memcpy() call with "idata == NULL && ilen == 0" results in undefined
behavior in ar5523_cmd(). For example, NULL is passed in callchain
"ar5523_stat_work() -> ar5523_cmd_write() -> ar5523_cmd()". This patch
adds ilen check before memcpy() call in ar5523_cmd() to prevent an
undefined behavior.
Cc: Pontus Fuchs <pontus.fuchs@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_TLV_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath10k will check the capability, and if it is enabled then
ath10k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath10k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware to enable/disable the radio
and also notifies cfg80211.
We can't power off the device when rfkill is enabled, as otherwise the
firmware would not be able to detect GPIO changes and report them to the
host. So when rfkill is enabled, we need to keep the firmware running.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch restores the old behavior that read
the chip_id on the QCA988x before resetting the
chip. This needs to be done in this order since
the unsupported QCA988x AR1A chips fall off the
bus when resetted. Otherwise the next MMIO Op
after the reset causes a BUS ERROR and panic.
Cc: stable@vger.kernel.org
Fixes: 1a7fecb766 ("ath10k: reset chip before reading chip_id in probe")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Offchannel management frames were failing:
[18099.253732] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18102.293686] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18105.333653] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18108.373712] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18111.413687] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18114.453726] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
[18117.493773] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18120.533631] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
This bug appears to have been added between 4.0 (which works for us),
and 4.4, which does not work.
I think this is because the tx-offchannel logic gets in a loop when
ath10k_mac_tx_frm_has_freq(ar) is false, so pkt is never actually
sent to the firmware for transmit.
This patch fixes the problem on 4.9 for me, and now HS20 clients
can work again with my firmware.
Antonio: tested with 10.4-3.5.3-00057 on QCA4019 and QCA9888
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Antonio Quartulli <antonio.quartulli@kaiwoo.ai>
[kvalo@codeaurora.org: improve commit log, remove unneeded parenthesis]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rs_datalen is be16 so we need to convert it before printing.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, data variable in ar9003_hw_thermo_cal_apply() could be
uninitialized if ar9300_otp_read_word() will fail to read the value.
Initialize data variable with 0 to prevent an undefined behavior. This
will be enough to handle error case when ar9300_otp_read_word() fails.
Fixes: 80fe43f2bb ("ath9k_hw: Read and configure thermocal for AR9462")
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stable@vger.kernel.org
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In a multiradio board with one QCA9984 and one AR9987
after enabling the crashdump with module parameter
coredump_mask=7, below backtrace is seen.
vmalloc: allocation failure: 0 bytes
kworker/u4:0: page allocation failure: order:0, mode:0x80d2
CPU: 0 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.77 #130
Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
(unwind_backtrace) from [<c021abf8>] (show_stack+0x10/0x14)
(dump_stack+0x80/0xa0)
(warn_alloc_failed+0xd0/0xfc)
(__vmalloc_node_range+0x1b4/0x1d8)
(__vmalloc_node+0x34/0x40)
(vzalloc+0x24/0x30)
(ath10k_coredump_register+0x6c/0x88 [ath10k_core])
(ath10k_core_register_work+0x350/0xb34 [ath10k_core])
(process_one_work+0x20c/0x32c)
(worker_thread+0x228/0x360)
This is due to ath10k_hw_mem_layout is not defined for AR9987.
For coredump undefined hw ramdump_size is 0.
Check for the ramdump_size before allocation memory.
Tested on: AR9987, QCA9984
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IRAM start address in coredump was wrong for QCA9984, QCA4019, QCA9888 and
QCA99x0.
Tested on: QCA9984, QCA4019
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since ath10k_mac_tx_push_txq() can be called from process context, we
must explicitly disable softirqs before the call into mac80211.
By calling ieee80211_tx_dequeue_ni() instead of ieee80211_tx_dequeue()
we make sure softirqs are always disabled even in the case when
ath10k_mac_tx_push_txq() is called from process context.
Calling ieee80211_tx_dequeue_ni() with softirq's already disabled
(e.g., from softirq context) should be safe as the local_bh_disable()
and local_bh_enable() functions (called from ieee80211_tx_dequeue_ni)
are fully reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Software version within WMI event ready message was displayed
in a not very useful decimal format. Change this info to be shown
in a hexadecimal format instead.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add vht_supp_mcs argument to service ready structure and print
supported MCS rates in WMI service ready debug message.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Displays lowest/highest supported channels for both 2ghz and 5ghz
bands as they're fetched within WMI service ready event.
These are shown in a frequency format.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add lowest/highest 2ghz channel arguments for use within WMI service
ready structure.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath10k_usb_hif_tx_sg the allocated urb should be released if
usb_submit_urb fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently, it has the basic feature of sdio tested success, so remove
it.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are a bunch of spelling mistakes in two ath drivers, fix
these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_bmi_write32 and ath10k_bmi_read32 can fail. The fix
checks their statuses to avoid potential undefined behaviors.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the current implementation of wmi init command,
there is no provision for the host driver to provide mem
chunks addresses with more than 32-bit, to the firmware.
WCN3990 is a 35-bit target and can accept mem chunks addresses
which are above 32-bit.
If firmware supports address range more than 32 bit, it
advertises the support by setting the WMI_SERVICE_EXTEND_ADDRESS
service. Based on this service fill the upper bits of paddr while
providing the mem chunks in the wmi init command.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The peer param id for PEER_PARAM_USE_FIXED_PWR
is different for tlv and non-tlv firmware. This
causes incorrect peer param to be set by the driver
to the firmware(tlv/non-tlv).
Create seperate peer param map for tlv and non-tlv
firmware and attach the peer param id based on the
firmware type during the init.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MSA memory region caries the hw descriptors information.
Dump MSA region in core dump as this is very helpful in debugging
hw issues.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PMIC XO is the clock source for wifi rf clock in integrated wifi
chipset ex: WCN3990. Due to board layout errors XO frequency drifts
can cause wifi rf clock inaccuracy.
XO calibration test tree in Factory Test Mode is used to find the
best frequency offset(for example +/-2KHz )by programming XO trim
register. This ensure system clock stays within required 20 ppm
WLAN rf clock.
Retrieve the xo trim offset via system firmware (e.g., device tree),
especially in the case where the device doesn't have a useful EEPROM
on which to store the calibrated XO offset (e.g., for integrated Wifi).
Calibrated XO offset is sent to fw, which compensate the clock drift
by programing the XO trim register.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a spelling mistake in a ath10k_warn warning message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bad latency is found on QCA988x, the issue was introduced by
commit 4504f0e5b5 ("ath10k: sdio: workaround firmware UART
pin configuration bug"). If uart_pin_workaround is false, this
change will set uart pin even if uart_print is false.
Tested HW: QCA9880
Tested FW: 10.2.4-1.0-00037
Fixes: 4504f0e5b5 ("ath10k: sdio: workaround firmware UART pin configuration bug")
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If 'sta->tdls' is false, no cleanup is executed, leading to memory/resource
leaks, e.g., 'arsta->tx_stats'. To fix this issue, perform cleanup before
go to the 'exit' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
driver sends QMI_WLFW_MSA_INFO_REQ_V01 QMI request to firmware
and in response expects range of addresses and size to be mapped.
Add condition to check whether addresses in response falls
under valid range otherwise return failure.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use ath10k_pci_soc_read32 / ath10k_pci_soc_write32 functions for
the rest of warm_reset functions. Until now these have been used
only for ath10k_pci_warm_reset_si0, but since they already exist
it makes sense to simplify code a bit.
Runtime tested with QCA9862.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_bss_info_changed() handles various events from the upper layers. It
parses the changed bitfield and then configures the driver/firmware
accordingly. Each detected event is handled in a separate scope which is
independent of each other - but in the same function.
The commit f279294e9e ("ath10k: add support for configuring management
packet rate") changed this behavior by returning from this function
prematurely when some precondition was not fulfilled. All new event
handlers added after the BSS_CHANGED_BASIC_RATES event handler would then
also be skipped.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No frequency is currently specified for the single clock defined in the
snoc driver, so the clock wrappers reimplements the standard bulk API
provided by the clock framework. Change to this.
The single clock defined is marked as optional so this version of the
get API is used, but might need to be reconsidered in the future.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regulator_get_optional() exists for cases where the driver needs do
behave differently depending on some regulator supply being present or
not, as we don't use this we can use the standard regulator_get() and
rely on its handling of unspecified regulators.
While the driver currently doesn't specify any loads the regulator
framework was updated last year to only account for load of enabled
regulators, so should the need appear it's better to apply load numbers
during initialization that dynamically.
With this the regulator wrappers have been reduced the become identical
to the standard bulk API provided by the regulator framework, so use
these instead of rolling our own.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regulator operations is trying to set a voltage to a fixed value, by
giving some wiggle room. But some board designs specifies regulator
voltages outside this limited range. One such example is the Lenovo Yoga
C630, with vdd-3.3-ch0 in particular specified at 3.1V.
But consumers with fixed voltage requirements should just rely on the
board configuration to provide the power at the required level, so this
code should be removed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The introduction of 768ec4c012 ("ath10k: update HOST capability QMI
message") served the purpose of supporting the new and extended HOST
capability QMI message.
But while the new message adds a slew of optional members it changes the
data type of the "daemon_support" member, which means that older
versions of the firmware will fail to decode the incoming request
message.
There is no way to detect this breakage from Linux and there's no way to
recover from sending the wrong message (i.e. we can't just try one
format and then fallback to the other), so a quirk is introduced in
DeviceTree to indicate to the driver that the firmware requires the 8bit
version of this message.
Cc: stable@vger.kernel.org
Fixes: 768ec4c012 ("ath10k: update HOST capability qmi message")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are special kinds of FW such as WMI only which
are used for testing, diagnostics and other specific
scenario.
Such FW is loaded during driver probe and the driver
disallows enabling any network interface, to avoid
operational issues.
In many cases it is used to debug early versions
of FW with new features, which sometimes fail
on startup.
Currently when such FW fails to load (for example,
because of init failure), the driver probe would fail
and shutdown the device making it difficult to debug
the early failure.
To fix this, ignore load failures in WMI only FW and
allow driver probe to succeed, making it possible to
continue and debug the FW load failure.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The short frame check in wil_sring_reap_rx_edma uses
skb->len which store the maximum frame length. Fix
this to use dmalen which is the actual length of
the received frame.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
writel_relaxed can be used in wil_debugfs_iomem_x32_set
since there is a wmb call immediately after.
Signed-off-by: Lior David <liord@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Call cfg80211_inform_bss_frame_data to report cfg80211 on the
boottime_ns in order to prevent the scan results filtering due to
aging.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon driver rmmod, cancel_work_sync() can be invoked on
p2p.discovery_expired_work before this work struct was initialized.
This causes a WARN_ON with newer kernel version.
Add initialization of discovery_expired_work inside wil_vif_init().
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cid value is not being verified in wmi_evt_delba(),
verification is added.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Due to compiler optimization, it's possible that dr_bit (descriptor
ready) is read last from the status message.
Due to race condition between HW writing the status message and
driver reading it, other fields that were read earlier (before dr_bit)
could have invalid values.
Fix this by explicitly reading the dr_bit first and then using rmb
before reading the rest of the status message.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix a race between cfg80211 add_key call and transmitting of 4/4 EAP
packet. In case the transmit is delayed until after the add key takes
place, message 4/4 will be encrypted with the new key, and the
receiver side (AP) will drop it due to MIC error.
Wil6210 will monitor and look for the transmitted packet 4/4 eap key.
In case add_key takes place before the transmission completed, then
wil6210 will let the FW store the key and wil6210 will notify the FW
to use the PTK key only after 4/4 eap packet transmission was
completed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PMC is a hardware debug mechanism which allows capturing real time
debug data and stream it to host memory. The driver allocates memory
buffers and set them inside PMC ring of descriptors.
Add pmcring debugfs that application can use to read the binary
content of descriptors inside the PMC ring (cat pmcring).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move common part of wil_netif_rx_any into new helper function and add
support for non-gro receive using netif_rx_ni.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tlv targets such as WCN3990 send more data in the chan info event, which is
not sent by the non tlv targets. There is a minimum size check in the wmi event
for non-tlv targets and hence we cannot update the common channel info
structure as it was done in commit 13104929d2 ("ath10k: fill the channel
survey results for WCN3990 correctly"). This broke channel survey results on
10.x firmware versions.
If the common channel info structure is updated, the size check for chan info
event for non-tlv targets will fail and return -EPROTO and we see the below
error messages
ath10k_pci 0000:01:00.0: failed to parse chan info event: -71
Add tlv specific channel info structure and restore the original size of the
common channel info structure to mitigate this issue.
Tested HW: WCN3990
QCA9887
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
10.2.4-1.0-00037
Fixes: 13104929d2 ("ath10k: fill the channel survey results for WCN3990 correctly")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the FW bundles multiple packets, pkt->act_len may be incorrect
as it refers to the first packet only (however, the FW will only
bundle packets that fit into the same pkt->alloc_len).
Before this patch, the skb length would be set (incorrectly) to
pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually
adjusted in ath10k_sdio_mbox_rx_process_packet.
The first problem is that ath10k_sdio_mbox_rx_process_packet does not
use proper skb_put commands to adjust the length (it directly changes
skb->len), so we end up with a mismatch between skb->head + skb->tail
and skb->data + skb->len. This is quite serious, and causes corruptions
in the TCP stack, as the stack tries to coalesce packets, and relies
on skb->tail being correct (that is, skb_tail_pointer must point to
the first byte_after_ the data).
Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet,
this moves the code to ath10k_sdio_mbox_rx_packet, and also add a
bounds check, as skb_put would crash the kernel if not enough space is
available.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Fixes: 8530b4e7b2 ("ath10k: sdio: set skb len for all rx packets")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My wave-1 firmware often crashes when I am bringing down
AP vdevs, and sometimes at least some machines lockup hard
after spewing IOMMU errors.
I don't see the same issue in STA mode, so I suspect beacons
are the issue.
Moving the beacon buf deletion to later in the vdev teardown
logic appears to help this problem. Firmware still crashes
often, but several iterations did not show IOMMU errors and
machine didn't hang.
Tested hardware: QCA9880
Tested firmware: ath10k-ct from beginning of 2019, exact version unknown
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath9k_wmi_cmd, the allocated network buffer needs to be released
if timeout happens. Otherwise memory will be leaked.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
