in the later patch 'rtnetlink: do not send
notification for tx_queue_len in do_setlink'.
Fixes: 27b3b551d8 ("rtnetlink: Do not generate notifications for NETDEV_CHANGE_TX_QUEUE_LEN event")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 085e1a65f0 ("rtnetlink: Do not generate notifications for MTU
events") tried to fix the redundant notifications issue when ip link
set mtu by removing NETDEV_CHANGEMTU event process in rtnetlink_event.
But it also resulted in no notification generated when dev's mtu is
changed via other methods, like:
'ifconfig eth1 mtu 1400' or 'echo 1400 > /sys/class/net/eth1/mtu'
It would cause users not to be notified by this change.
This patch is to fix it by bringing NETDEV_CHANGEMTU event back into
rtnetlink_event, and the redundant notifications issue will be fixed
in the later patch 'rtnetlink: check DO_SETLINK_NOTIFY correctly in
do_setlink'.
Fixes: 085e1a65f0 ("rtnetlink: Do not generate notifications for MTU events")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a real-time notification for tcp retransmission
for monitoring.
Of course we could use ftrace to dynamically instrument this
kernel function too, however we can't retrieve the connection
information at the same time, for example perf-tools [1] reads
/proc/net/tcp for socket details, which is slow when we have
a lots of connections.
Therefore, this patch adds a tracepoint for __tcp_retransmit_skb()
and exposes src/dst IP addresses and ports of the connection.
This also makes it easier to integrate into perf.
Note, I expose both IPv4 and IPv6 addresses at the same time:
for a IPv4 socket, v4 mapped address is used as IPv6 addresses,
for a IPv6 socket, LOOPBACK4_IPV6 is already filled by kernel.
Also, add sk and skb pointers as they are useful for BPF.
1. https://github.com/brendangregg/perf-tools/blob/master/net/tcpretrans
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Brendan Gregg <bgregg@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If for some reason, the newly allocated child need to be freed,
we will call cgroup_put() (via sk_free_unlock_clone()) while the
corresponding cgroup_get() was not yet done, and we will free memory
too soon.
Fixes: d979a39d72 ("cgroup: duplicate cgroup reference when cloning sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fbb1fb4ad4.
This was not the proper fix, lets cleanly revert it, so that
following patch can be carried to stable versions.
sock_cgroup_ptr() callers do not expect a NULL return value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_DST_CACHE is not selected cpu variable
will be unused and we will see a compilation warning.
Move it under the ifdef.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: d66f2b91f9 ("bpf: don't rely on the verifier lock for metadata_dst allocation")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can now piggyback error strings to userspace via extended acks
rather than using printk.
Before:
bridge fdb add 01:02:03:04:05:06 dev br0 vlan 4095
RTNETLINK answers: Invalid argument
After:
bridge fdb add 01:02:03:04:05:06 dev br0 vlan 4095
Error: invalid vlan id.
v3: drop 'RTM_' prefixes, suggested by David Ahern, they
are not useful, the add/del in bridge command line is enough.
Also reword error in response to malformed/bad vlan id attribute
size.
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix BUG() calls to use BUG_ON(conditional) macros.
This was found using make coccicheck M=net/core on linux next
tag next-2017092
Signed-off-by: Tim Hansen <devtimhansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_skb_set_tunnel_*() functions require allocation of per-cpu
metadata_dst. The allocation happens upon verification of the
first program using those helpers. In preparation for removing
the verifier lock, use cmpxchg() to make sure we only allocate
the metadata_dsts once.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_clone_lock() might run while TCP/DCCP listener already vanished.
In order to prevent use after free, it is better to defer cgroup_sk_alloc()
to the point we know both parent and child exist, and from process context.
Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of calling mem_cgroup_sk_alloc() from BH context,
it is better to call it from inet_csk_accept() in process context.
Not only this removes code in mem_cgroup_sk_alloc(), but it also
fixes a bug since listener might have been dismantled and css_get()
might cause a use-after-free.
Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack arg to netdev_upper_dev_link and netdev_master_upper_dev_link
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack to do_set_master and down to ndo_add_slave
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink_ext_ack to netdev_notifier_info to allow notifier
handlers to return errors to userspace.
Clean up the initialization in dev.c such that extack is easily
added in subsequent patches where relevant. Specifically, remove
the init call in call_netdevice_notifiers_info and have callers
initalize on stack when info is declared.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
x-netns interfaces are bound to two netns: the link netns and the upper
netns. Usually, this kind of interfaces is created in the link netns and
then moved to the upper netns. At the end, the interface is visible only
in the upper netns. The link nsid is advertised via netlink in the upper
netns, thus the user always knows where is the link part.
There is no such mechanism in the link netns. When the interface is moved
to another netns, the user cannot "follow" it.
This patch adds a new netlink attribute which helps to follow an interface
which moves to another netns. When the interface is unregistered, the new
nsid is advertised. If the interface is a x-netns interface (ie
rtnl_link_ops->get_link_net is defined), the nsid is allocated if needed.
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compiler does not really know that skb_shinfo(to|from) are constants
in skb_try_coalesce(), lets cache their values to shrink code.
We might even take care of skb_zcopy() calls later.
$ size net/core/skbuff.o.before net/core/skbuff.o
text data bss dec hex filename
40727 1298 0 42025 a429 net/core/skbuff.o.before
40631 1298 0 41929 a3c9 net/core/skbuff.o
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
no users in the tree.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/dev.c:1306: warning: No description found for parameter 'name'
net/core/dev.c:1306: warning: Excess function parameter 'alias' description in 'dev_get_alias'
Fixes: 6c5570016b ("net: core: decouple ifalias get/set from rtnl lock")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device alias can be set by either rtnetlink (rtnl is held) or sysfs.
rtnetlink hold the rtnl mutex, sysfs acquires it for this purpose.
Add an extra mutex for it and use rcu to protect concurrent accesses.
This allows the sysfs path to not take rtnl and would later allow
to not hold it when dumping ifalias.
Based on suggestion from Eric Dumazet.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RTM_GETSTATS was added the fields of its header struct were not all
initialized when returning the result thus leaking 4 bytes of information
to user-space per rtnl_fill_statsinfo call, so initialize them now. Thanks
to Alexander Potapenko for the detailed report and bisection.
Reported-by: Alexander Potapenko <glider@google.com>
Fixes: 10c9ead9f3 ("rtnetlink: add new RTM_GETSTATS message to dump link stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from linux-4.4, 3WHS no longer takes the listener lock.
Since this time, we might hit a use-after-free in sk_filter_charge(),
if the filter we got in the memcpy() of the listener content
just happened to be replaced by a thread changing listener BPF filter.
To fix this, we need to make sure the filter refcount is not already
zero before incrementing it again.
Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move dissection of tunnel info from the flower classifier to the flow
dissector where all other dissection occurs. This should not have any
behavioural affect on other users of the flow dissector.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_prot and sk->sk_prot_creator can differ when the app uses
IPV6_ADDRFORM (transforming an IPv6-socket to an IPv4-one).
Which is why sk_prot_creator is there to make sure that sk_prot_free()
does the kmem_cache_free() on the right kmem_cache slab.
Now, if such a socket gets transformed back to a listening socket (using
connect() with AF_UNSPEC) we will allocate an IPv4 tcp_sock through
sk_clone_lock() when a new connection comes in. But sk_prot_creator will
still point to the IPv6 kmem_cache (as everything got copied in
sk_clone_lock()). When freeing, we will thus put this
memory back into the IPv6 kmem_cache although it was allocated in the
IPv4 cache. I have seen memory corruption happening because of this.
With slub-debugging and MEMCG_KMEM enabled this gives the warning
"cache_from_obj: Wrong slab cache. TCPv6 but object is from TCP"
A C-program to trigger this:
void main(void)
{
int fd = socket(AF_INET6, SOCK_STREAM, IPPROTO_TCP);
int new_fd, newest_fd, client_fd;
struct sockaddr_in6 bind_addr;
struct sockaddr_in bind_addr4, client_addr1, client_addr2;
struct sockaddr unsp;
int val;
memset(&bind_addr, 0, sizeof(bind_addr));
bind_addr.sin6_family = AF_INET6;
bind_addr.sin6_port = ntohs(42424);
memset(&client_addr1, 0, sizeof(client_addr1));
client_addr1.sin_family = AF_INET;
client_addr1.sin_port = ntohs(42424);
client_addr1.sin_addr.s_addr = inet_addr("127.0.0.1");
memset(&client_addr2, 0, sizeof(client_addr2));
client_addr2.sin_family = AF_INET;
client_addr2.sin_port = ntohs(42421);
client_addr2.sin_addr.s_addr = inet_addr("127.0.0.1");
memset(&unsp, 0, sizeof(unsp));
unsp.sa_family = AF_UNSPEC;
bind(fd, (struct sockaddr *)&bind_addr, sizeof(bind_addr));
listen(fd, 5);
client_fd = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP);
connect(client_fd, (struct sockaddr *)&client_addr1, sizeof(client_addr1));
new_fd = accept(fd, NULL, NULL);
close(fd);
val = AF_INET;
setsockopt(new_fd, SOL_IPV6, IPV6_ADDRFORM, &val, sizeof(val));
connect(new_fd, &unsp, sizeof(unsp));
memset(&bind_addr4, 0, sizeof(bind_addr4));
bind_addr4.sin_family = AF_INET;
bind_addr4.sin_port = ntohs(42421);
bind(new_fd, (struct sockaddr *)&bind_addr4, sizeof(bind_addr4));
listen(new_fd, 5);
client_fd = socket(AF_INET, SOCK_STREAM, IPPROTO_TCP);
connect(client_fd, (struct sockaddr *)&client_addr2, sizeof(client_addr2));
newest_fd = accept(new_fd, NULL, NULL);
close(new_fd);
close(client_fd);
close(new_fd);
}
As far as I can see, this bug has been there since the beginning of the
git-days.
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it can be switched to rcu.
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
similar to earlier patches, split out more parts of this function to
better see what is happening and where we assume rtnl is locked.
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtnl_fill_ifinfo currently requires caller to hold the rtnl mutex.
Unfortunately the function is quite large which makes it harder to see
which spots require the lock, which spots assume it and which ones could
do without.
Add helpers to factor out the ifindex dumping, one can use rcu to avoid
rtnl dependency.
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.
xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.
The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just do the rename into bpf_compute_data_pointers() as we'll add
one more pointer here to recompute.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Key length can't be negative.
Leave comparisons against nla_len() signed just in case truncated attribute
can sneak in there.
Space savings:
add/remove: 0/0 grow/shrink: 0/7 up/down: 0/-7 (-7)
function old new delta
pneigh_delete 273 272 -1
mlx5e_rep_netevent_event 1415 1414 -1
mlx5e_create_encap_header_ipv6 1194 1193 -1
mlx5e_create_encap_header_ipv4 1071 1070 -1
cxgb4_l2t_get 1104 1103 -1
__pneigh_lookup 69 68 -1
__neigh_create 2452 2451 -1
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As measured in my prior patch ("sch_netem: faster rb tree removal"),
rbtree_postorder_for_each_entry_safe() is nice looking but much slower
than using rb_next() directly, except when tree is small enough
to fit in CPU caches (then the cost is the same)
Also note that there is not even an increase of text size :
$ size net/core/skbuff.o.before net/core/skbuff.o
text data bss dec hex filename
40711 1298 0 42009 a419 net/core/skbuff.o.before
40711 1298 0 42009 a419 net/core/skbuff.o
From: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Private part of allocation is never big enough to warrant size_t.
Space savings:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-10 (-10)
function old new delta
alloc_netdev_mqs 1120 1110 -10
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zerocopy skbs frags are copied when the skb is looped to a local sock.
Commit 1080e512d4 ("net: orphan frags on receive") introduced calls
to skb_orphan_frags to deliver_skb and __netif_receive_skb for this.
With msg_zerocopy, these skbs can also exist in the tx path and thus
loop from dev_queue_xmit_nit. This already calls deliver_skb in its
loop. But it does not orphan before a separate pt_prev->func().
Add the missing skb_orphan_frags_rx.
Changes
v1->v2: handle skb_orphan_frags_rx failure
Fixes: 1f8b977ab3 ("sock: enable MSG_ZEROCOPY")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
deprecated the ethtool_cmd::transceiver field, which was fine in
premise, except that the PHY library was actually using it to report the
type of transceiver: internal or external.
Use the first word of the reserved field to put this __u8 transceiver
field back in. It is made read-only, and we don't expect the
ETHTOOL_xLINKSETTINGS API to be doing anything with this anyway, so this
is mostly for the legacy path where we do:
ethtool_get_settings()
-> dev->ethtool_ops->get_link_ksettings()
-> convert_link_ksettings_to_legacy_settings()
to have no information loss compared to the legacy get_settings API.
Fixes: 3f1ac7a700 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since XDP's view of the packet includes the MAC header, moving the start-
of-packet with bpf_xdp_adjust_head needs to also update the offset of the
MAC header (which is relative to skb->head, not to the skb->data that was
changed).
Without this, tcpdump sees packets starting from the old MAC header rather
than the new one, at least in my tests on the loopback device.
Fixes: b5cdae3291 ("net: Generic XDP")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 109980b894 ("bpf: don't select potentially stale
ri->map from buggy xdp progs") passed the pointer to the prog
itself to be loaded into r4 prior on bpf_redirect_map() helper
call, so that we can store the owner into ri->map_owner out of
the helper.
Issue with that is that the actual address of the prog is still
subject to change when subsequent rewrites occur that require
slow path in bpf_prog_realloc() to alloc more memory, e.g. from
patching inlining helper functions or constant blinding. Thus,
we really need to take prog->aux as the address we're holding,
which also works with prog clones as they share the same aux
object.
Instead of then fetching aux->prog during runtime, which could
potentially incur cache misses due to false sharing, we are
going to just use aux for comparison on the map owner. This
will also keep the patchlet of the same size, and later check
in xdp_map_invalid() only accesses read-only aux pointer from
the prog, it's also in the same cacheline already from prior
access when calling bpf_func.
Fixes: 109980b894 ("bpf: don't select potentially stale ri->map from buggy xdp progs")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denys reported wrong rate estimations with HTB classes.
It appears the bug was added in linux-4.10, since my tests
where using intervals of one second only.
HTB using 4 sec default rate estimators, reported rates
were 4x higher.
We need to properly scale the bytes/packets samples before
integrating them in EWMA.
Tested:
echo 1 >/sys/module/sch_htb/parameters/htb_rate_est
Setup HTB with one class with a rate/cail of 5Gbit
Generate traffic on this class
tc -s -d cl sh dev eth0 classid 7002:11
class htb 7002:11 parent 7002:1 prio 5 quantum 200000 rate 5Gbit ceil
5Gbit linklayer ethernet burst 80000b/1 mpu 0b cburst 80000b/1 mpu 0b
level 0 rate_handle 1
Sent 1488215421648 bytes 982969243 pkt (dropped 0, overlimits 0
requeues 0)
rate 5Gbit 412814pps backlog 136260b 2p requeues 0
TCP pkts/rtx 982969327/45 bytes 1488215557414/68130
lended: 22732826 borrowed: 0 giants: 0
tokens: -1684 ctokens: -1684
Fixes: 1c0d32fde5 ("net_sched: gen_estimator: complete rewrite of rate estimators")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using bpf_redirect_map is allowed for generic XDP programs, but the
appropriate map lookup was never performed in xdp_do_generic_redirect().
Instead the map-index is directly used as the ifindex. For the
xdp_redirect_map sample in SKB-mode '-S', this resulted in trying
sending on ifindex 0 which isn't valid, resulting in getting SKB
packets dropped. Thus, the reported performance numbers are wrong in
commit 24251c2647 ("samples/bpf: add option for native and skb mode
for redirect apps") for the 'xdp_redirect_map -S' case.
Before commit 109980b894 ("bpf: don't select potentially stale
ri->map from buggy xdp progs") it could crash the kernel. Like this
commit also check that the map_owner owner is correct before
dereferencing the map pointer. But make sure that this API misusage
can be caught by a tracepoint. Thus, allowing userspace via
tracepoints to detect misbehaving bpf_progs.
Fixes: 6103aa96ec ("net: implement XDP_REDIRECT for xdp generic")
Fixes: 24251c2647 ("samples/bpf: add option for native and skb mode for redirect apps")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"The iwlwifi firmware compat fix is in here as well as some other
stuff:
1) Fix request socket leak introduced by BPF deadlock fix, from Eric
Dumazet.
2) Fix VLAN handling with TXQs in mac80211, from Johannes Berg.
3) Missing __qdisc_drop conversions in prio and qfq schedulers, from
Gao Feng.
4) Use after free in netlink nlk groups handling, from Xin Long.
5) Handle MTU update properly in ipv6 gre tunnels, from Xin Long.
6) Fix leak of ipv6 fib tables on netns teardown, from Sabrina Dubroca
with follow-on fix from Eric Dumazet.
7) Need RCU and preemption disabled during generic XDP data patch,
from John Fastabend"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
bpf: make error reporting in bpf_warn_invalid_xdp_action more clear
Revert "mdio_bus: Remove unneeded gpiod NULL check"
bpf: devmap, use cond_resched instead of cpu_relax
bpf: add support for sockmap detach programs
net: rcu lock and preempt disable missing around generic xdp
bpf: don't select potentially stale ri->map from buggy xdp progs
net: tulip: Constify tulip_tbl
net: ethernet: ti: netcp_core: no need in netif_napi_del
davicom: Display proper debug level up to 6
net: phy: sfp: rename dt properties to match the binding
dt-binding: net: sfp binding documentation
dt-bindings: add SFF vendor prefix
dt-bindings: net: don't confuse with generic PHY property
ip6_tunnel: fix setting hop_limit value for ipv6 tunnel
ip_tunnel: fix setting ttl and tos value in collect_md mode
ipv6: fix typo in fib6_net_exit()
tcp: fix a request socket leak
sctp: fix missing wake ups in some situations
netfilter: xt_hashlimit: fix build error caused by 64bit division
netfilter: xt_hashlimit: alloc hashtable with right size
...
Differ between illegal XDP action code and just driver
unsupported one to provide better feedback when we throw
a one-time warning here. Reason is that with 814abfabef
("xdp: add bpf_redirect helper function") not all drivers
support the new XDP return code yet and thus they will
fall into their 'default' case when checking for return
codes after program return, which then triggers a
bpf_warn_invalid_xdp_action() stating that the return
code is illegal, but from XDP perspective it's not.
I decided not to place something like a XDP_ACT_MAX define
into uapi i) given we don't have this either for all other
program types, ii) future action codes could have further
encoding there, which would render such define unsuitable
and we wouldn't be able to rip it out again, and iii) we
rarely add new action codes.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
do_xdp_generic must be called inside rcu critical section with preempt
disabled to ensure BPF programs are valid and per-cpu variables used
for redirect operations are consistent. This patch ensures this is true
and fixes the splat below.
The netif_receive_skb_internal() code path is now broken into two rcu
critical sections. I decided it was better to limit the preempt_enable/disable
block to just the xdp static key portion and the fallout is more
rcu_read_lock/unlock calls. Seems like the best option to me.
[ 607.596901] =============================
[ 607.596906] WARNING: suspicious RCU usage
[ 607.596912] 4.13.0-rc4+ #570 Not tainted
[ 607.596917] -----------------------------
[ 607.596923] net/core/dev.c:3948 suspicious rcu_dereference_check() usage!
[ 607.596927]
[ 607.596927] other info that might help us debug this:
[ 607.596927]
[ 607.596933]
[ 607.596933] rcu_scheduler_active = 2, debug_locks = 1
[ 607.596938] 2 locks held by pool/14624:
[ 607.596943] #0: (rcu_read_lock_bh){......}, at: [<ffffffff95445ffd>] ip_finish_output2+0x14d/0x890
[ 607.596973] #1: (rcu_read_lock_bh){......}, at: [<ffffffff953c8e3a>] __dev_queue_xmit+0x14a/0xfd0
[ 607.597000]
[ 607.597000] stack backtrace:
[ 607.597006] CPU: 5 PID: 14624 Comm: pool Not tainted 4.13.0-rc4+ #570
[ 607.597011] Hardware name: Dell Inc. Precision Tower 5810/0HHV7N, BIOS A17 03/01/2017
[ 607.597016] Call Trace:
[ 607.597027] dump_stack+0x67/0x92
[ 607.597040] lockdep_rcu_suspicious+0xdd/0x110
[ 607.597054] do_xdp_generic+0x313/0xa50
[ 607.597068] ? time_hardirqs_on+0x5b/0x150
[ 607.597076] ? mark_held_locks+0x6b/0xc0
[ 607.597088] ? netdev_pick_tx+0x150/0x150
[ 607.597117] netif_rx_internal+0x205/0x3f0
[ 607.597127] ? do_xdp_generic+0xa50/0xa50
[ 607.597144] ? lock_downgrade+0x2b0/0x2b0
[ 607.597158] ? __lock_is_held+0x93/0x100
[ 607.597187] netif_rx+0x119/0x190
[ 607.597202] loopback_xmit+0xfd/0x1b0
[ 607.597214] dev_hard_start_xmit+0x127/0x4e0
Fixes: d445516966 ("net: xdp: support xdp generic on virtual devices")
Fixes: b5cdae3291 ("net: Generic XDP")
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can potentially run into a couple of issues with the XDP
bpf_redirect_map() helper. The ri->map in the per CPU storage
can become stale in several ways, mostly due to misuse, where
we can then trigger a use after free on the map:
i) prog A is calling bpf_redirect_map(), returning XDP_REDIRECT
and running on a driver not supporting XDP_REDIRECT yet. The
ri->map on that CPU becomes stale when the XDP program is unloaded
on the driver, and a prog B loaded on a different driver which
supports XDP_REDIRECT return code. prog B would have to omit
calling to bpf_redirect_map() and just return XDP_REDIRECT, which
would then access the freed map in xdp_do_redirect() since not
cleared for that CPU.
ii) prog A is calling bpf_redirect_map(), returning a code other
than XDP_REDIRECT. prog A is then detached, which triggers release
of the map. prog B is attached which, similarly as in i), would
just return XDP_REDIRECT without having called bpf_redirect_map()
and thus be accessing the freed map in xdp_do_redirect() since
not cleared for that CPU.
iii) prog A is attached to generic XDP, calling the bpf_redirect_map()
helper and returning XDP_REDIRECT. xdp_do_generic_redirect() is
currently not handling ri->map (will be fixed by Jesper), so it's
not being reset. Later loading a e.g. native prog B which would,
say, call bpf_xdp_redirect() and then returns XDP_REDIRECT would
find in xdp_do_redirect() that a map was set and uses that causing
use after free on map access.
Fix thus needs to avoid accessing stale ri->map pointers, naive
way would be to call a BPF function from drivers that just resets
it to NULL for all XDP return codes but XDP_REDIRECT and including
XDP_REDIRECT for drivers not supporting it yet (and let ri->map
being handled in xdp_do_generic_redirect()). There is a less
intrusive way w/o letting drivers call a reset for each BPF run.
The verifier knows we're calling into bpf_xdp_redirect_map()
helper, so it can do a small insn rewrite transparent to the prog
itself in the sense that it fills R4 with a pointer to the own
bpf_prog. We have that pointer at verification time anyway and
R4 is allowed to be used as per calling convention we scratch
R0 to R5 anyway, so they become inaccessible and program cannot
read them prior to a write. Then, the helper would store the prog
pointer in the current CPUs struct redirect_info. Later in
xdp_do_*_redirect() we check whether the redirect_info's prog
pointer is the same as passed xdp_prog pointer, and if that's
the case then all good, since the prog holds a ref on the map
anyway, so it is always valid at that point in time and must
have a reference count of at least 1. If in the unlikely case
they are not equal, it means we got a stale pointer, so we clear
and bail out right there. Also do reset map and the owning prog
in bpf_xdp_redirect(), so that bpf_xdp_redirect_map() and
bpf_xdp_redirect() won't get mixed up, only the last call should
take precedence. A tc bpf_redirect() doesn't use map anywhere
yet, so no need to clear it there since never accessed in that
layer.
Note that in case the prog is released, and thus the map as
well we're still under RCU read critical section at that time
and have preemption disabled as well. Once we commit with the
__dev_map_insert_ctx() from xdp_do_redirect_map() and set the
map to ri->map_to_flush, we still wait for a xdp_do_flush_map()
to finish in devmap dismantle time once flush_needed bit is set,
so that is fine.
Fixes: 97f91a7cf0 ("bpf: add bpf_redirect_map helper routine")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 0ddf3fb2c4 ("udp: preserve skb->dst if required
for IP options processing") we clear the skb head state as soon
as the skb carrying them is first processed.
Since the same skb can be processed several times when MSG_PEEK
is used, we can end up lacking the required head states, and
eventually oopsing.
Fix this clearing the skb head state only when processing the
last skb reference.
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 0ddf3fb2c4 ("udp: preserve skb->dst if required for IP options processing")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull cgroup updates from Tejun Heo:
"Several notable changes this cycle:
- Thread mode was merged. This will be used for cgroup2 support for
CPU and possibly other controllers. Unfortunately, CPU controller
cgroup2 support didn't make this pull request but most contentions
have been resolved and the support is likely to be merged before
the next merge window.
- cgroup.stat now shows the number of descendant cgroups.
- cpuset now can enable the easier-to-configure v2 behavior on v1
hierarchy"
* 'for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (21 commits)
cpuset: Allow v2 behavior in v1 cgroup
cgroup: Add mount flag to enable cpuset to use v2 behavior in v1 cgroup
cgroup: remove unneeded checks
cgroup: misc changes
cgroup: short-circuit cset_cgroup_from_root() on the default hierarchy
cgroup: re-use the parent pointer in cgroup_destroy_locked()
cgroup: add cgroup.stat interface with basic hierarchy stats
cgroup: implement hierarchy limits
cgroup: keep track of number of descent cgroups
cgroup: add comment to cgroup_enable_threaded()
cgroup: remove unnecessary empty check when enabling threaded mode
cgroup: update debug controller to print out thread mode information
cgroup: implement cgroup v2 thread support
cgroup: implement CSS_TASK_ITER_THREADED
cgroup: introduce cgroup->dom_cgrp and threaded css_set handling
cgroup: add @flags to css_task_iter_start() and implement CSS_TASK_ITER_PROCS
cgroup: reorganize cgroup.procs / task write path
cgroup: replace css_set walking populated test with testing cgrp->nr_populated_csets
cgroup: distinguish local and children populated states
cgroup: remove now unused list_head @pending in cgroup_apply_cftypes()
...
In flow dissector there are no limits to the number of nested
encapsulations or headers that might be dissected which makes for a
nice DOS attack. This patch sets a limit of the number of headers
that flow dissector will parse.
Headers includes network layer headers, transport layer headers, shim
headers for encapsulation, IPv6 extension headers, etc. The limit for
maximum number of headers to parse has be set to fifteen to account for
a reasonable number of encapsulations, extension headers, VLAN,
in a packet. Note that this limit does not supercede the STOP_AT_*
flags which may stop processing before the headers limit is reached.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
__skb_flow_dissect is riddled with gotos that make discerning the flow,
debugging, and extending the capability difficult. This patch
reorganizes things so that we only perform goto's after the two main
switch statements (no gotos within the cases now). It also eliminates
several goto labels so that there are only two labels that can be target
for goto.
Reported-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a listener registers to the FIB notification chain it receives a
dump of the FIB entries and rules from existing address families by
invoking their dump operations.
While we call into these modules we need to make sure they aren't
removed. Do that by increasing their reference count before invoking
their dump operations and decrease it afterwards.
Fixes: 04b1d4e50e ("net: core: Make the FIB notification chain generic")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
v2: added the change in drivers/vhost/net.c as spotted
by Willem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to convert this atomic_t refcnt to refcount_t,
we need to init the refcount to one to not trigger
a 0 -> 1 transition.
This also removes one atomic operation in fast path.
v2: removed dead code in sock_zerocopy_put_abort()
as suggested by Willem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sock_filter_is_valid_access consistent with other is_valid_access
helpers.
Requested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.
Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.
One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.
Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nogah Frankel <nogahf@mellanox.com>
Tested-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow BPF programs run on sock create to use the get_current_uid_gid
helper. IPv4 and IPv6 sockets are created in a process context so
there is always a valid uid/gid
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add socket mark and priority to fields that can be set by
ebpf program when a socket is created.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the IPv6 host table which will be introduced in the
following patches. The fields in the header are added per-use. This header
is global and can be reused by many drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends bridge fdb table tracepoints to also cover
learned fdb entries in the br_fdb_update path. Note that
unlike other tracepoints I have moved this to when the fdb
is modified because this is in the datapath and can generate
a lot of noise in the trace output. br_fdb_update is also called
from added_by_user context in the NTF_USE case which is already
traced ..hence the !added_by_user check.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 name uses "destination ip" as does the IPv6 patch set.
Make the mac field consistent.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian reported UDP xmit drops that could be root caused to the
too small neigh limit.
Current limit is 64 KB, meaning that even a single UDP socket would hit
it, since its default sk_sndbuf comes from net.core.wmem_default
(~212992 bytes on 64bit arches).
Once ARP/ND resolution is in progress, we should allow a little more
packets to be queued, at least for one producer.
Once neigh arp_queue is filled, a rogue socket should hit its sk_sndbuf
limit and either block in sendmsg() or return -EAGAIN.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few useful tracepoints to trace bridge forwarding
database updates.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating as specific xdp_redirect_map variant of the xdp tracepoints
allow users to write simpler/faster BPF progs that get attached to
these tracepoints.
Goal is to still keep the tracepoints in xdp_redirect and xdp_redirect_map
similar enough, that a tool can read the top part of the TP_STRUCT and
produce similar monitor statistics.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a need to separate the xdp_redirect tracepoint into two
tracepoints, for separating the error case from the normal forward
case.
Due to the extreme speeds XDP is operating at, loading a tracepoint
have a measurable impact. Single core XDP REDIRECT (ethtool tuned
rx-usecs 25) can do 13.7 Mpps forwarding, but loading a simple
bpf_prog at the tracepoint (with a return 0) reduce perf to 10.2 Mpps
(CPU E5-1650 v4 @ 3.60GHz, driver: ixgbe)
The overhead of loading a bpf-based tracepoint can be calculated to
cost 25 nanosec ((1/13782002-1/10267937)*10^9 = -24.83 ns).
Using perf record on the tracepoint event, with a non-matching --filter
expression, the overhead is much larger. Performance drops to 8.3 Mpps,
cost 48 nanosec ((1/13782002-1/8312497)*10^9 = -47.74))
Having a separate tracepoint for err cases, which should be less
frequent, allow running a continuous monitor for errors while not
affecting the redirect forward performance (this have also been
verified by measurements).
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make sense of the map index, the tracepoint user also need to know
that map we are talking about. Supply the map pointer but only expose
the map->id.
The 'to_index' is renamed 'to_ifindex'. In the xdp_redirect_map case,
this is the result of the devmap lookup. The map lookup key is exposed
as map_index, which is needed to troubleshoot in case the lookup failed.
The 'to_ifindex' is placed after 'err' to keep TP_STRUCT as common as
possible.
This also keeps the TP_STRUCT similar enough, that userspace can write
a monitor program, that doesn't need to care about whether
bpf_redirect or bpf_redirect_map were used.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supplying the action argument XDP_REDIRECT to the tracepoint xdp_redirect
is redundant as it is only called in-case this action was specified.
Remove the argument, but keep "act" member of the tracepoint struct and
populate it with XDP_REDIRECT. This makes it easier to write a common bpf_prog
processing events.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that busy_poll_stop() also invoke the drivers napi->poll()
function pointer, but didn't have an associated call to trace_napi_poll()
like all other call sites.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few bugs around refcnt handling in the new BPF congestion
control setsockopt:
- The new ca is assigned to icsk->icsk_ca_ops even in the case where we
cannot get a reference on it. This would lead to a use after free,
since that ca is going away soon.
- Changing the congestion control case doesn't release the refcnt on
the previous ca.
- In the reinit case, we first leak a reference on the old ca, then we
call tcp_reinit_congestion_control on the ca that we have just
assigned, leading to deinitializing the wrong ca (->release of the
new ca on the old ca's data) and releasing the refcount on the ca
that we actually want to use.
This is visible by building (for example) BIC as a module and setting
net.ipv4.tcp_congestion_control=bic, and using tcp_cong_kern.c from
samples/bpf.
This patch fixes the refcount issues, and moves reinit back into tcp
core to avoid passing a ca pointer back to BPF.
Fixes: 91b5b21c7c ("bpf: Add support for changing congestion control")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug causing any sock operations to always return EINVAL.
Fixes: a5192c5237 ("bpf: fix to bpf_setsockops").
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Craig Gallek <kraig@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is too much overhead in the current trace_xdp_redirect
tracepoint as it does strcpy and strlen on the net_device names.
Besides, exposing the ifindex/index is actually the information that
is needed in the tracepoint to diagnose issues. When a lookup fails
(either ifindex or devmap index) then there is a need for saying which
to_index that have issues.
V2: Adjust args to be aligned with trace_xdp_exception.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the xdp_do_generic_redirect() call fails, it trigger the
trace_xdp_exception tracepoint. It seems better to use the same
tracepoint trace_xdp_redirect, as the native xdp_do_redirect{,_map} does.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given there is a tracepoint that can track the error code
of xdp_do_redirect calls, the WARN_ONCE in bpf_warn_invalid_xdp_redirect
doesn't seem relevant any longer. Simply remove the function.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The entry clear routine can be shared between the drivers, thus it is
moved inside devlink.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the dpipe table's size was static and known at registration
time. The host table does not have constant size and it is resized in
dynamic manner. In order to support this behavior the size is changed
to be obtained dynamically via an op.
This patch also adjust the current dpipe table for the new API.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the IPv4 host table which will be introduced in the
following patches. This header is global and can be reused by many
drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the IPv4 host table which will be introduced in the
following patches. This header is global and can be reused by many
drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary to allow the user to disable peeking with
offset once it's enabled.
Unix sockets already allow the above, with this patch we
permit it for udp[6] sockets, too.
Fixes: 627d2d6b55 ("udp: enable MSG_PEEK at non-zero offset")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename skb_pad() into __skb_pad() and make it take a third argument:
free_on_error which controls whether kfree_skb() should be called or
not, skb_pad() directly makes use of it and passes true to preserve its
existing behavior. Do exactly the same thing with __skb_put_padto() and
skb_put_padto().
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few cleanups including: bpf_redirect_map() is really XDP only due to
the return code. Move it to a more appropriate location where we do
the XDP redirect handling and change it's name into bpf_xdp_redirect_map()
to make it consistent to the bpf_xdp_redirect() helper.
xdp_do_redirect_map() helper can be static since only used out of filter.c
file. Drop the goto in xdp_do_generic_redirect() and only return errors
directly. In xdp_do_flush_map() only clear ri->map_to_flush which is the
arg we're using in that function, ri->map is cleared earlier along with
ri->ifindex.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When peeking, if a bad csum is discovered, the skb is unlinked from
the queue with __sk_queue_drop_skb and the peek operation restarted.
__sk_queue_drop_skb only drops packets that match the queue head.
This fails if the skb was found after the head, using SO_PEEK_OFF
socket option. This causes an infinite loop.
We MUST drop this problematic skb, and we can simply check if skb was
already removed by another thread, by looking at skb->next :
This pointer is set to NULL by the __skb_unlink() operation, that might
have happened only under the spinlock protection.
Many thanks to syzkaller team (and particularly Dmitry Vyukov who
provided us nice C reproducers exhibiting the lockup) and Willem de
Bruijn who provided first version for this patch and a test program.
Fixes: 627d2d6b55 ("udp: enable MSG_PEEK at non-zero offset")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3fcece12bc ("net: store port/representator id in metadata_dst")
added a new type field to metadata_dst, but metadata_dst_free() wasn't
updated to check it before freeing the METADATA_IP_TUNNEL specific dst
cache entry.
This is not currently causing problems since it's far enough back in the
struct to be zeroed for the only other type currently in existance
(METADATA_HW_PORT_MUX), but nevertheless it's not correct.
Fixes: 3fcece12bc ("net: store port/representator id in metadata_dst")
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Sridhar Samudrala <sridhar.samudrala@intel.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-08-21
1) Support RX checksum with IPsec crypto offload for esp4/esp6.
From Ilan Tayari.
2) Fixup IPv6 checksums when doing IPsec crypto offload.
From Yossi Kuperman.
3) Auto load the xfrom offload modules if a user installs
a SA that requests IPsec offload. From Ilan Tayari.
4) Clear RX offload informations in xfrm_input to not
confuse the TX path with stale offload informations.
From Ilan Tayari.
5) Allow IPsec GSO for local sockets if the crypto operation
will be offloaded.
6) Support setting of an output mark to the xfrm_state.
This mark can be used to to do the tunnel route lookup.
From Lorenzo Colitti.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make code closer to current style. Mostly whitespace changes.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XPS queue attributes can be ro_after_init.
Also use __ATTR_RX macros to simplify initialization.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The show and store functions don't need/use the attribute.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The attributes of net devices are immutable.
Ideally, attribute groups would contain const attributes
but there are too many places that do modifications of list
during startup (in other code) to allow that.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net_class in sysfs is only modified on init.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are wrapper arount class_create_file which can take a
const attribute.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If kobject_init_and_add failed, then the failure path would
decrement the reference count of the queue kobject whose reference
count was already zero.
Fixes: 114cf58021 ("bql: Byte queue limits")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return error code need to be included in the tracepoint
xdp:xdp_redirect, else its not possible to distinguish successful or
failed XDP_REDIRECT transmits.
XDP have no queuing mechanism. Thus, it is fairly easily to overrun a
NIC transmit queue. The eBPF program invoking helpers (bpf_redirect
or bpf_redirect_map) to redirect a packet doesn't get any feedback
whether the packet was actually transmitted.
Info on failed transmits in the tracepoint xdp:xdp_redirect, is
interesting as this opens for providing a feedback-loop to the
receiving XDP program.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to commit e6afc8ace6 ("udp: remove
headers from UDP packets before queueing"), when udp packets are being
peeked the requested extra offset is always 0 as there is no need to skip
the udp header. However, when the offset is 0 and the next skb is
of length 0, it is only returned once. The behaviour can be seen with
the following python script:
from socket import *;
f=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
g=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
f.bind(('::', 0));
addr=('::1', f.getsockname()[1]);
g.sendto(b'', addr)
g.sendto(b'b', addr)
print(f.recvfrom(10, MSG_PEEK));
print(f.recvfrom(10, MSG_PEEK));
Where the expected output should be the empty string twice.
Instead, make sk_peek_offset return negative values, and pass those values
to __skb_try_recv_datagram/__skb_try_recv_from_queue. If the passed offset
to __skb_try_recv_from_queue is negative, the checked skb is never skipped.
__skb_try_recv_from_queue will then ensure the offset is reset back to 0
if a peek is requested without an offset, unless no packets are found.
Also simplify the if condition in __skb_try_recv_from_queue. If _off is
greater then 0, and off is greater then or equal to skb->len, then
(_off || skb->len) must always be true assuming skb->len >= 0 is always
true.
Also remove a redundant check around a call to sk_peek_offset in af_unix.c,
as it double checked if MSG_PEEK was set in the flags.
V2:
- Moved the negative fixup into __skb_try_recv_from_queue, and remove now
redundant checks
- Fix peeking in udp{,v6}_recvmsg to report the right value when the
offset is 0
V3:
- Marked new branch in __skb_try_recv_from_queue as unlikely.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given both program types are effecitvely doing the same in the
prologue, just reuse the one that we had for tc and only adapt
to the corresponding drop verdict value. That way, we don't need
to have the duplicate from 8a31db5615 ("bpf: add access to sock
fields and pkt data from sk_skb programs") to maintain.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are guaranteed to have a NULL ri->map in this branch since
we test for it earlier, so we don't need to reset it here.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main purpose of this tracepoint is to monitor bulk dequeue
in the network qdisc layer, as it cannot be deducted from the
existing qdisc stats.
The txq_state can be used for determining the reason for zero packet
dequeues, see enum netdev_queue_state_t.
Notice all packets doesn't necessary activate this tracepoint. As
qdiscs with flag TCQ_F_CAN_BYPASS, can directly invoke
sch_direct_xmit() when qdisc_qlen is zero.
Remember that perf record supports filters like:
perf record -e qdisc:qdisc_dequeue \
--filter 'ifindex == 4 && (packets > 1 || txq_state > 0)'
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently we added a new map type called dev map used to forward XDP
packets between ports (6093ec2dc3). This patches introduces a
similar notion for sockets.
A sockmap allows users to add participating sockets to a map. When
sockets are added to the map enough context is stored with the
map entry to use the entry with a new helper
bpf_sk_redirect_map(map, key, flags)
This helper (analogous to bpf_redirect_map in XDP) is given the map
and an entry in the map. When called from a sockmap program, discussed
below, the skb will be sent on the socket using skb_send_sock().
With the above we need a bpf program to call the helper from that will
then implement the send logic. The initial site implemented in this
series is the recv_sock hook. For this to work we implemented a map
attach command to add attributes to a map. In sockmap we add two
programs a parse program and a verdict program. The parse program
uses strparser to build messages and pass them to the verdict program.
The parse programs use the normal strparser semantics. The verdict
program is of type SK_SKB.
The verdict program returns a verdict SK_DROP, or SK_REDIRECT for
now. Additional actions may be added later. When SK_REDIRECT is
returned, expected when bpf program uses bpf_sk_redirect_map(), the
sockmap logic will consult per cpu variables set by the helper routine
and pull the sock entry out of the sock map. This pattern follows the
existing redirect logic in cls and xdp programs.
This gives the flow,
recv_sock -> str_parser (parse_prog) -> verdict_prog -> skb_send_sock
\
-> kfree_skb
As an example use case a message based load balancer may use specific
logic in the verdict program to select the sock to send on.
Sample programs are provided in future patches that hopefully illustrate
the user interfaces. Also selftests are in follow-on patches.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
