Commit Graph

5 Commits

Author SHA1 Message Date
Ramneek Mehresh
621c4b999e powerpc/85xx: Add dr_mode property in USB nodes
Add usb2 controller node for P1020RDB, P2020RDB, P2020DS, P1021MDS

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-18 08:05:42 -06:00
Andy Fleming
220669495b powerpc: Add TBI PHY node to first MDIO bus
Systems which use the fsl_pq_mdio driver need to specify an
address for TBI PHY transactions such that the address does
not conflict with any PHYs on the bus (all transactions to
that address are directed to the onboard TBI PHY). The driver
used to scan for a free address if no address was specified,
however this ran into issues when the PHY Lib was fixed so
that all MDIO transactions were protected by a mutex. As it
is, the code was meant to serve as a transitional tool until
the device trees were all updated to specify the TBI address.

The best fix for the mutex issue was to remove the scanning code,
but it turns out some of the newer SoCs have started to omit
the tbi-phy node when SGMII is not being used. As such, these
devices will now fail unless we add a tbi-phy node to the first
mdio controller.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2012-01-04 15:33:51 -06:00
Kumar Gala
ffeb33d20c powerpc/85xx: Rework P1021MDS device tree
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.

Other changes include:

* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
  moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1021-IP..." from compatibles for standard blocks

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-24 02:01:38 -06:00
Anton Vorontsov
dee9ad718b powerpc/85xx: Fix booting for P1021MDS boards
P1021 processors have no dedicated ROM to store the QE microcode,
so the fimrware is stored externally, and it is U-Boot responsibility
to load it. It might be that the board is booting without QE, e.g.
currently U-Boot doesn't support QE for P1021MDS boards, which means
that QE isn't initialized, and so the board hangs early at boot.

This patch fixes the issue by marking QE as disabled and checking the
state in the probing code. U-Boot should fixup the state if it
initialized the QE.

Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-04 14:16:01 -05:00
Haiying Wang
48936a08b8 powerpc/85xx: Add P1021MDS board support
P1021 is a dual e500v2 core based SOC with:
* 3 eTSECs (eTSEC1/3 RGMII, eTSEC2 SGMII on this board)
* 2 PCIe Controller
* 1 USB2.0 controller
* eSDHC, eSPI, I2C, DUART
* eLBC (NAND, BCSR, PMC0/1)
* Security Engine (SEC 3.3.2)
* Quicc Engine (QE)

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Yu Liu <Yu.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-24 21:29:25 -05:00