The pointer to the struct net_device in the private data is only
assigned but never used, so delete it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
arc_emac_priv, use stats from struct net_device.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both transmit and receive use the same infrastructure for calculating
the packet timestamp. Rather than duplicating the code, provide a
function to do this common work. Model this function in the Intel
e1000e version which avoids calling ns_to_ktime() within the spinlock;
the spinlock is critical for timecounter_cyc2time() but not
ns_to_ktime().
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless status check in the transmit reap path - we have
already checked that the BD_ENET_TX_READY bit is clear, and as the
hardware only ever clears this bit, there is no way this test can ever
be true.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we timeout on transmit, it would be useful to dump the transmit
ring, so we can see the ring state. This can be helpful to diagnose
the cause of transmit timeouts.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to merge two separate preprocessor conditionals together.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear any pending receive interrupt before we process a pending packet.
This helps to avoid any spurious interrupts being raised after we have
fully cleaned the receive ring, while still allowing an interrupt to be
raised if we receive another packet.
The position of this is critical: we must do this prior to reading the
next packet status to avoid potentially dropping an interrupt when a
packet is still pending.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of "better implementation of iMX6 ERR006358 quirk", we no longer have
a requirement for a delayed work. Moreover, the work is now only used
for timeout purposes, so the timeout flag is also pointless - we set it
each time we queue the work, and the work clears it.
Replace the fec_enet_delayed_work struct with a standard work_struct,
resulting in simplified timeout handling code.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a (delayed) workqueue for ERR006358 is not correct - a work queue
is a single-trigger device. Once the work queue has been scheduled, it
can't be re-scheduled until it has been run. This can cause problems -
with an appropriate packet timing, we can end up with packets queued,
but not sent by the hardware, resulting in the transmit timeout firing.
Re-implement this as per the workaround detailed in the ERR006358
documentation - if there are packets waiting to be sent when we service
the transmit ring, and we see that the transmitter is not running,
kick the transmitter to run the pending entries in the ring.
Testing here with a 10Mbit half duplex link sees the resulting iperf
TCP bandwidth increase from between 1 to 2Mbps to between 8 to 9Mbps.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many places call fec_restart() with the second parameter being some kind
of previously saved duplex value, but only two places call it with some
other setting. This is at odds with how the other link settings are
handled, and used to be racy before the rtnl locks were added to
fec_restart()'s various call paths.
Clean this up so all link capabilities are handled in the same way -
saved into the fec_enet_private structure, and then fec_restart() acts
on those settings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the link goes down, the adjust_link method will be called, but
there is no synchronisation to ensure that we won't be processing some
last remaining packets via the NAPI handlers while performing a reset of
the device.
Add the necessary synchronisation to ensure that packet processing
is complete before we stop and reset the FEC.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the features (receive checksumming) requires the hardware to be
reprogrammed, and also changes the checks in the receive packet
processing.
The current implementation has a race - fec_set_features() changes the
flags which alter the receive packet processing while the adapter is
active, and potentially receiving frames. Only after we've modified
the software flag do we shutdown and reconfigure the hardware.
This can lead to packets being received and marked with a valid checksum
(via CHECKSUM_UNNECESSARY) when the hardware checksum validation has not
yet been enabled.
We must quiesce the device, then change the software configuration for
this feature, and then resume the device if it was previously running.
The resulting code structure also allows us to add other configuration
features in this path without having to quiesce and resume the network
interface and device.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_set_features() calls fec_stop() to stop the transmit ring while the
transmit queue is still active. This can lead to the transmit ring
being restarted by an intervening packet queued for transmission, or
by the tx quirk timer expiring.
Fix this by disabling NAPI (which ensures that the NAPI handlers are
not running), and then take the transmit lock while we stop and
restart the adapter (which prevents new packets being queued).
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_suspend() calls fec_stop() to stop the transmit ring while the
transmit packet processing is still active. This can lead to the
transmit queue being restarted by an intervening packet queued for
transmission, or by the tx quirk timer expiring.
Fix this by disabling NAPI first, which will ensure that the NAPI
handlers are not running. Then, take the transmit lock before
detaching the netif device. This ensures that there are no races
with the transmit path - and also ensures that the watchdog won't
fire.
We can then safely stop the ethernet device itself, knowing that the
rest of the driver is safely shut down.
On resume, we bring the device back up in reverse order - we restart
the device, reattach the device (under the tx lock), and then enable
the NAPI handlers.
We also need to adjust the close function to cope with this new
sequence, so that it's possible to cleanly close down the driver
after the hardware fails to resume (eg, due to the regulator_enable()
or pinctrl calls in the resume path returning an error.)
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the second stage to "move calls to quiesce/resume packet
processing out of fec_restart()", where we remove calls which are not
appropriate to the call site.
In the majority of cases, there is no need to detach and reattach the
interface as we are holding the queue xmit lock across the reset. The
exception to that is in fec_resume(), where we are already detached by
the suspend function. Here, we can remove the call to detach the
interface.
We also do not need to stop the transmit queue. Holding the xmit lock
is enough to ensure that the transmit packet processing is not running
while we perform our task. However, since fec_restart() always cleans
the rings, we call netif_wake_queue() (or netif_device_attach() in the
case of resume) just before dropping the xmit lock. This prevents the
watchdog firing.
Lastly, always call napi_enable() after the device has been reattached
in the resume path so that we know that the transmit packet processing
is already in an enabled state, so we don't call netif_wake_queue()
while detached.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the calls to quiesce and resume packet processing out of
fec_restart() to its call sites. This is the first step in a two stage
clean up of this code, where we just move the calls out of fec_restart()
without changing them. Not everywhere needs to issue these calls, and
not everywhere needs all of these calls to be issued.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling fec_restart() or fec_stop() while the device is down
or not present (iow suspended.)
Although the ndo_timeout method will only be called if the device is
present and running, we defer this to a work queue. The work queue
can run independently, and so needs to repeat these checks to ensure
that a restart doesn't occur after the device has been taken down or
detached for suspend. In this case, we call fec_restart() in the
resume path, so nothing is lost.
For fec_set_features, we add a call to fec_restart() in fec_enet_open()
to ensure that the hardware is appropriate programmed when the interface
is opened. fec_set_features() call should not occur while we're
suspended, so we don't have to worry about that case.
The adjust_link needs similar treatment - this also is called from a
work queue, which may be run independently after we have taken the
device down and detached it. In this case, we just mark the link
down and take no further action. We will reset things appropriately
once the device is up and running again, at which point we will receive
another adjust_link callback.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the FEC is suspended, the device is detached. Upon resume failure,
the device is left in detached mode, possibly with some of the required
clocks not running. We don't want to be poking the device in that state
because as it may cause bus errors.
If the device is marked detached, avoid calling fec_stop().
This depends upon: "net:fec: improve safety of suspend/resume paths"
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should hold the rtnl lock while suspending, resuming or processing
the transmit timeout to ensure that nothing will interfere while we
bring up, take down or restart the hardware. The transmit timeout
could run if we're preempted during suspend.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a local copy of dev_addr in mlx4_en_set_mac() to prevent dev_addr
from being modified during error flow or when dev_addr is modified in
another context (which is another problem that is being discussed over
the mailing list [1]).
Also fixing bad naming of priv->prev_mac into priv->current_mac.
[1] - http://patchwork.ozlabs.org/patch/351489/
Reviewed-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LLC/SNAP 8 bytes should not be added as part of header calculation.
If used, payload will be decreased accordingly. For MTU of 1500
we'll set 1522 instead of 1523.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Liran Liss <liranl@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Promiscous mode is only for MACs.
Should not disable/enable VLAN filter when entering/leaving promisuous mode.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify port number to avoid crashes if port number is outside the range.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loopback can't work when port is down.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 40GE we can't use the default bw units for set ratelimit (100 Mbps)
since the max is 255*100 Mbps = 25 Gbps (not suited for 40GE), thus we need 1 Gbps units.
But for 10GE 1 Gbps units might be too bruit so we use the following solution.
For user set ratelimit <= 25 Gbps:
use 100 Mbps units * user_ratelimit (* 10).
For user set ratelimit > 25 Gbps:
use 1 Gbps units * user_ratelimit.
For user set unlimited ratelimit (0 Gbps):
use 1 Gbps units * MAX_RATELIMIT_DEFAULT (57)
Note: any value > 58 will damage the FW ratelimit computation, so we allow
a max and any higher value will be pulled down to 57.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes compiler warnings:
drivers/net/ethernet/amd/declance.c: In function 'lance_init_ring':
drivers/net/ethernet/amd/declance.c:478: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:487: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:503: warning: cast from pointer to integer of different size
drivers/net/ethernet/amd/declance.c:520: warning: cast from pointer to integer of different size
in 64-bit compilation. Where the value printed is an offset (whose range
will always fit) the cast uses a 32-bit type, otherwise, where it is a
host memory address, the pointer is output directly with %p. Also the
remaining `0x' prefix is dropped for consistency across these messages.
Tested with both 32-bit and 64-bit compilation, as well as at the run time
(with the debug messages affected enabled).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default cache operations for ARM64 were changed during 3.15.
To use coherent operations a "dma-coherent" device tree property
is required. If that property is not present in the device tree
node then the non-coherent operations are assigned for the device.
Add support to the amd-xgbe driver to assign the AXI DMA cache settings
based on whether the "dma-coherent" property is present in the device
node. If present, use settings that work with the caches. If not
present, use settings that do not look at the caches.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides some general performance enhancements for the
driver:
- Modify the default coalescing settings (reduce usec, increase frames)
- Change the AXI burst length to 256 bytes (default was 16 bytes which
was smaller than a cache line)
- Change the AXI cache settings to write-back/write-allocate which
allocate cache entries for received packets during the DMA since the
packet will be processed soon afterwards
- Combine ioread/iowrite when disabling both the Tx and Rx interrupts
- Change to processing the Tx/Rx channels in pairs
- Only recycle the Rx descriptors when a threshold of dirty descriptors
is reached
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the napi context is added using netif_napi_add each time
the ndo_open operation is called. However, there is not a
corresponding netif_napi_del call during the ndo_stop operation. If
the device ndo_open operation was called more than once an infinite
loop occurs during module unload. Add a call to netif_napi_del during
the ndo_stop operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the MTL interrupts the interrupt status
register is written to instead of the interrupt enable register.
Since no MTL interrupts are being enabled and the default state
is for MTL interrupts to be disabled this did not cause a problem,
but needs to be fixed to target the correct register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial change from sscanf to kstrtouint broke backward
compatbility by using a base of "0" in the kstrtouint call.
This allowed for entering decimal, hexadecimal or octal as
input where previously the sscanf always interpreted the input
as hexadecimal. Additionally, -EIO was returned on error prior
to this change and now it is whatever the error value that is
returned by kstrtouint.
Change the base value of the kstrtouint from 0 to 16 and return
-EIO on error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic_set_coalesce() has two problems.
* It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values.
* In case of MSIX, enic_set_coalesce return error after applying requested
coalescing setting partially. We should either apply all the setting requeste
and return success or apply non and return error.
* This patch also simplifies the algo.
This was introduced by
'7c2ce6e60f703 enic: Add support for adaptive interrupt coalescing'
These changes were suggested by Ben Hutchings here
http://www.spinics.net/lists/netdev/msg283972.html
Also change enic driver version.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-07-02
This series contains updates to i40e and i40evf.
Anjali fixes a possible race where we were trying to free the dummy packet
buffer in the function that created it, so cleanup the dummy packet buffer
in i40e_clean_tx_ring() instead. Also fixes an issue where the filter
program routine was not checking if there were descriptors available for
programming a filter.
Mitch fixes unnecessary delays when sending the admin queue commands by
moving a declaration up one level so we do not dereference it out of scope.
Fixes an issue with the VF where if the admin queue interrupts get lost for
some reason, the VF communication will stall as the VFs have no way of
reaching the PF. To alleviate this condition, go ahead and check the ARQ
every time we run the service task. Updates i40evf to allow the watchdog
to fire vector 0 via software, which makes the driver tolerant of dropped
interrupts on that vector.
Paul fixes a shifted '1' to be unsigned to avoid shifting a signed integer.
Jesse disables TPH by default since it is currently not enabled in the
current hardware. Also finishes the i40e implementation of get_settings
for ethtool.
Catherine adds a new variable (hw.phy.link_info.an_enabled) to track whether
auto-negotiation is enabled, along with the functionality to update the
variable. Adds the functionality to set the requested flow control mode.
Adds i40e implementation of setpauseparam and set_settings to ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_alloc_buffers() assumes that kmalloc() will never fail, which
is an invalid assumption. Fix this by implementing a common error
cleanup path, and use it to also clean up after failed bounce buffer
allocation.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we do not double-free any allocations, and that any transmit
skbuffs are properly freed when we clean up the rings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid writing any state until we're certain we can proceed with the
transmission: this avoids writing mapping error address values to the
descriptors, or setting the skbuff pointer until we have successfully
mapped the skb.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate, and then map the receive skb before writing any data to the
ring descriptor or storing the skb. When freeing the receive ring
entries, unmap and free the skb, and then clear the stored skb pointer.
This means we have ring data and skb pointer in one of two states:
either both fully setup, or nothing setup.
This simplifies the cleanup, as we can use just the skb pointer to
indicate whether the descriptor is setup, and thus avoids potentially
calling dma_unmap_single() on a DMA error value.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls. At this point, the driver then clears
fep->opened. The NAPI poll function uses this to stop processing in
the receive path. Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.
Therefore, this variable serves no purpose, so let's remove it.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the network interface goes down, stop the phy to prevent further
link up status changes before taking the MAC or netif sections down.
This prevents further reception of link up events which could
potentially call fec_restart().
Since phy_stop() takes the mutex which adjust_link() runs under, we
also ensure that adjust_link() will not already be processing a link
up event.
We also need to do this when suspending as well - we don't want a
mis-timed phy state change to restart the MAC after we have stopped
it for suspend, and thus need to restart the phy when resuming.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disconnect from a phy, we should forget our pointer to it so we
don't accidentally try to configure it. We handle a NULL phy pointer
correctly in most places, except fec_enet_set_pauseparam(). Fix this
too.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fep->phy_dev can not be NULL here for two reasons:
- fec_enet_open() will have successfully connected the phy, or will have
failed.
- fec_enet_open() will have called phy_start(fep->phy_dev), which
unconditionally dereferences this pointer.
If it were to be NULL here, then fec_enet_open() will have already
oopsed.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use netif_stop_queue() in several places where we want to ensure that
the start_xmit function is not running. netif_stop_queue() is not
sufficient to achieve that - it merely sets a flag to indicate that the
transmit queue(s) should not be run.
netif_tx_disable() gives this guarantee, since it takes the transmit
queue lock while marking the queue stopped. This will wait for the
transmit function to complete before returning.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running: while :; do iperf -c <HOST> -P 4; done, transmit timeouts
are regularly reported. With the tx ring dumping in place, we can see
that all entries are in use, and the hardware has finished transmitting
these packets. However, the driver has not reclaimed these ring
entries.
This can occur if the interrupt handler is invoked at the wrong moment -
eg:
CPU0 CPU1
fec_enet_tx()
interrupt, IEVENT = FEC_ENET_TXF
FEC_ENET_TXF cleared
napi_schedule_prep()
napi_complete()
The result is that we clear the transmit interrupt, but we don't trigger
any cleaning of the transmit ring. Instead, use a different strategy:
- When receiving a transmit or receive interrupt, disable both tx and rx
interrupts, but do not acknowledge them. Schedule a napi poll. Don't
loop.
- When we are polled, read IEVENT, acknowledging the pending transmit
and receive interrupts, before then going on to process the
appropriate rings.
This allows us to avoid the race, and has a number of other advantages:
- we cut down on the number of transmit interrupts we have to process.
- we only look at the rings which have pending events.
- we gain additional throughput: the iperf total bandwidth increases
from about 180Mbps to 240Mbps:
[ 3] 0.0-10.0 sec 68.1 MBytes 57.0 Mbits/sec
[ 5] 0.0-10.0 sec 72.4 MBytes 60.5 Mbits/sec
[ 4] 0.0-10.1 sec 76.1 MBytes 63.5 Mbits/sec
[ 6] 0.0-10.1 sec 71.9 MBytes 59.9 Mbits/sec
[SUM] 0.0-10.1 sec 288 MBytes 241 Mbits/sec
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the pause parameters causes a running network interface to be
restarted. However, the restart forces the FEC into half-duplex mode,
whether or not the remote end is in half-duplex mode. Misconfigured
duplex mode is a known source of problems on a link.
Fix this by always preserving the duplex mode on configuration changes.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The iMX6 gigabit FEC does not support half-duplex gigabit operation.
Phys attacked to the FEC may support this, and we currently do nothing
to disable this feature. This may result in an invalid configuration.
Mask out phy support for gigabit half-duplex operation.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Wake-on-LAN using Magic Packet with or without SecureOn
password is implemented doing the following:
- setting the password to the relevant UniMAC registers
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- enabling the MPD interrupt to wake us
The Device Tree binding documentation is also reflected to specify the
third optional Wake-on-LAN interrupt line.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This boolean tells us whether we are using the RXCHK hardware block,
so use a variable name that reflects that. RXCHK might be used in the
future to implement Wake-on-LAN using ARP or unicast packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the hardware recommended suspend/resume procedure for
SYSTEMPORT. We leverage the previous factoring work such that we can
logically break all suspend/resume operations into disctint RX and TX
code paths.
When the system enters S3, we will loose all register contents, so
make sure that we correctly re-program all the hardware and software
views of the RX & TX rings as well.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor common code that either enables or disables the network
interface with the networking stack. We are going to reuse these
functions for suspend/resume callbacks.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite often we need to enable either the transmitter or the receiver
bits in UMAC_CMD, use umac_enable_set() to do that for us.
This is a preliminary change to introduce suspend/resume support in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
